Search Results

Search found 2022 results on 81 pages for 'subnet mask'.

Page 66/81 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• Add IPv6 support to DirectAdmin server

  - by George Boot

  I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

  Read the article

• windows clients cannot get dns resolution until you open and close ipv4 properties page

  - by GC78

  This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

  Read the article

• There's no sound on Ubuntu with an Intel HDA onboard chip and Realtek ALC1200 codec.

  - by Hanno Fietz

  For a while now, my sound has not been working in Ubuntu. It used to play OK, but after some upgrade (might have been distro upgrade to 9.10), it stopped working. I'm currently running 10.04 on an amd64 architecture. I'm using the builtin audio on a Foxconn motherboard, it's an ATI / Intel HDA chip with an Azalia controller, apparently it's using the Realtek ALC1200 codec. All the gory details here. I found a nice sound troubleshooting tutorial here, which is well-written and pretty extensive, however, I fail to look up the supported "models" for my soundcard. The troubleshooting page says to look for a section giving the codec used by your soundcard, which looks like this for me: !!HDA-Intel Codec information !!--------------------------- --startcollapse-- Codec: Realtek ALC1200 Then, I'm supposed to lookup the models for that codec in the file Documentation/ALSA-Configuration.txt in the appropriate directory of ALSA's git repository. Mine actually pointed me to a separate file, Documentation/HD-Audio-Models.txt, which, for my driver version is located here and contains no section related to ALC1200 codecs. I tried putting the driver options probe-mask=1 and model=auto in a config file for modprobe, as suggested elsewhere, but this just lead to snd-hda-intel not able to load at all anymore. I also tried installing the linux-backports-modules-alsa package for my kernel, because the description sounded promising, but that didn't change anything, either.

  Read the article

• Windows server 2008R2 routing with single NIC

  - by Fabian

  I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

  Read the article

• Apache and linux file permissions

  - by morpheous

  I recently moved a Symfony 1.3.2 website (a PHP web framework), from a windows machine to Linux (Ubuntu 9.10). Ever since then, I have had all kinds of problems involving file permission (even though the app run without any of these problems on windows). I run symfony fix-perms which applied a 777 mask to the web directory (presumably, including its sub folders) - (as an aside) I think that is a potential security hole ... I have been meaning to come in here to ask how to correctly set permissions. Currently, when attempting to save a file from my website, I am getting the following error: PHP Warning: imagejpeg() [0function.imagejpeg0]: Unable to open '/home/morpheous/work/webdev/frameworks/symfony/sites/project1/web/uploads/../images/thumbnail/959cd604cf6115014a3703bef5a50486a5520642.jpg' for writing: Permission denied in /home/morpheous/work/webdev/frameworks/symfony/sites/project1/apps/frontend/lib Here are the permissions on the folders: web drwxr-xr-x 16 morpheous morpheous 4096 2010-02-24 21:01 web web/uploads/../images drwxr-xr-x 13 morpheous morpheous 12288 2010-04-09 15:25 images web/uploads/../images/thumbnail drwxr-xr-x 3 morpheous morpheous 4096 2010-02-24 20:44 thumbnail Can someone kindly tell me how to set the permissions so that my website (presumably running as the Apache daemon) can write the files to the directory required above?

  Read the article

• Why do clients on Branch Sites insist on accessing SYSVOL on the HQ DC instead of the branches' RODC?

  - by pepoluan

  I'm still scratching my head over this situation... You see, we have 3 RW DCs in the HQ, and 1 RODC on every branch sites (50+ locations). During startup, a script will pull in some files from \\example.com\SYSVOL\example.com\Common\Data But we have been experiencing bandwidth overload. A traffic analysis indicated that lots of clients in the Branch Sites were trying to access the SYSVOL located in the RW DCs. E.g.: If the RW DCs are 10.1.0.15, 10.2.0.15, and 10.3.0.15, and site 'X' has a subnet of 10.27.0.0/16 (with its RODC at 10.27.0.15), clients at site 'X' seem to insist on accessing \\10.1.0.15\SYSVOL or \\10.2.0.15\SYSVOL or \\10.3.0.15\SYSVOL; they seem to be ignoring the RODC completely. What is going on here? Where should I start investigating what went wrong? BTW, I'm already using DFS-R, and replication have been going on successfully; I can put a small 'canary' file on one of the RW DCs, and within minutes all the RODCs will have successfully replicated the 'canary' file.

  Read the article

• How to stop my VPS from picking up ARP reqs it is not supposed to?

  - by Charles Stewart

  Machine: Xen-3.0 image running stable Debian Linux 2.6.18, pretty vanilla. My VPS provider asks me to deal with some trouble my image is causing, namely handling IP addresses it is not supposed to: The problem is that your server seems to be configured to use IPs that have not been appointed to you. Your server responds to ARP requests for the IPs 81.171.111.219 and 81.171.111.218. But you are not allowed to use those. Not explicitly, as far as I can tell! At least, nothing under /etc or /var/tmp mentions these IP addresses. But arp -v says something I can't make sense of: Address HWtype HWaddress Flags Mask Iface 81.171.111.1 ether 00:0C:DB:E3:80:00 C eth0 Entries: 1 Skipped: 0 Found: 1 What is it listening to? The possibilities seem to be: It's not my fault: my VPS providers have overlooked something. What might that be? 81.171.111.1 means I'm happy listening in on ARP requests that I shouldn't be: how do I change this? In any case, what does this mean? I'm looking in completely the wrong place for information on what my image is doing. Where should I be looking?

  Read the article

• Does Guest WiFi on an Access Point make any sense?

  - by uos??

  I have a Belkin WiFi Router which offers a feature of a secondary Guest Access WiFi network. Of course, the idea is that the Guest network doesn't have access to the computers/devices on the main network. I also have a Comcast-issues Cable Modem/Router device with mutliple wired ports, but no WiFi-capabilities. I prefer to only run one router/DHCP/NAT instead of both the Comcast Router and the Belkin Router, so I can disable the Routing functions of the Belkin and allow the Comcast Router to But if I disable the Routing functions of the Belkin device, the Guest WiFi network is still available. Is this configuration just as secure as when the Belkin acts as a Router? I guess the question comes down to this: Do Guest WiFi's provide security by 1) only allowing requests to IPs found in-front of the device, or do they work by 2) disallowing requests to IPs on the same subnet? 1) Would mean that Guest WiFi on an access point provides no benefit 2) Would mean that the Guest WiFi functionality can work even if the device is just an access point. Or maybe something else entirely?

  Read the article

• ntop to analyse bandwidth usage on multiple ASA 5505

  - by dunxd

  I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

  Read the article

• Search for partial IP address using Windows Search?

  - by Dr. Dre

  I have a folder, c:\projects\, added to Windows Index. I know the indexing is working because I search for stuff in this folder all the time and the results come up very fast, and I've never noticed any accuracy problem until now. (I have had to tweak Indexing options to expand which file types have their contents indexed rather than just the file name, etc, but after that Search has worked pretty well for me). I've encountered a problem while trying to search for references to a particular IP address subnet. I'm trying to find all references to IP's with the pattern "192.168.220.xxx" (AKA, the 192.168.220.0/24, AKA 192.168.220.0/255.255.255.0 IP/netmask). Within Windows Explorer: c:\projects**.* is indexed c:\projects\work\project1\network_list.txt contains several "192.168.220.xxx" IP's Indexing status says all items are indexed (193,000 items). When I try to search for partial IP match, there are no search results. Tried searching for: 192.168.220, 192.168, 192.168.220., 192.168.220., 192.168.220.?, 192.168.220.??, 192.168.220.???, 192.168., 192.168.. Also tried variants of all the above surrounded with double quotes. All the searches returned 0 results. Within MS Outlook 2007: My mailbox, and all my offline .pst's are indexed. I search in Outlook pretty frequently, so I'm pretty sure indexed searches work across inbox and all .pst's. Indexing status in Outlook says all items are indexed. I also have references to these IP's in email, and I'd like to find all of them. Basically same deal as above, can't search for "192.168.220.xxx" IP's. Any way to fix this?

  Read the article

• Setfacl configuration issue in Linux

  - by Balualways

  I am configuring a Linux Server with ACL[Access Control Lists]. It is not allowing me to perform setfacl operation on one of the directoriy /xfiles. I am able to perform the setfacl on other directories as /tmp /op/applocal/. I am getting the error as : root@asifdl01devv # setfacl -m user:eqtrd:rw-,user:feedmgr:r--,user::---,group::r--,mask:rw-,other:--- /xfiles/change1/testfile setfacl: /xfiles/change1/testfile: Operation not supported I have defined my /etc/fstab as /dev/ROOTVG/rootlv / ext3 defaults 1 1 /dev/ROOTVG/varlv /var ext3 defaults 1 2 /dev/ROOTVG/optlv /opt ext3 defaults 1 2 /dev/ROOTVG/crashlv /var/crash ext3 defaults 1 2 /dev/ROOTVG/tmplv /tmp ext3 defaults 1 2 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 /dev/ROOTVG/swaplv swap swap defaults 0 0 /dev/APPVG/home /home ext3 defaults 1 2 /dev/APPVG/archives /archives ext3 defaults 1 2 /dev/APPVG/test /test ext3 defaults 1 2 /dev/APPVG/oracle /opt/oracle ext3 defaults 1 2 /dev/APPVG/ifeeds /xfiles ext3 defaults 1 2 I have a solaris server where the vfstab is defined as cat vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - /dev/vx/dsk/bootdg/swapvol - - swap - no - swap - /tmp tmpfs - yes size=1024m /dev/vx/dsk/bootdg/rootvol /dev/vx/rdsk/bootdg/rootvol / ufs 1 no logging /dev/vx/dsk/bootdg/var /dev/vx/rdsk/bootdg/var /var ufs 1 no logging /dev/vx/dsk/bootdg/home /dev/vx/rdsk/bootdg/home /home ufs 2 yes logging /dev/vx/dsk/APP/test /dev/vx/rdsk/APP/test /test vxfs 3 yes - /dev/vx/dsk/APP/archives /dev/vx/rdsk/APP/archives /archives vxfs 3 yes - /dev/vx/dsk/APP/oracle /dev/vx/rdsk/APP/oracle /opt/oracle vxfs 3 yes - /dev/vx/dsk/APP/xfiles /dev/vx/rdsk/APP/xfiles /xfiles vxfs 3 yes - I am not able to find out the issue. Any help would be appreciated.

  Read the article

• weird routes automatically being added to windows routing table

  - by simon

  On our windows 2003 domain, with XP clients, we have started seeing routes appearing in the routing tables on both the servers and the clients. The route is a /32 for another computer on the domain. The route gets added when one windows computer connects to another computer and needs to authenticate. For example, if computer A with ip 10.0.1.5/24 browses the c: drive of computer B with ip 10.0.2.5/24, a static route will get added on computer B like so: dest netmask gateway interface 10.0.1.5 255.255.255.255 10.0.2.1 10.0.2.5 This also happens on windows authenticated SQL server connections. It does not happen when computers A and B are on the same subnet. None of the servers have RIP or any other routing protocols enabled, and there are no batch files etc setting routes automatically. There is another windows domain that we manage with a near identical configuration that is not exhibiting this behaviour. The only difference with this domain is that it is not up to date with its patches. Is this meant to be happening? Has anyone else seen this? Why is it needed when I have perfectly good default gateways set on all the computers on the domain?!

  Read the article

• How to crop Screen Recordings under Snow Leopard?

  - by willc2

  Quicktime Player for Snow Leopard now allows you record the screen. Awesome! Once you have a movie it will let you trim screen recordings for length. Is there a way to crop the movie's dimensions, either in QT or using some built-in or free software? Update: How to crop to an arbitrary size and aspect ratio? iMovie only seems to let you crop to the aspect ratio of the containing project. Result: Both good answers but since I have QuickTime Player 7 and Photoshop, that's the workflow I choose as the answer. NOTE: If you have Photoshop Extended, you can import a movie, use the crop tool, and Export the cropped movie. Not free or built-in, but convenient. To summarize the instructions from the video link ricbax posted: Open movie in QuickTime Player 7 Copy a frame and Paste it into a new document in Photoshop Draw a rectangular selection around the area to keep and fill with black Invert the selection and fill with white Save as .GIF, with 2 colors Back in QuickTime Player 7, open Movie Properties window Select the Video Track Select the Visual Settings Tab Drag and Drop the 2-color .GIF file onto the Mask drop area (or use choose file button) Export the (now cropped) movie DONE

  Read the article

• How to route to a secondary interface on the same physical ethernet?

  - by sjose3612611

  INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

  Read the article

• Multiple IP's using one NIC connectivity problem - Windows

  - by Vincent

  I have a frame relay network that is directly connected to a GPRS network. I also have a ADSL high speed network and recently I have been trying to achieve the following network configuration using windows 7 (Also tried XP) with no success to date. On one server I have two NIC's NIC1 I would like the following two static IP address's 10.0.1.110 and 10.0.1.200 the cisco router has a default gateway of 10.0.1.1 the ADSL is DHCP. NIC1 and the cisco router do not have access to the internet. NIC2 is setup for DHCP with a primary DNS and secondary DNS configured to enable internet connectivity. With NIC1 all incoming TCP connections are from IP address's starting with 10.192.x.x I cannot establish a TCP connection to both 10.0.1.110 and 10.0.1.200. Its either one or the other. I have a static route implemented in windows of: route -p 10.192.0.0 mask 255.255.0.0 10.0.1.1 metric 1 I have tried leaving out the gateway in the NIC1 and many other combinations with no success. Can anyone please help? What am I doing wrong?

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• Intel NIC X540-T1 non-functional in Ubuntu Server 12.04

  - by Jeff Carr

  I have installed three Intel X540-T1's in servers running Ubuntu Server 12.04, but all are non-functional, no link lights, no packets sent or received, and no connection on ip4 or ip6 whether set up as dhcp or static. Also, dmesg doesn't detect cable connection or disconnection. I updated the default ixgbe driver to Intel's latest version (3.11.33) with no change. The ethernet controller is being reported as X540-AT2 (which might be a problem that I can't figure out how to fix), but the subsystem is X540-T1 so I believe that might be intended. Does anyone have any experience with this that could assist? ifconfig eth2 eth2 Link encap:Ethernet HWaddr a0:36:9f:14:5f:ea inet addr:192.168.101.1 Bcast:192.168.101.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1<br> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ethtool -i eth2 driver: ixgbe version: 3.11.33 firmware-version: 0x8000037c bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes lspci -vvnns 08:00.0 08:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller 10 Gigabit X540-AT2 [8086:1528] (rev 01) Subsystem: Intel Corporation Ethernet Converged Network Adapter X540-T1 [8086:0002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (64-bit, prefetchable) [size=2M] Region 4: Memory at e8200000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at e8280000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: ixgbe Kernel modules: ixgbe

  Read the article

• Specify default group and permissions for new files in a certain directory

  - by mislav

  I have a certain directory in which there is a project shared by multiple users. These users use SSH to gain access to this directory and modify/create files. This project should only be writeable to a certain group of users: lets call it "mygroup". During an SSH session, all files/directories created by the current user should by default be owned by group "mygroup" and have group-writeable permissions. I can solve the permissions problem with umask: $ cd project $ umask 002 $ touch test.txt File "test.txt" is now group-writeable, but still belongs to my default group ("mislav", same as my username) and not to "mygroup". I can chgrp recursively to set the desired group, but I wanted to know is there a way to set some group implicitly like umask changes default permissions during a session. This specific directory is a shared git repo with a working copy and I want git checkout and git reset operations to set the correct mask and group for new files created in the working copy. The OS is Ubuntu Linux. Update: a colleague suggests I should look into getfacl/setfacl of POSIX ACL but the solution below combined with umask 002 in the current session is good enough for me and is much more simple.

  Read the article

• Fixed and dynamic IPs in ISC DHPD lead to double lease

  - by GorillaPatch

  I would like to have a small dynamic adress part and the most clients are assigned a fixed IP adress. My dhcpd.conf looks like this: use-host-decl-names on; authoritative; allow client-updates; ddns-updates on; # Einstellungen fuer DHCP leases default-lease-time 3600; max-lease-time 86400; lease-file-name "/var/lib/dhcpd/dhcpd.leases"; subnet 192.168.11.0 netmask 255.255.255.0 { ddns-updates on; pool { # IP range which will be assigned statically range 192.168.11.1 192.168.11.240; deny all clients; } pool { # small dynamic range range 192.168.11.241 192.168.11.254; # used for temporary devices } } group { host pc1 { hardware ethernet xx:xx:xx:xx:xx:xx; fixed-address 192.168.11.11; } } The motivation for the pool declaration with deny all hosts comes from the ISC DHCPD homepage http://www.isc.org/files/auth.html This will allow hosts to be first added to the network, where they will receive a temporary IP from the 241-254 adress range and then later write an explicit host declaration. Upon next connect it will receive the right configuration. The problem is that I am getting error messages that 192.168.11.13 has a dynamic and a static lease. I am a bit confused as I expected the pool declaration with deny all clients would not count as dynamic. Dynamic and static leases present for 192.168.11.13. Remove host declaration pc1 or remove 192.168.11.13 from the dynamic address pool for 192.168.11.0/24 Is there a way to have the DHCP server send an DHCPNA to clients if they have a host statement and retain this dynamic range?

  Read the article

• OpenVPN with MacOS X Client and same subnets in local and remote net.

  - by Daniel

  I have a homenetwork 192.168.1.0/24 with gteway 192.168.1.1 and a remote network with the same parameters. Now I want to create a OpenVPN tunnel between those networks. I have no problems with Windows, because Windows routes everything to 192.168.1.0/24 except 192.168.1.1 throught the tunnel. On MacOS X however I see the folling line in the Details window: 2010-05-10 09:13:01 WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] When I list the routes I get the following: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.1.1 UGSc 13 3 en1 127 localhost UCS 0 0 lo0 localhost localhost UH 12 3589 lo0 169.254 link#5 UCS 0 0 en1 192.168.1 link#5 UCS 1 0 en1 192.168.1.1 0:1e:e5:f4:ec:7f UHLW 13 17 en1 1103 192.168.1.101 localhost UHS 0 0 lo0 192.168.6 192.168.6.5 UGSc 0 0 tun0 192.168.6.5 192.168.6.6 UH 1 0 tun0 My Interfaces are en1 - My local Wifi network tun0 - The tunnel interface As can be seen from the routes above there is no entry for 192.168.1.0/24 that routes the traffic through the tunnel interface. When I manually route a single IP like 192.168.1.16 over the tunnel gateway 192.168.6.6, this works. Q: How do I set up my routes in MacOS X for the same behaviour as on windows, to route everything except 192.168.1.1 through the tunnel, but leave the default gateway to be my local 192.168.1.1 ?

  Read the article

• Windows server 2008R2 routing with single NIC

  - by Fabian

  I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

  Read the article

• how would it be possible to discover a cable modem's MAC remotely?

  - by amateurenthusiast

  i was reading the back archives of a canadian privacy law blog, and he linked to a judicial decision. apparently as part of an investigation in which were used yahoo chat and google's old 'hello' image trading program the officer was able to determine a suspect's modem's MAC address: In order to determine who STEPHTOSH was, the officer did a trace on a programme called WHO IS in an effort to learn from where STEPHTOSH was coming. WHO IS is a command program available to the public. The officer was able to ascertain that the person using the name STEPHTOSH was a Rogers Internet customer. The officer was able to obtain the Internet Protocol address, also known as the I.P. There is only one location for an I.P., which is unique to that subscriber. By use of the website known as DNS STUFF.com, one is able to find with which company this I.P. is registered. It was ascertained that the I.P. address used by STEPHTOSH was registered to Rogers Cable, from the Toronto area. The officer also learned the Cable Modem MAC address used by STEPHTOSH. This was all the information the officer was able to amass. now it was my understanding that the MAC address of any given device can only be accessed if you're only one 'hop' away on the Internet. the suspect in question was in Markham and the officer part of the Toronto Police, so it's conceivable that they both might have used Rogers internet. but would that still put them only one 'hop' away from each other? i thought the first hop after the modem was usually the ISP? and if he'd used a netBIOS query against this guy's machine it would return the ethernet card's MAC, not the modem's. so is this guy on the same rogers subnet as the suspect's cable modem, is that functionality part of google's Hello (i could only think that it would be possible if Hello operated as a virtual LAN or something), does the officer have remote access to the arp caches of the routers at Rogers or is he just full of crap and lying to make his case stronger?

  Read the article

• How to set up port forwarding on a dedicated server running CentOS 5.4 to use Ubuntu 9.0.4

  - by mairtinh

  The basic situation that I have is a dedicated server running CentOS 5.4 At the moment I have one VM running Ubuntu 9.0.4. Later on, I will want to add another VM running Windows Server 2003 but at the moment I am focusing on getting Ubuntu up and running. The Ubuntu installation is working fine but I'm seriously struggling to get port forwarding working so that I can access websites to be hosted on the Ubuntu VM. As a newbie to Linux, I am confused about the relationship between IPTables and VMWare's own port forwarding. Here's what I've tried so far. The IP of my server is xxx.xxx.xxx.xxx and the provider support have told me that the subnet mask is 255.255.255.0, the gateway address is xxx.xxx.xxx.1 and the network address is xxx.xxx.xxx.0. (Those latter two surprise me a bit, I expected private gateway/network address rather than public ones.) First of all I tried Bridged Networking but had no success at all in communicating with the machine other than through the VMware console. I tried pinging it from the host (using ssh into the host) but no joy; also no Inernet access from the VM. I changed the interfaces configuration from DHCP to Static, using a static address of 192.168.1.100 and setting the gateway to xxx.xxx.xxx.1 as advised by the provider. No real difference, still cannot ping the guest from the host or vice versa and no Internet access from the guest. Then I tried NAT. The host automatically set the IP address to 192.168.132.128 with a gateway of 192.168.132.2 Now the guest has Internet access out and when I do a VNC to the host and open Firefox with 192.168.132.128 I can see the hosted website okay but I still cannot get into it from outside. I mentioned that I'm a bit confused about IPtables and VMware port forwarding, what I meant is that I'm not sure whether IPtable forwarding should be set to the IP address of the guest interface (192.168.132.128 in this case) or the gateway address 192.168.132.2 . I have a feeling that I'm missing something very simple here, can anybody tell me what it is?

  Read the article

• Any non-custom way to manage iptables with fail2ban and libvirt+kvm?

  - by Peter Hansen

  I have an Ubuntu 9.04 server running libvirt/kvm and fail2ban (for SSH attacks). Both libvirt and fail2ban integrate with iptables in different ways. Libvirt uses (I think) some XML config and during startup (?) configures forwarding to the VM subnet. Fail2ban installs a custom chain (probably at init) and periodically modifies it to ban/unban probable attackers. I also need to install my own rules to forward various ports to servers running in VMs and on other machines, and set up rudimentary security (e.g. drop all INPUT traffic except the few ports I want open), and of course I'd like the ability to add/remove rules safely without restarting. It seems to me iptables is a powerful tool that's sorely lacking some sort of standardized way of juggling all this stuff. Every project, and every sysadmin, seems to do it differently! (And I think there's lots of "cargo cult" admin going on here, with people cloning crude approaches like "use iptables-save like so".) Short of figuring out the gory details of exactly how both of these (and potentially other) tools manipulate the netfilter tables, and developing my own scripts or just manually executing iptables commands, is there any way to safely work with iptables while not breaking the functionality of these other tools? Any nascent standards or projects defined to bring sanity to this area? Even a helpful web page I missed that might cover at least these two packages together?

  Read the article

• How to remove static IP from Mitel 5312 and enable DHCP

  - by jimbo

  I'm not sure this is the right forum for this question -- although I'm confident I'll be told if not! -- but I've read the fine manual (at least, such a manual as I have), I've googled and I cannot get any insight into where to even start solving this problem. I have a bunch of Mitel 5312 handsets, talking to a 3300 ICP controller. Some handsets are at a remote location, get an address from my DHCP server over there, and use the Mitel "Teleworker" extension to connect in over the Internet. The remaining handsets were set up with static IPs by a BT-supplied engineer, on the same subnet as the ICP itself. So far, so good. I have one remaining teleworker licence, and need to move a handset from the home location to the remote. I've managed to boot it and configure teleworker, but I cannot for the life of me see where I tell it to forget its static IP, and make a DHCP request. Any ideas? Should I be looking on the controller, or holding magic combinations of buttons on the handset itself? EDIT: Following some advice from Robert, below, I've broken out a spare device and reassigned the profile for this user's extension to the MAC of the new phone, and a new profile to the old MAC. Unfortunately this still doesn't get me anywhere -- the new handset now asks for the teleworker install password. I suspect I'm going to have to get a Mitel engineer involved here, since I've never been given that password... Unless anyone has any great ideas?

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >