Search Results

Search found 19625 results on 785 pages for 'local groups'.

Page 660/785 | < Previous Page | 656 657 658 659 660 661 662 663 664 665 666 667  | Next Page >

• Sync, share and backup policy using NAS

  - by Cue

  Trying to come up with a way to keep in sync while sharing and keeping a backup of my music/photos and movies. Currently I have an iMac in Greece and a MBP with me in the UK. As a result I've ended up with 2 iPhoto and iTunes libraries not to mention Documents scattered here and there, user settings etc. I also like to have a backup in case of a drive failure or the need to clean install. It seems that iPhoto and iTunes don't work really well with networked libraries. The way I think about it is to have a NAS where I keep my iTunes and iPhoto library but also rsync daily to my MBP to have a local copy. That way my files are shared across the network as well as act like a backup. In addition I get to have my files wherever I take my MBP but also have the ability to clean install. The tricky part comes from keeping in sync the iMac which is miles away. Again I'm considering a mirror setup (NAS, rsync to the iMac) as well as an rsync between the two NAS. It pretty much resembles the way Dropbox works, sans the requirement to go through their servers but I'm no "superuser" and don't really know if it is even feasible to have such a setup. Looks like there are so many things that can go wrong.

  Read the article

• Access to CD/DVD Drive is Denied through Windows 7 Explorer (Permission Problem)

  - by Synetech inc.

  A while ago I started having trouble with my optical drives. Both of them keep showing up in Explorer as CD/DVD drives on boot, but as soon as I put a disc in either one, it suddenly turns into a hard-drive—“local disk” is displayed in the Type column, though the File System column remains UDF/CDFS. (I though that maybe it was a permission issue on the registry key in HKLM\System\CurrentControlSet..., but I’m not so certain because of the next test.) When I try to open a disc (of any type), I get an access denied error message. If I open an elevated command-prompt, I am able to access the files. Also, if I kill Explorer and run it from an elevated command-prompt (thus giving Explorer elevated permissions), then I can access the files from Explorer. I’ve tried uninstalling and reinstalling the devices without success. The security dialog indicates that there are none set for the drives (no owner and no permissions). I tried setting the owner, but am only able to do so if there is a disc in it (it complains if it is empty), but the settings do not stick (if I immediately open the security dialog after setting it, it is empty again). I tried setting permissions, but that gives an error. I’ve included a screencap-flowchart of the security dialog of one of the drives below. (Yes, I made sure that there are no upper- or lower-filters, and yes, I ran sfc. I also made sure that in the policy editor, “devices: restrict CD-ROM...” is not set.) Does anyone know what the owner and permissions are supposed to be for optical drives and how to reset them?

  Read the article

• How to reduce celeryd memory consumption?

  - by Gringo Suave

  I'm using celery 2.5.1 with django on a micro ec2 instance with 613mb memory and as such have to keep memory consumption down. Currently I'm using it only for the scheduler "celery beat" as a web interface to cron, though I hope to use it for more in the future. I've noticed it is the biggest consumer of memory on my micro machine even though I have configured the number of workers to one. I don't have many other options set in settings.py: import djcelery djcelery.setup_loader() BROKER_BACKEND = 'djkombu.transport.DatabaseTransport' CELERYBEAT_SCHEDULER = 'djcelery.schedulers.DatabaseScheduler' CELERY_RESULT_BACKEND = 'database' BROKER_POOL_LIMIT = 2 CELERYD_CONCURRENCY = 1 CELERY_DISABLE_RATE_LIMITS = True CELERYD_MAX_TASKS_PER_CHILD = 20 CELERYD_SOFT_TASK_TIME_LIMIT = 5 * 60 CELERYD_TASK_TIME_LIMIT = 6 * 60 Here's the details via top: PID USER NI CPU% VIRT SHR RES MEM% Command 1065 wuser 10 0.0 283M 4548 85m 14.3 python manage_prod.py celeryd --beat 1025 wuser 10 1.0 577M 6368 67m 11.2 python manage_prod.py celeryd --beat 1071 wuser 10 0.0 578M 2384 62m 10.6 python manage_prod.py celeryd --beat That's about 214mb of memory (and not much shared) to run a cron job occasionally. Have I done anything wrong, or can this be reduced about ten-fold somehow? ;) Update: here's my upstart config: description "Celery Daemon" start on (net-device-up and local-filesystems) stop on runlevel [016] nice 10 respawn respawn limit 5 10 chdir /home/wuser/wuser/ env CELERYD_OPTS=--concurrency=1 exec sudo -u wuser -H /usr/bin/python manage_prod.py celeryd --beat --concurrency=1 --loglevel info --logfile /var/tmp/celeryd.log Update 2: I notice there is one root process, one user child process, and two grandchildren from that. So I think it isn't a matter of duplicate startup. root 34580 1556 sudo -u wuser -H /usr/bin/python manage_prod.py celeryd wuser 577M 67548 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 578M 63784 +- python manage_prod.py celeryd --beat --concurrency=1 wuser 271M 76260 +- python manage_prod.py celeryd --beat --concurrency=1

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Will a SQL Server client alias survive a sysprep?

  - by shufler

  I want to sysprep a Windows Server 2008 R2 SP1 machine that has SQL Server 2008 R2 SP1 installed (for reference, SQL Server 2008 R2 has a new sysprep feature that allows the instance to be sysprepped). On the server is a SQL Server client alias that points to the default SQL Server database engine instance. For reference, the alias is called Alias-SQLServer and has been configured in both 32-bit and 64-bit cliconfig versions (that is, both registry keys exist) The alias points to the local instance as the image will be used to create development VMs and the installation script for the application that is being developed will use the SQL Server client alias in order to generalize the installation scripts. I can't seem to find information about whether the sysprep tool will update the SQL Server client alias's registry keys with the server's new name once it's unsealed. My guess is that it is not; how is sysprep to know that the server name the alias points to will be different for each image? Right? Perhaps if the alias points to localhost instead of the server name this will work?

  Read the article

• Certificates in SQL Server 2008

  - by Brandi

  I need to implement SSL for transmissions between my application and Sql Server 2008. I am using Windows 7, Sql Server 2008, Sql Server Management Studio, and my application is written in c#. I was trying to follow the MSDN page on creating certificates and this under 'Encrpyt for a specific client', but I got hopelessly confused. I need some baby steps to get further down the road to implementing encryption successfully. First, I don't understand MMC. I see a lot of certificates in there... are these certificates that I should be using for my own encryption or are these being used for things that already exist? Another thing, I assume all these certificates are files are located on my local computer, so why is there a folder called 'Personal'? Second, to avoid the above issue, I did a little experiment with a self-signed assembly. As shown in the MSDN link above, I used SQL executed in SSMS to create a self-signed certificate. Then I used the following connection string to connect: Data Source=myServer;Initial Catalog=myDatabase;User ID=myUser;Password=myPassword;Encrypt=True;TrustServerCertificate=True It connected, worked. Then I deleted the certificate I'd just created and it still worked. Obviously it was never doing anything, but why not? How would I tell if it's actually "working"? I think I may be missing an intermediate step of (somehow?) getting the file off of SSMS and onto the client? I don't know what I'm doing in the least bit, so any help, advice, comments, references you can give me are much appreciated. Thank you in advance. :)

  Read the article

• RAID degraded on Ubuntu server

  - by reano

  We're having a very weird issue at work. Our Ubuntu server has 6 drives, set up with RAID1 as follows: /dev/md0, consisting of: /dev/sda1 /dev/sdb1 /dev/md1, consisting of: /dev/sda2 /dev/sdb2 /dev/md2, consisting of: /dev/sda3 /dev/sdb3 /dev/md3, consisting of: /dev/sdc1 /dev/sdd1 /dev/md4, consisting of: /dev/sde1 /dev/sdf1 As you can see, md0, md1 and md2 all use the same 2 drives (split into 3 partitions). I also have to note that this is done via ubuntu software raid, not hardware raid. Today, the /md0 RAID1 array shows as degraded - it is missing the /dev/sdb1 drive. But since /dev/sdb1 is only a partition (and /dev/sdb2 and /dev/sdb3 are working fine), it's obviously not the drive that's gone AWOL, it seems the partition itself is missing. How is that even possible? And what could we do to fix it? My output of cat /proc/mdstat: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid1 sda2[0] sdb2[1] 24006528 blocks super 1.2 [2/2] [UU] md2 : active raid1 sda3[0] sdb3[1] 1441268544 blocks super 1.2 [2/2] [UU] md0 : active raid1 sda1[0] 1464710976 blocks super 1.2 [2/1] [U_] md3 : active raid1 sdd1[1] sdc1[0] 2930133824 blocks super 1.2 [2/2] [UU] md4 : active raid1 sdf2[1] sde2[0] 2929939264 blocks super 1.2 [2/2] [UU] unused devices: <none> FYI: I tried the following: mdadm /dev/md0 --add /dev/sdb1 But got this error: mdadm: add new device failed for /dev/sdb1 as 2: Invalid argument Output of mdadm --detail /dev/md0 is: /dev/md0: Version : 1.2 Creation Time : Sat Dec 29 17:09:45 2012 Raid Level : raid1 Array Size : 1464710976 (1396.86 GiB 1499.86 GB) Used Dev Size : 1464710976 (1396.86 GiB 1499.86 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 15:55:07 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : lia:0 (local to host lia) UUID : eb302d19:ff70c7bf:401d63af:ed042d59 Events : 26216 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 0 0 1 removed

  Read the article

• TCP dies on a Linux laptop

  - by Roman Cheplyaka

  Once in several days I have the following problem. My laptop (Debian GNU/Linux testing) suddenly becomes unable to work with TCP connections to the internet. The following things continue to work fine: UDP (DNS), ICMP (ping) — I get instant response TCP connections to other machines in the local network (e.g. I can ssh to a neighbour laptop) everything is ok for other machines in my LAN But when I try TCP connections from my laptop, they time out (no response to SYN packets). Here's a typical curl output: % curl -v google.com * About to connect() to google.com port 80 (#0) * Trying 173.194.39.105... * Connection timed out * Trying 173.194.39.110... * Connection timed out * Trying 173.194.39.97... * Connection timed out * Trying 173.194.39.102... * Timeout * Trying 173.194.39.98... * Timeout * Trying 173.194.39.96... * Timeout * Trying 173.194.39.103... * Timeout * Trying 173.194.39.99... * Timeout * Trying 173.194.39.101... * Timeout * Trying 173.194.39.104... * Timeout * Trying 173.194.39.100... * Timeout * Trying 2a00:1450:400d:803::1009... * Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable * Success * couldn't connect to host * Closing connection #0 curl: (7) Failed to connect to 2a00:1450:400d:803::1009: Network is unreachable Restarting the connection and/or reloading the network card kernel module doesn't help. The only thing that helps is reboot. Clearly something is wrong with my system (everything else works fine), but I have no idea what exactly. I don't know how to reproduce this, but as I said, it happens every several days. My setup is a wireless router that is connected to the ISP via PPPoE. Any advice?

  Read the article

• Windows 7 Taskbar resets on every login

  - by Arne Mertz

  I like to reorder my Taskbar a bit, other than the Windows 7 default is. I use two "rows", the lower is for quicklaunch and other toolbars: This works perfectly, as long as I don't log off from the computer. Every time I log in, Windows 7 has messed up/reset the toolbar positions like this: So I have to drag them into position again and again, every morning. Fixing the taskbar positions won't help, I tried to google for the problem but it does not seem to be very common. Does anyone recognize that problem and has a solution? Update: This is not the AutoLogon bug. AutoLogon is off. We have installed Novell at our company, and it does not matter wether I log directly onto the Novell network or only to the computer first and to Novell later. Update2: I get the same issue when I logon without Novell, i.e. when I log on only to the computer. When I boot in safe mode, the taskbar looks essentially the same: Update3: KB979155 says it's "not applicable to my system". Creating a neew user is not an option since I don't have the admin privileges to do that - I have almost any other local admin privileges, though.

  Read the article

• Diagnosing Random Network Lag

  - by uesp

  I'm having trouble diagnosing some random lag on a 6 server LAMP cluster serving a MediaWiki site. While we're serving some 100 pages/sec the servers themselves are running fine with less than 0.5 load, no locked processes, no paging, no errors being logged, etc.... Lag is present on all servers and is random: one minute its fine the next it's there. DNS lookups on the servers are randomly slow. For example time nslookup google.com varies randomly from a few milliseconds to several seconds and sometimes times out entirely. While we use IP addresses internally on the cluster this may be a symptom of the root issue. We are not running our own DNS server. The Apache server-status pages randomly lag or time out. Benchmarking using ab between servers shows a few loads sometimes take 3000 ms (almost exactly). Benchmarking server-status on the local server itself usually shows no issue (it showed a lag only once among a few hundred tests). The servers are sitting behind a switch and a firewall which I don't have any access to so I don't know their setup or status. While we are under heavier than normal load a 2 Mbps incoming and 20 Mbps outgoing traffic shouldn't be stressing the switch or firewall should it? My feeling is that it is the switch/firewall or something above them in the ISP like their DNS but can't confirm it. I need some other tests or methods of diagnosing this lag to try and narrow down the ultimate cause.

  Read the article

• Trouble Letting Users Get to Certain Sites through Squid Proxy

  - by armani

  We have Squid running on a RHEL server. We want to block users from getting to Facebook, other than a couple specific sites, like our organization's page. Unfortunately, I can't get those specific pages unblocked without allowing ALL of Facebook through. [squid.conf] # Local users: acl local_c src 192.168.0.0/16 # HTTP & HTTPS: acl Safe_ports port 80 443 # File containing blocked sites, including Facebook: acl blocked dst_dom_regex "/etc/squid/blocked_content" # Whitelist: acl whitelist url_regex "/etc/squid/whitelist" # I do know that order matters: http_access allow local_c whitelist http_access allow local_c !blocked http_access deny all [blocked_content] .porn_site.com .porn_site_2.com [...] facebook.com [whitelist] facebook.com/pages/Our-Organization/2828242522 facebook.com/OurOrganization facebook.com/media/set/ facebook.com/photo.php www.facebook.com/OurOrganization My biggest weakness is regular expressions, so I'm not 100% sure about if this is all correct. If I remove the "!blocked" part of the http_access rule, all of Facebook works. If I remove "facebook.com" from the blocked_content file, all of Facebook works. Right now, visiting facebook.com/OurOrganization gives a "The website declined to show this webpage / HTTP 403" error in Internet Explorer, and "Error 111 (net::ERR_TUNNEL_CONNECTION_FAILED): Unknown error" in Chrome. WhereGoes.com tells me the URL redirects for that URL goes like this: facebook.com/OurOrganization -- [301 Redirect] -- http://www.facebook.com/OurOrganization -- [302 Redirect] -- https://www.facebook.com/OurOrganization I tried turning up the debug traffic out of squid using "debug_options ALL,6" but I can't narrow anything down in /var/log/access.log and /var/log/cache.log. I know to issue "squid -k reconfigure" whenever I make changes to any files.

  Read the article

• MySQL permissions error when showing databases

  - by Tony

  I was trying to install homebrew and very very stupidly did this: sudo chown -R $USER /usr/local The Homebrew instructions say to do this and I'm not much of a sysadmin so I took their word for it. Lesson learned (although I wouldn't really know how to test this...seems like an "undo" script would be super valuable here) Anyway, what is done is done, but now I get this error: $ mysql -u root -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 548 Server version: 5.1.33 Source distribution Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show databases; ERROR 1018 (HY000): Can't read dir of '.' (errno: 13) I tried chown-ing back to root with no avail. Does anyone know how I can fix this without reinstalling mysql? Optionally, if I have to reinstall mysql, how can I dump my databases without access to the command line so I don't lose all of my data. Thanks!

  Read the article

• Libvirt/KVM in NAT: can't access from host (and can't forward)

  - by SharkWipf

  I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

  Read the article

• Mapped network drive connection timeout

  - by Terix

  I have server "Alpha" and server "Beta". Server Beta has a shared folder, that is mapped on server Alpha as "X:" On server Alpha there is a .vbs script that runs and take some files on local drive and copy them on X: drive. My issue is if no user log on server Alpha for a long time, it seems like the tcp connection underneath the mapped drive has a timeout, and the vbs script fails on the copy of file. As soon I log with remote desktop on Alpha server, the .vbs is successfull on the copy of the files. I have made many tests, using file logs to check what was happening and I found no way to refresh the connection and let the .vbs be able to copy files unattended.. I have always to log with remote desktop on Alpha server to refresh the connection and let the .vbs copy the files without issues. What can I do to avoid to log every time? The .vbs script runs 3 times a day and is very annoying. I do not have control over server Beta so I cannot change anything there, and I am very limited on changes I can do on server Alpha ( I cannot change registry and that sort of things)

  Read the article

• What switch should we use for PCoIP?

  - by Jay R.

  We have a small lab space that seats 10 people and has 20 machines. Each machine is set to 1920x1200 resolution because the user apps are best used at that resolution. Currently the machines are all located close enough to montors that a DisplayPort cable will reach, but the pending lab remodel positions them around 80 feet or more away in racks. Our proposed solution is to use PCoIP. We purchased 10 PCoIP portals and 20 PCoIP host cards. We plan to set up a dedicated network to handle just the PCoIP traffic. After testing just one portal and one host card with a cheap 1G switch from a local office supply store, we were left with less than good impressions about the usefulness in our lab. The framerates were not spectacular and the mouse seemed jerky. Our concern is that we can't get away with the cheap 1G stuff from the store because adding more machines to the switch will just make the user experience worse. What switch would be recommended to best support our PCoIP situation? We will need to plug in at least 30 cables based on just those machines. Is there a particular feature to search for that makes a difference? Is there a switch that works best with PCoIP? Added Info: The reporting webapp for the host card shows maximum bandwidth usage to be 220000 kbps. The average appears to be around 180000 kbps. The reverse direction is much lower, like 15000 kbps.

  Read the article

• SSH from ubuntu server to Windows 2008 repeatedly asks for password

  - by jrizos

  I am trying to setup GIT using SSH mode. The central GIT repository is on a NAS device running Windows 2008 server and the user GIT repository is on ubuntu 12.04. When I try to SSH to the windows machine however I am not able to successfully get in. SSH keays are not setup but I think the problem is even before that since I cant get in just by providing the correct password. The output from the SSH command is below. Any help would be appreciated. dba@clpserv01:~$ ssh -v -l administrator clpnas OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to clpnas [***.***.***.***] port 22. debug1: Connection established. debug1: identity file /home/dba/.ssh/id_rsa type -1 debug1: identity file /home/dba/.ssh/id_rsa-cert type -1 debug1: identity file /home/dba/.ssh/id_dsa type -1 debug1: identity file /home/dba/.ssh/id_dsa-cert type -1 debug1: identity file /home/dba/.ssh/id_ecdsa type -1 debug1: identity file /home/dba/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5p1 Debian-6+squeeze2 debug1: match: OpenSSH_5.5p1 Debian-6+squeeze2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA bd:37:d1:98:51:2a:d6:b5:f5:c7:98:d8:74:2c:4e:cd debug1: Host 'clpnas' is known and matches the RSA host key. debug1: Found key in /home/dba/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /home/dba/.ssh/id_rsa debug1: Trying private key: /home/dba/.ssh/id_dsa debug1: Trying private key: /home/dba/.ssh/id_ecdsa debug1: Next authentication method: keyboard-interactive Password: debug1: Authentications that can continue: publickey,password,keyboard-interactive Password:

  Read the article

• Client cannot access my IIS7 web server

  - by Soccerwiz

  I have a Windows 2008 web server on running IIS 7 with about 25 websites. One of those sites is an SaaS application that is accessed constantly throughout the day. However, one particular client keeps getting blocked from my server. They will be using the service, and then all of a sudden they cannot access the program, or any other site on the server. The entire office of 4 users is blocked from accessing anything on the web server. A trace route reveals they get all the way to the server before they are blocked. However, they can access a linux server that is a different VM with a different IP on the same physical server. Also, when they are blocked from their office, they can still access the site from their mobile phone or local Starbucks. They can also occasionally reset the router and gain access to the web server again as they are on a dynamic IP address. I checked IIS and allow all IPs to access the server. There is nothing in the logs the says anything about a user being banned. I really have no idea what is causing this? Could it be a virus on their end? I have even moved the SaaS to a completely new server in a different location, and they were working fine for about a month, and then the problem started occurring again. Are there any hidden blacklists in IIS? Or is it a routing issue on their end?

  Read the article

• Debugging nginx URL rewrite: How do I figure out where the problem is?

  - by pjmorse

  I have a specific URL pattern on a site which needs to be redirected to the HTTPS version. This is a Django site; Nginx checks each URL in memcached, and if it doesn't find a cached version it proxies the request to Apache/mod_python for Django to render the page. The relevant configuration block is rewrite ^/certificate https://mysite.com/certificate ; rewrite ^/([a-zA-Z]{2})/certificate https://mysite.com/certificate ; ...and it doesn't appear to be working at all. Nginx is: $ nginx -V nginx version: nginx/0.7.65 built by gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) TLS SNI support disabled configure arguments: --prefix=/usr/local/nginx --pid-path=/var/run/nginx.pid --with-http_gzip_static_module --with-http_ssl_module How can I figure out if the problem is my patterns not matching, or a more obscure configuration problem? (The site is localized to three languages, and the localization is in the URL string, e.g. /US/news/, /DE/about, etc. It tracks localization in the session as well, defaulting to US, so if you just requested /news Django will rewrite to /US/news unless the user has a cookie indicating they're using a different localization. Django handles this, though, not Nginx.)

  Read the article

• How can I tell why I have access to a file share on Windows Server

  - by Joel

  I have a file share on a Windows 2008 R2 server in a AD domain (call it \SECURESERVER\STUFF) and I am not sure if I have the share and folder permissions set up right. I noticed the problem when I set up new server (WORKGROUP\FOREIGNSERVER) that was not joined to the domain and tried to copy some files off of \SECURESERVER\STUFF. I was surprised to find that when I tried to access the files, it did not prompt me for a username and password and proceeded to give me full access to the files. That worried me so I tried the same thing on some workstations that were not in the domain and they did NOT have the same behavior (they did prompt for a username/password as desired/expected). So, I think there is something peculiar about FOREIGNSERVER. I am logging into it with a local admin account, but my domain and SECURESERVER should know nothing of this server. I've carefully gone through the share and folder permissions on the share but I can't find the reason that FOREIGNSERVER has access. How can I find out why FOREIGNSERVER has access to SECURESERVER?

  Read the article

• One workstation gets slow access to the server, but others are fast

  - by Mike Hanson

  I've just setup a machine with Windows Server 2008. It hosts various services, like IIS, POP3, SMTP, Music for Squeezeboxes, VNC. All was working well for the first week or so. One day I needed to create a mapped drive on the server, so it could access files on my workstation. Windows indicated that Network Discovery was needed, so I turned it on with the "Home / Office" option (rather than "Public"). This may be coincidence, but since that time I've been having troubles accessing various services from my main workstation (running Windows 7/64): POP3 continued working correctly, but SMTP was delayed or failed entirely. (Telnet took 20 seconds to connect, but Outlook would never send messages.) VNC failed entirely. I reinstalled it on the server, and now it works but feels sluggish. The music web server was extremely delayed and usually failed. I tried reinstalling, and now it takes about 30 seconds to show the page name on the browser tab, and another 30 seconds to display any page contents. Other machines on the local network seem fine, as do machines connected via the Internet. I don't believe I changed anything on my own machine that would cause this. I considered the possibility that my anti-virus was involved, so I uninstalled AVG (commercial version), but that didn't help. I installed Norton 360 after that, and it didn't complain of viruses on my machine, and the delays remained. Because only my machine is affect, I'm tempted to blame it, except that reinstalling software on the server improved the situation, so there is almost certainly something going on with the server too. The firewall has all the necessary ports open, and it works fine for the other workstations (including external machines connected via the Internet), which indicates that it should be OK. Any ideas?

  Read the article

• gitweb refusing to blame

  - by Slipp D. Thompson

  I'm attempting to get gitweb (git 1.8.4.2, via git instaweb) in a project dir on my Debian server to offer blame views. In my /etc/gitweb.conf: … # default logo, favicon, etc. settings $feature{'blame'}{'default'} = [1]; $feature{'pickaxe'}{'default'} = [1]; $feature{'snapshot'}{'default'} = ['tgz', 'txz', 'zip']; $feature{'highlight'}{'default'} = [1]; $feature{'pathinfo'}{'default'} = [1]; In my global config file: [gitweb] blame = true snapshot = tgz, txz, zip patches = 256 avatar = gravatar [instaweb] local = false httpd = apache2 -f port = 4321 In my project's .git/config file: [gitweb] blame = true And yet, when I try to load a git blame view (via hand-modifying the URL to http://myserversip:4321/?p=.git;a=blame;f=Tests/InchCoordProxyTests.m;h=b4b2…;hb=53b4, since blame action links don't show up): Doing a quick search for “Blame view not allowed” in the gitweb.cgi source reveals plainly that the gitweb_check_feature('blame') conditional is failing. What am I doing wrong? Or, is there a way to verbosely print out why gitweb is doing what it's doing (e.g. which config files were read, which settings were loaded from each file, etc.)?

  Read the article

• disk space keeps filling up on EC2 instance with no apperent files/directories

  - by sasher

  How come os shows 6.5G used but I see only 3.6G in files/directories? Running as root on an Amazon Linux AMI (seems like Centos), lots of free memory available, no swapping going on, no apparent file descriptors issue. The only thing I can think of is a log file that was deleted while applications append to it. Disk space usage is slowly but continuously rising towards full capacity (~1k/min with very small decreases from time to time) Any explanation? Solution? du --max-depth=1 -h / 1.2G /usr 4.0K /cgroup 22M /lib64 11M /sbin 19M /etc 52K /dev 2.1G /var 4.0K /media 0 /sys 4.0K /selinux du: cannot access /proc/14024/task/14024/fd/4': No such file or directory du: cannot access<br/> /proc/14024/task/14024/fdinfo/4': No such file or directory du: cannot access /proc/14024/fd/4': No such file or directory du: cannot<br/> access/proc/14024/fdinfo/4': No such file or directory 0 /proc 18M /home 4.0K /logs 8.1M /bin 16K /lost+found 12M /tmp 4.0K /srv 35M /boot 79M /lib 56K /root 67M /opt 4.0K /local 4.0K /mnt 3.6G / df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 6.5G 1.4G 84% / tmpfs 3.7G 0 3.7G 0% /dev/shm sysctl fs.file-nr fs.file-nr = 864 0 761182

  Read the article

• What is my BaseDN supposed to be with the following configuration of OpenLDAP?

  - by fuzzy lollipop

  I have the following in my OpenLDAP configuration. Using the latest version OpenLDAP on Centos 5.3. Installed using yum. From my /etc/openldap/slapd.conf database bdb suffix "dc=company,dc=com" rootdn "cn=Manager,dc=company,dc=com" From my /etc/openldap/ldap.conf BASE dc=company,dc=com I have successfully added an entry with ldapadd and retrieved it with ldapsearch from a local bash shell on the box. Now I am trying to get a Graphical Editor to connect to this server remotely so I can enter people from my laptop. But I am having no luck. I tried JXplorer, and it connects with Anonymous bind without me having to specify a BaseDN but I can't edit anything that way. If I try and give it a user name and password, using Manager and my rootpw I have in clear text just for testing, every GUI Client on my remote laptop complains about my BaseDN not being the correct format when I enter dc=company,dc=com and I tried cn=Manager,dc=company,dc=com. Error opening connection: [LDAP: error code 34 - invalid DN] I have tried multiple clients and all of them connect as anonymous, none let me connect authenticated where I can actually create or edit anything. I am using Manager as my username and the password from rootpw, is that correct?

  Read the article

• Running WAMP (XAMPP) and LAMP from One SSD, On 64-bit Windows and Linux Machines

  - by nicorellius

  I have an solid state drive that I develop websites on. The reason I do this is because I work on a few different computers. Historically, I created separate developing environments to use for each machine. This was OK, but if the system changed for some reason, eg, new OS install, it was a pain. So I bought a USB 3.0 enclosure and put a solid state drive in there and it's pretty darn fast, which is good. I was working with three Windows machines and I could simply hook up the drive, launch my XAMPP server and away I went, developing websites: using Dreamweaver, Komodo, Notepad++, Eclipse, etc. Recently, however, one of my Windows machines' hard drive went down and instead of going back to Windows in this case, I went with Ububntu 12.04. I have several Ubuntu workstations and servers and I like Linux, so I thought his was a great opportunity to transition. I went to work installing and trying to set up a LAMP server and, besides from XAMPP 64-bit compatibility out of the box, I'm seeing other issues with getting this Linux server running. I will keep trying to resolve this, but in the meantime... my question is, has anyone ever successfully run both WAMP and LAMP from the same SSD (formatted to NTFS)? I'm sure there are lots of barriers to this happening, like local file system, OS libraries, dependencies, etc. But I was thinking it would be cool if it could be done. I'm no expert, so if this is just plain old stupid, please don't hesitate to let me know.

  Read the article

• Packet flooding while configuring a Debian L2TP/IPSec client?

  - by Joseph B.

  I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

  Read the article

< Previous Page | 656 657 658 659 660 661 662 663 664 665 666 667  | Next Page >