Search Results

Search found 8673 results on 347 pages for 'kvm switch'.

Page 67/347 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Windows Server 2008 R2 install reboots unexpectedly during "Completing installation" phase

  - by knda

  I am attempting to install Windows Server 2008 R2 onto a Cisco UCS C201 M2 rack mounted server but am having major difficulties and wondering if anyone has some insight or items they could recommend for me to look at to get this one resolved. Installation is being attempted via the Cisco remote console (using CIMC's Virtual dvd-rom).. following the first phase of Setup where the installation files are copied to the target hard drive, then a reboot occurs to load Setup from the HDD, mid-way in the "Completing Installation" phase the system then reboots unexpectedly. System configuration Cisco UCS C201 M2 (2RU rack mounted server) 16GB RAM, 2x 73GB 15K SAS, 4x 300GB 10k SAS Add-on cards - Intel quad-port GigE card (no fibre channel cards) Storage - LSI MegaRAID SAS 9261-8i. onboard SATA is disabled (no SATA drives connected) KVM - Belkin No physical DVD-ROM.. :( I have... Run memtest86+, no RAM faults Disabled/enabled SATA support (BIOS) Attempted install from USB DVD-ROM, no effect Attempted unattended install scripted via Cisco Configuration Manager DVD provided Removed Belkin KVM in case that was causing drama Discovered that the Cisco website is "awesome" for searching for PDFs/Drivers cough, reverted back to Google Downloaded latest LSI drivers from LSI's site and used during Server 2008 install checked Windows ISO against checksum's from MS site checked Windows ISO by using it for an install in a VM Running out of ways to troubleshoot this as I am not sure how to enable any sort of 'verbose' mode during the setup process. Next step I have planned is to remove the Intel NIC and try the installation again.. Edit: Problem was the "Cisco INTEL QUAD PT GBE" (1000/PT) .. will have to see if this card is faulty or if it's just drivers.. thanks for the help.

  Read the article

• Black screen when switching users on HP laptop (running vista)

  - by davepreston

  Vista machine: When I switch users I get a black screen for 30+ seconds. Doesn't seem to matter who is logged in. Delay happens when I click "switch user" but not when I lock the screen and log back in as same user. Specs: Windows Vista 64-bit; HP pavilion dv9710t laptop; 17" screen (best guess is that it has something to do with display settings, not sure)

  Read the article

• Turn off antialiasing in emacs 23 in MS Windows XP

  - by ntzanos

  Hello, I managed to turn off antialiasing for the default font. The thing is that when I switch to typing greek characters, although the same font is used it appears antialiased. Is there any way to switch off antialiasing for greek characters as well?

  Read the article

• How can I run the same Linux Installation on my hardware and in a virtual machine?

  - by LithMaster

  I've started some development that requires Linux (I'm currently on Ubuntu, but I may switch to Debian), but I still use Windows 7 for my day-to-day computing. I have already tried a dual-boot setup, but I've found that it is too cumbersome to switch between Linux and Windows. I'm wondering if it's possible to setup an installation of Linux (again, Ubuntu or Debian) on a partition of my hard drive that I can also run from Windows in a virtualized environment.

  Read the article

• Ethernet: network topology

  - by aix

  Consider a standard GigE network switch. In order to do the switching, presumably it needs to maintain a map of MAC addresses of all things that exist on the network to its (switch's) port numbers. How does it maintain such a map? What are the protocols involved? If I change the topology of one part of the network, does the entire network get notified or do things get discovered "lazily" (i.e. on first need)?

  Read the article

• How OS manage running programs

  - by Vit

  Hi, since windows is multitasking OS, it must somehow switch between processes. But how is it done? Does windows include some kind of breakpoints into running programs, which should switch to other process? Becouse when program is executed, it takes control of CPU. So to enable multitasking OS must include some break instruction into the program. Am I right?

  Read the article

• Home Network Speed Control

  - by DanSpd

  I have a home network installed in following way: Internet<-server<-switch<-computers,etc Server has DHCP server installed and I would like to be able to limit download&upload speed for each client connected to server via switch. Anyone can suggest good free software to do that? Thanks

  Read the article

• Vmware - How do i config a host-only network

  - by nXqd

  The understanding about Host-only: I use VMware 7, Vmnet1 is the host-only adapter for host and it's IP is 192.168.209.1 . I'm really confused about this , does it connect to Vmnet 1 switch and Vmnet has DHCP also, it provieds IP range: Why it has virtual host adapter ( Vmnet 1) has IP which isn't in range while it's just an adapter in virtual network, it connects through switch Vmnet like the guest adapter Waiting for your answers , thanks in advance :)

  Read the article

• controlling how UltraVNC handles ALT+TAB

  - by Michael

  Most of the time it ignores it and I am able to switch away from UltraVNC to another application. I like this behavior. However, occasionally it gets into a mode where - for no discernable reason - it passes the Alt+Tab to the remote host which is incredibly annoying as I am used to the other behavior and suddenly I have no keyboard shortcut to switch to a different local windows. Since it appears to exhibit both behaviors, I assume there is some way to control which behavior is in use, but I haven't been able to find it

  Read the article

• IPod Touch - Refreshing Web Page while Offline?

  - by Anduril66

  Using my home wifi network, I open several browser windows on my Ipod Touch and load different web pages on them so I can read them on the bus later. Often, I can switch between windows and read the pages while WiFi is turned off but occasionally web pages try to refresh themselves when I switch to them. Why is this?

  Read the article

• Can I stop the Google talk client checking my gmail?

  - by izb

  I want to use Google talk, but I don't want it checking my email and notifying me of new mail all the time. I can't see how to switch it off, but it seems like the sort of thing that should be an option. Am I missing something? How can I switch email support off?

  Read the article

• Libvirt / QEmu Machine Fails and Refuses Restart Because of Memory Allocation Errors

  - by Elmar Weber

  I'm having a problem with libvirt. On a system restart all virtual machines (VMs) are started without a problem and keep running. Then at some point in time a set of machines shuts down according to their log. When I try to restart the machine, I'm getting an error that the memory allocation failed, although more than enough memory is free. server ~ # free total used free shared buffers cached Mem: 16176648 16025476 151172 0 285432 950300 -/+ buffers/cache: 14789744 1386904 Swap: 0 0 0 server ~ # virsh start zimbra error: Failed to start domain zimbra error: Unable to read from monitor: Connection reset by peer server ~ # tail -n 4 /var/log/libvirt/qemu/zimbra.log LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 3072 -smp 2,sockets=2,cores=1,threads=1 -name zimbra -uuid d05ddb7a-83c4-a77b-d8bc-a322648520cf -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/zimbra.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -drive file=/var/lib/libvirt/images/zimbra.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0,bootindex=1 -netdev tap,fd=19,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=52:54:00:21:a9:ad,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 192.168.1.2:25 -k de -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/2 Failed to allocate 3221225472 B: Cannot allocate memory 2012-07-06 08:42:56.076+0000: shutting down server ~ # uname -a Linux server 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux The system is a Ubuntu 12.04 server. The problem seems to occurs since the last restart, which was due to a number of package upgrades and a kernel upgrade. I tried booting with the previous kernel, the problem persists. I was not able to pinpoint an exact event when the machines fail, they do it at nearly the same time. The last time a duplicity job was running, this was not always the case however. Any suggestions on how to debug this? Best regards, elm

  Read the article

• Virtualbox: prevent a virtual machine to go down after I log out from the consolle I lanched the VM from

  - by Daniele

  I login remotely to a machine with Virtualbox installed by launching: ssh -Y root@virtualbox After that, I launch a Virtual Machine: nohup VBoxSDL --startvm vm1 or nohup VBoxSDL --startvm vm1 & After that, I don't have the prompt anymore. Then, if I switch off my local machine, the virtual machine goes down (no matter whether I use & or not). How can I keep it running after I switch off my local machine?

  Read the article

• Home Server: cpu virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on VM (or compute instance) management and what would best suit my needs. (I have another question related to the storage management). My use cases are: A backup server: rsync and other services running. A personal cloud server: a kind of owned dropbox system, à la ownCloud. " users foreseen. A media server: streaming videos and displaying photos. Here my environement and wishes: Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine 2-3 VMs foreseen: backup server, owncloud server and media server (optional). Those are only servers, so no graphical console needed (I don't need VirtualBox) By VM I mean a virtualised environment like KVM, Xen, etc. or a compute instance like with OpenStack storage should be "virtualised/cloudified" see my other question. VM should be able to be migrated to another server in the future if performance cannot be fullfilled anymore by the current server It does not matter if installation of such setup is complicated as long as management tools allow for easy maintenance I don't have Windows at home, so solution should be Linux friendly and would be nice to be web based. But native apps are OK too. System should be easy to enhance: by adding a new server to migate some of the VMs to it. So it's really a kind of private cloud on which I could run some Linux OS. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. So Xen, KVM, VitualBox or OpenStack? What would you recommend?

  Read the article

• how to disable all system sounds - permanently

  - by studiohack

  I prefer the sound scheme of Windows 7 HP to be set to "No Sounds" ALL the time. The problem is, when I switch themes, the themes switch sound schemes also. I know I can go in and disable/change to "No Sounds" every time by hand, but is there a way to turn it off and keep it off, regardless of the theme? Thanks!

  Read the article

• How to configure networking on an appliance such that it can plug and play on any corporate network?

  - by Joshua Lim

  I had a chance to configure a Moxa NPort device server appliance on my client's network, it was very easy to do so, done in just 2 minutes. Here's what I did:- The Moxa device server had a preset IP address of 192.168.127.254 and subnet mask 255.255.255.0 - http://www.moxa.com/doc/manual/nport/5400/NPort_5400_Series_Users_Manual_v4.pdf Moxa provides a Windows software which I used to "scan" for the device server. It worked like magic! The software returns a list of device servers found. Each device server is identified by MAC address, and by selecting the device server using the software, I can reset the default IP address and subnet mask of that device server! In comparison, during an earlier project, I spent 2 hours trying to get KVM to work for a Windows 7 embedded appliance I'm trying to install in my client's network - http://superuser.com/questions/380305/how-to-configure-windows-7-professional-appliance-pc-on-my-clients-network-usin Prior to that, I have already tried pre-configuring the IP address and subnet mask to the one which my client provided, yet the appliance still can't connect to the client's network! I've also tried cross cable, didn't work either. After KVM worked, I discovered that the network settings were "lost" after I plug the machine into the client's network. Now my question is what can I do to setup my Windows 7 embedded appliance so that it can connect to any network like that the Moxa device server? I tried experimenting this on my network using a Windows machine configured to an IP address of 192.168.127.254 and subnet mask 255.255.255.0, but it doesn't connect to my network that uses 192.168.0.*. :( EDIT: I would like to point out that the Moxa Windows configuration software seems to be able to connect to any Moxa device connected to the network even if it is on a different subnet, as long as the network adapter shows "connected". This is important because the Moxa device has no VGSM port or interface to configure the IP address.

  Read the article

• Automatic layout of manual network mapping

  - by Paul

  So I have a small business network mainly consisting of two routed layer-2 domains with a total of ca. 100 devices spread over ca. 2000m² production and office spaces. Typical problems to solve using the graph would be: Over what (cable) path is a PC connected to the server? Where to expect devices connected to a switch port? I want to generate a graph of the physical network topology: Nodes are endpoint devices, switch ports, wall outlets, patch panel ports etc. Edges are cable connections. Ideally, grouping edges (or segments) that pass through the same bundle could be grouped. Also I would like to augment the graph data with automatically gathered data (monitoring state, MAC address, Switch port <- MAC entries to build up parts of the map). At the moment I use graphviz for this inside a Confluence wiki like that: layout = "neato" overlap = scale subgraph { rankdir = "TB" subgraph cluster_r1pf1 { r1pf1 [label="{ Rack 1 PF 1 | { <p1>P1 | <p2>P2 | <p3>P3} }", shape=record] } subgraph cluster_switch1 { switch1 [label="{ Rack 1 Switch 1 | { <p1> P1 | <p1> P1 | <p3> P3} }", shape=record] } r1pf1:p1 -> switch1:p1 (obviously there are dozens of entries omitted here) Problem is: I have a hard time to influence graphviz to generate a bearable layout. Edges overlap so bad that you can't read the diagram anymore. The question is: What other tools (be it interactive like Visio, Omnigraffle or I/O-oriented like graphviz) exist that would allow an easily versionable (as in: Operates on a text file) documentation that is both machine and human readable and editable? Why not OmniGraffle or Visio? Well we don't have Macs and Visio is not available at the moment. To buy it I would need good arguments. Automation would be one of that. But last time I looked, versioning Visio files or even thinking about automatic handling was a nightmare. Related: Network Mapping Tools basically asks the same with a focus on generating the complete graph automatically (but without the need to document cabling connections) Recommendations for automatic computer inventory brings up links of "all-in-one" solutions

  Read the article

• Using AutoHotKey to change audio output source?

  - by Scott

  I have two primary audio outputs on my machine: The speakers and a USB headset. Currently, in Windows 7 Professional x64, I type "sound" in the Start search menu to open up this dialog: I only care about the top two options for the purposes of this question. I would like to know if there's a way in AutoHotKey to switch from "Speakers (4- Sennheiser USB Headset)" to "Speakers (VIA High Definition Audio)" so I can avoid having to open this dialog every time I wish to switch. Thanks!

  Read the article

• How do I keep a bridge enabled on a bonded interface?

  - by jlawer

  I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

  Read the article

• Live screen annotation?

  - by TreyK

  Hey all, I'm in need of some software that will allow me to make annotations on the screen to ease the frustration of using a piece of low-quality software to verify some data. I've tried a few programs out, but so far none of them have one essential feature: I must be able to switch between the annotation software and the program without losing the annotations that I've previously made. Every program so far has cleared my annotations when I switch out and then back in to it. Running Windows XP. Thanks for any help,

  Read the article

• Easy management of multiple connections

  - by pistacchio

  Hi, on a Windows 7 machine I need to switch back and forth two connections: the LAN connection (that works behind a proxy) and a wireless connection via a USB modem. This requires every time to activate / deactivate two connections in the manager and switch on / off the LAN settings. I don't think there is some way to keep two connections alive and specify which one to use based on the program, but my question is: is there a simple little utility that makes switching the connection one-click easy and fast? Thanks

  Read the article

• Two monitors with Mac Mini - one displays black despite receiving a signal

  - by alex

  My Mac Mini outputs to my two new monitors - Dell U2311Hs. The LED on the bezel displays blue when receiving a signal, or yellow otherwise. Both screens are displaying blue. It also seems my Mini can see both of them... However, one of them is black. It just displays black, but appears to be receiving a signal (when I turn the Mac off, it then displays No Signal). To make things weirder, on startup, the boot up (white with Apple logo) appears on the right monitor (the one that now displays black). Occasionally, it flickers up on the black screen for 1 second. I have tried Detect Displays. It appears to do nothing. I'm also running a dual monitor KVM. Video connections are DVI-D. How can I fix this situation? Thanks. Update This is the weirdest thing - I used the DVI-D cable that came with the KVM and it seems to have fixed it - I didn't both because it looks identical to any other DVI cable (in form an pin out). So, I will accept an answer if someone can tell me what may be the difference in these cables?

  Read the article

• Best way to build / implement a corporate developer Linux distro with multiple kernels?

  - by Garen

  At work we have Linux users who understandably prefer using Ubuntu. Problem is, we also have developer tools that only work with 'officially' supported Linux distributions that use much older 2.6.18 based kernels. (And even if they worked with newer ones, the vendors could always say they won't "support" the software unless it's on one of their 'officially' supported platforms.) We could of course just tell them to use CentOS or something else 2.6.18-based, and I'm sure their response would be something like: "you can take Ubuntu from our cold, dead hands." :) Which brings to me some questions--is there any good/easy/recommended way to run something like Ubuntu as a host VM and Centos 5.x as a guest OS (with which system--Xen,KVM,VMWare, ...?), and then roll that into our own custom internal distribution that could be easily installed? KVM looks like a good high-performance option just recently included in RHEL 5.4, but if hardware support for virtualization like Intel-VT or AMD-V is necessary, then I'd guess only those folks with fairly new PCs will be able to do it. Would be very interested to hear how anyone else has addressed this kind issue. EDIT: The target audience / users of this kind of system would be developers, each one needs to run locally licensed commercial software, so building out some separate beefy central machines isn't an option unfortunately due to license restrictions. Even if that weren't the case, a couple developers could quickly eat up the resources with parallel builds. :) Ideally, I was hoping there was some step-by-step guide out there to build your own pre-built distribution that had e.g. CentOS 5.x and Ubuntu Desktop as a guest.

  Read the article

• Buffer requests in nginx while a symlink switches on backend

  - by Quintin Par

  In a release deployment I would like to buffer client requests that come to nginx(in reverse proxy) mode to be buffered for possibily 1-2 seconds while a pdsh request is sent to switch symlinks on the back end server to /var/www/html/current . After the switch is complete, I would want to release the buffering while avoiding a herd clash. Is this possible in nginx? Can someone help? Edit: The idea is not to loose requests and from nginx forums I've come to know that retries can sometimes results in CPU spins

  Read the article

• Switching keyboard layout in Windows globally

  - by Manuel Faux

  I'm searching for a solution to switch my keyboard layout in Windows globally for all windows quickly. When I switch the current layout by pressing the magic combination Alt+Shift or when I choose another layout in the language bar, this only changes the layout in the current window.

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >