Search Results

Search found 2195 results on 88 pages for 'mit scheme'.

Page 67/88 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Fan not working on thinkpad L430, laptop overheating

  - by Dirk B.

  I'm having problems controlling the fan of my Lenovo Thinkpad L430. The fan doesn't start. Without any fan control installed the fan just doesn't run. If I run stress, it does run a little, but it's nowhere near the speed it should be. After a while, the laptop just overheats and stops. I Tried to install tp-fancontrol, and enabled thinkpad_acpi fancontrol=1, but to no avail. If I try to set the fan speed manually, it doesn't start up. In windows, there's a program called TPFanControl. It turns out that this laptop uses a different scheme to control the fan than other thinkpads. The level runs from 0 to 255, and max = 0 and min=255. Now I'm looking for a fan control program that works for linux. Does anyone know if it actually exists? Anyone with any experience on fan control on a L430? Update: sudo pwmconfig gives the following output: # pwmconfig revision 5857 (2010-08-22) This program will search your sensors for pulse width modulation (pwm) controls, and test each one to see if it controls a fan on your motherboard. Note that many motherboards do not have pwm circuitry installed, even if your sensor chip supports pwm. We will attempt to briefly stop each fan using the pwm controls. The program will attempt to restore each fan to full speed after testing. However, it is ** very important ** that you physically verify that the fans have been to full speed after the program has completed. Found the following devices: hwmon0 is acpitz hwmon1/device is coretemp hwmon2/device is thinkpad Found the following PWM controls: hwmon2/device/pwm1 hwmon2/device/pwm1 is currently setup for automatic speed control. In general, automatic mode is preferred over manual mode, as it is more efficient and it reacts faster. Are you sure that you want to setup this output for manual control? (n) y Giving the fans some time to reach full speed... Found the following fan sensors: hwmon2/device/fan1_input current speed: 0 ... skipping! There are no working fan sensors, all readings are 0. Make sure you have a 3-wire fan connected. You may also need to increase the fan divisors. See doc/fan-divisors for more information. regards, Dirk

  Read the article

• ESB Toolkit 2.0 EndPointConfig (HTTPS with WCF-BasicHttp and the ESB Toolkit 2.0)

  - by Andy Morrison

  Earlier this week I had an ESB endpoint (Off-Ramp in ESB parlance) that I was sending to over http using WCF-BasicHttp.  I needed to switch the protocol to https: which I did by changing my UDDI Binding over to https:  No problem from a management perspective; however, when I tried to run the process I saw this exception: Event Type:                     Error Event Source:                BizTalk Server 2009 Event Category:            BizTalk Server 2009 Event ID:   5754 Date:                                    3/10/2010 Time:                                   2:58:23 PM User:                                    N/A Computer:                       XXXXXXXXX Description: A message sent to adapter "WCF-BasicHttp" on send port "SPDynamic.XXX.SR" with URI "https://XXXXXXXXX.com/XXXXXXX/whatever.asmx" is suspended.  Error details: System.ArgumentException: The provided URI scheme 'https' is invalid; expected 'http'. Parameter name: via    at System.ServiceModel.Channels.TransportChannelFactory`1.ValidateScheme(Uri via)    at System.ServiceModel.Channels.HttpChannelFactory.ValidateCreateChannelParameters(EndpointAddress remoteAddress, Uri via)    at System.ServiceModel.Channels.HttpChannelFactory.OnCreateChannel(EndpointAddress remoteAddress, Uri via)    at System.ServiceModel.Channels.ChannelFactoryBase`1.InternalCreateChannel(EndpointAddress address, Uri via)    at System.ServiceModel.Channels.ChannelFactoryBase`1.CreateChannel(EndpointAddress address, Uri via)    at System.ServiceModel.Channels.ServiceChannelFactory.ServiceChannelFactoryOverRequest.CreateInnerChannelBinder(EndpointAddress to, Uri via)    at System.ServiceModel.Channels.ServiceChannelFactory.CreateServiceChannel(EndpointAddress address, Uri via)    at System.ServiceModel.Channels.ServiceChannelFactory.CreateChannel(Type channelType, EndpointAddress address, Uri via)    at System.ServiceModel.ChannelFactory`1.CreateChannel(EndpointAddress address, Uri via)    at System.ServiceModel.ChannelFactory`1.CreateChannel()    at Microsoft.BizTalk.Adapter.Wcf.Runtime.WcfClient`2.GetChannel[TChannel](IBaseMessage bizTalkMessage, ChannelFactory`1& cachedFactory)    at Microsoft.BizTalk.Adapter.Wcf.Runtime.WcfClient`2.SendMessage(IBaseMessage bizTalkMessage)  MessageId:  {1170F4ED-550F-4F7E-B0E0-1EE92A25AB10}  InstanceID: {1640C6C6-CA9C-4746-AEB0-584FDF7BB61E} I knew from a previous experience that I likely needed to set the SecurityMode setting for my Send Port.  But how do you do this for a Dynamic port (which I was using since this is an ESB solution)? Within the UDDI portal you have to add an additional Instance Info to your Binding named: EndPointConfig  Then you have to set its value to:  SecurityMode=Transport Like this:    The EndPointConfig is how the ESB Toolkit 2.0 provides extensibility for the various transports.  To see what the key-value pair options are for a given transport, open up an itinerary and change one of your resolvers to a “static” resolver by setting the “Resolver Implementation” to Static.  Then select a “Transport Name” ”, for instance to WCF-BasicHttp.  At this point you can then click on the “EndPoint Configuration” property for to see an adapter/ramp specific properties dialog (key-value pairs.)    Here’s the dialog that popped up for WCF-BasicHttp:   I simply set the SecurityMode to Transport.  Please note that you will get different properties within the window depending on the Transport Name you select for the resolver. When you are done with your settings, export the itinerary to disk and find that xml; then find that resolver’s xml within that file.  It will look like endpointConfig=SecurityMode=Transport in this case.  Note that if you set additional properties you will have additional key-value pairs after endpointConfig= Copy that string and paste it into the UDDI portal for you Binding’s EndPointConfig Instance Info value.

  Read the article

• Sixeyed.Caching available now on NuGet and GitHub!

  - by Elton Stoneman

  Originally posted on: http://geekswithblogs.net/EltonStoneman/archive/2013/10/22/sixeyed.caching-available-now-on-nuget-and-github.aspxThe good guys at Pluralsight have okayed me to publish my caching framework (as seen in Caching in the .NET Stack: Inside-Out) as an open-source library, and it’s out now. You can get it here: Sixeyed.Caching source code on GitHub, and here: Sixeyed.Caching package v1.0.0 on NuGet. If you haven’t seen the course, there’s a preview here on YouTube: In-Process and Out-of-Process Caches, which gives a good flavour. The library is a wrapper around various cache providers, including the .NET MemoryCache, AppFabric cache, and  memcached*. All the wrappers inherit from a base class which gives you a set of common functionality against all the cache implementations: •    inherits OutputCacheProvider, so you can use your chosen cache provider as an ASP.NET output cache; •    serialization and encryption, so you can configure whether you want your cache items serialized (XML, JSON or binary) and encrypted; •    instrumentation, you can optionally use performance counters to monitor cache attempts and hits, at a low level. The framework wraps up different caches into an ICache interface, and it lets you use a provider directly like this: Cache.Memory.Get<RefData>(refDataKey); - or with configuration to use the default cache provider: Cache.Default.Get<RefData>(refDataKey); The library uses Unity’s interception framework to implement AOP caching, which you can use by flagging methods with the [Cache] attribute: [Cache] public RefData GetItem(string refDataKey) - and you can be more specific on the required cache behaviour: [Cache(CacheType=CacheType.Memory, Days=1] public RefData GetItem(string refDataKey) - or really specific: [Cache(CacheType=CacheType.Disk, SerializationFormat=SerializationFormat.Json, Hours=2, Minutes=59)] public RefData GetItem(string refDataKey) Provided you get instances of classes with cacheable methods from the container, the attributed method results will be cached, and repeated calls will be fetched from the cache. You can also set a bunch of cache defaults in application config, like whether to use encryption and instrumentation, and whether the cache system is enabled at all: <sixeyed.caching enabled="true"> <performanceCounters instrumentCacheTotalCounts="true" instrumentCacheTargetCounts="true" categoryNamePrefix ="Sixeyed.Caching.Tests"/> <encryption enabled="true" key="1234567890abcdef1234567890abcdef" iv="1234567890abcdef"/> <!-- key must be 32 characters, IV must be 16 characters--> </sixeyed.caching> For AOP and methods flagged with the cache attribute, you can override the compile-time cache settings at runtime with more config (keyed by the class and method name): <sixeyed.caching enabled="true"> <targets> <target keyPrefix="MethodLevelCachingStub.GetRandomIntCacheConfiguredInternal" enabled="false"/> <target keyPrefix="MethodLevelCachingStub.GetRandomIntCacheExpiresConfiguredInternal" seconds="1"/> </targets> It’s released under the MIT license, so you can use it freely in your own apps and modify as required. I’ll be adding more content to the GitHub wiki, which will be the main source of documentation, but for now there’s an FAQ to get you started. * - in the course the framework library also wraps NCache Express, but there's no public redistributable library that I can find, so it's not in Sixeyed.Caching.

  Read the article

• Lenovo Thinkpad L430 overheating due to fan problems

  - by Dirk B.

  This is the same question as Fan not working on thinkpad L430, laptop overheating, but that question has been marked as a duplicate, which it is not, and I cannot reopen it. I'm having problems controlling the fan of my Lenovo Thinkpad L430. The fan doesn't start. Without any fan control installed the fan just doesn't run. If I run stress, it does run a little, but it's nowhere near the speed it should be. After a while, the laptop just overheats and stops. I Tried to install tp-fancontrol, and enabled thinkpad_acpi fancontrol=1, but to no avail. If I try to set the fan speed manually, it doesn't start up. In windows, there's a program called TPFanControl. It turns out that this laptop uses a different scheme to control the fan than other thinkpads. The level runs from 0 to 255, and max = 0 and min=255. Now I'm looking for a fan control program that works for linux. Does anyone know if it actually exists? Anyone with any experience on fan control on a L430? Update: sudo pwmconfig gives the following output: # pwmconfig revision 5857 (2010-08-22) This program will search your sensors for pulse width modulation (pwm) controls, and test each one to see if it controls a fan on your motherboard. Note that many motherboards do not have pwm circuitry installed, even if your sensor chip supports pwm. We will attempt to briefly stop each fan using the pwm controls. The program will attempt to restore each fan to full speed after testing. However, it is ** very important ** that you physically verify that the fans have been to full speed after the program has completed. Found the following devices: hwmon0 is acpitz hwmon1/device is coretemp hwmon2/device is thinkpad Found the following PWM controls: hwmon2/device/pwm1 hwmon2/device/pwm1 is currently setup for automatic speed control. In general, automatic mode is preferred over manual mode, as it is more efficient and it reacts faster. Are you sure that you want to setup this output for manual control? (n) y Giving the fans some time to reach full speed... Found the following fan sensors: hwmon2/device/fan1_input current speed: 0 ... skipping! There are no working fan sensors, all readings are 0. Make sure you have a 3-wire fan connected. You may also need to increase the fan divisors. See doc/fan-divisors for more information. update: If you need it, lspci is available here

  Read the article

• Silverlight Death Trolls Dancing on XAML&rsquo;s Grave

  - by D'Arcy Lussier

  I’m starting to see a whole bunch of tweets and blog posts on how Silverlight/WPF is dead, or how the XAML team has been disbanded at Microsoft, or how someone predicted Silverlight would die, blah blah blah. They all have a similar ring to it though: “Told ya so!” “They were stupid ideas anyway!” “Serves Microsoft right, boy are they dumb!” Let me tell you something, all those that are gleefully raving about Silverlight/WPF’s demise are nothing more than death trolls. Let’s assume that everything out there is true. Microsoft is obviously moving towards HTML 5 in a huge way (TechCrunch pointed out that SkyDrive has replaced its Silverlight based version with an HTML 5 one), and not just on the web as we’ve seen with recent announcements about how HTML 5 apps will be natively supported on Windows 8. WPF never caught on in the marketplace, regardless of its superior technology offering to Winforms. And Silverlight…well, it gave Flash a good run for its money, but plug-in based web applications are becoming passé in light of HTML 5. (It’s interesting that at a developer conference I put on just a few weeks ago, only 1 out of 60+ sessions included Silverlight. 5 focussed on HTML 5.) So what does this *death* of Silverlight/WPF/XAML mean then in the grand scheme of things (again, assuming that they truly *are* dying/dead)? Well, nothing really…at least nothing bad. Silverlight has given us some fantastic applications and experiences (Vancouver Olympics anyone?), and WP7 couldn’t have launched without Silverlight as its development platform. And WPF, although it had putrid adoption, has had some great success stories. A Canadian company that I talked to recently showed me how they re-wrote their point-of-sale application entirely in WPF, and the product is a huge success providing features their competitors aren’t. Arguably (and I say that only because I know I’m going to get WTF comments for this), VS.NET 2010 is a great example of what a WPF app can provide over previous C++ based applications. Technologies evolve. In a decade we’ve had 5 versions of the .NET framework, seen languages like J# come and go, seen F# appear, see communications layers change with WCF, seen EF go through multiple evolutions and traditional ADO.NET Datasets go extinct (from actual use anyway), and ASP.NET Webforms be replaced with ASP.NET MVC as a preferred web platform. Is Silverlight and WPF done? Maybe…probably?…thing is, it doesn’t really affect me personally in any way, or you…so why would we care if its gets replaced with something better and more robust that we can build better solutions with? Just remember the golden rule: don’t feed the trolls.

  Read the article

• Show raw Text Code from a URL with CodePaste.NET

  - by Rick Strahl

  I introduced CodePaste.NET more than 2 years ago. In case you haven't checked it out it's a code-sharing site where you can post some code, assign a title and syntax scheme to it and then share it with others via a short URL. The idea is super simple and it's not the first time this has been done, but it's focused on Microsoft languages and caters to that crowd. Show your own code from the Web There's another feature that I tweeted about recently that's been there for some time, but is not used very much: CodePaste.NET has the ability to show raw text based code from a URL on the Web in syntax colored format for any of the formats provided. I use this all the time with code links to my Subversion repository which only displays code as plain text. Using CodePaste.NET allows me to show syntax colored versions of the same code. For example I can go from this URL: http://www.west-wind.com:8080/svn/WestwindWebToolkit/trunk/Westwind.Utilities/SupportClasses/PropertyBag.cs To a nicely colored source code view at this Url: http://codepaste.net/ShowUrl?url=http%3A%2F%2Fwww.west-wind.com%3A8080%2Fsvn%2FWestwindWebToolkit%2Ftrunk%2FWestwind.Utilities%2FSupportClasses%2FPropertyBag.cs&Language=C%23 which looks like this:   Use the Form or access URLs directly To get there navigate to the Web Code icon on the CodePaste.NET site and paste your original URL and select a language to display: The form creates a link shown above which has two query string parameters: url - The URL for the raw text on the Web language -  The code language used for syntax highlighting Note that parameters must be URL encoded to work especially the # in C# because otherwise the # will be interpreted by the browser as a hash tag to jump to in the target URL. The URL must be Web accessible so that CodePaste can download it and then apply the syntax coloring. It doesn't work with localhost urls for example. The code returned must be returned in plain text - HTML based text doesn't work. Hope some of you find this a useful feature. Enjoy…© Rick Strahl, West Wind Technologies, 2005-2011Posted in .NET   Tweet (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• StackWrap4J Java wrapper

  - by Bill the Lizard

  The StackWrap4J 1.0.1 jar is now available! (See the changelog) Sample Code / Screen Shot The following code snippet was used to test the wrapper in the Android emulator: TextView text = (TextView)findViewById(R.id.output); StackWrapper stackWrap = new StackOverflow(); String displayText = null; try { Stats stats = stackWrap.getStats(); displayText = "Stack Overflow Statistics"; displayText += "\nTotal Questions: " + stats.getTotalQuestions(); displayText += "\nTotal Unanswered: " + stats.getTotalUnanswered(); displayText += "\nTotal Answers: " + stats.getTotalAnswers(); displayText += "\nTotal Comments: " + stats.getTotalComments(); displayText += "\nTotal Votes: " + stats.getTotalVotes(); displayText += "\nTotal Users: " + stats.getTotalUsers(); } catch(Exception e){ displayText = e.getMessage(); } text.setText(displayText); About StackWrap4J is a Java wrapper for the Stack Exchange API. It is designed to be easy to use, and intuitive to learn while providing the full functionality of the API. License StackWrap4J is available under the MIT license. Download StackWrap4J Platform StackWrap4J was built using Java 1.5 and tested on Sun's JVM. It should run on any implementation of the JVM (1.5 or later). It's also been tested on the Android emulator. It also runs under the Google App Engine. Code You can download the code from our SVN repository hosted on SourceForge. Documentation for the code is also available on the SourceForge site. Authors Bill Cruise Justin Nelson Contact Please feel free to leave feedback here in the Answers section or on the StackWrap4J project discussion forum. Alternatively: Bill is available at: lizard.bill (at) gmail.com Justin can be reached at: jjnguy13 (at) gmail.com Future Currently we are focusing on adding more tests and fixing bugs. We are also working on adding serialization so that our objects can be easily persisted, and throttling so that users of our library don't have to worry about breaking the terms of use of the API. Notes The latest build was tested against version 1.0 of the API on July 28th.

  Read the article

• Evolution Of High Definition TV Viewing

  - by Gopinath

  The following guest post is written by Rob, who is also blogging on entertainment technology topics on iwantsky.com Gone are the days when you need to squint to be able to see the emotions on the faces of Humphrey Bogart and Ingrid Bergman as the lovers bid each other adieu in the classic film Casablanca. These days, watching an ordinary ant painstakingly carry a leaf in Animal Planet can be an exhilarating experience as you get to see not only the slightest movement but also the demarcation line between the insect’s head, thorax and abdomen. The crystal clear imagery was made possible by the sharp minds and the tinkering hands of the scientists that have designed the modern world’s HDTV. What is HDTV and what makes people so agog to have this new innovation in TV watching? HDTV stands for High Definition TV. Television viewing has indeed made a big leap. From the grainy black and whites, TV viewing had moved to colored TVs, progressed to SD TVs and now to HDTV. HDTV is the emerging trend in TV viewing as it delivers bigger and clearer pictures and better audio. Viewers can have a cinema-like TV viewing experience right in the comforts of their own home. With HDTV the viewer is allowed to have a better viewing range. With Standard (SD) TV, the viewer has to be at a distance that is from 3 to 6 times the size of the screen. HDTV allows the viewer to enjoy sharper and clearer images as it is possible to sit at a distance that is 1.5 or 3 times the size of the screen without noticing any image pixilation. Although HDTV appears to be a fairly new innovation, this system has actually existed in various forms years ago. Development of the HDTV was started in Europe as early as 1940s. However, the NTSC and the PAL/SECAM, the two analog TV standards became dominant and became popular worldwide. The analog TV was replaced by the digital TV platform in the 1990s. Even during the analog era, attempts have been made to develop HDTV. Japan has come out with MUSE system. However, due to channel bandwidth requirement concerns, the program was shelved. The entry of four organizations into the HDTV market spurred the development of a beneficial coalition. The AT&T, ATRC, MIT and Zenith HDTV combined forces. In 1993, a Grand Alliance was formed. This group is composed of researchers and HDTV manufacturers. A common standard for the broadcast system of HDTV was developed. In 1995, the system was tested and found successful. With the higher screen resolution of HDTV, viewing has never been more enjoyable. [Image courtesy: samsung] This article titled,Evolution Of High Definition TV Viewing, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• Ubuntu 14.04 Failed to load module udlfb

  - by jar276705

  DisplayLink doesn't load and run. The adapter is recognized and /dev/FB1 is created. USB bus info: Bus 001 Device 006: ID 17e9:0198 DisplayLink Xorg.0.log: X.Org X Server 1.15.1 Release Date: 2014-04-13 [ 44708.386] X Protocol Version 11, Revision 0 [ 44708.389] Build Operating System: Linux 3.2.0-37-generic i686 Ubuntu [ 44708.392] Current Operating System: Linux rrl 3.13.0-24-generic #46-Ubuntu SMP Thu Apr 10 19:08:14 UTC 2014 i686 [ 44708.392] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.13.0-24-generic root=UUID=6b719a77-29e0-4668-8f16-57d0d3a73a3f ro quiet splash vt.handoff=7 [ 44708.399] Build Date: 16 April 2014 01:40:08PM [ 44708.402] xorg-server 2:1.15.1-0ubuntu2 (For technical support please see http://www.ubuntu.com/support) [ 44708.405] Current version of pixman: 0.30.2 [ 44708.412] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 44708.412] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 44708.427] (==) Log file: "/var/log/Xorg.0.log", Time: Thu May 1 09:38:27 2014 [ 44708.431] (==) Using config file: "/etc/X11/xorg.conf" [ 44708.434] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 44708.435] (==) ServerLayout "X.org Configured" [ 44708.435] (**) |-->Screen "DisplayLinkScreen" (0) [ 44708.435] (**) | |-->Monitor "DisplayLinkMonitor" [ 44708.435] (**) | |-->Device "DisplayLinkDevice" [ 44708.435] (**) |-->Screen "Screen0" (1) [ 44708.435] (**) | |-->Monitor "Monitor0" [ 44708.435] (**) | |-->Device "Card0" [ 44708.435] (**) |-->Input Device "Mouse0" [ 44708.435] (**) |-->Input Device "Keyboard0" [ 44708.435] (==) Automatically adding devices [ 44708.435] (==) Automatically enabling devices [ 44708.435] (==) Automatically adding GPU devices [ 44708.435] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 44708.435] Entry deleted from font path. [ 44708.435] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist. [ 44708.435] Entry deleted from font path. [ 44708.435] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist. [ 44708.435] Entry deleted from font path. [ 44708.435] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 44708.435] Entry deleted from font path. [ 44708.435] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist. [ 44708.435] Entry deleted from font path. [ 44708.435] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist. [ 44708.435] Entry deleted from font path. [ 44708.435] (**) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/100dpi/:unscaled, /usr/share/fonts/X11/Type1, /usr/share/fonts/X11/100dpi, built-ins, /usr/share/fonts/X11/misc, /usr/share/fonts/X11/100dpi/:unscaled, /usr/share/fonts/X11/Type1, /usr/share/fonts/X11/100dpi, built-ins [ 44708.435] (**) ModulePath set to "/usr/lib/xorg/modules" [ 44708.435] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled. [ 44708.435] (WW) Disabling Mouse0 [ 44708.435] (WW) Disabling Keyboard0 [ 44708.435] (II) Loader magic: 0xb77106c0 [ 44708.435] (II) Module ABI versions: [ 44708.435] X.Org ANSI C Emulation: 0.4 [ 44708.435] X.Org Video Driver: 15.0 [ 44708.435] X.Org XInput driver : 20.0 [ 44708.435] X.Org Server Extension : 8.0 [ 44708.436] (II) xfree86: Adding drm device (/dev/dri/card0) [ 44708.436] (II) xfree86: Adding drm device (/dev/dri/card1) [ 44708.437] (--) PCI:*(0:1:5:0) 1002:9616:105b:0e26 rev 0, Mem @ 0xf0000000/134217728, 0xfeae0000/65536, 0xfe900000/1048576, I/O @ 0x0000b000/256 [ 44708.441] Initializing built-in extension Generic Event Extension [ 44708.444] Initializing built-in extension SHAPE [ 44708.448] Initializing built-in extension MIT-SHM [ 44708.452] Initializing built-in extension XInputExtension [ 44708.456] Initializing built-in extension XTEST [ 44708.460] Initializing built-in extension BIG-REQUESTS [ 44708.464] Initializing built-in extension SYNC [ 44708.468] Initializing built-in extension XKEYBOARD [ 44708.471] Initializing built-in extension XC-MISC [ 44708.475] Initializing built-in extension SECURITY [ 44708.479] Initializing built-in extension XINERAMA [ 44708.483] Initializing built-in extension XFIXES [ 44708.487] Initializing built-in extension RENDER [ 44708.491] Initializing built-in extension RANDR [ 44708.494] Initializing built-in extension COMPOSITE [ 44708.498] Initializing built-in extension DAMAGE [ 44708.502] Initializing built-in extension MIT-SCREEN-SAVER [ 44708.506] Initializing built-in extension DOUBLE-BUFFER [ 44708.510] Initializing built-in extension RECORD [ 44708.513] Initializing built-in extension DPMS [ 44708.517] Initializing built-in extension Present [ 44708.521] Initializing built-in extension DRI3 [ 44708.525] Initializing built-in extension X-Resource [ 44708.528] Initializing built-in extension XVideo [ 44708.532] Initializing built-in extension XVideo-MotionCompensation [ 44708.535] Initializing built-in extension SELinux [ 44708.539] Initializing built-in extension XFree86-VidModeExtension [ 44708.542] Initializing built-in extension XFree86-DGA [ 44708.546] Initializing built-in extension XFree86-DRI [ 44708.549] Initializing built-in extension DRI2 [ 44708.549] (II) "glx" will be loaded. This was enabled by default and also specified in the config file. [ 44708.549] (WW) "xmir" is not to be loaded by default. Skipping. [ 44708.549] (II) LoadModule: "glx" [ 44708.549] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 44708.550] (II) Module glx: vendor="X.Org Foundation" [ 44708.550] compiled for 1.15.1, module version = 1.0.0 [ 44708.550] ABI class: X.Org Server Extension, version 8.0 [ 44708.550] (==) AIGLX enabled [ 44708.553] Loading extension GLX [ 44708.553] (II) LoadModule: "udlfb" [ 44708.554] (WW) Warning, couldn't open module udlfb [ 44708.554] (II) UnloadModule: "udlfb" [ 44708.554] (II) Unloading udlfb [ 44708.554] (EE) Failed to load module "udlfb" (module does not exist, 0) [ 44708.554] (II) LoadModule: "modesetting" [ 44708.554] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so [ 44708.554] (II) Module modesetting: vendor="X.Org Foundation" [ 44708.554] compiled for 1.15.0, module version = 0.8.1 [ 44708.554] Module class: X.Org Video Driver [ 44708.554] ABI class: X.Org Video Driver, version 15.0 [ 44708.554] (==) Matched fglrx as autoconfigured driver 0 [ 44708.554] (==) Matched ati as autoconfigured driver 1 [ 44708.554] (==) Matched fglrx as autoconfigured driver 2 [ 44708.554] (==) Matched ati as autoconfigured driver 3 [ 44708.554] (==) Matched modesetting as autoconfigured driver 4 [ 44708.554] (==) Matched fbdev as autoconfigured driver 5 [ 44708.554] (==) Matched vesa as autoconfigured driver 6 [ 44708.554] (==) Assigned the driver to the xf86ConfigLayout [ 44708.554] (II) LoadModule: "fglrx" [ 44708.554] (WW) Warning, couldn't open module fglrx [ 44708.554] (II) UnloadModule: "fglrx" [ 44708.554] (II) Unloading fglrx [ 44708.554] (EE) Failed to load module "fglrx" (module does not exist, 0) [ 44708.554] (II) LoadModule: "ati" [ 44708.554] (II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so [ 44708.554] (II) Module ati: vendor="X.Org Foundation" [ 44708.554] compiled for 1.15.0, module version = 7.3.0 [ 44708.554] Module class: X.Org Video Driver [ 44708.554] ABI class: X.Org Video Driver, version 15.0 [ 44708.554] (II) LoadModule: "radeon" [ 44708.555] (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so [ 44708.555] (II) Module radeon: vendor="X.Org Foundation" [ 44708.555] compiled for 1.15.0, module version = 7.3.0 [ 44708.555] Module class: X.Org Video Driver [ 44708.555] ABI class: X.Org Video Driver, version 15.0 [ 44708.555] (II) LoadModule: "modesetting" [ 44708.555] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so [ 44708.555] (II) Module modesetting: vendor="X.Org Foundation" [ 44708.555] compiled for 1.15.0, module version = 0.8.1 [ 44708.555] Module class: X.Org Video Driver [ 44708.555] ABI class: X.Org Video Driver, version 15.0 [ 44708.555] (II) UnloadModule: "modesetting" [ 44708.555] (II) Unloading modesetting [ 44708.555] (II) Failed to load module "modesetting" (already loaded, 0) [ 44708.555] (II) LoadModule: "fbdev" [ 44708.555] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so [ 44708.555] (II) Module fbdev: vendor="X.Org Foundation" [ 44708.555] compiled for 1.15.0, module version = 0.4.4 [ 44708.555] Module class: X.Org Video Driver [ 44708.555] ABI class: X.Org Video Driver, version 15.0 [ 44708.555] (II) LoadModule: "vesa" [ 44708.555] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so [ 44708.555] (II) Module vesa: vendor="X.Org Foundation" [ 44708.555] compiled for 1.15.0, module version = 2.3.3 [ 44708.555] Module class: X.Org Video Driver [ 44708.555] ABI class: X.Org Video Driver, version 15.0 [ 44708.555] (II) modesetting: Driver for Modesetting Kernel Drivers: kms [ 44708.555] (II) RADEON: Driver for ATI Radeon chipsets: [ 44708.560] (II) FBDEV: driver for framebuffer: fbdev [ 44708.560] (II) VESA: driver for VESA chipsets: vesa [ 44708.560] (--) using VT number 7 [ 44708.578] (II) modesetting(0): using drv /dev/dri/card0 [ 44708.578] (II) modesetting(G0): using drv /dev/dri/card1 [ 44708.578] (WW) Falling back to old probe method for fbdev [ 44708.578] (II) Loading sub module "fbdevhw" [ 44708.578] (II) LoadModule: "fbdevhw" [ 44708.578] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so [ 44708.578] (II) Module fbdevhw: vendor="X.Org Foundation" [ 44708.578] compiled for 1.15.1, module version = 0.0.2 [ 44708.578] ABI class: X.Org Video Driver, version 15.0 [ 44708.578] (WW) Falling back to old probe method for vesa [ 44708.578] (**) modesetting(0): Depth 16, (--) framebuffer bpp 16 [ 44708.578] (==) modesetting(0): RGB weight 565 [ 44708.578] (==) modesetting(0): Default visual is TrueColor [ 44708.578] (II) modesetting(0): ShadowFB: preferred YES, enabled YES [ 44708.608] (II) modesetting(0): Output VGA-0 using monitor section DisplayLinkMonitor [ 44708.610] (II) modesetting(0): Output DVI-0 has no monitor section [ 44708.640] (II) modesetting(0): EDID for output VGA-0 [ 44708.640] (II) modesetting(0): Manufacturer: ACR Model: 74 Serial#: 2483090993 [ 44708.640] (II) modesetting(0): Year: 2009 Week: 40 [ 44708.640] (II) modesetting(0): EDID Version: 1.3 [ 44708.640] (II) modesetting(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V [ 44708.640] (II) modesetting(0): Sync: Separate [ 44708.640] (II) modesetting(0): Max Image Size [cm]: horiz.: 53 vert.: 29 [ 44708.640] (II) modesetting(0): Gamma: 2.20 [ 44708.640] (II) modesetting(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display [ 44708.641] (II) modesetting(0): First detailed timing is preferred mode [ 44708.641] (II) modesetting(0): redX: 0.649 redY: 0.338 greenX: 0.289 greenY: 0.609 [ 44708.641] (II) modesetting(0): blueX: 0.146 blueY: 0.070 whiteX: 0.313 whiteY: 0.329 [ 44708.641] (II) modesetting(0): Supported established timings: [ 44708.641] (II) modesetting(0): 720x400@70Hz [ 44708.641] (II) modesetting(0): 640x480@60Hz [ 44708.641] (II) modesetting(0): 640x480@72Hz [ 44708.641] (II) modesetting(0): 640x480@75Hz [ 44708.641] (II) modesetting(0): 800x600@56Hz [ 44708.641] (II) modesetting(0): 800x600@60Hz [ 44708.641] (II) modesetting(0): 800x600@72Hz [ 44708.641] (II) modesetting(0): 800x600@75Hz [ 44708.641] (II) modesetting(0): 1024x768@60Hz [ 44708.641] (II) modesetting(0): 1024x768@70Hz [ 44708.641] (II) modesetting(0): 1024x768@75Hz [ 44708.641] (II) modesetting(0): 1280x1024@75Hz [ 44708.641] (II) modesetting(0): Manufacturer's mask: 0 [ 44708.641] (II) modesetting(0): Supported standard timings: [ 44708.641] (II) modesetting(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897 [ 44708.641] (II) modesetting(0): #1: hsize: 1152 vsize 864 refresh: 75 vid: 20337 [ 44708.641] (II) modesetting(0): #2: hsize: 1440 vsize 900 refresh: 60 vid: 149 [ 44708.641] (II) modesetting(0): #3: hsize: 1440 vsize 900 refresh: 75 vid: 3989 [ 44708.641] (II) modesetting(0): #4: hsize: 1600 vsize 1200 refresh: 60 vid: 16553 [ 44708.641] (II) modesetting(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179 [ 44708.641] (II) modesetting(0): Supported detailed timing: [ 44708.641] (II) modesetting(0): clock: 138.5 MHz Image Size: 531 x 298 mm [ 44708.641] (II) modesetting(0): h_active: 1920 h_sync: 1968 h_sync_end 2000 h_blank_end 2080 h_border: 0 [ 44708.641] (II) modesetting(0): v_active: 1080 v_sync: 1083 v_sync_end 1088 v_blanking: 1111 v_border: 0 [ 44708.641] (II) modesetting(0): Monitor name: H243H [ 44708.641] (II) modesetting(0): Ranges: V min: 56 V max: 76 Hz, H min: 31 H max: 83 kHz, PixClock max 185 MHz [ 44708.641] (II) modesetting(0): Serial No: LEW0C0044002 [ 44708.641] (II) modesetting(0): EDID (in hex): [ 44708.641] (II) modesetting(0): 00ffffffffffff000472740031f60094 [ 44708.641] (II) modesetting(0): 2813010368351d78ea6085a6564a9c25 [ 44708.641] (II) modesetting(0): 125054afcf008180714f9500950fa940 [ 44708.641] (II) modesetting(0): b300010101011a3680a070381f403020 [ 44708.641] (II) modesetting(0): 3500132a2100001a000000fc00483234 [ 44708.642] (II) modesetting(0): 33480a20202020202020000000fd0038 [ 44708.642] (II) modesetting(0): 4c1f5312000a202020202020000000ff [ 44708.642] (II) modesetting(0): 004c45573043303034343030320a003c [ 44708.642] (II) modesetting(0): Printing probed modes for output VGA-0 [ 44708.642] (II) modesetting(0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz UeP) [ 44708.642] (II) modesetting(0): Modeline "1920x1080"x59.9 138.50 1920 1968 2000 2080 1080 1083 1088 1111 +hsync -vsync (66.6 kHz eP) [ 44708.642] (II) modesetting(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1440x900"x75.0 136.75 1440 1536 1688 1936 900 903 909 942 -hsync +vsync (70.6 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1440x900"x59.9 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e) [ 44708.642] (II) modesetting(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) [ 44708.642] (II) modesetting(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e) [ 44708.642] (II) modesetting(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e) [ 44708.642] (II) modesetting(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) [ 44708.642] (II) modesetting(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) [ 44708.642] (II) modesetting(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e) [ 44708.642] (II) modesetting(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e) [ 44708.642] (II) modesetting(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 44708.642] (II) modesetting(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e) [ 44708.645] (II) modesetting(0): EDID for output DVI-0 [ 44708.645] (II) modesetting(0): Output VGA-0 connected [ 44708.645] (II) modesetting(0): Output DVI-0 disconnected [ 44708.645] (II) modesetting(0): Using user preference for initial modes [ 44708.645] (II) modesetting(0): Output VGA-0 using initial mode 1280x1024 [ 44708.645] (II) modesetting(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 44708.645] (==) modesetting(0): DPI set to (96, 96) [ 44708.645] (II) Loading sub module "fb" [ 44708.645] (II) LoadModule: "fb" [ 44708.645] (II) Loading /usr/lib/xorg/modules/libfb.so [ 44708.645] (II) Module fb: vendor="X.Org Foundation" [ 44708.645] compiled for 1.15.1, module version = 1.0.0 [ 44708.645] ABI class: X.Org ANSI C Emulation, version 0.4 [ 44708.645] (II) Loading sub module "shadow" [ 44708.645] (II) LoadModule: "shadow" [ 44708.646] (II) Loading /usr/lib/xorg/modules/libshadow.so [ 44708.646] (II) Module shadow: vendor="X.Org Foundation" [ 44708.646] compiled for 1.15.1, module version = 1.1.0 [ 44708.646] ABI class: X.Org ANSI C Emulation, version 0.4 [ 44708.646] (**) modesetting(G0): Depth 16, (--) framebuffer bpp 16 [ 44708.646] (==) modesetting(G0): RGB weight 565 [ 44708.646] (==) modesetting(G0): Default visual is TrueColor [ 44708.646] (II) modesetting(G0): ShadowFB: preferred NO, enabled NO [ 44708.727] (II) modesetting(G0): Output DVI-1-0 using monitor section DisplayLinkMonitor [ 44708.808] (II) modesetting(G0): EDID for output DVI-1-0 [ 44708.808] (II) modesetting(G0): Manufacturer: WDE Model: 1702 Serial#: 0 [ 44708.808] (II) modesetting(G0): Year: 2005 Week: 14 [ 44708.808] (II) modesetting(G0): EDID Version: 1.3 [ 44708.808] (II) modesetting(G0): Analog Display Input, Input Voltage Level: 0.700/0.700 V [ 44708.808] (II) modesetting(G0): Sync: Separate [ 44708.808] (II) modesetting(G0): Max Image Size [cm]: horiz.: 34 vert.: 27 [ 44708.808] (II) modesetting(G0): Gamma: 2.20 [ 44708.808] (II) modesetting(G0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display [ 44708.808] (II) modesetting(G0): Default color space is primary color space [ 44708.808] (II) modesetting(G0): First detailed timing is preferred mode [ 44708.808] (II) modesetting(G0): GTF timings supported [ 44708.808] (II) modesetting(G0): redX: 0.643 redY: 0.352 greenX: 0.283 greenY: 0.608 [ 44708.808] (II) modesetting(G0): blueX: 0.147 blueY: 0.102 whiteX: 0.313 whiteY: 0.329 [ 44708.808] (II) modesetting(G0): Supported established timings: [ 44708.808] (II) modesetting(G0): 720x400@70Hz [ 44708.808] (II) modesetting(G0): 640x480@60Hz [ 44708.808] (II) modesetting(G0): 640x480@67Hz [ 44708.808] (II) modesetting(G0): 640x480@72Hz [ 44708.808] (II) modesetting(G0): 640x480@75Hz [ 44708.808] (II) modesetting(G0): 800x600@56Hz [ 44708.808] (II) modesetting(G0): 800x600@60Hz [ 44708.808] (II) modesetting(G0): 800x600@72Hz [ 44708.808] (II) modesetting(G0): 800x600@75Hz [ 44708.808] (II) modesetting(G0): 832x624@75Hz [ 44708.808] (II) modesetting(G0): 1024x768@60Hz [ 44708.808] (II) modesetting(G0): 1024x768@70Hz [ 44708.808] (II) modesetting(G0): 1024x768@75Hz [ 44708.809] (II) modesetting(G0): 1280x1024@75Hz [ 44708.809] (II) modesetting(G0): Manufacturer's mask: 0 [ 44708.809] (II) modesetting(G0): Supported standard timings: [ 44708.809] (II) modesetting(G0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897 [ 44708.809] (II) modesetting(G0): #1: hsize: 1152 vsize 864 refresh: 75 vid: 20337 [ 44708.809] (II) modesetting(G0): Supported detailed timing: [ 44708.809] (II) modesetting(G0): clock: 108.0 MHz Image Size: 338 x 270 mm [ 44708.809] (II) modesetting(G0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0 [ 44708.809] (II) modesetting(G0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0 [ 44708.809] (II) modesetting(G0): Ranges: V min: 50 V max: 75 Hz, H min: 30 H max: 82 kHz, PixClock max 145 MHz [ 44708.809] (II) modesetting(G0): Monitor name: WDE LCM-17v2 [ 44708.809] (II) modesetting(G0): Serial No: 0 [ 44708.809] (II) modesetting(G0): EDID (in hex): [ 44708.809] (II) modesetting(G0): 00ffffffffffff005c85021700000000 [ 44708.809] (II) modesetting(G0): 0e0f010368221b78ef8bc5a45a489b25 [ 44708.809] (II) modesetting(G0): 1a5054bfef008180714f010101010101 [ 44708.809] (II) modesetting(G0): 010101010101302a009851002a403070 [ 44708.809] (II) modesetting(G0): 1300520e1100001e000000fd00324b1e [ 44708.809] (II) modesetting(G0): 520e000a202020202020000000fc0057 [ 44708.809] (II) modesetting(G0): 4445204c434d2d313776320a000000ff [ 44708.809] (II) modesetting(G0): 00300a202020202020202020202000e7 [ 44708.809] (II) modesetting(G0): Printing probed modes for output DVI-1-0 [ 44708.809] (II) modesetting(G0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz UeP) [ 44708.809] (II) modesetting(G0): Modeline "1280x1024"x75.0 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync (80.0 kHz e) [ 44708.809] (II) modesetting(G0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e) [ 44708.809] (II) modesetting(G0): Modeline "1280x800"x74.9 106.50 1280 1360 1488 1696 800 803 809 838 -hsync +vsync (62.8 kHz e) [ 44708.809] (II) modesetting(G0): Modeline "1280x800"x59.8 83.50 1280 1352 1480 1680 800 803 809 831 +hsync -vsync (49.7 kHz e) [ 44708.809] (II) modesetting(G0): Modeline "1152x864"x75.0 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync (67.5 kHz e) [ 44708.809] (II) modesetting(G0): Modeline "1280x768"x74.9 102.25 1280 1360 1488 1696 768 771 778 805 +hsync -vsync (60.3 kHz e) [ 44708.809] (II) modesetting(G0): Modeline "1280x768"x59.9 79.50 1280 1344 1472 1664 768 771 778 798 -hsync +vsync (47.8 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "1024x576"x60.0 46.97 1024 1064 1168 1312 576 577 580 597 -hsync +vsync (35.8 kHz) [ 44708.810] (II) modesetting(G0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 44708.810] (II) modesetting(G0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz e) [ 44708.810] (II) modesetting(G0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 44708.810] (==) modesetting(G0): DPI set to (96, 96) [ 44708.810] (II) Loading sub module "fb" [ 44708.810] (II) LoadModule: "fb" [ 44708.810] (II) Loading /usr/lib/xorg/modules/libfb.so [ 44708.810] (II) Module fb: vendor="X.Org Foundation" [ 44708.810] compiled for 1.15.1, module version = 1.0.0 [ 44708.811] ABI class: X.Org ANSI C Emulation, version 0.4 [ 44708.811] (II) UnloadModule: "radeon" [ 44708.811] (II) Unloading radeon [ 44708.811] (II) UnloadModule: "fbdev" [ 44708.811] (II) Unloading fbdev [ 44708.811] (II) UnloadSubModule: "fbdevhw" [ 44708.811] (II) Unloading fbdevhw [ 44708.811] (II) UnloadModule: "vesa" [ 44708.811] (II) Unloading vesa [ 44708.811] (==) modesetting(G0): Backing store enabled [ 44708.811] (==) modesetting(G0): Silken mouse enabled [ 44708.812] (II) modesetting(G0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 44708.812] (==) modesetting(G0): DPMS enabled [ 44708.812] (WW) modesetting(G0): Option "fbdev" is not used [ 44708.812] (==) modesetting(0): Backing store enabled [ 44708.812] (==) modesetting(0): Silken mouse enabled [ 44708.812] (II) modesetting(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 44708.812] (==) modesetting(0): DPMS enabled [ 44708.812] (WW) modesetting(0): Option "fbdev" is not used [ 44708.856] (--) RandR disabled [ 44708.867] (II) SELinux: Disabled on system [ 44708.868] (II) AIGLX: Screen 0 is not DRI2 capable [ 44708.868] (EE) AIGLX: reverting to software rendering [ 44708.878] (II) AIGLX: Loaded and initialized swrast [ 44708.878] (II) GLX: Initialized DRISWRAST GL provider for screen 0 [ 44708.879] (II) modesetting(G0): Damage tracking initialized [ 44708.879] (II) modesetting(0): Damage tracking initialized [ 44708.879] (II) modesetting(0): Setting screen physical size to 338 x 270 [ 44708.900] (II) XKB: generating xkmfile /tmp/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm [ 44708.918] (II) config/udev: Adding input device Power Button (/dev/input/event1) [ 44708.918] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 44708.918] (II) LoadModule: "evdev" [ 44708.918] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so [ 44708.918] (II) Module evdev: vendor="X.Org Foundation" [ 44708.918] compiled for 1.15.0, module version = 2.8.2 [ 44708.918] Module class: X.Org XInput Driver [ 44708.918] ABI class: X.Org XInput driver, version 20.0 [ 44708.918] (II) Using input driver 'evdev' for 'Power Button' [ 44708.918] (**) Power Button: always reports core events [ 44708.918] (**) evdev: Power Button: Device: "/dev/input/event1" [ 44708.918] (--) evdev: Power Button: Vendor 0 Product 0x1 [ 44708.918] (--) evdev: Power Button: Found keys [ 44708.918] (II) evdev: Power Button: Configuring as keyboard [ 44708.918] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1" [ 44708.918] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6) [ 44708.918] (**) Option "xkb_rules" "evdev" [ 44708.918] (**) Option "xkb_model" "pc105" [ 44708.918] (**) Option "xkb_layout" "us" [ 44708.919] (II) config/udev: Adding input device Power Button (/dev/input/event0) [ 44708.919] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 44708.919] (II) Using input driver 'evdev' for 'Power Button' [ 44708.919] (**) Power Button: always reports core events [ 44708.919] (**) evdev: Power Button: Device: "/dev/input/event0" [ 44708.919] (--) evdev: Power Button: Vendor 0 Product 0x1 [ 44708.919] (--) evdev: Power Button: Found keys [ 44708.919] (II) evdev: Power Button: Configuring as keyboard [ 44708.919] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0" Is there anything I can do to fix this problem.

  Read the article

• ORACLE Forms Upgrade Workshops

  - by Thomas Leopold

     09. Februar 2011 Workshop: Forms Upgrade von 10g (iAS) nach 11g (WLS) Oracle Deutschland lädt Sie zu einem Workshop zum Thema Forms Upgrade von 10g (iAS) nach 11g (WLS) ein. Der Workshop ist für Entwickler und Administratoren gedacht, die sich einen Überblick über die Änderungen verschaffen möchten, die sich aus der Migration von 10g auf 11g ergeben. Der Wokshop gibt einen Überblick über die architekturellen Unterschiede zwischen dem Internet Application Server und dem WebLogic Server. Er erläutert die für den Betrieb von Forms-Anwendungen relevanten Unterschiede und Gemeinsamkeiten beider Ansätze. Im HandsOn-Teil migrieren die Teilnehmer selbst einige (exemplarische) Forms-Anwendungen von 10g nach 11g und konfigurieren den WLS zum Betrieb der Forms-Module.   Agenda Beginn: 10:00 Uhr Architektur des WebLogicServers, Unterschiede 10g (iAS) und 11g (WLS) Forms unter WebLogicServer 11g Forms 11g - New Features Administration von Formsanwendungen unter 11g HandsOn: Migration von Forms-Beispielanwendungen Ende: 16:00 Uhr Termine 30. März 2011 - Potsdam | Registrieren 31. März 2011 - Hamburg | Registrieren Technische Voraussetzungen Zur Nutzung des Migrationsassistenten unter 11g müssen die Installationen 10g (iAS) und 11g (WLS) auf einem Server parallel betrieben werden. Dazu ist ein Rechner mit mindestens 4 GB RAM erforderlich; die entsprechenden Installationen werden als virtuelle Maschine zur Verfügung gestellt. Sofern Sie über keinen ausreichend dimensionierten Laptop verfügen, können wir Ihnen für den Workshop ein entsprechendes Gerät ausleihen. Bitte geben Sie dies bei der Anmeldung an, da wir nur über eine begrenzte Anzahl von Leihlaptops verfügen. Wenn Sie den Workshop auf Ihrem Laptop durchführen möchten, beachten Sie bitte die folgenden Systemvoraussetzungen 4 GB RAM Oracle VirtualBox (4.0.2) (incl. GuestAdditions) Anmeldung Zur Anmeldung nutzen Sie bitte die o.a. Links. Der Workshop ist für die Teilnehmer kostenlos. Bei Fragen oder Anmerkungen wenden Sie sich bitte an Christian Kühne (0511-95787-143)ORACLE Deutschland B.V. & Co. KGThurnithistrasse 2-630519 Hannover oder Wolfgang Kriebel (0331 2007 295) ORACLE Deutschland B.V. & Co. KGSchiffbauergasse 1414467 Potsdam ORACLE Deutschland B.V. & Co. KG, Hauptverwaltung: Riesstraße 25, D-80992 München Registergericht: Amtsgericht München, HRA 95603 Komplementärin ORACLE Deutschland Verwaltung B.V. Rijnzathe 6, 3454PV De Meern, Niederlande Handelsregister der Handelskammer Midden-Niederlande, Nr. 30143697 Geschäftsführer: Jürgen Kunz, Marcel van de Molen, Alexander van der Ven  

  Read the article

• Oracle bleibt auch 2011 Spitzenreiter im Bereich Datenbanken

  - by Anne Manke

  Mit der Veröffentlichung der aktuellen Ausgabe "Market Share: All Software Markets, Worldwide 2011" bestätigt das weltweit führende Marktanalyseunternehmen Gartner Oracle's Marktführerschaft im Bereich der Relationellen Datenbank Management Systeme (RDBMS). Oracle konnte innerhalb des letzten Jahres seinen Abstand zu seinen Marktbegleitern im Bereich der RDBMS mit einem stabilen Wachstum von 18% sogar ausbauen: der Marktanteil stieg im Jahr 2010 von 48,2% auf 48,8% im Jahr 2011. Damit ist der Abstand zu Oracle's stärkstem Verfolger IBM auf 28,6%.   Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:12.0pt; mso-para-margin-left:0cm; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} table.MsoTableLightListAccent2 {mso-style-name:"Light List - Accent 2"; mso-tstyle-rowband-size:1; mso-tstyle-colband-size:1; mso-style-priority:61; mso-style-unhide:no; border:solid #C0504D 1.0pt; mso-border-themecolor:accent2; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} table.MsoTableLightListAccent2FirstRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:first-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-shading:#C0504D; mso-tstyle-shading-themecolor:accent2; mso-para-margin-top:0cm; mso-para-margin-bottom:0cm; mso-para-margin-bottom:.0001pt; line-height:normal; color:white; mso-themecolor:background1; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2LastRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:last-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:2.25pt double #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2; mso-para-margin-top:0cm; mso-para-margin-bottom:0cm; mso-para-margin-bottom:.0001pt; line-height:normal; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2FirstCol {mso-style-name:"Light List - Accent 2"; mso-table-condition:first-column; mso-style-priority:61; mso-style-unhide:no; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2LastCol {mso-style-name:"Light List - Accent 2"; mso-table-condition:last-column; mso-style-priority:61; mso-style-unhide:no; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2OddColumn {mso-style-name:"Light List - Accent 2"; mso-table-condition:odd-column; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:1.0pt solid #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2;} table.MsoTableLightListAccent2OddRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:odd-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:1.0pt solid #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2;} Revenue 2010 ($USM) Revenue 2011 ($USM) Growth 2010 Growth 2011 Share 2010 Share 2011 Oracle 9,990.5 11,787.0 10.9% 18.0% 48.2% 48.8% IBM 4,300.4 4,870.4 5.4% 13.3% 20.7% 20.2% Microsoft 3,641.2 4,098.9 10.1% 12.6% 17.6% 17.0% SAP/Sybase 744.4 1,101.1 12.8% 47.9% 3.6% 4.6% Teradata 754.7 882.3 16.9% 16.9% 3.6% 3.7% Source: Gartner’s “Market Share: All Software Markets, Worldwide 2011,” March 29, 2012, By Colleen Graham, Joanne Correia, David Coyle, Fabrizio Biscotti, Matthew Cheung, Ruggero Contu, Yanna Dharmasthira, Tom Eid, Chad Eschinger, Bianca Granetto, Hai Hong Swinehart, Sharon Mertz, Chris Pang, Asheesh Raina, Dan Sommer, Bhavish Sood, Marianne D'Aquila, Laurie Wurster and Jie Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:12.0pt; mso-para-margin-left:0cm; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} table.MsoTableLightListAccent2 {mso-style-name:"Light List - Accent 2"; mso-tstyle-rowband-size:1; mso-tstyle-colband-size:1; mso-style-priority:61; mso-style-unhide:no; border:solid #C0504D 1.0pt; mso-border-themecolor:accent2; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} table.MsoTableLightListAccent2FirstRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:first-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-shading:#C0504D; mso-tstyle-shading-themecolor:accent2; mso-para-margin-top:0cm; mso-para-margin-bottom:0cm; mso-para-margin-bottom:.0001pt; line-height:normal; color:white; mso-themecolor:background1; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2LastRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:last-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:2.25pt double #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2; mso-para-margin-top:0cm; mso-para-margin-bottom:0cm; mso-para-margin-bottom:.0001pt; line-height:normal; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2FirstCol {mso-style-name:"Light List - Accent 2"; mso-table-condition:first-column; mso-style-priority:61; mso-style-unhide:no; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2LastCol {mso-style-name:"Light List - Accent 2"; mso-table-condition:last-column; mso-style-priority:61; mso-style-unhide:no; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2OddColumn {mso-style-name:"Light List - Accent 2"; mso-table-condition:odd-column; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:1.0pt solid #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2;} table.MsoTableLightListAccent2OddRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:odd-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:1.0pt solid #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2;} Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:12.0pt; mso-para-margin-left:0cm; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} table.MsoTableLightListAccent2 {mso-style-name:"Light List - Accent 2"; mso-tstyle-rowband-size:1; mso-tstyle-colband-size:1; mso-style-priority:61; mso-style-unhide:no; border:solid #C0504D 1.0pt; mso-border-themecolor:accent2; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} table.MsoTableLightListAccent2FirstRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:first-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-shading:#C0504D; mso-tstyle-shading-themecolor:accent2; mso-para-margin-top:0cm; mso-para-margin-bottom:0cm; mso-para-margin-bottom:.0001pt; line-height:normal; color:white; mso-themecolor:background1; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2LastRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:last-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:2.25pt double #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2; mso-para-margin-top:0cm; mso-para-margin-bottom:0cm; mso-para-margin-bottom:.0001pt; line-height:normal; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2FirstCol {mso-style-name:"Light List - Accent 2"; mso-table-condition:first-column; mso-style-priority:61; mso-style-unhide:no; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2LastCol {mso-style-name:"Light List - Accent 2"; mso-table-condition:last-column; mso-style-priority:61; mso-style-unhide:no; mso-ansi-font-weight:bold; mso-bidi-font-weight:bold;} table.MsoTableLightListAccent2OddColumn {mso-style-name:"Light List - Accent 2"; mso-table-condition:odd-column; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:1.0pt solid #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2;} table.MsoTableLightListAccent2OddRow {mso-style-name:"Light List - Accent 2"; mso-table-condition:odd-row; mso-style-priority:61; mso-style-unhide:no; mso-tstyle-border-top:1.0pt solid #C0504D; mso-tstyle-border-top-themecolor:accent2; mso-tstyle-border-left:1.0pt solid #C0504D; mso-tstyle-border-left-themecolor:accent2; mso-tstyle-border-bottom:1.0pt solid #C0504D; mso-tstyle-border-bottom-themecolor:accent2; mso-tstyle-border-right:1.0pt solid #C0504D; mso-tstyle-border-right-themecolor:accent2;}

  Read the article

• Megjelent az Oracle Enterprise Manager 11g

  - by Lajos Sárecz

  Megjelent és letöltheto az Oracle Enterprise Manager 11gR1. Remélem az olvasók közül többen látták már a bejelentés videóját. Aki lemaradt volna róla bepótolhatja itt. Az új verzió számos újdonságot tartalmaz, melyek röviden összefoglalva az alábbiak: Eloször is az új verzió célja az alkalmazások üzemeltetése üzleti szemszögbol (Business Driven Application Management). A hagyományos komponens alapú rendszer menedzsment megközelítése egyszeruen nem állja meg a helyét az mai IT világában. Ezzel szemben a Business Driven Application Management segíti az üzemeltetoket, hogy az üzletet a leheto leghatékonyabban szolgálják ki, aminek eredményeképp az üzleti eredmények a legoptimálisabban alakulhatnak. A Business Driven Application Management elérése érdekében a 11gR1 a 10g-ben már elérheto végfelhasználói élmény monitorozásra épít. Ezzel a képességgel az IT sokkal jobban megérti, hogy a felhasználók hogyan használják az alkalmazásokat és eközben mit tapasztalnak. Ezt kiegészítve az új verzió fejlettebb üzleti tranzakció menedzsment képességekkel rendelkezik, ezáltal könnyebbé és gyorsabbá teszi a felhasználók számára problémát jelento tranzakciók javítását. Másodsorban az új verzió az alkalmazástól a diszk rétegig (Integrated Application-to-Disk Management) támogatja az üzemeltetést. Mivel minden egyes réteg képes befolyásolni a felhasználói élményt, ezért amint a felhasználókat érinto probléma detektálásra kerül, szükséges az érintett réteg részletes diagnosztikája, elemzése. Az Oracle Enterprise Manager 11gR1 natív támogatást ad az Oracle Database 11gR2, Exadata V2 és Fusion Middleware 11g termékekre. Az összetett alkalmazások menedzsmentjét támogató JVM Diagnosztika és Composite Application Monitoring and Modeler immár szerves részét képezik az új verziónak. Sot, az Enterprise Manager Grid Control és az Enterprise Manager Ops Center elso integrációs lépcsoje is elkészült, így a hardver szintu események is központilag monitorozhatók a Grid Control felületérol. Végül pedig az új verzió integrált rendszer menedzsement és támogatás (Integrated Systems Management and Support) képességgel rendelkezik. Ez azt jelenti, hogy az Oracle Enterprise Manager 11g integrálja a probléma diagnosztizálás és megoldás munkafolyamatát azáltal, hogy közvetlenül a Grid Control-ból lehetségessé válik a My Oracle Support szolgáltatásainak igénybevétele, mint például a szükséges patch-ek letöltése, service request nyitása, stb. Az Oracle support személyzete pedig az Enterprise Manager konfiguráció kezelési képességei révén azonnal információt gyujthetnek a környezetrol, hogy felgyorsuljon a probléma megoldás ideje. Ez a szoros integráció az Oracle Enterprise Manager és a My Oracle Support között segítheti ügyfeleinket a leghatékonyabb Oracle üzemeltetés elérésében. A következo hetekben igyekszem további részletekkel szolgálni, amint én is megismerem az új verzió képességeit. Az új verzió jelenleg 32 és 64 bites Linuxra érheto el. További portolások a következo hetekben várhatók.

  Read the article

• Silverlight Cream for May 20, 2010 -- #866

  - by Dave Campbell

  In this Issue: Mike Snow, Victor Gaudioso, Ola Karlsson, Josh Twist(-2-), Yavor Georgiev, Jeff Wilcox, and Jesse Liberty. Shoutouts: Frank LaVigne has an interesting observation on his site: The Big Take-Away from MIX10 Rishi has updated all his work including a release of nRoute to the latest bits: nRoute Samples Revisited Looks like I posted one of Erik Mork's links two days in a row :) ... that's because I meant to post this one: Silverlight Week – How to Choose a Mobile Platform Just in case you missed it (and for me to find it easy), Scott Guthrie has an excellent post up on Silverlight 4 Tools for VS 2010 and WCF RIA Services Released From SilverlightCream.com: Silverlight Tip of the Day #23 – Working with Strokes and Shapes Mike Snow's Silverlight Tip of the Day number 23 is up and about Strokes and Shapes -- as in dotted and dashed lines. New Silverlight Video Tutorial: How to Fire a Visual State based upon the value of a Boolean Variable Victor Gaudioso's latest video tutorial is up and is on selecting and firing a video state based on a boolean... project included. Simultaneously calling multiple methods on a WCF service from silverlight Ola Karlsson details a problem he had where he was calling multiple WCF services to pull all his data and had problems... turns out it was a blocking call and he found the solution in the forums and details it all out for us... actually, a search at SilverlightCream.com would have found one of the better posts listed once you knew the problem :) Securing Your Silverlight Applications Josh Twist has an article in MSDN on Silverlight Security. He talks about Windows, forms, and .NET authorization then WCF, WCF Data, cross domain and XAP files. He also has some good external links. Template/View selection with MEF in Silverlight Josh Twist points out that this next article is just a simple demonstration, but he's discussing, and provides code for, a MEF-driven ViewModel navigation scheme with animation on the navigation. Workaround for accessing some ASMX services from Silverlight 4 Are you having problems hitting you asmx web service with Silverlight 4? Yeah... others are too! Yavor Georgiev at the Silverlight Web Services Team blog has a post up about it... why it's a sometimes problem and a workaround for it. Using Silverlight 4 features to create a Zune-like context menu Jeff Wilcox used Silverlight 4 and the Toolkit to create some samples of menus, then demonstrates a duplication of the Zune menu. You Already Are A Windows Phone 7 Programmer Jesse Liberty is demonstrating the fact that Silverlight developers are WP7 developers by creating a Silverlight and a WP7 app side by side using the same code... this is a closer look at the Silverlight TV presentation he did. Stay in the 'Light! Twitter SilverlightNews | Twitter WynApse | WynApse.com | Tagged Posts | SilverlightCream Join me @ SilverlightCream | Phoenix Silverlight User Group Technorati Tags: Silverlight    Silverlight 3    Silverlight 4    Windows Phone MIX10

  Read the article

• Does using GCC specific builtins qualify as incorporation within a project?

  - by DavidJFelix

  I understand that linking to a program licensed under the GPL requires that you release the source of your program under the GPL as well, while the LGPL does not require this. The terminology of the (L)GPL is very clear about this. #include "gpl_program.h" means you'd have to license GPL, because you're linking to GPL licensed code. And #include "lgpl_program.h" means you're free to license however you want, so that it doesn't explicitly prohibit linking to LGPL source. Now, my question about what isn't clear is: [begin question] GCC is GPL licensed, compiling with GCC, does not constitute "integration" into your program, as the GPL puts it; does using builtin functions (which are specific to GCC) constitute "incorporation" even though you haven't explicitly linked to this GPL licensed code? My intuition tells me that this isn't the intention, but legality isn't always intuitive. I'm not actually worried, but I'm curious if this could be considered the case. [end question] [begin aside] The reason for my equivocation is that GCC builtins like __builtin_clzl() or __builtin_expect() are an API technically and could be implemented in another way. For example, many builtins were replicated by LLVM and the argument could be made that it's not implementation specific to GCC. However, many builtins have no parallel and when compiled will link GPL licensed code in GCC and will not compile on other compilers. If you make the argument here that the API could be replicated by another compiler, couldn't you make that identical claim about any program you link to, so long as you don't distribute that source? I understand that I'm being a legal snake about this, but it strikes me as odd that the GPL isn't more specific. I don't see this as a reasonable ploy for proprietary software creators to bypass the GPL, as they'd have to bundle the GPL software to make it work, removing their plausible deniability. However, isn't it possible that if builtins don't constitute linking, then open source proponents who oppose the GPL could simply write a BSD/MIT/Apache/Apple licensed product that links to a GPL'd program and claim that they intend to write a non-GPL interface that is identical to the GPL one, preserving their BSD license until it's actually compiled? [end aside] Sorry for the aside, I didn't think many people would follow why I care about this if I'm not facing any legal trouble or implications. Don't worry too much about the hypotheticals there, I'm just extrapolating what either answer to my actual question could imply.

  Read the article

• What source code organization approach helps improve modularity and API/Implementation separation?

  - by Berin Loritsch

  Few languages are as restrictive as Java with file naming standards and project structure. In that language, the file name must match the public class declared in the file, and the file must live in a directory structure matching the class package. I have mixed feelings about that approach. While I never have to guess where a file lives, there's still a lot of empty directories and artificial constraints. There's several languages that define everything about a class in one file, at least by convention. C#, Python (I think), Ruby, Erlang, etc. The commonality in most these languages is that they are object oriented, although that statement can probably be rebuffed (there is one non-OO language in the list already). Finally, there's quite a few languages mostly in the C family that have a separate header and implementation file. For C I think this makes sense, because it is one of the few ways to separate the API interface from implementations. With C it seems that feature is used to promote modularity. Yet, with C++ the way header and implementation files are split seems rather forced. You don't get the same clean API separation that you do with C, and you are forced to include some private details in the header you would rather keep only in the implementation. There's quite a few languages that have a concept that overlaps with interfaces like Java, C#, Go, etc. Some languages use what feels like a hack to provide the same concept like C# using pure virtual abstract classes. Still others don't really have an interface concept and rely on "duck" typing--for example Ruby. Ruby has modules, but those are more along the lines of mixing in behaviors to a class than they are for defining how to interact with a class. In OO terms, interfaces are a powerful way to provide separation between an API client and an API implementation. So to hurry up and ask the question, from a personal experience point of view: Does separation of header and implementation help you write more modular code, or does it get in the way? (it helps to specify the language you are referring to) Does the strict file name to class name scheme of Java help maintainability, or is it unnecessary structure for structure's sake? What would you propose to promote good API/Implementation separation and project maintenance, how would you prefer to do it?

  Read the article

• Credentials Not Passed From SharePoint WebPart to WCF Service

  - by Jacob L. Adams

  I have spent several hours trying to resolve this problem, so I wanted to share my findings in case someone else might have the same problem. I had a web part which was calling out to a WCF service on another server to get some data. The code I had was essentially using System.ServiceModel; using System.ServiceModel.Channels; ... var binding = new CustomBinding( new HttpTransportBindingElement { AuthenticationScheme = System.Net.AuthenticationSchemes.Negotiate } ); var endpoint = new EndpointAddress(new Uri("http://someotherserver/someotherservice.svc")); var someOtherService = new SomeOtherServiceClient(binding, endpoint); string result = someOtherService.SomeServiceMethod(); This code would run fine on my local instance of SharePoint 2010 (Windows 7 64-bit). However, when I would deploy it to the testing environment, I would get a yellow screen of death  with the following message: The HTTP request is unauthorized with client authentication scheme 'Negotiate'. The authentication header received from the server was 'Negotiate,NTLM'. I then went through the usual checklist of Windows Authentication problems: Check WCF bindings to make sure authentication is set correctly Check IIS to make sure Windows Authentication is enabled and anonymous authentication was disabled. Check to make sure the SharePoint server trusted the server hosting the WCF service Verify that the account that the IIS application pool is running under has access to the other server I then spend lot of time digging into really obscure IIS, machine.config, and trust settings (as well of lots of time on Google and StackOverflow). Eventually I stumbled upon a blog post by Todd Bleeker describing how to run code under the application pool identity. Wait, what? The code is not already running under application pool identity? Another quick Google search led me to an MSDN page that imply that SharePoint indeed does not run under the app pool credentials by default. Instead SPSecurity.RunWithElevatedPrivileges is needed to run code under the app pool identity. Therefore, changing my code to the following worked seamlessly using System.ServiceModel; using System.ServiceModel.Channels; using Microsoft.SharePoint; ... var binding = new CustomBinding( new HttpTransportBindingElement { AuthenticationScheme = System.Net.AuthenticationSchemes.Negotiate } ); var endpoint = new EndpointAddress(new Uri("http://someotherserver/someotherservice.svc")); var someOtherService = new SomeOtherServiceClient(binding, endpoint); string result; SPSecurity.RunWithElevatedPrivileges(()=> { result = someOtherService.SomeServiceMethod(); });

  Read the article

• Finding work as a college student

  - by lightburst

  I'm a 3rd year CS student. I'm currently really, really, bored and tired of cheap school programming(I go to a fairly respectable(albeit not top) university in my country, but, really, it's not MIT) so I've been thinking about getting a part-time dev job for a long while now. I'm not some hotshot programmer or anything, but "Add/Delete XYZ class objects to list" or "Do this web feature/pattern in PHP" does get old after a few semesters. I also only learned(heard?) of programming when I entered college, so the duration of me being in contact with any code is short. I can't really apply as an intern as I have not accumulated the necessary credits yet to do that so I was thinking of selling myself as a part-time dev. I still need to go to school, and don't want to subject myself to living two lives. Plus, I think I'd have better chances considering my lack of things to write on the resume. The only language I know at heart is C (I've written several pointer-oriented stuff on my freshman year, which is apparently pretty leet(for some reason), or so Joel says. That sort of boosted my morale a bit) but I've worked with several other languages only for the sake of course work such as C#/Java/PHP/ASM. My only user-worthy project was a recursive quicksort simulator I wrote for class using GTK+ that used a textbox to output the progress. I also have not taken the compiler theory class yet, or my thesis. All that being said, I wonder if any legitimate software company(big or small) would hire somebody like me considering all that. If there are companies that do accept anybody like me, would I be doing programming or maybe just be a tester or something? Would anybody hire me as a dev at all? I know I don't have much(not even a degree) but what I lack in experience, I compensate with interest? I am less interested in websites and 'management' software(no offense or anything. also, most of the places here ONLY have those), and more into 'process driven'(I'm not sure how to call it) and system software. I have my eyes on a startup that sells basically an extension of Google Drive, but I feel like I'm too 'risky' for them. Oh, I'm also 19 if that means anything. We're not K-12 so kids go to college earlier than in the US.

  Read the article

• Windows Phone 7 Development Updates &ndash; March 8th 2011

  - by Nikita Polyakov

  Here are the latest update from the Windows Phone 7 Developer Worlds that went live this month. Here are some of the latest numbers: Windows Phone Marketplace currently offers more than 9,000 quality apps and games and enjoys a base of over 32,000 registered developers, delivering an average of 100 new apps every day. There have been over 1 million downloads of the developers tools for Windows Phone 7. Trial version help you sell more Trials result in higher sales by the numbers: Users like trials  - paid apps with trial functionality are downloaded 70 times more than paid apps that don’t Nearly 1 out of 10 trial apps downloaded convert to a purchase and generate 10 times more revenue on average than paid apps that don’t include trial functionality. Trial downloads convert to paid downloads quickly. More than half of trial downloads that convert to a sale do so within the 1st 24 hours of trial download, and mostly within 2 hours of trial download. Microsoft Ad Control is gaining traction By the numbers - ad supported Windows Phone 7 apps are: Roughly ¼ of all registered U.S. WP7 developers have downloaded the free Ad SDK for Silverlight and XNA Of ad funded apps, over 95 percent use the free Microsoft Advertising Ad Control Monthly impressions from our Ad Exchange has continued to grow by double digits – impressions increased by 376 percent since January Ad Control, the first wave of “How Do I” videos are now available on MSDN: Create an Ad in a Windows Phone 7 XNA Game App Register Ad-Enabled Windows Phone 7 Apps Measure Ad Performance of Windows Phone 7 Apps Boarder International App submission for Free Apps through Yalla Apps As of today you can start submitting your free applications in developer markets that are currently not covered by Microsoft. To submit your Free application if you DO NOT belong to one of the Marketplace supported countries, go to: Yalla Apps Marketplace Policy Updates: Free App Marketplace Submission upped to 100 and other news Microsoft has been revisiting a few of our Marketplace policies based on feedback from developers to reduce friction and cost, word for word: 1. We have raised the limit on the number of certifications that can be performed for FREE apps at no cost to the registered developer from five to 100. This was a common request from developers which we are glad to implement after building alternate methods to ensure that users can find and download high quality apps. 2. We have converted policy 5.6 - related to the inclusion of contact information for support - from a mandatory to an optional policy. This is still a strongly recommended best practice, but we recognized and responded to developer feedback that this policy was creating excessive drag on the certification process for developers without commensurate user benefit for all apps. 3. We also understand the desire for clarification with regard to our policy on applications distributed under open source licenses.  The Marketplace Application Provider Agreement (APA) already permits applications under the BSD, MIT, Apache Software License 2.0 and Microsoft Public License.  We plan to update the APA shortly to clarify that we also permit applications under the Eclipse Public License, the Mozilla Public License and other, similar licenses and we continue to explore the possibility of accommodating additional OSS licenses. Enjoy and happy coding! Official Blog Post for reference.

  Read the article

• Oracle Partner Day 2012: Neue Geschäftschancen warten auf Sie!

  - by A&C Redaktion

  Wie gut kennen Sie die Neuerungen der Oracle "One Red Stack"-Unternehmensstrategie? In Zukunft werden Sie, als unser Partner, das gesamte Oracle Produktportfolio – Software, Hardware und Applications – verkaufen können! Ihr Profit: die neue Vielfalt. Toppen Sie Ihre Marktpräsenz! Erschließen Sie sich neue Märkte, neue Kundengruppen. Potenzieren Sie Ihren Erfolg in Zukunft! Maximize your Potential – das ist Ihr Stichwort für das Geschäftsjahr und unser Motto für den Oracle Partner Day am 29. Oktober 2012 in der Commerzbank Arena in Frankfurt. Erleben Sie in unseren Breakout Sessions, wo das Vertriebs-Plus für Sie liegt. Was Ihr Kunde wissen muss. Und wo Sie überzeugen können. Alle parallel laufenden Breakout Sessions werden wiederholt, damit Sie in jedem Fall daran teilnehmen können. Konzentriert auf Erfolg: das neue Oracle Alliances & Channel-Konzept Wir liefern Ihnen die entscheidenden Argumente für Kunden, die auf Nachhaltigkeit und Investitionssicherheit setzen. Für Sie, wenn Sie in Zukunft mehr erreichen wollen! Für alle, die Partner Excellence aus einer Hand anbieten können. Erfahren Sie die Produktneuheiten von der Oracle Open World (OOW) in San Francisco (30. September bis 4. Oktober 2012) aus erster Hand. In der Expert- und Partner Service-Zone finden Sie Antworten zu allen Themenschwerpunkten. Nutzen Sie dazu das neue Speed-Dating-Format, um schnell den richtigen Ansprechpartner für Ihre Fragen zu Vertrieb und Produkten zu finden. Machen Sie den Test. Wir zahlen die Testgebühr! Nutzen Sie die Gelegenheit, sich direkt zum OPN Implementation Specialist zu akkreditieren! Melden Sie sich jetzt an zum offiziellen Implementierungstest beim Testcenter Pearson Vue vor Ort beim Oracle Partner Day. Wählen Sie Ihre Fachbereiche Fusion Middleware, Applications, Hardware, Datenbank und gehen Sie als Implementierungsspezialist nach Hause. Kommen Sie zum Oracle Partner Day 2012 – aktives Partner Networking, Management Kontakte und Expertenwissen inklusive! Sichern Sie sich jetzt einen der begehrten Plätze und Ihre Teilnahme – auch am Test! Die Teilnahme ist für Sie als Oracle Partner selbstverständlich kostenfrei. Hier finden Sie weitere Informationen zum Oracle Partner Day und den Link zur Registrierung. Wir freuen uns auf Sie! Ihr Christian Werner Senior Director Alliances & Channels Germany P.S.: Direkt nach dem Oracle Partner Day findet der Oracle Day für Endkunden statt. Sie als Partner können gerne an dieser Veranstaltung gemeinsam mit Ihren Kunden teilnehmen, die Plätze sind limitiert. Hier finden Sie weitere Infos zum Oracle Day.

  Read the article

• Oracle Partner Day 2012: Neue Geschäftschancen warten auf Sie!

  - by A&C Redaktion

  Wie gut kennen Sie die Neuerungen der Oracle "One Red Stack"-Unternehmensstrategie? In Zukunft werden Sie, als unser Partner, das gesamte Oracle Produktportfolio – Software, Hardware und Applications – verkaufen können! Ihr Profit: die neue Vielfalt. Toppen Sie Ihre Marktpräsenz! Erschließen Sie sich neue Märkte, neue Kundengruppen. Potenzieren Sie Ihren Erfolg in Zukunft! Maximize your Potential – das ist Ihr Stichwort für das Geschäftsjahr und unser Motto für den Oracle Partner Day am 29. Oktober 2012 in der Commerzbank Arena in Frankfurt. Erleben Sie in unseren Breakout Sessions, wo das Vertriebs-Plus für Sie liegt. Was Ihr Kunde wissen muss. Und wo Sie überzeugen können. Alle parallel laufenden Breakout Sessions werden wiederholt, damit Sie in jedem Fall daran teilnehmen können. Konzentriert auf Erfolg: das neue Oracle Alliances & Channel-Konzept Wir liefern Ihnen die entscheidenden Argumente für Kunden, die auf Nachhaltigkeit und Investitionssicherheit setzen. Für Sie, wenn Sie in Zukunft mehr erreichen wollen! Für alle, die Partner Excellence aus einer Hand anbieten können. Erfahren Sie die Produktneuheiten von der Oracle Open World (OOW) in San Francisco (30. September bis 4. Oktober 2012) aus erster Hand. In der Expert- und Partner Service-Zone finden Sie Antworten zu allen Themenschwerpunkten. Nutzen Sie dazu das neue Speed-Dating-Format, um schnell den richtigen Ansprechpartner für Ihre Fragen zu Vertrieb und Produkten zu finden. Machen Sie den Test. Wir zahlen die Testgebühr! Nutzen Sie die Gelegenheit, sich direkt zum OPN Implementation Specialist zu akkreditieren! Melden Sie sich jetzt an zum offiziellen Implementierungstest beim Testcenter Pearson Vue vor Ort beim Oracle Partner Day. Wählen Sie Ihre Fachbereiche Fusion Middleware, Applications, Hardware, Datenbank und gehen Sie als Implementierungsspezialist nach Hause. Kommen Sie zum Oracle Partner Day 2012 – aktives Partner Networking, Management Kontakte und Expertenwissen inklusive! Sichern Sie sich jetzt einen der begehrten Plätze und Ihre Teilnahme – auch am Test! Die Teilnahme ist für Sie als Oracle Partner selbstverständlich kostenfrei. Hier finden Sie weitere Informationen zum Oracle Partner Day und den Link zur Registrierung. Wir freuen uns auf Sie! Ihr Christian Werner Senior Director Alliances & Channels Germany P.S.: Direkt nach dem Oracle Partner Day findet der Oracle Day für Endkunden statt. Sie als Partner können gerne an dieser Veranstaltung gemeinsam mit Ihren Kunden teilnehmen, die Plätze sind limitiert. Hier finden Sie weitere Infos zum Oracle Day.

  Read the article

• mongoDB Management Studio

  - by Liam McLennan

  This weekend I have been in Sydney at the MS Web Camp, learning about web application development. At the end of the first day we came up with application ideas and pitched them. My idea was to build a web management application for mongoDB. mongoDB I pitched my idea, put down the microphone, and then someone asked, “what’s mongo?”. Good question. MongoDB is a document database that stores JSON style documents. This is a JSON document for a tweet from twitter: db.tweets.find()[0] { "_id" : ObjectId("4bfe4946cfbfb01420000001"), "created_at" : "Thu, 27 May 2010 10:25:46 +0000", "profile_image_url" : "http://a3.twimg.com/profile_images/600304197/Snapshot_2009-07-26_13-12-43_normal.jpg", "from_user" : "drearyclocks", "text" : "Does anyone know who has better coverage, Optus or Vodafone? Telstra is still too expensive.", "to_user_id" : null, "metadata" : { "result_type" : "recent" }, "id" : { "floatApprox" : 14825648892 }, "geo" : null, "from_user_id" : 6825770, "search_term" : "telstra", "iso_language_code" : "en", "source" : "&lt;a href=&quot;http://www.tweetdeck.com&quot; rel=&quot;nofollow&quot;&gt;TweetDeck&lt;/a&gt;" } A mongodb server can have many databases, each database has many collections (instead of tables) and a collection has many documents (instead of rows). Development Day 2 of the Sydney MS Web Camp was allocated to building our applications. First thing in the morning I identified the stories that I wanted to implement: Scenario: View databases Scenario: View Collections in a database Scenario: View Documents in a Collection Scenario: Delete a Collection Scenario: Delete a Database Scenario: Delete Documents Over the course of the day the team (3.5 developers) implemented all of the planned stories (except ‘delete a database’) and also implemented the following: Scenario: Create Database Scenario: Create Collection Lessons Learned I’m new to MongoDB and in the past I have only accessed it from Ruby (for my hare-brained scheme). When it came to implementing our MongoDB management studio we discovered that their is no official MongoDB driver for .NET. We chose to use NoRM, honestly just because it was the only one I had heard of. NoRM was a challenge. I think it is a fine library but it is focused on mapping strongly typed objects to MongoDB. For our application we had no prior knowledge of the types that would be in the MongoDB database so NoRM was probably a poor choice. Here are some screens (click to enlarge):

  Read the article

• The Case of the Missing Date/Time Stamp: Reporting Services 2008 R2 Snapshots

  - by smisner

  This week I stumbled upon an undocumented “feature” in SQL Server 2008 R2 Reporting Services as I was preparing a demonstration on how to set up and use report snapshots. If you’re familiar with the main changes in this latest release of Reporting Services, you probably already know that Report Manager got a facelift this time around. Although this facelift was generally a good thing, one of the casualties – in my opinion – is the loss of the snapshot label that served two purposes… First, it flagged the report as a snapshot. Second, it let you know when that snapshot was created. As part of my standard operating procedure when demonstrating report snapshots, I point out this label, so I was rather taken aback when I didn’t see it in the demonstration I was preparing. It sort of upset my routine, and I’m rather partial to my routines. I thought perhaps I wasn’t looking in the right place and changed Report Manager from Tile View to Detail View, but no – that label was still missing. In the grand scheme of life, it’s not an earth-shattering change, but you’ll have to look at the Modified Date in Details View to know when the snapshot was run. Or hope that the report developer included a textbox to show the execution time in the report. (Hint: this is a good time to add this to your list of report development best practices, whether a report gets set up as a report snapshot or not!) A snapshot from the past In case you don’t remember how a snapshot appeared in Report Manager back in the old days (of SQL Server 2008 and earlier), here’s an image I snagged from my Reporting Services 2008 Step by Step manuscript: A snapshot in the present A report server running in SharePoint integrated mode had no such label. There you had to rely on the Report Modified date-time stamp to know the snapshot execution time. So I guess all platforms are now consistent. Here’s a screenshot of Report Manager in the 2008 R2 version. One of these is a snapshot and the rest execute on demand. Can you tell which is the snapshot? Consider descriptions as an alternative So my report snapshot demonstration has one less step, and I’ll need to edit the Denali version of the Step by Step book. Things are simpler this way, but I sure wish we had an easier way to identify the execution methods of the reports. Consider using the description field to alert users that the report is a snapshot. It might save you a few questions about why the data isn’t up-to-date if the users know that something changed in the source of the report. Notice that the full description doesn’t display in Tile View, so keep it short and sweet or instruct users to open Details View to see the entire description.

  Read the article

• Apache - create multiple aliases

  - by mc3mcintyre

  I'm trying to setup two websites on my Apache server. One is www.domain.com and the other is test.domain.com. Currently, my 000-default.conf file reads as follows: <VirtualHost www:80> # The ServerName directive sets the request scheme, hostname and port that # the server uses to identify itself. This is used when creating # redirection URLs. In the context of virtual hosts, the ServerName # specifies what hostname must appear in the request's Host: header to # match this virtual host. For the default virtual host (this file) this # value is not decisive as it is used as a last resort host regardless. # However, you must set it for any further virtual host explicitly. #ServerName www.domain.com #ServerAlias www ServerAdmin [email protected] DocumentRoot /var/www/domain.com/ # Available loglevels: trace8, ..., trace1, debug, info, notice, warn, # error, crit, alert, emerg. # It is also possible to configure the loglevel for particular # modules, e.g. #LogLevel info ssl:warn ErrorLog ${APACHE_LOG_DIR}/domain.error.log CustomLog ${APACHE_LOG_DIR}/domain.access.log combined UseCanonicalName on allow from all Options +Indexes # For most configuration files from conf-available/, which are # enabled or disabled at a global level, it is possible to # include a line for only one particular virtual host. For example the # following line enables the CGI configuration for this host only # after it has been globally disabled with "a2disconf". #Include conf-available/serve-cgi-bin.conf </VirtualHost> <VirtualHost test:80> DocumentRoot "/var/www/domain.com/test/" ServerName test.domain.com ServerAdmin [email protected] ErrorLog ${APACHE_LOG_DIR}/test.domain.error.log CustomLog ${APACHE_LOG_DIR}/test.domain.access.log combined UseCanonicalName on allow from all Options +Indexes </VirtualHost> # vim: syntax=apache ts=4 sw=4 sts=4 sr noet As is, when I use a browser to go to the www location, it show me a directory listing. However, if I remove the www:80 on Line 1 and replace it with *:80, it correctly displays the webpage. I don't understand why. Can anyone help me configure this 000-default.conf file so that www goes to "/var/www/domain.com" and that test goes to "/var/www/domain.com/test"? Thank you.

  Read the article

• It's Here! Visual Studio 2010 and ASP.NET 4.0 Ship

  Today Microsoft released Visual Studio 2010 and ASP.NET 4.0. I've been using the RC version of Visual Studio 2010 quite a bit for the past couple of months and have really grown to like it. It has a host of features and enhancements that improve developer productivity, from improved IntelliSense to better multiple monitor support. Plus there's something about the user experience that, to me, makes it feel better than Visual Studio 2008. I don't know if it's the new blue color motif or what, but the IDE seems more modern looking and more responsive to my mouse movements and other input. Anyway, if you've not yet downloaded Visual Studio 2010 and ASP.NET 4.0, why not? As with previous versions of Visual Studio there's a free Express Edition and VS2010 and ASP.NET 4.0 runs side-by-side with earlier versions of Visual Studio and ASP.NET. And with Visual Studio 2010's multi-targeting you can even use VS2010 as your development editor for ASP.NET 2.0 and ASP.NET 3.5 web applications. (Although be forewarned if you have multiple developers working on the application that the project files in VS2010 and earlier versions of Visual Studio differ.) This week's article on 4Guys explores my favorite new features of Visual Studio 2010. Here's an excerpt: The Visual Studio 2010 user experience is noticeably different than with previous versions. Some of the changes are cosmetic - gone is the decades-old red and orange color scheme, having been replaced with blues and purples - while others are more substantial. For instance, the Visual Studio 2010 shell was rewritten from the ground up to use Microsoft's Windows Presentation Foundation (WPF). In addition to an updated user experience, Visual Studio introduces an array of new features designed to improve developer productivity. There are new tools for searching for files, types, and class members; it's now easier than ever to use IntelliSense; the Toolbox can be searched using the keyboard; and you can use a single editor - Visual Studio 2010 - to work on. This article explores some of the new features in Visual Studio 2010. It is not meant to be an exhaustive list, but rather highlights those features that I, as an ASP.NET developer, find most useful in my line of work. Read on to learn more! And, in closing, here are some helpful VS2010 and ASP.NET 4.0 links: One click installation for ASP.NET 4.0, Visual Web Developer 2010, .NET Framework 4.0, and ASP.NET MVC 2 Eight Quick Hit videos showing some of the cool new VS2010 features VS2010 and ASP.NET 4.0 Release Announcement with some great info/links from none other than Scott Guthrie Happy Programming!Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• SEO to ensure visibility for a narrow, non-competitive, non-commercial site

  - by hen3ry

  I'm webmaster of a non-commercial site in English. A non-native-English speaker asked me why our site doesn't produce hits in Google searches she conducts for relevant keywords in her native language. I asked her for a list of keywords in her native language, and I naively tried inserting those into the META info in the page headers and waited a couple of weeks. No help. A little searching informed me that Google doesn't use the META info, and has not done so for a very long time. D'oh! To be entirely concrete, suppose the StackExchange folks want Russian speakers to find this site, Pro Webmasters. The direct translation in Russian of "webmaster" --thanks, Google Translator-- is: "?????????". (Not sure this will render properly, but that's not essential to my question.) Assuming Pro Webmasters has a common template for all pages it generates, inserting "?????????" into the Keywords META for that template won't help, it seems. What could StackExchange do to make this site visible to users searching with the Russian keyword "?????????" ? Pretty much all the advice I've seen boils down to this, if I understand correctly: use the desired search term often (but not too often) among site content, and the problem will be solved. That's great, but I don't think sprinkling "?????????" visibly all over Pro Webmasters is going to fly. Just for completeness, crawlers must be long immune to the invisible-to-visitors scheme, e.g, format "?????????" in a tiny text size in a color the same as an existing background, e.g. white-over-white. Or, put that text inside a div styled: ' style="visibility: hidden" '. Probably some other equivalents. I can only think of one slightly effective method, along these lines: place an unobtrusive link on the common template to a page titled "for international users" , and on that page list desired synonyms for "webmaster" in various languages on that page. A test case --admittedly, just one-- using my site implies that a Google search for "international users" ????????? will produce a hit for this page, and thus make the site minimally visible, despite the fact that the page will almost never be visited. At the moment, anyway. Note: All the SEO discussions I have found so far are about competitive and --almost certainly-- commercial sites. To repeat: my site is non-commercial, and it is about an obscure, narrow topic that is of interest to only a small number of people worldwide. This isn't about clawing our way to the top of competitive rankings, just making this content minimally visible to interested non-native-English speakers. Ideas? TIA

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >