Search Results

Search found 65721 results on 2629 pages for 'set options'.

Page 67/2629 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Can't set acl for afs even though i'm in the right group

  - by Torandi

  I've got a dir that i've lost controll over in an afs system. According to the system adminstrators my adminin subgroup (dsekt:admin) got rlidwka on the dir. I'm a member of this group (and i can list the members of the group and see my nick there) though I can't set the acl's for the dir. The pts: $pts membership dsekt:admin Members of dsekt:admin (id: -6813) are: /.../ taran And my klist. $>klist Credentials cache: FILE:/tmp/krb5cc_56782 Principal: [email protected] Both dsekt:admin and the dir is on the NADA.KTH.SE node.

  Read the article

• Set Display Refresh Rate in OSX w/o External Utilities

  - by codedonut

  I have an iMac and an LG Flatron connected as a secondary monitor. The recommended resolution for the flatron is 1680x1050 @ 65.290 Hz (horiz), 59.954 Hz (vert). For some reason, OSX is choosing a slightly different set of scan rates and this is currently my best guess of why the monitor goes into power saving mode when connected to the iMac (but works fine on a PC). Now, I resolved this by installing switchResX and fudging the scan rates according to the specs in the manual. But how does one change these rates w/o 3rd party tools? Which config files need editing? Thanks

  Read the article

• How to set robots.txt globally in nginx for all virtual hosts

  - by anup

  I am trying to set robots.txt for all virtual hosts under nginx http server. I was able to do it in Apache by putting the following in main httpd.conf: <Location "/robots.txt"> SetHandler None </Location> Alias /robots.txt /var/www/html/robots.txt I tried doing something similar with nginx by adding the lines given below (a) within nginx.conf and (b) as include conf.d/robots.conf location ^~ /robots.txt { alias /var/www/html/robots.txt; } I have tried with '=' and even put it in one of the virtual host to test it. Nothing seemed to work. What am I missing here? Is there another way to achieve this?

  Read the article

• Excel 2007: Using a time to set XY chart axis scaling like in 2003

  - by CookieOfFortune

  In Excel 2003, when you created a XY chart using time as an axis, you could set the scaling of these axes by typing in the date. In Excel 2007, you have to use the decimal version of the time (eg. How many days since some arbitrary earlier date). I was wondering if there was a way to avoid having to make such a calculation? A developer posted on a blog that this issue would be fixed in a future release, but all versions of Excel 2007 I have tried have not resolved this issue. The relevant quote: Those of you familiar with this technique of converting time to a decimal may recall that Excel 2003 allowed you to enter a date and time like “1/1/07 11:00 AM” directly in the axis option min/max fields and Excel would calculate the appropriate decimal representation. This currently does not work in Excel 2007 but will be fixed in a subsequent release.

  Read the article

• Set up ad hoc wireless connection between Windows Vista and Mac OS X

  - by Skarab

  I have the following problem - Windows Vista does not connect to adhoc wireless network created on my Macbook. I have tried to create secured (with 40 bit key) and unsecured network but Windows Vista still has problems to connect. Windows VISTA informs me -- after 5 minutes of attempts - that setting up the connection -- with my adhoc network -- took too much time. My question: do I need to configure some settings on Vista to connect it to my Macbook? Maybe it is a problem with DHCP? Edited: I have tried the other way: http://superuser.com/questions/202890/set-up-an-adhoc-network-in-windows-vista-to-connect-to-and-share-the-internet-con

  Read the article

• How to set up an SSL Cert with Subject Alternative Name

  - by Darren Oster

  To test a specific embedded client, I need to set up a web server serving a couple of SSL (HTTPS) sites, say "main.mysite.com" and "alternate.mysite.com". These should be handled by the same certificate, with a Subject Name of "main.mysite.com" and a Subject Alternative Name of "alternate.mysite.com". This certificate needs to be in an authority chain back to a 'proper' CA (such as GoDaddy, to keep the cost down). My question is, are there any good tutorials on how to do this, or can someone explain the process? What sort of parent certificate do I need to purchase from the CA provider? My understanding of SSL certificates is limited, but as Manuel said in Fawlty Towers, "I learn...". I'm happy to work in Windows (IIS) or Linux (Apache) (or even OSX, for that matter). Thanks in advance.

  Read the article

• Redhat doesn't set my desired hostname on reboot

  - by tomdee

  I have a redhat (EL5) server that I need to change the hostname on. I'm trying to put it back into a known state to help with server provisioning activities. As part of changing the hostname, I'm updating /etc/sysconfig/network and /etc/hosts. I also have an explicit call to hostname. My desired state is that the server thinks its hostname is "localhost". And a call to "hostname" returns "localhost". The problem I'm having is that when I reboot, the hostname is reverted to "localhost.companyname.com" which is not what I want. How do I ensure that the hostname is set up as just "localhost" when I reboot? My /etc/sysconfig/network file contains: NETWORKING=yes HOSTNAME=localhost GATEWAY=123.123.123.123 #I do have a proper IP address here My /etc/hosts file contains: 127.0.0.1 localhost.localdomain localhost 172.21.1.1 localhost.companyname.com localhost

  Read the article

• Cannot set "Language for Non-Unicode Programs" in Regional and Language Settings

  - by cornjuliox

  I'm trying to set the Language for Non-Unicode Programs from English to Japanese (I'm using Windows XP SP 3), but it won't let me. It looks like I've got the East Asian Language packs installed, but when I select "Japanese" from the drop-down box and hit "Apply" I get an error that says "Setup was unable to install the chosen locale. Please contact your system administrator". I'm already logged in as the administrator, and I've restarted several times but it still won't let me. Can anyone give me an idea as to how to solve this problem? Reinstalling Windows is absolutely out of the question.

  Read the article

• How to set Brocade 200E SAN Fabric Switch Port Health Monitoring to "monitored"

  - by Kenny

  Hi, I have a Brocade SAN Fabric Switch, a 200E. When using the web based management interface "SwitchExplorer" I can click the port, and I see "Port Administration Services". In the first screen of data that appreas, there's a row called "Health" which has value "Unmonitored". Do you know how to set this port to be Monitored? And if also - what "Health" monitoring does? I'm hoping it'll email or log if there's a connection or disconnection.. Many thanks for looking... Kenny

  Read the article

• Trying to set up OpenVPN server on a vps

  - by Austin

  I'm trying to set up an OpenVPN server on my VPS for myself when I'm in public places, using this tutorial, http://tipupdate.com/how-to-install-openvpn-on-ubuntu-vps/ However whenever I try to start the server, it gives me this, root@vps:~# /etc/init.d/openvpn start * Starting virtual private network daemon(s)... * Autostarting VPN 'server' [fail] The log contains this Tue Dec 11 10:53:32 2012 Diffie-Hellman initialized with 1024 bit key Tue Dec 11 10:53:32 2012 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue Dec 11 10:53:33 2012 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue Dec 11 10:53:33 2012 ROUTE: default_gateway=UNDEF Tue Dec 11 10:53:33 2012 Note: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2) Tue Dec 11 10:53:33 2012 Note: Attempting fallback to kernel 2.2 TUN/TAP interface Tue Dec 11 10:53:33 2012 Cannot allocate TUN/TAP dev dynamically Tue Dec 11 10:53:33 2012 Exiting So obviously it's something to do with the tun, but I don't understand how to fix it. Thanks!

  Read the article

• How do I set "relay_hosts_only" setting using sendmail / m4

  - by Dave

  We're using CentOS and sendmail's m4 configuration. How do I set domains where emails should be delivered? I only want two domains, and would like email to all other domains blocked. I tried this in my "/etc/mail/sendmail.mc" file ... FEATURE(`relay_hosts_only,mydomain1.com,mydomain2.com')dnl But then got this error tryiing to generate the sendmail.cf file ... [dalvarado@mymachine ~]$ sudo m4 /etc/mail/sendmail.mc > /etc/mail/sendmail.cf m4:/etc/mail/sendmail.mc:156: Warning: excess arguments to builtin `include' ignored m4:/etc/mail/sendmail.mc:156: cannot open `/usr/share/sendmail-cf/feature/relay_hosts_only': No such file or directory Thanks for your advice, - Dave

  Read the article

• Set default open-with app to a Python program on a Mac

  - by Vincent

  I use the open source application UliPad to edit restructured text files (rst). It is a Python application that I launch via Terminal like so: python32 UliPad.py I have python32 as an alias to the 32bit install of Python on my machine. I have several versions installed. First I would like a way to launch UliPad like other OS X apps. Not really sure how to do this. Secondly, I would like to set all .rst files to be opened with UliPad.py. Is there a way to do this? I know how to choose the default app in Finder but not sure how to choose UliPad as that app.

  Read the article

• Why can't I create an Alias Resource Record Set for an EC2 instance

  - by praterade

  I have been working with AWS for over a year, setting up EC2 instances, domains, ELBs, etc. When I want to assign a subdomain to an EC2 instance, I have to create an elastic IP (that I pay for), then assign a CNAME record to that elastic IP. When I want to assign a subdomain to an ELB (load balancer) instance, I just create an alias resource record set to the ELB. I've read over the docs and don't understand why AWS doesn't support aliasing to instances. Am I missing a key concept here? Wouldn't it be simpler to just alias EC2 instances and skip the whole elastic IP bit?

  Read the article

• Set up ad hoc wireless connection between Windows Vista and Mac OS X

  - by Skarab

  I have the following problem - Windows Vista does not connect to adhoc wireless network created on my Macbook. I have tried to create secured (with 40 bit key) and unsecured network but Windows Vista still has problems to connect. Windows VISTA informs me -- after 5 minutes of attempts - that setting up the connection -- with my adhoc network -- took too much time. My question: do I need to configure some settings on Vista to connect it to my Macbook? Maybe it is a problem with DHCP? Edited: I have tried the other way: http://superuser.com/questions/202890/set-up-an-adhoc-network-in-windows-vista-to-connect-to-and-share-the-internet-con

  Read the article

• How to set up wireless access on a Cisco router

  - by Carlos

  Hi, I've set up my 877W according to the configuration listed in this forum post: IPTV over Cisco 877 (It's the working configuration at the bottom of the post) Note that I have an 877W, so it also has a wireless radio. Now, I've gotten the whole setup to work, so IPTV is working, and I can access the internet via the ethernet ports. Now I'm trying to figure out how to allow access via the dot11radio interface. I've gathered that I basically need to create a bridge group, and bridge the radio to the internet VLAN. However, when I add a bridge-group 2 command to VLAN1, it seems to take down the whole internet VLAN. (The IPTV continues to work.) This makes the router itself inaccessible (I've got a laptop, so no serial) and I end up having to reboot the router. Can anyone tell me how to a) Allow wireless access to the internet (preferably with WEP, to match my old router) b) Determine what makes the router inaccessible when I add the new bridge group c) Forward the IPTV traffic onto a machine on my internet VLAN

  Read the article

• How to set path of Virtual PC hard disk differencing parent

  - by Barry Kelly

  I have an old Windows XP Mode vhd backed up from my previous system, but I'm having difficulty getting it running on the new system. The vhd is a differencing disk, and its parent is the standard Windows XP Mode base; I still have the old parent, and have verified it is binary identical to the XP Mode base in my new installation of XP Mode. But in the new system, the path to the differencing disk parent is different than the old. When I open up the settings for the .vmcx for my old XP mode, and select "Hard Disk 1", the "Virtual hard disk file" is set correctly, but the "Parent Disk:" field is pointing at the wrong path, and I can't see any way to edit it. Does anyone know how?

  Read the article

• Set Error-Pages for all Applications in Tomcat

  - by phisch

  I'm trying to set up custom error pages in tomcat 6, because I don't want the default ones to show up. My error pages are static html, no jsp or anything dynamic. I know how to do this through the web.xml in each application but I'd prefere to setup the error pages only once for the entire server. I tried to add the following fragment to the global web.xml (in conf), but no matter what I add under location, it does not show. <error-page> <error-code>404</error-code> <location>/404.html</location> </error-page> What do I need to do to gobally define custom error pages? Thanks!

  Read the article

• Deploy Windows 7 Backup set to Windows 8

  - by Matthias

  Situation: We have a laptop here that's completely fubar. I.e: The hard drive is filled to the brim with bad sectors. Luckily, backups have been made using the built-in Windows 7 backup feature. This produces folders named Backup Set 2012-11-09 003009, containing folders like Backup Files 2012-11-09 003009, containing zip-files like Backup files 1, 2, 3,... Our brand new laptop comes with Windows 8. Now: Can we, using the standard back-up and restore feature in Windows 8, restore all the documents, music, etc. using the Windows 7 backup files? Thanks. (FYI: We also took a normal backup of all the documents just to be sure of course. I'm just curious what would happen. I would test it out, but the new laptop hasn't arrived yet and I wanted to make sure my efforts would not be in vain.)

  Read the article

• Help me to set samba and apache on my Ubuntu VM from Vista, starting from ping

  - by avastreg

  Ok the title is not so clear after all, so let's start with the problem description posting some points: i'm on Win Vista i have a Virtual Box Ubuntu 9.04 server (Virtual Machine) installed in windows i'm under Active Directory (maybe helps), with network 192.168.2.x After Ubuntu installation (LAMP), i have: Ubuntu Ip set to 10.0.2.15 (dhcp) Vista pings Ubuntu and Ubuntu pings Vista (only IPs, not names) Can't connect to Apache (default install ubuntu server) at the url h**p://10.0.2.15/ On Ubuntu, testing Apache by doing 'wget http://10.0.2.15/' works Tried to setup samba, writing a share def, but nothing, i can't access from Vista to Ubuntu My scope is: Setting up samba to work on files from windows Reaching apache to test web pages Ok i'm not completely noob (but i'm on the noob way anyway) and i've tried many solutions, so please try to help me; let's look together what went wrong :)

  Read the article

• How to set up a staging apt repository to securely manage upgrades

  - by andreash

  Hello, I would like to be able to run automatic apt-get upgrade (once per hour) on our servers (Ubuntu 10.04), so that I don't have to do it manually on all of them (about 15). However, for production machines, that's not a good idea ... So here's my idea: Set up a local repository for all 'approved' updates for critical packages. I would then push updated packages from upstream to our local repo after I tested them, and all servers could automatically (apt-cron?) upgrade from this repository. So my question is this: How do I configure apt on the clients so that they use the local repository only for all packages which exist on the local repository, and the upstream one for all other packages? Does this actually make sense? Or am I missing something? Anyways, thanks for your insight! Andreas.

  Read the article

• set tap0 using virt-manager for bridged wireless

  - by DaveO

  After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

  Read the article

• VMWare Server :: VM set to 2gb RAM but vmware process shows 100mb physical, 1900mb virtual

  - by brad

  I've set up a VMWare instance to run CastIron Integration Appliance. I allocated 2gb of memory to the instance, assuming it would take this as physical memory (my server has 8gb total). When I view top however on the server, the vmware-vmx process has about 100m Resident memory and 1900m Virtual. Running CastIron it reports that the appliance often hits 50% memory usage. Does this mean I'm using 900mb of harddrive space as memory? I wanted VMWare to use 2gb of physical memory, no swap. Can anyone tell me how to achieve this? Setup Debian Lenny 5.0.3 VMWare Server 2.0.2

  Read the article

• Postfix SMTP sends to localhost, ignores MX records set to Google Apps

  - by Kerrick

  I have the MX records for zaltin.com set to the Google Apps domains (aspmx.l.google.com etc.). If an email is sent to [email protected] from most places, it goes to my Google Apps account. However, on the zaltin.com server (Ubuntu 10.04 if it matters), sending via SMTP (postfix), if I send to [email protected] (via the Pony ruby gem if it matters), it simply routes to kerrick@localhost (showing up via the mail command) instead of going to my Google Apps account (where it should show up in my GApps Gmail inbox). Can I make email sent via SMTP on my server, through my server, not go to my server but to Google Apps?

  Read the article

• Determine / set Puppet environment

  - by quickshiftin

  I'm trying to determine what Puppet thinks the environment is on my agent nodes. Per the documentation I've configured the agent's environment in /etc/puppet/puppet.conf as such [agent] environment = development In order to view the environment I've found this code to add an environment fact to facter: require 'puppet' Facter.add("environment") do setcode do Puppet[:environment] end end However, on one of my agent nodes, if I run sudo facter -p environment, the result is production. I've tried to manually set the environment temporarily via sudo puppet agent --environment development, however the result from facter is the same. Any idea what's going on?

  Read the article

• samba - join domain - automatically set workgroup

  - by ftiaronsem

  Hell alltogether Since I have to do this often, I want to automate the joining to a windows domain as much as possible. While joining a domain one has to specify realm = in the /etc/smb.conf, along with some other settings like security=ads. Among these settingst there is workgroup = My question is: Is it possible to fill this field automatically by samba, while joining a domain? Normally I would just have said never, but as I tried leaving this field blank while joining a domain, i got: Failed to join domain: Invalid configuration ("workgroup" set to '', should be 'BLABLA') and configuration modification was not requested This has made me wondering whether an automatic modification is possible and if so how? A search on the internet and the man page brought no results. It would be really great, if someone could answer that. Thanks in advance ftiaronsem

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >