Search Results

Search found 2299 results on 92 pages for 'alec smart'.

Page 68/92 | < Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >

  • BGP Multipath & return routes

    - by Dennis van der Stelt
    I'm probably a complete n00b concerning serverfault related questions, but our IT department makes a bold statement I wish to verify. I've searched the internet, but can find nothing related to my question, so I come here. We have Threat Management Gateway 2010 and we used to just route the request to IIS and it contained the ip address so we could see where it was coming from. But now they turned on "Requests apear to come the TMG server" so ip addresses aren't forwarded anymore. Every request has the ip of the TMG server. Now the idea behind this is that because of multipath bgp routes, the incoming request goes over RouteA, but the acknowledgement messages could return over RouteB. The claim is that because the request doesn't come from the first known source, our proxy, but instead from IIS, some smart routers at the visitor of our websites don't recognize the acknowledgement message and filter it out. In other words, the response never arrives. Again, this is the claim. But I cannot find ANY resources on the internet that support this claim. I do read about bgp multipath, but more in the case that there are alternative routes when the fastest route fails for some reason. So is the claim completely bogus or is there (some) truth to it? Can someone explain or point me to resources? Thanks in advance!

    Read the article

  • Unable to access stackexchange sites from this system

    - by Sandeepan Nath
    Earlier, I was not able to access most of the stackexchange sites like stackoverflow, programmers.SE etc. on my home Windows XP system. I was able to access only a few like http://meta.stackexchange.com and not even http://www.meta.stackexchange.com (note the www). I tried many other sites like http://www.stackoverflow.com, http://area51.stackexchange.com/ but was getting page not found errors on all browsers. Even pinging from terminal was saying destination host unreachable. I did not check recently but may be all SE sites are unreachable now. I was clueless about what could be the issue. I thought some firewall issue? So, I stopped AVG antivirus's firewall, then completely uninstalled it and even turned of windows firewall. But still not reachable even after fresh installation of Windows 7. Then I noticed a "Too many requests" notice on google. This page - http://www.google.co.in/sorry/?continue=http://www.google.co.in/# I don't know why this appeared but I guess somehow too many requests might have been sent to these sites and they blocked me. But in that case, SE would be smart enough to show a captcha like google. So, how to confirm the problem and fix it. Similar questions like these don't look solved yet - Unable to access certain websites Unable to Access Certain Websites I have lately started actively participating in lots of SE sites. There are new new questions popping up in my mind every time and I am not able to ask them. Please help! Thanks

    Read the article

  • Why is /usr/bin/env permission denied to rails server?

    - by Eric Hopkins
    I've just set up rails on an apache server running on Ubuntu, and when I try to go to the root page it gives this error: /usr/bin/env: bash: Permission denied env and all the directories in the path all have permissions 755. I tried setting env to have permissions 777 but still got the same error. Rails is running as "nobody". Why is this happening? I don't know what else to try. In /etc/apache2/sites-available/api.conf: <VirtualHost *:80> ServerName api.thinknation.ca ServerAlias api.thinknation.ca DocumentRoot /var/www/api/public ErrorLog /var/www/logs/error.log CustomLog /var/www/logs/access.log combined RailsSpawnMethod smart <Directory /var/www/api/public> # This relaxes Apache security settings. AllowOverride all # MultiViews must be turned off. Options -MultiViews -Indexes # Uncomment this if you're on Apache >= 2.4: Order allow,deny Allow from all #Require all granted </Directory> </VirtualHost> From config/database.yml in my rails directory (with sensitive user names and passwords omitted): default: &default adapter: mysql2 encoding: utf8 pool: 5 username: root password: socket: /var/run/mysqld/mysqld.sock development: <<: *default database: api_development test: <<: *default database: api_test production: <<: *default url: <%= ENV['DATABASE_URL'] %> database: api username: ------------ password: ------------ Not sure what other details or files are relevant, I will add them if needed.

    Read the article

  • sendmail relay status

    - by Andy
    Hello all, I have a RHEL3 server with sendmail configured to relay mail to: # "Smart" relay host (may be null) DSmailrelay This relay server is an exchange server not administered by me. A few days ago its IP address was changed without my knowledge so I've updated the correct ip in /etc/hosts for the mail relay entry. Unfortunately no mail is currently going through and maillog reports: Oct 26 14:32:39 fsimag sendmail[12580]: n9Q3VxPA012580: from=root, size=3685, class=0, nrcpts=1, msgid=<~R.*.2009102614315955@*>, relay=root@localhost Oct 26 14:32:39 fsimag sendmail[12580]: n9Q3VxPA012580: to=wodwest@*.net, delay=00:00:40, mailer=esmtp, pri=33685, dsn=4.4.3, stat=queued Oct 26 14:36:09 fsimag sendmail[13670]: n9Q3ZTcf013670: from=root, size=5831, class=0, nrcpts=1, msgid=<~R.medicus.2009102614352914@*>, relay=root@localhost Oct 26 14:36:09 fsimag sendmail[13670]: n9Q3ZTcf013670: to=tsgastro@(.net, delay=00:00:40, mailer=esmtp, pri=35831, dsn=4.4.3, stat=queued Oct 26 14:36:50 fsimag sendmail[13882]: n9Q3aAxj013882: from=root, size=5830, class=0, nrcpts=1, msgid=<~C.medicus.2009102614361009@*>, relay=root@localhost Oct 26 14:36:50 fsimag sendmail[13882]: n9Q3aAxj013882: to=elmwood@*.net, delay=00:00:40, mailer=esmtp, pri=35830, dsn=4.4.3, stat=queued (With domains obscured) The mailq command shows nothing, and I've also tried connecting to this new mail server via telnet and manually sending and reports as being queued but not sent. The administrator of this machine has put it back to me saying he sees no problems, and I just want to cover everything before passing it back to him. Is there any other tests/logs/reasons for sendmail to only report it as "stat=queued" ? I've looked in previous logs and the relay is set to root@localhost in those but none were ever set to queued. Thanks for any help, Andy

    Read the article

  • Router and Switch VLAN Configuration for Isolated Network

    - by Ben
    I haven't worked with VLANs much in the past and I was hoping if I could get a good explanation of what I need to setup for this to work. I have a Netgear WNR2000v2 router and a Netgear GS108T smart switch currently in my network. The fourth port on the router connects to port one on the switch. I would like to be able to isolated port 8 on the switch for use as a "guest port" when I bring home malware infested PCs for repair. I figured the VLAN capabilities of the GS108T would be able to do this for me, but I think I have a misunderstanding of how the VLAN actually works. Port 8 needs internet access but should not be able to communicate with the rest of the PCs on the home network. The subnet for the home network is 192.168.1.0/24 and I would like the guest PC to have A) 192.168.1.64 or B) 192.168.2.2. I am reading a lot of stuff about port trunking and VLAN membership, but I am confused as to which setup needs to be in place to make this work. Any help is greatly appreciated! Let me know if there is more information I need to provide. Definitely looking to learn something from this project. Thanks!

    Read the article

  • Mac Security - Which one?

    - by Bob Rivers
    Hi, Recently I had my credit card cloned. A few hours after shopping at an online store (in which I trust and buy since 2006) I received a call from my bank asking if I recognize a $5,000 debt to a store(?!) called Church of Christ... I'm a Mac user (OS X 10.6.3). I always kept my system updated and I have firewall enabled (in my Mac and in my broadband router), but I decided to adopt some kind of protection. I don't want to rise passionate discussions. Real or not, snake oil or not, I need to have back my peace of mind... I read this and this posts. I selected two software that I think that could help me (both have more features other than just an antivirus). Does someone have feedback about Intego's VirusBarrier X6 or Trendmicro's Smart Surfing? Intego solutions seems to be better, but TrendMicro brand/name is stronger in corporate environment, so their solution should be good. Both solutions have 30 day free trial, but I would like to hear something from you. Any other solution that I should look? TIA, Bob

    Read the article

  • Windows 7 doesn't boot when second hard disk is connected

    - by kenshin9786
    I'm sorry for my bad english on beforehand. I have two hard disks, one SATA and another IDE. I have windows XP and 7 on the SATA one, and Ubuntu on the IDE. Both of them boots and works, bios recognizes them, just works. After I installed Windows 7, and connected the IDE drive, it freezes on "Starting Windows" (the black screen with the Windows logo). I unplug the IDE drive, and it starts normally. Windows XP starts normally on both situations (with or without the IDE one connected), same for Ubuntu (it works with both disks connected or just the IDE where it is). The IDE drive is on good status according to SMART. The IDE is first on boot order. It goes to the Ubuntu's grub first, then by default it goes to the Windows 7 bootloader, and then to XP. I think the problem is not about the bootloader or grub. I just read that it can be solved formatting the "problematic" hard disk because Windows 7 cannot handle so many active partitions or something like that. But that's not an option for me, I don't want to lose my Ubuntu nor have it unbootable. How can I solve this without this consecuences I mentioned? Any help would be appreciated.

    Read the article

  • postfix concurrency limit with round robin dns

    - by goose
    Take the following internal round robin dns setup mymta.com. IN A 172.31.1.1 mymta.com. IN A 172.31.1.2 mymta.com. IN A 172.31.1.3 mymta.com. IN A 172.31.1.4 mymta.com. IN A 172.31.1.5 mymta.com. IN A 172.31.1.6 mymta.com. IN A 172.31.1.7 mymta.com. IN A 172.31.1.8 mymta.com. IN A 172.31.1.9 mymta.com. IN A 172.31.1.10 Now assume the following postfix setup (assume these are the only tweaks from defaults in debian package) main.cf: smtp_connection_cache_destinations = mymta.com smtp_connection_cache_reuse_limit = 750 smtp_destination_concurrency_limit = 75 transport * :[mymta.com] I would expect 75 concurrent connections spread across the 10 A records I've set in DNS. However I'm seeing more than a few hundred connections to mymta.com and I'm wondering if Postfix is "smart" enough to set up 75 concurrent connections for each IP address. Thoughts?

    Read the article

  • iOrgSoft Video Converter for Mac

    - by terryhao
    [url=http://www.iorgsoft.com/Video-Converter-for-Mac/]video converter for mac[/url] IOrgSoft[url=http://www.iorgsoft.com/Video-Converter-for-Mac/]video converter for mac[/url] is an excellent video converting and editing software for Macintosh users. A built-in powerful video player, trimming, splitter/joiner/merger tools give you everything you need to manage your videos on mac. This mac converter supports many video formats like AVI, MP4, WMV, MPEG-1,2, YouTube(FLV), Limewire, Realplayer(RM,RMVB), Quicktime(MOV), MKV, MOD, TOD, ASF, 3GP, 3G2, AVCHD/M2TS/MTS/TS/TRP/TS, MXF, etc. Video Converter for Mac features a very clean user interface which makes this task a breeze. You can trim/clip any segments and optionally merge/join and sort them to create your personal movie, crop frame size to remove any unwanted area in the frame just like a pair of smart scissors and set the output video parameters such as video resolution, video frame rate, audio codec, video codec and video quality. Converted videos can be imported into imovie/itunes/FCE/FCP/QuickTime Pro or played on iPad, iPod touch, iPod classic, iPod nano, iPhone, iPhone 3GS, Apple TV, PSP, PS3, Creative Zen, iRiver PMP, Archos, mobile phones and other MP4/MP3 players. Video Converter for Mac makes video conversion easy. Free download now and have a try for yourself! [url=http://www.iorgsoft.com/Video-Editor-for-Mac/]Video Editor for Mac[/url] [url=http://www.iorgsoft.com/Mod-Converter/]mod converter[/url] [url=http://www.iorgsoft.com/Mod-Converter-for-Mac/]mod converter for mac[/url]

    Read the article

  • How to find out which program a default beep is coming from in Windows 7?

    - by leeand00
    There's a "default beep" (as defined in System Sounds) that emanates from my computer every so often. It kind of goes like this (where each number is a "default beep" sound): 1, 2, 3, 4, 5. So there's a distinct pattern to it. I thought I had this figured out a way to figure out what was happening by going to Control Panel-Ease of Access-Ease of Access Center-Replace sounds with visual cues But that just isn't the case. Whichever window I click on, that one displays the visual queue when this happens. It's driving me crazy, and I can't figure out which program is causing this. Update: it appears to only happen on one user profile on the computer...does that help? Update 2: Discovered that this sound was coming from a utility on my laptop called ASUS NB Probe; I'm certain that it is emanating from this program because the error message displayed by it changes in sync with the sound playing. Apparently the S.M.A.R.T. feature of my hard drive was reporting an issue. It displays the issue for a brief second and then makes it disappear, I'll have to keep watching it to see what it says, but I believe is says something about a read. I have an external hdd connected with eSATA to a container of sorts (BlacX) that you can plug two hdds into. I have one hdd attached and it's a Western Digital WD1001FALS - 00E8B0 Thanks again! Now I'm off to go around the Internet and report on this...since I posted it so many places!

    Read the article

  • Trying to use a SmartHost with my Exchange 2010 server

    - by Pure.Krome
    Hi folks, I'm trying to use a SmartHost with my Exchange 2010 Server. SmartHost details: Secure SMTPS: securemail.internode.on.net 465 <-- Note: that's port 465 Configure your existing SMTP settings (in your email program) to: use authentication (enter your Internode username and password, enter your username as [email protected]). enable SSL for sending email (SMTPS). So I've added the smart host details to my Org Config -> Hub Transport. I then used PowerShell to add the port:- Set-SendConnector "securemail.internode.on.net" -port 465 I've then added my username/password (as suggested above) to the SmartHost as Basic Authentication (with no TLS). Then I try sending an email and I get the following error message :- 451 4.4.0 Primary target IP address responded with: "421 4.4.2 Connection dropped due to ConnectionReset." So i'm not sure how to continue. I also tried ticking the TLS box but stll I get the same error. If i don't use SMTPS (secure SMTP, on port 465) and use basic SMTP on port 25 with no Authentication, email gets sent. Any ideas? EDIT: Btw, I can telnet to that server on port 465 from my mail server .. just to make sure i'm not getting firewall'd, etc.

    Read the article

  • OS X Hard drive recovery

    - by Adam
    I am trying to recover data from a bad Seagate 1TB hard drive in a 2010 iMac. One day the iMac wouldn't boot (stuck at gray screen on startup). I removed the hard drive from the iMac and connected it to a MacBook using a 3.5" HDD to USB adapter. The hard drive wouldn't mount but it did display in Disk Utility that that there were 2 partitions on the disk. I tried to run Disk Warrior and it showed thousands of errors but still wouldn't mount. At this time the hard drive only show one partition in Disk Utility. Next I tried putting the hard drive in a desktop PC and running Spin Rite - which then gave me several division overflow errors (even with running Spin Rite with a newer version of DOS). The SMART status on the drive reports that the drive has had failures and HD Tune referenced the drive had once hit 59 degrees celsius. Disk Utility gives me the following message when running a pair: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files. Overall, the hard drive spins up and sounds OK - there are no clicking noises but the hard drive won't mount and displays as a light gray "Macintosh HD" in disk utility. Any tips or advice on how to recover data on this drive would be GREATLY appreciated! Are there any other tools I can try before calling it quits on this drive? Thank you

    Read the article

  • PGB Multipath & return routes

    - by Dennis van der Stelt
    I'm probably a complete n00b concerning serverfault related questions, but our IT department makes a bold statement I wish to verify. I've searched the internet, but can find nothing related to my question, so I come here. We have Threat Management Gateway 2010 and we used to just route the request to IIS and it contained the ip address so we could see where it was coming from. But now they turned on "Requests apear to come the TMG server" so ip addresses aren't forwarded anymore. Every request has the ip of the TMG server. Now the idea behind this is that because of multipath bgp routes, the incoming request goes over RouteA, but the acknowledgement messages could return over RouteB. The claim is that because the request doesn't come from the first known source, our proxy, but instead from IIS, some smart routers at the visitor of our websites don't recognize the acknowledgement message and filter it out. In other words, the response never arrives. Again, this is the claim. But I cannot find ANY resources on the internet that support this claim. I do read about pgb multipath, but more in the case that there are alternative routes when the fastest route fails for some reason. So is the claim completely bogus or is there (some) truth to it? Can someone explain or point me to resources? Thanks in advance!

    Read the article

  • Using a Linksys Wireless- G Broadband Router for a Wireless Antenna/Adapter?

    - by Alex
    (Warning: I'm not too computer-smart). Just moved fm a home where I used ATT DSL to a home w/ Comcast Cable for internet. Old home had the DSL ethernet wired to my only desktop w/ a 2Wire router for my wireless signal for the laptops. In the new home the signal comes fm cable via a Netgear(300) wireless router (remotely located) & works fine for my laptops. After searching with the network software, my desktop (can't be ethernet wired cuz of location) detects no wireless signal. Desktop is a 2 yr old HP p6311f Pavilion (Windows 7). Can't seem to detect any wireless hardware (ant/adaptr). Maybe I don't have the ability & need to buy a USB wireless antenna? Would the Pavilion come w/ wireless capability out of the box, maybe something inside the tower? No antenna on back. I happen to have a Linksys Wireless router which I plugged in to the desktop (trying both internet & shared ports) & noticed signal action on the router front panel. No internet on desktop though. Can I use this as an antenna for the desktop? Thanks & sorry if my solution is an easy one I'm just missing. Just want internet on the desktop.

    Read the article

  • How have multiple web servers and IPs on the same physical network

    - by jsigned
    I do web development out of a small office and need to have multiple physical and virtual servers that can be accessed from the internet. I also have a number of devices (computers, laptops, tablets, printers, etc) that need connections as well. I have gotten a subnet of 8 IP's from my ISP and while that is adequate for the web servers its far too small for everything that needs access to the network. My router is an ASUS RT-N16 running DD-WRT. I'm just smart enough about this routing topic to be dangerous, think 2 year old with a magic marker. I would like to keep my internal network NAT'ed on the 192.168.x.x network and route the 68.69.x.x 255.255.255.248 traffic directly to the servers. The physical network consists of the 4 port DD-WRT router and an unmanaged gig switch. I have a fiber connection to the office that works as an Ethernet port. In other words I can plug my laptop directly into it and have access to the internet. There is no login or password and the router is setup to get DHCP from the ISP, and to provide DHCP addresses for the internal network. What I've done so far is google and try different configurations with little success. In the end I decided I didn't even know how to ask the questions needed. My questions are: Is this the best way to configure the network? How do you do it? VLANs? Multiple routers? I've never had to configure a router using anything more than the GUI so if this is command line stuff be gentle.

    Read the article

  • Sorting/grouping when there are multiple values in one cell

    - by ngm
    I have an Excel 2007 spreadsheet, where each row of the dataset describes a feature of a piece of software. One of the columns in the spreadsheet is Relevant Users, which describes which users of the software the feature is of interest to. There may be a couple of different users interested in a feature, in which case I've been filling in the cell with the two user types separated by a colon, e.g. 'Usertype A; Usertype D'. Occassionally, I'd like to sort my data by the Relevant Users column. However, the way I'm populating the column means the sorting isn't very smart. If I have a feature where 'Relevant Users' is 'Usertype A; Usertype D', and then I sort by Relevant Users, that feature will be grouped at the end of all the other features of relevant to Usertype A, as it's just sorting alphabetically. But I want it to be listed in the two separate groups of Usertype A and Usertype D. Or, if I have a pivot table that groups the features together under the heading of Relevant User, I'll get all the features for 'Usertype A', then 'Usertype B', then 'Usertype C', then 'Usertype D', then 'Usertype A; Usertype D', etc. Whereas I really want a feature with Relevant Users as 'Usertype A; Usertype D' to show up in both the Usertype A group and the Usertype D group. I guess if this information was in a database I might have a many-to-many table linking Relevant Users to features. But is there a way to go about having this kind of many-to-many relationship in Excel?

    Read the article

  • Git push over http (using git-http-backend) and Apache is not working

    - by Ole_Brun
    I have desperately been trying to get push for git working through the "smart-http" mode using git-http-backend. However after many hours of testing and troubleshooting, I am still left with error: Cannot access URL http://localhost/git/hello.git/, return code 22 fatal: git-http-push failed` I am using latest versions of Ubuntu (12.04), Apache2 (2.2.22) and Git (1.7.9.5) and have followed different tutorials found on the Internet, like this one http://www.parallelsymmetry.com/howto/git.jsp. My VHost file currently looks like this: <VirtualHost *:80> SetEnv GIT_PROJECT_ROOT /var/www/git SetEnv GIT_HTTP_EXPORT_ALL SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER DocumentRoot /var/www/git ScriptAliasMatch \ "(?x)^/(.*?)\.git/(HEAD | \ info/refs | \ objects/info/[^/]+ | \ git-(upload|receive)-pack)$" \ /usr/lib/git-core/git-http-backend/$1/$2 <Directory /var/www/git> Options +ExecCGI +SymLinksIfOwnerMatch -MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> I have changed the ownership of the /var/www/git folder to root.www-data and for my test repositories I have enabled anonymous push by doing git config http.receivepack true. I have also tried with authenticated users but with the same outcome. The repositories were created using: sudo git init --bare --shared [repo-name] While looking at the apache2 access.log, it appears to me that WebDAV is trying to be used, and that git-http-backend is never fired: 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "GET /git/hello.git/info/refs?service=git-receive-pack HTTP/1.1" 200 207 "-" "git/1.7.9.5" 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "GET /git/hello.git/HEAD HTTP/1.1" 200 232 "-" "git/1.7.9.5" 127.0.0.1 - - [20/May/2012:23:04:53 +0200] "PROPFIND /git/hello.git/ HTTP/1.1" 405 563 "-" "git/1.7.9.5" What am I doing wrong? Is it an issue with the version of git and/or apache that I am using perhaps? BTW: I have read all the git http related questions on ServerFault and StackOverflow, and none of them provided me with a solution, so please don't mark this as duplicate.

    Read the article

  • Toshiba External Hard Drive freezes computer

    - by Ephraim
    I bought a Toshiba Canvio Basics E05A032BAU2XK Portable External 320GB 2.5 Hard Drive: My computer has two Os's on it Win7 and Win XP. I need both. The main one I use is XP. When booting my computer in any OS the computer and hard drive work fine. The same holds true for plugging in the hard drive while running Win7. However, when running WinXP, if the hard drive gets plugged in the computer freezes(my main point is that the HD is portable so it is essential that it does not do this, as I said I usually run XP). After reading some online forums I was informed that there is a compatibility issue with the newest version of Eset Smart Security(I still don't understand this because it works fine in Win7 or when connected on boot...). I disabled the AV and plugged in the HD... Walla! The comnputer did not freeze. However the disk is not recognized in explorer or disk management. In device manager I removed the device and did a scan and installation of device failed. It pretty much sounds like a driver issue but I cannot find any drivers for this HD. In fact, Toshiba claims that there are no downloadable drivers for it and that XP should take care of the drivers itself. What to do? As far as I can tell, all other USB devices work just fine on both OS. Please Help!

    Read the article

  • another "SSH connect to host github.com port 22: Bad file number"

    - by Mariusz
    Hello. I have a problem with my first-time ssh connection. Yes, I've already done yours guides, already tried your "Dealing with firewalls and proxies" article and the problem is still occuring. I am using Win7 32bit, Windows Firewall is disabled, haven't any third-party firewalls, ESET Nod32 Antivirus is not blocking any ports, I am not using any PROXY (neither local proxy) . Here goes the logs: Ordinary SSH connection try C:\Users\Mariusz>ssh -vvv [email protected] OpenSSH_4.6p1, OpenSSL 0.9.8e 23 Feb 2007 debug2: ssh_connect: needpriv 0 debug1: Connecting to github.com [207.97.227.239] port 22. debug1: connect to address 207.97.227.239 port 22: Not owner ssh: connect to host github.com port 22: Bad file number NCAT connection try C:\Users\Mariusz>ncat github.com 22 Strange connect error from 207.97.227.239 (10013): No error 10013 = WSAEACCES I think that method called "smart-http-support" won't be usable for me because I haven't created repo yet. I have just GIT INIT locally, and finished at step GIT PUSH, which returns the same: ssh: connect to host github.com port 22: Bad file number fatal: The remote end hung up unexpectedly corkscrew method (first article from yours guide) . While PUTTYing (with pageant in bg), after inputing login - an error is occuring (MessageBox): Disconnected: No supported authentication methods available And in terminal such message is printing out: Server refused our key Key I have generated correctly, using ssh-keygen. I tried not method by editing ~/.ssh/config yet because I had thought that because I haven't PUSHed anything to my remote repo so I won't be able to CLONE anything. Method called ssh-forwarding is not for my, cause it "requires access to an external ssh server" and I haven't any at this time. What else could I do? Thanks in advance for any help. Mariusz.

    Read the article

  • Routing for Two Hosts Behind a IPSec Tunnel

    - by Brent
    Network A 10.110.15.0/24 Firewall is .1 Host A is .2 Network B 10.110.16.0/24 Firewall is .1 Host B is .2 Two Cisco ASA's. IPSec tunnel with a crypo map that secures 10.110.15.0/24 <- 10.110.16.0/24. Let's say two hosts, 10.110.15.2 and 10.110.16.2 need to talk to each other. Normally I have to enter a persistent static route on a each host along the lines of: route add 10.110.16.0 mask 255.255.255.0 10.110.15.1 metric 1 -p (on the "A" box) I also have to enter another persistent static route on the .16 host in order for the traffic to know how to get back to the .15 network. Note that the default for each machine IS the firewall, so .1. I have no problem adding persistent routes on Windows/ESX/*nux machines but what about a smart switch in the .16 network that I want to manage from the .15 network. Do I need to run a routing protocol? Do I need to have Reverse Route Injection enabled on both ends of the IPSec tunnel? Should I add a route on the firewall? If so, how do you formulate it? Does it get a metric of 1 and my default route 0.0.0.0 get a metric of 2?

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • Getting 502 instead of 503 when all backend servers are down running HAProxy behind Apache

    - by scarba05
    I'm testing running HAProxy as a dedicated load balancer behind Apache 2.2, replacing our current configuration where we use Apache's load balancer. In our current, Apache only, set-up if all the backend (origin) servers are down Apache will serve a 503 service unavailable message. With HAProxy I get a 502 bad gateway response. I'm using a simple reverse proxy rewrite rule in Apache RewriteRule ^/(.*) http://127.0.0.1:8000/$1 [last,proxy] In HAProxy I have the following (running in default tcp mode) defaults log global option tcp-smart-accept timeout connect 7s timeout client 60s timeout queue 120s timeout server 60s listen my_server 127.0.0.1:8000 balance leastconn server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 Testing connecting directly to the load balancer when the backend servers are down: [root@dev ~]# wget http://127.0.0.1:8000/ test.html --2012-05-28 11:45:28-- http://127.0.0.1:8000/ Connecting to 127.0.0.1:8000... connected. HTTP request sent, awaiting response... No data received. So presumably this is down to the fact that HAProxy accepts the connection and then closes it.

    Read the article

  • Are there cloud network drives that let users lock files or mark them as "in use"?

    - by Brandon Craig Rhodes
    Having spent several hours reading about the features and limitations of services like DropBox and Jungle Disk and the hundreds of competitors they seem to have (as though everyone with an AWS account these days goes ahead and writes a file sharing application just for fun), I have yet to find one that would let a team of people at a small business collaborate without stepping all over each other's toes. At a small business there are often many small documents per project — estimates, contracts, project plans, budgets — and team members frequently have to open and edit them, with all sorts of problems happening if two people edit a file at once. Even if a sharing service is smart enough to keep both versions of the file created, most small-business software (like word processors, spreadsheets, estimating software, or billing systems) has no way to compare — much less to merge! — the changes in two rival versions of a file that two people edited at the same time without each other's knowledge. So, my question: are their cloud-based file sharing solutions that not only provide a virtual network drive that people can access, but that also let users lock files — even if it's not a real lock but just a flag or indicator — that could possibly prevent remote workers from both editing the same file at once? Having one person wait for another person to finish editing is a very, very small inconvenience compared to the hour or more than it can take to compare two estimates by hand until you find and resolve the rival changes. Given this fact, I am surprised that almost none of the popular file sharing solutions seem to recognize this problem and provide some solution! Does anyone know of a service that does?

    Read the article

  • Formatting an external HDD stuck at 70%

    - by mahmood
    My external HDD which is a 250GB WD (powered by USB) seems to have problem! Whenever i try to copy some files, it stuck while copying. I decided to format it. So I used windows tool and performed the format (not quickly) however at nearly 70% it stuck. Then I decided to perform a low level format with lowlevel. Again it stuck at 70%. I endup that the HDD has bad sector. So is there any tool that mark the bad sectors and bypass them? It is not very reasonable to through 250GB because of some bad sectors! P.S: I saw a similar topic but there were no conclusion there either. The smart data is Attribute, raw value, value, threshold, status Read Error Rate, 50, 200, 51, OK Spin-Up Time, 3275, 154, 21, OK Start/Stop Count, 2729, 98, 0, OK Reallocated Sectors Count,0, 200, 140, OK Seek Error Rate, 0, 100, 51, OK Power-On Hours (POH), 1057, 99, 0, OK Spin Retry Count, 0, 100, 51, OK Recalibration Retries ,0, 100, 51 , OK Power Cycle Count, 1385, 99, 0, OK Power-off Retract Count, 425, 200, 0, OK Load /Unload Cycle Count,12974, 196, 0, OK Temperature, 43, 43, 0, OK Reallocation Event Count,0, 200, 0, OK Current Pending Sector Count,23,200, 0, Degradation Uncorrectable Sector Count, 0, 100, 0, OK UltraDMA CRC Error Count,6, 200, 0, OK Write Error Rate/Multi-Zone Error Rate,0,100,51, OK It seems that the most important thing is this line Current Pending Sector Count,23,200, 0, Degradation Any idea on that?

    Read the article

< Previous Page | 64 65 66 67 68 69 70 71 72 73 74 75  | Next Page >