Search Results

Search found 22298 results on 892 pages for 'default'.

Page 686/892 | < Previous Page | 682 683 684 685 686 687 688 689 690 691 692 693  | Next Page >

• Chrome Lockups Windows 7 64-bit

  - by Mike Chess

  I'm running Google Chrome (6.0.427.0 dev) on Windows 7 Home Premium 64-bit (AMD Phenom 3.00 GHz, 8 GB RAM). The computer lockups hard after running Chrome for about five minutes. The lockup happens whether Chrome is actually being used to browse web sites or it is just idling. No programs can be started or interacted with when this happens. The computer must be power-cycled to recover. The lockup happens regardless of which web sites are being browsed. The system event logs do not show any events around the time when the lockup transpired. All other applications run just fine on this system. In fact, Chrome ran without issue for several months on this system (the system was brand new 03-2010). I also run the same version of Chrome on other computers (Windows XP SP3) without issue. I've come to really like Chrome and use it as my default browser whenever possible. What could be causing Chrome to cause the system to lockup as it does? Does Chrome have any logs that aren't part of the Windows event log? Does Chrome have a debug command line switch that might reveal more about what happens?

  Read the article

• Recommendation for a simple no-frills Windows PDF printer driver?

  - by Scott Bussinger

  I'm looking for an extremely simple Windows PDF printer driver that I can recommend to clients. Ideally it would have these characteristics: When you print something, it should just create it as a temporary file and then display it in their default PDF viewer with no prompting. If they want to save it, they can save it manually from inside the viewer. This workflow should be with no special post-install configuration. Installation should be very simple. A double click the installation program and click "Finish" sort of thing. No complicated multi-step installation, no asking questions your grandmother wouldn't know the answer to (preferably no questions at all), no extra crap being installed. An option for a completely silent installation would be nice, but not necessary. Ideally it would be free to simplify their installing on a small network, but low cost is an option. I've tried a quite a few but none really fit the bill. Some can achieve the first goal but only after careful configuration, some try to install extra toolbars, some have other installation complexities that would make it hard for extremely novice users to succeed. Any suggestions? Thanks!

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Will a SQL Server client alias survive a sysprep?

  - by shufler

  I want to sysprep a Windows Server 2008 R2 SP1 machine that has SQL Server 2008 R2 SP1 installed (for reference, SQL Server 2008 R2 has a new sysprep feature that allows the instance to be sysprepped). On the server is a SQL Server client alias that points to the default SQL Server database engine instance. For reference, the alias is called Alias-SQLServer and has been configured in both 32-bit and 64-bit cliconfig versions (that is, both registry keys exist) The alias points to the local instance as the image will be used to create development VMs and the installation script for the application that is being developed will use the SQL Server client alias in order to generalize the installation scripts. I can't seem to find information about whether the sysprep tool will update the SQL Server client alias's registry keys with the server's new name once it's unsealed. My guess is that it is not; how is sysprep to know that the server name the alias points to will be different for each image? Right? Perhaps if the alias points to localhost instead of the server name this will work?

  Read the article

• One Windows Domain workstation can ping gateway but gets no internet access

  - by dindeman

  One of the (Windows XP SP3) workstations of our Windows Domain could not access internet anymore, this problem suddenly happened overnight. The domain controllers (there are three of them) are all running Windows Server 2008. First I compared the output of ipconfig /all on the faulty workstation with the output of a working workstation and it was just fine as it had always been. In particular the default gateway was correct and always remained pingable from the faulty workstation. I guessed that something was wrong with the DHCP service and I restarted the DHCP server service on all of our three DCs as well as the DHCP client service on the faulty workstation. This didn't solve the issue. I then thought of renewing the DHCP lease with ipconfig /release and ipconfig /renew and here is my first question: why did this never work? The same IP address (192.168.0.45) kept being assigned despite all my attempts to renew it (note that all our workstation are getting their TCP/IP automatically.) Even by leaving the domain and changing the computer name the same address was yet again obtained... Anyway I then proceeded to switch the TCP/IP configuration for that machine manually to another free valid IP address (192.168.0.41)... and then the internet access came back! I then cleared any traces of the previous IP in the DHCP leases list and in the DNS tables of our DCs and, after setting back the TCP/IP configuration to 'automatic', finally, the new lease would be granted (192.168.0.41) alongside with the internet access. My second question: what went suddenly wrong with the original IP address?

  Read the article

• credit or minclass does not work well with pam_cracklib.so in common-password (opeSuSe 11.3)

  - by Mario

  I'm trying to implement password complexities on my pdc. It's a samba PDC with openLDAP backend. I tried cracklib-check but it looks like that I should have a decent and localize version of password library since the library out there usually comes in english. I also have another consideration that we will allow users to use any kind of password - even though it's dictionary based - as long as their passwords integrated with low/upper alphabet, digits, and other characters such as '$' or '_' (pam_cracklib.so calls them as classes). So here is my /etc/pam.d/common-password: #password requisite pam_pwcheck.so nullok cracklib password requisite pam_cracklib.so minclass=4 reject_username ##password requisite pam_cracklib.so \ ## dcredit=-1 ucredit=-1 lcredit=-1 ocredit=-1 reject_username password optional pam_gnome_keyring.so use_autht_ok password required pam_unix2.so use_authtok nullok The first commented line (with #) was the default configuration of openSuse 11.3. The 2nd/3rd (with leading ##) is another configuration I use when minclass=4 line is commented out. By the way, I have 'check password script' = /usr/local/sbin/crackcheck -d /usr/share/cracklib/pw_dict and passdb backend = ldapsam:ldap://127.0.0.1 parameters in smb.conf and cracklib-check works fine too. So here is the test I conduct. I logon to windows and then change my password. Sometimes it works fine that it trows error message - which what I wanted, but simple password with only lower alphabets can pass windows change password. Maybe I should make a new library which incorporates local vocabularies, but a guy out there (raise your hand please if you read this :) ) also experienced the same trouble with english word. Besides, what we really want is to let user to choose 2 or 3 format password out of 4 classes. Is there a bug or something with pam module in openSuse 11.3? Thank you in advance. Regards, Mario

  Read the article

• Windows 7 Taskbar resets on every login

  - by Arne Mertz

  I like to reorder my Taskbar a bit, other than the Windows 7 default is. I use two "rows", the lower is for quicklaunch and other toolbars: This works perfectly, as long as I don't log off from the computer. Every time I log in, Windows 7 has messed up/reset the toolbar positions like this: So I have to drag them into position again and again, every morning. Fixing the taskbar positions won't help, I tried to google for the problem but it does not seem to be very common. Does anyone recognize that problem and has a solution? Update: This is not the AutoLogon bug. AutoLogon is off. We have installed Novell at our company, and it does not matter wether I log directly onto the Novell network or only to the computer first and to Novell later. Update2: I get the same issue when I logon without Novell, i.e. when I log on only to the computer. When I boot in safe mode, the taskbar looks essentially the same: Update3: KB979155 says it's "not applicable to my system". Creating a neew user is not an option since I don't have the admin privileges to do that - I have almost any other local admin privileges, though.

  Read the article

• Can't Connect SQL server - process being used by another process. Conflict with IIS?

  - by shinya

  I'm having problem connecting to MS SQL Server (2012 Express) after accessing a database through IIS (web site). I can access the data through web site no problem, but I can't access the data from any other programs (i.e SSMS) until I reboot the SQL server. It seems that the connection stays open even if I close a browser. Here is error message I'm getting Unable to open the physical file "C:---------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Unable to open the physical file "C:-------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Cannot open user default database. Login failed. Login failed for user 'Myserver\myname'. (.Net SqlClient Data Provider) Server Name: MYPC\SQLEXPRESS Error Number: 5120 Severity: 16 State: 101 Line Number: 65536 I follow the help link and it told me to move TCP before named pipes in the protocol order list. I tried it but it didn't help at all. What is the proper settings on SQL server or IIS in order to release process after closing a browser. How do I avoid getting this error? Thank you for your help

  Read the article

• Create custom launchers in GNOME 3

  - by hochl

  I'm using Debian testing, and I have been switched to GNOME 3 by the Debian update yesterday. I'm not very comfortable with the UI. I wanted to customize everything like I had it with GNOME 2, but I simply couldn't find any way to change preferences like I'm used to. I've digged some, but all answers I could find did not help me achieve my goals. So please, if anyone knows the solution to this I'd be thankful: 1) I want several launchers that launch terminals, with different arguments and different coloring/title. I have searched everything and there seems to be no menu, no right-click, nothing which is standard in any UI I know. How can I create several launchers in this bar on the left side that launch the same application, just with different parameters? With GNOME 2 this was a piece of cake. 2) I want to switch between different terminals using ALT-TAB. Right now, I'm always just getting to the same, already-opened terminal. When I open two terminals by simply creating the second one by issuing xterm &, I still get one Terminal entry with ALT-TAB, and I have to navigate with cursor keys or mouse wheel to select one of the two xterminals. Instead, I want to open a new terminal when I click the quick launch terminal icon from the bar on the left side of the screen and navigate through them like on KDE/GNOME 2/Windows/any reasonable UI. Can this be done? 3) Is there a trick to make bluetooth devices work like on GNOME 2? Right now, my BT keyboard won't pair anymore, which, as you can imagine, makes me pretty angry. and, if anything fails: 4) How can I switch back to GNOME 2 again? :-) Honestly, who did design this? What were they smoking? I feel like I'm not allowed to do anything except start one of any application that has an icon and just with the default parameters. That can't be true, right? I feel massively restrained by this stuff :(

  Read the article

• Restoring a fresh home folder in a shared user domain environment

  - by Cocoabean

  I am using a tool called pGINA that adds another credential provider to my Windows 7 clients so we can authenticate campus users via campus LDAP. We have the default Windows credential providers setup to authenticate off of our Active Directory, but we have students in our classes that don't have entries in our AD, and we need to know who they are to allow them internet access. Once these LDAP users login using pGINA, they are all redirected to the same AD account, a 'kiosk' account with GPOs in place to prevent anything malicious. My concern is that my users will accidentally save personal login information or files in that shared profile, and another user may login later and have access to a previous user's Gmail account, as the AppData folder on each computer is shared by anyone logging into the kiosk user. I've looked into MS's 'roll-your-own' SteadyState but it didn't seem to have what I wanted. I tried to write a PS script to copy a pre-saved clean version of the profile from a network share, but I just kept running into issues with CredSSP delegation and accessing the share from the UNC path. Others have recommended something like DeepFreeze but I'd like to do it without 3rd party tools if possible.

  Read the article

• Multiple Routers, Failover, DHCP and multiple gateways. NOT WAN-failover

  - by u_b

  I've had a look around google and this forum but could not find an answer to my question. So probably one of you can help me a little. My intended setup is: Router R1: wan connection to isp. connected backup server. provides some wireless SSID. other connected devices like printer, laptop, etc. both wired and wireless. Router R2: no wan connection to isp but connected to R2. connects mp3-streamer and music server. also serves as a wireless access point with same SSID. other than described connections only wireless connections. I would like to be able to control music even if R1 is off, e.g. with no internet connection. On the other hand I would like to access internet also in the case that R2 is off, i.e. no music access. Last but not least I would like to stream internet radio, i.e., R1 and R2 are on, and music is streamed from internet to R1 to R2 to streamer. I would like to realize all this using DHCP (also using static assignments) so i do not have to configure statically on android, laptop, etc. So my questions are: Can I make DHCP provide a list of two default gateways R1,R2? In order to make clients fallback to other gateway if currently assigned gateway is turned off? Thanks in advance, u_b

  Read the article

• Heavy write to Galera cluster - table locked, cluster practically unusable

  - by Joe

  I set up Galera Cluster on 3 nodes. It works perfectly for reading data. I have done simple application to make some test on the cluster. Unfortunately I have to say that the Cluster fails totally when I try to do some writing. Maybe it can be configured differently or I do sth wrong? I have a simple stored procedure: CREATE PROCEDURE testproc(IN p_idWorker INTEGER) BEGIN DECLARE t_id INT DEFAULT -1; DECLARE t_counter INT ; UPDATE test SET idWorker = p_idWorker WHERE counter = 0 AND idWorker IS NULL limit 1; SELECT id FROM test WHERE idWorker = p_idWorker LIMIT 1 INTO t_id; SELECT ABS(MAX(counter)/MIN(counter)) FROM TEST INTO t_counter; SELECT COUNT(*) FROM test WHERE counter = 0 INTO t_counter; IF t_id >= 0 THEN UPDATE test SET counter = counter + 1 WHERE id = t_id; UPDATE test SET idWorker = NULL WHERE id = t_id; SELECT t_counter AS res; ELSE SELECT 'end' AS res; END IF; END $$ Now my simple C# application creates for example 3 MySQL clients in separate threads and each one executes the procedure every 100ms until there is no record where column 'counter' = 0. Unfortunately - after about 10 seconds sth is going bad. On servers there is process 'query_end' that never ends. After that - you cannot make update on the test table, MySQL returns: ERROR 1205 (HY000): Lock wait timeout exceeded; try restarting transaction . You cant even restart mysql. What you can do is to restart server, sometimes whole cluster. Is Galera Cluster so unreliable when you do massive concucurrent writing/updates? Hard to believe.

  Read the article

• How to make Firefox file associations consistent with Ubuntu file associations?

  - by wbharding

  This seems to be a pretty commonly Google question, but one for which there are no answers. http://www.linuxquestions.org/questions/linux-software-2/firefox-download-mime-types-378902 http://www.birkit.com/content/kubuntu-linux/internet/firefox/fix-file-associations-in-firefox.html Being three links amongst the many. The gist of what I want to accomplish is to have Firefox understand the file associations I download without me having to manually map all of them myself. Gnome knows the file extensions, so I would have expected that Firefox could just use the already-known file mappings there to open the right stuff (as I presume Chrome does). But it doesn't. At least not for me, using Firefox 4, and not by default. When I click on a downloaded file right now, Firefox always has to ask me what application should be used to open the file. A handful of Google results tell me that I can reassociate my file extensions by deleting ~/.mozilla/firefox/[profile name]/mimeTypes.rdf, but while deleting that file does in fact result in a new mimeTypes file being generated, the new mimeTypes is just as barren as the old one had been. Based on the amount of unanswered Qs on the Googlesphere, I know this is a very common problem for Ubuntu users, but it seems to be one for which nobody has chimed in with a good solution. Maybe Superuser can finally be the panacea for us all?

  Read the article

• Libvirt/KVM in NAT: can't access from host (and can't forward)

  - by SharkWipf

  I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

  Read the article

• Need help trying to allow my remote PowerShell script to run on my Windows 2008 r2 Server

  - by Pure.Krome

  I've got a Windows 2008 r2 server with Sql Server 2008 r2 installed. I've got a Sql Server Agent which tries to run a Powershell job, but fails :- Message Executed as user: FooServer\SqlServerUser. A job step received an error at line 1 in a PowerShell script. The corresponding line is '& '\\polanski\Backups\Database\7ZipFooDatabases.ps1'' Correct the script and reschedule the job. The error information returned by PowerShell is: 'File \\polanski\Backups\Database\7ZipFooDatabases.ps1 cannot be loaded. The file \\polanski\Backups\Database\7ZipFooDatabases.ps1 is not digitally signed. The script will not execute on the system. Please see "get-help about_signing" for more details.. '. Process Exit Code -1. The step failed. Ok. So i run Powershell on that server then set the execution policy to unrestricted. To check .. PS C:\Users\theUser> Get-ExecutionPolicy Unrestricted PS C:\Users\theUser> Kewl :) but it still doesn't work :( Ok ... what happens when i try to run the powershell from the command line.... PS C:\Users\justin.adler . '\polanski\Backups\Database\7ZipMotorshoutDatabases.ps1' Security Warning Run only scripts that you trust. While scripts from the Internet can be useful, this script can potentially harm your computer. Do you want to run \\polanski\Backups\Database\7ZipFooDatabases.ps1? [D] Do not run [R] Run once [S] Suspend [?] Help (default is "D"): er..... didn't I already tell the server that ANY file can be ran? Notice the file is located at... \\polanski\Backups\Database\ So can someone make any suggestions?

  Read the article

• How do I add a second disk to my zfs root pool

  - by ankimal

  I am trying to add a new disk to my zfs root pool. Here is my current config: zpool status pool: rpool state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM rpool ONLINE 0 0 0 c0d0s0 ONLINE 0 0 0 errors: No known data errors bash-3.00# df -h Filesystem Size Used Avail Use% Mounted on rpool/ROOT/s10x_u7wos_08 311G 18G 293G 6% / swap 14G 384K 14G 1% /etc/svc/volatile /usr/lib/libc/libc_hwcap1.so.1 311G 18G 293G 6% /lib/libc.so.1 swap 14G 52K 14G 1% /tmp swap 14G 40K 14G 1% /var/run rpool/export 293G 19K 293G 1% /export rpool/export/home 430G 138G 293G 32% /export/home rpool 293G 36K 293G 1% /rpool # format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c0d0 <DEFAULT cyl 60797 alt 2 hd 255 sec 63> /pci@0,0/pci-ide@1f,2/ide@0/cmdk@0,0 1. c2d0 <Hitachi- JK1181YAHL0YK-0001-16777216.> /pci@0,0/pci-ide@1f,5/ide@1/cmdk@0,0 Disk 1 above is the new disk I need to attach to expand my root pool (give /export/home some extra space). If I try to attach my new disk to the pool # zpool attach -f rpool c0d0s0 c2d0s0 cannot attach c2d0s0 to c0d0s0: new device must be a single disk # uname -a SunOS dsol1 5.10 Generic_139556-08 i86pc i386 i86pc Solaris Any ideas?

  Read the article

• Cannot install windows. Compaq Presario CQ62

  - by Matthew

  I bought a used Compaq Presario CQ62 for cheap, and went to install windows on it. I formatted the partition and went to install when I got this error.... Windows cannot install required files. The file may be corrupt or missing. Make sure all files required for installation are available and restart the installation. Error code: 0x80070017 I have used this disk before with no problems, but internet searching suggested I burn one at 2x speed because that helps for some reason... I'm burning one now, but my question is, why would I get this error, OTHER than the disc being bad? I'm pretty certain this one isn't as I have used it before... (ok so the slowly burned cd (using imgburn) didn't work either so it's DEFINITELY not the disc) Thanks in advanced for any answers Also I took one stick of ram out because internet searching also suggested that, but it didn't make a difference. Also I ran memory and hard drive checks and they passed fine. Also I reset the motherboard options to default What could it be!? Help I'm completely stumped...

  Read the article

• How to write rules for persistent net names?

  - by ndemou

  I know that a process generates persistent network card names based on rules found in /lib/udev/rules.d/75-persistent-net-generator.rules. I also know how to completely disable this process with a simple echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules but I've read that I "could also write my own rules file to give the interface a name — the persistent rules generator ignores the interface if a name has already been set" (/etc/udev/rules.d/README confirms that this is possible). Do you have any pointers to documentation about how to write such rules? (I mostly care about Debian/Ubuntu and a bit less for CentOS) As a specific example of why I want to write custom rules: I have two identical servers with one onboard LAN and one PCI LAN. In case of HW failure I want to be able to move disks from HW#1 to HW#2 and it's important for eth0 to continue pointing to the onboard card and eth1 to the PCI card (no one wants to mess with cabling in the middle of a HW failure panic). My current workaround works but is a lot of work[1] so I wonder if writing custom rules would allow me to express something simple like this: cards with MAC A or B should be named eth0 cards with MAC C or D should be named eth1 follow default naming scheme for anything else [1] install the OS in HW#1 and keep a copy of /etc/udev/rules.d/70-persistent-net.rules. Move the disks to HW#2 and keep a second copy of the same file. Concatenate the two copies and manually edit the NAME="ethX" part. Replace /etc/udev/rules.d/70-persistent-net.rules with my version. Finally disable auto-creation of a new 70-persistent-net.rules using echo '#' > /etc/udev/rules.d/75-persistent-net-generator.rules

  Read the article

• Can't ping localhost/or reach locally hosted domain

  - by Ian

  I can't reach a locally hosted domain, and in testing I have discovered I can't ping localhost or the actual IP either. OS is Windows7 64bit, Pro. DNS works, I can ping others on my network, they can ping me, and they can reach the hosted domain. The ONLY problem I have found is that I can't reach the locally hosted domains! C:\Users\ianipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : leda Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hcs Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hcs Description . . . . . . . . . . . : Atheros AR8121/AR8113/AR8114 PCI-E Ethern et Controller Physical Address. . . . . . . . . : 00-23-54-7C-E2-2A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.12(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VirtualBox Host-Only Network #2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VirtualBox Host-Only Ethernet Adapter #2 Physical Address. . . . . . . . . : 08-00-27-00-88-4A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Autoconfiguration IPv4 Address. . : 169.254.205.215(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Enabled C:\Users\ianping localhost Pinging leda [127.0.0.1] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 127.0.0.1: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\Users\ianping coachmaster.leda.hcs Pinging coachmaster.leda.hcs [192.168.0.12] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.12: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\Users\ian I can reach a hosted VM in VirtualBox and the VM can browse the hosted sites. I've removed Zone Alarm and disabled Windows Firewall - same results. So how can I browse my locally hosted sited? What could be blocking it? Thanks Ian

  Read the article

• SSH attcack CentOS Amazon EC2

  - by user37143

  Hi, I run a few Rightscale CentOS AMI based instances on Amazon EC2. Two months back I found that our SSHD security is compromised( I had added host.allow and host.deny for ssh). So I created new instances and done an IP based ssh that allows only our IPs through AWS Firewall(ec2-authorize) and chnaged the ssh 22 default port to some other port but two days back I found I was not able to login to the server and when I tried on 22 port the ssh got connected and I found that sshd_conf was changed and when I tried to edit sshd_config I found root had no write permission on the file. So I tried a chmod and it said access denied for 'root' user. This is very strange. I checked secure log and history and found nothing informative. I have PHP, Ruby On Rails, Java, Wordpress apps running on these server. This time I did a chkrootkit scan and found nothing. I renamed the /etc/ssh folder and reinstalled openssh through yum. I had faced this on 3 instances on CentOS(5.2, 5.4) I have instances on Debian as well those working fine. Is this a CentOS/Rightscale issue. Guys, what security measures I should take to prevent this. Please support me this is very critical. Thanks

  Read the article

• Why does my Windows 8 Pro Hyper-V guest have no internet?

  - by Perplexed

  Trying to get this working on my Windows 8 Pro machine. I created an External Switch Assigned the newly available adapter to a Guest machine with Win 2008 os. My host has internet connection. Host can ping Guest, Guest cannot ping Host. Guest has no internet connection. Pasting the IP of both host and guest. HOST ========================== Ethernet adapter vEthernet (EXTSW01): Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Hyper-V Virtual Ethernet Adapter #2 Physical Address. . . . . . . . . : 9C-B7-0F-0F-D7-D0 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::5434:a9fd:8611:d207%54(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.15(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Saturday, September 8, 2012 12:34:44 PM Lease Expires . . . . . . . . . . : Saturday, September 15, 2012 12:34:44 PM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DHCPv6 IAID . . . . . . . . . . . : 916240141 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DC-C9-2C-9C-B7-0D-0D-D7-D0 DNS Servers . . . . . . . . . . . : 64.71.255.999 NetBIOS over Tcpip. . . . . . . . : Enabled GUEST ========================== Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter Physical Address. . . . . . . . . : 00-15-5D-3F-0F-00 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::953f:ec5c:5d84:1b50%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.20(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 0.0.0.0 DHCPv6 IAID . . . . . . . . . . . : 234886493 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DD-2F-29-0F-15-5E-00-0F-00 DNS Servers . . . . . . . . . . . : ::1 127.0.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• OpenSSL force client to use specific protocol

  - by Ex Umbris

  When subversion attempts to connect to an https URL, the underlying protocol library (openssl) attempts to start the secure protocol negotiation at the most basic level, plain SSL. Unfortunately, I have to connect to a server that requires SSL3 or TLS1, and refuses to respond to SSL or SSL2. I’ve done some troubleshooting using s_client and confirmed that if I let s_client start with the default protocol the server never responds to the CLIENT HELLO: $ openssl s_client -connect server.domain.com:443 CONNECTED(00000003) write:errno=104 --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 320 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- Watching this in Wireshark I see: Client Server -------syn----------> <------ack----------- ---CLIENT HELLO-----> <------ack----------- [60 second pause] <------rst----------- If I tell s_client to use ssl2 the server immediately closes the connection. Only ssl3 and tls1 work. Is there any way to configure openssl to skip SSL and SSL2, and start the negotiation with TLS or SSL3? I've found the OpenSSL config file, but that seems to control only certificate generation.

  Read the article

• Use external display from boot on Samsung laptop

  - by OhMrBigshot

  I have a Samsung RV511 laptop, and recently my screen broke. I connected an external screen and it works fine, but only after Windows starts. I want to be able to use the external screen right from boot, in order to set the BIOS to boot from DVD, and to then install a different OS and also format the hard drive. Right now I can only use the screen when Windows loads. What I've tried: I've tried opening up the laptop and disconnecting the display to make it only find the external and use the VGA as default -- didn't work. I've tried using the Fn+key combo in BIOS to connect external display - nothing I've been looking around for ways to change boot sequence without entering BIOS, but it doesn't look like it's possible. Possible solutions? A way to change boot sequence without entering BIOS? Someone with the same brand/similar model to help me blindly keystroke the correct arrows/F5/F6 buttons while in BIOS mode to change boot sequence? A way to force the external display to work from boot, through modifying the internal connections (I have no problem taking the laptop apart if needed, please no soldering though), through BIOS or program? Also, if I change boot sequence without accessing external screen, would the Ubuntu 12.1 installation sequence attempt to use the external screen or would I only be able to use it after Linux is installed and running? I'd really appreciate help, I can't afford to fix the screen for a few months from now, and I'd really like to make my computer come back to decent performance! Thanks in advance!

  Read the article

• SSH not working through Double NAT

  - by d_inevitable

  I am trying to setup port forwarding for ssh through 2 NATs The first Router translates my internet IP to my outer network (10.1.7.0). In the outer network there's a second Router that does NAT to my inner network (192.168.1.0). The target server is connected to both, the outer network and the inner network. I cannot change the port forwarding options for outer router. It is currently configured to forward the SSH and HTTP port to the router for the inner network. Internet + | v +-----------------+ +------------------+ | Outer Router | | Inner Router | |-----------------| |------------------| | | SSH HTTP | | +----+ +--------------------->| | | | | | | | | | | | | +-------+---------+ +------+---------+-+ | | | | | | | | | | | | | | +------------------+ | SSH | | | | Server | | | | | |------------------| | | | +-----------> |<-------+ | | | | |HTTP (testing) | +------------------+ | | | +------v------------------+ | | Outer Workstation | +-------------------+ | |-------------------------| | Inner Workstation| | | | |-------------------| | | | | |<----------------+ +-------------------------+ | | +-------------------+ When connecting from a outer workstation to the address of the inner router, then both SSH and HTTP work fine. When connecting from the internet to my public ip with HTTP, the connection works fine as well. However SSH just times out. Most likely because the reply is not routed back properly. I suspect its either because of the SSH itself, or because the server is connected to both, the inner and outer network. Any ideas how I could resolve this issue? The routes on the server are currently: ip route show default via 10.1.7.254 dev eth0 metric 100 10.1.7.0/24 dev eth0 proto kernel scope link src 10.1.7.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.2 Do I have to change this? If so how?

  Read the article

• "Error 5: Access denied" when installing programs with UAC turned off

  - by Aero

  I'm having some trouble installing msysgit 1.7.3.1preview on Windows 7 Home Premium. I downloaded the setup file from the Google Code and then ran it. Upon running, I got the following error: I have tried downloading and running different older versions of msysgit with no luck. For the record, I have administrative privileges and there are no other user accounts on this Windows machine. Any help would be greatly appreciated. Thanks. UPDATE: I have managed to semi-fix this problem. I turned on User Account Control back to the default setting and and then ran the setup file as an administrator. I successfully managed to install Git. However, this means I have to keep UAC turned on whenever I want to install a new program (I realised that it persists over all programs; not just Git). So it's quite a nuisance. If anybody knows how I could keep UAC disabled whilst still being able to install programs without running their setup files as an administrator, I would be eternally grateful. UPDATE: I have changed the question title to better suit the new situation.

  Read the article

< Previous Page | 682 683 684 685 686 687 688 689 690 691 692 693  | Next Page >