Search Results

Search found 3522 results on 141 pages for 'ams 23'.

Page 69/141 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

  • How do I get 1366x768 resolution on 12.04?

    - by Megan
    I am on an HP Envy 14, and the proper resolution that I should be using is 1366x768. This is not an option and I am stuck on 1024x768. I am using Linux 12.04. lspci | grep VGA: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Madison [Radeon HD 5000M Series] I've tried to add the resolution as a mode in xorg.conf but that does not work. Please any help would be appreciated. I'm new to Linux and just got my dual boot working but this resolution issue is killing me. Edit1 I just tried using the xrandr command: xrandr --newmode "1368x768_60.00" 85.25 1368 1440 1576 1784 768 771 781 798 -hsync +vsync But I get an error: xrandr: Failed to get size of gamma for output default Edit2 lsmod returns the following: Module Size Used by vesafb 13844 1 rfcomm 47604 12 bnep 18281 2 parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 arc4 12529 2 joydev 17693 0 hid_logitech_dj 18594 0 i915 472941 5 uvcvideo 72627 0 usbhid 47199 1 hid_logitech_dj hid 99559 2 hid_logitech_dj,usbhid psmouse 87692 0 iwlwifi 332525 0 mac80211 506816 1 iwlwifi videodev 98259 1 uvcvideo snd_hda_codec_idt 70795 1 mei 41616 0 btusb 18288 2 v4l2_compat_ioctl32 17128 1 videodev hp_accel 25976 0 lis3lv02d 19876 1 hp_accel hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi input_polldev 13896 1 lis3lv02d drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 serio_raw 13211 0 snd_hda_intel 33773 5 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec bluetooth 180104 23 rfcomm,bnep,btusb cfg80211 205544 2 iwlwifi,mac80211 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec mac_hid 13253 0 snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_ra wmidi,snd_seq,snd_timer,snd_seq_device wmi 19256 1 hp_wmi video 19596 1 i915 intel_ips 18174 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 I have installed ATI/AMD proprietary FGLRX graphics driver. But there is another one called ATI/AMD proprietary FGLRX graphics driver (post-release updates) which I have trouble installing because it gives me an error and tells me to look at some sort of jockey log.

    Read the article

  • Low-res emacs24 icon in application switcher 12.10

    - by MTS
    I recently upgraded to Quantal, and also switched up to emacs24 from 23. Everything is great, except for one thing: the icon in the Application Switcher for emacs24 is a horrible, low-resolution eyesore. Compare the two side-by-side: I've seen a couple of questions addressing issues like this, but they're not quite the same. This one says that it is happening with all icons, but that's clearly not the case here. And this one seems more relevant, but it is talking about Gnome, not Unity. In the comments to the one answer for the second question, it says to look at the icons in /usr/share/icons to see if they are low-resolution, and if so to replace them with better ones. There's a ton of emacs icons, in fact. They are in various subfolders of /usr/share/icons/hicolor and they are in sizes ranging from 16x16 to 128x128, and also there are scaleable .svg versions of the icons too. I noticed that there are no 192x192 or 256x256 versions. But it seems like that shouldn't matter, since emacs23 also didn't have icons in those sizes. Any help would be much appreciated!

    Read the article

  • CCSpriteHole in cocos2d 2.0?

    - by rakkarage
    i was using this cocos2d class CCSpriteHole in cocos2d 1.0 fine... http://jpsarda.tumblr.com/post/15779708304/new-cocos2d-iphone-extensions-a-progress-bar-and-a i am trying to convert it to cocos2d 2.0... i got it to compile by changing glVertexPointer to glVertexAttribPointer like in the 2.0 version of CCSpriteScale9 here http://jpsarda.tumblr.com/post/9162433577/scale9grid-for-cocos2d and changing contentSizeInPixels_ to contentSize_... -(id) init { if( (self=[super init]) ) { opacityModifyRGB_ = YES; opacity_ = 255; color_ = colorUnmodified_ = ccWHITE; capSize=capSizeInPixels=CGSizeZero; //Not used blendFunc_.src = CC_BLEND_SRC; blendFunc_.dst = CC_BLEND_DST; // update texture (calls updateBlendFunc) [self setTexture:nil]; // default transform anchor anchorPoint_ = ccp(0.5f, 0.5f); vertexDataCount=24; vertexData = (ccV2F_C4F_T2F*) malloc(vertexDataCount * sizeof(ccV2F_C4F_T2F)); [self setTextureRectInPixels:CGRectZero untrimmedSize:CGSizeZero]; } return self; } -(id) initWithTexture:(CCTexture2D*)texture rect:(CGRect)rect { NSAssert(texture!=nil, @"Invalid texture for sprite"); // IMPORTANT: [self init] and not [super init]; if( (self = [self init]) ) { [self setTexture:texture]; [self setTextureRect:rect]; } return self; } -(id) initWithTexture:(CCTexture2D*)texture { NSAssert(texture!=nil, @"Invalid texture for sprite"); CGRect rect = CGRectZero; rect.size = texture.contentSize; return [self initWithTexture:texture rect:rect]; } -(id) initWithFile:(NSString*)filename { NSAssert(filename!=nil, @"Invalid filename for sprite"); CCTexture2D *texture = [[CCTextureCache sharedTextureCache] addImage: filename]; if( texture ) return [self initWithTexture:texture]; return nil; } +(id)spriteWithFile:(NSString*)f { return [[self alloc] initWithFile:f]; } - (void) dealloc { if (vertexData) free(vertexData); } -(void) updateColor { ccColor4F color4; color4.r=(float)color_.r/255.0f; color4.g=(float)color_.g/255.0f; color4.b=(float)color_.b/255.0f; color4.a=(float)opacity_/255.0f; for (int i=0; i<vertexDataCount; i++) { vertexData[i].colors=color4; } } -(void)updateTextureCoords:(CGRect)rect { CCTexture2D *tex = texture_; if(!tex) return; float atlasWidth = (float)tex.pixelsWide; float atlasHeight = (float)tex.pixelsHigh; float left,right,top,bottom; left = rect.origin.x/atlasWidth; right = left + rect.size.width/atlasWidth; top = rect.origin.y/atlasHeight; bottom = top + rect.size.height/atlasHeight; // // |/|/|/| // CGSize capTexCoordsSize=CGSizeMake(capSizeInPixels.width/atlasWidth, capSizeInPixels.height/atlasHeight); // From left to right //Top band // Left vertexData[0].texCoords=(ccTex2F){left,top}; vertexData[1].texCoords=(ccTex2F){left,top+capTexCoordsSize.height}; vertexData[2].texCoords=(ccTex2F){left+capTexCoordsSize.width,top}; vertexData[3].texCoords=(ccTex2F){left+capTexCoordsSize.width,top+capTexCoordsSize.height}; // Center vertexData[4].texCoords=(ccTex2F){right-capTexCoordsSize.width,top}; vertexData[5].texCoords=(ccTex2F){right-capTexCoordsSize.width,top+capTexCoordsSize.height}; // Right vertexData[6].texCoords=(ccTex2F){right,top}; vertexData[7].texCoords=(ccTex2F){right,top+capTexCoordsSize.height}; //Center band // Left vertexData[8].texCoords=(ccTex2F){left,bottom-capTexCoordsSize.height}; vertexData[9].texCoords=(ccTex2F){left,top+capTexCoordsSize.height}; vertexData[10].texCoords=(ccTex2F){left+capTexCoordsSize.width,bottom-capTexCoordsSize.height}; vertexData[11].texCoords=(ccTex2F){left+capTexCoordsSize.width,top+capTexCoordsSize.height}; // Center vertexData[12].texCoords=(ccTex2F){right-capTexCoordsSize.width,bottom-capTexCoordsSize.height}; vertexData[13].texCoords=(ccTex2F){right-capTexCoordsSize.width,top+capTexCoordsSize.height}; // Right vertexData[14].texCoords=(ccTex2F){right,bottom-capTexCoordsSize.height}; vertexData[15].texCoords=(ccTex2F){right,top+capTexCoordsSize.height}; //Bottom band //Left vertexData[16].texCoords=(ccTex2F){left,bottom}; vertexData[17].texCoords=(ccTex2F){left,bottom-capTexCoordsSize.height}; vertexData[18].texCoords=(ccTex2F){left+capTexCoordsSize.width,bottom}; vertexData[19].texCoords=(ccTex2F){left+capTexCoordsSize.width,bottom-capTexCoordsSize.height}; // Center vertexData[20].texCoords=(ccTex2F){right-capTexCoordsSize.width,bottom}; vertexData[21].texCoords=(ccTex2F){right-capTexCoordsSize.width,bottom-capTexCoordsSize.height}; // Right vertexData[22].texCoords=(ccTex2F){right,bottom}; vertexData[23].texCoords=(ccTex2F){right,bottom-capTexCoordsSize.height}; } -(void) updateVertices { float left=0; //-spriteSizeInPixels.width*0.5f; float right=left+contentSize_.width; float bottom=0; //-spriteSizeInPixels.height*0.5f; float top=bottom+contentSize_.height; float holeLeft=holeRect.origin.x*CC_CONTENT_SCALE_FACTOR(); float holeRight=holeLeft+holeRect.size.width*CC_CONTENT_SCALE_FACTOR(); float holeBottom=holeRect.origin.y*CC_CONTENT_SCALE_FACTOR(); float holeTop=holeBottom+holeRect.size.height*CC_CONTENT_SCALE_FACTOR(); // // |/|/|/| // // From left to right //Top band // Left vertexData[0].vertices=(ccVertex2F){left,top}; vertexData[1].vertices=(ccVertex2F){left,holeTop}; vertexData[2].vertices=(ccVertex2F){holeLeft,top}; vertexData[3].vertices=(ccVertex2F){holeLeft,holeTop}; // Center vertexData[4].vertices=(ccVertex2F){holeRight,top}; vertexData[5].vertices=(ccVertex2F){holeRight,holeTop}; // Right vertexData[6].vertices=(ccVertex2F){right,top}; vertexData[7].vertices=(ccVertex2F){right,holeTop}; //Center band // Left vertexData[8].vertices=(ccVertex2F){left,holeBottom}; vertexData[9].vertices=(ccVertex2F){left,holeTop}; vertexData[10].vertices=(ccVertex2F){holeLeft,holeBottom}; vertexData[11].vertices=(ccVertex2F){holeLeft,holeTop}; // Center vertexData[12].vertices=(ccVertex2F){holeRight,holeBottom}; vertexData[13].vertices=(ccVertex2F){holeRight,holeTop}; // Right vertexData[14].vertices=(ccVertex2F){right,holeBottom}; vertexData[15].vertices=(ccVertex2F){right,holeTop}; //Bottom band //Left vertexData[16].vertices=(ccVertex2F){left,bottom}; vertexData[17].vertices=(ccVertex2F){left,holeBottom}; vertexData[18].vertices=(ccVertex2F){holeLeft,bottom}; vertexData[19].vertices=(ccVertex2F){holeLeft,holeBottom}; // Center vertexData[20].vertices=(ccVertex2F){holeRight,bottom}; vertexData[21].vertices=(ccVertex2F){holeRight,holeBottom}; // Right vertexData[22].vertices=(ccVertex2F){right,bottom}; vertexData[23].vertices=(ccVertex2F){right,holeBottom}; } -(void) setHole:(CGRect)r inRect:(CGRect)totalSurface { holeRect=r; self.contentSize=totalSurface.size; holeRect.origin=ccpSub(holeRect.origin,totalSurface.origin); CGPoint holeCenter=ccp(holeRect.origin.x+holeRect.size.width*0.5f,holeRect.origin.y+holeRect.size.height*0.5f); self.anchorPoint=ccp(holeCenter.x/contentSize_.width,holeCenter.y/contentSize_.height); //[self updateTextureCoords:rectInPixels_]; [self updateVertices]; [self updateColor]; } -(void) draw { BOOL newBlend = NO; if( blendFunc_.src != CC_BLEND_SRC || blendFunc_.dst != CC_BLEND_DST ) { newBlend = YES; glBlendFunc( blendFunc_.src, blendFunc_.dst ); } glBindTexture(GL_TEXTURE_2D, [texture_ name]); glVertexAttribPointer(kCCVertexAttrib_Position, 2, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[0].vertices); glVertexAttribPointer(kCCVertexAttrib_TexCoords, 2, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[0].texCoords); glVertexAttribPointer(kCCVertexAttrib_Color, 4, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[0].colors); glDrawArrays(GL_TRIANGLE_STRIP, 0, 8); glVertexAttribPointer(kCCVertexAttrib_Position, 2, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[8].vertices); glVertexAttribPointer(kCCVertexAttrib_TexCoords, 2, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[8].texCoords); glVertexAttribPointer(kCCVertexAttrib_Color, 4, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[8].colors); glDrawArrays(GL_TRIANGLE_STRIP, 0, 8); glVertexAttribPointer(kCCVertexAttrib_Position, 2, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[16].vertices); glVertexAttribPointer(kCCVertexAttrib_TexCoords, 2, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[16].texCoords); glVertexAttribPointer(kCCVertexAttrib_Color, 4, GL_FLOAT, GL_FALSE, sizeof(ccV2F_C4F_T2F), &vertexData[16].colors); glDrawArrays(GL_TRIANGLE_STRIP, 0, 8); if( newBlend ) glBlendFunc(CC_BLEND_SRC, CC_BLEND_DST); } -(void)setTextureRectInPixels:(CGRect)rect untrimmedSize:(CGSize)untrimmedSize { rectInPixels_ = rect; rect_ = CC_RECT_PIXELS_TO_POINTS( rect ); //[self setContentSizeInPixels:untrimmedSize]; [self updateTextureCoords:rectInPixels_]; } -(void)setTextureRect:(CGRect)rect { CGRect rectInPixels = CC_RECT_POINTS_TO_PIXELS( rect ); [self setTextureRectInPixels:rectInPixels untrimmedSize:rectInPixels.size]; } // // RGBA protocol // #pragma mark CCSpriteHole - RGBA protocol -(GLubyte) opacity { return opacity_; } -(void) setOpacity:(GLubyte) anOpacity { opacity_ = anOpacity; // special opacity for premultiplied textures if( opacityModifyRGB_ ) [self setColor: (opacityModifyRGB_ ? colorUnmodified_ : color_ )]; [self updateColor]; } - (ccColor3B) color { if(opacityModifyRGB_){ return colorUnmodified_; } return color_; } -(void) setColor:(ccColor3B)color3 { color_ = colorUnmodified_ = color3; if( opacityModifyRGB_ ){ color_.r = color3.r * opacity_/255; color_.g = color3.g * opacity_/255; color_.b = color3.b * opacity_/255; } [self updateColor]; } -(void) setOpacityModifyRGB:(BOOL)modify { ccColor3B oldColor = self.color; opacityModifyRGB_ = modify; self.color = oldColor; } -(BOOL) doesOpacityModifyRGB { return opacityModifyRGB_; } #pragma mark CCSpriteHole - CocosNodeTexture protocol -(void) updateBlendFunc { if( !texture_ || ! [texture_ hasPremultipliedAlpha] ) { blendFunc_.src = GL_SRC_ALPHA; blendFunc_.dst = GL_ONE_MINUS_SRC_ALPHA; [self setOpacityModifyRGB:NO]; } else { blendFunc_.src = CC_BLEND_SRC; blendFunc_.dst = CC_BLEND_DST; [self setOpacityModifyRGB:YES]; } } -(void) setTexture:(CCTexture2D*)texture { // accept texture==nil as argument NSAssert( !texture || [texture isKindOfClass:[CCTexture2D class]], @"setTexture expects a CCTexture2D. Invalid argument"); texture_ = texture; [self updateBlendFunc]; } -(CCTexture2D*) texture { return texture_; } @end but now positioning and scaling seem to not work? and it starts in the wrong position... but changing the opacity still works. so i was wondering if anyone can see why my 2.0 version is not working? or if maybe there is a better way to do a sprite hole with cocos2d/opengl 2.0? shaders? thanks

    Read the article

  • Audio comes out of both headphone and speaker at the same time.. Ubuntu 12.04LTS [closed]

    - by pst007x
    I have the same issue on an Aspire. Ubuntu 12.04LTS 64bit realtek audio sound chip onboard If I plug in a headset, audio does not switch from internal speaker to headset, instead plays out of both at the same time. I have looked at the alsamixer setting, all on. I installed gnome-alsamixer, and I noticed headphone was ticked, if I untick the main audio mutes, and the headphone no longer works. Headset only works with internal speaker. Audio works fine on my other desktop and laptop running this release 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) salvatore@salvatore-Aspire-7730:~$ cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.24. salvatore@salvatore-Aspire-7730:~$ head -n 1 /proc/asound/card*/codec#* ==> /proc/asound/card0/codec#0 <== Codec: Realtek ALC888 ==> /proc/asound/card0/codec#1 <== Codec: LSI ID 1040 ==> /proc/asound/card0/codec#2 <== Codec: Intel Cantiga HDMI salvatore@salvatore-Aspire-7730:~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: ALC888 Analog [ALC888 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC888 Digital [ALC888 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 salvatore@salvatore-Aspire-7730:~$ uname -a Linux salvatore-Aspire-7730 3.2.0-23-generic #36-Ubuntu SMP Tue Apr 10 20:39:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux salvatore@salvatore-Aspire-7730:~$ The alsa-base.conf does not exist Tried this: sudo apt-get remove --purge alsa-base sudo apt-get remove --purge pulseaudio sudo apt-get install alsa-base sudo apt-get install pulseaudio sudo alsa force-reload Then: sudo apt-get purge pulseaudio gstreamer0.10-pulseaudio sudo apt-get install pulseaudio gstreamer0.10-pulseaudio indicator-sound Tred this. sudo gedit Then open terminal: sudo /etc/modprobe.d/alsa-base.conf At the end of the file add a new line: options snd-hda-intel model=generic Save and then reboot But alsa-base.conf does not exist

    Read the article

  • Inactive JSRs looking for Spec Leads

    - by heathervc
    You may have noticed that some JSRs have a classification of "Inactive" on their JSR page.  The introduction of this term in 2009 was part of an effort to enable and encourage more transparency into the development of JSRs.  You can read more about Inactive JSRs here and also in the JCP FAQ.The following JSR proposals have been Inactive since at least 2009. If you are a JCP Member and are interested in taking over the Specification Lead role for one of these JSRs, please contact the PMO at [email protected] on or before 23 April 2012. With that message, please include the following: the subject line "Spec Lead for JSR ###," where '###' is the JSR number which JCP Member you represent why you wish to take over the Specification lead role Here is the current list of Inactive JSRs for which Members can request to become Specification Leads: JSR 122, JAIN JCAT JSR 161, JAIN ENUM API Specification JSR 182, JPay - Payment API for the Java Platform JSR 210, OSS Service Quality Management API JSR 241, The Groovy Programming Language JSR 251, Pricing API JSR 278, Resource Management API for Java ME JSR 304, Mobile Telephony API v2 JSR 305, Annotations for Software Defect Detection JSR 320, Services Framework

    Read the article

  • How to deal with the need to know multiple programming languages? When to stop learning new languages?

    - by Raphael
    I am a relatively young programmer. I am 23 and I have been programming professionally for about 5 years. As most programmers I started with C, learned some x86 assembly for fun and then I found C++ which turned out to be my greatest passion in the programming world. Programming with C and C++ forces you to learn platform specific APIs, libs and frameworks all of each requires constant study and experimentation. After some time I had to move on to Java and C# as the demand on my region is basically for these languages. With these languages I entered the world of web development and then I had to learn javascript. Developing for the .NET Framework was exciting at first but I constantly felt as I was getting tied up by Microsoft (and of course the .NET Framework was driving me away from Linux). For desktop development I could do pretty much everything I did with .NET using C++ with Qt but for web development I had to look for an alternative. Quickly I found Django and then I proceeded to learn Python so I could use Django. Nowadays I am learning iOS development with Objective-C. So far it was pretty much easy to learn all these languages (C++ trained me well) but I am worried that someday I won't be able to keep track of them all. Just to clarify. The only languages I learned cause I had to were C# and Java. All of the others I learned for fun, because I love programming and learning new things. Also I like to keep my skills sharp on desktop, web and mobile development. My question is: How do you keep track of multiple programming languages? (I mean, keep track of changes to these languages and keep your skills sharp) and: Is there such a thing as enough programming languages?

    Read the article

  • Strategy for hosting 700+ domains names, each with a static HTML site

    - by jonschlinkert
    I have a portfolio of more than 700 domain names, and ideally I'd like to put up a single-page HTML/CSS/JavaScript webpage for each domain. Is there a system/strategy/workflow that will allow me to: Automate the deployment of new websites, quickly and easily without having to manually initiate each new website in an admin panel. For instance, I've seen dropbox-based solutions that claim to make it simple to setup new websites on your dropbox account, but you still have to set each one up in an admin interface first. It would be so much easier to have a folder naming convention that allowed the user to easily clone/copy/duplicate sites inside their Dropbox App folder (https://www.dropbox.com/developers/blog/23) to create new ones. Sounds interesting, however... It's easy to manage CNAMEs on the registrar-side, but is there a way to quickly associate CNAMEs with new websites (on the hosting side), maybe using the method offered by gh-pages-style (https://help.github.com/articles/setting-up-a-custom-domain-with-pages)? With GitHub's gh-pages, all you have to do is drop a file called CNAME into your repo, with the domain name you want associated with the repo inside the file. gh-pages isn't a good solution for what I'm doing though unfortunately. I'm also a front-end developer, specializing in rapid web development and "front-end build systems", so I building and maintaining static assets for hundreds of sites is no problem. It's the hosting-side that I really struggle with. Any suggestions?

    Read the article

  • Where does the YouTube video files stored on system nowadays?

    - by souravc
    When I open a youtube video with firefox I could not find any video file inside ~/.mozilla/firefox/<some_string>.default/Cache/. I also tried with google-chrome like, ps ax | grep flash ls -l /proc/[*PID*]/fd | grep Flash But again /proc/[*PID*]/fd does not have any video like file. ls -l /proc/[*PID*]/fd have some results like lrwx------ 1 root root 64 Nov 9 12:18 22 -> /run/shm/.com.google.Chrome.eOsHNu (deleted) lrwx------ 1 root root 64 Nov 9 12:18 23 -> /run/shm/.com.google.Chrome.p8h6BL (deleted) Result of ls -l /proc/[*PID*]/fd | grep Flash for some videos from other site is like lrwx------ 1 root root 64 Nov 9 12:35 26 -> /home/username/.config/google-chrome/Default/Pepper Data/Shockwave Flash/.com.google.Chrome.QMzxP8 (deleted) But could not be copied. Then what are the places where firefox or google-chrome stores the streaming videos? And is it possible to recover(copy) a video from there to watch them offline? P.S I have other ways(downloaders) to have streaming videos, but my question is very specific.

    Read the article

  • Calendar issue in simple java form using swing package?

    - by Rand Mate
    I have created a form using java swing package, For the purpose of adding Date of Birth in the form I have used the following code particularly to add in java Frame via Swing Package. Is there any alternative way to simplify the code. JLabel l2 = new JLabel("Date of Birth"); l2.setBounds(200,160,100,20); String day[] ={"1","2","3","4","5","6","7","8","9","10","11","12","13","14","15","16","17","18","19","20","21","22","23","24","25","26","27","28","29","30"}; String month[] = {"Jan", "Feb", "Mar", "Apr", "May", "Jun", "Jul", "Aug", "Sep", "Oct", "Nov", "Dec"}; String year[] = {"2012","2011","2010","2009","2008","2007","2006","2005","2004","2003","2002","2001","2000","1999","1998","1997","1996","1995","1994","1993","1992","1991","1990","1989","1988","1987","1986","1985","1984","1983","1982","1981","1980","1979","1976","1975"}; JComboBox cb1 = new JComboBox(day); cb1.setBounds(450,160,50,20); JComboBox cb2 = new JComboBox(month); cb2.setBounds(500,160,50,20); JComboBox cb3 = new JComboBox(year); cb3.setBounds(550,160,60,20);

    Read the article

  • How do I connect to a wireless network?

    - by Keith Groben
    I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

    Read the article

  • Oracle OpenWorld & JavaOne + Develop 2010

    - by [email protected]
    ?????? ?????????? ????????? ??????????? ??? ?????????? Oracle OpenWorld 2010 19-23 ???????? 2010 Moscone Center, San Francisco, CA ?? ??????????? Oracle Openworld 2010 ?????? ???????????? ??????????? - Applications, Database, Middleware - ? ?????????????? ??????? Oracle, ????? ??????? ???????????? ??????? ? ??????? ???????? (Server and Storage Systems) ? ????? ??? 50 ???????.    ???????? ????? ????????? ?????????? ????? ?? ??????????? ????? ??????????? ????????? ??????? ????? ?????????? ? ??????????? ????? ???????? ? ?????????? ?? ???????? Oracle ? ?????????? ?? ?????? ? ?????????? 

    Read the article

  • Loading Entities Dynamically with Entity Framework

    - by Ricardo Peres
    Sometimes we may be faced with the need to load entities dynamically, that is, knowing their Type and the value(s) for the property(ies) representing the primary key. One way to achieve this is by using the following extension methods for ObjectContext (which can be obtained from a DbContext, of course): 1: public static class ObjectContextExtensions 2: { 3: public static Object Load(this ObjectContext ctx, Type type, params Object [] ids) 4: { 5: Object p = null; 6:  7: EntityType ospaceType = ctx.MetadataWorkspace.GetItems<EntityType>(DataSpace.OSpace).SingleOrDefault(x => x.FullName == type.FullName); 8:  9: List<String> idProperties = ospaceType.KeyMembers.Select(k => k.Name).ToList(); 10:  11: List<EntityKeyMember> members = new List<EntityKeyMember>(); 12:  13: EntitySetBase collection = ctx.MetadataWorkspace.GetEntityContainer(ctx.DefaultContainerName, DataSpace.CSpace).BaseEntitySets.Where(x => x.ElementType.FullName == type.FullName).Single(); 14:  15: for (Int32 i = 0; i < ids.Length; ++i) 16: { 17: members.Add(new EntityKeyMember(idProperties[i], ids[i])); 18: } 19:  20: EntityKey key = new EntityKey(String.Concat(ctx.DefaultContainerName, ".", collection.Name), members); 21:  22: if (ctx.TryGetObjectByKey(key, out p) == true) 23: { 24: return (p); 25: } 26:  27: return (p); 28: } 29:  30: public static T Load<T>(this ObjectContext ctx, params Object[] ids) 31: { 32: return ((T)Load(ctx, typeof(T), ids)); 33: } 34: } This will work with both single-property primary keys or with multiple, but you will have to supply each of the corresponding values in the appropriate order. Hope you find this useful!

    Read the article

  • Nvidia GeForce Gt-520M-cn on intel dh61ww Ubuntu 12.04

    - by j goseeped
    hi people i hope you can help a little bit , i appreciate your time look: i have a this desktop i7 2600, 8gb ram ddr3, board intel dh61ww, Geforce Nvidia GT520-cn 2Gb ddr3, i just install ubuntu 64bits 12.04 kernel 3.2.0-23-generic , i want to setup two monitors samsung led 22" and get start mi video card 1) i download and installed nvidia driver 295.59 and also try with 302.17 to apt-update and upgrade, apt-get install build-essential linux-headers-$(uname -r), apt-get remove --purge nvidia*, apt-get remove --purge xserver-xorg-video-nouveau, vim /etc/modprobe.d/blacklist.conf blacklist vga16fb blacklist nouveau blacklist rivafb blacklist nvidiafb blacklist rivatv sh NVIDIA.run, sudo service lightdm start, reboot, nvidia-xorgconf 2)after reboot i get 800x600 and nvidia-settings say this. You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run nvidia-xconfig as root), and restart the X server. 3) i change a little bit xorg.conf to set up a resolution to work property 4) i dont have any image in the monito and i dont have any option on Nvidia X server settings lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 520] (rev a1) egrep -i 'glx|nvidia' /var/log/Xorg.0.log [ 12.005] (II) LoadModule: "glx" [ 12.005] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 12.575] (II) Module glx: vendor="NVIDIA Corporation" [ 12.585] (II) NVIDIA GLX Module 302.17 Tue Jun 12 16:22:45 PDT 2012 [ 12.585] (II) Loading extension GLX [ 13.037] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event10) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event9) glxinfo | grep direct Xlib: extension "GLX" missing on display ":0.0". Error: couldn't find RGB GLX visual or fbconfig sorry my english is no very well. and thanks guys

    Read the article

  • Get Func-y v2.0

    - by PhubarBaz
    In my last post I talked about using funcs in C# to do async calls in WinForms to free up the main thread for the UI. In that post I demonstrated calling a method and then waiting until the value came back. Today I want to talk about calling a method and then continuing on and handling the results of the async call in a callback.The difference is that in the previous example although the UI would not lock up the user couldn't really do anything while the other thread was working because it was waiting for it to finish. This time I want to allow the user to continue to do other stuff while waiting for the thread to finish.Like before I have a service call I want to make that takes a long time to finish defined in a method called MyServiceCall. We need to define a callback method takes an IAsyncResult parameter.public ServiceCallResult MyServiceCall(int param1)...public int MyCallbackMethod(IAsyncResult ar)...We start the same way by defining a delegate to the service call method using a Func. We need to pass an AsyncCallback object into the BeginInvoke method. This will tell it to call our callback method when MyServiceCall finishes. The second parameter to BeginInvoke is the Func delegate. This will give us access to it in our callback.Func<int, ServiceCallResult> f = MyServiceCall;AsyncCallback callback =   new AsyncCallback(MyCallbackMethod);IAsyncResult async = f.BeginInvoke(23, callback, f); Now let's expand the callback method. The IAsyncResult parameter contains the Func delegate in its AsyncState property. We call EndInvoke on that Func to get the return value.public int MyCallbackMethod(IAsyncResult ar){    Func<int, ServiceCallResult> delegate =        (Func<int, ServiceCallResult>)ar.AsyncState;    ServiceCallResult result = delegate.EndInvoke(ar);}There you have it. Now you don't have to make the user wait for something that isn't critical to the loading of the page.

    Read the article

  • AR242x / AR542x wireless card not working

    - by Pipan87
    My wifi worked perfect until I updated to the latest version of Ubuntu. Now I don't find any wireless connections at all. I have tried lots of guides on the internet but I can't get it to work. I did however start to work once after writing something I don't remember in Terminal, but after rebooting it stopped working again. Some info (don't know if you need more to help): 01:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: Acer Incorporated [ALI] Device 022c Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at 55200000 (64-bit, non-prefetchable) [size=256K] I/O ports at 3000 [size=128] Capabilities: [40] Power Management version 2 Capabilities: [48] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [58] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [180] Device Serial Number ff-93-2e-de-00-23-8b-ff Kernel driver in use: ATL1E Kernel modules: atl1e 02:00.0 Ethernet controller: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Foxconn International, Inc. Device e00d Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at 54100000 (64-bit, non-prefetchable) [size=64K] Capabilities: [40] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [60] Express Legacy Endpoint, MSI 00 Capabilities: [90] MSI-X: Enable- Count=1 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Kernel driver in use: ath5k Kernel modules: ath5k

    Read the article

  • error: no such partition after 11.10 upgrade to 12.04

    - by Alan King
    -I recently upgraded my 11.10 install to 12.04 LTS and got the above error message upon reboot after a GNU GRUB version ubuntu3 display showing Ubuntu 3.2.0-23-generic pae and other kernels or memory tests to choose from. The upgrade had to be done by CD because the Update Manager did not show the 12.04 upgrade option. After selecting the default install option of upgrading 11.10 to 12.04, I was presented with a screen saying that I had not specified a swap partition. Upon selection the 'back' key, I was taken to a partition page which listed two current partitions (only Ubuntu 11.10 had been installed - no Windoz): an ext4 partition plus a small 1.8GB partition. I double clicked the small partition and selected it as the swap partition even though I wondered at the time why this even came up. I can see the two user folders under home from the file manager screen while runnning 12.04 from the CD but if I try to access either one an error message is displayed saying I do not have permission while I get a loading message in the lower right corner of the window that does not go away. I have two questions: Can I access the user folders prior to recovery via the Terminal? If so, how? How do I fix the GRUB issue?

    Read the article

  • loss of sound in ubuntu 12.04

    - by Leo Simon
    I'm running Linux E6520 3.2.0-56-generic #86-Ubuntu SMP Wed Oct 23 09:20:45 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux on a Dell Latitude E6530. (This is a new machine; have run the same version of linux on an older machine for a year, without this happening.) I've been losing sound regularly, though have not been able to isolate the trigger for this. I've scoured the web on this subject, in particular https://help.ubuntu.com/community/SoundTroubleshootingProcedure and Audio stopped working suddenly in 12.04 Nothing from the first site seemed to work for me. From the second site, I learned enough to be able to fix the problem when it happens, but nothing on the web has helped me figure out why the problem is happening in the first place. Patching together stuff from the web, and with some blind luck, I've found that the following steps seem to restore sound pulseaudio --kill pulseaudio --start pavucontrol -> output devices Click on the "Mute audio" icon, which mutes audio Click on the "Mute audio" icon, which unmutes audio. This obviously doesn't make sense: audio wasn't muted in the first place, but somehow, magically, toggling mute audio off and on seems to reset something. Can anybody suggest from this information why sound would be disappearing in the first place (it seems as though something is getting muted at the system level, but I don't know what)? a simpler (command-line/script) way of restoring sound, in particular, is it possible to reset pavucontrol from the commandline? Some other pieces of information that may be of use: The problem is clearly happening at the system level, since I've set up a clean new user, and this user has the same problems that I do. So user fixes like deleting the .pulse directory aren't (and don't) help. Sound works fine in Windows (dual-boot) so it's not a hardware problem Any help/suggestions on this would be most appreciated.

    Read the article

  • Get the Latest Security Inside Out Newsletter, October Edition

    - by Troy Kitch
    The latest October edition of the Security Inside Out newsletter is now available and covers the following important security news: Securing Oracle Database 12c: A Technical Primer The new multitenant architecture of Oracle Database 12c calls for adopting an updated approach to database security. In response, Oracle security experts have written a new book that is expected to become a key resource for database administrators. Find out how to get a complimentary copy.  Read More HIPAA Omnibus Rule Is in Effect: Are You Ready? On September 23, 2013, the HIPAA Omnibus Rule went into full effect. To help Oracle’s healthcare customers ready their organizations for the new requirements, law firm Ballard Spahr LLP and the Oracle Security team hosted a webcast titled “Addressing the Final HIPAA Omnibus Rule and Securing Protected Health Information.” Find out three key changes affecting Oracle customers.  Read More The Internet of Things: A New Identity Management Paradigm By 2020, it’s predicted there will be 50 billion devices wirelessly connected to the internet, from consumer products to highly complex industrial and manufacturing equipment and processes. Find out the key challenges of protecting identity and data for the new paradigm called the Internet of Things.  Read More

    Read the article

  • Can't connect nonlocally after 12.10 upgrade

    - by user101815
    I've just upgraded one of my systems from 12.04 to 12.10. Now I can't connect on that system beyond my local network. Connections within the local network seem to work fine, and I can make nonlocal connections from other machines (like the one I'm asking this question from). I suspect that some routing information has been messed up, but I don't know where to look for it. It's not a nameserver problem -- pinging outside sites by their IP addresses doesn't work either. I have another laptop next to this one, also running Kubuntu 12.10. On the one that can't connect, arp produces no output. On the other one, it produces 192.168.0.1 ether 00:23:69:fa:ce:ae C wlan0 On the working machine, the output of netstat starts with some tcp entries. On the nonworking one, those entries are absent. I asked this question on the Ubuntu forum but haven't gotten any answers there. One further complication: since the troublesome machine has no outside connection, it's extremely difficult to download anything to it. For what it's worth, "ping 8.8.8.8" produces "connect: Network is unreachable". Update: after a lot of fiddling, I have my external world back. I don't know what the key action was, but the first indication of progress was that "ping 8.8.8.8" worked. At that point I still didn't have a working nameserver, so external URLs didn't work. But I did this (based on an online post, of course): sudo dpkg-reconfigure resolvconf and answered Yes to all prompts. That did the trick!! Apparently my problem was unique, or close to it, since I couldn't find any online references to it: local net working, remote net not working, including explicit IP addresses. So I suppose that if no one else has this problem, no one cares about the solution!!

    Read the article

  • Less graphics power all the sudden (Intel HD 3000)

    - by queueoverflow
    I have a Intel Sandy Bridge i5 with the HD 3000 graphics card. I used to be able to play Urban Terror and Nexuiz comfortably with 85 and 60 frames per seconds until mid/end of October 2012, the former even on a full HD display with that many frames. Now I have around 30 to 45 on the smaller laptop screen and around 20 to 30 on the external monitor. Did something happen to Kubuntu 12.04 so that it has less graphics performance than previously? Update I looked into the system monitor and could not detect anything being at the maximum. The four CPU cores were pretty much bored, the 8 GB RAM were filled with maybe 2 GB. And I ran intel_cpu_top and did not notice anything at its limit. See the output. after Kernel bisecting I now did a kernel bisect and tried 3.2.0-23, 3.2.0-27, 3.2.0-29 and 3.2.0-30 and all had full graphics power. Interestingly, I then had full power when I just booted back into the regular 3.2.0-32 kernel. This does not make sense to me …

    Read the article

  • SANS Mobility Policy Survey Webcast follow up

    - by Darin Pendergraft
    Hello Everyone!  If you missed the SANS mobility survey webcast on October 23 - here is a link to the replay and to the slides: [Warning -  you have to register to see the replay and to get the slides] https://www.sans.org/webcasts/byod-security-lists-policies-mobility-policy-management-survey-95429 The webcast had a lot of great information about how organizations are setting up and managing their mobile access policies.  Here are a couple of key takeaways: 1.  Who is most concerned about mobile access policy? Security Analysts >> CISOs >> CIOs - the focus is coming from the risk and security office - so what does that mean for the IT teams? 2. How important is mobile policy? 77% said "Critical" or "Extremely Important" - so this means mobile access policies will get a lot of attention.  3. When asked about the state of their mobile policies: Over 35% said they didn't have a mobile access policy and another 35% said they simply ask their employees to sign a usage agreement.  So basically ~70% of the respondents were not actively managing or monitoring mobile access. Be sure to watch the webcast replay for all of the details. Box, Oracle and RSA were all co-sponsors of the survey and webcast and all were invited to give a brief presentation at the end.

    Read the article

  • Screen flickering / scrambling on an Asus UL30A

    - by user55059
    Recently my Laptop screen started to flicker. You can view the phenomena here: YouTube Sometimes the screen is totally scrambled, but most of the time it starts with the Title bar only. It happens inconsistently. My Laptop is Asus UL30A and I'm using Ubuntu 11.10. Output from command: sudo lshw -C display; lsb_release -a; uname -a; xrandr *-display:0 description: VGA compatible controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 07 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:44 memory:fe400000-fe7fffff memory:d0000000-dfffffff ioport:dc00(size=8) *-display:1 UNCLAIMED description: Display controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 07 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:fe800000-fe8fffff LSB Version: core-2.0-ia32:core-2.0-noarch:core-3.0-ia32:core-3.0-noarch:core-3.1-ia32:core-3.1-noarch:core-3.2-ia32:core-3.2-noarch:core-4.0-ia32:core-4.0-noarch Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric Linux steelke 3.0.0-14-generic-pae #23-Ubuntu SMP Mon Nov 21 22:07:10 UTC 2011 i686 i686 i386 GNU/Linux Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 293mm x 164mm 1366x768 60.0*+ 1360x768 59.8 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 disconnected (normal left inverted right x axis y axis) DP1 disconnected (normal left inverted right x axis y axis) DP2 disconnected (normal left inverted right x axis y axis) I already rolled back the kernel to 3.0.0-14 instead of 3.0.0-17 as mentioned in this post, but without result. I guess the problem is related to the driver, because I don't see similar behaviour in the BIOS Setup. Any tips or help is welcome.

    Read the article

  • Context switches much slower in new linux kernels

    - by Michael Goldshteyn
    We are looking to upgrade the OS on our servers from Ubuntu 10.04 LTS to Ubuntu 12.04 LTS. Unfortunately, it seems that the latency to run a thread that has become runnable has significantly increased from the 2.6 kernel to the 3.2 kernel. In fact the latency numbers we are getting are hard to believe. Let me be more specific about the test. We have a program that has two threads. The first thread gets the current time (in ticks using RDTSC) and then signals a condition variable once a second. The second thread waits on the condition variable and wakes up when it is signaled. It then gets the current time (in ticks using RDTSC). The difference between the time in the second thread and the time in the first thread is computed and displayed on the console. After this the second thread waits on the condition variable once more. So, we get a thread to thread signaling latency measurement once a second as a result. In linux 2.6.32, this latency is somewhere on the order of 2.8-3.5 us, which is reasonable. In linux 3.2.0, this latency is somewhere on the order of 40-100 us. I have excluded any differences in hardware between the two host hosts. They run on identical hardware (dual socket X5687 {Westmere-EP} processors running at 3.6 GHz with hyperthreading, speedstep and all C states turned off). We are changing the affinity to run both threads on physical cores of the same socket (i.e., the first thread is run on Core 0 and the second thread is run on Core 1), so there is no bouncing of threads on cores or bouncing/communication between sockets. The only difference between the two hosts is that one is running Ubuntu 10.04 LTS with kernel 2.6.32-28 (the fast context switch box) and the other is running the latest Ubuntu 12.04 LTS with kernel 3.2.0-23 (the slow context switch box). Have there been any changes in the kernel that could account for this ridiculous slow down in how long it takes for a thread to be scheduled to run?

    Read the article

  • Get Func-y

    - by PhubarBaz
    I was working on a Windows form app and needed a way to call out to a service without blocking the UI. There are a lot of ways to do this but I came up with one that I thought was pretty simple. It utilizes the System.Func<> generic class, which is basically a way to create delegates using generics. It's a lot more compact and simpler than creating delegates for each method you want to call asynchronously. I wanted to get it down to one line of code, but it was a lot simpler to use three lines.In this case I have a MyServiceCall method that takes an integer parameter and returns a ServiceCallResult object.public ServiceCallResult MyServiceCall(int param1)...You start by getting a Func<> object for the method you want to call, in this case MyServiceCall. Then you call BeginInvoke() on the Func passing in the parameter. The two nulls are parameters BeginInvoke expects but can be ignored here. BeginInvoke returns an IAsyncResult object that acts like a handle to the method call. Finally to get the value you call EndInvoke on the Func passing in the IAsyncResult object you got back from BeginInvoke.Func<int, ServiceCallResult> f = MyServiceCall;IAsyncResult async = f.BeginInvoke(23, null, null);ServiceCallResult result = f.EndInvoke(async);Doing it this way fires off a new thread that calls the MyServiceCall() method. This leaves the main application thread free to update the UI while the method call is running so it doesn't become unresponsive.

    Read the article

  • Why do arrays in java choose the biggest? [closed]

    - by Trycon
    I'm new to java so I was reading my book with these code: public class mainb1 { public static void main (String[] args) { //datatype name = expression; //food int min, max; int num[] = new int[10]; num[0]=99; num[1]=90; num[2]=-100; num[3]=100; num[4]=23; num[5]=50; num[6]=123; num[7]=3123; num[8]=2; num[9]=923; min=max=num[1]; for(int x=0;x<10;x++) { if(num[x]<min)min=num[x]; if(num[x]>max)max=num[x]; } System.out.println("Min: "+min+" max: "+max); } } It chose the biggest and the smallest. I don't get it if max was 99, then the last one that is lesser than min is 2? How did this array choose to pick the smallest and the biggest? Can someone explain?

    Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >