Search Results

Search found 29560 results on 1183 pages for 'colin fine'.

Page 69/1183 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

  • Ad-hoc connection between iPhone and Macbook Pro

    - by Phil Nash
    I sometimes find it useful to connect my iPhone to my Macbook Pro by creating an ad-hoc wireless network from the MBP and connecting to that from the iPhone. However, what I find is that sometimes this works and sometimes it doesn't. When it's not working the symptoms are usually that I see the ad-hoc SSID in the list of available networks on the iPhone, can connect to it from there (including entering my WEP key), and it shows up as the wifi network in use. However I don't get the wifi symbol in the taskbar (it remains as 3G) and attempting to use the connection (e.g. trying to connect to iTunes or Keynote using their respective Remote apps) fails saying that there is so wifi connection. I've tried rebooting both the iPhone and the MBP, recreating networks with different SSIDs and tried different channels - all to no avail! I'm especially puzzled that (a) sometimes it works just fine first time and (b) the Settings app seems to think its all connected fine. Is there anything else I should be trying?

    Read the article

  • Apache doesn't autostart because vpn isn't up yet.

    - by Col. Shrapnel
    I have a FreeBSD8 server, and VPN connection to my ISP. I use mpd5 and it works fine. A have an Apache server whch works fine, if I start it manually, after VPN is get up. But when I add it to rc.conf autostart, it fail to start, saying (49) can't assign requested address: make_sock could not bind to address I suppose it's because VPN isn't up yet and no IP address assigned to the interface which i set in the Listen directive in the httpd.conf. If i set Listen to the existing 127.0.0.1, it fail to serve wan requests. Is there a solution, either to delay apache autostart or configure it some different?

    Read the article

  • Unable to connect to network

    - by user33750
    Hey guys, I have a question. I have been having problems connecting a new netbook to my network at home. I have an Asus Eeepc 100HAB. I have tried to run a repair on the connection, uninstalled and re-installed the network card, made sure all of the drivers are up-to-date as well. Two caveats: I have a laptop that I recently switched to a wired connection because it wasn't connecting to the network as well, and the netbook connects to an unsecured network i found just fine, only having a problem getting into my home network. Passwords are correct, and the computer where the connection originates from is working fine as well. Any ideas?

    Read the article

  • Server 2008, 2 NICs, 2 fixed IPs - big delays using internet

    - by user46055
    Hi geniuses I have an all in one Windows 2008 server, configured with AD/DHCP/DNS/RRAS - all set up with wizards and no specific tweaking. The server has 2 network adapters : one of which ("MyWAN") is plugged into our office's internet connection, the other ("MyLAN") is plugged into a local switch, which is also where all our desktops are connected. So this one server is doing everything. When first set up, MyLAN had a fixed IP of 192.168.2.1 and served the desktops with DHCP scope 192.168.2.50-99. It also told them to use 192.168.2.1 as DNS and gateway. MyWAN was setup to take its IP etc from DHCP, being handled by the building's router and ADSL modem etc. All desktops were setup to use DHCP. This all worked perfectly fine, until I recently changed MyWAN to have a static IP (I wanted to access it from home, and needed to give it a static IP to port map in the building's router). Things still work, but there is now a long delay when accessing the internet. The actual speed is as before when downloading, but there is a pause of 3-6 secs when connecting to new hosts (for example if I browse to slashdot from either a desktop or the server itself, it'll hang on connecting to slashdot.org, hang again on connecting to *.fsdn, *.google-analytics.com and all the other hosts referenced from the main page). If I ping slashdot.org from the server, I get the following : Pinging slashdot.org [216.34.181.45] with 32 bytes of data: Reply from 192.168.2.1: Destination host unreachable. Reply from 216.34.181.45: bytes=32 time=99ms TTL=239 Reply from 216.34.181.45: bytes=32 time=100ms TTL=239 Reply from 216.34.181.45: bytes=32 time=101ms TTL=239 Pinging anywhere external always seems to hit 192.168.2.1 first, which doesn't seem right. Trying tracert from the server gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 MYSERVER01.intranet [192.168.2.1] reports: Destination host unreachable Trying tracert from a desktop gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 <1 ms * <1 ms MYSERVER [192.168.2.1] 2 * * * Request timed out. 3 6 ms 6 ms 6 ms dsl-gw1.ge.mer.uk.webtapestry.net [217.151.111.17] 4 38 ms 239 ms 251 ms gw-router.ge.mer.uk.webtapestry.net [217.151.111.13] ...and then all is fine after that. I think that DNS is working fine because the domain names are getting translated to correct IPs immediately. DHCP seems to be okay? So perhaps it's something up with my RRAS setup - although I can't see any option during the setup wizard which I would have filled in differently. I've also tried changing the binding order of the two network connections, to prioritise MyWAN, but that doesn't seem to have done anything. Any idea what's up? Many thanks - Rob

    Read the article

  • Set up SSL/HTTPS in zend application via .htaccess

    - by davykiash
    I have been battling with .htaccess rules to get my SSL setup working right for the past few days.I get a requested URL not found error whenever I try access any requests that does not do through the index controller. For example this URL would work fine if I enter the it manually https://www.example.com/index.php/auth/register However my application has been built in such a way that the url should be this https://www.example.com/auth/register and that gives the requested URL not found error My other URLs such as https://www.example.com/index/faq https://www.example.com/index/blog https://www.example.com/index/terms work just fine. What rule do I need to write in my htaccess to get the URL https://www.example.com/auth/register working? My htaccess file looks like this RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (.*) https://%{HTTP_HOST}%{REQUEST_URI} [L] RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] RewriteRule ^.*$ index.php [NC,L] I posted an almost similar question in stackoverflow

    Read the article

  • Laptop monitor goes black under intense graphics

    - by drahcir
    I have a dell inspiron 1520 with a nvidia GeForce 8600M GT video card. I have Windows 7 professional as an operating system. Yesterday when I was using it the screen started to somewhat flicker then go completely black. I restarted it and in the boot screen everything seems fine, when I entered the login screen it became flickery again, and when I logged in, when a couple of windows popped up it went black again. I hooked it up to a tft monitor and the monitor works fine, and did some more tests that confirmed that under higher graphics causes the laptop monitor to go black. Is there a reason why this is happening?

    Read the article

  • Weird Windows 2003 MSDTC and SQL 2005 issue

    - by seagull surfer
    scenario: Windows 2003 sp2 x64 enterprise edition. SQL 2005 sp2 cu9 x64 Enterprise edition After restarting the resource groups on two node active-active cluster, 3 SQL 2005 instances start up fine. The 4th one starts up but starts throwing the following error. "Enlist operation failed: 0x8004d00e(XACT E NOTRANSACTION). SQL Server could not register with Microsoft Distributed Transaction Coordinator (MS DTC) as a resource manager for this transaction. The transaction may have been stopped by the client or the resource manager." MSDTC is fine since the other 3 function normally. The only way to "fix" it is to take the 4th instance offline and bring it online again. Is there any way to fix this enlistment without restarting?

    Read the article

  • PSKill does not run from VbScript

    - by David
    We have a site on our local IIS6 Windows 2003 server that occasionally locks up, and we would like a VbScript to kill the process. It is located in the system32 folder. I'm running these tests on the local machine. For simplicity, my VbScript file simply has lines such as these: WScript.Echo "PSKill.exe " & W3WP.ProcessId WshShell.Run "PSKill.exe " & W3WP.ProcessId WScript.Echo "Killed Process" Obtained earlier in the script, W3WP.ProcessId contains the correct process ID. The script outputs to the screen: PSKill.exe 6884 But the line that is supposed to execute the command does nothing. If I type the command in, it works fine. Why does PsKill work fine when I type it, but not from VbScript?

    Read the article

  • Snow Leopard, PHP, and MySQL

    - by Peter
    I have just installed Snow Leopard and now my PHP/MySQL program ends in a "Segmentation fault". I have been searching the web for a solution, I realize that there are some issues with SL/PHP/MySQL, but I have not found anything that works yet. I downloaded the binary MySQL package mysql-5.1.42-osx10.6-x86_64. I have updated the php.ini file as suggested at various posts. When I run PHP and connect to the MySQL server the behavior is a bit random. In many cases it works fine to connect and read data. In my specific case the PHP program constructs a LOAD DATA LOCAL INFILE ... statement to load data from a text file. It should do several such queries after each other in a loop. It works one time but the halts in a "Segmentation fault". The program worked fine in Leopard, but not now. My versions are: OS 10.6.2, PHP 5.3.0, MySQL 5.1.42

    Read the article

  • How does one launch PhpPgAdmin?

    - by DarenW
    I just installed postgresql, php5 and in particular PhpPgAdmin using Ubuntu's synaptic app. The PHP is running fine, the http server (lighttpd) is working fine, and I can do pg a the command line. The only thing that remains a mystery is PhpPgAdmin - just how does one fire it up to use it? I am clueless about the proper means of starting PhpPgAdmin; it isn't explained anywhere on the site for it. I tried typing phppgadmin at a bash command prompt, and entering "http://phppgsdmin/" and "http://localhost/phppgadmin" as wild guesses in the address bar in a browser - nothing happens. What is the secret? BTW, i'm only serving http on localhost, doing purely private web development.

    Read the article

  • Network shares do not mount

    - by Alex
    My network shares were mounting fine yesterday.. suddenly they are not. They were mounting fine for the last two weeks or however long since I added them. When I run sudo mount -a I get the following error: topsy@monolyth:~$ sudo mount -a mount error(12): Cannot allocate memory Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) mount error(12): Cannot allocate memory Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) mount error(12): Cannot allocate memory Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) mount error(12): Cannot allocate memory Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) topsy@monolyth:~$ I followed this guide when setting them up: http://ubuntuforums.org/showthread.php?t=288534 So I tried removing them by doing the reverse, and then rebooting, then adding them again and rebooting. Problem persists.

    Read the article

  • Hard freeze on new computer

    - by mphair
    OCZ Gold 3x2GB 240-Pin DDR3 SDRAM PC312800 Palit NE5T240SFHD01 GeForce GT240 1GB 128-bit GDDR5 ASUS P7P55D-E LGA 1156 P55 SATA 6Gb/s USB 3.0 ATX Intel Motherboard Intel Core i7-860 Lynnfield 2.8GHz 8MB L3 Cache LGA 1156 95W Quad-Core Processor SAMSUNG 22X Optical drive (DVD+-R/RW) CORSAIR CMPSU-620HX 620W ATX12V V2.2 Windows 7 Ultimate x64 Brand new system (got it from newegg two days ago) and it booted up and installed windows and ran for a day just fine. Yesterday, I boot it up in the afternoon and run various games at full graphics for most of the day. I turn on WoW and play for a few hours and it hard stalls. No numlock switching, no mouse feedback but nothing going wrong on the screen. No BSOD. I wait a bit to see if the stall is just a temporary one, but then force shutdown the computer. Upon reboot, everything seems fine, windows sees that it didn't shut down properly but I go into normal boot and restart WoW. I'm able to load it up and start running around when it freezes again. This time when I restart, it doesn't even get to BIOS. It starts (power goes on) and it just hangs with no output to the monitors. I shut it off and went to bed. This morning, I turned it on and went into BIOS setup. I'm not terribly experienced with messing with BIOS settings but I checked over them the best I could. Everything seems fine so I boot into windows and browse the internet for a bit looking for a solution, hard freeze within 10 minutes. I restart and go into BIOS and check the CPU temperature, 40c. I'm kinda stumped here. Some people say it might be a memory issue, but why would it take so long for it to come up? Could it have been slowly accessing one memory stick at a time and then it just got to a bad one and that's what is causing it to fail? It seems odd that I don't get a BSOD from a hardware failure. Having the screen just halt with no input or output change seems like a software thing to me. Any thoughts?

    Read the article

  • "Verifying DMI Pool" hang caused by raid array..

    - by Ling
    Hi Experts, I have a problem, I obtained a new server with 4 hard drives (2 500 gig, 2 two TB), and an adeptec RAID card. I arranged them in two arrays with RAID 1 (500 gigs together as primary and the 2 TB drives for lots of data). When both arrays are configured, the server hangs while booting at message "Verifying DMI Pool", however if I remove the second array from the configuration the server boots fine. I have checked they are both on different channels, I have disabled all other peripherals from the boot menu and ensured the hard drive is #1. I have booted into the linux rescue mode and checked that it is reading both arrays fine. What else could be causing these problems? Thanks

    Read the article

  • squid configuration change to accept http request on LAN

    - by Ratan Kumar
    installed squid + dansguardian to block adult content on my linux (ubuntu 12.10) . everything worked fine. it has blocked as expected . now the problem is i am also running an apache server for my LAN . ( kind of website ) but when accessing it via 192.168.0.1 , it says squid has blocked the connection , this is the exact error The following error was encountered while trying to retrieve the URL: http: //192.168.0.16/ Connection to 192.168.0.16 failed. The system returned: (113) No route to host The remote host or network may be down. Please try the request again. Your cache administrator is webmaster. before configuring the squid it was working fine . what changes in the squid.conf i have to make . i tried acl Safe_ports 80 allow_all Safe_ports ( i want to know how i can configure it again to listen HTTP request from LAN )

    Read the article

  • unusual webpage access problem

    - by user28163
    This is one of the weirdest problems I've ever seen and I'm out of ideas. I cannot access a couple of websites from my home pc (for 3-4 days now), or at least they go really really slow ~700b/s I can access these same websites fine from my laptop from same IP address. - The websites originate from different countries and are huge popular sites. - I have tried both my PC's network cards. - I have reformatted my PC. - I have reset my router to factory settings. - I have created virtual computers on my PC, and from inside those I cannot access the webpages. - I have flushed my dns. - I tried specifying my dns server addresses to 8.8.8.8 and 8.8.4.4. I can only access the webpages using my PC, if I first connect to an outside VPN. Again, these sites work fine on the 2 other pcs in this house (same ISP and internet connection). help plz :)

    Read the article

  • Accessing localhost via IIS 7.5 on Windows 7 very slow

    - by Ian Devlin
    (I've asked this over on stackoverflow already, but thought I'd ask here as well) I'm currently running an ASP.NET application on IIS 7.5 on Windows 7. When I access this application on Internet Explorer (either 6, 7 or 8) it is incredible slow and often fails to load at all. There are messages at the bottom saying: Waiting for http://localhost/....... or sometimes waiting for about:blank (I've read that this can be a virus, but I've run all the usual checks and it's not). constantly, but it returns with the usual: "Internet Explorer cannot display the webpage" I've also tried this by using 127.0.0.1 and the machine name, with the same results. I've tried the same application on the latest Firefox, Safari, Chrome and Opera and they all work fine. I've also installed the same application on a Windows Server 2003 machine, and it all works fine via Internet Explorer. I've also turned off the IPv6 setting on the LAN connection. Soes anyone have any ideas why this doesn't work with Internet Explorer and yet does with other browsers?

    Read the article

  • Why doesn't my Droid phone charge when connected to a powered USB hub that is not connected to my computer?

    - by pkaeding
    I notice that my new Motorola Droid phone charges perfectly fine when I connect it to my computer via the USB cable, or if I connect it to a car cigarette lighter-USB adapter, or a wall power-USB adapter. It also works fine when I connect it to a powered USB hub that is connected to my computer. However, if that same powered USB hub is not connected to my computer when I connect the phone, it does not charge. If I connect the computer to the hub, and then connect the phone to the hub, it will charge. If I then disconnect the computer from the hub, the phone will continue to charge. Does anyone know why this is happening, or what I can do to be able to charge my phone from a powered hub, without my computer being present?

    Read the article

  • After virus, IE and Chrome don't work but Firefox does.

    - by Erich
    I recently got rid of a virus on my laptop. Afterwards everything seems to be working fine except for some internet connectivity problems. Internet Explorer and Chrome won't display an webpages, Firefox does but I can't update it to the most recent version. I've also noticed that some of the gadgets on Google Gadgets don't work properly. My internet connection is working fine, especially since I can get to websites via Firefox. I have tried to re-install IE and Chrome, but there was no change. What has caused this and how can I fix it?

    Read the article

  • Copssh, how to add users?

    - by Ken
    I installed copssh on Windows Vista (64-bit) here, and the installation seemed to go fine. It requires you to explicitly add users to log in, which is fine, so I opened the COPSSH Control Panel (really just an app), went to the Users tab, clicked Add, Forward, and the "User:" popup is empty. The "Domain:" popup has exactly one entry: my computer name. The "Documentation" shortcut in the start menu group is broken, but I found the folder it's supposed to point to, and I only see docs for command-line tools (which I'll investigate next). Is there something I'm missing? Is the COPSSH Control Panel just plain broken?

    Read the article

  • Weird problem, special characters after formatting the hard drive, computer not starting 0_o

    - by m3taspl0it
    Hya friends , Last night my computer was working fine. But today when i came back from college and started it , it was starting fine but after sometime it's getting restarted , again and again getting restarted at different points , so i tried to boot it in safe mode but same problem. Now after all this , i finally decided to format the drive C (it is in 80 GB) and load new OS windows XP3. After formatting and loading xp3 sufficient files , when it was getting rebooted for copying the actual os files , it hung and a weird screen came. I've also attached the pic of error : http://www.postimage.org/image.php?v=gxz1vKS My specs : P4 3.0 Ghz 2 GB RAM (2x 512 mb and 1 GB) 3 hard drives { 80 GB (5 years old around) 320 GB ( 2 years old around) 500 GB ( recently bought) 256 MB graphics card any help is very appreciated , thanks

    Read the article

  • pdftk issue after updating Ubuntu from 9.04 to 9.10

    - by Crazydog
    We upgraded our server to 9.10 from 9.04 the other day, and it all went well except for one rather important program. We're using pdftk to automatically generate filled out pdf forms. On 9.04, it worked just fine. After updating to 9.10, the pdf forms would no longer be filled out - they'd just be empty. I discovered that if I try to create an fdf file via pdftk from my PDF form, it just creates an empty fdf with no fields. On windows, pdftk generates the fdf file just fine. Any ideas? Thanks.

    Read the article

  • Quickbooks and Cisco ASA 5505

    - by user41516
    I have a Cisco ASA 5505, and everything has seemed to function fine, however I have had problems with Quickbooks 2008 running super slow over the network (Samba) and narrowed it down to the Cisco box. Other Samba transfers seem to be pretty fast, and the Quickbooks file is not very large at all (<25 MB), and other Samba transfers seem to be fine. However, I'm not sure if Quickbooks uses another protocol or if there are other ports that need to be opened. Can anybody give me any clues on how to resolve or troubleshoot the problem or have any prior experience with running Quickbooks over a network?

    Read the article

  • Exchange Public Folders in Snow Leopard Mail.app

    - by W_P
    I am using Mail.app (running snow leopard) to connect to my email account on my school's Exchange 2007 server. I get my Inbox just fine, and iCal connects to my Outlook Calendar just fine, but I cannot seem to get any of the Exchange Public Folders that I can automatically see when I am using Outlook on a Windows box. The Account Type is shown as "Exchange 2007" I did not have any luck Googling this problem, in fact most of the results I saw were dealing with the opposite problem: Remove MS Exchange Public Folders I am aware that my question is a duplicate of this: http://superuser.com/questions/103115/apple-mail-app-all-exchange-folders-not-visible but since that question did not get any responses, I am reposting.

    Read the article

  • Simplest way to expose UNIX mailboxes via IMAP or POP3 on RHEL 5.6

    - by db2
    We've got a web server running RedHat Enterprise Linux 5.6, and it has all the usual local UNIX mailboxes. As is typical, the root mailbox gets all the cron output, logwatch results, etc. I'd like an easier way to keep an eye on this mailbox besides running mail via ssh. What should I install/enable to allow access to these system mailboxes via IMAP or POP3 with minimal fuss? Either protocol would be fine for what I'm doing, as I could then add it as an account in Outlook. A bit of searching led me to cyrus-imapd and dovecot, but it seems like they are meant for more serious mail hosting operations. Either they use their own mailbox system exclusively, or don't have a simple way of making the UNIX mailboxes available. If I'm wrong about that, then I'm fine with using either of them as long as I can get to the mailboxes of the existing accounts on the box.

    Read the article

  • How do I keep multiple copies of Outlook in sync when using RPC over HTTP?

    - by Don
    I use Outlook 2007 at work with our Exchange 2003 server. I just setup my home system with Outlook 2007 so that I could use the RPC over HTTP to access Exchange without having to use a VPN. It works fine. I can get mail, send mail, etc. What it doesn't seem to be doing is staying in sync. For example, I read a few messages at home, moved them into different folders from the Inbox, etc. That all seemed fine. When I login to my work machine and look at the copy of Outlook there, the mail is still unread and nothing has been moved. Am I missing something simple here? I would have to assume that my home machine should be telling Exchange where these messages belong and that they've been read. Both machines are running Windows 7, if that matters. Ideas?

    Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >