Search Results

Search found 21644 results on 866 pages for 'connection speed'.

Page 69/866 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

  • Linux box acting as wireless access point to share the internet connection

    - by Suresh
    A linux machine is connected to internet over two interfaces ppp0 and ppp1 using two modems. Also this machine acts as wireless access point through an interface say, eth0 with ip address 192.168.1.1 and acts as gateway for the connected devices through this network with subnet mask 255.255.255.0 Now is it possible to achieve the following: When any of the connected devices through wireless AP needs internet connection linux machine has to use ppp1 interface for internet. If any of the applications on the linux machine needs internet connection linux machine should use ppp0 interface for the internet. Can this be achieved by adding rules to chains in filter/nat tables? If the kernel routing table has a default rule to route the default traffic through interface ppp0, wil kernel completely ignore ppp1 for internet? PS: new to networking and routing concepts, If the question is not clear leave a comment, will try to give more information.

    Read the article

  • Troubleshooting an unstable internet connection

    - by Konrad Rudolph
    My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

    Read the article

  • Domain connection shows as "unauthenticated"

    - by gareth89
    I have seen various different questions for this problem floating around but either the circumstances arent the same or the solution doesnt work so thought i would post it to see if anybody has any suggestions. Various domain PCs and laptops appear to randomly give the connection name of "lewis.local 2(Unauthenticated)" - lewis.local being our domain - and provides an exclamation mark where the network type logo is normally shown. This also appears to happen every time connecting via vpn. Our setup is: 2 servers both running windows server 2003 R2 (x32) main server has AD, DNS and DHCP installed IPv4 on approx 30 client machines (some wired, some wireless) If anybody has any thoughts on solutions i would appreciate it. I have tried removing all but AD server roles, resetting all of the systems and nothing. It doesnt prevent anything from working just like a domain connection most of the time however it is getting fustrating! Also dont know if it could have anything to do with it but the DHCP server seems to have quite a long lead time on issuing the IP address to the client.

    Read the article

  • Secure external connection to SQL Server (from third party software)

    - by Bart
    I have a SQL Express 2008 R2 server running on a server in an internal lan network. A few databases are used by some third party software to store data. A SQL-Server user is used by this application to connect to the database. Now I need to access this database using a local installation of the software from an external pc. In this particular case a VPN connection is not the solution I am looking for. I have access to an external linux server, so I tried ssh tunneling from the windows server to the linux server and use the external pc to tunnel it back from the linux server to the client, but this is working very very slow. What are my other options to allow this external connection in a safe way?

    Read the article

  • windows firewall and network location switch after establishing a vpn connection

    - by Konrads
    Hello, I am looking for a reasonable solution for network location switching after VPN connection is established for Windows 7. The scenario is as follows: For location public (employee plugging in his laptop in hotel, public wi-fi,etc) all inbound connections are restricted, only outbound VPN + www is enabled. Employee then initiates a VPN connection, VPN pushes routes to 10.0.0.0/8 subnet Now I would like to have lax security rules for traffic from/to 10.0.0.0/8 that comes through the VPN interface, while still protecting the laptop from traffic that comes via uplink interface as if it was private. How to achieve this switching and duality? One option I see is switching to IPSec...

    Read the article

  • ssh_exchange_identification: Connection closed by remote host?

    - by user51684
    debug1: Connection established. debug1: identity file /home/DAMS/.ssh/id_rsa type 1 debug1: identity file /home/DAMS/.ssh/id_rsa-cert type -1 debug1: identity file /home/DAMS/.ssh/id_dsa type -1 debug1: identity file /home/DAMS/.ssh/id_dsa-cert type -1 ssh_exchange_identification: Connection closed by remote host hello this one is different . no missing or anything. im using cygwin. and it just stop when im doing git push production on my server. usually its ok, but i dont know why its stop connections i wonder whats wrong.

    Read the article

  • Site-to-Site PPTP VPN connection between two Windows Server 2008 R2 servers

    - by steve_eyre
    We have two Windows Server 2008 R2 machines, one in our main office and one in a new office which we have just moved offsite. The main office has previously been handling client-to-server PPTP VPN connections. Now that we have moved our second server out of office, we want to set up a demand-dial or persistent VPN connection from the second server to the primary. Using a custom setting RRAS profile, we have successfully managed to set up a site-to-site VPN connection so that from the second server itself, it can access any of the devices in the main office and communicate back. However, any connected machines in the second office cannot use this connection, even when using the second server as gateway. The demand-dial interface is setup from the Second Server dialing into Main Server and a static route set up on RRAS for 192.168.0.0 with subnet mask 255.255.0.0 pointing down this network interface. The main office has the network of 192.168.0.0/16 (subnet mask 255.255.0.0). The second office has the network of 172.16.100.0/24 (subnet mask 255.255.255.0). What steps do we need to take to ensure traffic from the second office PCs going towards 192.168.x.x addresses use the VPN route? Many Thanks in advance for any help the community can offer. Debug Information Here is the route print output from the second server: =========================================================================== Interface List 23...........................Main Office 22...........................RAS (Dial In) Interface 16...e0 db 55 12 fa 02 ......Local Area Connection - Virtual Network 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 14...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 24...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.222 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 <MAIN OFFICE IP> 255.255.255.255 172.16.100.250 172.16.100.222 6 172.16.100.0 255.255.255.0 On-link 172.16.100.222 261 172.16.100.113 255.255.255.255 On-link 172.16.100.113 306 172.16.100.222 255.255.255.255 On-link 172.16.100.222 261 172.16.100.223 255.255.255.255 On-link 172.16.100.222 261 172.16.100.224 255.255.255.255 On-link 172.16.100.222 261 172.16.100.225 255.255.255.255 On-link 172.16.100.222 261 172.16.100.226 255.255.255.255 On-link 172.16.100.222 261 172.16.100.227 255.255.255.255 On-link 172.16.100.222 261 172.16.100.228 255.255.255.255 On-link 172.16.100.222 261 172.16.100.229 255.255.255.255 On-link 172.16.100.222 261 172.16.100.230 255.255.255.255 On-link 172.16.100.222 261 172.16.100.255 255.255.255.255 On-link 172.16.100.222 261 192.168.0.0 255.255.0.0 192.168.101.87 192.168.101.17 266 192.168.101.17 255.255.255.255 On-link 192.168.101.17 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.222 261 224.0.0.0 240.0.0.0 On-link 172.16.100.113 306 224.0.0.0 240.0.0.0 On-link 192.168.101.17 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.222 261 255.255.255.255 255.255.255.255 On-link 172.16.100.113 306 255.255.255.255 255.255.255.255 On-link 192.168.101.17 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.0.200 Default 0.0.0.0 0.0.0.0 172.16.100.250 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 16 261 fe80::/64 On-link 16 261 fe80::edf4:85c6:3c15:dcbe/128 On-link 1 306 ff00::/8 On-link 16 261 ff00::/8 On-link 22 306 ff00::/8 On-link =========================================================================== Persistent Routes: None And here is the route print from one of the second office PCs: =========================================================================== Interface List 11...10 78 d2 32 53 27 ......Atheros AR8151 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.16.100.250 172.16.100.103 10 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 172.16.100.0 255.255.255.0 On-link 172.16.100.103 266 172.16.100.103 255.255.255.255 On-link 172.16.100.103 266 172.16.100.255 255.255.255.255 On-link 172.16.100.103 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 172.16.100.103 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 172.16.100.103 266 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 11 266 fe80::/64 On-link 11 266 fe80::e973:de17:a045:aa78/128 On-link 1 306 ff00::/8 On-link 11 266 ff00::/8 On-link =========================================================================== Persistent Routes: None

    Read the article

  • Connection from Apache to Tomcat via mod_jk not working

    - by Tobias Schittkowski
    I would like to connect apache to tomcat via mod_jk (same machine). The ajp connector in tomcat is listening on port 8009, the worker settings are: worker.worker1.port=8009 worker.worker1.host=localhost However, the connection fails, here is the mod_jk debug log: [debug] wc_get_name_for_type::jk_worker.c (292): Found worker type 'ajp13' [debug] init_ws_service::mod_jk.c (1097): Service protocol=HTTP/1.1 method=GET ssl=false host=(null) addr=127.0.0.1 name=localhost port=80 auth=(null) user=(null) laddr=127.0.0.1 raddr=127.0.0.1 uri=/share [debug] ajp_get_endpoint::jk_ajp_common.c (3154): acquired connection pool slot=0 after 0 retries [debug] ajp_marshal_into_msgb::jk_ajp_common.c (626): ajp marshaling done [debug] ajp_service::jk_ajp_common.c (2449): processing worker1 with 2 retries [debug] ajp_send_request::jk_ajp_common.c (1623): (worker1) all endpoints are disconnected. [debug] jk_open_socket::jk_connect.c (485): socket TCP_NODELAY set to On [debug] jk_open_socket::jk_connect.c (609): trying to connect socket 560 to 0.0.0.0:0 [info] jk_open_socket::jk_connect.c (627): connect to 0.0.0.0:0 failed (errno=47) [info] ajp_connect_to_endpoint::jk_ajp_common.c (995): Failed opening socket to (0.0.0.0:0) (errno=47) Why does mod_jk try to connect to 0.0.0.0:0 and not to 127.0.0.1:8009??? Thank you for your help! Tobias

    Read the article

  • Firefox 4 refreshes all tabs although no internet connection exists

    - by Maxim
    I have a problem since I updated to Firefox 4. With Firefox 3.x I could start it without a internet connection and almost all of my open tabs were still loaded. With this I was able to read my open sites in the train where I have no internet connection. This does not work in Firefox 4. If I launch Firefox 4 I see all my open tabs but the content is not available. It seems that the new version tries to refresh all tabs on startup. Is there a possibility to disable this behaviour? Thanks in advance. Regards Maxim

    Read the article

  • FreeBSD 8.1 unstable network connection

    - by frankcheong
    I have three FreeBSD 8.1 running on three different hardware and therefore consist of different network adapter as well (bce, bge and igb). I found that the network connection is kind of unstable which I have tried to scp some 10MB file and found that I cannot always get the files completed successfully. I have further checked with my network admin and he claim that the problem is being caused by the network driver which cannot support the load whereby he tried to ping using huge packet size (around 15k) and my server will drop packet consistently at a regular interval. I found that this statement may not be valid since the three server is using three different network drive and it would be quite impossible that the same problem is being caused by three different network adapter and thus different network driver. Since then I have tried to tune up the performance by playing around with the /etc/sysctl.conf figures with no luck. kern.ipc.somaxconn=1024 kern.ipc.shmall=3276800 kern.ipc.shmmax=1638400000 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Required by pf net.inet.ip.forwarding=1 #Network Performance Tuning kern.ipc.maxsockbuf=16777216 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.recvbuf_max=16777216 # Setting specifically for 1 or even 10Gbps network net.local.stream.sendspace=262144 net.local.stream.recvspace=262144 net.inet.tcp.local_slowstart_flightsize=10 net.inet.tcp.nolocaltimewait=1 net.inet.tcp.mssdflt=1460 net.inet.tcp.sendbuf_auto=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.sendspace=262144 net.inet.tcp.recvspace=262144 net.inet.udp.recvspace=262144 kern.ipc.maxsockbuf=16777216 kern.ipc.nmbclusters=32768 net.inet.tcp.delayed_ack=1 net.inet.tcp.delacktime=100 net.inet.tcp.slowstart_flightsize=179 net.inet.tcp.inflight.enable=1 net.inet.tcp.inflight.min=6144 # Reduce the cache size of slow start connection net.inet.tcp.hostcache.expire=1 Our network admin also claim that they see quite a lot of network up and down from their cisco switch log while I cannot find any up down message inside the dmesg. Have further checked the netstat -s but dont have concrete idea. tcp: 133695291 packets sent 39408539 data packets (3358837321 bytes) 61868 data packets (89472844 bytes) retransmitted 24 data packets unnecessarily retransmitted 0 resends initiated by MTU discovery 50756141 ack-only packets (2148 delayed) 0 URG only packets 0 window probe packets 4372385 window update packets 39781869 control packets 134898031 packets received 72339403 acks (for 3357601899 bytes) 190712 duplicate acks 0 acks for unsent data 59339201 packets (3647021974 bytes) received in-sequence 114 completely duplicate packets (135202 bytes) 27 old duplicate packets 0 packets with some dup. data (0 bytes duped) 42090 out-of-order packets (60817889 bytes) 0 packets (0 bytes) of data after window 0 window probes 3953896 window update packets 64181 packets received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 45192 discarded due to memory problems 19945391 connection requests 1323420 connection accepts 0 bad connection attempts 0 listen queue overflows 0 ignored RSTs in the windows 21133581 connections established (including accepts) 21268724 connections closed (including 32737 drops) 207874 connections updated cached RTT on close 207874 connections updated cached RTT variance on close 132439 connections updated cached ssthresh on close 42392 embryonic connections dropped 72339338 segments updated rtt (of 69477829 attempts) 390871 retransmit timeouts 0 connections dropped by rexmit timeout 0 persist timeouts 0 connections dropped by persist timeout 0 Connections (fin_wait_2) dropped because of timeout 13990 keepalive timeouts 2 keepalive probes sent 13988 connections dropped by keepalive 173044 correct ACK header predictions 36947371 correct data packet header predictions 1323420 syncache entries added 0 retransmitted 0 dupsyn 0 dropped 1323420 completed 0 bucket overflow 0 cache overflow 0 reset 0 stale 0 aborted 0 badack 0 unreach 0 zone failures 1323420 cookies sent 0 cookies received 1864 SACK recovery episodes 18005 segment rexmits in SACK recovery episodes 26066896 byte rexmits in SACK recovery episodes 147327 SACK options (SACK blocks) received 87473 SACK options (SACK blocks) sent 0 SACK scoreboard overflow 0 packets with ECN CE bit set 0 packets with ECN ECT(0) bit set 0 packets with ECN ECT(1) bit set 0 successful ECN handshakes 0 times ECN reduced the congestion window udp: 5141258 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 1 with no checksum 0 dropped due to no socket 129616 broadcast/multicast datagrams undelivered 0 dropped due to full socket buffers 0 not for hashed pcb 5011642 delivered 5016050 datagrams output 0 times multicast source filter matched sctp: 0 input packets 0 datagrams 0 packets that had data 0 input SACK chunks 0 input DATA chunks 0 duplicate DATA chunks 0 input HB chunks 0 HB-ACK chunks 0 input ECNE chunks 0 input AUTH chunks 0 chunks missing AUTH 0 invalid HMAC ids received 0 invalid secret ids received 0 auth failed 0 fast path receives all one chunk 0 fast path multi-part data 0 output packets 0 output SACKs 0 output DATA chunks 0 retransmitted DATA chunks 0 fast retransmitted DATA chunks 0 FR's that happened more than once to same chunk 0 intput HB chunks 0 output ECNE chunks 0 output AUTH chunks 0 ip_output error counter Packet drop statistics: 0 from middle box 0 from end host 0 with data 0 non-data, non-endhost 0 non-endhost, bandwidth rep only 0 not enough for chunk header 0 not enough data to confirm 0 where process_chunk_drop said break 0 failed to find TSN 0 attempt reverse TSN lookup 0 e-host confirms zero-rwnd 0 midbox confirms no space 0 data did not match TSN 0 TSN's marked for Fast Retran Timeouts: 0 iterator timers fired 0 T3 data time outs 0 window probe (T3) timers fired 0 INIT timers fired 0 sack timers fired 0 shutdown timers fired 0 heartbeat timers fired 0 a cookie timeout fired 0 an endpoint changed its cookiesecret 0 PMTU timers fired 0 shutdown ack timers fired 0 shutdown guard timers fired 0 stream reset timers fired 0 early FR timers fired 0 an asconf timer fired 0 auto close timer fired 0 asoc free timers expired 0 inp free timers expired 0 packet shorter than header 0 checksum error 0 no endpoint for port 0 bad v-tag 0 bad SID 0 no memory 0 number of multiple FR in a RTT window 0 RFC813 allowed sending 0 RFC813 does not allow sending 0 times max burst prohibited sending 0 look ahead tells us no memory in interface 0 numbers of window probes sent 0 times an output error to clamp down on next user send 0 times sctp_senderrors were caused from a user 0 number of in data drops due to chunk limit reached 0 number of in data drops due to rwnd limit reached 0 times a ECN reduced the cwnd 0 used express lookup via vtag 0 collision in express lookup 0 times the sender ran dry of user data on primary 0 same for above 0 sacks the slow way 0 window update only sacks sent 0 sends with sinfo_flags !=0 0 unordered sends 0 sends with EOF flag set 0 sends with ABORT flag set 0 times protocol drain called 0 times we did a protocol drain 0 times recv was called with peek 0 cached chunks used 0 cached stream oq's used 0 unread messages abandonded by close 0 send burst avoidance, already max burst inflight to net 0 send cwnd full avoidance, already max burst inflight to net 0 number of map array over-runs via fwd-tsn's ip: 137814085 total packets received 0 bad header checksums 0 with size smaller than minimum 0 with data size < data length 0 with ip length > max ip packet size 0 with header length < data size 0 with data length < header length 0 with bad options 0 with incorrect version number 1200 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 300 packets reassembled ok 137813009 packets for this host 530 packets for unknown/unsupported protocol 0 packets forwarded (0 packets fast forwarded) 61 packets not forwardable 0 packets received for unknown multicast group 0 redirects sent 137234598 packets sent from this host 0 packets sent with fabricated ip header 685307 output packets dropped due to no bufs, etc. 52 output packets discarded due to no route 300 output datagrams fragmented 1200 fragments created 0 datagrams that can't be fragmented 0 tunneling packets that can't find gif 0 datagrams with bad address in header icmp: 0 calls to icmp_error 0 errors not generated in response to an icmp message Output histogram: echo reply: 305 0 messages with bad code fields 0 messages less than the minimum length 0 messages with bad checksum 0 messages with bad length 0 multicast echo requests ignored 0 multicast timestamp requests ignored Input histogram: destination unreachable: 530 echo: 305 305 message responses generated 0 invalid return addresses 0 no return routes ICMP address mask responses are disabled igmp: 0 messages received 0 messages received with too few bytes 0 messages received with wrong TTL 0 messages received with bad checksum 0 V1/V2 membership queries received 0 V3 membership queries received 0 membership queries received with invalid field(s) 0 general queries received 0 group queries received 0 group-source queries received 0 group-source queries dropped 0 membership reports received 0 membership reports received with invalid field(s) 0 membership reports received for groups to which we belong 0 V3 reports received without Router Alert 0 membership reports sent arp: 376748 ARP requests sent 3207 ARP replies sent 245245 ARP requests received 80845 ARP replies received 326090 ARP packets received 267712 total packets dropped due to no ARP entry 108876 ARP entrys timed out 0 Duplicate IPs seen ip6: 2226633 total packets received 0 with size smaller than minimum 0 with data size < data length 0 with bad options 0 with incorrect version number 0 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 0 fragments that exceeded limit 0 packets reassembled ok 2226633 packets for this host 0 packets forwarded 0 packets not forwardable 0 redirects sent 2226633 packets sent from this host 0 packets sent with fabricated ip header 0 output packets dropped due to no bufs, etc. 8 output packets discarded due to no route 0 output datagrams fragmented 0 fragments created 0 datagrams that can't be fragmented 0 packets that violated scope rules 0 multicast packets which we don't join Input histogram: UDP: 2226633 Mbuf statistics: 962679 one mbuf 1263954 one ext mbuf 0 two or more ext mbuf 0 packets whose headers are not continuous 0 tunneling packets that can't find gif 0 packets discarded because of too many headers 0 failures of source address selection Source addresses selection rule applied: icmp6: 0 calls to icmp6_error 0 errors not generated in response to an icmp6 message 0 errors not generated because of rate limitation 0 messages with bad code fields 0 messages < minimum length 0 bad checksums 0 messages with bad length Histogram of error messages to be generated: 0 no route 0 administratively prohibited 0 beyond scope 0 address unreachable 0 port unreachable 0 packet too big 0 time exceed transit 0 time exceed reassembly 0 erroneous header field 0 unrecognized next header 0 unrecognized option 0 redirect 0 unknown 0 message responses generated 0 messages with too many ND options 0 messages with bad ND options 0 bad neighbor solicitation messages 0 bad neighbor advertisement messages 0 bad router solicitation messages 0 bad router advertisement messages 0 bad redirect messages 0 path MTU changes rip6: 0 messages received 0 checksum calculations on inbound 0 messages with bad checksum 0 messages dropped due to no socket 0 multicast messages dropped due to no socket 0 messages dropped due to full socket buffers 0 delivered 0 datagrams output netstat -m 516/5124/5640 mbufs in use (current/cache/total) 512/1634/2146/32768 mbuf clusters in use (current/cache/total/max) 512/1536 mbuf+clusters out of packet secondary zone in use (current/cache) 0/1303/1303/12800 4k (page size) jumbo clusters in use (current/cache/total/max) 0/0/0/6400 9k jumbo clusters in use (current/cache/total/max) 0/0/0/3200 16k jumbo clusters in use (current/cache/total/max) 1153K/9761K/10914K bytes allocated to network (current/cache/total) 0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters) 0/0/0 requests for jumbo clusters denied (4k/9k/16k) 0/8/6656 sfbufs in use (current/peak/max) 0 requests for sfbufs denied 0 requests for sfbufs delayed 0 requests for I/O initiated by sendfile 0 calls to protocol drain routines Anyone got an idea what might be the possible cause?

    Read the article

  • Windows 2008 Server in Amazon EC2 stops responding when SSTP/VPN connection is closed

    - by user38349
    All, I have a single Windows 2008 server running in Amazon's EC2 cloud. It's running a web application that is running fine and is accessible to the outside world. I need 3-5 developers to be able to work on database on the server, and was intending to accomplish this by setting up SSTP/RRAS on the server and letting them VPN in. This has been a bit of an ordeal due to the amount of server roles and messing with certificates that has been needed, but my VPN connection works now (all clients will be Windows 7). My problem is that when I drop my VPN connection (from the client side) the server hangs. The only way that I've found to get it back is to reboot it from the Amazon management console. Thanks for any guidance. Duncan

    Read the article

  • How does Windows Remote Desktop Connection Work?

    - by Devoted
    How does Windows Remote Desktop connection work? An IP address is used to connect to the computer but....how can that IP be accessed from anywhere? If, for example, the IP address is 128.10.10.10, there MUST be another 128.10.10.10 somewhere else in the world. How does Remote Desktop know which one to connect to? Thanks so much EDIT: Thank you! Answers cleared this up quite a bit. But if my remote desktop connection suddenly stopped working and I didn't change anything, how do I even start to diagnose what may be the problem? I can remote connect to it from a LAN computer though...

    Read the article

  • scp through ssh gateway connection

    - by zidarsk8
    so my network layou is something like this (I don't have enough reputation to post images so here's the link) http://i.imgur.com/OaD4i.png now Alice has access to SSH gateway (just gateway from now on) with: ssh [email protected] and the authorized keys file on the gateway looks like this #/home/Alice/.ssh/authorized_keys command="ssh -t alice@web" ssh-rsa ABCD...E== alice@somehost so when Alice trys to connect to the Gateway with her private key, she actually gets connected to the Web server (the gateway pc can make a connection to the web server with a passwordless private key, so that stays transparent). The question 1) How can I set this up so that Alice will be able to scp things to web server too? 2) I know this makes a separete connection, but is there any way for this to work as a normal ssh so that even something like -R12345:localhost:22 would work?

    Read the article

  • How can you connect to a SQL Server not on your domain?

    - by scotty2012
    I have a test machine that's not allowed on our domain because we are testing corporately unsupported applications (SQL 2008 and Server 2008). I want to use management studio to connect to the SQL2008 server but can't get it working. I have authentication set to mixed-mode, I've checked 'allow remote connections to this server', but when I try to access it, I get the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 53) Since it says the provider is Named Pipes, I enabled Named Pipes on the server, but still no dice. I've tried connecting to the system name, the IP, the system name\instance and IP\instance, all to no avail. Is what I'm trying to do not possible? Edit: Well, through some basic troubleshooting, I've found that I can't ping the server from my client computer, but I can ping the client computer from the server? They are both plugged into the same switch, and are sitting next to each other. The windows firewall on the server is turned on, is there some specific settings I need to enable? DAH! So it was the firewall blocking me. How can I enable the firewall and still connect?

    Read the article

  • Mountain Lion fails to connect to Windows share after the connection is interrupted

    - by T Reddy
    I have a Windows 7 share that my Mountain Lion Macbook Pro connects to. The windows share is simply a user account. For whatever reason, when my connection gets interrupted, the mac will show a dialog stating as such and will ask me to ignore or disconnect. From this point forward, I cannot re-establish the connection from the mac to the windows share (even if I reboot the mac). I always have to reboot the windows machine in order for my mac to see the share again. My Windows share is my media center, so I'm not always able to reboot the machine because it is recording TV. Has anybody else encountered this problem and if so how is it resolved?

    Read the article

  • windows firewall and network location switch after establishing a vpn connection

    - by Konrads
    I am looking for a reasonable solution for network location switching after VPN connection is established for Windows 7. The scenario is as follows: For location public (employee plugging in his laptop in hotel, public wi-fi,etc) all inbound connections are restricted, only outbound VPN + www is enabled. Employee then initiates a VPN connection, VPN pushes routes to 10.0.0.0/8 subnet Now I would like to have lax security rules for traffic from/to 10.0.0.0/8 that comes through the VPN interface, while still protecting the laptop from traffic that comes via uplink interface as if it was private. How to achieve this switching and duality? One option I see is switching to IPSec...

    Read the article

  • Wireless connection switches off IP address

    - by Sanjay Gupta
    I have a Lenovo laptop with windows XP and a wireless connection at home. The wireless connection works when initially I switch on the computer. but if I leave it for even 5 minutes, the wireless is gone. Then I have to shut it off and start computer all over again, waiting for 5 minutes. Even if the wireless speed is 48Mbps or better, it gives the message "Renewing IP address" and gets stuck there not moving to the next stage. Other laptop in the household works fine and can be left on. Why does this happen ? I suspect that IP address is the problem and somehow is not registered in all the necessary files.

    Read the article

  • Ad-hoc connection between iPhone and Macbook Pro

    - by Phil Nash
    I sometimes find it useful to connect my iPhone to my Macbook Pro by creating an ad-hoc wireless network from the MBP and connecting to that from the iPhone. However, what I find is that sometimes this works and sometimes it doesn't. When it's not working the symptoms are usually that I see the ad-hoc SSID in the list of available networks on the iPhone, can connect to it from there (including entering my WEP key), and it shows up as the wifi network in use. However I don't get the wifi symbol in the taskbar (it remains as 3G) and attempting to use the connection (e.g. trying to connect to iTunes or Keynote using their respective Remote apps) fails saying that there is so wifi connection. I've tried rebooting both the iPhone and the MBP, recreating networks with different SSIDs and tried different channels - all to no avail! I'm especially puzzled that (a) sometimes it works just fine first time and (b) the Settings app seems to think its all connected fine. Is there anything else I should be trying?

    Read the article

  • Connection timed out exception, why?

    - by Dheeraj Kumar Aggarwal
    I am developing an application which uses embedded tomcat server 7, and deploys a web application on embedded server. My application accesses the embedded webapp through Rest APIs, but my clients are getting Connection Timed Out exceptions and port is also not blocked. I never gets this exception when I install this application on my local machine. Some points: IP address is used in the host name part (They are able to access this IP address on other port) Port is not blocked We are using Apache HttpClient library to access the URL Timeout interval seems not to be an issue. What are the possible reasons for this exception Connection Timed Out? or How can I simulate this problem on my local machine? Any pointers would be helpful.

    Read the article

  • LAN not picking up gigabit connection through patch panel

    - by user332555
    I have just purchased 2 FVS318G switches to install at my store. How this is set up is the server is in the back room. We have Cat 5E ran up through the ceiling and is patched into a panel in the back room. The 2 switches I just purchased are right next to the server in the back where all the cables patch in. I do a direct connection from the server to switch, avoiding the patch panel completely, and receive 1.0 gbps connection no problem. When i patch in the register computers from the front into the panel and then to the switch I am only getting 100 mbps on the registers up front. The patch panel does say Cat 5E on it but I am not sure if there is any interference in the line somewhere and I cannot get the full 1.0 gbps to the front registers like I want. Any ideas??

    Read the article

  • MySQL - allow connection from remote machine as root user

    - by Senthil Kumar
    Hi all, When I installed MySQL server in Windows, there was an option "Allow root connection from remote machine". I checked that option and I had no probs when using it. I installed MySQL server in Ubuntu 9.04 using apt-get install. I can connect to the sql server from the same machine but when I try to connect from a virtual machine, it doesn't work. My guess is that I should allow root connection from remote machine. How to do that?

    Read the article

  • How to go about scheduling a task in windows 7 to change wireless connection

    - by Skindeep2366
    This may or not be something that can be done. I cannot find anything on the wireless connection manager built into windows 7 let alone methods for passing params into it. Problem is as follows: I have 2 wireless routers. One provides internet access, the other provides sole access to the local network. Every day at 4am the main system creates a backup in 2 locations. One is a External usb drive, the other is a location on the network. This is all cool if it is remembered to change over to the local network router before leaving. But if it is forgotten the roof will collapse, the walls will burn, and I will be... well you get the idea. Solution: there is already a custom event that fires a automated backup program at 4am everyday. I need someway to force the wireless network to use the correct connection at say 3:58am everyday. Any ideas????

    Read the article

  • testing ssl cert for smtps => "secure connection could not be established with this website"

    - by cc young
    testing ssl cert on server using a web service. https, imaps and pop3s all check, but smtps yields the message "we advise you not to submit any confidential or personal data to this website because a secure connection could not be established with this website." running postfix tls logging: connect from s097.networking4all.com[213.249.64.242] lost connection after UNKNOWN from s097.networking4all.com[213.249.64.242] disconnect from s097.networking4all.com[213.249.64.242] these work correctly: telnet mydomain.net 587 openssl s_client -starttls smtp -crlf -connect mydomain.net:587 but cannot get email using ssl to log into either 587 or 564 - get same "UNKNOWN" problem. email smtp w/o ssh works fine. the test site is http://www.networking4all.com/en/support/tools/site+check/

    Read the article

  • Wireless very slow on one laptop on network, all other machines normal?

    - by th3dude19
    My new laptop (Acer Aspire Timeine 3810TZ running Windows 7 Home Premium 64bit) is acting very strange on my wireless network. Below are the issues I'm noticing... The connection frequently drops. I see the icon change from 'full bars' to 'empty bars with yellow star (meaning no connection)' occasionally. Almost every website I visit (Firefox) hangs for a long time on 'Looking up www.amazon.com' for example. After a long pause, it finally starts loading the website. Neither of these problems exist on any other machines on my network. I also have a desktop running the same OS wirelessly and it works fine. I've run several Speedtest.net tests and the speeds are great (20MBit down/4 up). Results from pingtest.net are as follows: Line quality: D Ping: 46ms Jitter: 65ms Packet Loss: 9% These results are to a server that is less than 10 miles from my residence. The results on the other machines in my house are normal. Any suggestions? This is becoming very annoying as I purchased this machine primarily for browsing.

    Read the article

  • Keep lan connection alive while going to sleep

    - by user18151
    Is it possible to keep lan connection alive when going to sleep? Although I would like a laptop independent(in general) answer, my laptop is Thinkpad T500 and the power manager shows in PCI options, the following three option regarding saving link state power: Off, moderate, maximum. Also instant resume apparently does something different, so that isn't much help either. I'm on Windows-7. Here's why: I'm a student, and currently I keep my laptop on almost all the time, but sometimes I sleep it and then I require to check something, so I turn it on. But then internet starts in at least a minute. So I avoid even putting it to sleep. I want that the internet connection should persist, so that I can put it to sleep to avoid power consumption.

    Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >