Search Results

Search found 7086 results on 284 pages for 'proprietary syntax'.

Page 69/284 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

• 12.04.1 no audio through HDMI

  - by JoJo

  having a bit of an issue with getting audio to go through HDMI. Here are the base specs: OS: Ubuntu Desktop 12.04.1 x64 CPU: AMD A10-5800K 3.8G 4M FM2 R Mobo: MSI FM2-A75MA-E35 OS: Ubuntu 12.04.1 LTS Vid Card: (integrated on CPU) AMD Radeon HD 7660D HDMI sound works fine under Win7 (after mobo and vid drivers are installed), so it's not physically broken. Audio through the normal headphone jacks works fine under Ubuntu. Looking at the audio panel, there is no HDMI output at all. aplay -l also reports only: card 0: Generic [HD-Audio Generic], device 0: ALC887-VD Analog [ALC887-VD Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 In additional drivers there are two versions: ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER (post-release update) The first installs, but problem persists. I do get more resolutions to pick from. Second version does not, reporting it failed installation and to find details at: /var/log/jockey.log Looked at the log, and it's insanely long, if necessary I can get it to you guys. Did more research and some had luck by manually installing the drivers, so tried to give that a shot by following this: https://help.ubuntu.com/community/BinaryDriverHowto/ATI#Manually_installing_Catalyst_12.6 starting at 3.1 Manually installing Catalyst 12.6. I immediately had 2 issues, (1) the AMD website does not provide any drivers for Linux, and (2) the following command did not work: sudo sh amd-driver-installer-12-6-x86.x86_64.run --buildpkg Ubuntu/precise sh: 0: Can't open amd-driver-installer-12-6-x86.x86_64.run Some other posts stated to update "alsa-drivers", but that also did not work as install command for the new version of them did not work. I forget the exact issue, but similar to above, cannot open / cannot find. Any help would be greatly appreciated!

  Read the article

• How does one escape the GPL?

  - by tehtros

  DISCLAIMER I don't pretend to know anything about licensing. In fact, everything I say below may be completely false! Backstory: Recently, I've been looking for a decent game engine, and I think I've found one that I really like, Cafu Engine. However, they have a dual licensing plan, where everything you make with the engine is forced under GPL, unless you pay for a commercial license. I'm not saying that it's a bad engine, they even say that they are very relaxed about the licensing fees. However, the fact that it even involves the GPL scares me. So my question is basicly, how does one escape the GPL. Here's an example: The id Tech engine, also known as the Quake engine, or the Doom engine, was the base for the popular Source engine. However, the id Tech engine has been released under the GPL, and the Source engine is proprietary. Did Valve get a different license? Or did they do something to escape the GPL? Is there a way to escape the GPL? Or, if you use GPL'd source code as a base for another project, are you forced to use the GPL, and make your source code available to the world. Could some random person take the id Tech engine, modify it past the point of recognition, then use it as a proprietary engine for commercial products? Or are they required to make it open source. One last thing, I generally have no problem what-so-ever with open source. However I feel that open source has it's place, but that is not in the bushiness world.

  Read the article

• When do domain concepts become application constructs?

  - by Noren

  I recently posted a question regarding recovering a DDD architecture that became an anemic domain model into a multitier architecture and this question is a follow-on of sorts. My question is when do domain concepts become application constructs. My application is a local client C# 4/WPF with the following architecture: Presentation Layer Views ViewModels Business Layer ??? Domain Layer Classes that take the POCOs with primitive types and create domain concepts (e.g. image, layer, etc) Sanity checks values (e.g. image width 0) Interfaces for DTOs Interface for a repository that abstracts the filesystem Data Access Layer Classes that parse the proprietary binary files into POCOs with primitive types by explicit knowledge of the file format Implementation of domain DTOs Implementation of domain repository class Local Filesystem Proprietary binary files When does the MyImageType domain class with Int32 width, height, and Int32[] pixels become a System.Windows.Media.ImageDrawing? If I put it in the domain layer, it seems like implemenation details are being leaked (what if I didn't want to use WPF?). If I put it in the presentation layer, it seems like it's doing too much. If I create a business layer, it seems like it would be doing too little since there are few "rules" given the CRUD nature of the application. I think all of my reading has lead to analysis paralysis, so I thought fresh eyes might lend some perspective.

  Read the article

• Radeon 9200 Driver?

  - by usuhh86

  I've been using Linux for a while, but haven't really done more than installed programs. I have Ubuntu 12.04 with an ATI Radeon 9200 graphics card. Ubuntu didn't recognize it during the install. All I want is a driver. Preferably the proprietary driver, but I'll settle for an open-source one if I need to. I went to the AMD support website, and whenever I click on the download link for "ATI Proprietary Linux x86 Display Driver 8.28.8" I get redirected to the main AMD website. I tried this on Firefox, Chrome, even booted up my netbook and tried it on IE9. Does anybody have a download link? And if not, a link to download an open-source alternative? Any help will be greatly appreciated. I'm pretty much still a newbie at this. OpenGL vendor string: Tungsten Graphics, Inc. OpenGL renderer string: Mesa DRI R200 (RV280 5961) x86/MMX/SSE2 TCL DRI2 OpenGL version string: 1.3 Mesa 8.0.2 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: no GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: no Unity 3D supported: no

  Read the article

• How do I get my graphic card to work properly?

  - by Lucas

  I been having some problems with my graphic card for a time now. But I had enough when I did'nt get Oil Rush to work on my HP Pavilion g6. The system has suggested hardware drivers for me, but the first time I installed them they pretty much fucked up the graphics. After some time I managed to get the computere to work properly (I thought) again. When the game did'nt work I tried to the hardware drivers for the graphic card anyway. First of all there was to possible choices insted of one, as the last time I installed the drivers (when it did'nt work out so good). The choices are: ATI/AMDs proprietary video drivers FGLRX (update for edition) and Proprietary FGLRX-video drivers for ATI/AMD I realized the drivers probebly are pretty much the same, so I tried the first one. But this did'nt work. Instead I was asked to "Look in to /usr/var/log/jockey.log". This did'nt helped me much. Instead I choiced the other one, wich was installed and after reboot there where some changes. First of all there was a lot more details for Unity that was'nt there before and some shortkeys are now working that did'nt before (like Ctrl + T and the Prt Sc-button). But overall everything doesn't work as it used to. Like when you browse between the workspaces it doesn't look the same. To get to the point: it doesn't work well right now even if I got some things better and now will not Oil Rush (as I mentioned in the beginning) even start. SO! Can someone give me any advice with this? I'm stuck. Can't manage to see whats wrong right now. Any help? My graphic card is AMD Radeon HD 6470M.

  Read the article

• VLC Ati Radeon 6870 Ubuntu 12.04 image skewed flicker

  - by Aaron

  I'm running Ubuntu 12.04 with ATI Radeon 6870 connected to my 40' Sharp TV. The video image is slightly jigged, like breaking a bit and slightly delayed. It just isn't smooth. The computer is very fast, like i7 with 12gb ram. I tried to run the same video with my mac laptop and on the tv with the same connection cable and it was running smoothly. i tried changing the video output in VLC to x11, increase caching, h264 skip loop filter to all, increase monitor refresh rate although it's already at 60 and it's an LCD tv. this is my xorg.conf : Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[3]-0" 0 0 EndSection Section "Module" Load "glx" EndSection Section "Monitor" Identifier "0-DFP9" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" Option "PreferredMode" "1920x1080" EndSection Section "Monitor" Identifier "0-DFP10" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1280x1024" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Device" Identifier "amdcccle-Device[3]-0" Driver "fglrx" Option "Monitor-DFP9" "0-DFP9" BusID "PCI:3:0:0" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 EndSection Section "Screen" Identifier "amdcccle-Screen[3]-0" Device "amdcccle-Device[3]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• 12.04 disabling wireless via dbus does not work

  - by FlabbergastedPickle

  I am using a proprietary rt3652sta driver for my wireless card. It appears as a ra0 device on the 64-bit Ubuntu 12.04. According to the online documentation the following used to work definitely up to 10.04. dbus-send --system --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.DBus.Properties.Set string:org.freedesktop.NetworkManager string:WirelessEnabled variant:boolean:false This however has no effect on the aforesaid wireless card in 12.04. Also, rfkill does not work as it does not even list the wireless button (again, likely due to the wireless driver being proprietary): rfkill list It only lists the hci0 (bluetooth) one and one can block/unblock it accordingly but this has no effect on the wifi. ifup/down also does not work (AFAICT)... And this leaves me with disabling wireless through the network manager applet. However, trying to do so via dbus appears not to work and yet I would like to automate it via a script. Any ideas how I could find out the proper dbus structure for the call? Is this even possible in Ubuntu 12.04?

  Read the article

• How to keep background requests in sequence

  - by Jason Lewis

  I'm faced with implementing interfaces for some rather archaic systems, for handling online deposits to stored value accounts (think campus card accounts for students). Here's my dilemma: stage 1 of the process involves passing the user off to a thrid-party site for the credit card transaction, like old-school PayPal. Step two involves using a proprietary protocol for communicating with a legacy system for conducting the actual deposit. Step two requires that each transaction have a unique sequence number, and that the requests' seqnums are in order. Since we're logging each transaction in Postgres, my first thought was to take a number from a sequence in the DB, guaranteeing uniqueness. But since we're dealing with web requests that might come in near-simultaneously, and since latency with the return from the off-ste payment processor is beyond our control, there's always the chance for a race condition in the order of requests passed back to the proprietary system, and if the seqnums are out of order, the request fails silently (brilliant, right?). I thought about enqueuing the requests in Redis and using Resque workers to process them (single worker, single process, so they are processed in order), but we need to be able to give the user feedback as to whether the transaction was processed successfully, so this seems less feasible to me. I've tried to make this application handle concurrency well (as much as possible for a Ruby on Rails app), but now we're in a situation where we have to interact with a system that is designed to be single process, single threaded, and sequential. If it at least gave an "out of order" error, I could just increment (or take the next value off the sequence), but it's designed to fail silently in the event of ANY error. We are handling timeouts in a way that blocks on I/O, but since the application uses multiple workers (Unicorn), that's no guarantee. Any ideas/suggestions would be appreciated.

  Read the article

• ATI Radeon 5800 series dual monitor unity not 3D accelerated

  - by Victor S

  When I had a single monitor setup, without Xinerama, with my current setup of Ubuntu 11.10, ATI 5800 series card, Unity showed transparencies, shadows, etc. (although graphics was reported as 'Standard' in the control/settings panel). Having switched to a dual monitor setup, dell 24" UltraSharp and a smaller Acer monitor, Unity shows only as 2d, even though I'm not loggin in to that display manager. WebGL performance is very sluggish, I'm getting the impression that the processor is doing all the work and the card isn't even accessible even though the drivers are installed (from the ubuntu repository, I did not compile custom drivers). Any tips on how to enable full 3D accelerationn and video card support. Here is my xorg.conf file: Section "Monitor" Identifier "0-DFP3" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1680x1050" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "0-DFP4" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1920x1200" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 SubSection "Display" EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[1]-0" Device "amdcccle-Device[1]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "amdcccle-Screen[1]-1" Device "amdcccle-Device[1]-1" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Module" Load "glx" EndSection Section "ServerLayout" Identifier "amdcccle Layout" Screen 0 "amdcccle-Screen[1]-0" 0 0 Screen "amdcccle-Screen[1]-1" 1920 0 EndSection Section "Device" Identifier "amdcccle-Device[1]-0" Driver "fglrx" Option "Monitor-DFP4" "0-DFP4" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "amdcccle-Device[1]-1" Driver "fglrx" Option "Monitor-DFP3" "0-DFP3" BusID "PCI:1:0:0" Screen 1 EndSection Section "ServerFlags" Option "Xinerama" "on" EndSection More info: fglrxinfo display: :0 screen: 0 OpenGL vendor string: ATI Technologies Inc. OpenGL renderer string: ATI Radeon HD 5800 Series OpenGL version string: 4.1.11005 Compatibility Profile Context

  Read the article

• How should we deal with multiple transaction-report requests?

  - by Mithir

  We are developing a system for the retail market which one of it's features will enable clients(actually consumer clubs) to go through all transactions made by end-clients. One of the ways to get this information will be via an API. The idea is that there will be requests for reports with a start date and an end date, and a response will have all the transactions between those dates. We are worry that some reports may be very large, and that some clients will repeatedly request for reports, in this case the DB and CPU will be very overloaded. The same server that will service those requests, also takes care the the actual retail transactions (received by proprietary devices) and a Web application. We are not sure about how to limit the report requests from the API so that it won't affect the system too much. So, how should we deal with this scenario? any thoughts? EDIT: just to make clear: When I mentioned proprietary devices I meant "On-Location" devices which are used during sales with end-clients, this means that these requests shouldn't get delayed, and this is the main concern.

  Read the article

• How successful is GPL in reaching its goals?

  - by StasM

  There are, broadly, two types of FOSS licenses when it relates to commercial usage of the code - let's say the GPL-type and the BSD-type. The first is, broadly, restrictive about commercial usage (by usage I also mean modification and redistribution, as well as creating derived works, etc.) of the code under the license, and the second is much more permissive. As I understand, the idea behind GPL-type licenses is to encourage people to abandon the proprietary software model and instead convert to the FOSS code, and the license is the instrument to entice them to do so - i.e. "you can use this nice software, but only if you agree to come to our camp and play by our rules". What I want to ask is - was this strategy successful so far? I.e. are there any major achievements in the form of some big project going from closed to open because of GPL or some software being developed in the open only because GPL made it so? How big is the impact of this strategy - compared, say, to the world where everybody would have BSD-type licenses or release all open-source code under public domain? Note that I am not asking if FOSS model is successful - this is beyond question. What I am asking is if the specific way of enticing people to convert from proprietary to FOSS used by GPL-type and not used by BSD-type licenses was successful. I also don't ask about the merits of GPL itself as the license - just about the fact of its effectiveness.

  Read the article

• How do I get 1366x768 resolution on 12.04?

  - by Megan

  I am on an HP Envy 14, and the proper resolution that I should be using is 1366x768. This is not an option and I am stuck on 1024x768. I am using Linux 12.04. lspci | grep VGA: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Madison [Radeon HD 5000M Series] I've tried to add the resolution as a mode in xorg.conf but that does not work. Please any help would be appreciated. I'm new to Linux and just got my dual boot working but this resolution issue is killing me. Edit1 I just tried using the xrandr command: xrandr --newmode "1368x768_60.00" 85.25 1368 1440 1576 1784 768 771 781 798 -hsync +vsync But I get an error: xrandr: Failed to get size of gamma for output default Edit2 lsmod returns the following: Module Size Used by vesafb 13844 1 rfcomm 47604 12 bnep 18281 2 parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 arc4 12529 2 joydev 17693 0 hid_logitech_dj 18594 0 i915 472941 5 uvcvideo 72627 0 usbhid 47199 1 hid_logitech_dj hid 99559 2 hid_logitech_dj,usbhid psmouse 87692 0 iwlwifi 332525 0 mac80211 506816 1 iwlwifi videodev 98259 1 uvcvideo snd_hda_codec_idt 70795 1 mei 41616 0 btusb 18288 2 v4l2_compat_ioctl32 17128 1 videodev hp_accel 25976 0 lis3lv02d 19876 1 hp_accel hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi input_polldev 13896 1 lis3lv02d drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 serio_raw 13211 0 snd_hda_intel 33773 5 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec bluetooth 180104 23 rfcomm,bnep,btusb cfg80211 205544 2 iwlwifi,mac80211 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec mac_hid 13253 0 snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_ra wmidi,snd_seq,snd_timer,snd_seq_device wmi 19256 1 hp_wmi video 19596 1 i915 intel_ips 18174 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 I have installed ATI/AMD proprietary FGLRX graphics driver. But there is another one called ATI/AMD proprietary FGLRX graphics driver (post-release updates) which I have trouble installing because it gives me an error and tells me to look at some sort of jockey log.

  Read the article

• Second Monitor Detected, but not receiving a signal after upgrading to 12.04

  - by user62458

  After I upgraded to 12.04, my second monitor is detected (in display settings), but will not power on. I have scoured the Internet and forums for a solution and I can't find anything. I have found a couple people with the same problem, but never a solution for it. I am no expert, but I'm certainly not a noob. My computer uses AMD Radeon 6250 graphics, but I do NOT want to use the proprietary graphics drivers. They refuse to work properly with my second monitor (they ATI drivers will only mirror screens, and I've done everything to try to fix it, and I DON't want mirrored screens) Not to mention that the default open-source video drivers seem to work much better than the proprietary anyway! Again, Ubuntu's default video drivers work fine, and they even DETECT the second monitor (Dell 19'). I can drag stuff off the screen and put it on the 'space' of the second monitor and even a screen-shot shows that there are two monitors active; but the monitor is OFF. It will not power on. It goes into 'power-save' mode because it is not receiving a signal. For some reason it is not getting the signal to power on, even though Ubuntu thinks the monitor is working properly. I had this working fine on my Sony VAIO yesterday (with Radeon graphics/default Ubuntu video drivers). I upgraded to a Samsung Series 3 and now I have this issue. I can't for the life of me figure out why the monitor is connected, detected and I have screen space for the monitor, but the screen won't turn on! XRANDR Output: Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 VGA-0 connected (normal left inverted right x axis y axis) 1440x900 59.9 + 75.0 1280x1024 75.0 60.0 1152x864 75.0 1024x768 75.1 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 LVDS connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 194mm 1366x768 60.1*+ 1280x720 59.9 1152x768 59.8 1024x768 59.9 800x600 59.9 848x480 59.7 720x480 59.7 640x480 59.4 HDMI-0 disconnected (normal left inverted right x axis y axis)

  Read the article

• Dim (NEARLY blank) laptop screen, secondary screen works - why?

  - by LIttle Ancient Forest Kami

  My laptop screen is (almost) black while my secondary screen is fine. I believe it to be backlight / brightness related. Problem description it starts when I start the laptop system loads and works fine, just screen has problems I can see the screen though very faintly / dimly - it's hard to see anything which ain't very white e.g. starting screen has big Thinkpad logo in white, large font - I can see it, though very dimly second screen works very well Official backligtht debugging: using acpi setting as prescribed there for Thinkpads didn't help I can see an entry in /sys/class/backlight/ and it changes when I press hotkeys for brightness (current backlight power for instance goes up or down) acpi-off didn't helpm neither did acpi_backlight=vendor Hardware data Laptop is Thinkpad Edge with glossy screen. 4 processors, 2 cores, exemplary CPU data from cat /proc/cpuinfo reports Genuine Intel i5 (M 480 @ 2.67GHz). OS is Ubuntu Lucid, 10.04 LTS, 64-bit, with Linux generic kernel (2.6.32-44) and GNOME 2.32.2 (though I doubt there lies the problem). $ lspci | grep VGA 01:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series] $ lshw -C display *-display description: VGA compatible controller product: M92 [Mobility Radeon HD 4500 Series] vendor: ATI Technologies Inc physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:33 memory:c0000000-dfffffff(prefetchable) ioport:2000(size=256) memory:f0300000-f030ffff memory:f0320000-f033ffff(prefetchable) Driver I was NOT running any proprietary drivers, just checked with "Hardware drivers". There is one for ATI that is suggested there, though I didn't need it so far. UPDATE: changing the driver to proprietary one (ATI/AMD FGLRX) didn't help. Tried and failed Resetting / running on power or battery / charging / getting rid of static electricity / warming up *doesn't help* This is NOT a blank-screen problem, at least it isn't following official Ubuntu black-screen diagnostics - I can see my screen, though barely. What I will try next: - check last updates I've made - IIRC I am running on nomodeset already, but will verify this Any ideas how to proceed best? What is most probable cause?

  Read the article

• Solutions for cheaply replacing poorly-supported onboard ATI card with discreet graphics on desktop machine?

  - by echo-flow

  I have put Ubuntu on my mum's desktop computer. Unfortunately, the open source radeon driver does not work well with the onboard ATI graphics, and ATI's proprietary driver no longer supports the hardware at all. In order to use the ATI proprietary driver with this hardware, it is necessary to use an older version of Xorg, which is now only available in versions of Ubuntu older than 8.10. Unfortunately, the open source radeon driver seems to be causing X to lock up intermittently when my mum uses Audacity. I'm willing to accept that some hardware is not well-supported on Ubuntu, and so, because this is a desktop computer with a couple of free PCI slots, I think a better solution might simply be to plug in a new graphics card that might have better driver support, and to disable the onboard ATI card in the BIOS. The requirements for this card are that it be inexpensive and have robust (preferably open source) driver support in Ubuntu 10.04. Heavy-duty graphics processing power is not a requirement. A second-hand card on Ebay would also be fine. Can anyone make some recommendations?

  Read the article

• How do I get a Dell Latitude e6420 working?

  - by David_G

  I've just installed Ubuntu 12.04 (64-bit) on a brand new Dell Latitude e6420, and I'm having a few problems. This laptop has an Optimus (?) setup - i.e. integrated gfx and an Nvidia Quadro NVS 4200M. First problem - I ran setup, etc, and discovered that I can only run unity2d - If I try and login with unity3d, it just defaults to 2d. This is with nvidia-current installed (302.07). Note also that I can't run nvidia-settings ("You do not appear to be using the NVIDIA X driver."), and there is no additional drivers found ("No proprietary drivers are in use on this system"). I tried to troubleshoot this, and removed nvidia, leaving (I guess) just Nouveau drivers - In that case, unity3d did work, but I was stuck with the open source Nouveau drivers powering the integrated graphics. So, obviously, I want to run unity3d, and be using the more powerful Nvidia graphics card. I've tried a bit of tinkering around, but I'm not sure the best way to proceed, or perhaps more importantly, I'm not sure of what the best final solution might be. I've heard about bumblebee - but frankly, I would prefer to have the proprietary Nvidia drivers working properly. Any help would be much appreciated!

  Read the article

• How do I stop video tearing? (Nvidia prop driver, non-compositing window manager)

  - by Chan-Ho Suh

  I have that problem which seemingly afflicts many using the proprietary Nvidia driver: Video tearing: fine horizontal lines (usually near the top of my display) when there is a lot of panning or action in the video. (Note: switching back to the default nouveau driver is not an option, as its seemingly nonexistent power-management drains my battery several times faster) I've tried Totem, Parole, and VLC, and tearing occurs with all of them. The best result has been to use X11 output in VLC, but there is still tearing with relatively moderate action. Hardware: MacBook Air 3,2 -- which has an Nvidia GeForce 320M. There are two common fixes for tearing with Nvidia prop drivers: Turn off compositing, since Nvidia proprietary drivers don't usually play nice with compositing window managers on Linux (Compiz is an exception I'm aware of). But I use an extremely lightweight window manager (Awesome window manager) which is not even capable of compositing (or any cool effects). I also have this problem in Xfce, where I have compositing disabled. Enabling sync to VBlank. To enable this, I set the option in nvidia-settings and then autostart it as nvidia-settings -l with my other autostart programs. This seems to work, because when I run glxgears, I get: $ glxgears Running synchronized to the vertical refresh. The framerate should be approximately the same as the monitor refresh rate. 303 frames in 5.0 seconds = 60.500 FPS 300 frames in 5.0 seconds = 59.992 FPS And when I check the refresh rate using nvidia-settings: $ nvidia-settings -q RefreshRate Attribute 'RefreshRate' (wampum:0.0; display device: DFP-2): 60.00 Hz. All this suggests sync to VBlank is enabled. As I understand it, this is precisely designed to stop tearing, and a lot of people's problem is even getting something like glxgears to output the correct info. I don't understand why it's not working for me. xorg.conf: http://paste.ubuntu.com/992056/ Example of observed tearing::

  Read the article

• Dual displays not working - NVidia - Ubuntu 12.04 - Second Monitor - Two Screens

  - by user75105

  Graphics Card: NVidia 460 GTX. Driver: NVIDIA accelerated graphics driver (version current) I have one DVI monitor, an old Dell LCD from 2005, and one VGA monitor, an Asus ML238H from 2010 whose HDMI port broke. The Asus is plugged into my graphics card's primary monitor slot and is the better monitor even though it is VGA but my computer defaults to the Dell. This happens when I boot as well; the loading screens, the motherboard brand image, etc. are all displayed on the Dell monitor until Windows loads. Then both monitors work. The same thing happened when I booted up Ubuntu 12.04 but I did not see the second monitor when the log-in screen popped up, nor did I when I logged in. I went to System Settings/Displays and my Asus monitor is not an option. I clicked Detect Displays and the Asus is not detected. I looked at the other questions regarding NVIDIA drivers and recalled my problems with Ubuntu a few years ago and decided to check the driver. I went to Additional Drivers to install the proprietary driver and it looks like it's installed and active but I'm still having this problem. There is another driver option, the post-release NVIDIA driver, but that does not fix the problem either. Also, under System Details/Graphics the graphics device is listed as Unknown, which might indicate that it is using an open source generic driver and not the proprietary NVidia driver. But under Additional Drivers it says that I am using the NVidia driver. Any help is appreciated.

  Read the article

• Dual displays not working - NVidia - Ubuntu 12.4

  - by user75105

  Graphics Card: NVidia 460 GTX. Driver: NVIDIA accelerated graphics driver (version current) I have one DVI monitor, an old Dell LCD from 2005, and one VGA monitor, an Asus ML238H from 2010 whose HDMI port broke. The Asus is plugged into my graphics card's primary monitor slot and is the better monitor even though it is VGA but my computer defaults to the Dell. This happens when I boot as well; the loading screens, the motherboard brand image, etc. are all displayed on the Dell monitor until Windows loads. Then both monitors work. The same thing happened when I booted up Ubuntu 12.4 but I did not see the second monitor when the log-in screen popped up, nor did I when I logged in. I went to System Settings/Displays and my Asus monitor is not an option. I clicked Detect Displays and the Asus is not detected. I looked at the other questions regarding NVIDIA drivers and recalled my problems with Ubuntu a few years ago and decided to check the driver. I went to Additional Drivers to install the proprietary driver and it looks like it's installed and active but I'm still having this problem. There is another driver option, the post-release NVIDIA driver, but that does not fix the problem either. Also, under System Details/Graphics the graphics device is listed as Unknown, which might indicate that it is using an open source generic driver and not the proprietary NVidia driver. But under Additional Drivers it says that I am using the NVidia driver. Any help is appreciated.

  Read the article

• One sentence descriptions of the various common software licenses?

  - by Rich

  Instead of having to read entire documentation and sift through all the legalese, can someone outline the more common licenses in language that is short and sweet and gets right to the point? Specifically, I'm using a 3rd party control that uses the Apache 2.0 license. My intention is to use this in a proprietary application that I am building for a corporation's use (not resold, but I'm being paid for my work). Does this mean I can or cannot use this control? Does it mean that I must maintain copyright/license information in my code? Does it mean that I must mention copyright/license information in a clearly visible location in the app? EDIT In response to an answer below with a link to an article by Jeff Atwood, the Apache license is described as follows: Apache License Open Permissive 9 Requires derivative works to provide notification of any licensed or proprietary code in a common location. Does this notification need to be in a "common location" in my source code or a common location visible within the app? What if this were a non GUI app (I'm assuming that could very well be my answer)? Thanks for the responses!!!

  Read the article

• Upgraded to Ubuntu 13.10 - Apache not able to start

  - by 0R10N

  I updated to Ubuntu 13.10 (from Ubuntu 13.04) last weekend, and now Apache is not being able to start. It was working perfectly well until the upgraded, and I haven't changed anything myself. When I ran a restart this is what I get apache2: Syntax error on line 260 of /etc/apache2/apache2.conf: Could not open configuration file /etc/apache2/conf.d/: No such file or directory So, I created the directory, and then I get this: * Starting web server apache2 * * The apache2 configtest failed. Output of config test was: [Wed Oct 30 11:17:42.921934 2013] [proxy_html:notice] [pid 2496] AH01425: I18n support in mod_proxy_html requires mod_xml2enc. Without it, non-ASCII characters in proxied pages are likely to display incorrectly. AH00526: Syntax error on line 84 of /etc/apache2/apache2.conf: Invalid command 'LockFile', perhaps misspelled or defined by a module not included in the server configuration Action 'configtest' failed. The Apache error log may have more information. Thanks!

  Read the article

• May 20th Links: ASP.NET MVC, ASP.NET, .NET 4, VS 2010, Silverlight

  - by ScottGu

  Here is the latest in my link-listing series.  Also check out my VS 2010 and .NET 4 series and ASP.NET MVC 2 series for other on-going blog series I’m working on. [In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu] ASP.NET MVC How to Localize an ASP.NET MVC Application: Michael Ceranski has a good blog post that describes how to localize ASP.NET MVC 2 applications. ASP.NET MVC with jTemplates Part 1 and Part 2: Steve Gentile has a nice two-part set of blog posts that demonstrate how to use the jTemplate and DataTable jQuery libraries to implement client-side data binding with ASP.NET MVC. CascadingDropDown jQuery Plugin for ASP.NET MVC: Raj Kaimal has a nice blog post that demonstrates how to implement a dynamically constructed cascading dropdownlist on the client using jQuery and ASP.NET MVC. How to Configure VS 2010 Code Coverage for ASP.NET MVC Unit Tests: Visual Studio enables you to calculate the “code coverage” of your unit tests.  This measures the percentage of code within your application that is exercised by your tests – and can give you a sense of how much test coverage you have.  Gunnar Peipman demonstrates how to configure this for ASP.NET MVC projects. Shrinkr URL Shortening Service Sample: A nice open source application and code sample built by Kazi Manzur that demonstrates how to implement a URL Shortening Services (like bit.ly) using ASP.NET MVC 2 and EF4.  More details here. Creating RSS Feeds in ASP.NET MVC: Damien Guard has a nice post that describes a cool new “FeedResult” class he created that makes it easy to publish and expose RSS feeds from within ASP.NET MVC sites. NoSQL with MongoDB, NoRM and ASP.NET MVC Part 1 and Part 2: Nice two-part blog series by Shiju Varghese on how to use MongoDB (a document database) with ASP.NET MVC.  If you are interested in document databases also make sure to check out the Raven DB project from Ayende. Using the FCKEditor with ASP.NET MVC: Quick blog post that describes how to use FCKEditor – an open source HTML Text Editor – with ASP.NET MVC. ASP.NET Replace Html.Encode Calls with the New HTML Encoding Syntax: Phil Haack has a good blog post that describes a useful way to quickly update your ASP.NET pages and ASP.NET MVC views to use the new <%: %> encoding syntax in ASP.NET 4.  I blogged about the new <%: %> syntax – it provides an easy and concise way to HTML encode content. Integrating Twitter into an ASP.NET Website using OAuth: Scott Mitchell has a nice article that describes how to take advantage of Twiter within an ASP.NET Website using the OAuth protocol – which is a simple, secure protocol for granting API access. Creating an ASP.NET report using VS 2010 Part 1, Part 2, and Part 3: Raj Kaimal has a nice three part set of blog posts that detail how to use SQL Server Reporting Services, ASP.NET 4 and VS 2010 to create a dynamic reporting solution. Three Hidden Extensibility Gems in ASP.NET 4: Phil Haack blogs about three obscure but useful extensibility points enabled with ASP.NET 4. .NET 4 Entity Framework 4 Video Series: Julie Lerman has a nice, free, 7-part video series on MSDN that walks through how to use the new EF4 capabilities with VS 2010 and .NET 4.  I’ll be covering EF4 in a blog series that I’m going to start shortly as well. Getting Lazy with System.Lazy: System.Lazy and System.Lazy<T> are new features in .NET 4 that provide a way to create objects that may need to perform time consuming operations and defer the execution of the operation until it is needed.  Derik Whittaker has a nice write-up that describes how to use it. LINQ to Twitter: Nifty open source library on Codeplex that enables you to use LINQ syntax to query Twitter. Visual Studio 2010 Using Intellitrace in VS 2010: Chris Koenig has a nice 10 minute video that demonstrates how to use the new Intellitrace features of VS 2010 to enable DVR playback of your debug sessions. Make the VS 2010 IDE Colors look like VS 2008: Scott Hanselman has a nice blog post that covers the Visual Studio Color Theme Editor extension – which allows you to customize the VS 2010 IDE however you want. How to understand your code using Dependency Graphs, Sequence Diagrams, and the Architecture Explorer: Jennifer Marsman has a nice blog post describes how to take advantage of some of the new architecture features within VS 2010 to quickly analyze applications and legacy code-bases. How to maintain control of your code using Layer Diagrams: Another great blog post by Jennifer Marsman that demonstrates how to setup a “layer diagram” within VS 2010 to enforce clean layering within your applications.  This enables you to enforce a compiler error if someone inadvertently violates a layer design rule. Collapse Selection in Solution Explorer Extension: Useful VS 2010 extension that enables you to quickly collapse “child nodes” within the Visual Studio Solution Explorer.  If you have deeply nested project structures this extension is useful. Silverlight and Windows Phone 7 Building a Simple Windows Phone 7 Application: A nice tutorial blog post that demonstrates how to take advantage of Expression Blend to create an animated Windows Phone 7 application. If you haven’t checked out my Windows Phone 7 Twitter Tutorial I also recommend reading that. Hope this helps, Scott P.S. If you haven’t already, check out this month’s "Find a Hoster” page on the www.asp.net website to learn about great (and very inexpensive) ASP.NET hosting offers.

  Read the article

• ASP.NET MVC 3 Hosting :: ASP.NET MVC 3 First Look

  - by mbridge

  MVC 3 View Enhancements MVC 3 introduces two improvements to the MVC view engine: - Ability to select the view engine to use. MVC 3 allows you to select from any of your  installed view engines from Visual Studio by selecting Add > View (including the newly introduced ASP.NET “Razor” engine”): - Support for the next ASP.NET “Razor” syntax. The newly previewed Razor syntax is a concise lightweight syntax. MVC 3 Control Enhancements - Global Filters: ASP.NET MVC 3  allows you to specify that a filter which applies globally to all Controllers within an app by adding it to the GlobalFilters collection.  The RegisterGlobalFilters() method is now included in the default Global.asax class template and so provides a convenient place to do this since is will then be called by the Application_Start() method: void RegisterGlobalFilters(GlobalFilterCollection filters) { filters.Add(new HandleLoggingAttribute()); filters.Add(new HandleErrorAttribute()); } void Application_Start() { RegisterGlobalFilters (GlobalFilters.Filters); } - Dynamic ViewModel Property : MVC 3 augments the ViewData API with a new “ViewModel” property on Controller which is of type “dynamic” – and therefore enables you to use the new dynamic language support in C# and VB pass ViewData items using a cleaner syntax than the current dictionary API. Public ActionResult Index() { ViewModel.Message = "Hello World"; return View(); } - New ActionResult Types : MVC 3 includes three new ActionResult types and helper methods: 1. HttpNotFoundResult – indicates that a resource which was requested by the current URL was not found. HttpNotFoundResult will return a 404 HTTP status code to the calling client. 2. PermanentRedirects – The HttpRedirectResult class contains a new Boolean “Permanent” property which is used to indicate that a permanent redirect should be done. Permanent redirects use a HTTP 301 status code.  The Controller class  includes three new methods for performing these permanent redirects: RedirectPermanent(), RedirectToRoutePermanent(), andRedirectToActionPermanent(). All  of these methods will return an instance of the HttpRedirectResult object with the Permanent property set to true. 3. HttpStatusCodeResult – used for setting an explicit response status code and its associated description. MVC 3 AJAX and JavaScript Enhancements MVC 3 ships with built-in JSON binding support which enables action methods to receive JSON-encoded data and then model-bind it to action method parameters. For example a jQuery client-side JavaScript could define a “save” event handler which will be invoked when the save button is clicked on the client. The code in the event handler then constructs a client-side JavaScript “product” object with 3 fields with their values retrieved from HTML input elements. Finally, it uses jQuery’s .ajax() method to POST a JSON based request which contains the product to a /theStore/UpdateProduct URL on the server: $('#save').click(function () { var product = { ProdName: $('#Name').val() Price: $('#Price').val(), } $.ajax({ url: '/theStore/UpdateProduct', type: "POST"; data: JSON.stringify(widget), datatype: "json", contentType: "application/json; charset=utf-8", success: function () { $('#message').html('Saved').fadeIn(), }, error: function () { $('#message').html('Error').fadeIn(), } }); return false; }); MVC will allow you to implement the /theStore/UpdateProduct URL on the server by using an action method as below. The UpdateProduct() action method will accept a strongly-typed Product object for a parameter. MVC 3 can now automatically bind an incoming JSON post value to the .NET Product type on the server without having to write any custom binding. [HttpPost] public ActionResult UpdateProduct(Product product) { // save logic here return null } MVC 3 Model Validation Enhancements MVC 3 builds on the MVC 2 model validation improvements by adding   support for several of the new validation features within the System.ComponentModel.DataAnnotations namespace in .NET 4.0: - Support for the new DataAnnotations metadata attributes like DisplayAttribute. - Support for the improvements made to the ValidationAttribute class which now supports a new IsValid overload that provides more info on  the current validation context, like what object is being validated. - Support for the new IValidatableObject interface which enables you to perform model-level validation and also provide validation error messages which are specific to the state of the overall model. MVC 3 Dependency Injection Enhancements MVC 3 includes better support for applying Dependency Injection (DI) and also integrating with Dependency Injection/IOC containers. Currently MVC 3 Preview 1 has support for DI in the below places: - Controllers (registering & injecting controller factories and injecting controllers) - Views (registering & injecting view engines, also for injecting dependencies into view pages) - Action Filters (locating and  injecting filters) And this is another important blog about Microsoft .NET and technology: - Windows 2008 Blog - SharePoint 2010 Blog - .NET 4 Blog And you can visit here if you're looking for ASP.NET MVC 3 hosting

  Read the article

• Programming languages, positional languages and natural languages

  - by Vitalij Zadneprovskij

  Some programming languages are modeled on machine code, like assembly languages. Other languages are modeled on a natural language, the English language. Others are not modeled on either machine code or natural language. Languages such as PROLOG, for example, don't follow either model. I came across this Perl module Lingua::Romana::Perligata, that allows to write programs using a syntax that is very similar to Latin. Are there programming languages that have less positional syntax? Are there other languages or modules that allow you to write in syntaxes inspired by other natural languages, like French, Hebrew or Farsi? There is a very long list on Wikipedia, but most of those projects are dead. There is a related question on StackOverflow. The answer that was accepted is "Use Google".

  Read the article

• VBoxManage modifyhd --resize doesn't exist?

  - by George Korac

  I'm trying to increase the size of a VirtualBox Win7 .vdi disk on Ubuntu 10.04 but when I try executing VBoxManage modifyhd /path/disk.vdi --resize 15360 it returns Syntax error: unknown option: --resize. I'm unsure as to why this is happening because I've used it before and it's still listed under valid options for VBoxManage modifyhd in the VirualBox User Manual . Cheers, George @maniat1k george@george-laptop:~$ VBoxManage modifyhd '/home/george/.VirtualBox/HardDisks/Windows 7 64bit.vdi' --resize 15360 Sun VirtualBox Command Line Management Interface Version 3.1.6_OSE (C) 2005-2010 Sun Microsystems, Inc. All rights reserved. Usage: VBoxManage modifyhd | [--type normal|writethrough|immutable] [--autoreset on|off] [--compact] Syntax error: unknown option: --resize

  Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >