Search Results

Search found 20049 results on 802 pages for 'virtual drive'.

Page 69/802 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

  • Virtual Machine Network Architecture, Isolating Public and Private Networks

    - by Mark
    I'm looking for some insight into best practices for network traffic isolation within a virtual environment, specifically under VMWARE ESXi. Currently I have (in testing) 1 hardware server running ESXi but i expect to expand this to multiple pieces of hardware. The current setup is as follows: 1 pfsense VM, this VM accepts all outside (WAN/internet) traffic and performs firewall/port forwarding/NAT functionality. I have multiple public IP addresses sent to the this VM that are used for access to individual servers (via per incoming IP port forwarding rules). This VM is attached to the private (virtual) network that all other VMs are on. It also manages a VPN link into the private network with some access restrictions. This isn't the perimeter firewall but rather the firewall for this virtual pool only. I have 3 VMs that communicate with each other, as well as have some public access requirements: 1 LAMP server running an eCommerce site, public internet accessible 1 accounting server, access via windows server 2008 RDS services for remote access by users 1 inventory/warehouse management server, VPN to client terminals in warehouses These servers constantly talk with each other for data synchronization. Currently all the servers are on the same subnet/virtual network and connected to the internet through the pfsense VM. The pfsense firewall uses port forwarding and NAT to allow outside access to the servers for services and for server access to the internet. My main question is this: Is there a security benefit to adding a second virtual network adapter to each server and controlling traffic such that all server to server communication is on one separate virtual network, while any access to the outside world is routed through the other network adapter, through the firewall, and on the the internet. This is the type of architecture i would use if these were all physical servers, but i'm unsure if the networks being virtual changes the way i should approach locking down this system. Thank you for any thoughts or direction to any appropriate literature.

    Read the article

  • Flaws in my PHP development setup - sharing sources causing lags

    - by Wiktor
    I have following development setup for my PHP projects: Working station running on Windows 7 with PhpStorm IDE. GIT for version controlling. CentOS on virtual machine (VirtualBox) with Apache and MySQL (copy of production server). So far, I've been sharing project's source folders between host and guest systems and it was working quite well only really slow. The reason behind this is that Apache was reading files from remote folder (mounted locally). After doing some research, I found out that this set up can be improved by using disk mapping (Samba) instead of folder sharing. So I did that change. I configured my PhpStorm to automatically deploy files to mapped drive. Everything works like a charm now, except for one problem - when I change branches I need to synchronize project's local folder with the one on mapped drive and that takes time, a lot of time (like branching in SVN). Is there another way to handle this than just working on files directly on mapped drive?

    Read the article

  • Free software for backing up an attached network drive

    - by Richard
    My wireless router comes with a USB connector which allows me to plug an external hard drive in and it'll act as a Network Attached Storage. The problem is that I want to backup this hard-drive to the external drive of another computer so that if the NAS drive fails, I don't lose everything. However, Windows 7 Backup refuses to include the NAS as a location to backup. I can't fool it by mapping it to a drive letter either. Google presents lots of pages on how to backup files to a NAS, but not the other way around. Can anyone advise me on free software which can do incremental backups of a NAS drive to an external drive attached the computer it is running on? I'm aware of this question but the top answers have one or more of the following issues: They aren't free. The free version cannot backup a NAS. They cannot do incremental backups. They're just a script and therefore have limited other functionality (eg. disk space management, scheduling, compression, etc.etc.)

    Read the article

  • External SATA drive does not work without the optional USB cable *also* connected

    - by Software Monkey
    I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

    Read the article

  • Windows Server 2008 R2 Virtual Network Setup

    - by jpearl01
    Hi all, Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

    Read the article

  • Transferring an SQL Processor License to a virtual hosted environment

    - by Andrew Shepherd
    My company is currently hosting a service in-house, and we want to move to an externally hosted environment. We would then be using a virtual server. I understand that this might be spread across multiple machines, but from my perspective as a customer, this layer is abstracted away - I shouldn't know or care about the hardware that the OS is hosted on. We have a licensed edition of SQL Server 2008. This is one Processor license. Will it be a violation of the licensing agreement to use this in a virtual environment. From the reference guide here it says When licensed Per Processor With Workgroup, Web, and Standard editions, for each server to which you have assigned the required number of per processor licenses, you may run, at any one time, any number of instances of the server software in physical and virtual operating system environments on the licensed server. However, the total number of physical and virtual processors used by those operating system environments cannot exceed the number of software licenses assigned to that server For enterprise edition there is an added option: if all physical processors in a machine have been licensed, then you may run unlimited instances of SQL server 2008 in one physical and an unlimited number of virtual operating environments on that same machine. I'm having trouble getting my head around this. Would I theoretically have to get a license for every processor in this virtual environment (which is effectively impossible because I have no way of knowing how many processors there actually are)? Or can I just say that it's hosted on one "virtual" server, so that's OK?

    Read the article

  • Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

    - by Kento Locatelli
    I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

    Read the article

  • Windows Server 2008 R2 Virtual Network Setup

    - by jpearl01
    Some background: I'm very much new to networking in general, and virtualization in particular. I'm trying to set up a series of VMs as we are transitioning to a thin client setup. I have been supplied a limited number of static ip addresses. The server is located in an offsite building which houses the network we use to connect to the internet, share folders etc. The setup I've been trying to go for is this: The host OS (Windows Server 2008 R2) is bound to one nic using one of the static ips (say, Nic1 and ip 10.255.6.61). I've set up another external virtual network attached to another physical nic , and a virtual private network attached to no nic. There is one VM running the same os (as the host). This VM is connected to both the external virtual network (and uses another static ip say Nic2 and ip 10.255.6.62) and also to the virtual private network (I gave it a static random ip 192.168.88.1 subnet mask 255.255.255.0). This virtual private network is connected to all the other VMs. I'd like to share the internet connection with all the other VMs on the private virtual network, and so I installed the RRAS role on the server connected to Nic2, and selected the option to share the internet over the vpn. I've run through the RRAS wizard a few times, trying different configurations, but none of them seem to be letting the other vms connect to the 'net. The vms seem to connect to the virtual private network fine, they are assigned an ip address and everything, but no internet, and no rest of the network either. The other problem is in general I connect to the vms with RDP. Will that be possible with a setup like this? i.e. will the vms show up as computers on the network? If not, what are my other options? Thanks! ~josh

    Read the article

  • USB drive was bootable, but no longer boots

    - by i-g
    I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? I think it lost some pixie dust when I formatted it with the standard Windows formatting tool (it was quicker than deleting files), but I have no idea what it was or how to get it back. The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

    Read the article

  • USB drive was bootable, but no longer isn't

    - by i-g
    I'm trying to install a new OS onto a computer from a bootable USB stick. I previously installed Ubuntu Linux and it was a piece of cake -- I downloaded the ISO image, used UNetbootin to copy it to the USB drive and make it bootable, and that was that. Now, however, no matter what I try, I can't make the same USB drive bootable again! I've tried formatting it as FAT32 and NTFS. I've tried several different Linux distributions and Windows 7. I've tried using UNetbootin, Windows 7 USB Download Tool, WinToFlash, and manually making it bootable with diskpart/bootsect/bootrec. (Yes, I've tried bootsect /nt60 x: /force.) None of this seems to be working! When I try to boot from the drive, the machine reads from it (I can see the drive's LED blinking) and then gives me the same "Insert system disk and press Enter" message. (I've disabled booting from the hard drive.) Am I missing something I need to do to make the USB drive bootable again? The USB drive in question is a SanDisk Cruzer 8GB SDCZ6. The computer I'm working on is running Windows Vista SP1.

    Read the article

  • INACCESSIBLE_BOOT_DEVICE after installing Linux on same drive

    - by kdgregory
    History: My PC was configured with two drives: an 80G on IDE 0 Primary that was running Win2K, and a 320G on IDE 0 Secondary that was running Linux (Ubuntu). I decided to pull the 80Gb drive out of the system, so dd'd the entire 80 G drive (/dev/sda) onto the 320 (/dev/sdb) -- this included the MBR and partition table. Then I pulled the drive, plugged the 320 into IDE 0 Primary, and rebooted. The Windows partition worked at this point. Then I installed Ubuntu into the remaining space on the 320. It works. However, when I try to boot into Windows, I get a BSOD with the following message: *** STOP: 0x0000007B (0x89055030,0xC000014F,0x00000000,0x00000000) INACCESSILE_BOOT_DEVICE Before the BSOD I see the Win2K splash screen, and it claims to be "starting windows" for a couple of seconds -- so it appears that the first stage boot loader is working as expected. Ditto when I try booting in Safe Mode. After reading the Microsoft KB article, I booted into the recovery console and tried running chkdsk /r. It refused to run, claiming that the drive was corrupted (sorry, didn't write down the exact error message). However, I can mount the drive from Linux, and access all files. And for what it's worth, I can scan the drive using the Linux "Disk Utility" (this is Ubuntu, the menus don't show real program names), it claims the drive to be clean. The KB article mentioned that boot.ini could be the problem, so here it is: timeout=10 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows 2000 Professional" /fastdetect Any pointers on what to do next?

    Read the article

  • Why doesn't the installer see all of my hard drives?

    - by atodd
    I'm trying to setup a dual boot system with Windows Vista 64 (already installed) and Ubuntu 10.10. I added a new drive which is identical to the one Vista is installed on. When I boot into the LiveCD I can see and mount the second drive and edit it in Gparted. However, when I use the installer it will only bring up the drive that already has Vista installed. I've tried everything I know. I'm not sure if its a BIOS setting or something else I've missed. I've also tried both the desktop and alternate amd64 installs with the same result.

    Read the article

  • Fixing Windows install by connecting its hard drive via USB to a different laptop

    - by Jason
    I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

    Read the article

  • Fixing Windows install by connecting it's hard drive via USB to a different laptop

    - by Jason
    I tried to upgrade a laptop to SP3, which broke it. I later found out SP3 doesn't work on that 2002 laptop. I can't uninstall SP3, or fix SP2, because the hard drive is now not detected during setup (I've read that's the problem you get). I put the hard drive in a USB drive case and plugged it into my other laptop, and I can read (& write to) the disk okay. (The hard drive won't fit in my other laptop, so I'm using USB.) I need to get that disk back to SP2, or fix whatever files got screwed up causing the disk to not be recognized. I don't want to do a re-install as there are 80GB of files on it I need, and they won't fit on the HD of my other laptop, and also because I no longer have some of the install CDs for software on it. What do I need to do to fix that drive from my other laptop? (I don't want my working laptop (XP SP3) to get screwed with by putting an SP2 disk in the CD drive, or the non-o/s data on the other hard drive screwed with.)

    Read the article

  • How do I restore GRUB 2?

    - by uahug
    I upgraded my laptop with an SSD, moving my old HDD to where the DVD-drive was, so that I could have speed and storage. Now, I have reinstalled Ubuntu on the SSD, deleting all the partitions on the old HDD to make space for a data partition. But now the laptop doesn't even get to GRUB 2 if the HDD is plugged in! If I take it out, everything works, but as soon as I plug it in and retry to boot, I won't find GRUB. At first, I thought it was because of the boot order, but the order was OK: first the notebook hard drive (SSD) and then the CD/DVD drive (which in reality is the HDD). How can I fix it? Doing a simple grub-install /dev/sda doesn't work.. The SSD is sda, and the HDD is sdb.

    Read the article

  • Why doesn't the Ubuntu Installer see all of my hard drives

    - by atodd
    I'm trying to setup a dual boot system with Windows Vista 64 (already installed) and Ubuntu 10.10. I added a new drive which is identical to the one Vista is installed on. When I boot into the LiveCD I can see and mount the second drive and edit it in Gparted. However, when I use the installer it will only bring up the drive that already has Vista installed. I've tried everything I know. I'm not sure if its a BIOS setting or something else I've missed. I've also tried both the desktop and alternate amd64 installs with the same result.

    Read the article

  • How do you find a functions virtual call address in assembly?

    - by Daniel
    I've googled around but i'm not sure i am asking the right question or not and i couldn't find much regardless, perhaps a link would be helpful. I made a c++ program that shows a message box, then I opened it up with Ollydbg and went to the part where it calls MessageBoxW. The call address of MessageBoxW changes each time i run the app as windows is updating my Imports table to have the correct address of MessageBoxW. So my question is how do i find the virtual addres of MessageBoxW to my imports table and also how can i use this in ollydbg? Basically I'm trying to make a code cave in assembly to call MessageBoxW again. I got fairly close once by searching the executable with a hex editor and found the position of the call, and I think I found the virtual address. But when i call that virtual address in olly and saved it to the executable, the next time i opened it the call was replaced with a bunch of DB xyz (which looked like the virtual address but why did the call get removed? Sorry if my terminology is off as i'm new to this so i'm not quite sure what to call things.

    Read the article

  • Is there a performance difference between Windows 7 on SSD installed from scratch versus it using a recent ghost/clone drive image from a harddisk?

    - by therobyouknow
    I'm planning to upgrade a notebook PC to a Solid-State Flash Drive (SSD) soon. I want to use the notebook before that and am considering installing Windows 7 on the hard disk (spinning variety, 5400rpm) before I get the SSD. To save time I am wondering if I can ghost/clone the installation of Windows 7 from the hard drive and put on the SSD. Would the performance of this clone from the harddisk onto the SSD be different from starting again and reinstalling Windows 7 from scratch on the SSD? (Windows 7 32bit professional)

    Read the article

  • What are the advantages and disadvantages of the various virtual machine image formats?

    - by Matt
    Xen and Virtualbox etc both support a range of different virtual machine image formats. These are: vmdk, vdi, qcow & qcow2, hdd & vhd. Without any bias toward a particular product, I'm wanting to know what are the advantages and disadvantages of the various formats both from a features perspective, robustness and speed? One piece of info I discovered in a forum post was this: "The major difference is that VDI uses relatively large blocks (1MB) when growing an image, and thus has less overhead for block pointers etc. but isn't ultimately space efficient in the sense that if a single byte is non-zero in such a 1MB block the entire space is used. VMDK in contrast uses 64K blocks, and thus has more management overhead and generally a bit less disk space consumption What offsets this is that VDI is more efficient when it comes to snapshots." You might be thinking, I want to know this because I want to know which format to choose? Not exactly, I'm developing some software which utilises these formats and want to support one or more of them. Simplicity, large disks and ease of development are my main drivers.

    Read the article

  • What are "Excess Fragments" in defragmenting a hard drive?

    - by Andrew Swift
    I'm defragmenting my hard drive (XP SP3) with PerfectDisk 7.0, and it finds 816,659 excess fragments when I ask for an analysis. [update] Specifically, it shows that the 1TB disk is 14% fragmented with 19693 fragments and 816,659 excess fragments. About 20% of the disk is still free space. What does excess fragments refer to? What is the difference between fragments and excess fragments? I have had problems in the past where I defragmented a fragmented disk and many files were corrupted. It seemed as though "excess fragments" referred to orphan pieces, where the program couldn't find out where to put them. If that was true, then defragmenting a disk resulted in many incomplete files, and in fact I defragmented a disk full of MP3's and got a lot of corrupted files as a result. Instead, I started to simply format a separate disk and copy everything from one to the other. That way there were no orphan bits, and no file corruption. Does anybody know what "excess fragments" really are?

    Read the article

  • If I partition a drive connected via eSata will it show different partitions when connected via USB?

    - by jeffreypriebe
    I have an odd problem with an external drive. I'm formatting it connected to my laptop prior to connecting it to my router. The HDD enclosure has both an eSata and USB connections. Generally, I connect it via eSata to my laptop. I created my partitions and connected it to the router, but I see partition information that is different than what I created. After chasing leads concerning large HDD size, I mindlessly connected the HDD to my laptop with USB. Lo! I see the same partitions as the router. Attached are screenshots using the same program and the HDD in question. The only difference is the connection. For the first, I connected via eSata and hit "refresh" on the partition program. Then, turned off the HDD, disconnected the eSata cable, and connected via USB. Power and refresh. eSata: reports a total HDD size of 2328 GB, with four partitions (the third being 1.96TB) USB: reports a total HDD size of 280 GB, with three partitions (the third being 279 GB) Any idea why this is happening? It looks like it clearly is an issue of the 4K sector size and not playing nice with the USB enclosure. I tried it eSata and USB in Windows and Linux and it appears consistently that eSata is reporting correctly, USB incorrectly.

    Read the article

  • Are there any disadvantages of having a "free fall sensor" on a hard disk drive?

    - by therobyouknow
    This is a general question that came out of a specific comparison between the Western Digital Scorpio WD3200BEKT and Western Digital Scorpio WD3200BJKT (which is the same as the former but with a free fall sensor.) Note: I'm not asking for a review or appraisal of these specific drives, as the general question does apply on other brands as well. Though your input would help my decision. To break down the general question in order to answer it, I would be looking for comments on things like: if it's necessary to have differing physical dimensions between free fall sensor drives and those without, e.g. does it make it any thicker, and therefore reduce the systems where it can be installed - particularly smaller laptops? does it actually make the system less reliable - because of false alarms whereby the drive thought the laptop was falling but it wasn't? I suppose that the fact that a manufacturer produces both drives with and without free fall sensors says something about possible disadvantages. Or it could be standard marketing techniques where by making drives with and without results in larger sales volume than just those with the feature alone.

    Read the article

  • CD/DVD Drive not detecting locally burned CD/DVDs, but works fine with Genuine discs.

    - by Rahul
    I'm using Dell Inspiron 1420 - 32 Bit - Windows Vista, since 2.5 years. I'm facing a strange problem with my CD/DVD-drive. I cannot run/play a CD/DVD which I get burned from my friends. But when I insert Genuine CD, I'm able to play/run it. And when I try to install my Vista package which I got with my notebook, the CD/DVD gets loaded. If I insert a CD/DVD which I get from my friend, CD doesn't get loaded and the system gets hanged. But all these CDs/DVDs work on other systems. I've tested it on many of my friends PCs. So, now I'm able to run only genuine CDs & a few genuine DVDs. My Experience/Experiments: I tried to install Windows Vista using Genuine DVD - It worked I tried to install Ubuntu which I got from shipped from Canonical Ltd. - It worked I tried to install OpenSUSE .iso file burned to a DVD in my friend's PC - It didn't work for me (But working perfectly fine in my friends PCs(Tested in 4 other PCs) Tried to play a DVD containing movies, burned in my friend's PC - It didn't work for me (But working perfectly fine in my friends PCs Any help/suggestions would be appreciated. Thanks.

    Read the article

  • Does migrating 2 domain controllers between 2 datacentre requires both virtual machines to be shut down at the same time?

    - by Imagineer
    I was attempting to migrate 2 virtual machines that are domain controllers between 2 datacentres running ESX 3.5 and ESX 4.1. I was advised to shut down both domain controller at the same time during the migration process. This is to avoid USN Rollback and other replication issues. The following are the steps that I was planning to perform: 1. Shutdown both DC. 2. Copy both VMs files across to new datacentre using Veeam FastSCP (connection to both vCentre through IP address instead of hostname) 3. Power them up at new datacentre. 4. Configure Network interface/DNS/DHCP for both DCs in new datacentre I have tried to use Veeam FastSCP rather than VMware Standalone Converter is because its copying rather than converting. Someone also suggested that I use backup and restore app like Veeam backup and replication software. Sounds like a simple job, but after shutting down both DCs, the transfer rate using FastSCP is so slow registering only 1KB/s as oppose to the normal 1MB/s (or more). When that attempt to transfer failed, I tried to cold clone both DCs resulted in the both ESX hosts get disconnected. I have tried troubleshooting by referring to this - VMware KB - Diagnosing an ESX Server that is Disconnected or Not Responding in VirtualCenter It seems that the DNS being down is the caused of all unusual occurrence. The moment I powered up the DCs via VMware console command, the ESX host were able to connect to the vCentre again. How can I avoid such a pitfall again? Am I doing it correctly? Any help would be greatly appreciated! Thank you.

    Read the article

  • Azure Virtual Machines - what fault tolerance do they provide?

    - by Borek
    We are thinking about moving our virtual machines (Hyper-V VHDs) to Windows Azure but I haven't found much about what kind of fault tolerance that infrastructure provides. When I run VHD in Azure, I've got two questions: Is my VHD and all the data in it safe? I think that uploaded VHDs use the "Storage" infrastructure so they should be automatically replicated to multiple disks and geographically distributed but should I still make a full-image backup just to be safe? (Note that of course I will be backing up the actual data inside VMs that I care about; I just want to know if there is a chance greater than 0.0000001% that one day I will receive an email from Microsoft telling me that my VM is gone and that I should create or restore it from scratch). Do I need to worry about other things regarding the availability of my VMs? I mean, when I have an on-premise server I need to worry about the hardware itself, about the host operating system, what would happen if my router failed, if my Hyper-V's C: drive failed etc. Am I right in thinking that with Azure, their infrastructure takes care of all of this? Thanks.

    Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >