Search Results

Search found 19539 results on 782 pages for 'pretty print'.

Page 697/782 | < Previous Page | 693 694 695 696 697 698 699 700 701 702 703 704  | Next Page >

• VPN IP Routing - slow connections

  - by dannymcc

  UPDATE: Router error logs show: LCP Time-out 0 I'm not sure how to correct this. The Lan-to-Lan profiles are set to -1 Idle Timeout (for the remote branch). I have a PPTP VPN running between two Draytek 2820 routers. They are setup that one dials out to the other one. Main Practice - 192.168.1.0/24 Branch - 192.168.3.0/24 I have then set (on the Branch) router the following route: 192.168.1.0/24 If I then request a server running on 192.168.1.1 from the Branch, it correctly routes through VPN tunnel. If I request the branch server at 192.168.3.1 it correctly routes to the local server without using the VPN tunnel. I have temporarily disabled the firewall on both routers, and made sure that QoS is disabled. The Main Practice internet connection is ~30mb down / ~10mb up, and the Branch connection is ~5mb down / ~2mb up. Anything over the VPN tunnel runs pretty slowly (VNC, Remote Desktop and Terminal Emulators). However, if I dial using the Windows VPN wizard, creating a connection from the laptop to the Main Practice - everything runs quickly. I'm looking for possible causes, and/or ways of further diagnosing the issue. Any help would be greatly appreciated! UPDATE: In summary, when I connect within the Branch and try and access a host that's within the Main Practice it works, but slowly. If I then dial the VPN on my Windows 7 laptop whilst still connected to the Branch network, it's fast. Main Practice Branch Practice Routing Table from Branch Router Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 126.256.126.103 WAN2 C~ 192.168.1.99/ 255.255.255.255 directly connected VPN-1 S~ 192.168.1.0/ 255.255.255.0 via 192.168.1.99 VPN-1 S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.99 VPN-1 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2 C 126.256.126.103/ 255.255.255.224 directly connected WAN2 Routing Table from Main Practice Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 81.139.64.1, WAN2 S 81.137.176.1/ 255.255.255.255 via 81.137.176.1, WAN2 * 81.139.64.1/ 255.255.255.255 via 81.139.64.1, WAN2 C~ 192.168.1.204/ 255.255.255.255 is directly connected, VPN C~ 192.168.1.0/ 255.255.255.0 is directly connected, LAN S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.204, VPN S~ 192.168.3.0/ 255.255.255.0 via 192.168.1.203, VPN Connection Details (from Branch Router) Connection Details (from Main Practice Router) IPERF.exe Output

  Read the article

• network is not available even when cisco vpn client is connected. wrong route?

  - by javapowered

  I'm using Vodafone 3G modem. I've disabled other network devices in the system (ethernet, wifi, wimax) turned off firewall and antivirus. cisco vpn client connects successfully but I still can not access computer 192.168.147.120 (as well as any other computer from network). Any suggestions are welcome as I don't know what to do. ipconfig /all and route print commands (translated to english): Microsoft Windows [Version 6.1.7601] (C) Microsoft Corporation (Microsoft Corp.), 2009. All rights reserved. C: \ Users \ Oleg> ipconfig / all IP Configuration for Windows The name of the computer. . . . . . . . . : OlegPC The primary DNS-suffix. . . . . . : Node Type. . . . . . . . . . . . . : Hybrid IP-routing is enabled. . . . : No WINS-proxy enabled. . . . . . . : No Ethernet adapter Local Area Connection 4: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Cisco Systems VPN Adapter Physical Address. . . . . . . . . 00-05-9A-3C-78-00 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Local IPv6-address channel. . . : Fe80:: c073: 41b2: 852f: eb87% 26 (Preferred) IPv4-address. . . . . . . . . . . . : 10.53.127.204 (Preferred) The subnet mask. . . . . . . . . . : 255.0.0.0 Default Gateway. . . . . . . . . : IAID DHCPv6. . . . . . . . . . . : 536872346 DUID the client DHCPv6. . . . . . . 00-01-00-01-14-6F-4C-8D-60-EB-69-85-10-2D DNS-servers. . . . . . . . . . . : Fec0: 0:0: ffff:: 1% 1 fec0: 0:0: ffff:: 2% 1 fec0: 0:0: ffff:: 3% 1 NetBios over TCP / IP. . . . . . . . : Disabled Adapter mobile broadband connection through a broadband adapter mobile communications: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Vodafone Mobile Broadband Network Adapter (Huawei) Physical Address. . . . . . . . . 58-2C-80-13-92-63 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv4-address. . . . . . . . . . . . : 10.229.227.77 (Preferred) The subnet mask. . . . . . . . . . : 255.255.255.252 Default Gateway. . . . . . . . . : 10.229.227.78 DNS-servers. . . . . . . . . . . : 163.121.128.134 212.103.160.18 NetBios over TCP / IP. . . . . . . . : Disabled Tunnel adapter isatap. {737FF02E-D473-4F91-840E-2A4DD293FC12}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 3 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter isatap. {EF585226-5B07-4446-A5A4-CB1B8E4B13AC}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 4 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv6-address. . . . . . . . . . . . : 2001:0:4137:9 e76: ea: b77: f51a: 1cb2 (Basically d) Local IPv6-address channel. . . : Fe80:: ea: b77: f51a: 1cb2% 16 (Preferred) Default Gateway. . . . . . . . . ::: NetBios over TCP / IP. . . . . . . . : Disabled C: \ Users \ Oleg> route print ================================================== ========================= List of interfaces 26 ... 00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter 23 ... 58 2c 80 13 92 63 ...... Vodafone Mobile Broadband Network Adapter (Huawei) 1 ........................... Software Loopback Interface 1 19 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 3 20 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 4 16 ... 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface ================================================== ========================= IPv4 Route Table ================================================== ========================= Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.229.227.78 10.229.227.77 296 10.0.0.0 255.0.0.0 On-link 10.53.127.204 286 10.6.93.21 255,255,255,255 10.0.0.1 10.53.127.204 100 10.13.50.12 255,255,255,255 10.0.0.1 10.53.127.204 100 10.53.8.0 255.255.252.0 10.0.0.1 10.53.127.204 100 10.53.127.204 255.255.255.255 On-link 10.53.127.204 286 10.53.128.0 255.255.248.0 10.0.0.1 10.53.127.204 100 10.53.148.0 255,255,255,240 10.0.0.1 10.53.127.204 100 10.53.148.16 255,255,255,240 10.0.0.1 10.53.127.204 100 10.229.227.76 255.255.255.252 On-link 10.229.227.77 296 10.229.227.77 255.255.255.255 On-link 10.229.227.77 296 10.229.227.79 255.255.255.255 On-link 10.229.227.77 296 10.255.255.255 255.255.255.255 On-link 10.53.127.204 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.147.0 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.147.96 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,112 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,128 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,144 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,224 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.214.0 255.255.255.0 10.0.0.1 10.53.127.204 100 192.168.215.0 255.255.255.0 10.0.0.1 10.53.127.204 100 194.247.133.19 255,255,255,255 10.0.0.1 10.53.127.204 100 213,247,231,194 255,255,255,255 10.229.227.78 10.229.227.77 100 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.229.227.77 296 224.0.0.0 240.0.0.0 On-link 10.53.127.204 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.229.227.77 296 255.255.255.255 255.255.255.255 On-link 10.53.127.204 286 ================================================== ========================= Persistent Routes: None IPv6 Route Table ================================================== ========================= Active Routes: If Metric Network Destination Gateway 16 58:: / 0 On-link 1306:: 1 / 128 On-link 16 58 2001:: / 32 On-link 16 306 2001: 0:4137:9 e76: ea: b77: f51a: 1cb2/128 On-link 16 306 fe80:: / 64 On-link 26 286 fe80:: / 64 On-link 16 306 fe80:: ea: b77: f51a: 1cb2/128 On-link 26 286 fe80:: c073: 41b2: 852f: eb87/128 On-link 1306 ff00:: / 8 On-link 16 306 ff00:: / 8 On-link 26 286 ff00:: / 8 On-link ================================================== ========================= Persistent Routes: None C: \ Users \ Oleg>

  Read the article

• Disk performance below expectations

  - by paulH

  this is a follow-up to a previous question that I asked (Two servers with inconsistent disk speed). I have a PowerEdge R510 server with a PERC H700 integrated RAID controller (call this Server B) that was built using eight disks with 3Gb/s bandwidth that I was comparing with an almost identical server (call this Server A) that was built using four disks with 6Gb/s bandwidth. Server A had much better I/O rates than Server B. Once I discovered the difference with the disks, I had Server A rebuilt with faster 6Gbps disks. Unfortunately this resulted in no increase in the performance of the disks. Expecting that there must be some other configuration difference between the servers, we took the 6Gbps disks out of Server A and put them in Server B. This also resulted in no increase in the performance of the disks. We now have two identical servers built, with the exception that one is built with six 6Gbps disks and the other with eight 3Gbps disks, and the I/O rates of the disks is pretty much identical. This suggests that there is some bottleneck other than the disks, but I cannot understand how Server B originally had better I/O that has subsequently been 'lost'. Comparative I/O information below, as measured by SQLIO. The same parameters were used for each test. It's not the actual numbers that are significant but rather the variations between systems. In each case D: is a 2 disk RAID 1 volume, and E: is a 4 disk RAID 10 volume (apart from the original Server A, where E: was a 2 disk RAID 0 volume). Server A (original setup with 6Gpbs disks) D: Read (MB/s) 63 MB/s D: Write (MB/s) 170 MB/s E: Read (MB/s) 68 MB/s E: Write (MB/s) 320 MB/s Server B (original setup with 3Gpbs disks) D: Read (MB/s) 52 MB/s D: Write (MB/s) 88 MB/s E: Read (MB/s) 112 MB/s E: Write (MB/s) 130 MB/s Server A (new setup with 3Gpbs disks) D: Read (MB/s) 55 MB/s D: Write (MB/s) 85 MB/s E: Read (MB/s) 67 MB/s E: Write (MB/s) 180 MB/s Server B (new setup with 6Gpbs disks) D: Read (MB/s) 61 MB/s D: Write (MB/s) 95 MB/s E: Read (MB/s) 69 MB/s E: Write (MB/s) 180 MB/s Can anybody suggest any ideas what is going on here? The drives in use are as follows: Dell Seagate F617N ST3300657SS 300GB 15K RPM SAS Dell Hitachi HUS156030VLS600 300GB 3.5 inch 15000rpm 6GB SAS Hitachi Hus153030vls300 300GB Server SAS Dell ST3146855SS Seagate 3.5 inch 146GB 15K SAS

  Read the article

• VMWare Network bug in multiple VMWare Workstation versions if using a hardcoded IP address

  - by onyxruby

  I'm having a very tricky problem with some of my VM sessions being unable to reach the Internet or even ping the gateway. I have just set up a new VM Workstation (7) on a W2K8 64bit server (I'll be converting to ESXI 4 once I can find a decent book on it, so for the meanwhile I use workstation). I have imported a number of VM's and setup some new ones on the server.In short the problem with some of the VM's being unable to reach the Internet is that they can't reach the gateway. I've looking at a number of things and can pretty safely rule out the following: Switch, Router, DHCP Server, DNS, Client IP configuration, Routes and typos. The problem is that some of the new clients cannot reach the gateway if their IP address is hardcoded, they can't even ping it by IP address. That rules out DNS and DHCP. Now, if I allow them to get their IP address by DHCP they can reach the gateway and Internet without issue. The interesting thing on this, is that this behavior occurs even if I leave the DNS information hardcoded under TCP/IP settings. It doesn't work unless the IP and gateway are handed out by DHCP even though the same information IP info is being used by the host. Fundamentally from the standpoint of the clients, they are trying to reach the exact same gateway using the exact same IP information regardless of whether they are hardcoded or assigned by DHCP. Here's an example of one client. IP Address 192.168.7.66 - Subnet Mask 255.255.255.0 - Gateway 192.168.7.254 - DNS1 192.168.7.44 - DNS2 192.168.7.254. The issue occurs across six different microsoft operating systems, Windows 7 and Windows 2008 variants all have the issue. My W2K3, XP, Vista and W98 clients all work without issue with hardcoded IP addresses. I have tried things like rearranging the DNS order, flushing DNS and so on. It's not a routing or switch issue as the clients can work just fine if they get their IP by DHCP. It's not a paramater issue as the exact same paramaters are handed out by DHCP as I plug in by hand. It's not a DNS issue as clients cant reach other clients even with IP addresses only. I have run a tracert to the gateway by IP address and it times out on the very first hop before failing on hop3 with destination host unreachable. If I get the IP address by DHCP the tracert finds the gateway (and Internet) without issue. I have read a few other posts online in forums talking about this problem randomly occuring over the years in other VM versions as well, so I suspect some kind of long standing bug. Does anyone have any ideas on this? Is it possibly a bug with Windows 7 and W2K clients under VM?

  Read the article

• Indesign Import XML into Automatic Page generation, data merge

  - by taudep

  I've created some InDesign Pages that I want to use as templates. I've created an XML file with all the appropriate data. I want to merge the XML data with the InDesign page and have a few hundred pages automatically generated. I've been reading online and working with InDesign's "Import XML" features without any luck. The documentation has been pretty poor for me. And Google searches haven't returned much fruitful. Here are my present steps: I create a Master Page of my template I add a bunch of text frames where I want the imported data from the XML file to be places I open the "Tags" window and Import and XML file I mark my text frames in the Master Document with the appropriate tags I then add a lot of pages (like 200) to the document Then I use "Import XML" to try and get the data brought in and filled across all 200 pages. This is where I fail. There's something I'm missing. It might be that InDesign doesn't work as I'm expecting... Does anyone have any good tips for mail-merge like functionality with an XML document and auto-generation of InDesign pages? By the way, here's an example of Adobe's great documentation for merging repeated XML elements. There's got to be more... InDesign CS4 Docs: XML-Importing XML-Working with Repeating Data Here's some of the sample XML, notice the ITEM will repeat. I've also truncated the data in the "desc" tag: <output> <item> <user_name>taude</user_name> <date>2009-02-21</date> <title>Wishful Thinking</title> <desc>Skiing up in Vermont on a beautiful day. This photo of</desc> <thumbnail>http://www.blipfoto.com/thumbs/5371/2009/big/color/96104200949a162672e1996.15963073.jpeg</thumbnail> </item> <item> <user_name>taude</user_name> <date>2009-02-22</date> <title>Skiing Self Portrait</title> <desc>I was inspired by ML's self-portrait while </desc> <thumbnail>http://www.blipfoto.com/thumbs/5371/2009/big/color/36547696749a2c5782308e0.91477014.jpeg</thumbnail> </item> </output> Here's what my imported XML looks like with the InDesign Structure:

  Read the article

• cPanel Virtfs won't umount

  - by JPerkSter

  Anyone have any experience with virtfs on cPanel servers? I can't seem to get them to unmount, as they say they are already unmounted: [root@Server ~]# cat /proc/mounts | grep user /dev/root /home/virtfs/user/lib ext3 rw,errors=continue,data=ordered 0 0 /dev/root /home/virtfs/user/opt ext3 rw,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/lib ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/sbin ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/share ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/bin ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/man ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/X11R6 ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/kerberos ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/libexec ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/local/bin ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/local/share ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/local/Zend ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/local/IonCube ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/include ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda3 /home/virtfs/user/usr/local/lib ext3 rw,nodev,errors=continue,data=ordered 0 0 /dev/sda2 /home/virtfs/user/var/spool ext3 rw,nodev,noatime,nodiratime,errors=continue,data=ordered 0 0 /dev/sda2 /home/virtfs/user/var/lib ext3 rw,nodev,noatime,nodiratime,errors=continue,data=ordered 0 0 /dev/sda2 /home/virtfs/user/var/cpanel ext3 rw,nodev,noatime,nodiratime,errors=continue,data=ordered 0 0 /dev/sda2 /home/virtfs/user/var/run ext3 rw,nodev,noatime,nodiratime,errors=continue,data=ordered 0 0 /dev/sda2 /home/virtfs/user/var/log ext3 rw,nodev,noatime,nodiratime,errors=continue,data=ordered 0 0 /dev/sda6 /home/virtfs/user/tmp ext3 rw,nosuid,nodev,noexec,noatime,errors=continue,data=ordered 0 0 /dev/root /home/virtfs/user/bin ext3 rw,errors=continue,data=ordered 0 0 [root@Server ~]# for i in cat /proc/mounts |grep virtfs |grep user |awk '{print$2}'; do umount $i; done umount: /home/virtfs/user/lib: not mounted umount: /home/virtfs/user/opt: not mounted umount: /home/virtfs/user/usr/lib: not mounted umount: /home/virtfs/user/usr/sbin: not mounted umount: /home/virtfs/user/usr/share: not mounted umount: /home/virtfs/user/usr/bin: not mounted umount: /home/virtfs/user/usr/man: not mounted umount: /home/virtfs/user/usr/X11R6: not mounted umount: /home/virtfs/user/usr/kerberos: not mounted umount: /home/virtfs/user/usr/libexec: not mounted umount: /home/virtfs/user/usr/local/bin: not mounted umount: /home/virtfs/user/usr/local/share: not mounted umount: /home/virtfs/user/usr/local/Zend: not mounted umount: /home/virtfs/user/usr/local/IonCube: not mounted umount: /home/virtfs/user/usr/include: not mounted umount: /home/virtfs/user/usr/local/lib: not mounted umount: /home/virtfs/user/var/spool: not mounted umount: /home/virtfs/user/var/lib: not mounted umount: /home/virtfs/user/var/cpanel: not mounted umount: /home/virtfs/user/var/run: not mounted umount: /home/virtfs/user/var/log: not mounted umount: /home/virtfs/user/tmp: not mounted umount: /home/virtfs/user/bin: not mounted umount: /home/virtfs/user/dev: not mounted umount: /home/virtfs/user/proc: not mounted

  Read the article

• UNIX - mount: only root can do that

  - by Travesty3

  I need to allow a non-root user to mount/unmount a device. I am a total noob when it comes to UNIX, so please dumb it down for me. I've been looking all over teh interwebz to find an answer and it seems everyone is giving the same one, which is to modify /etc/fstab to include that device with the 'user' option (or 'users', tried both). Cool, well I did that and it still says "mount: only root can do that". Here are the contents of my fstab: # /etc/fstab: static file system information. # # Use 'vol_id --uuid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # proc /proc proc defaults 0 0 # / was on /dev/mapper/minicc-root during installation UUID=1a69f02a-a049-4411-8c57-ff4ebd8bb933 / ext3 relatime,errors=remount-ro 0 1 # /boot was on /dev/sda5 during installation UUID=038498fe-1267-44c4-8788-e1354d71faf5 /boot ext2 relatime 0 2 # swap was on /dev/mapper/minicc-swap_1 during installation UUID=0bb583aa-84a8-43ef-98c4-c6cb25d20715 none swap sw 0 0 /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0 /dev/scd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0 /dev/sdb1 /mnt/sdcard auto auto,user,rw,exec 0 0 My thumb drive partition shows up as /dev/sdb1. I'm pretty sure my fstab is set up OK, but everyone on the other posts seems to fail to mention how they actually call the 'mount' command once this entry is in the fstab file. I think this is where my problem may be. The command I use to mount the drive is: $ mount /dev/sdb1 /mnt/sdcard. /bin/mount is owned by root and is in the root group and has 4755 permissions. /bin/umount is owned by root and is in the root group and has 4755 permissions. /mnt/sdcard is owned by me and is in one of my groups and has 0755 permissions. My mount command works fine if I use sudo, but I need to be able to do this without sudo (need to be able to do it from a PHP script using shell_exec). Any suggestions? Sorry for making you read so much...just trying to get as much info in the initial post as possible to preemptively answer questions about configuration stuff. If I missed anything tho, ask away. Thanks! -Travis

  Read the article

• Excel on Mac Mini OS X Version 10.7.2 - Create text file named after a cell containing other cell data from other cells

  - by user143041

  I tried using the code below for the Excel program on my `Mac Mini using the OS X Version 10.7.2 and it keeps saying Error due to file name / path: (The Excel fiel I am creating is going to be a template with my formulas and macros installed which will be used over and over). Sub CreateFile() Do While Not IsEmpty(ActiveCell.Offset(0, 1)) MyFile = ActiveCell.Value & ".txt" fnum = FreeFile() Open MyFile For Output As fnum Print #fnum, ActiveCell.Offset(0, 1) & " " & ActiveCell.Offset(0, 2) Close #fnum ActiveCell.Offset(1, 0).Select Loop End Sub What Im trying to do: 1st Objective I would like to have the following data to be used to create a text file. A:A is what I need the name of the file to be. B:2 is the content I need in the text file. So, A2 - "repair-video-game-Glassboro-NJ-08028.txt" is the file name and B2 to be the content in the file. Next, A3 is the file name and B3 is the content for the file, etc. ONCE the content reads what is in cell A16 and B16 (length will vary), the file creation should stop, if not then I can delete the additional files created. This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? 2nd Objective I would like to have the following data to be used to create a text file. A:1 is what I need the name of the file to be. B:B is the content I want in the file. So, A2 - is the file name "geo-sitemap.xml" and B:B to be the content in the file (ignore the .xml file extension in the photo). ONCE the content cell reads what is in cell "B16" (length will vary), the file creation should stop, if not then I can adjust the cells that have need content (formulated content you see in the image is preset for 500 rows). This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? I can Provide the content in the cells that are filled in by excel formulas that are not not to be included in the .txt files. It is ok if it is not possible. I can delete the extra cells that are not populated (based on the data sheet). Please let me know if you need any more additional information or clarity and I will be happy to provide it. I really appreciate your help! Thank you

  Read the article

• An alternative to Google Talk, AIM, MSN, et al [closed]

  - by mkaito

  I'm not entirely sure whether this part of stack exchange is the most adequate for my question, but it would seem to me that people sharing this kind of concern would converge either here, or possibly on a more unix-specific sub site. Either way, here goes. Background Feel free to skip to The Question, below. This should, however, help those interested understand where I'm coming from, and where I expect to get, messaging-wise. My online talking place-to-go has been IRC for the last fifteen years. I think it's a great protocol, and clients out there are very good. I still use, and will always continue to use IRC for most of my chat needs. But then, there is private instant messaging. While IRC can solve this with queries and DCC chats, the protocol just isn't meant to work too well on intermittent connections, such as a mobile device, where you can often walk around places with low signal. I used MSN for a while, but didn't like it. The concept was awesome, but I think Microsoft didn't get the implementation quite right. When they started adding all that eye candy, and my buddies started flooding me with custom icons and buzzing my screen to it's knees, I shut my account and told folks that missed me to just email or call me. Much whining happened, I got called many weird things for not using MSN, but folks eventually got over it. Next, Google Talk came along, and seemed to be a lot better than MSN ever was. The protocol was open, so I could use whatever client I felt a fancy for. With the advent of smart phones, I just got myself a gtalk client on the phone, and have had a really decent integrated mostly-universal IM solution. Over the last few months, all Google services have been feeling flaky. IMs will often arrive anywhere between twenty minutes and one hour after being sent, clients will randomly disconnect, client priorities seem to work sometimes, and sometimes just a random device of those connected will get an IM. I think the time has come to look for greener grass. The Question It's rather hard to put what I'm looking for into precise words. I guess I just want something that is kind of like MSN/Gtalk, but that doesn't let me down when I need it. IRC is pretty much perfect, but the protocol just isn't designed to work well on mobile devices. Really, at this point I'm considering sticking to IRC for desktop messaging, and SMS/email on the phone, but I hope that in this day and age there is something better out there.

  Read the article

• MySQL daemon keeps terminating unexpectedly

  - by Yehia A.Salam

  The MySQL daemon on my CentOS server keeps crashing, i got the logs from /var/logs/mysqld but still i am not sure how to fix this: 121114 16:22:56 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended 121114 21:55:11 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 121114 21:55:11 [Note] Plugin 'FEDERATED' is disabled. 121114 21:55:11 InnoDB: The InnoDB memory heap is disabled 121114 21:55:11 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121114 21:55:11 InnoDB: Compressed tables use zlib 1.2.3 121114 21:55:11 InnoDB: Using Linux native AIO 121114 21:55:11 InnoDB: Initializing buffer pool, size = 128.0M 121114 21:55:11 InnoDB: Completed initialization of buffer pool 121114 21:55:11 InnoDB: highest supported file format is Barracuda. InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 121114 21:55:11 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 121114 21:55:12 InnoDB: Waiting for the background threads to start 121114 21:55:13 InnoDB: 1.1.6 started; log sequence number 77177262 121114 21:55:13 [Note] Event Scheduler: Loaded 0 events 121114 21:55:13 [Note] /usr/libexec/mysqld: ready for connections. Version: '5.5.12' socket: '/var/lib/mysql/mysql.sock' port: 3306 MySQL Community Server (GPL) by Remi 121115 00:19:44 mysqld_safe Number of processes running now: 0 121115 00:19:44 mysqld_safe mysqld restarted 121115 0:19:47 [Note] Plugin 'FEDERATED' is disabled. 121115 0:19:47 InnoDB: The InnoDB memory heap is disabled 121115 0:19:47 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121115 0:19:47 InnoDB: Compressed tables use zlib 1.2.3 121115 0:19:47 InnoDB: Using Linux native AIO 121115 0:19:47 InnoDB: Initializing buffer pool, size = 128.0M InnoDB: mmap(137363456 bytes) failed; errno 12 121115 0:19:47 InnoDB: Completed initialization of buffer pool 121115 0:19:47 InnoDB: Fatal error: cannot allocate memory for the buffer pool 121115 0:19:47 [ERROR] Plugin 'InnoDB' init function returned error. 121115 0:19:47 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 121115 0:19:47 [ERROR] Unknown/unsupported storage engine: InnoDB 121115 0:19:47 [ERROR] Aborting Edit #1 total used free shared buffers cached Mem: 496 370 126 0 24 110 -/+ buffers/cache: 234 261 Swap: 1023 9 1014 Edit #2 Also, largest table in my mysql is 20MB, so my the memory used should be pretty moderate. SELECT CONCAT(table_schema, '.', table_name), CONCAT(ROUND(table_rows / 1000000, 2), 'M') rows, CONCAT(ROUND(data_length / ( 1024 * 1024 * 1024 ), 2), 'G') DATA, CONCAT(ROUND(index_length / ( 1024 * 1024 * 1024 ), 2), 'G') idx, CONCAT(ROUND(( data_length + index_length ) / ( 1024 * 1024 * 1024 ), 2), 'G') total_size, ROUND(index_length / data_length, 2) idxfrac FROM information_schema.TABLES ORDER BY data_length + index_length DESC LIMIT 10;

  Read the article

• Rails 3 shows 404 error instead of index.html (nginx + unicorn)

  - by Miko

  I have an index.html in public/ that should be loading by default but instead I get a 404 error when I try to access http://example.com/ The page you were looking for doesn't exist. You may have mistyped the address or the page may have moved. This has something to do with nginx and unicorn which I am using to power Rails 3 When take unicorn out of the nginx configuration file, the problem goes away and index.html loads just fine. Here is my nginx configuration file: upstream unicorn { server unix:/tmp/.sock fail_timeout=0; } server { server_name example.com; root /www/example.com/current/public; index index.html; keepalive_timeout 5; location / { try_files $uri @unicorn; } location @unicorn { proxy_pass http://unicorn; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_redirect off; } } My config/routes.rb is pretty much empty: Advertise::Application.routes.draw do |map| resources :users end The index.html file is located in public/index.html and it loads fine if I request it directly: http://example.com/index.html To reiterate, when I remove all references to unicorn from the nginx conf, index.html loads without any problems, I have a hard time understanding why this occurs because nginx should be trying to load that file on its own by default. -- Here is the error stack from production.log: Started GET "/" for 68.107.80.21 at 2010-08-08 12:06:29 -0700 Processing by HomeController#index as HTML Completed in 1ms ActionView::MissingTemplate (Missing template home/index with {:handlers=>[:erb, :rjs, :builder, :rhtml, :rxml, :haml], :formats=>[:html], :locale=>[:en, :en]} in view paths "/www/example.com/releases/20100808170224/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/paperclip/app/views", "/www/example.com/releases/20100808170224/vendor/plugins/haml/app/views"): /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/paths.rb:14:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/lookup_context.rb:79:in `find' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/base.rb:186:in `find_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:45:in `_determine_template' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/actionpack-3.0.0.beta4/lib/action_view/render/rendering.rb:23:in `render' /usr/local/rvm/gems/ruby-1.9.2-rc2/gems/haml-3.0.15/lib/haml/helpers/action_view_mods.rb:13:in `render_with_haml' etc... -- nginx error log for this virtualhost comes up empty: 2010/08/08 12:40:22 [info] 3118#0: *1 client 68.107.80.21 closed keepalive connection My guess is unicorn is intercepting the request to index.html before nginx gets to process it.

  Read the article

• Nameserver not resolving or domain not pingable [closed]

  - by Ricky

  Sorry, if anyone can think of a better title please change it! I want to host my own websites from home. For testing purposes, I have a virtual machine running a trial version of Windows Server 2008 Enterprise. Note I currently run a VPS and host my own websites but due to a nice speed upgrade on our line I now want to host from home. I have several domains but I wanted to test with one, that is rickyoleary.com. Our ISP does not provide static IP addresses unless we have a business account so I've been looking at no-ip.com. I admit my networking isn't the best, hence this question but I've been bashing my head all day on this one. I created a host name, muffinbubble.no-ip.org which runs on IP: 86.148.124.15. I've setup IIS on the server with a simple test page. I've then forwarded port 80 traffic from the router and from what I can see, it's working. If I access my website (I was unable to link to this for some reason so please copy and paste this) - http://86.148.124.15/ - I see my test page. So the next step was to create my nameservers. This domain is with namecheap.com so I created my nameservers, ns1.rickyoleary.com and ns2.rickyoleary.com. Both these point to the same IP (and yes, that will be changed after testing), the same IP as above: 86.148.124.15. On the server itself I have set up DNS entries as below which I believe to be correct and added rickyoleary.com and www.rickyoleary.com in the host headers (or bindings) in IIS 7.0. If I try and look up my domain, rickyoleary.com it shows ns1.rickyoleary.com and ns2.rickyoleary.com as the nameservers. I then tried to use just-ping.com on my nameserver ns1.rickyoleary.com. I get 100% packets lost, but the correct IP address is returned (I'm guessing the router does not allow pings, but is still accessible...). I get no response when pinging rickyoleary.com. Here's the problems: I cannot ping ns1.rickyoleary.com or ns2.rickyoleary.com from a command prompt. I'm not sure if this is an issue. When I added the nameservers in Windows Server 2008 and clicked 'resolve' a message box displays stating "No such host is known". I cannot ping rickyoleary.com. rickyoleary.com is not showing my test page on my server. Now - please note, I've waited around 6 hours for propagation. From my experience, although you're told to wait 24 - 48 hours, the changes are normally pretty quick so perhaps I'm being impatient or naive to think it should all be working fine until then. I would really appreciate some help here. Thanks.

  Read the article

• Need to increase nginx throughput to an upstream unix socket -- linux kernel tuning?

  - by Ben Lee

  I am running an nginx server that acts as a proxy to an upstream unix socket, like this: upstream app_server { server unix:/tmp/app.sock fail_timeout=0; } server { listen ###.###.###.###; server_name whatever.server; root /web/root; try_files $uri @app; location @app { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto $scheme; proxy_set_header Host $http_host; proxy_redirect off; proxy_pass http://app_server; } } Some app server processes, in turn, pull requests off /tmp/app.sock as they become available. The particular app server in use here is Unicorn, but I don't think that's relevant to this question. The issue is, it just seems that past a certain amount of load, nginx can't get requests through the socket at a fast enough rate. It doesn't matter how many app server processes I set up, it doesn't even matter what the app is (tried it with a dummy app with just a single endpoint that returned an empty page with status 404). The bottleneck seems to be the socket, not the app. I'm getting a flood of these messages in the nginx error log: connect() to unix:/tmp/app.sock failed (11: Resource temporarily unavailable) while connecting to upstream Many requests result in status code 502, and those that don't take a long time to complete. The nginx write queue stat hovers around 1000. Anyway, I feel like I'm missing something obvious here, because this particular configuration of nginx and app server is pretty common, especially with Unicorn (it's the recommended method in fact). Are there any linux kernel options that needs to be set, or something in nginx? Any ideas about how to increase the throughput to the upstream socket? Something that I'm clearly doing wrong? Additional information on the environment: $ uname -a Linux app1 3.2.0-24-generic #39-Ubuntu SMP Mon May 21 16:52:17 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux $ ruby -v ruby 1.9.3p194 (2012-04-20 revision 35410) [x86_64-linux] $ unicorn -v unicorn v4.3.1 $ nginx -V nginx version: nginx/1.2.1 built by gcc 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) TLS SNI support enabled Current kernel tweaks: net.core.rmem_default = 65536 net.core.wmem_default = 65536 net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 net.ipv4.tcp_mem = 16777216 16777216 16777216 net.ipv4.tcp_window_scaling = 1 net.ipv4.route.flush = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_moderate_rcvbuf = 1 net.core.somaxconn = 8192 net.netfilter.nf_conntrack_max = 131072

  Read the article

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• Elasticsearch won't start anymore

  - by Oleander

  I restarted my elasticsearch instance 5 days ago and I haven't manage to start it since then. I get no output in the log file /var/log/elasticsearch/ nor does the elasticsearch binary print any information when running at using elasticsearch -f. I once manage to get this output. [2012-11-15 22:51:18,427][INFO ][node ] [Piper] {0.19.11}[29584]: initializing ... [2012-11-15 22:51:18,433][INFO ][plugins ] [Piper] loaded [], sites [] Running curl http://localhost:9200 resulted in curl: (7) couldn't connect to host. I've tried increasing the memory from 3gb to 10gb, but that didn't make any diffrence. Running /etc/init.d/elasticsearch start takes 30 seconds. ps aux | grep elasticsearch results in this output. /usr/local/share/elasticsearch/bin/service/exec/elasticsearch-linux-x86-64 /usr/local/share/elasticsearch/bin/service/elasticsearch.conf wrapper.syslog.ident=elasticsearch wrapper.pidfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.pid wrapper.name=elasticsearch wrapper.displayname=ElasticSearch wrapper.daemonize=TRUE wrapper.statusfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.status wrapper.java.statusfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.java.status wrapper.script.version=3.5.14 /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/java -Delasticsearch-service -Des.path.home=/usr/local/share/elasticsearch -Xss256k -XX:+UseParNewGC -XX:+UseConcMarkSweepGC -XX:CMSInitiatingOccupancyFraction=75 -XX:+UseCMSInitiatingOccupancyOnly -XX:+HeapDumpOnOutOfMemoryError -Djava.awt.headless=true -Xms1024m -Xmx1024m -Djava.library.path=/usr/local/share/elasticsearch/bin/service/lib -classpath /usr/local/share/elasticsearch/bin/service/lib/wrapper.jar:/usr/local/share/elasticsearch/lib/elasticsearch-0.19.11.jar:/usr/local/share/elasticsearch/lib/elasticsearch-0.19.11.jar:/usr/local/share/elasticsearch/lib/jna-3.3.0.jar:/usr/local/share/elasticsearch/lib/log4j-1.2.17.jar:/usr/local/share/elasticsearch/lib/lucene-analyzers-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-core-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-highlighter-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-memory-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-queries-3.6.1.jar:/usr/local/share/elasticsearch/lib/snappy-java-1.0.4.1.jar:/usr/local/share/elasticsearch/lib/sigar/sigar-1.6.4.jar -Dwrapper.key=k7r81VpK3_Bb3N_5 -Dwrapper.port=32000 -Dwrapper.jvm.port.min=31000 -Dwrapper.jvm.port.max=31999 -Dwrapper.disable_console_input=TRUE -Dwrapper.pid=23888 -Dwrapper.version=3.5.14 -Dwrapper.native_library=wrapper -Dwrapper.service=TRUE -Dwrapper.cpu.timeout=10 -Dwrapper.jvmid=1 org.tanukisoftware.wrapper.WrapperSimpleApp org.elasticsearch.bootstrap.ElasticSearchF My current system: ElasticSearch Version: 0.19.11, JVM: 23.2-b09 Ubuntu 12.04 LTS I've tried re-install elasticsearch, removing old directories. Why can't I get it to start?

  Read the article

• EC2 Filesystem / Files stored on the wrong partiton after launching new instance from AMI

  - by Philip Isaacs

  Today I set up a new EC2 Instance from and AMI I created from an older EC2 instance. When I launched the new instance I took the AMI that was on a small instance and launched with a medium instance. From what I can tell this is pretty standard stuff. But here's the stang part. According to AWS these are the differences Small Instance (Default) 1.7 GB of memory, 1 EC2 Compute Unit (1 virtual core with 1 EC2 Compute Unit), 160 GB of local instance storage, 32-bit or 64-bit platform Medium Instance 3.75 GB of memory, 2 EC2 Compute Units (1 virtual core with 2 EC2 Compute Units each), 410 GB of local instance storage, 32-bit or 64-bit platform Okay now here's where I'm having an issue. I when I log into the new bigger instance it still reports only having 1.7 GB of ram. The other strange part is that all my old partitions are still their in the same configurations. I see a new larger partition /mnt which is essential empty. Filesystem Size Used Avail Use% Mounted on /dev/sda1 7.9G 5.9G 1.6G 79% / none 846M 120K 846M 1% /dev none 879M 0 879M 0% /dev/shm none 879M 76K 878M 1% /var/run none 879M 0 879M 0% /var/lock none 879M 0 879M 0% /lib/init/rw /dev/sda2 335G 195M 318G 1% /mnt /dev/sdf 16G 9.9G 5.1G 67% /var2 This EC2 is a web server and I was serving files off the /var2 directory but for some reason the instance is storing everything on / Okay here's what I'd like to do. Move all my website files to /mnt and have the web server point to that. Any suggestions? If it helps here is what my fstab looks like as well. root@myserver:/var# mount -l /dev/sda1 on / type ext3 (rw) [cloudimg-rootfs] proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) none on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) /dev/sda2 on /mnt type ext3 (rw) /dev/sdf on /var2 type ext4 (rw,noatime) I hope this question makes sense. Basically i want my old files on this new partition. Thanks in advance

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• Linux Mint 14 severe overheating

  - by agvares

  I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

  Read the article

• Server load spikes several times a day, load average for the past month is 5 times the load average all year

  - by AMF

  My Munin notifications set up for our (Debian) LAMP cluster have been notifying me continuously that our load on our production machine has been at dangerous levels. While the average load all year typically runs between 2 and 8, the load in the past month and only the past month -- has been skyrocketing to 10, 18, and occasionally even 50-60. The spikes last only 5-10 minutes at a time and occur about every 2-3 hours. The spikes do not effect performance only because I have a script that sends traffic off our server to a mirror CDN when the load goes above 10. I've looked for cron jobs that correlate with this timeframe but there is nothing I can see that would cause this. Site traffic is also normal (we receive about 200K visits per day). I'm also trying to think of anything I've changed around the time this problem began, and I really cannot think of anything. This is probably not much to go on. Maybe there is a clue in the top print-out (below) that I'm not seeing. How do I proceed to find the cause? -- Typical top when the load is NOT spiking: top - 11:13:09 up 472 days, 25 min, 1 user, load average: 6.08, 4.29, 3.80 Tasks: 105 total, 1 running, 104 sleeping, 0 stopped, 0 zombie Cpu(s): 41.2%us, 5.8%sy, 0.0%ni, 49.5%id, 2.7%wa, 0.1%hi, 0.7%si, 0.0%st Mem: 3369592k total, 2166980k used, 1202612k free, 559504k buffers Swap: 2650684k total, 1892k used, 2648792k free, 1129116k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 32046 apache 15 0 36300 12m 9828 S 20 0.4 0:01.97 apache2 32679 apache 15 0 36568 13m 10m S 19 0.4 0:01.69 apache2 31441 apache 15 0 36616 13m 10m S 19 0.4 0:04.13 apache2 31477 apache 15 0 36596 13m 9.8m S 15 0.4 0:01.99 apache2 31993 apache 15 0 36876 16m 12m S 12 0.5 0:02.01 apache2 31782 apache 15 0 36836 14m 10m S 8 0.4 0:02.17 apache2 32198 apache 15 0 36536 13m 10m S 7 0.4 0:01.59 apache2 880 apache 15 0 36508 9708 6236 S 7 0.3 0:00.42 apache2 31945 apache 17 0 36876 16m 13m S 5 0.5 0:03.17 apache2 32197 apache 16 0 36636 10m 7504 S 5 0.3 0:02.70 apache2 32326 apache 15 0 37024 11m 7632 S 5 0.3 0:02.15 apache2 32565 apache 15 0 37280 13m 9.8m S 5 0.4 0:03.75 apache2 32676 apache 15 0 36896 16m 12m S 4 0.5 0:00.95 apache2 32678 apache 15 0 36536 12m 9692 S 4 0.4 0:02.27 apache2 974 apache 16 0 37064 9888 6016 D 4 0.3 0:00.13 apache2 32150 apache 16 0 36832 13m 10m S 3 0.4 0:01.74 apache2 31780 apache 16 0 36848 11m 7660 S 3 0.3 0:02.87 apache2

  Read the article

• How to configure nginx so it works with Express?

  - by Michal Stefanow

  I'm trying to configure nginx so it proxy_pass requests to my node apps. Question on StackOverflow got many upvotes: http://stackoverflow.com/questions/5009324/node-js-nginx-and-now and I'm using config from there. (but since question is about server configuration it is supposed to be on ServerFault) Here is the nginx configuration: server { listen 80; listen [::]:80; root /var/www/services.stefanow.net/public_html; index index.html index.htm; server_name services.stefanow.net; location / { try_files $uri $uri/ =404; } location /test-express { proxy_pass http://127.0.0.1:3002; } location /test-http { proxy_pass http://127.0.0.1:3003; } } Using plain node: var http = require('http'); http.createServer(function (req, res) { res.writeHead(200, {'Content-Type': 'text/plain'}); res.end('Hello World\n'); }).listen(3003, '127.0.0.1'); console.log('Server running at http://127.0.0.1:3003/'); It works! Check: http://services.stefanow.net/test-http Using express: var express = require('express'); var app = express(); // app.get('/', function(req, res) { res.redirect('/index.html'); }); app.get('/index.html', function(req, res) { res.send("blah blah index.html"); }); app.listen(3002, "127.0.0.1"); console.log('Server running at http://127.0.0.1:3002/'); It doesn't work :( See: http://services.stefanow.net/test-express I know that something is going on. a) test-express is NOT running b) text-express is running (and I can confirm it is running via command line while ssh on the server) root@stefanow:~# service nginx restart * Restarting nginx nginx [ OK ] root@stefanow:~# curl localhost:3002 Moved Temporarily. Redirecting to /index.html root@stefanow:~# curl localhost:3002/index.html blah blah index.html I tried setting headers as described here: http://www.nginxtips.com/how-to-setup-nginx-as-proxy-for-nodejs/ (still doesn't work) proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-NginX-Proxy true; I also tried replacing '127.0.0.1' with 'localhost' and vice versa Please advise. I'm pretty sure I miss some obvious detail and I would like to learn more. Thank you.

  Read the article

• PHP & MySQL on Mac OS X: Access denied for GUI user

  - by Eirik Lillebo

  Hey! This question was first posted to Stack Overflow, but as it is perhaps just as much a server issue I though it might be just as well to post it here also. I have just installed and configured Apache, MySQL, PHP and phpMyAdmin on my Macbook in order to have a local development environment. But after I moved one of my projects over to the local server I get a weird MySQL error from one of my calls to mysql_query(): Access denied for user '_securityagent'@'localhost' (using password: NO) First of all, the query I'm sending to MySQL is all valid, and I've even testet it through phpMyAdmin with perfect result. Secondly, the error message only happens here while I have at least 4 other mysql connections and queries per page. This call to mysql_query() happens at the end of a really long function that handles data for newly created or modified articles. This basically what it does: Collect all the data from article form (title, content, dates, etc..) Validate collected data Connect to database Dynamically build SQL query based on validated article data Send query to database before closing the connection Pretty basic, I know. I did not recognize the username "_securityagent" so after a quick search I came across this from and article at Apple's Developer Connection talking about some random bug: Mac OS X's security infrastructure gets around this problem by running its GUI code as a special user, "_securityagent". Then I tried put a var_dump() on all variables used in the mysql_connect() call, and every time it returns the correct values (where username is not "_securityagent" of course). Thus I'm wondering if anyone has any idea why 'securityagent' is trying to connect to my database - and how I can keep this error from occurring when I call mysql_query(). Update: Here is the exact code I'm using to connect to the database. But a little explanation must follow: The connection error happens at a call to mysql_query() in function X in class_1 class_1 uses class_2 to connect to database class_2 reads a config file with the database connection variables (host, user, pass, db) class_2 connect to the database through the following function: var $SYSTEM_DB_HOST = ""; function connect_db() { // Reads the config file include('system_config.php'); if (!($SYSTEM_DB_HOST == "")) { mysql_connect($SYSTEM_DB_HOST, $SYSTEM_DB_USER, $SYSTEM_DB_PASS); @mysql_select_db($SYSTEM_DB); return true; } else { return false; } }

  Read the article

• Setting up a very mixed Active Directory network to work with PowerShell Remote Administration

  - by erictheavg

  Summary: I want to be able to monitor the computers on my network, but don't need it to be automated. We're too small to purchase anything like MOM, but too big to do anything manually (~100 machines in two locations). I just keep running into issues, and was wondering if there's a master list of Group Policy settings I can distribute to my environment to get Remote Powershell working. Environment: Our AD network is pretty mixed. The end users have XP SP3, Win 7, and Win 7 x64. The servers include Win2k3 SP2, Win2k8, Win2k8 x64, Win2k8 R2, and Win2k8 R2 x64. Details: I'm trying to get it to work with Remote Powershell, but I run into errors like the following: Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Default authentication may be used with an IP address under the following conditions: the transport is HTTPS or the destination is in the TrustedHosts list, and explicit credentials are provided. Use winrm.cmd to configure TrustedHosts. Note that computers in the TrustedHosts list might not be authenticated. For more information on how to set TrustedHosts run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. + CategoryInfo : OpenError: (:) [], PSRemotingTransportException + FullyQualifiedErrorId : PSSessionStateBroken Then I go to the computer (Win2k3 SP2 server) and run winrm quickconfig per the recommendations via google, and it says: Make these changes [y/n]? y WinRM has been updated to receive requests. WinRM service started. WSManFault Message = The client cannot connect to the destination specified in the request. Verify that the service on the destination is running and is accepting requests. Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or WinRM. If the destination is the WinRM service, run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". Error number: -2144108526 0x80338012 The client cannot connect to the destination specified in the request. Verify that the service on the destination is running and is accepting requests. Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or WinRM. If the destination is the WinRM service, run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". That's right. It tells me to remedy my winrm quickconfig failure by running winrm quickconfig. I don't want to band-aid this project one google search at a time. I'm sure there is a step-by-step tutorial out there on how to set up a network for powershell remote administration. Does anyone know of one? Books are acceptable. Thanks in advance! I didn't think my question would get this long.

  Read the article

• Ubuntu server 10.04 doesn't boot into installed Gnome desktop automatically

  - by Tong Wang

  I've installed Ubuntu server 10.04 and then installed Gnome desktop on top of it, because I am new to Linux and its command line, I need the GUI desktop to help me get around. However, the problem I got is that the server doesn't boot into the GUI desktop when powered on. It's booting into a shell like this: Gave up waiting for root device. Common problems: - Boot args (cat /proc/cmdline) - Check rootdelay= (did the system wait long enought?) - check root= (did the system wait for the right device?) - Missing modules (cat /proc/modules; ls /dev) ALERT! /dev/mapper/cecdata-root does not exist. Dropping to a shell! BusyBox v1.13.3 (Ubuntu 1:1.13.3-1ubuntu11) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) result of (cat /proc/cmdline) BOOT_IMAGE=/vmlinuz-2.6.32-28-server root=/dev/mapper/cecdata-root ro quiet Then I have type "exit" to exit the shell and then it boots into Gnome. Any idea what's wrong? Edit: add output for the following commands wt@cecdata:~$ ls /dev/mapper/ cecdata-root cecdata-swap_1 control wt@cecdata:~$ fdisk -l wt@cecdata:~$ wt@cecdata:~$ cat /etc/fstab # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/cecdata-root / ext4 errors=remount-ro 0 1 # /boot was on /dev/sda1 during installation UUID=1635be41-d025-405e-b4a3-6f0abedb7aab /boot ext2 defaults 0 2 /dev/mapper/cecdata-swap_1 none swap sw 0 0 wt@cecdata:~$ Adding output for lsmod wt@cecdata:~$ lsmod Module Size Used by fbcon 39270 71 tileblit 2487 1 fbcon font 8053 1 fbcon bitblit 5811 1 fbcon softcursor 1565 1 bitblit dell_wmi 2177 0 dcdbas 6918 0 vga16fb 12757 1 vgastate 9857 1 vga16fb psmouse 64576 0 serio_raw 4950 0 power_meter 9473 0 bnx2 72874 0 lp 9336 0 parport 37160 1 lp mptsas 50592 2 usbhid 41116 0 mptscsih 37167 1 mptsas hid 83568 1 usbhid mptbase 91674 2 mptsas,mptscsih scsi_transport_sas 33021 1 mptsas

  Read the article

• iftop Shows Lots of Mysterious Connections - Not Showing in netstat

  - by HOLOGRAPHICpizza

  I've just stopped all pretty much all services except sshd on my server (Ubuntu Server 10.04), and when I run iftop I get output that looks like this: 12.5Kb 25.0Kb 37.5Kb 50.0Kb 62.5Kb mqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqq flash.gateway.2wire.net:ssh <=> 172.16.1.151:60405 1.75Kb 1.54Kb 2.22Kb flash.gateway.2wire.net:21095 <=> 69.127.29.20:32582 536b 107b 27b flash.gateway.2wire.net:21095 <=> 190.164.122.134:13557 0b 105b 26b flash.gateway.2wire.net:21095 <=> 79.165.212.195:45138 0b 105b 26b flash.gateway.2wire.net:21095 <=> 151.42.15.151:9031 0b 72b 18b flash.gateway.2wire.net:21095 <=> 88.185.120.179:51413 0b 0b 49b flash.gateway.2wire.net:21095 <=> 178.120.152.97:25924 0b 0b 29b flash.gateway.2wire.net:21095 <=> 109.110.217.77:27868 0b 0b 26b flash.gateway.2wire.net:21095 <=> 84.13.201.90:16509 0b 0b 26b flash.gateway.2wire.net:21095 <=> 171.7.125.224:11777 0b 0b 26b flash.gateway.2wire.net:21095 <=> 115.177.164.170:21360 0b 0b 26b flash.gateway.2wire.net:21095 <=> 50.88.126.18:25540 0b 0b 25b flash.gateway.2wire.net:21095 <=> 223.206.230.163:13431 0b 0b 25b flash.gateway.2wire.net:21095 <=> 78.144.187.26:24515 0b 0b 25b flash.gateway.2wire.net:21095 <=> 83.20.61.211:27572 0b 0b 25b flash.gateway.2wire.net:21095 <=> 82.134.151.42:18448 0b 0b 18b flash.gateway.2wire.net:21095 <=> 126.117.95.247:25316 0b 0b 18b flash.gateway.2wire.net:21095 <=> 116.202.65.230:9044 0b 0b 18b flash.gateway.2wire.net:21095 <=> 88.120.63.205:51413 0b 0b 17b qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cumm: 61.6KB peak: 8.00Kb rates: 1.59Kb 1.38Kb 2.04Kb RX: 18.4KB 1.64Kb 696b 549b 640b TOTAL: 80.0KB 9.64Kb 2.27Kb 1.92Kb 2.66Kb This is the first part (not the unix socket part) of the output of netstat -a: Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:55677 *:* LISTEN tcp 0 0 flash.gateway.2wire:ssh 172.16.1.151:60405 ESTABLISHED tcp 0 48 flash.gateway.2wire:ssh 172.16.1.151:60661 ESTABLISHED tcp6 0 0 [::]:ssh [::]:* LISTEN udp 0 0 *:37790 *:* What could all those strange connections on port 21095 be? And why would they not show up in netstat?? Any advice would be greatly appreciated.

  Read the article

• nginx - Redirect specific page paths to https while keeping everything else on http (in a single server call)?

  - by Kris Anderson

  From what I've gathered so far it's clear that running if statements in nginx should be avoided at all costs. Most of the examples I've found so far regarding specific page redirects involve multiple servers being used. But, isn't that a bit wasteful? I'm not sure, but I would think multiple servers to accomplish this would be somewhat slower then a single server when under heavy load. My current server call is this: server { listen 10.0.0.60:80; listen 10.0.0.60:443 default ssl; #other code } What I want to do is redirect certain http requests to https requests. For example, I want /login/ and /my-account/ to always be forced to use SSL. If you're on /help/ though, I want that served over the default http. Is there a way to accomplish this within a single server call? Or is there no downside to using 2 server calls to get this working? nginx seems to be under pretty active development and a lot of the older guides I've followed were from times when you couldn't listen to requests for port 80 and 443 within the same server call. But now that nginx has been updated to support that (I'm running 1.2.4), I'm wondering if there's a "best practice" way of handling this today. Any help would be greatly appreciated. EDIT: I did find this guide: http://redant.com.au/blog/manage-ssl-redirection-in-nginx-using-maps-and-save-the-universe/ and I updated my code as follows: map $uri $my_preferred_proto { default "http"; ~^/#/user/login "https"; } server { listen 10.0.0.60:80; ## listen for ipv4; this line is default and implied listen 10.0.0.60:443 default ssl; if ($my_preferred_proto = "none") { set $my_preferred_proto $scheme; } if ($my_preferred_proto != $scheme) { return 301 $my_preferred_proto://mysite.com$request_uri; } It's not working though. When I change the default to https everything is redirected to SSL so it does somewhat work. But the redirect of /#/user/login is not redirecting to HTTPS. Any ideas? Also, is this a good way to go about this?

  Read the article

< Previous Page | 693 694 695 696 697 698 699 700 701 702 703 704  | Next Page >