Search Results

Search found 21960 results on 879 pages for 'program termination'.

Page 699/879 | < Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >

• How do I use a self encrypting drive?

  - by Unique_Key

  I recently purchased a Micron RealSSD c400 self encrypting drive, and I am having a few issues when trying to get it recognized by my laptop (HP Elitebook 8440p running Windows 7 x64; also tried on a custom-built desktop). When I try to initialize the drive from disk management, I get a CRC error; also, when attempting to partition it from Windows setup, the program can't create the partitions. I also tried with UBCD, nothing. I assume this is due to drive security, but I haven't been able to find much information about this online; do I need a management software or something? I'm completely stumped here. EDIT As requested, when I try partitioning the device from Windows setup I get a 0x80300024 error; when I try initializing it from disk management, I get a "Data error (cyclic redundancy check)" message, and the event log shows the following under System: Source: VDS Basic Provider, message: unexpected failure. error code 490@01010004 (2x) Source: Virtual Disk Service, message: VDS fails to write boot code on a disk during clean operation. Error code: 80070001@02070008 (1x) Source: Disk, message: The device \Device\Harddisk2\DR2 has a bad block (2x) The security logs show nothing related. Also, when attempting to configure it from UBCD (utility: HDAT2), I get an error along the lines of "can't edit partition information" or something to that tune.

  Read the article

• Installing GitHub for Mac - "Github cannot be opened because of a probem"

  - by betitall

  I'm trying to get started using Git for Mac, but I receive an error when I try to run the program. I'm new to GitHub and relatively new to Mac. First, I installed Git using the downloadable .dmg file named "git-1.7.12.3-intel-universal-snow-leopard". I ran the .pkg file contained therein and the install seemed to work fine. I'm using a new macbook pro w/ retina. Then I downloaded the Github for Mac installer, "mac_GitHub for Mac 69.zip". When I double-click the file, it shows that there is a single file of type "Application". Double-clicking that application file produces the error: "GitHub cannot be opened because of a problem". Here are the partial details of that error: Application Specific Information: dyld: launch, loading dependent libraries Dyld Error Message: Library not loaded: @executable_path/../Frameworks/Rebel.framework/Rebel Referenced from: /Applications/GitHub.app/Contents/MacOS/GitHub Reason: no suitable image found. Did find: /Applications/GitHub.app/Contents/MacOS/../Frameworks/Rebel.framework/Rebel: file too short /Applications/GitHub.app/Contents/MacOS/../Frameworks/Rebel.framework/Rebel: file too short Any help would be much appreciated. Thanks.

  Read the article

• Windows 7 autostarting apps as administrator

  - by Fujishiro

  Hello everyone. The question is easy to answer I guess. (Tried to search here, didn't find an answer.) So. The deal: There is a bug in OpenOffice (haha ..just one? :)), which prevents the spellcheck. You have to start it with right-click , run as administrator to make it work. Tried also setting this at the 'properties', but it didn't work. But 'quickstart.exe' would be also enough to make this work. (OpenOffice's quickstarter). So I'd like to run it at boot, as an admin, like I'd do with right-click. How to do THAT? (Actually there is a different bug for spellcheck on Win7. One have to run oowriter.exe as an admin, and then install the extension BY HAND from Program Files...\share...*.oxt. And THEN it'll work IF you run the app as an admin. (I'll buy SoftMaker's office as soon as the hu spellcheck arrives, but until then I have to make this work. Thanks for the answers in advance.))

  Read the article

• Export Outlook Express XP into Outlook 2007 Windows 7

  - by Jason Moore

  I've searched the forum and it seems my need is a little different than the posts which have already been made. I have an old XP laptop which I was using Outlook Express for one of my mail accounts (a work account). I also ran regular Outlook for another (personal). I want to have both of these accounts on my new PC. My new PC is running Windows 7 wiht Office 2007. I used the Windows transfer cable and things worked failry well. My regular Outlook files all came over well, but nothing for Outlook Express. I really would like to take this time to somehow export my OE files into my Outlook 2007. I would really like to keep the account which imported in on Outlook seperate. Question 1: Is there a way to import my OE files into Outlook 2007? Question 2: Is there a way to have two seperate email accounts in Outlook without combining them? Basically I want to have a work email and a personal and keep them seperate. If I can't have two seperate emails with Outlook, can anyone suggest something which would allow me to export my old Outlook (the old personal emails) into another program so that I can at least use my work email on Outlook 2007? Hopefully this isn't too confusing.

  Read the article

• keyboard intermittently stops working even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash the ctrl+alt+windows keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) Unplugging & reconnecting keyboard does NOT fix it. Connecting a different keyboard does NOT fix it. That one won't work, either. Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears the keyboard won't work and neither will the icon to pull up the on-screen keyboard. My mouse can click around just fine. I can only log onto a non-password protected account. Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. Clearing my Chrome browsing data stopped the problem from recurring for a week or so. I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. I use Avira free antivirus software, and repeated scans turn up nothing fishy. I suspect it is related to something in Google Chrome because I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• Getting a TTY in a Connectback Shell

  - by Asad R.

  I'm often asked by friends to help with small Linux problems, and more often than not I'm required to login to the remote system. Usually there are a lot of issues with making an account and logging in (sometimes the box is behind a NAT device, sometimes SSHD isn't installed, etc.) so I usually just ask them to make a connect-back shell using netcat (nc -e /bin/bash ). If they don't have netcat I can just ask them to grab a copy of a statically compiled binary which isn't that hard or time consuming to download and run. Though this works well enough for me to enter simple commands, I can't run any apps that require a tty (vi, for example) and can't use any job control functions. I managed to bypass this issue by running in.telnetd with a few arguments within the connect-back shell that would assign me a terminal and drop me to a shell. Unfortunately in.telnetd isn't usually installed by default on most systems. What's the easiest way to get a fully functional connect-back terminal shell without requiring any non-standard packages? (A small C program that does the job would be fine as well, I just can't seem to find much documentation on how a TTY is assigned/allocated. A solution that doesn't require me to plough through the source code for SSHD and TELNETD would be nice :))

  Read the article

• Word 2007 textbox management

  - by TheSavo

  I am updating a user manual that was initially written by somebody else. I know that most manuals are not written in Word, but our office only uses Microsoft Office applications. I am doing fairly well, creating and applying "styles". A lot of the directions in this manual require updated screenshots of the program it documents. … It's a big mess. </rant> One thing I am attempting to do is add “call outs” or Note text boxes like those seen in modern software manuals. I am attempting to do this with the Text box feature. However, I am having a hard time making them uniform in size and positioning. Does Word offer a way to manage the size and other properties of textboxes, similar to the way it allows you to manage text in styles? I feel that this could (or should) be possible. Is it possible to manage Text Boxes the same way you can manage styles?

  Read the article

• Multi-select menu in bash script

  - by am2605

  I'm a bash newbie but I would like to create a script in which I'd like to allow the user to select multiple options from a list of options. Essentially what I would like is something similar to the example below: #!/bin/bash OPTIONS="Hello Quit" select opt in $OPTIONS; do if [ "$opt" = "Quit" ]; then echo done exit elif [ "$opt" = "Hello" ]; then echo Hello World else clear echo bad option fi done (sourced from http://www.faqs.org/docs/Linux-HOWTO/Bash-Prog-Intro-HOWTO.html#ss9.1) However my script would have more options, and I'd like to allow multiples to be selected. So somethig like this: 1) Option 1 2) Option 2 3) Option 3 4) Option 4 5) Done Having feedback on the ones they have selected would also be great, eg plus signs next to ones they ahve already selected. Eg if you select "1" I'd like to page to clear and reprint: 1) Option 1 + 2) Option 2 3) Option 3 4) Option 4 5) Done Then if you select "3": 1) Option 1 + 2) Option 2 3) Option 3 + 4) Option 4 5) Done Also, if they again selected (1) I'd like it to "deselect" the option: 1) Option 1 2) Option 2 3) Option 3 + 4) Option 4 5) Done And finally when Done is pressed I'd like a list of the ones that were selected to be displayed before the program exits, eg if the current state is: 1) Option 1 2) Option 2 + 3) Option 3 + 4) Option 4 + 5) Done Pressing 5 should print: Option 2, Option 3, Option 4 and the script terminate. So my question - is this possible in bash, and if so is anyone able to provide a code sample? Any advice would be much appreciated.

  Read the article

• Windows Vista: Screen remains darkened for 30-60 seconds *after* UAC prompt

  - by sf2k

  Fixing someone's Vista computer. Process: I click any program or process that opens a User Account Control prompt. Screen goes dim so you may hit Continue to perform a secure user action. I click Continue Screen goes black for 30 seconds to 1 minute while you wait for the screen to return. In another example I click Cancel and screen still then goes black for 30 seconds to a minute. In that timeframe a chime goes off while you wait. (No chime if it was being cancelled.) Then screen comes back to continue with whatever. Something is occurring after the UAC prompt. Considering everything is practically a UAC acceptance this can get pretty annoying pretty quickly. Laptop has external monitor to regular external plug. Works fine. Laptop also has USB IOGEAR additional external video card. This is problematic but when unplugged same above behaviour occurs. I've ruled out monitor interference since same blackout after the UAC prompt appears with external monitors plugged in or when rebooted with no external monitors. Any suggestions on how to address this problem?

  Read the article

• Windows Vista Nested Desktop Folders Problem

  - by Samuel Walker

  I have no idea how, nor when this happened, and it's started to really quite annoy me. When navigating through Explorer, by clicking on Icons I have C:\Users\Samuel\Desktop (Icon is the blue special Desktop icon), which contains the items I see on my Desktop. I then have the following folder: C:\Users\Samuel\Desktop (Icon is the standard yellow folder icon), which contains many program shortcuts, and is completely seperate from the other C:\Users\Samuel\Desktop Then in the Yellow Icon Desktop I have the sub-folder Desktop with the blue icon that is a direct mirror of the blue C:\Users\Samuel\Desktop folder (as in a new folder / file shows up in both). In explorer when I directly type C:\Users\Samuel\Desktop I am taken to the Yellow folder version. If I go to C:\Users\Samuel\Desktop\Desktop I am taken to the Blue folder version. Finally, from cmd cd'ing to C:\Users\Samuel\Desktop takes me to the Yellow folder version whilst C:\Users\Samuel\Desktop\Desktop takes me to the blue folder version. How on earth can I get rid of the yellow folder version leaving the blue C:\Users\Samuel\Desktop. I can't delete either as it says they're in use. UPDATE: Ok, so it looks like doing a dir from cmd lists only one Desktop folder - the Yellow one. In addition, it looks like I can't delete either of them (given that they both contain my 'Desktop'

  Read the article

• How to repair a damage transaction log file for Exchange 2003

  - by Markus Larsson

  Hi! Yesterday we had a power failure and the UPS did not work (it has worked perfect before). Everything seem to be ok when I started all the servers again except of the mail, when I try to mount the store I get the following message: “The database files in this store are corrupted” Server: Exchange 2003 running on a Small Business Server Latest full backup: one week old Backup program: Backup Exec 9.0 This is what I have done: 1. Copy every file in the MDBDATA folder (edb, stm, log) 2. Run Eseutil /d for priv1.edb 3. Run Eseutil /p for priv1.edb (took seven hours) 4. Run Isintig –fix –test alltests, now it breaks down. Isintig fails with the following error: Isinteg cannot initiate verification process. Please review the log file for more information. The problem is that there is no log file created. 5. Giving up on this route I decide to do a restore from the backup, it fails with the following error: Unable to read the header of logfile E00.log. Error -501, and the error: Information Store (5976) Callback function call ErrESECBRestoreComplete ended with error 0xC80001F5 The log file is damaged. My conclusion is that E00.log is damage, so how can I repair it so that I can restore the database? Or should I give up and try some other route?

  Read the article

• Samba Share - MS Excel when saved (can't access the file, there are several possible reasons)

  - by brain90

  Dear Fellow ServerFaulter, I have a weird problem in my samba share. I have one share definition for 3 client (A,B,C) This share contain some excel file which having a lot of formula and linked each other. Client A access the file with libre office (ubuntu), client B access with WinXP & MS Office 2003, The write and read process working successfuly on Both of them. The problem occur when client C accessing the same file with MS Excel 2003 (windows xp). This messagebox appear when he saving the file : Microsoft office excel cannot access the \\192.168.1.23\myshare\ There are several possible reasons: - The File ort path does not exist The file is being used by another program. - The workbook you are trying to save has the same name as a - Currently open workbooks. I was trying http://support.microsoft.com/kb/291204 but it didnt work. Below is my share definition : [brainshare] comment = brainshare path = /opt/brainshare/ valid users = @brainshare force group = brainshare read only = No create mask = 0775 veto files = /*.scr/*.eml/thumbs.com/ Help me please... Thanks in advance ! Server: Ubuntu 10.10, Samba version 3.5.4

  Read the article

• Adding network share as the system account breaks Win7 backup to network

  - by ChrisBenn

  (On Win7 Ultimate x64 SP1) So I've been using Win7 backup to \192.168.0.100\Backup\main-desktop\ for awhile without issue. Yesterday I tried to setup crashplan to synchronize my dropbox folder and a network share. I then found out that crashplan, as it runs under the system account, can't see my user mapped drives. So I created a startup script net use O: \192.168.0.100\Documents /USER:192.168.0.100\username password and set it to run, on startup, after the network interface is up, as the system account. (the username & password are the same for the net use script above, the locally logged in user, and the explicit username/password entered in windows backup). I woke up this morning to find error flags from the windows backup and get "Network location cannot be used" (0x800704B3). If I disable the startup task & reboot then windows backup works fine. I'm not sure why having a mapped drive for another user is killing windows backup (same server, different folder). I can work around the issue by using another program to synchronize the two folders, but I'm completely in the dark as to why this happens (and it's 100% repeatable). Uninstalling the crashplan client doesn't change anything - it's the net use run under the system account that breaks win7 backup (to a network location).

  Read the article

• Symantec Endpoint Protection Virus Definitions

  - by Gus Denton

  I have done some Googling but I cannot get a definitive answer certainly not from the Symantec KB. I have a Virtualised Win 2003R2 server 32bit. It has been provisioned to me with Symantec Endpoint Protection 11.0.62xxx CLIENT (not a definitions server) the directory C:\Program Files\Common Files\Symantec Shared\VirusDefs is 750MB IT doesn't contain .tmp directories so it is NOT a corrupt definitions server. IT does contain directories named with a date pattern YYYYMMDD.xxx Some of these folders are 12 months old and I would like to recover the space. The sysmantect forums are full of this stuff but a lot of the postings contain links back to documents that are not specific to End Point Protection Client. It appears that I should be able to delete the older folders and all will be OK. with a service restart however there is a warning about having Live Update Administrator Installed Firstly I have no idea if I have this installed how to I check and secondly can I just ditch these old files and restart ? Regards Gus Denton Learning and Teaching Uni of New South Wales Sydney Australia For those trying to assist me I thankyou. I have followed some instructions found on the Symantec site and assumed that the response from Nixphoe would resolve my issue. It appears that as I am on a provisioned VM from a central IT unit I cannot run the Symantec commands from the Run prompt as my admin creds to get me in. (smc -stop) Basically I need to claw back some Diskspace from the c: drive which is being filed up with WSUS patches and Symantec files. I have managed to delete one symantec cache through the live update control panel and recovered 470Mb I suppose my last question for those more experienced than myself is, can I simply remove say the two oldest virus definition folders without completely foobaring the End Point protection and the server ? Regards Gus

  Read the article

• Linux Port 80 to redirect to a Windows box

  - by Richard Staehler

  I have 2 servers here at work. One is a Windows 2008 Server R2 (for safety's sake, lets use 192.168.1.100) and the other is a Fedora 14 (192.168.1.101). Currently when you hit our subdomain, x.test.com, our routers tell it to go to our Fedora box, and since Apache is installed and listening to port 80, it displays the Fedora Apache Test Page. It's obvious that I don't use port 80 for this machine, however I do use NAGIOS on it and its always nice to be able to access that from anywhere in the world. So when I want to access it, I just type x.test.com/nagios. Now here comes the dilemma.... On the Windows R2 box, we recently have installed a program that requires us to setup a web server using IIS7. Because of this application, I'm going to be creating a new subdomain called y.test.com, but since we only have 1 WAN/router, it will still get pointed to our Fedora box. That being said, it wants to use port 80 as well (or whatever port I damn well wish to assign it). So my question is: since our router is pointing to the Fedora 14 box (.101), and I want to make sure I can access NAGIOS from anywhere in the world, how do I tell Apache (httpd) to redirect port 80 to the other server (.100)? If not possible, what are my other options? I have rinetd installed on Fedora and have even tried the option 192.168.1.101 80 192.168.1.100 80 and it didn't seem to work "because port 80 was already bound" Thoughts? and Thanks!

  Read the article

• SQL Server Installaion error 0x84B40000

  - by Kurtevich

  I have a problem installing SQL Server 2008 R2. Long time ago I had it installed, and then uninstalled. It was left in "Add/remove programs", but I didn't pay attention on that. I had 2005 installed. And now there is a need to install 2008. I removed 2005 and started installing 2008, but it says that space on C: is not enough. That's when I found out that "Add/remove programs" shows it occupying more than 4 gigabytes, though I used to uninstall it. So I click "Remove", it shows all those many screens and validations, shows that removal completed, but the size of Program Files folder is still more than 4 GB. I removed (from "Add\remove programs" everything that had "SQL Server" in it's name, but that main "SQL Server 2008" item is still there and still 4 GB and uninstalling does nothing. Because installation of SQL Server did not show existing instances, and I don't see any running services related to SQL server (well, almost any, more details in the end), I though that this folder contains just some leftover staff and data and deleted it manually. Then agreed to removing of the item in "Add/remove programs" and everything looks clean. Now every time I try to install SQL Server (even in the minimum configuration), I receive the following error: SQL Server Setup has encountered the following error: The specified credentials that were provided for the SQL Server service are not valid. To continue, provide a valid account and password for the SQL Server service. Error code 0x84B40000. What is this service mentioned here? This error looks like I'm trying to add features to existing server and it can't login. But the setup didn't ask me for any credentials, except one username that couldn't be changed. Here are the services shown that can be related, both disabled and pointing to non-existing executables: SQL Active Directory Helper Service SQL Full-text Filter Daemon Launcher (MSSQLSERVER) I understand that this must be because of my manual deletion, but is there a way to clean it up now?

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  Hi, I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• Remote desktop solution where the desktop sharing party contacts the computer it wants to share with

  - by Kent

  I'm in a situation where I act as a sort of techinical support to my family and less techinically experienced friends. I'm looking for a remote desktop solution where it's possible to setup a "zero-install, double click an icon"-solution where the client computer contacts me so that I may interact with their desktop. The last part is important as the people in need of my help don't know how to configure their router or even the firewall software on their own computer. They are able to click an accept button when asked if a program should be able to make outgoing connections. They have many different kinds of routers, as well as software firewalls, and I rather not deal with the problem of how to connect to them using whatever as well as the actual problem they are having. It must be: Free of charge for non-commercial use. Possible to use it in a mode where the computer wanting to share its desktop should be able to make a connection to my computer. My computer has a DNS name we can use. Compatible with both Windows XP and Windows 7. Independent of a third party server or infrastructure. Explanations of the above: I don't want to spend money on it when I help them for free. If it's free as in freedom, all the better! I guess this boils down to being callable like showdesktopto.exe opscomputer.com where opscomputer.com is my computers DNS name. If that is possible then I can create a shortcut they can use to connect to me when they need help. It's nice if it's possible to specify a password or key file which I can use to authenticate myself, but it's not required. They use the OS which their machine comes installed with. That means Windows XP or 7. I want something which will work in the long run. Using a third party service which might not be available when I need it disqualified such solutions.

  Read the article

• PORT FORWARDING TO PUT MY WEB SERVER ON THE INTERNET

  - by Chadworthington

  I went to http://canyouseeme.org/ to check to see what my external IP address. Regardless of what port I enter, it tells me that the port is blocked. I have a LinkSys router that basically has the default settings with the exception that I have WEP encrptin setup and I have forwarded a few ports, including 80 and 69. I forwarded them to the 192.x.x.103 IP address of the PC which is running IIS. That PC runs Symantec Endpoint Protection, which I right mouse clicked in the tray to Disable. These steps used to make my PC visible so I could host my own web site in IIS on port 80, or some other port, like 69. Yet, the Open Port tool cannot see my IP when it checks eiether port and when I navigate to http://my external ip/ I get "page cant be displayed" At first I was thinking that maybe Comcast is blocking port 80, but 69 doesnt work eiether. I do not see any other blockking set up in my router and, as I mentioned, I went with teh defaults except where discussed. This is a corporate PC and Symantec End Point Protecion is new to it (this previously worked on teh same PC with Symantec Protection Agent), but I thought that disabling Sym End Pt from the tray, that that would effectively neutralize it. I do not have the rights to kill the program itself. Any suggestions on what else to try to make my PC externally visible?

  Read the article

• supervisord launches with wrong setuid

  - by friendzis

  I am trying to test a pilot system with nginx connecting to uwsgi served application controlled by supervisord running on ubuntu-server. Application is written in python with Flask in virtualenv, although I'm not sure if that is relevant. To test the system I have created a simple hello world with flask. I want nginx and uwsgi both to run as www-data user. If I launch uwsgi "manually" from root shell I can see uwsgi processes runing as appropriate user (www-data). Although, if I let supervisor launch the application something strange happens - uwsgi processes are runing under my user (friendzis). Consequently, socket file gets created under wrong user and nginx cannot communicate with my applicaion. note: the linux server runs as Hyper-V VM, under Windows Server 2008. Relevant configuration: [uwsgi] socket = /var/www/sockets/cowsay.sock chmod-socket = 666 abstract-socket = false master = true workers = 2 uid = www-data gid = www-data chdir = /var/www/cowsay/cowsay pp = /var/www/cowsay/cowsay pyhome = /var/www/cowsay module = cowsay callable = app supervisor [program:cowsay] command = /var/www/cowsay/bin/uwsgi -s /var/www/sockets/cowsay.sock -w cowsay:app directory = /var/www/cowsay/cowsay user = www-data autostart = true autorestart = true stdout_logfile = /var/www/cowsay/log/supervisor.log redirect_stderr = true stopsignal = QUIT I'm sure I'm missing some minor detail, but I'm unable to notice it. Would appreciate any suggestions.

  Read the article

• Emails going to Junk for Hotmail recipients

  - by David George

  We send daily mass emails to our customers (~30,000+ emails per day). We have problems with Hotmail users receiving our emails. Sometimes the email goes to the Junk folder, but often it will got to their inbox, but the content is blocked so the user sees a message saying "This email was blocked and may be dangerous". If an email is sent to GMAIL it is usually not blocked, but it does show up as from "Uknown" instead of the company. Please be advised I've done the following: 1. No RBLs Checked on - http://multirbl.valli.org/ 2. We do have SPF records published 3. We do have reverse DNS setup 4. Our company even signed up for the Junk Mail Reports Program at Hotmail Here is a sample header, I've noticed the X-SID-Result and the X-AUTH-Result both FAIL every time at Hotmail: X-Message-Delivery: Vj0xLjE7dXM9MDtsPTA7YT0wO0Q9MTtTQ0w9MQ== X-Message-Status: n:0 X-SID-Result: Fail X-AUTH-Result: FAIL X-Message-Info: JGTYoYF78jFqAaC29fBlDlD/ZI36+S6WoFmkQN10UxWFe1xLHhP+rDthGRZM87uHYM926hUBS+s0q46Yx9y6jdurhN6fx0bK Received: from privatecompany.com ([WanIPAddress]) by col0-mc3-f30.Col0.hotmail.com with Microsoft SMTPSVC(6.0.3790.4675); Wed, 5 May 2010 08:41:27 -0700 X-AuditID: ac10fe93-000013bc00000534-46-4be191a1618e Received: from INTERNAL-Email-SERVER([InternalIPAddress]) by privatecompany.com with Microsoft SMTPSVC(6.0.3790.4675); Wed, 5 May 2010 11:41:21 -0400 From: Private Company, Inc.<[email protected]> To: [email protected] Message-Id: <[email protected]> Subject: Date: Wed, 5 May 2010 11:42:46 -0400 MIME-Version: 1.0 Reply-To: [email protected] Content-Type: text/plain; charset="ISO-8859-1" Content-Transfer-Encoding: 8bit X-Brightmail-Tracker: AAAAAA== Return-Path: [email protected] X-OriginalArrivalTime: 05 May 2010 15:41:27.0837 (UTC) FILETIME=[6D06E4D0:01CAEC69]

  Read the article

• OS X 10.6 Apply ipfw rules at startup

  - by Michael Irey

  I have a couple of firewall rules I would to like to apply at startup. I have followed the instructions from http://images.apple.com/support/security/guides/docs/SnowLeopard_Security_Config_v10.6.pdf On page 192. However, the rules do not get applied at startup. I am running 10.6.8 NON Server Edition. I can however run: (Which applies the rules correctly) sudo ipfw /etc/ipfw.conf Which results in: 00100 fwd 127.0.0.1,8080 tcp from any to any dst-port 80 in 00200 fwd 127.0.0.1,8443 tcp from any to any dst-port 443 in 65535 allow ip from any to any Here is my /etc/ipfw.conf # To get real 80 and 443 while loading vagrant vbox add fwd localhost,8080 tcp from any to any 80 in add fwd localhost,8443 tcp from any to any 443 in Here is my /Library/LaunchDaemons/ipfw.plist <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple Computer//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Label</key> <string>ipfw</string> <key>Program</key> <string>/sbin/ipfw</string> <key>ProgramArguments</key> <array> <string>/sbin/ipfw</string> <string>/etc/ipfw.conf</string> </array> <key>RunAtLoad</key> <true /> </dict> </plist> The permissions of all the files seem to be appropriate: -rw-rw-r-- 1 root wheel 151 Oct 11 14:11 /etc/ipfw.conf -rw-rw-r-- 1 root wheel 438 Oct 11 14:09 /Library/LaunchDaemons/ipfw.plist Any thoughts or ideas on what could be wrong would be very helpful!

  Read the article

• How can i get more low memory with the following setup:

  - by user539484

  Modules using memory below 1 MB: Name Total = Conventional + Upper Memory -------- ---------------- ---------------- ---------------- MSDOS 14 317 (14K) 14 317 (14K) 0 (0K) HIMEM 1 120 (1K) 1 120 (1K) 0 (0K) EMM386 3 120 (3K) 3 120 (3K) 0 (0K) OAKCDROM 36 064 (35K) 36 064 (35K) 0 (0K) POWER 80 (0K) 80 (0K) 0 (0K) NLSFUNC 2 784 (3K) 2 784 (3K) 0 (0K) COMMAND 2 928 (3K) 2 928 (3K) 0 (0K) MSCDEX 15 712 (15K) 15 712 (15K) 0 (0K) SMARTDRV 30 384 (30K) 13 984 (14K) 16 400 (16K) KEYB 6 752 (7K) 6 752 (7K) 0 (0K) MOUSE 17 296 (17K) 17 296 (17K) 0 (0K) DISPLAY 8 336 (8K) 0 (0K) 8 336 (8K) SETVER 512 (1K) 0 (0K) 512 (1K) DOSKEY 4 144 (4K) 0 (0K) 4 144 (4K) POWER 4 672 (5K) 0 (0K) 4 672 (5K) Free 552 944 (540K) 539 088 (526K) 13 856 (14K) Memory Summary: Type of Memory Total = Used + Free ---------------- ---------- ---------- ---------- Conventional 653 312 114 224 539 088 Upper 47 920 34 064 13 856 Reserved 0 0 0 Extended (XMS)* 64 898 256 2 671 824 62 226 432 ---------------- ---------- ---------- ---------- Total memory 65 599 488 2 820 112 62 779 376 Total under 1 MB 701 232 148 288 552 944 Total Expanded (EMS) 33 947 648 (33 152K Free Expanded (EMS)* 33 538 048 (32 752K * EMM386 is using XMS memory to simulate EMS memory as needed. Free EMS memory may change as free XMS memory changes. Largest executable program size 538 976 (526K) Largest free upper memory block 7 488 (7K) MS-DOS is resident in the high memory area. I'm running MS-DOS 6.22 on VMWare virtual hardware. This is memory state after memmaker pass, so i'm looking for optimization beyond memmaker. Note: NLS drivers (DISPLAY, KEYB, NSLFUNC) are essential for me. Thanks to @mtone for valuable reminder about MSCDEX /E which gave me 16KiB of low memory (see the diff)!

  Read the article

• Help Installing SQL Server 2008 Express Edition

  - by Jordan S

  Ok I am running Windows 7, 64 bit. I cleaned of SQL server 2005 completely off my system leaving only SQL Compact Edition. I went here http://www.microsoft.com/downloads/details.aspx?FamilyID=01af61e6-2f63-4291-bcad-fd500f6027ff&displaylang=en and installed SQL Server 2008 Express Edition Service Pack 1. After the install, under my start bar menu all i have for SQL configuration tools are the Configuration Manager, Error and Usage Reporting and the Install Center. I don't have the SQL Managment Studio. So I went here http://www.microsoft.com/downloads/details.aspx?FamilyID=08e52ac2-1d62-45f6-9a4a-4b76a8564a2b&displaylang=en and downloaded the SQL Server 2008 Management Studio Express but when I try to install it I get a warning says This program has known compatibility issues and that I need to Install SQL Server 2008 Service Pack 1. I thought that is what I installed. So, I tried to continue running the install but I then get an error message that says Invoke or BeginInvoke can not be called on a Form before it is opened... How can I check if Service pack 1 is installed or not? What should I do? Also I rebooted my system and checked for Windows Updates and it says that Windows it up to date.

  Read the article

• "ImportError: No module named flask" - Trouble with nginx + uWSGI + Flask in a virtualenv setup

  - by vjk2005

  I got nginx + uWSGI running on localhost inside a virtualenv with a simple hello world program, but I get this error when I replace the hello world with a simple Flask app: File "./wsgi_configuration_module.py", line 1, in <module> from flask import Flask ImportError: No module named flask unable to load app mountpoint Here's the flask app (wsgi_configuration_module.py): from flask import Flask application = Flask(__name__) @application.route("/") def hello(): return "hello world" if __name__ == "__main__": application.run() uWSGI config (app_conf.xml): <uwsgi> <socket>127.0.0.1:9001</socket> <chdir>/srv/www/labs/application</chdir> <pythonpath>/srv/www</pythonpath> <module>wsgi_configuration_module</module> <callable>application</callable> <no-site>true</no-site> </uwsgi> nginx config: server { listen 80; server_name localhost; access_log /srv/www/labs/logs/access.log; error_log /srv/www/labs/logs/error.log; location / { include uwsgi_params; uwsgi_pass 127.0.0.1:9001; } location /static { root /srv/www/labs/public_html/static/; index index.html index.htm; } } virtualenv stored in ~/virtual_env with Python 2.7 + nginx + uWSGI + Flask installed in a virtualenv called basic. Things I've tried to solve this: set the --home (-H) option to my virtualenv folder ~/virtual_env while running uWSGI. Other info: I have the same setup working outside of a virtualenv. Things go wrong only when I try to replicate the setup inside of a virtualenv. Where have I gone wrong?

  Read the article

< Previous Page | 695 696 697 698 699 700 701 702 703 704 705 706  | Next Page >