Search Results

Search found 7595 results on 304 pages for 'dev dona'.

Page 7/304 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• /dev/sda2 contains a filesystem with error after partitioning

  - by Private

  I just wanted to create a separate home partition on my Ubuntu 12.10 system. I booted the liveDVD, resized the sda2 partition (28gb of data resized to 30gb based on MiB [originally on a 100gb partition]) and made a new ext4 partition for the home folder. The drive is an SSD drive. I had changed the settings (noatime etc.) for SSD succesfully a week ago. On reboot I get the following error: /dev/sda2 contains a filesystem with errors Inode 74669 has an invalid extent node (blk 6881289) fsd / [953] terminated with status 4 What would you suggest me to do? If I can avoid a clean install that would save me a lot of time (I had just done all the config). I was following this HOWTO, but I did not get to changing any of the files or configs other than those with gparted. I have a (two-week old) SSD Samsung drive which is functioning just fine (other specs see bottom of this question). Other specs: 64bit 12.10, i7, 8gb ram, nvidia.

  Read the article

• Failed to install GRUB on a separate '/boot' partition on a fake RAID 0 (12.04LTS)

  - by gerben

  I'm having some problems getting GRUB configured for Ubuntu 12.04LTS on a fake RAID 0. I can either get the GRUB rescue prompt at startup, or just a GRUB prompt but I cannot boot to Ubuntu manually. How can I configure the GRUB to actually use the Ubuntu install? The steps taken: Installing Ubuntu on fake raid The Ubuntu installer cannot install Ubuntu on the drive. After defining the partitions to use it fails with "Error: ???", pressing OK terminates the installer. Therefore, I used GParted to configure the partitions: /dev/mapper/sil_agadaccfacbg : (the RAID configuration, created partition): /dev/mapper/sil_agadaccfacbg1:ext2, 200MiB, (with 'boot' flag) /dev/mapper/sil_agadaccfacbg3:ext2, 67.75GiB, (which will contain Ubuntu) /dev/mapper/sil_agadaccfacbg2:extended, 1.00GiB, (for swap) Contains: /dev/mapper/sil_agadaccfacbg5: unknown Because of the fake-RAID, I already mounted the destination partitions before running the Ubuntu installer: > mkdir /mnt/boot > sudo mount /dev/mapper/sil_agadaccfacbg1 /mnt/boot > mkdir /mnt/ubuntu > sudo mount /dev/mapper/sil_agadaccfacbg3 /mnt/ubuntu In the installer I chose the following partition usage: /dev/mapper/sil_agadaccfacbg1 ext2, mount at /boot (209MB) /dev/mapper/sil_agadaccfacbg3 ext2, mount at / (72751MB) /dev/mapper/sil_agadaccfacbg5 swap Device for boot loader installation: /dev/mapper/sil_agadaccfacbg, linux device-mapper (striped) (74.0GB) This will install Ubuntu, but will fail to install GRUB (it seems to use /dev/sda no matter which one I choose) Installing GRUB with dpkg-reconfigure I followed this guide, but adapted it for two partitions: sudo mount /dev/mapper/sil_agadaccfacbg3 /mnt/ubuntu sudo mount --bind /dev /mnt/ubuntu/dev sudo mount --bind /proc /mnt/ubuntu/proc sudo mount --bind /sys /mnt/ubuntu/sys sudo mount /dev/mapper/sil_agadaccfacbg1 /mnt/boot sudo mount --bind /boot /mnt/boot sudo chroot /mnt/ubuntu dpkg-reconfigure grub-pc However, it does not ask where to install GRUB (I should choose /dev/mapper/sil_agadaccfacbg somewhere..) After reboot I get the GRUB rescue prompt with message no such device Installing GRUB with grub-install After the same mount commands as above, I continued with: > sudo grub-install --root-directory=/mnt/boot /dev/mapper/sil_agadaccfacbg This gives the following message: /usr/sbin/grub-probe: error: cannot find a device for /mnt/boot/boot/grub (is /dev mounted?) It does succeed when mounting just the boot partition : sudo mount /dev/mapper/sil_agadaccfacbg1 /mnt sudo grub-install --root-directory=/mnt/ /dev/mapper/sil_agadaccfacbg This finishes with: Installation finished. No error reported. After reboot I get the GRUB console, with welcome text. Attempting to manually start Ubuntu: ls (hd0) (hd0,msdos3) : (Ubuntu install partition) (hd0,msdos1) : (Ubuntu boot partition) (hd1) (hd1,msdos1) : (Ubuntu live USB) ls (hd0,msdos3)/ contains: - vmlinuz - lib/ - tmp/ - initrd.img - mnt/ - var/ - proc/ - boot/ - root/ - etc/ - run/ - media/ - sbin/ - bin/ - selinux/ - dev/ - srv/ - home/ - sys/ ls (hd0,msdos1)/ contains: -grub/ -boot/ -initrd.img-3.8.0-29-generic -vmlinuz-3.8.0.29-generic -config-3.8 linux (hd0,msdos3)/vmlinuz This returns "error: out of disk" Installing GRUB on Ubuntu partition with grub-install > sudo mount /dev/mapper/sil_agadaccfacbg3 /mnt > sudo grub-install --root-directory=/mnt/ /dev/mapper/sil_agadaccfacbg This finishes with message: > Installation finished. No error reported. After reboot get the message "error: out of disk" and the GRUB rescue prompt. Configuring GRUB with grub-mkconfig Attempting to run grub-mkconfig with different destinations results in the same message: /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?). Remarks: Initially I didn't use a separate /boot partition, but the GRUB install then also failed. Because some mention that a small partition at the beginning of the drive is necessary on old machines, I retried with a /boot partition This is a single boot (no other OS's installed/used)

  Read the article

• Raid1+0: create stripe over two /dev/mdx on partition or not?

  - by Chris

  Given that I haven't found a way to define how a Raid10 is created with mdadm, i went the Raid1+0 solution. How to display/define Mirror/Stripping pairs with mdadm mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sda1 /dev/sdf1 mdadm --create /dev/md1 --level=1 --raid-devices=2 /dev/sdg1 /dev/sdh1 mdadm --create /dev/md10 --level=0 --raid-devices=2 /dev/md0 /dev/md1 My question is about the stripe. For the mirror I create a primary partition over the full HD and set partition type to FD. So, should I do the same for the Stripe? Create partition on /dev/md0 and /dev/md1 (primary over full 'HDD', set partition type correctly) and then do the stripe on the partition? Is there a correct way here or are there any advantages/disadvantages to a solution? Thank you

  Read the article

• Connecting to MSP430 via /dev/ttyACM0

  - by speciousfool

  I'd like some suggestions about how to fix garbled serial output from a device connected on /dev/ttyACM0. Lately I've been working on a development project making use of TI's MSP430 microcontroller (specifically the eZ430-RF2560). Over on this thread you can see we've been testing some code and have found that the output of the microcontroller over serial is garbled. The btstack provides simple counter test program. When we run the program and look at the serial port output using PuTTY on Windows 7 we see: rfcomm_send_internal cid 117 doesn't exist! BTstack counter 26230 rfcomm_send_internal cid 117 doesn't exist! BTstack counter 26231 However if we connect from various Ubuntu clients we get something like: Stt.R. BTacn 0 BTacn 002BTacn 0 BTcct 04BTtacoe 5BTacun My current belief is that this is because the device is being detected by cdc_acm as a generic USB ACM device. Another thread about a similar microcontroller suggests that the device should use a specific usb serial driver. We've verified that the module is compiled on our system and did a "modprobe ti_usb_3410_5052" but this had no effect on cdc_acm. Here is the relevant section of the kernel's debug log: [ 2735.092987] usb 2-1.2: new full speed USB device number 5 using ehci_hcd [ 2735.213655] cdc_acm 2-1.2:1.0: This device cannot do calls on its own. It is not a modem. [ 2735.213669] cdc_acm 2-1.2:1.0: No union descriptor, testing for castrated device [ 2735.213720] cdc_acm 2-1.2:1.0: ttyACM0: USB ACM device [ 2745.241996] generic-usb 0003:0451:F432.0003: usb_submit_urb(ctrl) failed [ 2745.242023] generic-usb 0003:0451:F432.0003: timeout initializing reports [ 2745.242401] generic-usb 0003:0451:F432.0003: hiddev0,hidraw0: USB HID v1.01 Device [Texas Instruments Texas Instruments MSP-FET430UIF] on usb-0000:00:1d.0-1.2/input1 So, in summary, we'd like to figure out how to properly connect to this device. Also of use may be the appropriate place to file a bug report.

  Read the article

• West Palm Beach Dev Group August 2012 Meeting Recap

  - by Sam Abraham

  As the saying goes, it’s better late than never. Such is the case with my overdue West Palm Beach Dev Group August 2012 meeting report. Our August meeting was full of both knowledge and adventure. It comes as no surprise that the knowledge was brought to us by our favorite DotNetNuke Technical Evangelist, Will Strohl. Will introduced and thoroughly presented the new social features in DNN 6.2. Unfortunately, our meeting date coincided with Hurricane Isaac having just passed us by. Aside from road closures and floods that kept public schools closed for two days, our meeting host, PC Professor, had to close the school the day of our meeting on a short notice due to flooding which we found out about at midnight on the day of the event.  This left us scrambling to find an available alternate meeting location close enough to our original venue. Cancelling the meeting was always an option, but we opted to keep it as the very last resort. Luckily, we were fortunate to find a meeting room at the Hampton Inn only a few minutes away from our original location. Having heard of our challenge, our event sponsor, Applied Innovations, stepped-in and covered the meeting room cost in addition to the food and beverages. We would like to thank our volunteers and sponsors who made that event a success: Jess Coburn, CEO and Cara Pluff, Director of Sales at Applied Innovations, Dave Noderer for suggesting the alternate venue and Venkat Subramanian for his hard work keeping our members informed of the venue change and for being our event photographer.   We look forward to seeing you at our upcoming meetings: -September 25th, 2012 with Jonas Stawski, Microsoft MVP -October 23rd, 2012 with our Microsoft Developer Evangelist, Joe “DevFish” Healy -Ending an exciting year will be our November 27th meeting with Dycom Industries’ Senior Software Developer, Tom Huynh.   All the best, --Sam

  Read the article

• wxCam can't open /dev/dsp

  - by SIJAR

  I try to run wxCam through PulseAudio using the following command: $ padsp -d wxcam Although wxCam started ok, wxCam is been set to use xdiv format to enable sound during recording, but while recording the I get the error: Cannot open /dev/dsp. Video file will be recorded without audio track Please help me in fixing this issue. Below is some debug information: $ padsp -d wxcam Determining video4linux API version... Using video4linux 2 API VIDIOC_ENUM_FRAMESIZES: Invalid argument V4L2_CID_GAMMA is not supported Determining pixel format... pixel format: YUV 4:2:2 (YUYV) Found V4L2_PIX_FMT_YUYV pixel format pixel format: MJPEG Found V4L2_PIX_FMT_MJPEG pixel format --DEBUG: [wxcam] Generating standard Huffman tables for this frame. Corrupt JPEG data: 2 extraneous bytes before marker 0xd2 ... repeats a couple of times ... open of failed: No such file or directory --DEBUG: [wxcam] Generating standard Huffman tables for this frame. Corrupt JPEG data: 2 extraneous bytes before marker 0xd4 ... repeats a couple of times .... /home/sij/Videos/Webcam/video.avi written: 640x480, 1334396 bytes --DEBUG: [wxcam] Generating standard Huffman tables for this frame. Corrupt JPEG data: 2 extraneous bytes before marker 0xd3 ... repeats a couple of times ...

  Read the article

• Microsoft Dev Days &ndash; Johannesburg 2010

  - by MarkPearl

  So I am half way through dev days in Johannesburg. It has been quite an interesting day… Maybe it is me, but this year it hasn’t been as OMG as at previous conferences. A few things that stood out though… 1) This is the first time I have had to queue in a line to use the gents toilets before – yes, a true sign that we are at a typically male dominated industry event in this country – the men’s toilets were jam packed – the ladies if there were any there didn’t have a problem. 2) Bart De Smet presentation still rocks – I am a fan of Bart’s and once again his presentation was great. Something that I am going to look into in more depth which I think is a new feature in .Net is called Code Contracts. 3) I have got to get into Silverlight more… I have known this for a long time and have dabbled in it for a while, but Silverlight in my opinion will become the main platform for “hosting” applications. So… 3 things so far, hopefully I get some OMG’s from the rest of the day…

  Read the article

• Cannot Connect Modem ( /dev/ttySL0 ) Using gnome-ppp - Dial-Up Connection

  - by nicorellius

  I'm trying to connect my Toshiba Satellite running Ubuntu 10.04 to my Eris running Android 2.1 through a Bluetooth connection and establish a dial-up connection (DUN) with the modem. I can connect my phone to my laptop, and I can detect my modem (after installing drivers), which is located at /dev/ttySL0. But when I launch gnome-ppp and enter my phone number (123 for PDA-Net) I get a dialog that says "Connecting... Sending Password" with Log and Cancel buttons. The log shows this: --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Please enter password (or empty password to stop): --> Configuration does not specify a valid login name. The PDA-Net DUN protocol is running and shows no error. Any ideas? Any help is much appreciated.

  Read the article

• raid md device is not remove from memory, how to overcome this problem

  - by santhosha

  i create raid 10 , i removed two arrays form md11 one by one , after that i going to editing the contents those are mounted ( it will be not responding stage), after i try for remove arrays those are left it is shows device or resource busy ( is not removed from memory). i try to terminate process this is also not work, i absorve from 4 days resync will be 8.0% it can not modifying. cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec mdadm -D /dev/md11 /dev/md11: Version : 00.90.03 Creation Time : Sun Jan 16 16:20:01 2011 Raid Level : raid10 Array Size : 286743936 (273.46 GiB 293.63 GB) Device Size : 143371968 (136.73 GiB 146.81 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 11 Persistence : Superblock is persistent Update Time : Sun Jan 16 16:56:07 2011 State : active, degraded, resyncing Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K Rebuild Status : 8% complete UUID : 5e124ea4:79a01181:dc4110d3:a48576ea Events : 0.23 Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 4 8 145 2 faulty spare rebuilding /dev/sdj1 3 8 65 3 active sync /dev/sde1 umount /dev/md11 umount: /dev/md11: not mounted mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 kill -9 2128 kill -9 5018 kill -9 27605 kill -9 30562 kill -3 30591 mdadm -S /dev/md11 mdadm: fail to stop array /dev/md11: Device or resource busy lsof /dev/md11 COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME mount 2128 root 3r BLK 9,11 4058 /dev/md11 mount 5018 root 3r BLK 9,11 4058 /dev/md11 mdadm 27605 root 3r BLK 9,11 4058 /dev/md11 mount 30562 root 3r BLK 9,11 4058 /dev/md11 badblocks 30591 root 3r BLK 9,11 4058 /dev/md11 cat /proc/mdstat Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [linear] [raid10] md11 : active raid10 sde1[3] sdj14 286743936 blocks 64K chunks 2 near-copies [4/1] [___U] [1:2:3:0] [=...................] resync = 8.0% (23210368/286743936) finish=289392.6min speed=15K/sec

  Read the article

• Blocking a distributed, consistent spam attack? Could it be something more serious?

  - by mattmcmanus

  I will do my best to try and explain this as it's strange and confusing to me. I posted a little while ago about a sustained spike in mysql queries on a VPS I had recently setup. It turned out to be a single post on a site I was developmenting. The post had over 30,000 spam comments! Since the site was one I was slowly building I hadn't configured the anti-spam comment software yet. I've since deleted the particular post which has given the server a break but the post's url keeps on getting hit. The frustrating thing is every hit is from a different IP. How do I even start to block/prevent this? Is this even something I need to worry about? Here are some more specific details about my setup, just to give some context: Ubuntu 8.10 server with ufw setup The site I'm building is in Drupal which now has Mollom setup for spam control. It wasn't configured before. The requests happen inconsistently. Sometimes it's every couple seconds and other times it's a an or so between hits. However it's been going on pretty much constantly like that for over a week. Here is a sample of my apache access log from the last 15 minutes just for the page in question: dev.domain-name.com:80 97.87.97.169 - - [28/Mar/2010:06:47:40 +0000] "POST http://dev.domain-name.com/comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 202.149.24.193 - - [28/Mar/2010:06:50:37 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 193.106.92.77 - - [28/Mar/2010:06:50:39 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 194.85.136.187 - - [28/Mar/2010:06:52:03 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 220.255.7.13 - - [28/Mar/2010:06:52:14 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 195.70.55.151 - - [28/Mar/2010:06:53:41 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 71.91.4.31 - - [28/Mar/2010:06:56:07 +0000] "POST http://dev.domain-name.com/comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 98.209.203.170 - - [28/Mar/2010:06:56:10 +0000] "POST http://dev.domain-name.com/comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 24.255.137.159 - - [28/Mar/2010:06:56:19 +0000] "POST http://dev.domain-name.com/comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 77.242.20.18 - - [28/Mar/2010:07:00:15 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 94.75.215.42 - - [28/Mar/2010:07:01:34 +0000] "POST /comment/reply/3 HTTP/1.0" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 89.115.2.128 - - [28/Mar/2010:07:03:20 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 75.65.230.252 - - [28/Mar/2010:07:05:05 +0000] "POST http://dev.domain-name.com/comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 206.251.255.61 - - [28/Mar/2010:07:06:46 +0000] "POST /comment/reply/3 HTTP/1.0" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" dev.domain-name.com:80 213.194.120.14 - - [28/Mar/2010:07:07:22 +0000] "POST /comment/reply/3 HTTP/1.1" 404 5895 "http://dev.domain-name.com/blog/2009/11/23/another" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)" I understand this is an open ended question, but any help or insight you could give would be much appreciated.

  Read the article

• Dell XPS 15 (L502x) sound problem

  - by lauramolenaar

  I have a problem with my sound on my Dell XPS 15. First, when I had Windows 7, my sound was pretty good (I have a JBL 2.1 speaker system with Waves Maxx audio), but since I installed Ubuntu 12.04 it sounded very cheap and as if I put my laptop in a tin can. I've already tried installing alsa-hda-dkms from the alsa-daily ppa (http://ppa.launchpad.net/ubuntu-audio-dev/alsa-daily) This is my audio controller: laura@laura-XPS-L502X:~$ lspci -v | grep -A7 -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04b6 Flags: bus master, fast devsel, latency 0, IRQ 51 Memory at f1c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel I hope you can help me, and you can always ask me for more information. Result of aplay -l: **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 0/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 Result of aplay -L: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC665 Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Digital IEC958 (S/PDIF) Digital Audio Output hdmi:CARD=PCH,DEV=0 HDA Intel PCH, HDMI 0 HDMI Audio Output dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample mixing device dmix:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample mixing device dmix:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct sample snooping device dsnoop:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct sample snooping device dsnoop:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Direct hardware device without any conversions hw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Direct hardware device without any conversions hw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC665 Analog Hardware device with all software conversions plughw:CARD=PCH,DEV=1 HDA Intel PCH, ALC665 Digital Hardware device with all software conversions plughw:CARD=PCH,DEV=3 HDA Intel PCH, HDMI 0 Hardware device with all software conversions

  Read the article

• /dev/input/uinput Device appears to be 'broken'

  - by Adam Luchjenbroers

  I'm trying to setup Pystromo so that I can remap the keys on my Belkin N52TE gamepad. Pystromo basically captures the key strokes and then outputs the remapped keystrokes to the uinput device. However, at the moment it simply swallows the input and outputs absolutely nothing. I've tracked the issue to something being wrong with my uinput device, with the smoking gun being: # ls -l /dev/input/uinput crw-rw---- 1 root plugdev 10, 223 Dec 31 2009 /dev/input/uinput # cat /dev/input/uinput cat: /dev/input/uinput: No such device The uinput module is loaded, and can be clearly seen via lsmod. Anyone seen this before, or can think of something worth attempting? Current Setup Gentoo Linux Kernel 2.6.32 (Gentoo Sources 2.6.32-r1) HP DV7 Laptop Output dmesg dmesg | grep uinput does nothing, and no new lines appear if I run modprobe -r uinput && modprobe uinput. Yet the uinput module can clearly be seen when running lsmod: # lsmod | grep uinput uinput 6200 0 lsusb # lsusb Bus 005 Device 003: ID 050d:0200 Belkin Components Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 1532:0101 Razer USA, Ltd Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 5986:0143 Acer, Inc Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 002: ID 03f0:171d Hewlett-Packard Wireless (Bluetooth + WLAN) Interface [Integrated Module] Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsusb -v PasteBin Update Hmm, updating evdev and hal seems to have partially fixed it. /dev/input/uinput still can't be accessed but Pystromo is now remapping keys successfully. I'm a little bit mystified about what's going on here, but it seems that my understanding of how all this works is flawed. Since I've posted a bounty, I'll leave this here for someone to post an explanation for how user-space input devices work under the hood.

  Read the article

• /dev/fuse "permission denied" even when member of fuse group

  - by steeef

  I have a backup script scheduled on a Debian 5.0 x86 server, via sshfs. However, when I attempt to mount the remote directory, I receive: failed to open /dev/fuse: Permission denied ls -l /dev/fuse returns: crwxrwxr-x 1 root fuse 10, 229 2010-11-12 09:08 /dev/fuse id backup returns: uid=501(backup) gid=501(backup) groups=501(backup),46(plugdev),108(fuse) The only way I can get the directory to mount is if I run chmod a+w /dev/fuse, but this is reset at some point during the day. It's a kludge though, and I'd rather figure out why the group permissions aren't working.

  Read the article

• DegradedArray event on /dev/md0 without actually having a RAID

  - by J. Stoever

  Since I upgraded from Ubuntu LTS 10 to LTS 12, I have been getting error messages like: N 60 mdadm monitoring Mon Sep 3 06:38 31/1022 DegradedArray event on /dev/md2:Ubuntu-1004-lucid-64-minimal N 61 mdadm monitoring Mon Sep 3 06:38 31/1022 DegradedArray event on /dev/md0:Ubuntu-1004-lucid-64-minimal N 62 mdadm monitoring Mon Sep 3 06:38 31/1022 DegradedArray event on /dev/md1:Ubuntu-1004-lucid-64-minimal We do not have a RAID setup, and only have a single hard drive. Ideas ?

  Read the article

• /dev/shm (shared memory) on linux

  - by Kirzilla

  Hello, Let's imagine that we have 8Gb of RAM on server. I'm mounting /dev/shm with 4Gb on board. mount -o remount,size=4G /dev/shm Will this memory be strictly reserved for shared memory or if /dev/shm is empty this memory could be used by regular applications (web server, php etc.)? PS:Sorry for my English. I'm asking it because I've just checked df -h and found tmpfs 6.0G 0 6.0G 0% /dev/shm on 8Gb RAM sever. I don't know who made this setup, but it seems to me awful. Thank you!

  Read the article

• Is there an alternative to /dev/urandom?

  - by altCognito

  Is there some faster way than /dev/[u]random? Sometimes, I need to do things like cat /dev/urandom /dev/sdb The random devices are "too" secure und unfortunately too slow for that. I know that there are wipe and similar tools for secure deletion, but I suppose there are also some on-board means to that in Linux.

  Read the article

• Timestamp Updating Constantly on /dev/null

  - by motorleague

  I've been working on a problem with a /dev/null file on an AIX system (just for background it looks as though it was inadvertently deleted and recreated as a normal file by somebody), but in trying to determine what caused the problem, I noticed that the timestamp on it seems to update every minute. I've observed this on several AIX servers at my workplace. At present I can't entirely rule out this be something specific to the Application being used at my workplace, so I compared with CentOS and Debian based computers at home last night. The CentOS box, which runs 24 hours, had a mod time on /dev/null of around 4 days ago (during which time it was essentially just being used as a web browser and multimedia player, although it would have had active but essentially unused Apache, MySQL and VMM processes running in the background). The timestamp on /dev/null on the Debian machine, which was a just booted laptop, pretty much reflected the boot time, but I tested redirecting STDIN from, and STDOUT to it, and the modification time was unchanged (I'm not sure 100% sure if directing data to /dev/null constitutes "writing to it" in the way it would a normal file). So my question is essentially, could anybody please offer any advice with regards to what circumstances (permissions changes etc.. aside) might cause the timestamp on /dev/null to update? Thanks very much for any suggestions. Alex.

  Read the article

• How to set up multi users on dev server with git and github

  - by Derek Organ

  I'm working on lamp application. We have 2 servers (Debian) Live and Dev. I constantly work on dev main to add new features and fix bugs. When happy all works well I scp the relevant code to the Live system. Database (mysql) is local to each machine. Now this is pretty basic setup really and I want to improve the workflow a bit. I use git and github for version control. Admittedly I've only really used one branch. Their can be 3 different developers who work on the code at different times. We all use the same linux username to connect to the dev server and edit the code directly when needed. I usually then commit and push the code at the end of the day to github. One thing to bare in mind is it isn't easy to run this code on a local machine as there are many apache and subdomain configurations that wouldn't work on a local machine so it is important to work on the dev server not locally. I need to create a new process because we need to have a main trunk now and a branch with a big code re-write. What is the best way to do this. Should I create different unix logins for each developer and set up different working areas on the dev server for there changes? e.g. /var/www/mysite_derek /var/www/mysite_paul /var/www/mysite_mike my thinking is they can do a pull from the main branch and then create there own branch and merge it back in. I'm not sure how this will work though with git locally and with github. will i need to create different github user accounts as well. I'd like to do this the 'right' way and future proof for having lots of potential developers but I also don't want to over complicate it. I simple and elegant solution is preferred. any recommendations or suggestions?

  Read the article

• Can I get a faster output pipe than /dev/null ?

  - by naugtur

  Hi I am running a huge task [automated translation scripted with perl + database etc.] to run for about 2 weeks non-stop. While thinking how to speed it up I saw that the translator outputs everything (all translated sentences, all info on the way) to STDOUT all the time. This makes it work visibly slower when I get the output on the console. I obviously piped the output to /dev/null, but then I thought "could there be something even faster?" It's so much output that it'd really make a difference. And that's the question I'm asking You, because as far as I know there is nothing faster... (But I'm far from being a guru having used linux on a daily basis only last 3 years)

  Read the article

• Swap not available on System Monitor

  - by Zaki

  I had a swap partition of 1GB (RAM 1GB, Ubuntu 12.04 lts). Now swap is not shown on System Monitor neither can I hibernate my pc (sudo pm-hibernate). blkid output: /dev/sda1: UUID="B8B4FBB1B4FB706C" TYPE="ntfs" /dev/sda2: UUID="2ea7d608-2d89-4e41-9436-d05cb3ce8871" TYPE="swap" /dev/sda3: UUID="3219d03a-67e4-454b-8ce7-a27831846e35" TYPE="ext4" /dev/sda5: LABEL="Softwares" UUID="AC1CC3301CC2F47C" TYPE="ntfs" /dev/sda6: LABEL="Education" UUID="1E103E6C103E4B53" TYPE="ntfs" /dev/sda7: LABEL="Recreation" UUID="2CC8D181C8D149AA" TYPE="ntfs" /dev/sda8: LABEL="Miscellaneous" UUID="0274D6B174D6A727" TYPE="ntfs" /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda6 during installation UUID=3219d03a-67e4-454b-8ce7-a27831846e35 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=2ea7d608-2d89-4e41-9436-d05cb3ce8871 none swap sw 0 0 free -m total used free shared buffers cached Mem: 991 867 123 0 27 418 -/+ buffers/cache: 421 569 Swap: 0 0 0 cat /proc/swaps Filename Type Size Used Priority fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9f369f36 Device Boot Start End Blocks Id System /dev/sda1 * 63 31471334 15735636 7 HPFS/NTFS/exFAT /dev/sda2 31471616 33470447 999416 82 Linux swap / Solaris /dev/sda3 33472512 62539775 14533632 83 Linux /dev/sda4 62541045 312592769 125025862+ f W95 Ext'd (LBA) /dev/sda5 62541108 125066024 31262458+ 7 HPFS/NTFS/exFAT /dev/sda6 125066088 187591004 31262458+ 7 HPFS/NTFS/exFAT /dev/sda7 187591068 250115984 31262458+ 7 HPFS/NTFS/exFAT /dev/sda8 250116048 312576704 31230328+ 7 HPFS/NTFS/exFAT swapon --all swapon: /dev/sda2: swapon failed: Invalid argument dmesg | grep -A 5 -B 5 -i swap [ 9.487404] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131645 [ 9.487413] EXT4-fs (sda3): ext4_orphan_cleanup: deleting unreferenced inode 131330 [ 9.487418] EXT4-fs (sda3): 16 orphan inodes deleted [ 9.487420] EXT4-fs (sda3): recovery complete [ 9.578600] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null) [ 20.580539] Swap area shorter than signature indicates [ 20.588363] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 20.619443] udevd[330]: starting version 175 [ 20.649959] lp: driver loaded but no devices found [ 20.662972] [drm] Initialized drm 1.1.0 20060810 [ 20.675515] i915 0000:00:02.0: setting latency timer to 64 -- [ 72.288573] PM: thaw of drv:sr dev:3:0:0:0 complete after 178.143 msecs [ 72.288578] PM: thaw of drv:scsi_device dev:3:0:0:0 complete after 178.136 msecs [ 72.299677] PM: thaw of drv:scsi_device dev:2:0:0:0 complete after 189.270 msecs [ 72.309473] PM: thaw of devices complete after 202.763 msecs [ 72.309668] PM: writing image. [ 72.309670] PM: Cannot find swap device, try swapon -a. [ 72.309699] PM: Cannot get swap writer [ 72.329896] Restarting tasks ... done. [ 72.331777] PM: Basic memory bitmaps freed [ 72.331792] video LNXVIDEO:00: Restoring backlight state [ 72.420048] option1 ttyUSB0: option_instat_callback: error -84 [ 72.804047] option1 ttyUSB0: option_instat_callback: error -84 -- [ 145.960625] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 145.972036] sd 7:0:0:0: [sdb] Attached SCSI removable disk [ 172.430508] PPP BSD Compression module registered [ 172.455583] PPP Deflate Compression module registered [ 332.260789] type=1400 audit(1381814763.342:27): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 1913.030998] Swap area shorter than signature indicates [ 2022.530155] type=1400 audit(1381816453.610:28): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=636 comm="cupsd" pid=636 comm="cupsd" capability=36 capname="block_suspend" [ 4062.729509] Swap area shorter than signature indicates Please help. Thanks in advance. df -h Filesystem Size Used Avail Use% Mounted on /dev/sda3 14G 6.1G 7.0G 47% / udev 488M 4.0K 488M 1% /dev tmpfs 199M 868K 198M 1% /run none 5.0M 4.0K 5.0M 1% /run/lock none 496M 224K 496M 1% /run/shm

  Read the article

• linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

  - by devicerandom

  We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

  Read the article

• How to solve package issues/dependencies

  - by Wolfgang Kuehne

  Background info I am trying to install Veins simulation environment by following the tutorial provided by the author. In step 1 it is required to install some packages in Linux, the tutorial suggest this commands to be executed on Terminal: sudo apt-get install build-essential gcc g++ bison flex perl tcl-dev tk-dev blt libxml2-dev zlib1g-dev default-jre doxygen graphviz libwebkitgtk-1.0-0 openmpi-bin libopenmpi-dev libpcap-dev autoconf automake libtool libxerces-c2-dev proj libgdal1-dev libfox-1.6-dev When I execute this command, I immediately get: E: Package 'proj' has no installation candidate Then I remove the proj from the command and execute it again without proj in it, next I get: The following packages have unmet dependencies: libgdal1-dev : Depends: libgdal-dev but it is not going to be installed E: Unable to correct problems, you have held broken packages. So, I remove libgdal1-dev from the command as well. And it executes file, by downloading the remaining packages. To troubleshoot the problem with proj and libdgal1-dev I go to the Synaptic Package Manager. libgdal1-dev I search for libgdal1-dev in Synaptic Package Manager and I get an entry. I Mark for Installation and then Synaptic Package Manager suggests removing libxerces-c2-dev which is actually added via the initial command. Should I trust Synaptic Package Manager with this suggestion, and proceed further? proj What should I do about proj. There are some packages in Synaptic Package Manager such as proj-bin or libproj-dev. Should I install them? I think proj has to do with this and this What should I do to make sure that this simulation tool works fine?

  Read the article

• Cloned partition not seen correctly by disk utility & gparted

  - by enrico

  Some days ago I cloned my /dev/sda1 partition with clonezilla in partition-to-partition mode to /dev/sda3. It worked, but now that I've finished the setup of system in /dev/sda3, I wanna reinstall /dev/sda1 for other stuffs. This partition is NOT mounted, but ubuntu's DISK UTILITY thinks it is, while it doesn't see as mounted the currently active / partition /dev/sda3. This is the df- TH output : Filesystem Type Size Used Avail Use% Mounted on /dev/sda3 ext4 32G 6.2G 24G 21% / udev devtmpfs 2.2G 13k 2.2G 1% /dev tmpfs tmpfs 845M 906k 844M 1% /run none tmpfs 5.3M 0 5.3M 0% /run/lock none tmpfs 2.2G 115k 2.2G 1% /run/shm /dev/sdb1 fuseblk 321G 147G 174G 46% /Dati Gparted instead, sees /dev/sda1 as NOT mounted (checked with Information option), but it display the BOOT flag on this partition, while the real booted partition /dev/sda3, hasn't it. If I try to format the /dev/sda1 partition, it gives me this error : GParted 0.8.1 --enable-libparted-dmraid Libparted 2.3 Format /dev/sda1 as ext2 00:00:02 ( ERROR ) calibrate /dev/sda1 00:00:00 ( SUCCESS ) path: /dev/sda1 start: 2048 end: 62500863 size: 62498816 (29.80 GiB) set partition type on /dev/sda1 00:00:02 ( SUCCESS ) new partition type: ext2 create new ext2 file system 00:00:00 ( ERROR ) mkfs.ext2 -L "" /dev/sda1 mke2fs 1.41.14 (22-Dec-2010) /dev/sda1 is mounted; will not make a filesystem here! How is possible to correct this behaviour ? Is this due to some lacking option in clonezilla phase ? TIA Enrico

  Read the article

• How do I mount my External HDD with filesystem type errors?

  - by Snuggie

  I am a relatively new Ubuntu user and I am having some difficulty mounting my external 2TB HDD. When I first installed Linux my external HDD was working just fine, however, it has stopped working and I have a lot of important files on there that I need. Before my HDD would automatically mount and no worries. Now, however, it doesn't automatically mount and when I try to manually mount it I keep running into filesystem type errors that I can't seem to get past. Below are images that depict my step by step process of how I am trying to mount my HDD along with the errors I am receiving. If anybody has any idea what I am doing wrong or how to correct the issue I would greatly appreciate it. Step 1) Ensure the computer recognizes my external HDD. pj@PJ:~$ dmesg ... [ 5790.367910] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1022 PQ: 0 ANSI: 6 [ 5790.368278] scsi 7:0:0:1: Enclosure WD SES Device 1022 PQ: 0 ANSI: 6 [ 5790.370122] sd 7:0:0:0: Attached scsi generic sg2 type 0 [ 5790.370310] ses 7:0:0:1: Attached Enclosure device [ 5790.370462] ses 7:0:0:1: Attached scsi generic sg3 type 13 [ 5792.971601] sd 7:0:0:0: [sdb] 3906963456 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 5792.972148] sd 7:0:0:0: [sdb] Write Protect is off [ 5792.972162] sd 7:0:0:0: [sdb] Mode Sense: 47 00 10 08 [ 5792.972591] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.972605] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.975235] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.975249] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.987504] sdb: sdb1 [ 5792.988900] sd 7:0:0:0: [sdb] No Caching mode page found [ 5792.988911] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 5792.988920] sd 7:0:0:0: [sdb] Attached SCSI disk Step 2) Check if it mounted properly (it does not) pj@PJ:~$ df -ah Filesystem Size Used Avail Use% Mounted on /dev/sda1 682G 3.9G 644G 1% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 2.9G 4.0K 2.9G 1% /dev devpts 0 0 0 - /dev/pts tmpfs 1.2G 928K 1.2G 1% /run none 5.0M 0 5.0M 0% /run/lock none 2.9G 156K 2.9G 1% /run/shm gvfs-fuse-daemon 0 0 0 - /home/pj/.gvfs Step 3) Try mounting manually using NTFS and VFAT (both as SDB and SDB1) pj@PJ:~$ sudo mount /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t ntfs /dev/sdb /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb': Invalid argument The device '/dev/sdb' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so pj@PJ:~$ sudo mount -t ntfs /dev/sdb1 /media/Passport/ NTFS signature is missing. Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? pj@PJ:~$ sudo mount -t vfat /dev/sdb1 /media/Passport/ mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

  Read the article

• I’m a dev is this relevant to me?

  - by simonsabin

  I was asked the question today whether the master class that Paul and Kimberley are running next month  (http://www.regonline.co.uk/builder/site/tab1.aspx?EventID=860887 ) is relevant for someone that is a developer. Yes yes yes yes . Consider it like your favourite album, there might be some of the songs that you hate but the rest you love and a couple in particular you will listen to all the time. If you are a developer then you will find that some of the stuff around backs and recovery might...(read more)

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >