Search Results

Search found 242 results on 10 pages for 'disconnects'.

Page 7/10 | < Previous Page | 3 4 5 6 7 8 9 10  | Next Page >

• How to fix unstable RJ45 jacks? [closed]

  - by BeemerGuy

  This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

  Read the article

• Android tethering via bluetooth keeps disconnecting

  - by Ian

  I'm currently using a Google Nexus tablet tethered via Bluetooth to a Samsung S3 for internet. Two things are annoying me. First, if I take the phone away from the tablet (go out for lunch), the tablet disconnects and has to be manually reconnected. Is there a way to have that happen automatically? Second, Bluetooth tethering, i.e. the internet sharing part needs to be switched on each time the bluetooth is switched on (or perhaps just after power cycling) on the S3. Is there no way to have that default to on? Thanks

  Read the article

• When can an FTP server close its passive connections?

  - by Don Kirkby

  Does the FTP protocol allow the server to close any of its passive connections while the client is still connected? Can it tell when the client is finished receiving and then close the connection? I'm including an FTP server in my application using the pyftpdlib Python project. I've got it to work in active and passive mode, but I'm a bit concerned about when it closes its passive connections. I've tried connecting to it with both FileZilla and the default ftp command in Ubuntu, and in both cases, I get a new passive port for every request. That is, if I sit in the root folder and type ls 10 times, I use up 10 ports. This means that I have to allocate a big block of passive ports for the FTP server to use so it won't run out. As soon as the client disconnects, the server releases all the passive connections associated with that client and those ports can be reused. However, a long-running connection could use up a lot of ports.

  Read the article

• Failing SSHFS connection drags down the system

  - by skerit

  From time to time my sshfs mount fails. All programs using the mount freeze when it happens. I can't even ls anything or use nautilus. Is there a way to find out what's the cause and how to handle it? I've noticed regular SSH sessions to the server get their fair share of Write failed: broken pipe disconnects, too. If I wait long enough (and I'm talking about 20-ish minutes, here) it will auto reconnect and things start working again.

  Read the article

• Why does the Internet WI-FI connection of my laptop disconnect when I connect the ethernet cable to the LAN?

  - by Joey Hammer

  Why does the Internet WI-FI connection of my laptop disconnect when I connect the ethernet cable to the LAN? These are two separate networks, the LAN is without Internet, I just use it to connect the tablet to the laptop and smart phone in my home network. The WI-FI is owned by the landlady and connects to the Internet. I know it should be possible to be connected both to the Internet through WI-FI and to my other computers and gadgets through the LAN because sometimes it works, but sometimes when I connect the ethernet cable the WI-FI disconnects and I wonder why? Pongy OS: Windows 7

  Read the article

• How to manage large number of desktop VMs?

  - by symcbean

  I'm looking at the feasibility of providing remote access to multiple virtual machines. The VMs themselves will provide user desktops. To make best use of the available resources, I'd like the VMs to hibernate when the user disconnects. Which implies being able to start them up when a user connects. Ideally each user would 'own' a VM image - but if not then I'd require that the session was terminated. Obviously this would require the remote access protocol to be tied into the VM management. Is there anything out there to provide such functionality? (extra credit for open protocols! ;)

  Read the article

• ZFS on top of iSCSI

  - by Solipsism

  I'm planning on building out a file server using ZFS and BSD, and I was hoping to make it more expandable by attaching drives stored in other machines in the same rack via iSCSI (e.g., one machine is running ZFS, and others have iSCSI targets available to be connected to by the ZFS box and added to zpools). Looking for other people who have tried this has pretty much lead me to resources about exposing iSCSI shares on top of ZFS, but nothing about the reverse. Primarily I have the following questions: Is iSCSI over gigabit ethernet fast enough for this purpose, or would I have to switch to 10GbE to get decent performance? What would happen when one of the machines running iSCSI targets disconnects from the network? Is there a better way to do this that I just am not clever enough to have realized? Thanks for any help.

  Read the article

• WD 1TB Passport Essential not working on some USB ports

  - by user143863

  I have a strange situation here. I got a new Toshiba P850/04P laptop, there are 4 USB 3.0 ports, 2 on the right and 2 on the left. When I plug my WD 1TB Passport Essential into the 2 ports on the left, the drive keeps disconnecting and then connecting again, on and off. Sometimes it works well for 1 hour and then disconnects and even shows the "please format your drive" message. What is odd is: this WD 1TB Passport Essential works perfectly on those 2 ports on the right side. It has been working fine on all other PCs and laptops. Another 500 GB WD passport can work with the USB ports on the left (the ones 1TB can not), also all other devices can work with all 4 ports. I am really confused! Does anyone know what the problem could be?

  Read the article

• Getting Xbox Live via a wired network with my laptop that has internet access wirelessly

  - by Alex Franco

  I'm running the latest version (as of yesterday anyways) of Ubuntu Desktop 64bit, but installed on my laptop if it makes a difference. I had Windows 7 preinstalled when i bought it and it worked fine with the wireless from my house and bridging the connection with a LAN to my xbox for Live. Now with Ubuntu I tried the same setup, but I'm unfamiliar with Ubuntu so I didn't get far. Best I got so far is wireless internet on my laptop and a wired connection to the xbox that continually connects and disconnects. Heres my network settings. if theres fields not included its because theyre empty on mine or theyre my MAC address or network password Wireless Network 1 settings: Connect Automatically: Checked. Available to all Users: Checked Wireless: SSID: Franco's Mode: Infrastructure MTU: Automatic IPv4 Settings: Method: Automatic (DHCP) IPv6 Settings: Method: Automatic Wired Network 1: Connect Automatically: Checked Available to all Users: Checked Wired: MTU: Automatic IPv4 Settings: Method: Automatic (DHCP) IPv6 Settings: Method: Automatic Any help would be greatly appreciated. EDIT: 6:26pm It seems to be staying connected now. Doing the Network test on my xbox it pickups the network, but cannot detect any PC. Restarting the Xbox, however, leaves my computer unable to connect bringing up the Wire Network disconnected 'blip' every minute or so again. Before I had restarted the Xbox it said "Connected 100 MB/s". Now it only says "connecting". I did have my computer and xbox on in this Wired Network Disconnected blip cycle for a long period of time so it may have finally connected, just without the ability to detect my laptop. I left for 2 hours or so in the middle of typing up the original question. I finished posting this when i got back and then tried to mess with it a bit again, in case youre wondering why i didnt include this before... I've said too much. Forgive my long-winded fingers :p

  Read the article

• Beyond S&OP: Integrated Business Planning

  - by Paul Homchick

  In most corporations, planning is done at the department level — leaving disconnects and gaps across different departments. Finance sets revenue and profit goals with minimum validation from Manufacturing that the company has the resources, material, capacity, or demand to reach these goals. On the operations side, Manufacturing is developing plans to balance demand and supply but seldom knows if the resulting "plan" will meet the budgets on which the company's revenue and profit goals are based. The Sales department agrees to quotas that meet Finance's revenue goals without a complete understanding of what manufacturing can deliver. Integrated Business Planning (IBP) bridges these gaps in corporate planning systems. Integrated Business Planning integrates the financial planning provided by EPM systems with operations planning provided by Sales and Operations Planning solutions. This means that revenue goals and budgets are validated against a bottom-up operating plan, and that the operating plan is reconciled against financial goals. When detailed changes are made to the operations plan, planners can immediately see the big picture impact of the changes. IBP also addresses one the CFO's big concerns—the reliability of the revenue forecast. Operating plans are updated daily or weekly from a precise forecast based on current market conditions. These updated plans are then made available so that financial analysts are working with data that best represents what is going to happen - not what they projected would happen based on last quarter's data. For a discussion in more depth, see my article: Improve Reliability of Financial Forecasts with Integrated Business Planning in Supply & Demand Chain-Executive Magazine.

  Read the article

• Beyond S&OP: Integrated Business Planning

  - by Paul Homchick

  In most corporations, planning is done at the department level — leaving disconnects and gaps across different departments. Finance sets revenue and profit goals with minimum validation from Manufacturing that the company has the resources, material, capacity, or demand to reach these goals. On the operations side, Manufacturing is developing plans to balance demand and supply but seldom knows if the resulting "plan" will meet the budgets on which the company's revenue and profit goals are based. The Sales department agrees to quotas that meet Finance's revenue goals without a complete understanding of what manufacturing can deliver. Integrated Business Planning (IBP) bridges these gaps in corporate planning systems. Integrated Business Planning integrates the financial planning provided by EPM systems with operations planning provided by Sales and Operations Planning solutions. This means that revenue goals and budgets are validated against a bottom-up operating plan, and that the operating plan is reconciled against financial goals. When detailed changes are made to the operations plan, planners can immediately see the big picture impact of the changes. IBP also addresses one the CFO's big concerns—the reliability of the revenue forecast. Operating plans are updated daily or weekly from a precise forecast based on current market conditions. These updated plans are then made available so that financial analysts are working with data that best represents what is going to happen - not what they projected would happen based on last quarter's data. For a discussion in more depth, see my article: Improve Reliability of Financial Forecasts with Integrated Business Planning in Supply & Demand Chain-Executive Magazine.

  Read the article

• How do I disable all lid close processes?

  - by Mat

  I want to be able to close my laptop without Ubuntu registering it. I've been looking everywhere and I've found plenty of people with the same problem but no real solutions. Obviously I have set the lid close setting to 'do nothing' for both AC and battery, but when I close the lid it still blanks the screen, disconnects from external monitors, and brings up the lock screen when I reopen it. Some people have suggested disabling the lock screen, but this doesn't stop the screen blanking and external displays disconnecting, and I don't want to disable the lock anyway, as I still want it when I tell Ubuntu to lock or sleep or whatever else. Others have suggested it's something to do with ACPI support, but I have tried changing some ACPI scripts, and even removed them completely (e.g. /etc/acpi/lid.sh and /etc/acpi/events/lidbtn) and it makes no difference. There must be a bit of code somewhere that can just be removed or commented out or altered to prevent any lid close actions - does anyone know where? I know this has been asked before, but I'm getting really frustrated with this problem. I'm disappointed to say that I'm actually using Windows 7 more often just because it's quite happy to completely ignore the closed lid. So I just wanted to check, are we any closer to a real solution for this problem?

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• Ubuntu 12.04 Freezes w/ Ethernet Unplugged + Wireless Drops (Acer Aspire 5516)

  - by Grand Master T

  Ubuntu 12.04-12.10 32/64 freezes or won't boot if the Ethernet cable is unplugged and will not hold a wireless connection. Here is my scenario... Laptop: Acer Aspire 5516 Wireless card: Broadcom BCM4312 Ubuntu 12.04 32/64 Issues Unity 3d won't load without the Ethernet cable plugged in. If I let it load with Ethernet plugged in, it will freeze once I disconnect the cable. Unity 2d will load without the Ethernet cable plugged. In Unity 2d, wireless cannot hold a connection. I can connect to a Wireless network, but when I try to use it (i.e. open a browser), it disconnects. I can reconnect by disabling wireless (uncheck Enable Wireless), re-enable wireless, and reconnect. But, it will disconnect again once I start using it. Ubuntu 12.10 Issues Since 12.10 only gives me the option to load 3d (I assume), I experience the same thing as the first issue in 12.04. Attempted Solutions Enable networking/LAN in BIOS Set LAN first in boot priority in BIOS Remove STA wireless driver (bcmwl-kernel-source) and install b43 low power driver (firmware-b43-lpphy-installer). Remove default Network Manager and install Wicd. So far, I have had no luck with fixing this issue. Does anyone have any further suggestions?

  Read the article

• Update Manager got stuck (but not frozen) while installing downloaded updates. What should I do?

  - by WarriorIng64

  I have just gotten my Ubuntu 12.04 LTS desktop computer reassembled after a trip back home and connected it to my parent's wireless Internet connection. The connection seems quite shaky (disconnects half the time, likely an ongoing issue with the wireless card I have installed), and it struggled to download updates because of the constant interruptions. Eventually, it managed to download the updated packages and started installing them. I got up and left it to do its work. When I came back, I saw it was still having trouble staying connected to the wireless (no surprise there), but then I noticed that it seemed like Update Manager had stopped making progress on the installation. I opened the Details pane to see what it was last doing: My guess was that the installation script for flashplugin-installer couldn't complete the download until I stabilized the Internet connection. I hooked my Ubuntu laptop up to my desktop via Ethernet and shared its wireless connection using this guide, and as I am typing this now from my desktop you can see that the connection issue was successfully worked around. However, even with a stable connection established, Update Manager seems "stuck" at its current position and won't go any further. It's not totally frozen, but I can't do anything beyond open/close the Details pane as the Cancel button is grayed out. I know it can cause big problems if updates are stopped during installation, but I'm at a loss as to how this situation should be handled. I'm sure it should finish normally if I can just find a way to restart Update Manager, but the question is how this should be approached. How can I safely get my updates to finish installing?

  Read the article

• Wifi won't connect to certain networks

  - by Dave M G

  As I write this, I'm in a coffee shop on my laptop, and I am trying to connect to the free wifi network they offer. Every time I select their network from the wifi applet drop down menu, it connects for a second and then disconnects. At the same time, I have my Android phone with me, and it connects to the coffee shop's network without problem. There are a couple of people around me also using the same network with no issues. I asked the staff to check and as far as they can tell there is no problem with their router or anything. I have tried rebooting, but it has not made a difference. I have double and triple checked that I am using the correct WEP password. As an added wrinkle, when I connect to another network, it seems to connect (although I can't use them because they are paid gateway services). So I'm able to ask this question now because I have tethered my laptop to my phone, but it's slow and a workaround, not a solution. All indications are that it's a problem with my computer against this one network. Why would that be and how can I fix it?

  Read the article

• Detect aborted connection during ASIO request

  - by Tim Sylvester

  Is there an established way to determine whether the other end of a TCP connection is closed in the asio framework without sending any data? Using Boost.asio for a server process, if the client times out or otherwise disconnects before the server has responded to a request, the server doesn't find this out until it has finished the request and generated a response to send, when the send immediately generates a connection-aborted error. For some long-running requests, this can lead to clients canceling and retrying over and over, piling up many instances of the same request running in parallel, making them take even longer and "snowballing" into an avalanche that makes the server unusable. Essentially hitting F5 over and over is a denial-of-service attack. Unfortunately I can't start sending a response until the request is complete, so "streaming" the result out is not an option, I need to be able to check at key points during the request processing and stop that processing if the client has given up.

  Read the article

• How to rewrite to a virtual directory with a different application

  - by Eytan Levit

  Hi, I have a CMS application that manages multiple websites, today whenever i change the codebehind of one of these websites - i have to rebuild the dll for all websites, deploy it - this disconnects all current sessions and is really bad. The iis is configured to listen to all domain requests, if the request is to one of the websites' domain , the application rewrites it, or example, if someone requests for http://www.example.com, and example.com is configured in the application to be website 12, it is rewritten to http://www.example.com/websites/12/default.aspx. This is done for all websites. We want to seperate the dlls of the websites from each other, and from the main CMS, we have a virtual directory to each websites, but when trying to rewrite to it, we discover that IIS support this (we get an "Could not load type '_12._Default'". error). How can we perform this rewrite so it does rewrite to virtual directories, or if anyone has any other solution for the initial dll seperation problem. Thanks in advance

  Read the article

• IE7 Times Out Debugging ASP.Net Page

  - by Eric J.

  My issue is similar to ASP.NET Debugging Timing out with IIS except that I'm using the built-in ASP.Net Development Server with VS 2010. If I pause for more than about 10 seconds in the debugger, IE7 "disconnects" from the web server with the error message Internet Explorer cannot display the webpage However, unlike in the similar question, the debugger is still running. If I refresh the browser it will post that refresh to the server and I can debug the page from the top again. Is it possible to configure things so that IE7 waits (much) longer before giving up? If it makes a difference, I'm launching IE using the "Start external program" option and passing a localhost URL as the command line argument (since Chrome is my default browser). I also specify a specific port.

  Read the article

• jQuery UI - Accordion Display issues

  - by Dave Kiss

  My accordion is working properly, but I'm having a few CSS and JS issues that are prohibiting it from displaying correctly. http://jsfiddle.net/frEWQ/ The JS is applying .ui-corners-all to the H3 before the "kwick" div below it has finished collapsing, giving an odd cut-off border during the animation The margin-bottom applied to the "kwick" div to give spacing between each tab disappears when the tab is set to display:none, getting rid of the spacing... but I can't apply the margin-bottom to the header because it disconnects the header from the "kwick" div below it. Any suggestions? Modification to the JS/CSS? Thanks

  Read the article

• How to tell the parent that the thread is done in C++ using pthreads ?

  - by milleroff

  Hi. I have a TCP Server application that serves each client in a new thread using POSIX Threads and C++. The server calls "listen" on its socket and when a client connects, it makes a new object of class Client. The new object runs in its own thread and processes the client's requests. When a client disconnects, i want some way to tell my main() thread that this thread is done, and main() can delete this object and log something like "Client disconnected". My question is, how do i tell to the main thread, that a thread is done ?

  Read the article

• RMI client tracking

  - by 0000

  I'm building a Client / Server app that has some very specific needs. There are 2 kinds of servers: the first kind provide most of the remote procedures and clients connect to these directly, while the second kind is a single server that should keep track of what users are active (clients) and how many servers of the first kind are active when a method is called. The main thing is that the monitor should ONLY connect to the servers and not the clients directly. My first idea was to implement a simple login/logout rmi method when a client connects/ disconnects and keep track of those in a list but the main problem is when a client or server end abnormally. For example, if a client goes offline abruptly the server should somehow be notified and update the list accordingly, while if a server goes out all of the clients connected to it should be marked as not active in the control server. Any ideas of how to implement this functionality would be appreciated.

  Read the article

• C++ Multithreaded server help

  - by kisplit

  Hello all, I'm working on a multithreaded server in c++ using boost-asio. Currently a design problem I'm running into deals with erasing a connection. I have a single server instance which holds a vector of connection objects. These connections receive commands which I parse. One command in particular deals with sending data to ALL connections in my vector. Now when a connection disconnects I'm currently erasing this connection from the vector and calling the destructor. It seems like I'm going to run into problems when someone 'SendAll' at the same time someone 'Disconnect'. Could anyone recommend a better design or just point me in the right direction? Any help greatly appreciated. Thanks

  Read the article

• router gets disconnected once I terminate my SIP application

  - by TacB0sS

  Hey, Here is an interesting one, I have a SIP VoIP application which is able to register to the PBX server, and I can invite and see the user call on the callee end receiving an Invite, and on the caller end I see the Ringing response... now here is interesting part, if I close my application with out any notification to the server my router disconnects and restart, after a short while (30 - 150 sec). I could fix that if I would complete the ACK BYE process, but I'm just wondering why does my router hangs up? any ideas?

  Read the article

• Why can I not have two SocketServers bound to two different ports in the same application?

  - by uriDium

  I am using .Net 3.5 and Windows XP not sure if any more information is needed. I have an application that creates a socket, binds to a port and starts listening. A client comes and connects and then disconnects no problem. It can then reconnect no problem. If I have to sockets each listening on a different (e.g. 50 000 and 55 000) then it will accept the connection but it will not allow a reconnect. I will post source code if needed but I am assuming that it is just something simple that I am not catching.

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10  | Next Page >