Search Results

Search found 231 results on 10 pages for 'networkmanager'.

Page 7/10 | < Previous Page | 3 4 5 6 7 8 9 10  | Next Page >

• Unable to connect to internet

  - by Peter Schriver

  I just upgraded to 12.10. Everything appears to go well but I am unable to connect to the Internet. The LAN is fine and I can view my shared files but no e-mail or access to web pages. My other computer which is running 12.04 or older seems to connect fine. I only upgraded one to make sure things would be ok. I am currently connecting fine with a wireless Windows laptop. Output from cat /etc/resolv.conf # Generated by NetworkManager nameserver 127.0.0.1

  Read the article

• Unstable Wifi and Spontaneous Low-graphic Error with Pavilion DV4

  - by Constant Dean

  I've been having numerous problems with connectivity through WiFi. It had been working for a few days and now it doesn't. On top of that around 40% of every time I turn on the laptop it shows "System running in low-graphics" error and I'm unable to view the desktop (sometimes not even able to access terminal), therefore having to manually power-down until it finally works. I use Ubuntu 12.10. nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: r8169 State: connected Default: yes HW Address: 84:34:97:6B:2E:D7 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.10 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 DNS: 68.237.161.12 - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: rt2800pci State: unavailable Default: no HW Address: 68:94:23:50:A5:D9 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points

  Read the article

• how to find 3g modem signal strength with out AT commands?

  - by neckTwi

  when i try to find signal strength of my modem using AT+CSQ, the usb device is locked by the network manager. To find the signal strength with AT+CSQ i have to first disable network connection using #nmcli nm wwan off to unlock the device inode /dev/ttyUSBX. Is there any nmcli option to get signal strength or any other option? EDIT The gdbus object for NetworkManager don't have any method like getSignalStrength. Network manager is locking device file preventing to use AT commands. nm-applet was able to display signal strength in system tray. so there should be a way to get signal strength form network manager! nmcli is command line counter part of nm-applet. Can i get signal strength using nmcli? nothing about signal strength is mentioned in its man pages.

  Read the article

• How can I have my VPN connect automatically when the wireless connects?

  - by ams

  I have a working VPN connection using NetworkManager, OpenConnect, and the network-manager-openconnect-gnome package, but I have to start it manually every time I connect to a network, and I have to enter my password manually each time. How can I get it to connect automatically, and remember my password (securely)? I have checked the 'Connect Automatically' box on the Configure VPN page, but this seems to have no effect. I've also got the 'Start connecting automatically' box checked in the pop-up box, and that does avoid the need to press the connect button in that window, but seems to have no part in kicking off the whole process in the first place. There is no option to remember the password in the window, but maybe there's one somewhere else?

  Read the article

• USC gives "failed to download package files" message - how to fix?

  - by DrT

  Trying to download a program (Advanced Settings aka Gnome Tweak tool) from USC and getting this error "Failed to Download Package Files: check your internet connection". Under details is info: Failed to fetch http://ch.archive.ubuntu.com/ubuntu/pool/main/n/network-manager/gir1.2-networkmanager-1.0_0.9.1.90-0ubuntu4_i386.deb 404 Not Found Question: how to fix? Note: I tried downloading another program from USC (GnuCash) and it worked fine. And my internet connect is working fine (able to surf the web, etc) and Ubuntu is fully up to date and is able to download updates. It seems to be a problem just getting the "Advanced Settings" program. (Ubuntu 11.10).

  Read the article

• ERROR while getting interface

  - by user284391

  I have installed the latest version of aircrack-ng, but when i run this code, sudo airmon-ng start wlan0 I get this. sudo airmon-ng start wlan0 Found 4 processes that could cause trouble. If airodump-ng, aireplay-ng or airtun-ng stops working after a short period of time, you may want to kill (some of) them! -e PID Name 463 avahi-daemon 475 avahi-daemon 683 NetworkManager 756 wpa_supplicant Interface Chipset Driver wlan0 Broadcom wl - [phy0]mon0: ERROR while getting interface flags: No such device (monitor mode enabled on mon0) Is there anyone who could help me get this problem solved please.

  Read the article

• Connect to a VPN from a Virtual Machine

  - by kaharas

  I am running an Ubuntu ditro inside a VMWare virtual machine with a bridged connection on a windows 7 host. What I am trying to do is to have the virtual machine connect to a VPN, but I'm not having much success. At first, the system was using wicd, but I replaced it with network-manager who's supposed to have OpenVPN support. The problem is, even tho i've purged the wicd installation, there're connections shown in the network manager, and still, I'm able to access the net. I've also added the openvpn data in the network manager tab, but it's shown as never used. PS: when I try to stop and start the NetworkManager service, an error message pops up telling me that there's not such a service, but apt-get tells me i've already installed it...

  Read the article

• Getting wifi working on 14.04

  - by user286114

  I have installed Ubuntu 14.04 on my laptop. When I plug in the ethernet cable the internet works fine, but I can't see any wireless network in the networking manager. The wifi switch is definitely on on my laptop! It's a Dell XPS M1330. I'm not sure what the network card is - how can I find out? nm-tool gives me this: NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: tg3 State: connected Default: yes HW Address: 00:23:AE:28:FE:A2 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.26 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.254 DNS: 192.168.1.254

  Read the article

• rpm rollback ignoring rpms - no error output

  - by John H

  Issue rpm rollback is not working with a set of repackaged rpms created in the last couple days, but does work with more recent ones. [root@host1 repackage]# ls -l zsh-4.2.6-* -rw-r--r-- 1 root root 1788283 Apr 10 2011 zsh-4.2.6-3.el5.i386.rpm -rw-r--r-- 1 root root 1788691 Aug 18 04:38 zsh-4.2.6-5.el5.i386.rpm [root@host1 repackage]# rpm -q zsh zsh-4.2.6-6.el5 [root@host1 repackage]# rpm --test -Uvh --rollback 'Aug 18 01:00' [root@host1 repackage]# rpm -e zsh [root@host1 repackage]# [root@host1 repackage]# ls -l zsh* -rw-r--r-- 1 root root 1788283 Apr 10 2011 zsh-4.2.6-3.el5.i386.rpm -rw-r--r-- 1 root root 1788691 Aug 18 04:38 zsh-4.2.6-5.el5.i386.rpm -rw-r--r-- 1 root root 1789064 Aug 20 09:06 zsh-4.2.6-6.el5.i386.rpm [root@host1 repackage]# cp zsh-4.2.6-6.el5.i386.rpm /tmp [root@host1 repackage]# rpm --test -Uvh --rollback 'Aug 18 01:00' Rollback packages (+1/-0) to Mon Aug 20 09:02:16 2012 (0x50323558): Preparing... ########################################### [100%] Cleaning up repackaged packages: Removing /var/spool/repackage/zsh-4.2.6-6.el5.i386.rpm: [root@host1 repackage]# ls -l zsh-4.2.6-* -rw-r--r-- 1 root root 1788283 Apr 10 2011 zsh-4.2.6-3.el5.i386.rpm -rw-r--r-- 1 root root 1788691 Aug 18 04:38 zsh-4.2.6-5.el5.i386.rpm [root@host1 repackage]# cp /tmp/zsh-4.2.6-6.el5.i386.rpm . [root@host1 repackage]# rpm -Uvh --rollback 'Aug 18 01:00' Rollback packages (+1/-0) to Mon Aug 20 09:06:05 2012 (0x5032363d): Preparing... ########################################### [100%] 1:zsh ########################################### [ 50%] Cleaning up repackaged packages: Removing /var/spool/repackage/zsh-4.2.6-6.el5.i386.rpm: [root@host1 repackage]# rpm --test -Uvh --rollback 'April 9' [root@host1 repackage]# Now, if I run my test commands with -Uvvh I get debug messages to stderror which shows me that rpm reads each of the rpm files in /var/spool/repackage. The only interesting bit is the "expected size" but after searching, the expected size should be different, as it records the files as they are on the filesystem. D: opening db environment /var/lib/rpm/Packages joinenv D: opening db index /var/lib/rpm/Packages rdonly mode=0x0 D: locked db index /var/lib/rpm/Packages D: opening db index /var/lib/rpm/Installtid rdonly mode=0x0 D: opening db index /var/lib/rpm/Pubkeys rdonly mode=0x0 D: read h# 769 Header sanity check: OK D: ========== DSA pubkey id 53268101 37017186 (h#769) D: read h# 32 Header V3 DSA signature: OK, key ID 37017186 D: read h# 40 Header V3 DSA signature: OK, key ID 37017186 ... D: read h# 1753 Header V3 DSA signature: OK, key ID 37017186 D: Expected size: 3628918 = lead(96)+sigs(344)+pad(0)+data(3628478) D: Actual size: 3583695 D: /var/spool/repackage/Deployment_Guide-en-US-5.2-11.noarch.rpm: Header V3 DSA signature: OK, key ID 37017186 D: Expected size: 1100789 = lead(96)+sigs(344)+pad(0)+data(1100349) D: Actual size: 1109281 D: /var/spool/repackage/NetworkManager-0.7.0-10.el5_5.2.i386.rpm: Header V3 DSA signature: OK, key ID 37017186 D: Expected size: 1098167 = lead(96)+sigs(344)+pad(0)+data(1097727) D: Actual size: 1106179 D: /var/spool/repackage/NetworkManager-0.7.0-9.el5.i386.rpm: Header V3 DSA signature: OK, key ID 37017186 D: Expected size: 84351 = lead(96)+sigs(344)+pad(0)+data(83911) D: Actual size: 85378 ... D: Expected size: 1788276 = lead(96)+sigs(344)+pad(0)+data(1787836) D: Actual size: 1788691 D: /var/spool/repackage/zsh-4.2.6-5.el5.i386.rpm: Header V3 DSA signature: OK, key ID 37017186 D: --- erase h#1758 D: closed db index /var/lib/rpm/Pubkeys D: closed db index /var/lib/rpm/Installtid D: closed db index /var/lib/rpm/Packages D: closed db environment /var/lib/rpm/Packages D: May free Score board((nil)) I am able to copy these rpms out of the repackage directory and if I run them through cpio, extract the files. I also tried backing up and rebuilding the rpm database - no change. System Information: RHEL 5.8 rpm 4.4.2.3 /etc/yum.conf tsflags=repackage /etc/rpm/macros %_repackage_all_erasures 1

  Read the article

• Setting up home DNS with Ubuntu Server

  - by Zeophlite

  I have a webserver (with static IP 192.168.1.5), and I want to have my machines on my local network to be able to access it without modifying /etc/hosts (or equivalent for Windows/OSX). My router has Primary DNS server 192.168.1.5 Secondary DNS server 8.8.8.8 (Google's public DNS). Nginx is set up to server websites externally as *.example.com Internally, I want *.example.local to point to the server. My webserver has BIND9 installed, but I'm unsure of the settings. I've been through various contradicting tutorials, and so most of my settings have been clobbered. I've stripped out the lines which I'm confused about. The tutorials I looked at are http://tech.surveypoint.com/blog/installing-a-local-dns-server-behind-a-hardware-router/ and http://ubuntuforums.org/showthread.php?t=236093 . They mostly differ on what should be put in /etc/bind/zones/db.example.local and /etc/bind/zones/db.192, so I've left the conflicting lines out below. Can someone suggest what the correct lines are to give my above behaviour (namely *.example.local pointing to 192.168.1.5)? /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.5 netmask 255.255.255.0 broadcast 192.168.1.255 gateway 192.168.1.254 /etc/hostname avalon /etc/resolv.conf # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN /etc/bind/named.conf.options options { directory "/var/cache/bind"; forwarders { 8.8.8.8; 8.8.4.4; }; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; /etc/bind/named.conf.local zone "example.local" { type master; file "/etc/bind/zones/db.example.local"; }; zone "1.168.192.in-addr.arpa" { type master; file "/etc/bind/zones/db.192"; }; /etc/bind/zones/db.example.local $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 5 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL /etc/bind/zones/db.192 $TTL 604800 @ IN SOA avalon.example.local. webadmin.example.local. ( 4 ; Serial, increment each edit 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; What do I need to add to the above files so that on a laptop on the internal network, I can type in webapp.example.local, and be served by my webserver? EDIT I made several changes to the above files on the webserver. /etc/network/interfaces (end of file) dns-nameservers 127.0.0.1 dns-search example.local /etc/bind/zones/db.example.local (end of file) @ IN NS avalon.example.local. @ IN A 192.168.1.5 avalon IN A 192.168.1.5 webapp IN A 192.168.1.5 www IN CNAME 192.168.1.5 /etc/bind/zones/db.192 (end of file) IN NS avalon.example.local. 73 IN PTR avalon.example.local. As a side note, my spare Win7 machine was able to connect directly to webapp.example.local, but for a Ubuntu 13.10 machine, I had to make the following changes as well (not on the webserver, but on a separate machine): /etc/nsswitch.conf before hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 after hosts: files dns /etc/NetworkManager/NetworkManager.conf before dns=dnsmasq after #dns=dnsmasq The issue remains that its not wildcard DNS, and so I have to add entries to /etc/bind/zones/db.example.local for webapp1, webapp2, ...

  Read the article

• How to configure wpa_supplicant on RHEL6?

  - by Yang Jy

  I am running a version of RHCE6 on my laptop. I uninstalled the default NetworkManager in order that I could configure the network all in the command line. The Ethernet part is okay, but I have problem bringing up the wireless interface. What I got is: Bringing up interface wlan0: Determining IP information for wlan0... failed; no link present. Check cable? I did exactly what this article says. I am not sure if it is because the article is obsolete or something else. Please help.

  Read the article

• ESXi 4.1 CentOS 6.X eth0 unnavailable

  - by L.K.

  I don't usually ask for help so directly, usually google have all i need but this time i'm seriously lost. Hope you can help me .s The thing is, i have a server with Vmware ESXi 4.1 and 5 already running and configured virtual servers, but whenever i try to make a new one on CentOS 6.X it leaves me without eth0 to be activated in any way. When installing CentOS, in the screen of localhost.localdomain i try by the button in the left down corner of the screen to make eth0 connect automatically but it tells me a NetworkManager Error: cannot start eth0. So...in command line once the CentOS is already installed, i have configured ifcfg-eth0 and manually tried to take up the eth0 but when i restart network service "Bringing up eth0: Failed" and sometimes even "shutting down eth0: Failed" Thanks in advance

  Read the article

• Slow internet using Arch Linux

  - by GZaidman

  after a week or so of using Arch Linux I cant access the internet - it takes around 5 mins to load google (most of the other websites just give me a timeout), pacman's downloading speed range between 5-2Kbs, and pinging google takes around 9Kms. I'm connected using wireless network (wifi card is Intel Ultimate 6300 and router is Edimax 6524n). Every other Windows machine that's connected to the network (and even the T410 running Windows) is fine, so the problem lies in Linux. So far, i checked the resolv.conf file (my router ip address is listed), and the hosts file (pretty much default), and I disabled the ipv6 module. None of that helped. PS: i'm using NetworkManager (but the problem still occurs when connecting using wicd) running on Gnome3. Thanks in advance for any help you can provide! EDIT: something really strange happens whenever I ping google: i get an unknown host 'google.com', but the bit rate from the card jumps at the exact second I ping google (so far, the bit rate jumped to 54Mb/s from 1Mb/s over the course of 4 pings).

  Read the article

• Multiple interfaces to one IP address?

  - by Delan Azabani

  At present, I have: a Netgear router with DHCP off at 192.168.0.1 my computer eth0 at 192.168.0.2 wlan0 at 192.168.0.2 The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation. If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected. Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).

  Read the article

• strange behaviour - dhclient needs to be run twice in order to connect to wireless

  - by splicer

  I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

  Read the article

• Configure Wireless Network Card

  - by Skizz

  I recently upgraded the wireless network card in my Ubuntu PC from an 802.11g to an 802.11n. Now, it can't see my router. It doesn't appear in the list of networks that is displayed when you click on the NetworkManager icon in Gnome. Other networks are listed and I have connected to them (no password required!). I'm using the Windows driver through ndiswrapper and it can see the card. I tested the card in a Windows PC and everything worked. The router's log doesn't show any messages coming from the wireless card. What have I done wrong? If you need any more information, just leave a comment and I'll get add it to the question.

  Read the article

• Ubuntu problem not connecting to wireless or wired network

  - by ToughPal

  I recently installed openvpn and things were working. But I got a weird screen after a few hours and on restart my wired and wireless connections are not working. Can someone help? cat /etc/network/interfaces auto lo iface lo inet loopback cat /etc/resolv.conf #Generated by NetworkManager Is there anything missing? I tried both wired and wireless and both are not working. Usually if I ever have a problem with wireless, the wired always work! My /etc/network/interfaces is looking wrong. Can you please send me yours? I am using ubuntu 9.10 and the internet was working correctly until today! Please help

  Read the article

• Disable Thunderbird "failed to connect" notifications

  - by The Electric Muffin

  My network manager doesn't start until I log in, so for the first ten seconds or so after I login I have no Internet connection. The problem is that I have Thunderbird set to automatically start on login, so it helpfully tells me it "failed to connect" every time I log in. Also, my Internet connection isn't too reliable, so I sometimes get those messages even when I'm supposedly connected. Is there any way to disable these notifications, while still allowing the ones about new mail? Computer info: Thunderbird 15.0 $ uname -a Linux [HOSTNAME REDACTED] 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Probably irrelevant: NetworkManager Version 0.9.0.1 (nm09 20120407) KDE Platform Version 4.8.4 (4.8.4)

  Read the article

• Gnome-Network-Manager Config File Migration

  - by Jorge

  I think I have an issue with gnome-network-manager, I used to have a lot of connections configured, Wireless, Wired and VPN. After upgrading to 12.04 (from 11.10) I lost every configuration. I realized that the configs that used to be saved in $HOME/.gconf/system/networking/connections now are being saved in /etc/NetworkManager/system-connections/. I don't know how to migrate my settings to the new config file format Can anybody help me? jorge@thinky:~$ sudo lshw -C network *-network description: Ethernet interface product: 82566MM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:1f:e2:14:5a:9b capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k firmware=0.3-0 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:fe000000-fe01ffff memory:fe025000-fe025fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 4965 AG or AGN [Kedron] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 61 serial: 00:21:5c:32:c2:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl4965 driverversion=3.2.0-23-generic-pae firmware=228.61.2.24 ip=192.168.2.103 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:df3fe000-df3fffff jorge@thinky:~$ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise jorge@thinky:~$ uname -a Linux thinky 3.2.0-23-generic-pae #36-Ubuntu SMP Tue Apr 10 22:19:09 UTC 2012 i686 i686 i386 GNU/Linux jorge@thinky:~$ dpkg -l | grep -i firm ii linux-firmware 1.79 Firmware for Linux kernel drivers

  Read the article

• can ping, but not SSH

  - by Matt

  So I have NetworkManager, connected to an AP on wlan1. I have wlan0 connected to a AdHoc network. I have Firestarter sharing my inet on the Adhoc. I have my ipod connected to wlan0, IP 10.42.43.101. wlan0 Link encap:Ethernet HWaddr ac:xx:12:81:7f:xx inet addr:10.42.43.1 Bcast:10.255.255.255 Mask:255.0.0.0 wlan1 Link encap:Ethernet HWaddr 00:xx:b3:98:f2:xx inet addr:10.0.1.61 Bcast:10.0.1.255 Mask:255.255.255.0 Now, I can ping my Jailbroken, SSH-enabled and running ipod touch: matt: ~ $ ping 10.42.43.101 PING 10.42.43.101 (10.42.43.101) 56(84) bytes of data. 64 bytes from 10.42.43.101: icmp_req=1 ttl=64 time=168 ms 64 bytes from 10.42.43.101: icmp_req=2 ttl=64 time=256 ms 64 bytes from 10.42.43.101: icmp_req=3 ttl=64 time=151 ms ^C --- 10.42.43.101 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 151.465/191.979/256.316/46.003 But I cannot SSH it: $ ssh [email protected] -vv OpenSSH_5.8p1 Debian-1ubuntu3, OpenSSL 0.9.8o 01 Jun 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.42.43.101 [10.42.43.101] port 22. It just stays there till I ^C it.. Here's my routing: $ ip route show 10.0.1.0/24 dev wlan1 proto kernel scope link src 10.0.1.61 metric 2 10.0.1.0/24 dev wlan1 proto kernel scope link src 10.0.1.61 metric 319 169.254.0.0/16 dev vboxnet0 proto kernel scope link src 169.254.128.223 metric 204 10.0.0.0/8 dev wlan0 proto kernel scope link src 10.42.43.1 default via 10.0.1.1 dev wlan1 proto static default via 10.0.1.1 dev wlan1 metric 319

  Read the article

• How do I restore a backup of my keyring (containing ssh key passprases, nautilus remote filesystem passwords and wifi passwords)?

  - by con-f-use

  I changed the disk on my laptop and installed Ubuntu on the new disk. Old disk had 12.04 upgraded to 12.10 on it. Now I want to copy my old keyring with WiFi passwords, ftp passwords for nautilus and ssh key passphrases. I have the whole data from the old disk available (is now a USB disk and I did not delete the old data yet or do anything with it - I could still put it in the laptop and boot from it like nothing happend). The old methods of just copying ~/.gconf/... and ~/.gnome2/keyrings won't work. Did I miss something? 1. Edit: I figure one needs to copy files not located in the users home directory as well. I copied the whole old /home/confus (which is my home directory) to the fresh install to no effect. That whole copy is now reverted to the fresh install's home directory, so my /home/confus is as it was the after fresh install. 2. Edit: The folder /etc/NetworkManager/system-connections seems to be the place for WiFi passwords. Could be that /usr/share/keyrings is important as well for ssh keys - that's the only sensible thing that a search came up with: find /usr/ -name "*keyring* 3. Edit: Still no ssh and ftp passwords from the keyring. What I did: Convert old hard drive to usb drive Put new drive in the laptop and installed fresh version of 12.10 there Booted from old hdd via USB and copied its /etc/NetwrokManager/system-connections, ~/.gconf/ and ~/.gnome2/keyrings, ~/.ssh over to the new disk. Confirmed that all keys on the old install work Booted from new disk Result: No passphrase for ssh keys, no ftp passwords in keyring. At least the WiFi passwords are migrated.

  Read the article

• Ubuntu 12.04 connected to wireless network but internet not working

  - by A.J.

  I can connect to my house's wireless network just fine, but when I'm connected I can't browse the web. Firefox starts connecting to a site and then just poops out. This doesn't happen on my roommates' computers (running Windows) or on our 3DSes, so I know it's just my laptop. I already tried sudo dhclient -r sudo dhclient sudo ifconfig eth0 down sudo ifconfig eth0 up Results of a few commands I was asked to run in comments: ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. ^C --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (173.194.33.38) 56(84) bytes of data. --- google.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1006ms nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 88:AE:1D:6B:4E:E7 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off - Device: wlan0 [JUSTICE] ----------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: connected Default: yes HW Address: 1C:65:9D:65:C6:31 Capabilities: Speed: 1 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) HOME-9B18: Infra, 00:26:F3:53:9B:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 34 WPA WPA2 cougdad48 Network: Infra, 60:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 22 WPA2 cougdad48 Guest Network: Infra, 66:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA2 belkin.ade: Infra, 94:44:52:FF:8A:DE, Freq 2457 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 *JUSTICE: Infra, 00:24:01:7B:9F:7E, Freq 2462 MHz, Rate 54 Mb/s, Strength 88 WEP CenturyLink: Infra, B2:B2:DC:8E:E2:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 IPv4 Settings: Address: 192.168.0.11 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 (JUSTICE is my home's network.) ping -c 2 198.168.0.1 PING 198.168.0.1 (198.168.0.1) 56(84) bytes of data. --- 198.168.0.1 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms

  Read the article

• Can't connect to hidden network with BCM4313

  - by poomerang

  The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

  Read the article

• Can't connect to or see my wifi ssid

  - by ant

  Today I installed ubuntu 12.04 on my laptop. I am unable to see my home SSID or even connect to it. I've tried to connect as a hidden SSID but I always get prompted for authorization although my key is correct. I'm in in Europe but my laptop is from US. I'm not sure if that is relevant. I've read around this site and saw something that has to do with setting the channel above 11. I'm not sure I did that correctly I did this : How to use Wi-Fi channels above 11? Did't help. I'm able to connect with cable but not via wifi either windows or linux. Other devices in my home can connect without any issues, even the kindle. Here is the screenshot from my router : Here is some additional info : lspci | grep -i network 08:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01) lspci -nnk | grep -A2 0280 08:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Hewlett-Packard Company U98Z062.10 802.11bgn Wireless Half-size Mini PCIe Card [103c:303f] Kernel driver in use: ath9k m-tool NetworkManager Tool State: connected (global) Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: disconnected Default: no HW Address: 90:4C:E5:38:79:0D Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes I'm not sure what to do next. Any suggestions?

  Read the article

• Sharing an internet connection through the Ethernet port

  - by Bob Cunningham

  I have a small living room PC (Bohica, running fully-updated Ubuntu 10.10/Maverick) connected to my HDTV that I use for web browsing and media streaming. It connects via WiFi (wlan0) to my Fedora server (Snafu) that in turn connects to the internet. I use static addressing, and everything has been working fine. I just got a Blu-ray player, and I'd like to give it wired network access to the internet via Bohica's available wired ethernet port (eth0). So far, I haven't been to get eth0 and the network configured to get the Blu-ray player talking to the internet. Here's my wlan0 configuration: ip4 addr: 192.168.0.100 mask: /24 (255.255.255.0) gateway: 192.168.0.4 (fedora box) The Blu-ray player is set to an IP of 192.168.0.98/24, with the same gateway as above. I want eth0 set to an IP of 192.168.0.99/24, but when I do this using nm-connection-editor I lose internet access (the system tries to use eth0 as the default internet access interface). How do I get my blu-ray player to talk to the internet through Bohica, and do so without disrupting my current (working) network? Thanks. Edit: Here's the relevant output from nm-tool with the Blu-ray player connected: $ nm-tool NetworkManager Tool State: connected - Device: eth0 Type: Wired Driver: forcedeth State: disconnected Default: no HW Address: 90:FB:A6:2C:94:32 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on - Device: wlan0 [wlan0] Type: 802.11 WiFi Driver: ndiswrapper State: connected Default: yes HW Address: 00:26:5A:C0:D0:05 IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.4

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10  | Next Page >