Search Results

Search found 163 results on 7 pages for 'tf rz'.

Page 7/7 | < Previous Page | 3 4 5 6 7 

• usb_modeswitch not switching

  - by deniz

  After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

  Read the article

• How to Troubleshoot TFS Build Server Failure?

  - by Tarun Arora

  Ever found your self in this helpless situation where you think you have tried every possible suggestion on the internet to bring the build server back but it just won’t work. Well some times before hunting around for a solution it is important to understand what the problem is, if the error messages in the build logs don’t seem to help you can always enable tracing on the build server to get more information on what could possibly be the root cause of failure. In this blog post today I’ll be showing you how to enable tracing on, - TFS 2010/11 Server - Build Server - Client Enable Tracing on Team Foundation Server 2010/2011 On the Team Foundation Server navigate to C:\Program Files\Microsoft Team Foundation Server 2010\Application Tier\Web Services, right click web.config and from the context menu select edit.          Search for the <appSettings> node in the config file and set the value of the key ‘traceWriter’ to true.          In the <System.diagnostics> tag set the value of switches from 0 to 4 to set the trace level to maximum to write diagnostics level trace information.          Restart the TFS Application pool to force this change to take effect. The application pool restart will impact any one using the TFS server at present. Note - It is recommended that you do not make any changes to the TFS production application server, this can have serious consequences and can even jeopardize the installation of your server.          Download the Debug view tool from http://technet.microsoft.com/en-us/sysinternals/bb896647.aspx and set it to capture “Global Events”. Perform any actions in the Team Explorer on the client machine, you should be able to see a series of trace data in the debug view tool now.         Enable Tracing on Build Controller/Agents Log on to the Build Controller/Agent and Navigate to the directory C:\Program Files\Microsoft Team Foundation Server 2010\Tools         Look for the configuration file ‘TFSBuildServiceHost.exe.config’ if it is not already there create a new text file and rename it to ‘TFSBuildServiceHost.exe.config’         To Enable tracing uncomment the <system.diagnostics> and paste the snippet below if it is not already there. <configuration> <system.diagnostics> <switches> <add name="BuildServiceTraceLevel" value="4"/> </switches> <trace autoflush="true" indentsize="4"> <listeners> <add name="myListener" type="Microsoft.TeamFoundation.TeamFoundationTextWriterTraceListener, Microsoft.TeamFoundation.Common, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" initializeData="c:\logs\TFSBuildServiceHost.exe.log" /> <remove name="Default" /> </listeners> </trace> </system.diagnostics> </configuration> The highlighted path above is where the Log file will be created. If the folder is not already there then create the folder, also, make sure that the account running the build service has access to write to this folder.         Restart the build Controller/Agent service from the administration console (or net stop tfsbuildservicehost & net start tfsbuildservicehost) in order for the new setting to be picked up.         Enable TFS Tracing on the Client Machine On the client machine, shut down Visual Studio, navigate to C:\Program Files\Microsoft Visual Studio 10.0\Common 7\IDE          Search for devenv.exe.config, make a backup copy of the config file and right click the file and from the context menu select edit. If its not already there create this file.          Edit devenv.exe.config by adding the below code snippet before the last </configuration> tag <system.diagnostics> <switches> <add name="TeamFoundationSoapProxy" value="4" /> <add name="VersionControl" value="4" /> </switches> <trace autoflush="true" indentsize="3"> <listeners> <add name="myListener" type="Microsoft.TeamFoundation.TeamFoundationTextWriterTraceListener,Microsoft.TeamFoundation.Common, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" initializeData="c:\tf.log" /> <add name="perfListener" type="Microsoft.TeamFoundation.Client.PerfTraceListener, Microsoft.TeamFoundation.Client, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a"/> </listeners> </trace> </system.diagnostics> The highlighted path above is where the Log file will be created. If the folder is not already there then create the folder. Start Visual Studio and after a bit of activity you should be able to see the new log file being created on the folder specified in the config file. Other Resources Below are some Key resource you might like to review. I would highly recommend the documentation, walkthroughs and videos available on MSDN.   Thank you for taking the time out and reading this blog post. If you enjoyed the post, remember to subscribe to http://feeds.feedburner.com/TarunArora. Have you come across an interesting one to one with the build server, please share your experience here. Questions/Feedback/Suggestions, etc please leave a comment. Thank You! Share this post : CodeProject

  Read the article

• OpenGL-ES Texture Mapping. Texture is reversed?

  - by Feet

  I am trying to get my head around Texture mapping, I thought I had it the other day after asking this. However, I am having some trouble with my texture coordinates being flipped from what I am expecting. I am loading my texture like so int[] textures = new int[1]; gl.glGenTextures(1, textures, 0); _textureID = textures[0]; gl.glBindTexture(GL10.GL_TEXTURE_2D, _textureID); Bitmap bmp = BitmapFactory.decodeResource( _context.getResources(), R.drawable.die_1); GLUtils.texImage2D(GL10.GL_TEXTURE_2D, 0, bmp, 0); gl.glTexParameterx(GL10.GL_TEXTURE_2D, GL10.GL_TEXTURE_MIN_FILTER, GL10.GL_LINEAR); gl.glTexParameterx(GL10.GL_TEXTURE_2D, GL10.GL_TEXTURE_MAG_FILTER, GL10.GL_LINEAR); bmp.recycle(); My cube is this float vertices[] = { // Front face -width, -height, depth, // 0 width, -height, depth, // 1 width, height, depth, // 2 -width, height, depth, // 3 // Back Face width, -height, -depth, // 4 -width, -height, -depth, // 5 -width, height, -depth, // 6 width, height, -depth, // 7 // Left face -width, -height, -depth, // 8 -width, -height, depth, // 9 -width, height, depth, // 10 -width, height, -depth, // 11 // Right face width, -height, depth, // 12 width, -height, -depth, // 13 width, height, -depth, // 14 width, height, depth, // 15 // Top face -width, height, depth, // 16 width, height, depth, // 17 width, height, -depth, // 18 -width, height, -depth, // 19 // Bottom face -width, -height, -depth, // 20 width, -height, -depth, // 21 width, -height, depth, // 22 -width, -height, depth, // 23 }; short indices[] = { // Front 0,1,2, 0,2,3, // Back 4,5,6, 4,6,7, // Left 8,9,10, 8,10,11, // Right 12,13,14, 12,14,15, // Top 16,17,18, 16,18,19, // Bottom 20,21,22, 20,22,23, }; float texCoords[] = { // Front face textured only, for simplicity 0.0f, 1.0f, 1.0f, 1.0f, 0.0f, 0.0f, 1.0f, 0.0f}; And it is drawn like so // Counter-clockwise winding. gl.glFrontFace(GL10.GL_CCW); // Enable face culling. gl.glEnable(GL10.GL_CULL_FACE); // What faces to remove with the face culling. gl.glCullFace(GL10.GL_BACK); // Enabled the vertices buffer for writing and to be used during // rendering. gl.glEnableClientState(GL10.GL_VERTEX_ARRAY); // Specifies the location and data format of an array of vertex // coordinates to use when rendering. gl.glVertexPointer(3, GL10.GL_FLOAT, 0, verticesBuffer); if (normalsBuffer != null) { // Enabled the normal buffer for writing and to be used during rendering. gl.glEnableClientState(GL10.GL_NORMAL_ARRAY); // Specifies the location and data format of an array of normals to use when rendering. gl.glNormalPointer(GL10.GL_FLOAT, 0, normalsBuffer); } // Set flat color gl.glColor4f(rgba[0], rgba[1], rgba[2], rgba[3]); // Smooth color if ( colorBuffer != null ) { // Enable the color array buffer to be used during rendering. gl.glEnableClientState(GL10.GL_COLOR_ARRAY); // Point out the where the color buffer is. gl.glColorPointer(4, GL10.GL_FLOAT, 0, colorBuffer); } // Use textures? if ( textureBuffer != null) { gl.glEnableClientState(GL10.GL_TEXTURE_COORD_ARRAY); gl.glEnable(GL10.GL_TEXTURE_2D); gl.glTexCoordPointer(2, GL10.GL_FLOAT, 0, textureBuffer); } // Translation and rotation before drawing gl.glTranslatef(x, y, z); gl.glRotatef(rx, 1, 0, 0); gl.glRotatef(ry, 0, 1, 0); gl.glRotatef(rz, 0, 0, 1); gl.glDrawElements(GL10.GL_TRIANGLES, numOfIndices, GL10.GL_UNSIGNED_SHORT, indicesBuffer); // Disable the vertices buffer. gl.glDisableClientState(GL10.GL_VERTEX_ARRAY); gl.glDisableClientState(GL10.GL_COLOR_ARRAY); gl.glDisableClientState(GL10.GL_NORMAL_ARRAY); gl.glDisableClientState(GL10.GL_TEXTURE_COORD_ARRAY); // Disable face culling. gl.glDisable(GL10.GL_CULL_FACE); However my front face looks like this I also add, I haven't got any normals set, are textures affected by normals? float texCoords[] = { // Front 1.0f, 1.0f, 0.0f, 1.0f, 0.0f, 0.0f, 1.0f, 0.0f} It seems as if the texture is being flipped, so the coordinates don't match up properly?

  Read the article

• NSObjectController confusion binding to a class property. Help!

  - by scottw

  Hi, I'm teaching myself cocoa and enjoying the experience most of the time. I have been struggling all day with a simple problem that google has let me down on. I have read the Cocoa Bindings Program Topics and think I grok it but still can't solve my issue. I have a very simple class called MTSong that has various properties. I have used @synthesize to create getter/setters and can use KVC to change properties. i.e in my app controller the following works: mySong = [[MTSong alloc]init]; [mySong setValue:@"2" forKey:@"version"]; In case I am doing something noddy in my class code MTSong.h is: #import <Foundation/Foundation.h> @interface MTSong : NSObject { NSNumber *version; NSString *name; } @property(readwrite, assign) NSNumber *version; @property(readwrite, assign) NSString *name; @end and MTSong.m is: #import "MTSong.h" @implementation MTSong - (id)init { [super init]; return self; } - (void)dealloc { [super dealloc]; } @synthesize version; @synthesize name; @end In Interface Builder I have a label (NSTextField) that I want to update whenever I use KVC to change the version of the song. I do the following: Drag NSObjectController object into the doc window and in the Inspector-Attributes I set: Mode: Class Class Name: MTSong Add a key called version and another called name Go to Inspector-Bindings-Controller Content Bind To: File's Owner (Not sure this is right...) Model Key Path: version Select the cell of the label and go to Inspector Bind to: Object Controller Controller Key: mySong Model Key Path: version I have attempted changing the Model Key Path in step 2 to "mySong" which makes more sense but the compiler complains. Any suggestions would be greatly appreciated. Scott Update Post Comments I wasn't exposing mySong property so have changed my AppController.h to be: #import <Cocoa/Cocoa.h> @class MTSong; @interface AppController : NSObject { IBOutlet NSButton *start; IBOutlet NSTextField *tf; MTSong *mySong; } -(IBAction)convertFile:(id)sender; @end I suspect File's owner was wrong as I am not using a document based application and I need to bind to the AppController, so step 2 is now: Go to Inspector-Bindings-Controller Content Bind To: App Controller Model Key Path: mySong I needed to change 3. to Select the cell of the label and go to Inspector Bind to: Object Controller Controller Key: selection Model Key Path: version All compiles and is playing nice!

  Read the article

• Finding the closest object in proxmity to the mouse Coordinates

  - by Cam

  Hey there, i've been working on a problem for a while now, which involves targeting the closest movieClip in relation to the x y coords of the mouse, I've attached a nice little acompanying graphic. Each mc added to the stage has it's own sub-class (HotSpots) which uses Pythag to measure distance from mouse. At this stage i can determine the closest value from my Main class but can't figure out how to reference it back to the movieclip... hope this makes sense. Below are the two Classes. My Main Class which attachs the mcs, and monitors mouse movement and traces closest value package { import flash.display.*; import flash.text.*; import flash.events.*; public class Main extends MovieClip { var pos:Number = 50; var nodeArray:Array; public function Main(){ nodeArray = []; for(var i:int = 0; i < 4; i++) { var hotSpot_mc:HotSpots = new HotSpots; hotSpot_mc.x += pos; hotSpot_mc.y += pos; addChild(hotSpot_mc); nodeArray.push(hotSpot_mc); // set some pos pos += 70; } stage.addEventListener(MouseEvent.MOUSE_MOVE,updateProxmity) } public function updateProxmity(e:MouseEvent):void { var tempArray:Array = new Array(); for(var i:int = 0; i < 4; i++) { this['tf'+[i]].text = String(nodeArray[i].dist); tempArray.push(nodeArray[i].dist); } tempArray.sort(Array.NUMERIC); var minValue:int = tempArray[0]; trace(minValue) } } } My HotSpots Class package { import flash.display.MovieClip; import flash.events.Event; import flash.text.TextField; public class HotSpots extends MovieClip { public var XSide:Number; public var YSide:Number; public var dist:Number = 0; public function HotSpots() { addEventListener(Event.ENTER_FRAME, textUp); } public function textUp(event:Event):void { XSide = this.x - MovieClip(root).mouseX; YSide = this.y - MovieClip(root).mouseY; dist = Math.round((Math.sqrt(XSide*XSide + YSide*YSide))); } } } thanks in advance

  Read the article

• Using a "white list" for extracting terms for Text Mining

  - by [email protected]

  In Part 1 of my post on "Generating cluster names from a document clustering model" (part 1, part 2, part 3), I showed how to build a clustering model from text documents using Oracle Data Miner, which automates preparing data for text mining. In this process we specified a custom stoplist and lexer and relied on Oracle Text to identify important terms.  However, there is an alternative approach, the white list, which uses a thesaurus object with the Oracle Text CTXRULE index to allow you to specify the important terms. INTRODUCTIONA stoplist is used to exclude, i.e., black list, specific words in your documents from being indexed. For example, words like a, if, and, or, and but normally add no value when text mining. Other words can also be excluded if they do not help to differentiate documents, e.g., the word Oracle is ubiquitous in the Oracle product literature. One problem with stoplists is determining which words to specify. This usually requires inspecting the terms that are extracted, manually identifying which ones you don't want, and then re-indexing the documents to determine if you missed any. Since a corpus of documents could contain thousands of words, this could be a tedious exercise. Moreover, since every word is considered as an individual token, a term excluded in one context may be needed to help identify a term in another context. For example, in our Oracle product literature example, the words "Oracle Data Mining" taken individually are not particular helpful. The term "Oracle" may be found in nearly all documents, as with the term "Data." The term "Mining" is more unique, but could also refer to the Mining industry. If we exclude "Oracle" and "Data" by specifying them in the stoplist, we lose valuable information. But it we include them, they may introduce too much noise. Still, when you have a broad vocabulary or don't have a list of specific terms of interest, you rely on the text engine to identify important terms, often by computing the term frequency - inverse document frequency metric. (This is effectively a weight associated with each term indicating its relative importance in a document within a collection of documents. We'll revisit this later.) The results using this technique is often quite valuable. As noted above, an alternative to the subtractive nature of the stoplist is to specify a white list, or a list of terms--perhaps multi-word--that we want to extract and use for data mining. The obvious downside to this approach is the need to specify the set of terms of interest. However, this may not be as daunting a task as it seems. For example, in a given domain (Oracle product literature), there is often a recognized glossary, or a list of keywords and phrases (Oracle product names, industry names, product categories, etc.). Being able to identify multi-word terms, e.g., "Oracle Data Mining" or "Customer Relationship Management" as a single token can greatly increase the quality of the data mining results. The remainder of this post and subsequent posts will focus on how to produce a dataset that contains white list terms, suitable for mining. CREATING A WHITE LIST We'll leverage the thesaurus capability of Oracle Text. Using a thesaurus, we create a set of rules that are in effect our mapping from single and multi-word terms to the tokens used to represent those terms. For example, "Oracle Data Mining" becomes "ORACLEDATAMINING." First, we'll create and populate a mapping table called my_term_token_map. All text has been converted to upper case and values in the TERM column are intended to be mapped to the token in the TOKEN column. TERM                                TOKEN DATA MINING                         DATAMINING ORACLE DATA MINING                  ORACLEDATAMINING 11G                                 ORACLE11G JAVA                                JAVA CRM                                 CRM CUSTOMER RELATIONSHIP MANAGEMENT    CRM ... Next, we'll create a thesaurus object my_thesaurus and a rules table my_thesaurus_rules: CTX_THES.CREATE_THESAURUS('my_thesaurus', FALSE); CREATE TABLE my_thesaurus_rules (main_term     VARCHAR2(100),                                  query_string  VARCHAR2(400)); We next populate the thesaurus object and rules table using the term token map. A cursor is defined over my_term_token_map. As we iterate over  the rows, we insert a synonym relationship 'SYN' into the thesaurus. We also insert into the table my_thesaurus_rules the main term, and the corresponding query string, which specifies synonyms for the token in the thesaurus. DECLARE   cursor c2 is     select token, term     from my_term_token_map; BEGIN   for r_c2 in c2 loop     CTX_THES.CREATE_RELATION('my_thesaurus',r_c2.token,'SYN',r_c2.term);     EXECUTE IMMEDIATE 'insert into my_thesaurus_rules values                        (:1,''SYN(' || r_c2.token || ', my_thesaurus)'')'     using r_c2.token;   end loop; END; We are effectively inserting the token to return and the corresponding query that will look up synonyms in our thesaurus into the my_thesaurus_rules table, for example:     'ORACLEDATAMINING'        SYN ('ORACLEDATAMINING', my_thesaurus)At this point, we create a CTXRULE index on the my_thesaurus_rules table: create index my_thesaurus_rules_idx on        my_thesaurus_rules(query_string)        indextype is ctxsys.ctxrule; In my next post, this index will be used to extract the tokens that match each of the rules specified. We'll then compute the tf-idf weights for each of the terms and create a nested table suitable for mining.

  Read the article

• SQL Server Split() Function

  - by HighAltitudeCoder

  Title goes here   Ever wanted a dbo.Split() function, but not had the time to debug it completely?  Let me guess - you are probably working on a stored procedure with 50 or more parameters; two or three of them are parameters of differing types, while the other 47 or so all of the same type (id1, id2, id3, id4, id5...).  Worse, you've found several other similar stored procedures with the ONLY DIFFERENCE being the number of like parameters taped to the end of the parameter list. If this is the situation you find yourself in now, you may be wondering, "why am I working with three different copies of what is basically the same stored procedure, and why am I having to maintain changes in three different places?  Can't I have one stored procedure that accomplishes the job of all three? My answer to you: YES!  Here is the Split() function I've created.    /******************************************************************************                                       Split.sql   ******************************************************************************/ /******************************************************************************   Split a delimited string into sub-components and return them as a table.   Parameter 1: Input string which is to be split into parts. Parameter 2: Delimiter which determines the split points in input string. Works with space or spaces as delimiter. Split() is apostrophe-safe.   SYNTAX: SELECT * FROM Split('Dvorak,Debussy,Chopin,Holst', ',') SELECT * FROM Split('Denver|Seattle|San Diego|New York', '|') SELECT * FROM Split('Denver is the super-awesomest city of them all.', ' ')   ******************************************************************************/ USE AdventureWorks GO   IF EXISTS       (SELECT *       FROM sysobjects       WHERE xtype = 'TF'       AND name = 'Split'       ) BEGIN       DROP FUNCTION Split END GO   CREATE FUNCTION Split (       @InputString                  VARCHAR(8000),       @Delimiter                    VARCHAR(50) )   RETURNS @Items TABLE (       Item                          VARCHAR(8000) )   AS BEGIN       IF @Delimiter = ' '       BEGIN             SET @Delimiter = ','             SET @InputString = REPLACE(@InputString, ' ', @Delimiter)       END         IF (@Delimiter IS NULL OR @Delimiter = '')             SET @Delimiter = ','   --INSERT INTO @Items VALUES (@Delimiter) -- Diagnostic --INSERT INTO @Items VALUES (@InputString) -- Diagnostic         DECLARE @Item                 VARCHAR(8000)       DECLARE @ItemList       VARCHAR(8000)       DECLARE @DelimIndex     INT         SET @ItemList = @InputString       SET @DelimIndex = CHARINDEX(@Delimiter, @ItemList, 0)       WHILE (@DelimIndex != 0)       BEGIN             SET @Item = SUBSTRING(@ItemList, 0, @DelimIndex)             INSERT INTO @Items VALUES (@Item)               -- Set @ItemList = @ItemList minus one less item             SET @ItemList = SUBSTRING(@ItemList, @DelimIndex+1, LEN(@ItemList)-@DelimIndex)             SET @DelimIndex = CHARINDEX(@Delimiter, @ItemList, 0)       END -- End WHILE         IF @Item IS NOT NULL -- At least one delimiter was encountered in @InputString       BEGIN             SET @Item = @ItemList             INSERT INTO @Items VALUES (@Item)       END         -- No delimiters were encountered in @InputString, so just return @InputString       ELSE INSERT INTO @Items VALUES (@InputString)         RETURN   END -- End Function GO   ---- Set Permissions --GRANT SELECT ON Split TO UserRole1 --GRANT SELECT ON Split TO UserRole2 --GO   The syntax is basically as follows: SELECT <fields> FROM Table 1 JOIN Table 2 ON ... JOIN Table 3 ON ... WHERE LOGICAL CONDITION A AND LOGICAL CONDITION B AND LOGICAL CONDITION C AND TABLE2.Id IN (SELECT * FROM Split(@IdList, ',')) @IdList is a parameter passed into the stored procedure, and the comma (',') is the delimiter you have chosen to split the parameter list on. You can also use it like this: SELECT <fields> FROM Table 1 JOIN Table 2 ON ... JOIN Table 3 ON ... WHERE LOGICAL CONDITION A AND LOGICAL CONDITION B AND LOGICAL CONDITION C HAVING COUNT(SELECT * FROM Split(@IdList, ',') Similarly, it can be used in other aggregate functions at run-time: SELECT MIN(SELECT * FROM Split(@IdList, ','), <fields> FROM Table 1 JOIN Table 2 ON ... JOIN Table 3 ON ... WHERE LOGICAL CONDITION A AND LOGICAL CONDITION B AND LOGICAL CONDITION C GROUP BY <fields> Now that I've (hopefully effectively) explained the benefits to using this function and implementing it in one or more of your database objects, let me warn you of a caveat that you are likely to encounter.  You may have a team member who waits until the right moment to ask you a pointed question: "Doesn't this function just do the same thing as using the IN function?  Why didn't you just use that instead?  In other words, why bother with this function?" What's happening is, one or more team members has failed to understand the reason for implementing this kind of function in the first place.  (Note: this is THE MOST IMPORTANT ASPECT OF THIS POST). Allow me to outline a few pros to implementing this function, so you may effectively parry this question.  Touche. 1) Code consolidation.  You don't have to maintain what is basically the same code and logic, but with varying numbers of the same parameter in several SQL objects.  I'm not going to go into the cons related to using this function, because the afore mentioned team member is probably more than adept at pointing these out.  Remember, the real positive contribution is ou are decreasing the liklihood that your team fails to update all (x) duplicate copies of what are basically the same stored procedure, and so on...  This is the classic downside to duplicate code.  It is a virus, and you should kill it. You might be better off rejecting your team member's question, and responding with your own: "Would you rather maintain the same logic in multiple different stored procedures, and hope that the team doesn't forget to always update all of them at the same time?".  In his head, he might be thinking "yes, I would like to maintain several different copies of the same stored procedure", although you probably will not get such a direct response.  2) Added flexibility - you can use the Split function elsewhere, and for splitting your data in different ways.  Plus, you can use any kind of delimiter you wish.  How can you know today the ways in which you might want to examine your data tomorrow?  Segue to my next point. 3) Because the function takes a delimiter parameter, you can split the data in any number of ways.  This greatly increases the utility of such a function and enables your team to work with the data in a variety of different ways in the future.  You can split on a single char, symbol, word, or group of words.  You can split on spaces.  (The list goes on... test it out). Finally, you can dynamically define the behavior of a stored procedure (or other SQL object) at run time, through the use of this function.  Rather than have several objects that accomplish almost the same thing, why not have only one instead?

  Read the article

• Solaris X86 64-bit Assembly Programming

  - by danx

  Solaris X86 64-bit Assembly Programming This is a simple example on writing, compiling, and debugging Solaris 64-bit x86 assembly language with a C program. This is also referred to as "AMD64" assembly. The term "AMD64" is used in an inclusive sense to refer to all X86 64-bit processors, whether AMD Opteron family or Intel 64 processor family. Both run Solaris x86. I'm keeping this example simple mainly to illustrate how everything comes together—compiler, assembler, linker, and debugger when using assembly language. The example I'm using here is a C program that calls an assembly language program passing a C string. The assembly language program takes the C string and calls printf() with it to print the string. AMD64 Register Usage But first let's review the use of AMD64 registers. AMD64 has several 64-bit registers, some special purpose (such as the stack pointer) and others general purpose. By convention, Solaris follows the AMD64 ABI in register usage, which is the same used by Linux, but different from Microsoft Windows in usage (such as which registers are used to pass parameters). This blog will only discuss conventions for Linux and Solaris. The following chart shows how AMD64 registers are used. The first six parameters to a function are passed through registers. If there's more than six parameters, parameter 7 and above are pushed on the stack before calling the function. The stack is also used to save temporary "stack" variables for use by a function. 64-bit Register Usage %rip Instruction Pointer points to the current instruction %rsp Stack Pointer %rbp Frame Pointer (saved stack pointer pointing to parameters on stack) %rdi Function Parameter 1 %rsi Function Parameter 2 %rdx Function Parameter 3 %rcx Function Parameter 4 %r8 Function Parameter 5 %r9 Function Parameter 6 %rax Function return value %r10, %r11 Temporary registers (need not be saved before used) %rbx, %r12, %r13, %r14, %r15 Temporary registers, but must be saved before use and restored before returning from the current function (usually with the push and pop instructions). 32-, 16-, and 8-bit registers To access the lower 32-, 16-, or 8-bits of a 64-bit register use the following: 64-bit register Least significant 32-bits Least significant 16-bits Least significant 8-bits %rax%eax%ax%al %rbx%ebx%bx%bl %rcx%ecx%cx%cl %rdx%edx%dx%dl %rsi%esi%si%sil %rdi%edi%di%axl %rbp%ebp%bp%bp %rsp%esp%sp%spl %r9%r9d%r9w%r9b %r10%r10d%r10w%r10b %r11%r11d%r11w%r11b %r12%r12d%r12w%r12b %r13%r13d%r13w%r13b %r14%r14d%r14w%r14b %r15%r15d%r15w%r15b %r16%r16d%r16w%r16b There's other registers present, such as the 64-bit %mm registers, 128-bit %xmm registers, 256-bit %ymm registers, and 512-bit %zmm registers. Except for %mm registers, these registers may not present on older AMD64 processors. Assembly Source The following is the source for a C program, helloas1.c, that calls an assembly function, hello_asm(). $ cat helloas1.c extern void hello_asm(char *s); int main(void) { hello_asm("Hello, World!"); } The assembly function called above, hello_asm(), is defined below. $ cat helloas2.s /* * helloas2.s * To build: * cc -m64 -o helloas2-cpp.s -D_ASM -E helloas2.s * cc -m64 -c -o helloas2.o helloas2-cpp.s */ #if defined(lint) || defined(__lint) /* ARGSUSED */ void hello_asm(char *s) { } #else /* lint */ #include <sys/asm_linkage.h> .extern printf ENTRY_NP(hello_asm) // Setup printf parameters on stack mov %rdi, %rsi // P2 (%rsi) is string variable lea .printf_string, %rdi // P1 (%rdi) is printf format string call printf ret SET_SIZE(hello_asm) // Read-only data .text .align 16 .type .printf_string, @object .printf_string: .ascii "The string is: %s.\n\0" #endif /* lint || __lint */ In the assembly source above, the C skeleton code under "#if defined(lint)" is optionally used for lint to check the interfaces with your C program--very useful to catch nasty interface bugs. The "asm_linkage.h" file includes some handy macros useful for assembly, such as ENTRY_NP(), used to define a program entry point, and SET_SIZE(), used to set the function size in the symbol table. The function hello_asm calls C function printf() by passing two parameters, Parameter 1 (P1) is a printf format string, and P2 is a string variable. The function begins by moving %rdi, which contains Parameter 1 (P1) passed hello_asm, to printf()'s P2, %rsi. Then it sets printf's P1, the format string, by loading the address the address of the format string in %rdi, P1. Finally it calls printf. After returning from printf, the hello_asm function returns itself. Larger, more complex assembly functions usually do more setup than the example above. If a function is returning a value, it would set %rax to the return value. Also, it's typical for a function to save the %rbp and %rsp registers of the calling function and to restore these registers before returning. %rsp contains the stack pointer and %rbp contains the frame pointer. Here is the typical function setup and return sequence for a function: ENTRY_NP(sample_assembly_function) push %rbp // save frame pointer on stack mov %rsp, %rbp // save stack pointer in frame pointer xor %rax, %r4ax // set function return value to 0. mov %rbp, %rsp // restore stack pointer pop %rbp // restore frame pointer ret // return to calling function SET_SIZE(sample_assembly_function) Compiling and Running Assembly Use the Solaris cc command to compile both C and assembly source, and to pre-process assembly source. You can also use GNU gcc instead of cc to compile, if you prefer. The "-m64" option tells the compiler to compile in 64-bit address mode (instead of 32-bit). $ cc -m64 -o helloas2-cpp.s -D_ASM -E helloas2.s $ cc -m64 -c -o helloas2.o helloas2-cpp.s $ cc -m64 -c helloas1.c $ cc -m64 -o hello-asm helloas1.o helloas2.o $ file hello-asm helloas1.o helloas2.o hello-asm: ELF 64-bit LSB executable AMD64 Version 1 [SSE FXSR FPU], dynamically linked, not stripped helloas1.o: ELF 64-bit LSB relocatable AMD64 Version 1 helloas2.o: ELF 64-bit LSB relocatable AMD64 Version 1 $ hello-asm The string is: Hello, World!. Debugging Assembly with MDB MDB is the Solaris system debugger. It can also be used to debug user programs, including assembly and C. The following example runs the above program, hello-asm, under control of the debugger. In the example below I load the program, set a breakpoint at the assembly function hello_asm, display the registers and the first parameter, step through the assembly function, and continue execution. $ mdb hello-asm # Start the debugger > hello_asm:b # Set a breakpoint > ::run # Run the program under the debugger mdb: stop at hello_asm mdb: target stopped at: hello_asm: movq %rdi,%rsi > $C # display function stack ffff80ffbffff6e0 hello_asm() ffff80ffbffff6f0 0x400adc() > $r # display registers %rax = 0x0000000000000000 %r8 = 0x0000000000000000 %rbx = 0xffff80ffbf7f8e70 %r9 = 0x0000000000000000 %rcx = 0x0000000000000000 %r10 = 0x0000000000000000 %rdx = 0xffff80ffbffff718 %r11 = 0xffff80ffbf537db8 %rsi = 0xffff80ffbffff708 %r12 = 0x0000000000000000 %rdi = 0x0000000000400cf8 %r13 = 0x0000000000000000 %r14 = 0x0000000000000000 %r15 = 0x0000000000000000 %cs = 0x0053 %fs = 0x0000 %gs = 0x0000 %ds = 0x0000 %es = 0x0000 %ss = 0x004b %rip = 0x0000000000400c70 hello_asm %rbp = 0xffff80ffbffff6e0 %rsp = 0xffff80ffbffff6c8 %rflags = 0x00000282 id=0 vip=0 vif=0 ac=0 vm=0 rf=0 nt=0 iopl=0x0 status=<of,df,IF,tf,SF,zf,af,pf,cf> %gsbase = 0x0000000000000000 %fsbase = 0xffff80ffbf782a40 %trapno = 0x3 %err = 0x0 > ::dis # disassemble the current instructions hello_asm: movq %rdi,%rsi hello_asm+3: leaq 0x400c90,%rdi hello_asm+0xb: call -0x220 <PLT:printf> hello_asm+0x10: ret 0x400c81: nop 0x400c85: nop 0x400c88: nop 0x400c8c: nop 0x400c90: pushq %rsp 0x400c91: pushq $0x74732065 0x400c96: jb +0x69 <0x400d01> > 0x0000000000400cf8/S # %rdi contains Parameter 1 0x400cf8: Hello, World! > [ # Step and execute 1 instruction mdb: target stopped at: hello_asm+3: leaq 0x400c90,%rdi > [ mdb: target stopped at: hello_asm+0xb: call -0x220 <PLT:printf> > [ The string is: Hello, World!. mdb: target stopped at: hello_asm+0x10: ret > [ mdb: target stopped at: main+0x19: movl $0x0,-0x4(%rbp) > :c # continue program execution mdb: target has terminated > $q # quit the MDB debugger $ In the example above, at the start of function hello_asm(), I display the stack contents with "$C", display the registers contents with "$r", then disassemble the current function with "::dis". The first function parameter, which is a C string, is passed by reference with the string address in %rdi (see the register usage chart above). The address is 0x400cf8, so I print the value of the string with the "/S" MDB command: "0x0000000000400cf8/S". I can also print the contents at an address in several other formats. Here's a few popular formats. For more, see the mdb(1) man page for details. address/S C string address/C ASCII character (1 byte) address/E unsigned decimal (8 bytes) address/U unsigned decimal (4 bytes) address/D signed decimal (4 bytes) address/J hexadecimal (8 bytes) address/X hexadecimal (4 bytes) address/B hexadecimal (1 bytes) address/K pointer in hexadecimal (4 or 8 bytes) address/I disassembled instruction Finally, I step through each machine instruction with the "[" command, which steps over functions. If I wanted to enter a function, I would use the "]" command. Then I continue program execution with ":c", which continues until the program terminates. MDB Basic Cheat Sheet Here's a brief cheat sheet of some of the more common MDB commands useful for assembly debugging. There's an entire set of macros and more powerful commands, especially some for debugging the Solaris kernel, but that's beyond the scope of this example. $C Display function stack with pointers $c Display function stack $e Display external function names $v Display non-zero variables and registers $r Display registers ::fpregs Display floating point (or "media" registers). Includes %st, %xmm, and %ymm registers. ::status Display program status ::run Run the program (followed by optional command line parameters) $q Quit the debugger address:b Set a breakpoint address:d Delete a breakpoint $b Display breakpoints :c Continue program execution after a breakpoint [ Step 1 instruction, but step over function calls ] Step 1 instruction address::dis Disassemble instructions at an address ::events Display events Further Information "Assembly Language Techniques for Oracle Solaris on x86 Platforms" by Paul Lowik (2004). Good tutorial on Solaris x86 optimization with assembly. The Solaris Operating System on x86 Platforms An excellent, detailed tutorial on X86 architecture, with Solaris specifics. By an ex-Sun employee, Frank Hofmann (2005). "AMD64 ABI Features", Solaris 64-bit Developer's Guide contains rules on data types and register usage for Intel 64/AMD64-class processors. (available at docs.oracle.com) Solaris X86 Assembly Language Reference Manual (available at docs.oracle.com) SPARC Assembly Language Reference Manual (available at docs.oracle.com) System V Application Binary Interface (2003) defines the AMD64 ABI for UNIX-class operating systems, including Solaris, Linux, and BSD. Google for it—the original website is gone. cc(1), gcc(1), and mdb(1) man pages.

  Read the article

• I'm looking for a reliable way to verify T-SQL stored procedures. Anybody got one?

  - by Cory Larson

  Hi all-- We're upgrading from SQL Server 2005 to 2008. Almost every database in the 2005 instance is set to 2000 compatibility mode, but we're jumping to 2008. Our testing is complete, but what we've learned is that we need to get faster at it. I've discovered some stored procedures that either SELECT data from missing tables or try to ORDER BY columns that don't exist. Wrapping the SQL to create the procedures in SET PARSEONLY ON and trapping errors in a try/catch only catches the invalid columns in the ORDER BYs. It does not find the error with the procedure selecting data from the missing table. SSMS 2008's intellisense, however, DOES find the issue, but I can still go ahead and successfully run the ALTER script for the procedure without it complaining. So, why can I even get away with creating a procedure that fails when it runs? Are there any tools out there that can do better than what I've tried? The first tool I found wasn't very useful: DbValidator from CodeProject, but it finds fewer problems than this script I found on SqlServerCentral, which found the invalid column references. ------------------------------------------------------------------------- -- Check Syntax of Database Objects -- Copyrighted work. Free to use as a tool to check your own code or in -- any software not sold. All other uses require written permission. ------------------------------------------------------------------------- -- Turn on ParseOnly so that we don't actually execute anything. SET PARSEONLY ON GO -- Create a table to iterate through declare @ObjectList table (ID_NUM int NOT NULL IDENTITY (1, 1), OBJ_NAME varchar(255), OBJ_TYPE char(2)) -- Get a list of most of the scriptable objects in the DB. insert into @ObjectList (OBJ_NAME, OBJ_TYPE) SELECT name, type FROM sysobjects WHERE type in ('P', 'FN', 'IF', 'TF', 'TR', 'V') order by type, name -- Var to hold the SQL that we will be syntax checking declare @SQLToCheckSyntaxFor varchar(max) -- Var to hold the name of the object we are currently checking declare @ObjectName varchar(255) -- Var to hold the type of the object we are currently checking declare @ObjectType char(2) -- Var to indicate our current location in iterating through the list of objects declare @IDNum int -- Var to indicate the max number of objects we need to iterate through declare @MaxIDNum int -- Set the inital value and max value select @IDNum = Min(ID_NUM), @MaxIDNum = Max(ID_NUM) from @ObjectList -- Begin iteration while @IDNum <= @MaxIDNum begin -- Load per iteration values here select @ObjectName = OBJ_NAME, @ObjectType = OBJ_TYPE from @ObjectList where ID_NUM = @IDNum -- Get the text of the db Object (ie create script for the sproc) SELECT @SQLToCheckSyntaxFor = OBJECT_DEFINITION(OBJECT_ID(@ObjectName, @ObjectType)) begin try -- Run the create script (remember that PARSEONLY has been turned on) EXECUTE(@SQLToCheckSyntaxFor) end try begin catch -- See if the object name is the same in the script and the catalog (kind of a special error) if (ERROR_PROCEDURE() <> @ObjectName) begin print 'Error in ' + @ObjectName print ' The Name in the script is ' + ERROR_PROCEDURE()+ '. (They don''t match)' end -- If the error is just that this already exists then we don't want to report that. else if (ERROR_MESSAGE() <> 'There is already an object named ''' + ERROR_PROCEDURE() + ''' in the database.') begin -- Report the error that we got. print 'Error in ' + ERROR_PROCEDURE() print ' ERROR TEXT: ' + ERROR_MESSAGE() end end catch -- Setup to iterate to the next item in the table select @IDNum = case when Min(ID_NUM) is NULL then @IDNum + 1 else Min(ID_NUM) end from @ObjectList where ID_NUM > @IDNum end -- Turn the ParseOnly back off. SET PARSEONLY OFF GO Any suggestions?

  Read the article

• Getting text position while parsing pdf with Quartz 2D

  - by Koteg

  Hi guys, another question regarding pdf parsing... Just read PDF Reference version 1.7 "5.3.1 Text-Positioning Operators" and I am a little bit confused. I wrote some code to get transformation matrix and initial text position. CGPDFOperatorTableSetCallback (table, "MP", &op_MP);//Define marked-content point CGPDFOperatorTableSetCallback (table, "DP", &op_DP);//Define marked-content point with property list CGPDFOperatorTableSetCallback (table, "BMC", &op_BMC);//Begin marked-content sequence CGPDFOperatorTableSetCallback (table, "BDC", &op_BDC);//Begin marked-content sequence with property list CGPDFOperatorTableSetCallback (table, "EMC", &op_EMC);//End marked-content sequence //Text State operators CGPDFOperatorTableSetCallback(table, "Tc", &op_Tc); CGPDFOperatorTableSetCallback(table, "Tw", &op_Tw); CGPDFOperatorTableSetCallback(table, "Tz", &op_Tz); CGPDFOperatorTableSetCallback(table, "TL", &op_TL); CGPDFOperatorTableSetCallback(table, "Tf", &op_Tf); CGPDFOperatorTableSetCallback(table, "Tr", &op_Tr); CGPDFOperatorTableSetCallback(table, "Ts", &op_Ts); //text showing operators CGPDFOperatorTableSetCallback(table, "TJ", &op_TJ); CGPDFOperatorTableSetCallback(table, "Tj", &op_Tj); CGPDFOperatorTableSetCallback(table, "'", &op_apostrof); CGPDFOperatorTableSetCallback(table, "\"", &op_double_apostrof); //text positioning operators CGPDFOperatorTableSetCallback(table, "Td", &op_Td); CGPDFOperatorTableSetCallback(table, "TD", &op_TD); CGPDFOperatorTableSetCallback(table, "Tm", &op_Tm); CGPDFOperatorTableSetCallback(table, "T*", &op_T); //text object operators CGPDFOperatorTableSetCallback(table, "BT", &op_BT);//Begin text object CGPDFOperatorTableSetCallback(table, "ET", &op_ET);//End text object So this is the output after application lunch: 2010-09-02 15:09:23.041 testSearch[8251:207] op_BT begin Integer value: 0 2010-09-02 15:09:23.043 testSearch[8251:207] op_BT end 2010-09-02 15:09:23.043 testSearch[8251:207] op_Tf begin Integer value: 1 2010-09-02 15:09:23.044 testSearch[8251:207] op_Tf end 2010-09-02 15:09:23.044 testSearch[8251:207] op_Tm begin Float value: 557.364197 2010-09-02 15:09:23.045 testSearch[8251:207] op_Tm end 2010-09-02 15:09:23.045 testSearch[8251:207] op_TJ begin 2010-09-02 15:09:23.046 testSearch[8251:207] Array string value [0]: F 2010-09-02 15:09:23.046 testSearch[8251:207] Array integer value [1]: 94985208 2010-09-02 15:09:23.047 testSearch[8251:207] Array string value [2]: r 2010-09-02 15:09:23.047 testSearch[8251:207] Array integer value [3]: 94985208 2010-09-02 15:09:23.048 testSearch[8251:207] Array string value [4]: o 2010-09-02 15:09:23.048 testSearch[8251:207] Array integer value [5]: 94985208 2010-09-02 15:09:23.049 testSearch[8251:207] Array string value [6]: m s 2010-09-02 15:09:23.049 testSearch[8251:207] Array integer value [7]: 94985208 2010-09-02 15:09:23.049 testSearch[8251:207] Array string value [8]: a 2010-09-02 15:09:23.050 testSearch[8251:207] Array integer value [9]: 94985208 2010-09-02 15:09:23.050 testSearch[8251:207] Array string value [10]: m 2010-09-02 15:09:23.051 testSearch[8251:207] Array integer value [11]: 94985208 2010-09-02 15:09:23.051 testSearch[8251:207] Array string value [12]: p 2010-09-02 15:09:23.052 testSearch[8251:207] Array integer value [13]: 94985208 2010-09-02 15:09:23.053 testSearch[8251:207] Array string value [14]: l 2010-09-02 15:09:23.054 testSearch[8251:207] Array integer value [15]: 94985208 2010-09-02 15:09:23.055 testSearch[8251:207] Array string value [16]: e t 2010-09-02 15:09:23.055 testSearch[8251:207] Array integer value [17]: 94985208 2010-09-02 15:09:23.057 testSearch[8251:207] Array string value [18]: o r 2010-09-02 15:09:23.057 testSearch[8251:207] Array integer value [19]: 94985208 2010-09-02 15:09:23.058 testSearch[8251:207] Array string value [20]: e 2010-09-02 15:09:23.058 testSearch[8251:207] Array integer value [21]: 94985208 2010-09-02 15:09:23.059 testSearch[8251:207] Array string value [22]: s 2010-09-02 15:09:23.059 testSearch[8251:207] Array integer value [23]: 94985208 2010-09-02 15:09:23.060 testSearch[8251:207] Array string value [24]: u 2010-09-02 15:09:23.061 testSearch[8251:207] Array integer value [25]: 94985208 2010-09-02 15:09:23.061 testSearch[8251:207] Array string value [26]: l 2010-09-02 15:09:23.062 testSearch[8251:207] Array integer value [27]: 94985208 2010-09-02 15:09:23.062 testSearch[8251:207] Array string value [28]: t 2010-09-02 15:09:23.063 testSearch[8251:207] op_TJ end If someone is familiar with text matrix and text positioning operators it would be nice to explain how all those thing work. How to calculate text position (or glyph?) using Tm (transformation matrix and other data)?

  Read the article

• Form contents not showing in email

  - by fmz

  This is a followup to a question I posted yesterday. I thought everything was working fine, but today, I am not getting any results in the email from the drop down field. Here is the form code in question: <label for="purpose"><span class="required">*</span> Purpose</label> <select id="purpose" name="purpose" style="width: 300px; height:35px;"> <option value="" selected="selected">-- Select One --</option> <option value="I am interested in your services">I am interested in your services!</option> <option value="I am interested in a partnership">I am interested in a partnership!</option> <option value="I am interested in a job">I am interested in a job!</option> </select> It is then processed in PHP and should output the selected option to an email, however the Reason for Contact line always comes through with nothing in it. Here is the PHP code: <?php if(!$_POST) exit; $name = $_POST['name']; $company = $_POST['company']; $email = $_POST['email']; $phone = $_POST['phone']; $purpose = $_POST['purpose']; $comments = $_POST['comments']; $verify = $_POST['verify']; if(trim($name) == '') { echo '<div class="error_message">Attention! You must enter your name.</div>'; exit(); } else if(trim($email) == '') { echo '<div class="error_message">Attention! Please enter a valid email address.</div>'; exit(); } else if(trim($phone) == '') { echo '<div class="error_message">Attention! Please enter a valid phone number.</div>'; exit(); } else if(!isEmail($email)) { echo '<div class="error_message">Attention! You have enter an invalid e-mail address, try again.</div>'; exit(); } if(trim($comments) == '') { echo '<div class="error_message">Attention! Please enter your message.</div>'; exit(); } else if(trim($verify) == '') { echo '<div class="error_message">Attention! Please enter the verification number.</div>'; exit(); } else if(trim($verify) != '4') { echo '<div class="error_message">Attention! The verification number you entered is incorrect.</div>'; exit(); } if($error == '') { if(get_magic_quotes_gpc()) { $comments = stripslashes($comments); } // Configuration option. // Enter the email address that you want to emails to be sent to. // Example $address = "[email protected]"; $address = "[email protected]"; // Configuration option. // i.e. The standard subject will appear as, "You've been contacted by John Doe." // Example, $e_subject = '$name . ' has contacted you via Your Website.'; $e_subject = 'You\'ve been contacted by ' . $name . '.'; // Configuration option. // You can change this if you feel that you need to. // Developers, you may wish to add more fields to the form, in which case you must be sure to add them here. $e_body = "You have been contacted by $name.\r\n\n"; $e_company = "Company: $company\r\n\n"; $e_content = "Comments: \"$comments\"\r\n\n"; $e_purpose = "Reason for contact: $purpose\r\n\n"; $e_reply = "You can contact $name via email, $email or via phone $phone"; $msg = $e_body . $e_content . $e_company . $e_purpose . $e_reply; if(mail($address, $e_subject, $msg, "From: $email\r\nReply-To: $email\r\nReturn-Path: $email\r\n")) { // Email has sent successfully, echo a success page. echo "<fieldset>"; echo "<div id='success_page'>"; echo "<h1>Email Sent Successfully.</h1>"; echo "<p>Thank you <strong>$name</strong>, your message has been submitted to us.</p>"; echo "</div>"; echo "</fieldset>"; } else { echo 'ERROR!'; } } function isEmail($email) { // Email address verification, do not edit. return(preg_match("/^[-_.[:alnum:]]+@((([[:alnum:]]|[[:alnum:]][[:alnum:]-]*[[:alnum:]])\.)+(ad|ae|aero|af|ag|ai|al|am|an|ao|aq|ar|arpa|as|at|au|aw|az|ba|bb|bd|be|bf|bg|bh|bi|biz|bj|bm|bn|bo|br|bs|bt|bv|bw|by|bz|ca|cc|cd|cf|cg|ch|ci|ck|cl|cm|cn|co|com|coop|cr|cs|cu|cv|cx|cy|cz|de|dj|dk|dm|do|dz|ec|edu|ee|eg|eh|er|es|et|eu|fi|fj|fk|fm|fo|fr|ga|gb|gd|ge|gf|gh|gi|gl|gm|gn|gov|gp|gq|gr|gs|gt|gu|gw|gy|hk|hm|hn|hr|ht|hu|id|ie|il|in|info|int|io|iq|ir|is|it|jm|jo|jp|ke|kg|kh|ki|km|kn|kp|kr|kw|ky|kz|la|lb|lc|li|lk|lr|ls|lt|lu|lv|ly|ma|mc|md|mg|mh|mil|mk|ml|mm|mn|mo|mp|mq|mr|ms|mt|mu|museum|mv|mw|mx|my|mz|na|name|nc|ne|net|nf|ng|ni|nl|no|np|nr|nt|nu|nz|om|org|pa|pe|pf|pg|ph|pk|pl|pm|pn|pr|pro|ps|pt|pw|py|qa|re|ro|ru|rw|sa|sb|sc|sd|se|sg|sh|si|sj|sk|sl|sm|sn|so|sr|st|su|sv|sy|sz|tc|td|tf|tg|th|tj|tk|tm|tn|to|tp|tr|tt|tv|tw|tz|ua|ug|uk|um|us|uy|uz|va|vc|ve|vg|vi|vn|vu|wf|ws|ye|yt|yu|za|zm|zw)$|(([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5])\.){3}([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5]))$/i",$email)); } ?> Any assistance would be greatly appreciated. Thanks!

  Read the article

• How to use onSensorChanged sensor data in combination with OpenGL

  - by Sponge

  I have written a TestSuite to find out how to calculate the rotation angles from the data you get in SensorEventListener.onSensorChanged(). I really hope you can complete my solution to help people who will have the same problems like me. Here is the code, i think you will understand it after reading it. Feel free to change it, the main idea was to implement several methods to send the orientation angles to the opengl view or any other target which would need it. method 1 to 4 are working, they are directly sending the rotationMatrix to the OpenGl view. all other methods are not working or buggy and i hope someone knows to get them working. i think the best method would be method 5 if it would work, because it would be the easiest to understand but i'm not sure how efficient it is. the complete code isn't optimized so i recommend to not use it as it is in your project. here it is: import java.nio.ByteBuffer; import java.nio.ByteOrder; import java.nio.FloatBuffer; import javax.microedition.khronos.egl.EGL10; import javax.microedition.khronos.egl.EGLConfig; import javax.microedition.khronos.opengles.GL10; import static javax.microedition.khronos.opengles.GL10.*; import android.app.Activity; import android.content.Context; import android.content.pm.ActivityInfo; import android.hardware.Sensor; import android.hardware.SensorEvent; import android.hardware.SensorEventListener; import android.hardware.SensorManager; import android.opengl.GLSurfaceView; import android.opengl.GLSurfaceView.Renderer; import android.os.Bundle; import android.util.Log; import android.view.WindowManager; /** * This class provides a basic demonstration of how to use the * {@link android.hardware.SensorManager SensorManager} API to draw a 3D * compass. */ public class SensorToOpenGlTests extends Activity implements Renderer, SensorEventListener { private static final boolean TRY_TRANSPOSED_VERSION = false; /* * MODUS overview: * * 1 - unbufferd data directly transfaired from the rotation matrix to the * modelview matrix * * 2 - buffered version of 1 where both acceleration and magnetometer are * buffered * * 3 - buffered version of 1 where only magnetometer is buffered * * 4 - buffered version of 1 where only acceleration is buffered * * 5 - uses the orientation sensor and sets the angles how to rotate the * camera with glrotate() * * 6 - uses the rotation matrix to calculate the angles * * 7 to 12 - every possibility how the rotationMatrix could be constructed * in SensorManager.getRotationMatrix (see * http://www.songho.ca/opengl/gl_anglestoaxes.html#anglestoaxes for all * possibilities) */ private static int MODUS = 2; private GLSurfaceView openglView; private FloatBuffer vertexBuffer; private ByteBuffer indexBuffer; private FloatBuffer colorBuffer; private SensorManager mSensorManager; private float[] rotationMatrix = new float[16]; private float[] accelGData = new float[3]; private float[] bufferedAccelGData = new float[3]; private float[] magnetData = new float[3]; private float[] bufferedMagnetData = new float[3]; private float[] orientationData = new float[3]; // private float[] mI = new float[16]; private float[] resultingAngles = new float[3]; private int mCount; final static float rad2deg = (float) (180.0f / Math.PI); private boolean mirrorOnBlueAxis = false; private boolean landscape; public SensorToOpenGlTests() { } /** Called with the activity is first created. */ @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); mSensorManager = (SensorManager) getSystemService(Context.SENSOR_SERVICE); openglView = new GLSurfaceView(this); openglView.setRenderer(this); setContentView(openglView); } @Override protected void onResume() { // Ideally a game should implement onResume() and onPause() // to take appropriate action when the activity looses focus super.onResume(); openglView.onResume(); if (((WindowManager) getSystemService(WINDOW_SERVICE)) .getDefaultDisplay().getOrientation() == 1) { landscape = true; } else { landscape = false; } mSensorManager.registerListener(this, mSensorManager .getDefaultSensor(Sensor.TYPE_ACCELEROMETER), SensorManager.SENSOR_DELAY_GAME); mSensorManager.registerListener(this, mSensorManager .getDefaultSensor(Sensor.TYPE_MAGNETIC_FIELD), SensorManager.SENSOR_DELAY_GAME); mSensorManager.registerListener(this, mSensorManager .getDefaultSensor(Sensor.TYPE_ORIENTATION), SensorManager.SENSOR_DELAY_GAME); } @Override protected void onPause() { // Ideally a game should implement onResume() and onPause() // to take appropriate action when the activity looses focus super.onPause(); openglView.onPause(); mSensorManager.unregisterListener(this); } public int[] getConfigSpec() { // We want a depth buffer, don't care about the // details of the color buffer. int[] configSpec = { EGL10.EGL_DEPTH_SIZE, 16, EGL10.EGL_NONE }; return configSpec; } public void onDrawFrame(GL10 gl) { // clear screen and color buffer: gl.glClear(GL10.GL_COLOR_BUFFER_BIT | GL10.GL_DEPTH_BUFFER_BIT); // set target matrix to modelview matrix: gl.glMatrixMode(GL10.GL_MODELVIEW); // init modelview matrix: gl.glLoadIdentity(); // move camera away a little bit: if ((MODUS == 1) || (MODUS == 2) || (MODUS == 3) || (MODUS == 4)) { if (landscape) { // in landscape mode first remap the rotationMatrix before using // it with glMultMatrixf: float[] result = new float[16]; SensorManager.remapCoordinateSystem(rotationMatrix, SensorManager.AXIS_Y, SensorManager.AXIS_MINUS_X, result); gl.glMultMatrixf(result, 0); } else { gl.glMultMatrixf(rotationMatrix, 0); } } else { //in all other modes do the rotation by hand: gl.glRotatef(resultingAngles[1], 1, 0, 0); gl.glRotatef(resultingAngles[2], 0, 1, 0); gl.glRotatef(resultingAngles[0], 0, 0, 1); if (mirrorOnBlueAxis) { //this is needed for mode 6 to work gl.glScalef(1, 1, -1); } } //move the axis to simulate augmented behaviour: gl.glTranslatef(0, 2, 0); // draw the 3 axis on the screen: gl.glVertexPointer(3, GL_FLOAT, 0, vertexBuffer); gl.glColorPointer(4, GL_FLOAT, 0, colorBuffer); gl.glDrawElements(GL_LINES, 6, GL_UNSIGNED_BYTE, indexBuffer); } public void onSurfaceChanged(GL10 gl, int width, int height) { gl.glViewport(0, 0, width, height); float r = (float) width / height; gl.glMatrixMode(GL10.GL_PROJECTION); gl.glLoadIdentity(); gl.glFrustumf(-r, r, -1, 1, 1, 10); } public void onSurfaceCreated(GL10 gl, EGLConfig config) { gl.glDisable(GL10.GL_DITHER); gl.glClearColor(1, 1, 1, 1); gl.glEnable(GL10.GL_CULL_FACE); gl.glShadeModel(GL10.GL_SMOOTH); gl.glEnable(GL10.GL_DEPTH_TEST); gl.glEnableClientState(GL10.GL_VERTEX_ARRAY); gl.glEnableClientState(GL10.GL_COLOR_ARRAY); // load the 3 axis and there colors: float vertices[] = { 0, 0, 0, 1, 0, 0, 0, 1, 0, 0, 0, 1 }; float colors[] = { 0, 0, 0, 0, 1, 0, 0, 1, 0, 1, 0, 1, 0, 0, 1, 1 }; byte indices[] = { 0, 1, 0, 2, 0, 3 }; ByteBuffer vbb; vbb = ByteBuffer.allocateDirect(vertices.length * 4); vbb.order(ByteOrder.nativeOrder()); vertexBuffer = vbb.asFloatBuffer(); vertexBuffer.put(vertices); vertexBuffer.position(0); vbb = ByteBuffer.allocateDirect(colors.length * 4); vbb.order(ByteOrder.nativeOrder()); colorBuffer = vbb.asFloatBuffer(); colorBuffer.put(colors); colorBuffer.position(0); indexBuffer = ByteBuffer.allocateDirect(indices.length); indexBuffer.put(indices); indexBuffer.position(0); } public void onAccuracyChanged(Sensor sensor, int accuracy) { } public void onSensorChanged(SensorEvent event) { // load the new values: loadNewSensorData(event); if (MODUS == 1) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); } if (MODUS == 2) { rootMeanSquareBuffer(bufferedAccelGData, accelGData); rootMeanSquareBuffer(bufferedMagnetData, magnetData); SensorManager.getRotationMatrix(rotationMatrix, null, bufferedAccelGData, bufferedMagnetData); } if (MODUS == 3) { rootMeanSquareBuffer(bufferedMagnetData, magnetData); SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, bufferedMagnetData); } if (MODUS == 4) { rootMeanSquareBuffer(bufferedAccelGData, accelGData); SensorManager.getRotationMatrix(rotationMatrix, null, bufferedAccelGData, magnetData); } if (MODUS == 5) { // this mode uses the sensor data recieved from the orientation // sensor resultingAngles = orientationData.clone(); if ((-90 > resultingAngles[1]) || (resultingAngles[1] > 90)) { resultingAngles[1] = orientationData[0]; resultingAngles[2] = orientationData[1]; resultingAngles[0] = orientationData[2]; } } if (MODUS == 6) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); final float[] anglesInRadians = new float[3]; SensorManager.getOrientation(rotationMatrix, anglesInRadians); if ((-90 < anglesInRadians[2] * rad2deg) && (anglesInRadians[2] * rad2deg < 90)) { // device camera is looking on the floor // this hemisphere is working fine mirrorOnBlueAxis = false; resultingAngles[0] = anglesInRadians[0] * rad2deg; resultingAngles[1] = anglesInRadians[1] * rad2deg; resultingAngles[2] = anglesInRadians[2] * -rad2deg; } else { mirrorOnBlueAxis = true; // device camera is looking in the sky // this hemisphere is mirrored at the blue axis resultingAngles[0] = (anglesInRadians[0] * rad2deg); resultingAngles[1] = (anglesInRadians[1] * rad2deg); resultingAngles[2] = (anglesInRadians[2] * rad2deg); } } if (MODUS == 7) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); rotationMatrix = transpose(rotationMatrix); /* * this assumes that the rotation matrices are multiplied in x y z * order Rx*Ry*Rz */ resultingAngles[2] = (float) (Math.asin(rotationMatrix[2])); final float cosB = (float) Math.cos(resultingAngles[2]); resultingAngles[2] = resultingAngles[2] * rad2deg; resultingAngles[0] = -(float) (Math.acos(rotationMatrix[0] / cosB)) * rad2deg; resultingAngles[1] = (float) (Math.acos(rotationMatrix[10] / cosB)) * rad2deg; } if (MODUS == 8) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); rotationMatrix = transpose(rotationMatrix); /* * this assumes that the rotation matrices are multiplied in z y x */ resultingAngles[2] = (float) (Math.asin(-rotationMatrix[8])); final float cosB = (float) Math.cos(resultingAngles[2]); resultingAngles[2] = resultingAngles[2] * rad2deg; resultingAngles[1] = (float) (Math.acos(rotationMatrix[9] / cosB)) * rad2deg; resultingAngles[0] = (float) (Math.asin(rotationMatrix[4] / cosB)) * rad2deg; } if (MODUS == 9) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); rotationMatrix = transpose(rotationMatrix); /* * this assumes that the rotation matrices are multiplied in z x y * * note z axis looks good at this one */ resultingAngles[1] = (float) (Math.asin(rotationMatrix[9])); final float minusCosA = -(float) Math.cos(resultingAngles[1]); resultingAngles[1] = resultingAngles[1] * rad2deg; resultingAngles[2] = (float) (Math.asin(rotationMatrix[8] / minusCosA)) * rad2deg; resultingAngles[0] = (float) (Math.asin(rotationMatrix[1] / minusCosA)) * rad2deg; } if (MODUS == 10) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); rotationMatrix = transpose(rotationMatrix); /* * this assumes that the rotation matrices are multiplied in y x z */ resultingAngles[1] = (float) (Math.asin(-rotationMatrix[6])); final float cosA = (float) Math.cos(resultingAngles[1]); resultingAngles[1] = resultingAngles[1] * rad2deg; resultingAngles[2] = (float) (Math.asin(rotationMatrix[2] / cosA)) * rad2deg; resultingAngles[0] = (float) (Math.acos(rotationMatrix[5] / cosA)) * rad2deg; } if (MODUS == 11) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); rotationMatrix = transpose(rotationMatrix); /* * this assumes that the rotation matrices are multiplied in y z x */ resultingAngles[0] = (float) (Math.asin(rotationMatrix[4])); final float cosC = (float) Math.cos(resultingAngles[0]); resultingAngles[0] = resultingAngles[0] * rad2deg; resultingAngles[2] = (float) (Math.acos(rotationMatrix[0] / cosC)) * rad2deg; resultingAngles[1] = (float) (Math.acos(rotationMatrix[5] / cosC)) * rad2deg; } if (MODUS == 12) { SensorManager.getRotationMatrix(rotationMatrix, null, accelGData, magnetData); rotationMatrix = transpose(rotationMatrix); /* * this assumes that the rotation matrices are multiplied in x z y */ resultingAngles[0] = (float) (Math.asin(-rotationMatrix[1])); final float cosC = (float) Math.cos(resultingAngles[0]); resultingAngles[0] = resultingAngles[0] * rad2deg; resultingAngles[2] = (float) (Math.acos(rotationMatrix[0] / cosC)) * rad2deg; resultingAngles[1] = (float) (Math.acos(rotationMatrix[5] / cosC)) * rad2deg; } logOutput(); } /** * transposes the matrix because it was transposted (inverted, but here its * the same, because its a rotation matrix) to be used for opengl * * @param source * @return */ private float[] transpose(float[] source) { final float[] result = source.clone(); if (TRY_TRANSPOSED_VERSION) { result[1] = source[4]; result[2] = source[8]; result[4] = source[1]; result[6] = source[9]; result[8] = source[2]; result[9] = source[6]; } // the other values in the matrix are not relevant for rotations return result; } private void rootMeanSquareBuffer(float[] target, float[] values) { final float amplification = 200.0f; float buffer = 20.0f; target[0] += amplification; target[1] += amplification; target[2] += amplification; values[0] += amplification; values[1] += amplification; values[2] += amplification; target[0] = (float) (Math .sqrt((target[0] * target[0] * buffer + values[0] * values[0]) / (1 + buffer))); target[1] = (float) (Math .sqrt((target[1] * target[1] * buffer + values[1] * values[1]) / (1 + buffer))); target[2] = (float) (Math .sqrt((target[2] * target[2] * buffer + values[2] * values[2]) / (1 + buffer))); target[0] -= amplification; target[1] -= amplification; target[2] -= amplification; values[0] -= amplification; values[1] -= amplification; values[2] -= amplification; } private void loadNewSensorData(SensorEvent event) { final int type = event.sensor.getType(); if (type == Sensor.TYPE_ACCELEROMETER) { accelGData = event.values.clone(); } if (type == Sensor.TYPE_MAGNETIC_FIELD) { magnetData = event.values.clone(); } if (type == Sensor.TYPE_ORIENTATION) { orientationData = event.values.clone(); } } private void logOutput() { if (mCount++ > 30) { mCount = 0; Log.d("Compass", "yaw0: " + (int) (resultingAngles[0]) + " pitch1: " + (int) (resultingAngles[1]) + " roll2: " + (int) (resultingAngles[2])); } } }

  Read the article

• Getting Selected Dropdown content to show in a form-generated email

  - by fmz

  I have a small contact form: <form method="post" action="contact.php" name="contactform" id="contactform"> <fieldset> <legend>Please fill in the following form to contact us</legend> <label for="name"><span class="required">*</span> Your Name</label> <input name="name" type="text" id="name" size="30" value="" /> <br /> <label for="company"><span class="required">*</span> Company</label> <input name="company" type="text" id="name" size="30" value="" /> <br /> <label for="email"><span class="required">*</span> Email</label> <input name="email" type="text" id="email" size="30" value="" /> <br /> <label for="phone"><span class="required">*</span> Phone</label> <input name="phone" type="text" id="phone" size="30" value="" /> <br /> <label for="purpose"><span class="required">*</span> Purpose</label> <select id="purpose" style="width: 300px; height:35px;"> <option value="I am interested in your services">I am interested in your services!</option> <option value="I am interested in a partnership">I am interested in a partnership!</option> <option value="I am interested in a job">I am interested in a job!</option> </select> <br /> <label for=comments><span class="required">*</span> Comments</label> <textarea name="comments" cols="40" rows="3" id="comments" style="width: 350px;"></textarea> <p><span class="required">*</span> Please help us control spam.</p> <label for=verify accesskey=V>&nbsp;&nbsp;&nbsp;3 + 1 =</label> <input name="verify" type="text" id="verify" size="4" value="" style="width: 30px;" /><br /><br /> <input type="submit" class="submit" id="submit" value="Submit" /> </fieldset> </form> I want to send the results of the form in a php generated email. Everything is coming through except the selected contents of the "purpose" drop down. Here is the PHP: <?php if(!$_POST) exit; $name = $_POST['name']; $company = $_POST['company']; $email = $_POST['email']; $phone = $_POST['phone']; $purpose = $_POST['purpose']; $comments = $_POST['comments']; $verify = $_POST['verify']; if(trim($name) == '') { echo '<div class="error_message">Attention! You must enter your name.</div>'; exit(); } else if(trim($company) == '') { echo '<div class="error_message">Attention! Please enter your company name.</div>'; exit(); } else if(trim($email) == '') { echo '<div class="error_message">Attention! Please enter a valid email address.</div>'; exit(); } else if(trim($phone) == '') { echo '<div class="error_message">Attention! Please enter a valid phone number.</div>'; exit(); } else if(!isEmail($email)) { echo '<div class="error_message">Attention! You have enter an invalid e-mail address, try again.</div>'; exit(); } if(trim($comments) == '') { echo '<div class="error_message">Attention! Please enter your message.</div>'; exit(); } else if(trim($verify) == '') { echo '<div class="error_message">Attention! Please enter the verification number.</div>'; exit(); } else if(trim($verify) != '4') { echo '<div class="error_message">Attention! The verification number you entered is incorrect.</div>'; exit(); } if($error == '') { if(get_magic_quotes_gpc()) { $comments = stripslashes($comments); } // Configuration option. // Enter the email address that you want to emails to be sent to. // Example $address = "[email protected]"; $address = "[email protected]"; // Configuration option. // i.e. The standard subject will appear as, "You've been contacted by John Doe." // Example, $e_subject = '$name . ' has contacted you via Your Website.'; $e_subject = 'You\'ve been contacted by ' . $name . '.'; // Configuration option. // You can change this if you feel that you need to. // Developers, you may wish to add more fields to the form, in which case you must be sure to add them here. $e_body = "You have been contacted by $name.\r\n\n"; $e_content = "Comments: \"$comments\"\r\n\n"; $e_company = "Company: $company\r\n\n"; $e_purpose = "Reason for contact: $purpose\r\n"; $e_reply = "You can contact $name via email, $email or via phone $phone"; $msg = $e_body . $e_content . $e_company . $e_purpose . $e_reply; if(mail($address, $e_subject, $msg, "From: $email\r\nReply-To: $email\r\nReturn-Path: $email\r\n")) { // Email has sent successfully, echo a success page. echo "<fieldset>"; echo "<div id='success_page'>"; echo "<h1>Email Sent Successfully.</h1>"; echo "<p>Thank you <strong>$name</strong>, your message has been submitted to us.</p>"; echo "</div>"; echo "</fieldset>"; } else { echo 'ERROR!'; } } function isEmail($email) { // Email address verification, do not edit. return(preg_match("/^[-_.[:alnum:]]+@((([[:alnum:]]|[[:alnum:]][[:alnum:]-]*[[:alnum:]])\.)+(ad|ae|aero|af|ag|ai|al|am|an|ao|aq|ar|arpa|as|at|au|aw|az|ba|bb|bd|be|bf|bg|bh|bi|biz|bj|bm|bn|bo|br|bs|bt|bv|bw|by|bz|ca|cc|cd|cf|cg|ch|ci|ck|cl|cm|cn|co|com|coop|cr|cs|cu|cv|cx|cy|cz|de|dj|dk|dm|do|dz|ec|edu|ee|eg|eh|er|es|et|eu|fi|fj|fk|fm|fo|fr|ga|gb|gd|ge|gf|gh|gi|gl|gm|gn|gov|gp|gq|gr|gs|gt|gu|gw|gy|hk|hm|hn|hr|ht|hu|id|ie|il|in|info|int|io|iq|ir|is|it|jm|jo|jp|ke|kg|kh|ki|km|kn|kp|kr|kw|ky|kz|la|lb|lc|li|lk|lr|ls|lt|lu|lv|ly|ma|mc|md|mg|mh|mil|mk|ml|mm|mn|mo|mp|mq|mr|ms|mt|mu|museum|mv|mw|mx|my|mz|na|name|nc|ne|net|nf|ng|ni|nl|no|np|nr|nt|nu|nz|om|org|pa|pe|pf|pg|ph|pk|pl|pm|pn|pr|pro|ps|pt|pw|py|qa|re|ro|ru|rw|sa|sb|sc|sd|se|sg|sh|si|sj|sk|sl|sm|sn|so|sr|st|su|sv|sy|sz|tc|td|tf|tg|th|tj|tk|tm|tn|to|tp|tr|tt|tv|tw|tz|ua|ug|uk|um|us|uy|uz|va|vc|ve|vg|vi|vn|vu|wf|ws|ye|yt|yu|za|zm|zw)$|(([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5])\.){3}([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5]))$/i",$email)); } ?> What am I missing? Thanks.

  Read the article

< Previous Page | 3 4 5 6 7