Search Results

Search found 640 results on 26 pages for 'zeta op'.

Page 7/26 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • Ubuntu 14.04, OpenLDAP TLS problems

    - by larsemil
    So i have set up an openldap server using this guide here. It worked fine. But as i want to use sssd i also need TLS to be working for ldap. So i looked into and followed the TLS part of the guide. And i never got any errors and slapd started fine again. BUT. It does not seem to work when i try to use ldap over tls. root@server:~# ldapsearch -x -ZZ -H ldap://83.209.243.253 -b dc=daladevelop,dc=se ldap_start_tls: Protocol error (2) additional info: unsupported extended operation Ganking up the debug level some notches returns some more information: root@server:~# ldapsearch -x -ZZ -H ldap://83.209.243.253 -b dc=daladevelop,dc=se -d 5 ldap_url_parse_ext(ldap://83.209.243.253) ldap_create ldap_url_parse_ext(ldap://83.209.243.253:389/??base) ldap_extended_operation_s ldap_extended_operation ldap_send_initial_request ldap_new_connection 1 1 0 ldap_int_open_connection ldap_connect_to_host: TCP 83.209.243.253:389 ldap_new_socket: 3 ldap_prepare_socket: 3 ldap_connect_to_host: Trying 83.209.243.253:389 ldap_pvt_connect: fd: 3 tm: -1 async: 0 ldap_open_defconn: successful ldap_send_server_request ber_scanf fmt ({it) ber: ber_scanf fmt ({) ber: ber_flush2: 31 bytes to sd 3 ldap_result ld 0x7f25df51e220 msgid 1 wait4msg ld 0x7f25df51e220 msgid 1 (infinite timeout) wait4msg continue ld 0x7f25df51e220 msgid 1 all 1 ** ld 0x7f25df51e220 Connections: * host: 83.209.243.253 port: 389 (default) refcnt: 2 status: Connected last used: Fri Jun 6 08:52:16 2014 ** ld 0x7f25df51e220 Outstanding Requests: * msgid 1, origid 1, status InProgress outstanding referrals 0, parent count 0 ld 0x7f25df51e220 request count 1 (abandoned 0) ** ld 0x7f25df51e220 Response Queue: Empty ld 0x7f25df51e220 response count 0 ldap_chkResponseList ld 0x7f25df51e220 msgid 1 all 1 ldap_chkResponseList returns ld 0x7f25df51e220 NULL ldap_int_select read1msg: ld 0x7f25df51e220 msgid 1 all 1 ber_get_next ber_get_next: tag 0x30 len 42 contents: read1msg: ld 0x7f25df51e220 msgid 1 message type extended-result ber_scanf fmt ({eAA) ber: read1msg: ld 0x7f25df51e220 0 new referrals read1msg: mark request completed, ld 0x7f25df51e220 msgid 1 request done: ld 0x7f25df51e220 msgid 1 res_errno: 2, res_error: <unsupported extended operation>, res_matched: <> ldap_free_request (origid 1, msgid 1) ldap_parse_extended_result ber_scanf fmt ({eAA) ber: ldap_parse_result ber_scanf fmt ({iAA) ber: ber_scanf fmt (}) ber: ldap_msgfree ldap_err2string ldap_start_tls: Protocol error (2) additional info: unsupported extended operation ldap_free_connection 1 1 ldap_send_unbind ber_flush2: 7 bytes to sd 3 ldap_free_connection: actually freed So no good information there neither. In /var/log/syslog i get: Jun 6 08:55:42 master slapd[21383]: conn=1008 fd=23 ACCEPT from IP=83.209.243.253:56440 (IP=0.0.0.0:389) Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 EXT oid=1.3.6.1.4.1.1466.20037 Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 do_extended: unsupported operation "1.3.6.1.4.1.1466.20037" Jun 6 08:55:42 master slapd[21383]: conn=1008 op=0 RESULT tag=120 err=2 text=unsupported extended operation Jun 6 08:55:42 master slapd[21383]: conn=1008 op=1 UNBIND Jun 6 08:55:42 master slapd[21383]: conn=1008 fd=23 closed If i portscan the host i get the following: Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-06 08:56 CEST Nmap scan report for h83-209-243-253.static.se.alltele.net (83.209.243.253) Host is up (0.0072s latency). Not shown: 996 closed ports PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 389/tcp open ldap 636/tcp open ldapssl But when i check certs root@master:~# openssl s_client -connect daladevelop.se:636 -showcerts -state CONNECTED(00000003) SSL_connect:before/connect initialization SSL_connect:unknown state 140244859233952:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:177: --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 317 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- And i feel like i am clearly out in deep water not knowing at all where to go from here. Anny hints appreciated on what to do or to get better debug logging... EDIT: This is my config slapcated from cn=config and it does not mention at all anything about TLS. I have inserted my certinfo.ldif: root@master:~# cat certinfo.ldif dn: cn=config add: olcTLSCACertificateFile olcTLSCACertificateFile: /etc/ssl/certs/cacert.pem - add: olcTLSCertificateFile olcTLSCertificateFile: /etc/ssl/certs/daladevelop_slapd_cert.pem - add: olcTLSCertificateKeyFile olcTLSCertificateKeyFile: /etc/ssl/private/daladevelop_slapd_key.pem and when doing that i only got this as an answer. root@master:~# sudo ldapmodify -Y EXTERNAL -H ldapi:/// -f certinfo.ldif SASL/EXTERNAL authentication started SASL username: gidNumber=0+uidNumber=0,cn=peercred,cn=external,cn=auth SASL SSF: 0 modifying entry "cn=config" So still no wiser.

    Read the article

  • Simple MSBuild Configuration: Updating Assemblies With A Version Number

    - by srkirkland
    When distributing a library you often run up against versioning problems, once facet of which is simply determining which version of that library your client is running.  Of course, each project in your solution has an AssemblyInfo.cs file which provides, among other things, the ability to set the Assembly name and version number.  Unfortunately, setting the assembly version here would require not only changing the version manually for each build (depending on your schedule), but keeping it in sync across all projects.  There are many ways to solve this versioning problem, and in this blog post I’m going to try to explain what I think is the easiest and most flexible solution.  I will walk you through using MSBuild to create a simple build script, and I’ll even show how to (optionally) integrate with a Team City build server.  All of the code from this post can be found at https://github.com/srkirkland/BuildVersion. Create CommonAssemblyInfo.cs The first step is to create a common location for the repeated assembly info that is spread across all of your projects.  Create a new solution-level file (I usually create a Build/ folder in the solution root, but anywhere reachable by all your projects will do) called CommonAssemblyInfo.cs.  In here you can put any information common to all your assemblies, including the version number.  An example CommonAssemblyInfo.cs is as follows: using System.Reflection; using System.Resources; using System.Runtime.InteropServices;   [assembly: AssemblyCompany("University of California, Davis")] [assembly: AssemblyProduct("BuildVersionTest")] [assembly: AssemblyCopyright("Scott Kirkland & UC Regents")] [assembly: AssemblyConfiguration("")] [assembly: AssemblyTrademark("")]   [assembly: ComVisible(false)]   [assembly: AssemblyVersion("1.2.3.4")] //Will be replaced   [assembly: NeutralResourcesLanguage("en-US")] .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   Cleanup AssemblyInfo.cs & Link CommonAssemblyInfo.cs For each of your projects, you’ll want to clean up your assembly info to contain only information that is unique to that assembly – everything else will go in the CommonAssemblyInfo.cs file.  For most of my projects, that just means setting the AssemblyTitle, though you may feel AssemblyDescription is warranted.  An example AssemblyInfo.cs file is as follows: using System.Reflection;   [assembly: AssemblyTitle("BuildVersionTest")] .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Next, you need to “link” the CommonAssemblyinfo.cs file into your projects right beside your newly lean AssemblyInfo.cs file.  To do this, right click on your project and choose Add | Existing Item from the context menu.  Navigate to your CommonAssemblyinfo.cs file but instead of clicking Add, click the little down-arrow next to add and choose “Add as Link.”  You should see a little link graphic similar to this: We’ve actually reduced complexity a lot already, because if you build all of your assemblies will have the same common info, including the product name and our static (fake) assembly version.  Let’s take this one step further and introduce a build script. Create an MSBuild file What we want from the build script (for now) is basically just to have the common assembly version number changed via a parameter (eventually to be passed in by the build server) and then for the project to build.  Also we’d like to have a flexibility to define what build configuration to use (debug, release, etc). In order to find/replace the version number, we are going to use a Regular Expression to find and replace the text within your CommonAssemblyInfo.cs file.  There are many other ways to do this using community build task add-ins, but since we want to keep it simple let’s just define the Regular Expression task manually in a new file, Build.tasks (this example taken from the NuGet build.tasks file). <?xml version="1.0" encoding="utf-8"?> <Project ToolsVersion="4.0" DefaultTargets="Go" xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> <UsingTask TaskName="RegexTransform" TaskFactory="CodeTaskFactory" AssemblyFile="$(MSBuildToolsPath)\Microsoft.Build.Tasks.v4.0.dll"> <ParameterGroup> <Items ParameterType="Microsoft.Build.Framework.ITaskItem[]" /> </ParameterGroup> <Task> <Using Namespace="System.IO" /> <Using Namespace="System.Text.RegularExpressions" /> <Using Namespace="Microsoft.Build.Framework" /> <Code Type="Fragment" Language="cs"> <![CDATA[ foreach(ITaskItem item in Items) { string fileName = item.GetMetadata("FullPath"); string find = item.GetMetadata("Find"); string replaceWith = item.GetMetadata("ReplaceWith"); if(!File.Exists(fileName)) { Log.LogError(null, null, null, null, 0, 0, 0, 0, String.Format("Could not find version file: {0}", fileName), new object[0]); } string content = File.ReadAllText(fileName); File.WriteAllText( fileName, Regex.Replace( content, find, replaceWith ) ); } ]]> </Code> </Task> </UsingTask> </Project> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } If you glance at the code, you’ll see it’s really just going a Regex.Replace() on a given file, which is exactly what we need. Now we are ready to write our build file, called (by convention) Build.proj. <?xml version="1.0" encoding="utf-8"?> <Project ToolsVersion="4.0" DefaultTargets="Go" xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> <Import Project="$(MSBuildProjectDirectory)\Build.tasks" /> <PropertyGroup> <Configuration Condition="'$(Configuration)' == ''">Debug</Configuration> <SolutionRoot>$(MSBuildProjectDirectory)</SolutionRoot> </PropertyGroup>   <ItemGroup> <RegexTransform Include="$(SolutionRoot)\CommonAssemblyInfo.cs"> <Find>(?&lt;major&gt;\d+)\.(?&lt;minor&gt;\d+)\.\d+\.(?&lt;revision&gt;\d+)</Find> <ReplaceWith>$(BUILD_NUMBER)</ReplaceWith> </RegexTransform> </ItemGroup>   <Target Name="Go" DependsOnTargets="UpdateAssemblyVersion; Build"> </Target>   <Target Name="UpdateAssemblyVersion" Condition="'$(BUILD_NUMBER)' != ''"> <RegexTransform Items="@(RegexTransform)" /> </Target>   <Target Name="Build"> <MSBuild Projects="$(SolutionRoot)\BuildVersionTest.sln" Targets="Build" /> </Target>   </Project> Reviewing this MSBuild file, we see that by default the “Go” target will be called, which in turn depends on “UpdateAssemblyVersion” and then “Build.”  We go ahead and import the Bulid.tasks file and then setup some handy properties for setting the build configuration and solution root (in this case, my build files are in the solution root, but we might want to create a Build/ directory later).  The rest of the file flows logically, we setup the RegexTransform to match version numbers such as <major>.<minor>.1.<revision> (1.2.3.4 in our example) and replace it with a $(BUILD_NUMBER) parameter which will be supplied externally.  The first target, “UpdateAssemblyVersion” just runs the RegexTransform, and the second target, “Build” just runs the default MSBuild on our solution. Testing the MSBuild file locally Now we have a build file which can replace assembly version numbers and build, so let’s setup a quick batch file to be able to build locally.  To do this you simply create a file called Build.cmd and have it call MSBuild on your Build.proj file.  I’ve added a bit more flexibility so you can specify build configuration and version number, which makes your Build.cmd look as follows: set config=%1 if "%config%" == "" ( set config=debug ) set version=%2 if "%version%" == "" ( set version=2.3.4.5 ) %WINDIR%\Microsoft.NET\Framework\v4.0.30319\msbuild Build.proj /p:Configuration="%config%" /p:build_number="%version%" .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Now if you click on the Build.cmd file, you will get a default debug build using the version 2.3.4.5.  Let’s run it in a command window with the parameters set for a release build version 2.0.1.453.   Excellent!  We can now run one simple command and govern the build configuration and version number of our entire solution.  Each DLL produced will have the same version number, making determining which version of a library you are running very simple and accurate. Configure the build server (TeamCity) Of course you are not really going to want to run a build command manually every time, and typing in incrementing version numbers will also not be ideal.  A good solution is to have a computer (or set of computers) act as a build server and build your code for you, providing you a consistent environment, excellent reporting, and much more.  One of the most popular Build Servers is JetBrains’ TeamCity, and this last section will show you the few configuration parameters to use when setting up a build using your MSBuild file created earlier.  If you are using a different build server, the same principals should apply. First, when setting up the project you want to specify the “Build Number Format,” often given in the form <major>.<minor>.<revision>.<build>.  In this case you will set major/minor manually, and optionally revision (or you can use your VCS revision number with %build.vcs.number%), and then build using the {0} wildcard.  Thus your build number format might look like this: 2.0.1.{0}.  During each build, this value will be created and passed into the $BUILD_NUMBER variable of our Build.proj file, which then uses it to decorate your assemblies with the proper version. After setting up the build number, you must choose MSBuild as the Build Runner, then provide a path to your build file (Build.proj).  After specifying your MSBuild Version (equivalent to your .NET Framework Version), you have the option to specify targets (the default being “Go”) and additional MSBuild parameters.  The one parameter that is often useful is manually setting the configuration property (/p:Configuration="Release") if you want something other than the default (which is Debug in our example).  Your resulting configuration will look something like this: [Under General Settings] [Build Runner Settings]   Now every time your build is run, a newly incremented build version number will be generated and passed to MSBuild, which will then version your assemblies and build your solution.   A Quick Review Our goal was to version our output assemblies in an automated way, and we accomplished it by performing a few quick steps: Move the common assembly information, including version, into a linked CommonAssemblyInfo.cs file Create a simple MSBuild script to replace the common assembly version number and build your solution Direct your build server to use the created MSBuild script That’s really all there is to it.  You can find all of the code from this post at https://github.com/srkirkland/BuildVersion. Enjoy!

    Read the article

  • Introducing Data Annotations Extensions

    - by srkirkland
    Validation of user input is integral to building a modern web application, and ASP.NET MVC offers us a way to enforce business rules on both the client and server using Model Validation.  The recent release of ASP.NET MVC 3 has improved these offerings on the client side by introducing an unobtrusive validation library built on top of jquery.validation.  Out of the box MVC comes with support for Data Annotations (that is, System.ComponentModel.DataAnnotations) and can be extended to support other frameworks.  Data Annotations Validation is becoming more popular and is being baked in to many other Microsoft offerings, including Entity Framework, though with MVC it only contains four validators: Range, Required, StringLength and Regular Expression.  The Data Annotations Extensions project attempts to augment these validators with additional attributes while maintaining the clean integration Data Annotations provides. A Quick Word About Data Annotations Extensions The Data Annotations Extensions project can be found at http://dataannotationsextensions.org/, and currently provides 11 additional validation attributes (ex: Email, EqualTo, Min/Max) on top of Data Annotations’ original 4.  You can find a current list of the validation attributes on the afore mentioned website. The core library provides server-side validation attributes that can be used in any .NET 4.0 project (no MVC dependency). There is also an easily pluggable client-side validation library which can be used in ASP.NET MVC 3 projects using unobtrusive jquery validation (only MVC3 included javascript files are required). On to the Preview Let’s say you had the following “Customer” domain model (or view model, depending on your project structure) in an MVC 3 project: public class Customer { public string Email { get; set; } public int Age { get; set; } public string ProfilePictureLocation { get; set; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } When it comes time to create/edit this Customer, you will probably have a CustomerController and a simple form that just uses one of the Html.EditorFor() methods that the ASP.NET MVC tooling generates for you (or you can write yourself).  It should look something like this: With no validation, the customer can enter nonsense for an email address, and then can even report their age as a negative number!  With the built-in Data Annotations validation, I could do a bit better by adding a Range to the age, adding a RegularExpression for email (yuck!), and adding some required attributes.  However, I’d still be able to report my age as 10.75 years old, and my profile picture could still be any string.  Let’s use Data Annotations along with this project, Data Annotations Extensions, and see what we can get: public class Customer { [Email] [Required] public string Email { get; set; }   [Integer] [Min(1, ErrorMessage="Unless you are benjamin button you are lying.")] [Required] public int Age { get; set; }   [FileExtensions("png|jpg|jpeg|gif")] public string ProfilePictureLocation { get; set; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Now let’s try to put in some invalid values and see what happens: That is very nice validation, all done on the client side (will also be validated on the server).  Also, the Customer class validation attributes are very easy to read and understand. Another bonus: Since Data Annotations Extensions can integrate with MVC 3’s unobtrusive validation, no additional scripts are required! Now that we’ve seen our target, let’s take a look at how to get there within a new MVC 3 project. Adding Data Annotations Extensions To Your Project First we will File->New Project and create an ASP.NET MVC 3 project.  I am going to use Razor for these examples, but any view engine can be used in practice.  Now go into the NuGet Extension Manager (right click on references and select add Library Package Reference) and search for “DataAnnotationsExtensions.”  You should see the following two packages: The first package is for server-side validation scenarios, but since we are using MVC 3 and would like comprehensive sever and client validation support, click on the DataAnnotationsExtensions.MVC3 project and then click Install.  This will install the Data Annotations Extensions server and client validation DLLs along with David Ebbo’s web activator (which enables the validation attributes to be registered with MVC 3). Now that Data Annotations Extensions is installed you have all you need to start doing advanced model validation.  If you are already using Data Annotations in your project, just making use of the additional validation attributes will provide client and server validation automatically.  However, assuming you are starting with a blank project I’ll walk you through setting up a controller and model to test with. Creating Your Model In the Models folder, create a new User.cs file with a User class that you can use as a model.  To start with, I’ll use the following class: public class User { public string Email { get; set; } public string Password { get; set; } public string PasswordConfirm { get; set; } public string HomePage { get; set; } public int Age { get; set; } } Next, create a simple controller with at least a Create method, and then a matching Create view (note, you can do all of this via the MVC built-in tooling).  Your files will look something like this: UserController.cs: public class UserController : Controller { public ActionResult Create() { return View(new User()); }   [HttpPost] public ActionResult Create(User user) { if (!ModelState.IsValid) { return View(user); }   return Content("User valid!"); } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Create.cshtml: @model NuGetValidationTester.Models.User   @{ ViewBag.Title = "Create"; }   <h2>Create</h2>   <script src="@Url.Content("~/Scripts/jquery.validate.min.js")" type="text/javascript"></script> <script src="@Url.Content("~/Scripts/jquery.validate.unobtrusive.min.js")" type="text/javascript"></script>   @using (Html.BeginForm()) { @Html.ValidationSummary(true) <fieldset> <legend>User</legend> @Html.EditorForModel() <p> <input type="submit" value="Create" /> </p> </fieldset> } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } In the Create.cshtml view, note that we are referencing jquery validation and jquery unobtrusive (jquery is referenced in the layout page).  These MVC 3 included scripts are the only ones you need to enjoy both the basic Data Annotations validation as well as the validation additions available in Data Annotations Extensions.  These references are added by default when you use the MVC 3 “Add View” dialog on a modification template type. Now when we go to /User/Create we should see a form for editing a User Since we haven’t yet added any validation attributes, this form is valid as shown (including no password, email and an age of 0).  With the built-in Data Annotations attributes we can make some of the fields required, and we could use a range validator of maybe 1 to 110 on Age (of course we don’t want to leave out supercentenarians) but let’s go further and validate our input comprehensively using Data Annotations Extensions.  The new and improved User.cs model class. { [Required] [Email] public string Email { get; set; }   [Required] public string Password { get; set; }   [Required] [EqualTo("Password")] public string PasswordConfirm { get; set; }   [Url] public string HomePage { get; set; }   [Integer] [Min(1)] public int Age { get; set; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Now let’s re-run our form and try to use some invalid values: All of the validation errors you see above occurred on the client, without ever even hitting submit.  The validation is also checked on the server, which is a good practice since client validation is easily bypassed. That’s all you need to do to start a new project and include Data Annotations Extensions, and of course you can integrate it into an existing project just as easily. Nitpickers Corner ASP.NET MVC 3 futures defines four new data annotations attributes which this project has as well: CreditCard, Email, Url and EqualTo.  Unfortunately referencing MVC 3 futures necessitates taking an dependency on MVC 3 in your model layer, which may be unadvisable in a multi-tiered project.  Data Annotations Extensions keeps the server and client side libraries separate so using the project’s validation attributes don’t require you to take any additional dependencies in your model layer which still allowing for the rich client validation experience if you are using MVC 3. Custom Error Message and Globalization: Since the Data Annotations Extensions are build on top of Data Annotations, you have the ability to define your own static error messages and even to use resource files for very customizable error messages. Available Validators: Please see the project site at http://dataannotationsextensions.org/ for an up-to-date list of the new validators included in this project.  As of this post, the following validators are available: CreditCard Date Digits Email EqualTo FileExtensions Integer Max Min Numeric Url Conclusion Hopefully I’ve illustrated how easy it is to add server and client validation to your MVC 3 projects, and how to easily you can extend the available validation options to meet real world needs. The Data Annotations Extensions project is fully open source under the BSD license.  Any feedback would be greatly appreciated.  More information than you require, along with links to the source code, is available at http://dataannotationsextensions.org/. Enjoy!

    Read the article

  • Working with Tile Notifications in Windows 8 Store Apps – Part I

    - by dwahlin
    One of the features that really makes Windows 8 apps stand out from others is the tile functionality on the start screen. While icons allow a user to start an application, tiles provide a more engaging way to engage the user and draw them into an application. Examples of “live” tiles on part of my current start screen are shown next: I’ll admit that if you get enough of these tiles going the start screen can actually be a bit distracting. Fortunately, a user can easily disable a live tile by right-clicking on it or pressing and holding a tile on a touch device and then selecting Turn live tile off from the AppBar: The can also make a wide tile smaller (into a square tile) or make a square tile bigger assuming the application supports both squares and rectangles. In this post I’ll walk through how to add tile notification functionality into an application. Both XAML/C# and HTML/JavaScript apps support live tiles and I’ll show the code for both options.   Understanding Tile Templates The first thing you need to know if you want to add custom tile functionality (live tiles) into your application is that there is a collection of tile templates available out-of-the-box. Each tile template has XML associated with it that you need to load, update with your custom data, and then feed into a tile update manager. By doing that you can control what shows in your app’s tile on the Windows 8 start screen. So how do you learn more about the different tile templates and their respective XML? Fortunately, Microsoft has a nice documentation page in the Windows 8 Store SDK. Visit http://msdn.microsoft.com/en-us/library/windows/apps/hh761491.aspx to see a complete list of square and wide/rectangular tile templates that you can use. Looking through the templates you’ll It has the following XML template associated with it:  <tile> <visual> <binding template="TileSquareBlock"> <text id="1">Text Field 1</text> <text id="2">Text Field 2</text> </binding> </visual> </tile> An example of a wide/rectangular tile template is shown next:    <tile> <visual> <binding template="TileWideImageAndText01"> <image id="1" src="image1.png" alt="alt text"/> <text id="1">Text Field 1</text> </binding> </visual> </tile>   To use these tile templates (or others you find interesting), update their content, and get them to show for your app’s tile on the Windows 8 start screen you’ll need to perform the following steps: Define the tile template to use in your app Load the tile template’s XML into memory Modify the children of the <binding> tag Feed the modified tile XML into a new TileNotification instance Feed the TileNotification instance into the Update() method of the TileUpdateManager In the remainder of the post I’ll walk through each of the steps listed above to provide wide and square tile notifications for an application. The wide tile that’s shown will show an image and text while the square tile will only show text. If you’re going to provide custom tile notifications it’s recommended that you provide wide and square tiles since users can switch between the two of them directly on the start screen. Note: When working with tile notifications it’s possible to manipulate and update a tile’s XML template without having to know XML parsing techniques. This can be accomplished using some C# notification extension classes that are available. In this post I’m going to focus on working with tile notifications using an XML parser so that the focus is on the steps required to add notifications to the Windows 8 start screen rather than on external extension classes. You can access the extension classes in the Windows 8 samples gallery if you’re interested.   Steps to Create Custom App Tile Notifications   Step 1: Define the tile template to use in your app Although you can cut-and-paste a tile template’s XML directly into your C# or HTML/JavaScript Windows store app and then parse it using an XML parser, it’s easier to use the built-in TileTemplateType enumeration from the Windows.UI.Notifications namespace. It provides direct access to the XML for the various templates so once you locate a template you like in the documentation (mentioned above), simplify reference it:HTML/JavaScript var notifications = Windows.UI.Notifications; var template = notifications.TileTemplateType.tileWideImageAndText01; .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   XAML/C# var template = TileTemplateType.TileWideImageAndText01;   Step 2: Load the tile template’s XML into memory Once the target template’s XML is identified, load it into memory using the TileUpdateManager’s GetTemplateContent() method. This method parses the template XML and returns an XmlDocument object:   HTML/JavaScript   var tileXml = notifications.TileUpdateManager.getTemplateContent(template); .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   XAML/C#  var tileXml = TileUpdateManager.GetTemplateContent(template);   Step 3: Modify the children of the <binding> tag Once the XML for a given template is loaded into memory you need to locate the appropriate <image> and/or <text> elements in the XML and update them with your app data. This can be done using standard XML DOM manipulation techniques. The example code below locates the image folder and loads the path to an image file located in the project into it’s inner text. The code also creates a square tile that consists of text, updates it’s <text> element, and then imports and appends it into the wide tile’s XML.   HTML/JavaScript var image = tileXml.selectSingleNode('//image[@id="1"]'); image.setAttribute('src', 'ms-appx:///images/' + imageFile); image.setAttribute('alt', 'Live Tile'); var squareTemplate = notifications.TileTemplateType.tileSquareText04; var squareTileXml = notifications.TileUpdateManager.getTemplateContent(squareTemplate); var squareTileTextAttributes = squareTileXml.selectSingleNode('//text[@id="1"]'); squareTileTextAttributes.appendChild(squareTileXml.createTextNode(content)); var node = tileXml.importNode(squareTileXml.selectSingleNode('//binding'), true); tileXml.selectSingleNode('//visual').appendChild(node); .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   XAML/C#var tileXml = TileUpdateManager.GetTemplateContent(template); var text = tileXml.SelectSingleNode("//text[@id='1']"); text.AppendChild(tileXml.CreateTextNode(content)); var image = (XmlElement)tileXml.SelectSingleNode("//image[@id='1']"); image.SetAttribute("src", "ms-appx:///Assets/" + imageFile); image.SetAttribute("alt", "Live Tile"); Debug.WriteLine(image.GetXml()); var squareTemplate = TileTemplateType.TileSquareText04; var squareTileXml = TileUpdateManager.GetTemplateContent(squareTemplate); var squareTileTextAttributes = squareTileXml.SelectSingleNode("//text[@id='1']"); squareTileTextAttributes.AppendChild(squareTileXml.CreateTextNode(content)); var node = tileXml.ImportNode(squareTileXml.SelectSingleNode("//binding"), true); tileXml.SelectSingleNode("//visual").AppendChild(node);  Step 4: Feed the modified tile XML into a new TileNotification instance Now that the XML data has been updated with the desired text and images, it’s time to load the XmlDocument object into a new TileNotification instance:   HTML/JavaScript var tileNotification = new notifications.TileNotification(tileXml); .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   XAML/C#var tileNotification = new TileNotification(tileXml);  Step 5: Feed the TileNotification instance into the Update() method of the TileUpdateManager Once the TileNotification instance has been created and the XmlDocument has been passed to its constructor, it needs to be passed to the Update() method of a TileUpdator in order to be shown on the Windows 8 start screen:   HTML/JavaScript notifications.TileUpdateManager.createTileUpdaterForApplication().update(tileNotification); .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   XAML/C#TileUpdateManager.CreateTileUpdaterForApplication().Update(tileNotification);    Once the tile notification is updated it’ll show up on the start screen. An example of the wide and square tiles created with the included demo code are shown next:     Download the HTML/JavaScript and XAML/C# sample application here. In the next post in this series I’ll walk through how to queue multiple tiles and clear a queue.

    Read the article

  • Using TypeScript in ASP.NET MVC Projects

    - by shiju
    In the previous blog post Microsoft TypeScript : A Typed Superset of JavaScript, I have given a brief introduction on TypeScript. In this post, I will demonstrate how to use TypeScript with ASP.NET MVC projects and how we can compile TypeScript within the ASP.NET MVC projects. Using TypeScript with ASP.NET MVC 3 Projects The Visual Studio plug-in for TypeScript provides an ASP.NET MVC 3 project template for TypeScript that lets you to compile TypeScript from the Visual Studio. The following screen shot shows the TypeScript template for ASP.NET MVC 3 project The “TypeScript Internet Application” template is just a ASP.NET MVC 3 internet application project template which will allows to compile TypeScript programs to JavaScript when you are building your ASP.NET MVC projects. This project template will have the following section in the .csproject file <None Include="Scripts\jquery.d.ts" /> <TypeScriptCompile Include="Scripts\site.ts" /> <Content Include="Scripts\site.js"> <DependentUpon>site.ts</DependentUpon> </Content> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } <Target Name="BeforeBuild"> <Exec Command="&amp;quot;$(PROGRAMFILES)\ Microsoft SDKs\TypeScript\0.8.0.0\tsc&amp;quot; @(TypeScriptCompile ->'&quot;%(fullpath)&quot;', ' ')" /> </Target> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } The “BeforeBuild” target will allows you to compile TypeScript programs when you are building your ASP.NET MVC projects. The TypeScript project template will provide a typing reference file for the jQuery library named “jquery.d.ts”. The following default app.ts file referenced to jquery.d.ts 1: ///<reference path='jquery.d.ts' /> 2:   3: $(document).ready(function () { 4:   5: $(".btn-slide").click(function () { 6: $("#main").slideToggle("slow"); 7: $(this).toggleClass("active"); 8: }); 9:   10: }); .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Using TypeScript with ASP.NET MVC 4 Projects The current preview version of TypeScript is not providing a project template for ASP.NET MVC 4 projects. But you can use TypeScript with ASP.NET MVC 4 projects by editing the project’s .csproject file. You can take the necessary settings from ASP.NET MVC 3 project file. I have just added the following section in the end of the .csproj file of a ASP.NET MVC 4 project, which will allows to compile all TypeScript when building ASP.NET MVC 4 project. <ItemGroup> <TypeScriptCompile Include="$(ProjectDir)\**\*.ts" /> </ItemGroup> <Target Name="BeforeBuild"> <Exec Command="&amp;quot;$(PROGRAMFILES)\ Microsoft SDKs\TypeScript\0.8.0.0\tsc&amp;quot; @(TypeScriptCompile ->'&quot;%(fullpath)&quot;', ' ')" /> </Target> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }

    Read the article

  • Clarity is important, both in question and in answer.

    - by gerrylowry
    clarity is important ... i'm often reminded of the Clouseau movie in which Peter Sellers as Chief Inspector Clouseau asks a hotel clerk "Does your dog bite?" ... the clerk answers "no" ... after Clouseau has been bitten by the dog, he looks at the hotel clerk who says "That's not my dog".  Clarity is important, both in question and in answer. i've been a member of forums.asp.net since 2008 ... like many of my peers at forums.asp.net, i've answered my fair share of questions. FWIW, the purpose of this, my first web log post to http://weblogs.asp.net/gerrylowry is to help new members ask better questions and in turn get better answers. TIMTOWTDI  =.  there is more than one way to do it imho, the best way to ask a question in any forum, or even person to person, is to first formulate your question and then ask yourself to answer your own question. Things to consider when asking (the more complete your question, the more likely you'll get the answer you require): -- have you searched Google and/or your favourite search engine(s) before posting your question to forums.asp.net; examples: site:msdn.microsoft.com entity framework 5.0 c#http://lmgtfy.com/?q=site%3Amsdn.microsoft.com+entity+framework+5.0+c%23 site:forums.asp.net MVC tutorial c#http://lmgtfy.com/?q=site%3Aforums.asp.net+MVC+tutorial+c%23 -- are you asking your question in the correct forum?  look at the forums' descriptions at http://forums.asp.net/; examples: Getting Started If you have a general ASP.NET question on a topic that's not covered by one of the other more specific forums - ask it here. MVC Discussions regarding ASP.NET Model-View-Controller (MVC) C# Questions about using C# for ASP.NET development Note:  if your question pertains more to c# than to MVC, choosing the C# forum is likely to be more appropriate. -- is your post subject clear and concise, yet not too vague? compare these three subjects (all three had something to do with GridView):     (1)    please help     (2)    gridview      (3)    How to show newline in GridView  -- have you clearly explained your scenario? compare:  my leg hurts   with   when i walk too much, my right knee hurts in the knee joint  compare:  my code does not work    with    when i enter a date as 2012-11-8, i get a FormatException -- have you checked your spelling, your grammar, and your English? for better or worse, English is the language of forums.asp.net ... many of the currently 170000++ forums.asp.net are not native speakers of English; that's okay ... however, there are times when choosing the more appropriate words will likely get one a better answer; fortunately, there are web tools to help you formulate your question, for example, http://translate.google.com/.  -- have you provided relevant information about your environment? here are a few examples ... feel free to include other items to your question ... rule of thumb:  if you think a given detail is relevant, it likely is -- what technology are you using?    ASP.NET MVC 4, ASP.NET MVC 3, WebForms, ...  -- what version of Visual Studio are you using?  vs2012 (ultimate, professional, express), vs2010, vs2008 ... -- are you hosting your own website?  are you using a shared hosting service? -- are you experience difficulties in just one browser? more than one browser? -- what browser version(s) are you using?   ie8? ie9? ... -- what is your operating system?     win8, win7, vista, XP, server 2008 R2 ... -- what is your database?   SQL Server 2008 R2, ss2005, MySQL, Oracle, ... -- what is your web server?  iis 7.5, iis 6, .... -- have you provided enough information for someone to be able to answer your question? Here's an actual example from an O.P. that i hope is self-explanatory: I'm trying to make a simple calculator when i write the code in windows application it worked when i tried it in web application it doesn't work and there are no errors what should i do ??!! -- have you included unnecessary information? more than once, i've seen the O.P. (original post, original poster) include many extra lines of code that were not relevant to the actual question; the more unnecessary code that you include, the less likely your volunteer peers will be motivated to donate their time to help you. -- have you asked the question that you want answered? "Does this dog bite?" -- are your expectations reasonable? -- generally, persons who are going to answer your questions are your peers ... they are unpaid volunteers ... -- are you looking for help with your homework, work assignment, or hobby? or, are you expecting someone else to do your work for you?  -- do you expect a complete solution or are you simply looking for guidance and direction? -- you are likely to get more help by first making a reasonable effort to help yourself first Clarity is important, both in question and in answer. if you are answering someone else's question, please remember that clear answers are just as important as clear questions; would you understand your own answer? Things to consider when answering: -- have you tested your code example?  if you have, say so; if you've not tested your code example, also say so -- imho, it's okay to guess as long as you clearly state that you're guessing ... sometimes a wrong guess can still help the O.P. find her/his way to the right answer -- meanness does not contribute to being helpful; sometimes one may become frustrated with the O.P. and/or others participating in a thread, if that happens to you, be kind regardless; speaking from my own experience, at least once i've allowed myself to be frustrated into writing something inappropriate that i've regretted later ... being a meany does not feel good ... being kind and helpful feels fantastic! Tip:  before asking your question, read more than a few existing questions and answers to get a sense of how your peers ask and answer questions. Gerry P.S.:  try to avoid necroposting and piggy backing. necroposting is adding to an old post, especially one that was resolved months ago. piggy backing is adding your own question to someone else's thread.

    Read the article

  • Clarity is important, both in question and in answer.

    - by gerrylowry
    clarity is important ... i'm often reminded of the Clouseau movie in which Peter Sellers as Chief Inspector Clouseau asks a hotel clerk "Does your dog bite?" ... the clerk answers "no" ... after Clouseau has been bitten by the dog, he looks at the hotel clerk who says "That's not my dog".  Clarity is important, both in question and in answer. i've been a member of forums.asp.net since 2008 ... like many of my peers at forums.asp.net, i've answered my fair share of questions. FWIW, the purpose of this, my first web log post to http://weblogs.asp.net/gerrylowry is to help new members ask better questions and in turn get better answers. TIMTOWTDI  =.  there is more than one way to do it imho, the best way to ask a question in any forum, or even person to person, is to first formulate your question and then ask yourself to answer your own question. Things to consider when asking (the more complete your question, the more likely you'll get the answer you require): -- have you searched Google and/or your favourite search engine(s) before posting your question to forums.asp.net; examples: site:msdn.microsoft.com entity framework 5.0 c#http://lmgtfy.com/?q=site%3Amsdn.microsoft.com+entity+framework+5.0+c%23 site:forums.asp.net MVC tutorial c#http://lmgtfy.com/?q=site%3Aforums.asp.net+MVC+tutorial+c%23 -- are you asking your question in the correct forum?  look at the forums' descriptions at http://forums.asp.net/; examples: Getting Started If you have a general ASP.NET question on a topic that's not covered by one of the other more specific forums - ask it here. MVC Discussions regarding ASP.NET Model-View-Controller (MVC) C# Questions about using C# for ASP.NET development Note:  if your question pertains more to c# than to MVC, choosing the C# forum is likely to be more appropriate. -- is your post subject clear and concise, yet not too vague? compare these three subjects (all three had something to do with GridView):     (1)    please help     (2)    gridview      (3)    How to show newline in GridView  -- have you clearly explained your scenario? compare:  my leg hurts   with   when i walk too much, my right knee hurts in the knee joint  compare:  my code does not work    with    when i enter a date as 2012-11-8, i get a FormatException -- have you checked your spelling, your grammar, and your English? for better or worse, English is the language of forums.asp.net ... many of the currently 170000++ forums.asp.net are not native speakers of English; that's okay ... however, there are times when choosing the more appropriate words will likely get one a better answer; fortunately, there are web tools to help you formulate your question, for example, http://translate.google.com/.  -- have you provided relevant information about your environment? here are a few examples ... feel free to include other items to your question ... rule of thumb:  if you think a given detail is relevant, it likely is -- what technology are you using?    ASP.NET MVC 4, ASP.NET MVC 3, WebForms, ...  -- what version of Visual Studio are you using?  vs2012 (ultimate, professional, express), vs2010, vs2008 ... -- are you hosting your own website?  are you using a shared hosting service? -- are you experience difficulties in just one browser? more than one browser? -- what browser version(s) are you using?   ie8? ie9? ... -- what is your operating system?     win8, win7, vista, XP, server 2008 R2 ... -- what is your database?   SQL Server 2008 R2, ss2005, MySQL, Oracle, ... -- what is your web server?  iis 7.5, iis 6, .... -- have you provided enough information for someone to be able to answer your question? Here's an actual example from an O.P. that i hope is self-explanatory: I'm trying to make a simple calculator when i write the code in windows application it worked when i tried it in web application it doesn't work and there are no errors what should i do ??!! -- have you included unnecessary information? more than once, i've seen the O.P. (original post, original poster) include many extra lines of code that were not relevant to the actual question; the more unnecessary code that you include, the less likely your volunteer peers will be motivated to donate their time to help you. -- have you asked the question that you want answered? "Does this dog bite?" -- are your expectations reasonable? -- generally, persons who are going to answer your questions are your peers ... they are unpaid volunteers ... -- are you looking for help with your homework, work assignment, or hobby? or, are you expecting someone else to do your work for you?  -- do you expect a complete solution or are you simply looking for guidance and direction? -- you are likely to get more help by first making a reasonable effort to help yourself first Clarity is important, both in question and in answer. if you are answering someone else's question, please remember that clear answers are just as important as clear questions; would you understand your own answer? Things to consider when answering: -- have you tested your code example?  if you have, say so; if you've not tested your code example, also say so -- imho, it's okay to guess as long as you clearly state that you're guessing ... sometimes a wrong guess can still help the O.P. find her/his way to the right answer -- meanness does not contribute to being helpful; sometimes one may become frustrated with the O.P. and/or others participating in a thread, if that happens to you, be kind regardless; speaking from my own experience, at least once i've allowed myself to be frustrated into writing something inappropriate that i've regretted later ... being a meany does not feel good ... being kind and helpful feels fantastic! Tip:  before asking your question, read more than a few existing questions and answers to get a sense of how your peers ask and answer questions. Gerry P.S.:  try to avoid necroposting and piggy backing. necroposting is adding to an old post, especially one that was resolved months ago. piggy backing is adding your own question to someone else's thread.

    Read the article

  • Mscorlib mocking minus the attribute

    - by mehfuzh
    Mocking .net framework members (a.k.a. mscorlib) is always a daunting task. It’s the breed of static and final methods and full of surprises. Technically intercepting mscorlib members is completely different from other class libraries. This is the reason it is dealt differently. Generally, I prefer writing a wrapper around an mscorlib member (Ex. File.Delete(“abc.txt”)) and expose it via interface but that is not always an easy task if you already have years old codebase. While mocking mscorlib members first thing that comes to people’s mind is DateTime.Now. If you Google through, you will find tons of example dealing with just that. May be it’s the most important class that we can’t ignore and I will create an example using JustMock Q2 with the same. In Q2 2012, we just get rid of the MockClassAtrribute for mocking mscorlib members. JustMock is already attribute free for mocking class libraries. We radically think that vendor specific attributes only makes your code smelly and therefore decided the same for mscorlib. Now, I want to fake DateTime.Now for the following class: public class NestedDateTime { public DateTime GetDateTime() { return DateTime.Now; } } It is the simplest one that can be. The first thing here is that I tell JustMock “hey we have a DateTime.Now in NestedDateTime class that we want to mock”. To do so, during the test initialization I write this: .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Mock.Replace(() => DateTime.Now).In<NestedDateTime>(x => x.GetDateTime());.csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } I can also define it for all the members in the class, but that’s just a waste of extra watts. Mock.Replace(() => DateTime.Now).In<NestedDateTime>(); Now question, why should I bother doing it? The answer is that I am not using attribute and with this approach, I can mock any framework members not just File, FileInfo or DateTime. Here to note that we already mock beyond the three but when nested around a complex class, JustMock was not intercepting it correctly. Therefore, we decided to get rid of the attribute altogether fixing the issue. Finally, I write my test as usual. [TestMethod] public void ShouldAssertMockingDateTimeFromNestedClass() { var expected = new DateTime(2000, 1, 1); Mock.Arrange(() => DateTime.Now).Returns(expected); Assert.Equal(new NestedDateTime().GetDateTime(), expected); } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } That’s it, we are good. Now let me do the same for a random one, let’s say I want mock a member from DriveInfo: Mock.Replace<DriveInfo[]>(() => DriveInfo.GetDrives()).In<MsCorlibFixture>(x => x.ShouldReturnExpectedDriveWhenMocked()); Moving forward, I write my test: [TestMethod] public void ShouldReturnExpectedDriveWhenMocked() { Mock.Arrange(() => DriveInfo.GetDrives()).MustBeCalled(); DriveInfo.GetDrives(); Mock.Assert(()=> DriveInfo.GetDrives()); } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Here is one convention; you have to replace the mscorlib member before executing the target method that contains it. Here the call to DriveInfo is within the MsCorlibFixture therefore it should be defined during test initialization or before executing the test method. Hope this gives you the idea.

    Read the article

  • Problem measuring N times the execution time of a code block

    - by Nazgulled
    EDIT: I just found my problem after writing this long post explaining every little detail... If someone can give me a good answer on what I'm doing wrong and how can I get the execution time in seconds (using a float with 5 decimal places or so), I'll mark that as accepted. Hint: The problem was on how I interpreted the clock_getttime() man page. Hi, Let's say I have a function named myOperation that I need to measure the execution time of. To measure it, I'm using clock_gettime() as it was recommend here in one of the comments. My teacher recommends us to measure it N times so we can get an average, standard deviation and median for the final report. He also recommends us to execute myOperation M times instead of just one. If myOperation is a very fast operation, measuring it M times allow us to get a sense of the "real time" it takes; cause the clock being used might not have the required precision to measure such operation. So, execution myOperation only one time or M times really depends if the operation itself takes long enough for the clock precision we are using. I'm having trouble dealing with that M times execution. Increasing M decreases (a lot) the final average value. Which doesn't make sense to me. It's like this, on average you take 3 to 5 seconds to travel from point A to B. But then you go from A to B and back to A 5 times (which makes it 10 times, cause A to B is the same as B to A) and you measure that. Than you divide by 10, the average you get is supposed to be the same average you take traveling from point A to B, which is 3 to 5 seconds. This is what I want my code to do, but it's not working. If I keep increasing the number of times I go from A to B and back A, the average will be lower and lower each time, it makes no sense to me. Enough theory, here's my code: #include <stdio.h> #include <time.h> #define MEASUREMENTS 1 #define OPERATIONS 1 typedef struct timespec TimeClock; TimeClock diffTimeClock(TimeClock start, TimeClock end) { TimeClock aux; if((end.tv_nsec - start.tv_nsec) < 0) { aux.tv_sec = end.tv_sec - start.tv_sec - 1; aux.tv_nsec = 1E9 + end.tv_nsec - start.tv_nsec; } else { aux.tv_sec = end.tv_sec - start.tv_sec; aux.tv_nsec = end.tv_nsec - start.tv_nsec; } return aux; } int main(void) { TimeClock sTime, eTime, dTime; int i, j; for(i = 0; i < MEASUREMENTS; i++) { printf(" » MEASURE %02d\n", i+1); clock_gettime(CLOCK_REALTIME, &sTime); for(j = 0; j < OPERATIONS; j++) { myOperation(); } clock_gettime(CLOCK_REALTIME, &eTime); dTime = diffTimeClock(sTime, eTime); printf(" - NSEC (TOTAL): %ld\n", dTime.tv_nsec); printf(" - NSEC (OP): %ld\n\n", dTime.tv_nsec / OPERATIONS); } return 0; } Notes: The above diffTimeClock function is from this blog post. I replaced my real operation with myOperation() because it doesn't make any sense to post my real functions as I would have to post long blocks of code, you can easily code a myOperation() with whatever you like to compile the code if you wish. As you can see, OPERATIONS = 1 and the results are: » MEASURE 01 - NSEC (TOTAL): 27456580 - NSEC (OP): 27456580 For OPERATIONS = 100 the results are: » MEASURE 01 - NSEC (TOTAL): 218929736 - NSEC (OP): 2189297 For OPERATIONS = 1000 the results are: » MEASURE 01 - NSEC (TOTAL): 862834890 - NSEC (OP): 862834 For OPERATIONS = 10000 the results are: » MEASURE 01 - NSEC (TOTAL): 574133641 - NSEC (OP): 57413 Now, I'm not a math wiz, far from it actually, but this doesn't make any sense to me whatsoever. I've already talked about this with a friend that's on this project with me and he also can't understand the differences. I don't understand why the value is getting lower and lower when I increase OPERATIONS. The operation itself should take the same time (on average of course, not the exact same time), no matter how many times I execute it. You could tell me that that actually depends on the operation itself, the data being read and that some data could already be in the cache and bla bla, but I don't think that's the problem. In my case, myOperation is reading 5000 lines of text from an CSV file, separating the values by ; and inserting those values into a data structure. For each iteration, I'm destroying the data structure and initializing it again. Now that I think of it, I also that think that there's a problem measuring time with clock_gettime(), maybe I'm not using it right. I mean, look at the last example, where OPERATIONS = 10000. The total time it took was 574133641ns, which would be roughly 0,5s; that's impossible, it took a couple of minutes as I couldn't stand looking at the screen waiting and went to eat something.

    Read the article

  • DataBinder Eval and Indexed properties

    - by erwin21
    As you probably know you can “Eval” an array property like below: <%# Eval("MyArray[0].Title") %> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }But what if your data object has indexed property? how do “Eval” that? Well it’s easier then you think it is: <%# Eval("[0]") %> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }And if your indexed property is based on for example a NameValueCollection you can “Eval” it like this: <%# Eval("[key]") %> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } As you see it’s very easy to “Eval” this kind of properties in you web application.

    Read the article

  • pagination for displaytag with colorbox in Spring framework

    - by Hitesh Solanki
    Hi..... I want to display the pop up for user selection using colorbox. I have put link on manageblacklist.jsp named 'select'. when I click on 'select' link ,colorbox is displayed. all user is displayed but pagination is not worked. I have used display tag for pagination. Without using colorbox, pagination is worked fine. I have used spring framework. The code of manageblacklist.jsp is given below: <%@ page contentType="text/html" pageEncoding="UTF-8" import="java.util.*"%> <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd"> <%@ include file="/WEB-INF/jsp/include.jsp" %> <%@ taglib prefix="form" uri="http://www.springframework.org/tags/form" %> <%@ taglib uri="http://displaytag.sf.net" prefix="display" %> <%@ page import="com.sufalam.mailserver.bean.User"%> <%@ page import="javax.servlet.http.HttpSession" %> <% String pageSize = (String) request.getAttribute("pageSize"); System.out.println("page size:" + pageSize); HttpSession session1 = request.getSession(); List<User> userList = (List<User>) session1.getAttribute("userList"); Iterator iterator = userList.iterator(); String user = (String) request.getAttribute("user"); System.out.println("user in the jsp :" + user); %> <html> <head> <script type="text/javascript" src="js/jquery142.js"></script> <script type="text/javascript" src="js/jquery.colorbox.js"></script> <link rel="stylesheet" href="style/colorbox.css" type="text/css"> <script type="text/javascript"> $(document).ready(function(){ //Examples of how to assign the ColorBox event to elements $(".example5").colorbox(); //Example of preserving a JavaScript event for inline calls. $("#click").click(function(){ $('#click').css({"background-color":"#f00", "color":"#fff", "cursor":"inherit"}).text("Open this window again and this message will still be here."); return false; }); }); </script> <script type="text/javascript"> function changePageSize() { var myValue = document.getElementById("combo1").value; document.getElementById("selectedPageSize").value=myValue; document.whitelistBlacklistForm.submit(); } function selectAll() { var selectAll = document.getElementById("checkAll"); var returnById = document.getElementsByName("check"); var i; var val; if (selectAll.checked == true) { val = true; } else { val = false; } for (i = 0; i < returnById.length; i++) { returnById[i].checked = val; } } function onload() { insertNavigation ('insertHereTop', 'insertHereBottom'); } function insertNavigation( topElementID, BottomElementID ) { if ( document.getElementById('pagingBanner') ){ document.getElementById(topElementID).innerHTML=document.getElementById('pagingBanner').innerHTML; document.getElementById(BottomElementID).innerHTML=document.getElementById('pagingBanner1').innerHTML; } } function confirmDelete() { if (confirm("Are you sure you want to delete selected records?")) { flag = 1; return true; } else { return false; } } function loadModels() { var flag=true; var textValue = document.getElementById('txtuser'); $.getJSON("ajaxblacklist.htm", // url { param :textValue.value }, // request params function(json) { // callback // var options = '<table class="displayTable" cellspacing="0"><thead><tr><th align = "center">Blacklisted Sender</th>'+ // '<th align ="center">Delete</th></tr></thead><tbody>'; var options = '<table width="100%" border="0" cellspacing="0" cellpadding="0"><tr><td style="background:url(images/leftbg.gif) repeat-y; width:8px;"></td>' + '<td class="middlesection"><table width="100%" border="0" cellspacing="0" cellpadding="0"><tr>' + '<td height="30" class="p10"><table width="100%" border="0" cellspacing="0" cellpadding="0" class="allboder" >' + '<tr><td class="tebelhd"> Blacklisted Sender </td></tr>'; for (i in json) { var state = json[i]; for(j in state){ var op = state[j]; if(op.length==undefined){ options += '<tr><td class="tdhd"><table width="0%" border="0" cellspacing="0" cellpadding="0"><tr><td width="741">'+ state[j].senderEmail + '</td><td align="center" width="148"><a href="managewhitelistblacklist.htm?sender='+state[j].senderEmail+'&recipient='+ state[j].recipientEmail+'&action=delete"><span> <img src="/MailServerV2/images/delete.gif"/> </span></a></td></tr></table></td></tr>'; break; } for(k in op) { if(flag == true) { flag = false; options += '<tr><td class="tdhd"><table width="0%" border="0" cellspacing="0" cellpadding="0"><tr>'; } else { flag = true; options += '<tr><td class="tdhd2"><table width="0%" border="0" cellspacing="0" cellpadding="0"><tr>'; } options += '<td width="741">'+ op[k].senderEmail +'</td><td align="center" width="148"><a href="managewhitelistblacklist.htm?sender='+op[k].senderEmail+'&recipient='+op[k].recipientEmail+'&action=delete"><span> <img src="/MailServerV2/images/delete.gif"/> </span></a></td></tr></table></td></tr>'; } } } options += '</td></tr></table>'; $("div[name^=blacklist]").html(options); }); } </script> </head> <body> <table width="" border="0" align="center" cellpadding="0" cellspacing="0" class="maintable"> <tr> <td class="topsection"><table width="100%" border="0" cellspacing="0" cellpadding="0"> <tr> <td valign="top" align="center" class="middlesection" ><table width="96%" border="0" cellspacing="0" cellpadding="0"> <tr> <td >&nbsp;</td> </tr> <tr> <td> <table width="100%" border="0" cellspacing ="0" cellpadding="0"> <tr> <td> <table width="100%" border="0" cellspacing="0" cellpadding="3"> <tr> <td align="left" valign="middle"><h1>Manage Blacklist</h1></td> <td align="right" valign="bottom"><div style="float:right;"><a href="savewhitelistblacklist.htm" class="buttonash"><span>Create Whitelist Blacklist </span></a></div></td> </tr> </table></td> </tr> <tr> <td class="bottomboder"><img src="images/ashish.gif" height="1" /></td> </tr> </table> </td> </tr> <tr> <td>&nbsp;</td> </tr> <tr> <td> </td> </tr> <tr> <td> <div id="TabbedPanels1" class="TabbedPanels"/> <div style="display: block;" class="TabbedPanelsContent"/> <div align="left" class="tebelhd"> Blacklist Information </div><div class="entry-edit"> <div class="fieldset" id="base_fieldset"> <div class="hor-scroll_1" align="left"> <fieldset Class="label1css" style="color:#666666"> <legend>Fields</legend> <table> <tr> <td align="right"> Recipient Email : </td> <td><input type="text" id="txtuser" name="txtuser" <% if (user != null) { %> value="<%=user%>" <% } else { %> value="" <% } %> /> </td> <td><a href="#" class="buttonash" onclick="loadModels()"><span>Search</span></a></td> <!-- <td><a href="javascript:void(0)" class="buttonash" onclick="window.open('selectuser.htm','selectuser','width=600,height=400,menubar=yes,status=yes,location=yes,toolbar=yes,scrollbars=yes');" ><span>Select</span></a></td>--> <td><a href="selectuser.htm" class="example5 buttonash" ><span>Select</span></a> </td> <td align="right"> </td> </tr> </table> </fieldset> <div id="blacklist" name="blacklist"></div> </div> </div> </div> </td> </tr> </table> </td> </tr> </table> </td> <!-- InstanceEndEditable --> <td style="background:url(images/rightbg.gif) repeat-y; width:8px;"></td> </tr> </table> <% // session1.removeAttribute("user"); %> </body> </html> So , please tell me how to work pagination .... Thanks in advanced...

    Read the article

  • Lua Alien Module - Trouble using WriteProcessMemory function, unsure on types (unit32)

    - by jefferysanders
    require "alien" --the address im trying to edit in the Mahjong game on Win7 local SCOREREF = 0x0744D554 --this should give me full access to the process local ACCESS = 0x001F0FFF --this is my process ID for my open window of Mahjong local PID = 1136 --function to open proc local op = alien.Kernel32.OpenProcess op:types{ ret = "pointer", abi = "stdcall"; "int", "int", "int"} --function to write to proc mem local wm = alien.Kernel32.WriteProcessMemory wm:types{ ret = "long", abi = "stdcall"; "pointer", "pointer", "pointer", "long", "pointer" } local pRef = op(ACCESS, true, PID) local buf = alien.buffer("99") -- ptr,uint32,byte arr (no idea what to make this),int, ptr print( wm( pRef, SCOREREF, buf, 4, nil)) --prints 1 if success, 0 if failed So that is my code. I am not even sure if I have the types set correctly. I am completely lost and need some guidance. I really wish there was more online help/documentation for alien, it confuses my poor brain. What utterly baffles me is that it WriteProcessMemory will sometimes complete successfully (though it does nothing at all, to my knowledge) and will also sometimes fail to complete successfully. As I've stated, my brain hurts. Any help appreciated.

    Read the article

  • JBoss: What does the warning EJBTHREE-1246 from the InterceptorRegistry mean?

    - by Simon Lehmann
    I am currently developing an EJB 3.0 based application on the JBoss AS 5.0.0.GA and just recently the following warning showed up in the server log: 09:50:19,735 WARN [InterceptorsFactory] EJBTHREE-1246: Do not use InterceptorsFactory with a ManagedObjectAdvisor, InterceptorRegistry should be used via the bean container 09:50:19,735 WARN [InterceptorsFactory] EJBTHREE-1246: Do not use InterceptorsFactory with a ManagedObjectAdvisor, InterceptorRegistry should be used via the bean container 09:50:19,735 WARN [InterceptorRegistry] applicable interceptors is non-existent for ... ... The warnings are generated as soon as an EJB (a stateless session bean) is injected into a backing bean of my JSF web-application. The beans do work without problems though, but I still would like to know where that warning comes from and what I can do to avoid it. I have already searched a bit around, but haven't found a good answer (some say, bean developers do not have to worry, but its a warning, so I'd like to have a better solution): http://www.jboss.com/index.html?module=bb&op=viewtopic&t=147292 http://www.jboss.com/index.html?module=bb&op=viewtopic&p=4180366 http://www.jboss.com/index.html?module=bb&op=viewtopic&p=4140136 JBoss JIRA Issue about the warning (Not that helpful in my opinion) So has anyone an explanation what causes the warning (in terms of a bean developer, not application server developer) and what to do to avoid it? Update: I've just upgraded JBoss to 5.0.1.GA (Download, Release-Notes) but unfortunatly the warning still appears.

    Read the article

  • BasicDBObject or QueryBuilder and some newbie questions of Java and mongo

    - by Kevin Xu
    hi I'm a fresh newbie to mongodb Q1 using query=new BasicDBObject(); query.put("i", new BasicDBObject("$gt",13)); and query=new QueryBuilder().put("i").Greaterthan(13).get() is there any difference inside of the system? Q2 I've created a class class findkv extends BasicDBObject{ //is gt gte lt lte public findkv(String fieldname,String op,Object tvalue) { if (op=="") this.put(fieldname,tvalue); else this.put(fieldname, new BasicDBObject(op,tvalue)); } } shall I use it or shall I just use original function? Q3 I've used mongo shell for a few weeks, and was customed to it, and find writing in mongo shell faster and shorter, which side has more advantage, writing in mongo or in java? I shall dump them from mongo to mysql Q4 I've an if (statement==true) return else dowhat; seems can't be compiled I know I can write if (statement!=true) dowhat else return, but can I still write in first style? q5 my eclipse is Eclipse Java EE IDE for Web Developers. Version: Juno Release Build id: 20120614-1722 I'd like to install Perl which I haven't learned yet I choose Install Update http://e-p-i-c.sf.net/updates/testing but it doesn't work, any method to install perl to eclipse manually?

    Read the article

  • cant open device

    - by yoavstr
    I have a little problem. I install this module into my kernel and its written under /proc When I try to open() it from user mode I get the following message: "Can't open device file: my_dev" static int module_permission(struct inode *inode, int op, struct nameidata *foo) { //if its write if ((op == 2)&&(writer == DOESNT_EXIST)){ writer = EXIST ; return 0; } //if its read if (op == 4 ){ numOfReaders++; return 0; } return -EACCES; } int procfs_open(struct inode *inode, struct file *file) { try_module_get(THIS_MODULE); return 0; } static struct file_operations File_Ops_4_Our_Proc_File = { .read = procfs_read, .write = procfs_write, .open = procfs_open, .release = procfs_close, }; static struct inode_operations Inode_Ops_4_Our_Proc_File = { .permission = module_permission, /* check for permissions */ }; int init_module() { /* create the /proc file */ Our_Proc_File = create_proc_entry(PROC_ENTRY_FILENAME, 0644, NULL); /* check if the /proc file was created successfuly */ if (Our_Proc_File == NULL){ printk(KERN_ALERT "Error: Could not initialize /proc/%s\n", PROC_ENTRY_FILENAME); return -ENOMEM; } Our_Proc_File->owner = THIS_MODULE; Our_Proc_File->proc_iops = &Inode_Ops_4_Our_Proc_File; Our_Proc_File->proc_fops = &File_Ops_4_Our_Proc_File; Our_Proc_File->mode = S_IFREG | S_IRUGO | S_IWUSR; Our_Proc_File->uid = 0; Our_Proc_File->gid = 0; Our_Proc_File->size = 80; //i added init the writewr status writer = DOESNT_EXIST; numOfReaders = 0 ; printk(KERN_INFO "/proc/%s created\n", PROC_ENTRY_FILENAME); return 0; }

    Read the article

  • Getting an non-object error in my php script

    - by Disowned
    Hey I was trying to call a script to made some changes to an html file, however when I run the script it tells me that it's making a call to a non-object. Obviously I did something wrong, but what? Here's the script. /*Dom controllers*/ $dom = new DOMDocument(); $dom->loadHTML('index.html'); $id = $dom->getElementById('contact_us'); $p = $dom->appendChild(new DOMElement('p')); $op = $dom->getElementsByTagName('p'); /* Dem POST vars used by dat Ajax mah ziggen, yeah boi*/ if (isset($_POST['Home']) && isset($_POST['About']) && isset($_POST['Contact']) && isset($_POST['sexyText'])){ $home = $_POST['Home']; $about = $_POST['About']; $contact = $_POST['Contact']; $text = $_POST['sexyText']; trim($home); trim($about); trim($contact); trim($text); } function post(){ global $dom, $id, $home, $about, $contact, $text, $textp, $p, $op; $textp = $dom->createTextNode($text); $p->appendChild($textp); $id->replaceChild($p, $op); $dom->saveHTMLFile('index.html'); } post(); echo 1; ?> The error happens at the replaceChild function.

    Read the article

  • Java extends classes - Share the extended class fields within the super class.

    - by Bastan
    Straight to the point... I have a class public class P_Gen{ protected String s; protected Object oP_Gen; public P_Gen(String str){ s = str; oP_Gen = new Myclass(this); } } Extended class: public class P extends P_Gen{ protected Object oP; public P(String str){ oP = new aClass(str); super(str); } } MyClass: public class MyClass{ protected Object oMC; public MyClass(P extendedObject){ oMc = oP.getSomething(); } } I came to realize that MyClass can only be instantiated with (P_Gen thisObject) as opposed to (P extendedObject). The situation is that I have code generated a bunch of classes like P_Gen. For each of them I have generated a class P which would contains my P specific custom methods and fields. When I'll regenerate my code in the future, P would not be overwritten as P_Gen would. ** So what happened in my case???!!!... I realized that MyClass would beneficiate from the info stored in P in addition to only P_Gen. Would that possible? I know it's not JAVA "realistic" since another class that extends P_Gen might not have the same fields... BY DESIGN, P_Gen will not be extended by anything but P.... And that's where it kinda make sens. :-) at least in other programming language ;-) In other programming language, it seems like P_Gen.this === P.this, in other word, "this" becomes a combination of P and P_Gen. Is there a way to achieve this knowing that P_Gen won't be extended by anything than P?

    Read the article

  • csv file upload and update mysql db

    - by Indra
    I am very to new to php. i am using the following code to open a csv file and update my database. i need to check the value of first row-first column of the csv file. if it is matching "some text 1", then i need to run code1, if it is "some text 2", run code2, else code3. I can use if else condition but since i am using while loop It fails. Can anyone help me. $handle = fopen($file_tmp,"r"); while(($fileop = fgetcsv($handle,",")) !== false) { // I need to check here $companycode = mysql_real_escape_string($fileop[0]); $Item = mysql_real_escape_string($fileop[3]); $pack = preg_replace('/[^A-Za-z0-9\. -]/', '', $fileop[4]); $lastmonth = mysql_real_escape_string($fileop[5]); $ltlmonth = mysql_real_escape_string($fileop[6]); $op = mysql_real_escape_string($fileop[9]); $pur = mysql_real_escape_string($fileop[10]); $sale = mysql_real_escape_string($fileop[12]); $bal = mysql_real_escape_string($fileop[17]); $bval = mysql_real_escape_string($fileop[18]); $sval = mysql_real_escape_string($fileop[19]); $sq1 = mysql_query("INSERT INTO `sas` (companycode,Item,pack,lastmonth,ltlmonth,op,pur,sale,bal,bval,sval) VALUES ('$companycode','$Item','$pack','$lastmonth','$ltlmonth','$op','$pur','$sale','$bal','$bval','$sval')"); }

    Read the article

  • why i change the alpha value of UIImageView but no effect?

    - by chancy
    I am working on a reader app. when you read one magazine, it will display first five pages and download the rest pages one by one. there is a scrollview to view the thumbnail image of pages. At the beginning, if the page needs downloading, the corresponding thumbnail view's alpha value is set to 0.5. when the page is downloaded, i will update the thumbnail view's value to 1.0. I use one operation to download the page, and when one is downloaded i use delegate to set thumbnail view's alpha. But when i update thumbnail view's alpha value, it still the same as the beginning. it seems the alpha has no effect. I wonder is there anything wrong with my code? some snippets are as follows: In the PageViewController.m - (void)downloadPages { DownloadOperation *op = [[DownloadOperation alloc] initWithMagazine:magazine]; op.delegate = self; [[(AppDelegate *)[[UIApplication sharedApplication] delegate] sharedOperationQueue] addOperation:op]; } - (void)downloadOperation:(DownloadOperation *)operation finishedAtIndex:(NSUInteger)index { if (thumbScrollView){ [thumbScrollView viewWithTag:THUMBVIEW_OFFSET+index].alpha = 1.0; } } In DownloadOperation.m - (void)main { // ... NSUInteger index = 0; for (Page *page in mMagazine.pages) { if (/*page doesn't exist*/){ // download the page; if ([delegate respondsToSelector:@selector(downloadOperation:finishedAtIndex:)]) { [delegate downloadOperation:self finishedAtIndex:index]; } } index++; } }

    Read the article

  • AuthnRequest Settings in OIF / SP

    - by Damien Carru
    In this article, I will list the various OIF/SP settings that affect how an AuthnRequest message is created in OIF in a Federation SSO flow. The AuthnRequest message is used by an SP to start a Federation SSO operation and to indicate to the IdP how the operation should be executed: How the user should be challenged at the IdP Whether or not the user should be challenged at the IdP, even if a session already exists at the IdP for this user Which NameID format should be requested in the SAML Assertion Which binding (Artifact or HTTP-POST) should be requested from the IdP to send the Assertion Which profile should be used by OIF/SP to send the AuthnRequest message Enjoy the reading! Protocols The SAML 2.0, SAML 1.1 and OpenID 2.0 protocols define different message elements and rules that allow an administrator to influence the Federation SSO flows in different manners, when the SP triggers an SSO operation: SAML 2.0 allows extensive customization via the AuthnRequest message SAML 1.1 does not allow any customization, since the specifications do not define an authentication request message OpenID 2.0 allows for some customization, mainly via the OpenID 2.0 extensions such as PAPE or UI SAML 2.0 OIF/SP allows the customization of the SAML 2.0 AuthnRequest message for the following elements: ForceAuthn: Boolean indicating whether or not the IdP should force the user for re-authentication, even if the user has still a valid session By default set to false IsPassive Boolean indicating whether or not the IdP is allowed to interact with the user as part of the Federation SSO operation. If false, the Federation SSO operation might result in a failure with the NoPassive error code, because the IdP will not have been able to identify the user By default set to false RequestedAuthnContext Element indicating how the user should be challenged at the IdP If the SP requests a Federation Authentication Method unknown to the IdP or for which the IdP is not configured, then the Federation SSO flow will result in a failure with the NoAuthnContext error code By default missing NameIDPolicy Element indicating which NameID format the IdP should include in the SAML Assertion If the SP requests a NameID format unknown to the IdP or for which the IdP is not configured, then the Federation SSO flow will result in a failure with the InvalidNameIDPolicy error code If missing, the IdP will generally use the default NameID format configured for this SP partner at the IdP By default missing ProtocolBinding Element indicating which SAML binding should be used by the IdP to redirect the user to the SP with the SAML Assertion Set to Artifact or HTTP-POST By default set to HTTP-POST OIF/SP also allows the administrator to configure the server to: Set which binding should be used by OIF/SP to redirect the user to the IdP with the SAML 2.0 AuthnRequest message: Redirect or HTTP-POST By default set to Redirect Set which binding should be used by OIF/SP to redirect the user to the IdP during logout with SAML 2.0 Logout messages: Redirect or HTTP-POST By default set to Redirect SAML 1.1 The SAML 1.1 specifications do not define a message for the SP to send to the IdP when a Federation SSO operation is started. As such, there is no capability to configure OIF/SP on how to affect the start of the Federation SSO flow. OpenID 2.0 OpenID 2.0 defines several extensions that can be used by the SP/RP to affect how the Federation SSO operation will take place: OpenID request: mode: String indicating if the IdP/OP can visually interact with the user checkid_immediate does not allow the IdP/OP to interact with the user checkid_setup allows user interaction By default set to checkid_setup PAPE Extension: max_auth_age : Integer indicating in seconds the maximum amount of time since when the user authenticated at the IdP. If MaxAuthnAge is bigger that the time since when the user last authenticated at the IdP, then the user must be re-challenged. OIF/SP will set this attribute to 0 if the administrator configured ForceAuthn to true, otherwise this attribute won't be set Default missing preferred_auth_policies Contains a Federation Authentication Method Element indicating how the user should be challenged at the IdP By default missing Only specified in the OpenID request if the IdP/OP supports PAPE in XRDS, if OpenID discovery is used. UI Extension Popup mode Boolean indicating the popup mode is enabled for the Federation SSO By default missing Language Preference String containing the preferred language, set based on the browser's language preferences. By default missing Icon: Boolean indicating if the icon feature is enabled. In that case, the IdP/OP would look at the SP/RP XRDS to determine how to retrieve the icon By default missing Only specified in the OpenID request if the IdP/OP supports UI Extenstion in XRDS, if OpenID discovery is used. ForceAuthn and IsPassive WLST Command OIF/SP provides the WLST configureIdPAuthnRequest() command to set: ForceAuthn as a boolean: In a SAML 2.0 AuthnRequest, the ForceAuthn field will be set to true or false In an OpenID 2.0 request, if ForceAuthn in the configuration was set to true, then the max_auth_age field of the PAPE request will be set to 0, otherwise, max_auth_age won't be set IsPassive as a boolean: In a SAML 2.0 AuthnRequest, the IsPassive field will be set to true or false In an OpenID 2.0 request, if IsPassive in the configuration was set to true, then the mode field of the OpenID request will be set to checkid_immediate, otherwise set to checkid_setup Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> Let's configure OIF/SP for that IdP Partner, so that the SP will require the IdP to re-challenge the user, even if the user is already authenticated: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the configureIdPAuthnRequest() command:configureIdPAuthnRequest(partner="AcmeIdP", forceAuthn="true") Exit the WLST environment:exit() After the changes, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ForceAuthn="true" ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> To display or delete the ForceAuthn/IsPassive settings, perform the following operatons: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the configureIdPAuthnRequest() command: To display the ForceAuthn/IsPassive settings on the partnerconfigureIdPAuthnRequest(partner="AcmeIdP", displayOnly="true") To delete the ForceAuthn/IsPassive settings from the partnerconfigureIdPAuthnRequest(partner="AcmeIdP", delete="true") Exit the WLST environment:exit() Requested Fed Authn Method In my earlier "Fed Authentication Method Requests in OIF / SP" article, I discussed how OIF/SP could be configured to request a specific Federation Authentication Method from the IdP when starting a Federation SSO operation, by setting elements in the SSO request message. WLST Command The OIF WLST commands that can be used are: setIdPPartnerProfileRequestAuthnMethod() which will configure the requested Federation Authentication Method in a specific IdP Partner Profile, and accepts the following parameters: partnerProfile: name of the IdP Partner Profile authnMethod: the Federation Authentication Method to request displayOnly: an optional parameter indicating if the method should display the current requested Federation Authentication Method instead of setting it delete: an optional parameter indicating if the method should delete the current requested Federation Authentication Method instead of setting it setIdPPartnerRequestAuthnMethod() which will configure the specified IdP Partner entry with the requested Federation Authentication Method, and accepts the following parameters: partner: name of the IdP Partner authnMethod: the Federation Authentication Method to request displayOnly: an optional parameter indicating if the method should display the current requested Federation Authentication Method instead of setting it delete: an optional parameter indicating if the method should delete the current requested Federation Authentication Method instead of setting it This applies to SAML 2.0 and OpenID 2.0 protocols. See the "Fed Authentication Method Requests in OIF / SP" article for more information. Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> Let's configure OIF/SP for that IdP Partner, so that the SP will request the IdP to use a mechanism mapped to the urn:oasis:names:tc:SAML:2.0:ac:classes:X509 Federation Authentication Method to authenticate the user: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setIdPPartnerRequestAuthnMethod() command:setIdPPartnerRequestAuthnMethod("AcmeIdP", "urn:oasis:names:tc:SAML:2.0:ac:classes:X509") Exit the WLST environment:exit() After the changes, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/>   <samlp:RequestedAuthnContext Comparison="minimum">      <saml:AuthnContextClassRef xmlns:saml="urn:oasis:names:tc:SAML:2.0:assertion">         urn:oasis:names:tc:SAML:2.0:ac:classes:X509      </saml:AuthnContextClassRef>   </samlp:RequestedAuthnContext></samlp:AuthnRequest> NameID Format The SAML 2.0 protocol allows for the SP to request from the IdP a specific NameID format to be used when the Assertion is issued by the IdP. Note: SAML 1.1 and OpenID 2.0 do not provide such a mechanism Configuring OIF The administrator can configure OIF/SP to request a NameID format in the SAML 2.0 AuthnRequest via: The OAM Administration Console, in the IdP Partner entry The OIF WLST setIdPPartnerNameIDFormat() command that will modify the IdP Partner configuration OAM Administration Console To configure the requested NameID format via the OAM Administration Console, perform the following steps: Go to the OAM Administration Console: http(s)://oam-admin-host:oam-admin-port/oamconsole Navigate to Identity Federation -> Service Provider Administration Open the IdP Partner you wish to modify In the Authentication Request NameID Format dropdown box with one of the values None The NameID format will be set Default Email Address The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:emailAddress X.509 Subject The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:X509SubjectName Windows Name Qualifier The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:WindowsDomainQualifiedName Kerberos The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:kerberos Transient The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:transient Unspecified The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:unspecified Custom In this case, a field would appear allowing the administrator to indicate the custom NameID format to use The NameID format will be set to the specified format Persistent The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:persistent I selected Email Address in this example Save WLST Command To configure the requested NameID format via the OIF WLST setIdPPartnerNameIDFormat() command, perform the following steps: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the setIdPPartnerNameIDFormat() command:setIdPPartnerNameIDFormat("PARTNER", "FORMAT", customFormat="CUSTOM") Replace PARTNER with the IdP Partner name Replace FORMAT with one of the following: orafed-none The NameID format will be set Default orafed-emailaddress The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:emailAddress orafed-x509 The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:X509SubjectName orafed-windowsnamequalifier The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:WindowsDomainQualifiedName orafed-kerberos The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:kerberos orafed-transient The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:transient orafed-unspecified The NameID format will be set urn:oasis:names:tc:SAML:1.1:nameid-format:unspecified orafed-custom In this case, a field would appear allowing the administrator to indicate the custom NameID format to use The NameID format will be set to the specified format orafed-persistent The NameID format will be set urn:oasis:names:tc:SAML:2.0:nameid-format:persistent customFormat will need to be set if the FORMAT is set to orafed-custom An example would be:setIdPPartnerNameIDFormat("AcmeIdP", "orafed-emailaddress") Exit the WLST environment:exit() Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer> <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> After the changes performed either via the OAM Administration Console or via the OIF WLST setIdPPartnerNameIDFormat() command where Email Address would be requested as the NameID Format, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ForceAuthn="false" IsPassive="false" ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer> <samlp:NameIDPolicy Format="urn:oasis:names:tc:SAML:1.1:nameid-format:emailAddress" AllowCreate="true"/></samlp:AuthnRequest> Protocol Binding The SAML 2.0 specifications define a way for the SP to request which binding should be used by the IdP to redirect the user to the SP with the SAML 2.0 Assertion: the ProtocolBinding attribute indicates the binding the IdP should use. It is set to: Either urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST for HTTP-POST Or urn:oasis:names:tc:SAML:2.0:bindings:Artifact for Artifact The SAML 2.0 specifications also define different ways to redirect the user from the SP to the IdP with the SAML 2.0 AuthnRequest message, as the SP can send the message: Either via HTTP Redirect Or HTTP POST (Other bindings can theoretically be used such as Artifact, but these are not used in practice) Configuring OIF OIF can be configured: Via the OAM Administration Console or the OIF WLST configureSAMLBinding() command to set the Assertion Response binding to be used Via the OIF WLST configureSAMLBinding() command to indicate how the SAML AuthnRequest message should be sent Note: the binding for sending the SAML 2.0 AuthnRequest message will also be used to send the SAML 2.0 LogoutRequest and LogoutResponse messages. OAM Administration Console To configure the SSO Response/Assertion Binding via the OAM Administration Console, perform the following steps: Go to the OAM Administration Console: http(s)://oam-admin-host:oam-admin-port/oamconsole Navigate to Identity Federation -> Service Provider Administration Open the IdP Partner you wish to modify Check the "HTTP POST SSO Response Binding" box to request the IdP to return the SSO Response via HTTP POST, otherwise uncheck it to request artifact Save WLST Command To configure the SSO Response/Assertion Binding as well as the AuthnRequest Binding via the OIF WLST configureSAMLBinding() command, perform the following steps: Enter the WLST environment by executing:$IAM_ORACLE_HOME/common/bin/wlst.sh Connect to the WLS Admin server:connect() Navigate to the Domain Runtime branch:domainRuntime() Execute the configureSAMLBinding() command:configureSAMLBinding("PARTNER", "PARTNER_TYPE", binding, ssoResponseBinding="httppost") Replace PARTNER with the Partner name Replace PARTNER_TYPE with the Partner type (idp or sp) Replace binding with the binding to be used to send the AuthnRequest and LogoutRequest/LogoutResponse messages (should be httpredirect in most case; default) httppost for HTTP-POST binding httpredirect for HTTP-Redirect binding Specify optionally ssoResponseBinding to indicate how the SSO Assertion should be sent back httppost for HTTP-POST binding artifactfor for Artifact binding An example would be:configureSAMLBinding("AcmeIdP", "idp", "httpredirect", ssoResponseBinding="httppost") Exit the WLST environment:exit() Test In this test, OIF/SP is integrated with a remote SAML 2.0 IdP Partner, with the OOTB configuration which requests HTTP-POST from the IdP to send the SSO Assertion. Based on this setup, when OIF/SP starts a Federation SSO flow, the following SAML 2.0 AuthnRequest would be generated: <samlp:AuthnRequest ProtocolBinding="urn:oasis:names:tc:SAML:2.0:bindings:HTTP-POST" ID="id-E4BOT7lwbYK56lO57dBaqGUFq01WJSjAHiSR60Q4" Version="2.0" IssueInstant="2014-04-01T21:39:14Z" Destination="https://acme.com/saml20/sso">   <saml:Issuer Format="urn:oasis:names:tc:SAML:2.0:nameid-format:entity">https://sp.com/oam/fed</saml:Issuer>   <samlp:NameIDPolicy AllowCreate="true"/></samlp:AuthnRequest> In the next article, I will cover the various crypto configuration properties in OIF that are used to affect the Federation SSO exchanges.Cheers,Damien Carru

    Read the article

  • Preventing duplicate Data with ASP.NET AJAX

    - by Yousef_Jadallah
      Some times you need to prevent  User names ,E-mail ID's or other values from being duplicated by a new user during Registration or any other cases,So I will add a simple approach to make the page more user-friendly. Instead the user filled all the Registration fields then press submit after that received a message as a result of PostBack that "THIS USERNAME IS EXIST", Ajax tidies this up by allowing asynchronous querying while the user is still completing the registration form.   ASP.NET enables you to create Web services can be accessed from client script in Web pages by using AJAX technology to make Web service calls. Data is exchanged asynchronously between client and server, typically in JSON format. I’ve added an article to show you step by step  how to use ASP.NET AJAX with Web Services , you can find it here .   Lets go a head with the steps :   1-Create a new project , if you are using VS 2005 you have to create ASP.NET Ajax Enabled Web site.   2-Create your own Database which contain user table that have User_Name field. for Testing I’ve added SQL Server Database that come with Dot Net 2008: Then I’ve created tblUsers:   This table and this structure just for our example, you can use your own table to implement this approach.   3-Add new Item to your project or website, Choose Web Service file, lets say  WebService.cs  .In this Web Service file import System.Data.SqlClient Namespace, Then Add your web method that contain string parameter which received the Username parameter from the Script , Finally don’t forget to qualified the Web Service Class with the ScriptServiceAttribute attribute ([System.Web.Script.Services.ScriptService])     using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.Services; using System.Data.SqlClient;     [WebService(Namespace = "http://tempuri.org/")] [WebServiceBinding(ConformsTo = WsiProfiles.BasicProfile1_1)] [System.Web.Script.Services.ScriptService] public class WebService : System.Web.Services.WebService {     [WebMethod] public int CheckDuplicate(string User_Name) { string strConn = @"Data Source=.\SQLEXPRESS;AttachDbFilename=|DataDirectory|\TestDB.mdf;Integrated Security=True;User Instance=True"; string strQuery = "SELECT COUNT(*) FROM tblUsers WHERE User_Name = @User_Name"; SqlConnection con = new SqlConnection(strConn); SqlCommand cmd = new SqlCommand(strQuery, con); cmd.Parameters.Add("User_Name", User_Name); con.Open(); int RetVal= (int)cmd.ExecuteScalar(); con.Close(); return RetVal; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   Our Web Method here is CheckDuplicate Which accept User_Name String as a parameter and return number of the rows , if the name will found in the database this method will return 1 else it will return 0. I’ve applied  [WebMethod] Attribute to our method CheckDuplicate, And applied the ScriptService attribute to a Web Service class named WebService.   4-Add this simple Registration form : <fieldset> <table id="TblRegistratoin" cellpadding="0" cellspacing="0"> <tr> <td> User Name </td> <td> <asp:TextBox ID="txtUserName" onblur="CallWebMethod();" runat="server"></asp:TextBox> </td> <td> <asp:Label ID="lblDuplicate" runat="server" ForeColor="Red" Text=""></asp:Label> </td> </tr> <tr> <td colspan="3"> <asp:Button ID="btnRegistration" runat="server" Text="Registration" /> </td> </tr> </table> </fieldset> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   onblur event is added to the Textbox txtUserName, This event Fires when the Textbox loses the input focus, That mean after the user get focus out from the Textbox CallWebMethod function will be fired. CallWebMethod will be implemented in step 6.   5-Add ScriptManager Control to your aspx file then reference the Web service by adding an asp:ServiceReference child element to the ScriptManager control and setting its path attribute to point to the Web service, That generate a JavaScript proxy class for calling the specified Web service from client script.   <asp:ScriptManager runat="server" ID="scriptManager"> <Services> <asp:ServiceReference Path="WebService.asmx" /> </Services> </asp:ScriptManager> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }     6-Define the JavaScript code to call the Web Service :   <script language="javascript" type="text/javascript">   // This function calls the Web service method // passing simple type parameters and the // callback function function CallWebMethod() { var User_Name = document.getElementById('<%=txtUserName.ClientID %>').value; WebService.CheckDuplicate(User_Name, OnSucceeded, OnError); }   // This is the callback function invoked if the Web service // succeeded function OnSucceeded(result) { var rsltElement = document.getElementById("lblDuplicate"); if (result == 1) rsltElement.innerHTML = "This User Name is exist"; else rsltElement.innerHTML = "";   }   function OnError(error) { // Display the error. alert("Service Error: " + error.get_message()); } </script> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   This call references the WebService Class and CheckDuplicate Web Method defined in the service. It passes a User_Name value obtained from a textbox as well as a callback function named OnSucceeded that should be invoked when the asynchronous Web Service call returns. If the Web Service in different Namespace you can refer it before the class name this Main formula may help you :  NameSpaceName.ClassName.WebMethdName(Parameters , Success callback function, Error callback function); Parameters: you can pass one or many parameters. Success callback function :handles returned data from the service . Error callback function :Any errors that occur when the Web Service is called will trigger in this function. Using Error Callback function is optional.   Hope these steps help you to understand this approach.

    Read the article

  • Preventing duplicate Data with ASP.NET AJAX

    - by Yousef_Jadallah
      Some times you need to prevent  User names ,E-mail ID's or other values from being duplicated by a new user during Registration or any other cases,So I will add a simple approach to make the page more user-friendly. Instead the user filled all the Registration fields then press submit after that received a message as a result of PostBack that "THIS USERNAME IS EXIST", Ajax tidies this up by allowing asynchronous querying while the user is still completing the registration form.   ASP.NET enables you to create Web services can be accessed from client script in Web pages by using AJAX technology to make Web service calls. Data is exchanged asynchronously between client and server, typically in JSON format. I’ve added an article to show you step by step  how to use ASP.NET AJAX with Web Services , you can find it here .   Lets go a head with the steps :   1-Create a new project , if you are using VS 2005 you have to create ASP.NET Ajax Enabled Web site.   2-Create your own Database which contain user table that have User_Name field. for Testing I’ve added SQL Server Database that come with Dot Net 2008: Then I’ve created tblUsers:   This table and this structure just for our example, you can use your own table to implement this approach.   3-Add new Item to your project or website, Choose Web Service file, lets say  WebService.cs  .In this Web Service file import System.Data.SqlClient Namespace, Then Add your web method that contain string parameter which received the Username parameter from the Script , Finally don’t forget to qualified the Web Service Class with the ScriptServiceAttribute attribute ([System.Web.Script.Services.ScriptService])     using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.Services; using System.Data.SqlClient;     [WebService(Namespace = "http://tempuri.org/")] [WebServiceBinding(ConformsTo = WsiProfiles.BasicProfile1_1)] [System.Web.Script.Services.ScriptService] public class WebService : System.Web.Services.WebService {     [WebMethod] public int CheckDuplicate(string User_Name) { string strConn = @"Data Source=.\SQLEXPRESS;AttachDbFilename=|DataDirectory|\TestDB.mdf;Integrated Security=True;User Instance=True"; string strQuery = "SELECT COUNT(*) FROM tblUsers WHERE User_Name = @User_Name"; SqlConnection con = new SqlConnection(strConn); SqlCommand cmd = new SqlCommand(strQuery, con); cmd.Parameters.Add("User_Name", User_Name); con.Open(); int RetVal= (int)cmd.ExecuteScalar(); con.Close(); return RetVal; } } .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   Our Web Method here is CheckDuplicate Which accept User_Name String as a parameter and return number of the rows , if the name will found in the database this method will return 1 else it will return 0. I’ve applied  [WebMethod] Attribute to our method CheckDuplicate, And applied the ScriptService attribute to a Web Service class named WebService.   4-Add this simple Registration form : <fieldset> <table id="TblRegistratoin" cellpadding="0" cellspacing="0"> <tr> <td> User Name </td> <td> <asp:TextBox ID="txtUserName" onblur="CallWebMethod();" runat="server"></asp:TextBox> </td> <td> <asp:Label ID="lblDuplicate" runat="server" ForeColor="Red" Text=""></asp:Label> </td> </tr> <tr> <td colspan="3"> <asp:Button ID="btnRegistration" runat="server" Text="Registration" /> </td> </tr> </table> </fieldset> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   onblur event is added to the Textbox txtUserName, This event Fires when the Textbox loses the input focus, That mean after the user get focus out from the Textbox CallWebMethod function will be fired. CallWebMethod will be implemented in step 6.   5-Add ScriptManager Control to your aspx file then reference the Web service by adding an asp:ServiceReference child element to the ScriptManager control and setting its path attribute to point to the Web service, That generate a JavaScript proxy class for calling the specified Web service from client script.   <asp:ScriptManager runat="server" ID="scriptManager"> <Services> <asp:ServiceReference Path="WebService.asmx" /> </Services> </asp:ScriptManager> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }     6-Define the JavaScript code to call the Web Service :   <script language="javascript" type="text/javascript">   // This function calls the Web service method // passing simple type parameters and the // callback function function CallWebMethod() { var User_Name = document.getElementById('<%=txtUserName.ClientID %>').value; WebService.CheckDuplicate(User_Name, OnSucceeded, OnError); }   // This is the callback function invoked if the Web service // succeeded function OnSucceeded(result) { var rsltElement = document.getElementById("lblDuplicate"); if (result == 1) rsltElement.innerHTML = "This User Name is exist"; else rsltElement.innerHTML = "";   }   function OnError(error) { // Display the error. alert("Service Error: " + error.get_message()); } </script> .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; }   This call references the WebService Class and CheckDuplicate Web Method defined in the service. It passes a User_Name value obtained from a textbox as well as a callback function named OnSucceeded that should be invoked when the asynchronous Web Service call returns. If the Web Service in different Namespace you can refer it before the class name this Main formula may help you :  NameSpaceName.ClassName.WebMethdName(Parameters , Success callback function, Error callback function); Parameters: you can pass one or many parameters. Success callback function :handles returned data from the service . Error callback function :Any errors that occur when the Web Service is called will trigger in this function. Using Error Callback function is optional.   Hope these steps help you to understand this approach.

    Read the article

  • Configuring OpenLDAP as a Active Directory Proxy

    - by vadensumbra
    We try to set up an Active Directory server for company-wide authentication. Some of the servers that should authenticate against the AD are placed in a DMZ, so we thought of using a LDAP-server as a proxy, so that only 1 server in the DMZ has to connect to the LAN where the AD-server is placed). With some googling it was no problem to configure the slapd (see slapd.conf below) and it seemed to work when using the ldapsearch tool, so we tried to use it in apache2 htaccess to authenticate the user over the LDAP-proxy. And here comes the problem: We found out the username in the AD is stored in the attribute 'sAMAccountName' so we configured it in .htaccess (see below) but the login didn't work. In the syslog we found out that the filter for the ldapsearch was not (like it should be) '(&(objectClass=*)(sAMAccountName=authtest01))' but '(&(objectClass=*)(?=undefined))' which we found out is slapd's way to show that the attribute do not exists or the value is syntactically wrong for this attribute. We thought of a missing schema and found the microsoft.schema (and the .std / .ext ones of it) and tried to include them in the slapd.conf. Which does not work. We found no working schemata so we just picked out the part about the sAMAccountName and build a microsoft.minimal.schema (see below) that we included. Now we get the more precise log in the syslog: Jun 16 13:32:04 breauthsrv01 slapd[21229]: get_ava: illegal value for attributeType sAMAccountName Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SRCH base="ou=oraise,dc=int,dc=oraise,dc=de" scope=2 deref=3 filter="(&(objectClass=\*)(?sAMAccountName=authtest01))" Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SRCH attr=sAMAccountName Jun 16 13:32:04 breauthsrv01 slapd[21229]: conn=0 op=1 SEARCH RESULT tag=101 err=0 nentries=0 text= Using our Apache htaccess directly with the AD via LDAP works though. Anyone got a working setup? Thanks for any help in advance: slapd.conf: allow bind_v2 include /etc/ldap/schema/core.schema ... include /etc/ldap/schema/microsoft.minimal.schema ... backend ldap database ldap suffix "ou=xxx,dc=int,dc=xxx,dc=de" uri "ldap://80.156.177.161:389" acl-bind bindmethod=simple binddn="CN=authtest01,ou=GPO-Test,ou=xxx,dc=int,dc=xxx,dc=de" credentials=xxxxx .htaccess: AuthBasicProvider ldap AuthType basic AuthName "AuthTest" AuthLDAPURL "ldap://breauthsrv01.xxx.de:389/OU=xxx,DC=int,DC=xxx,DC=de?sAMAccountName?sub" AuthzLDAPAuthoritative On AuthLDAPGroupAttribute member AuthLDAPBindDN CN=authtest02,OU=GPO-Test,OU=xxx,DC=int,DC=xxx,DC=de AuthLDAPBindPassword test123 Require valid-user microsoft.minimal.schema: attributetype ( 1.2.840.113556.1.4.221 NAME 'sAMAccountName' SYNTAX '1.3.6.1.4.1.1466.115.121.1.15' SINGLE-VALUE )

    Read the article

  • Cannot install .NET Framework 4.0 on Windows XP SP3

    - by Bob
    I'm using Windows XP SP3 logged in as the administrator. I had RAID Mirroring running. The motherboard broke earlier in the year. When I got a new battery I did not resync. I just use the disks as two separate disks. I searched Google for the errors but I didn't find anything detailed enough. The following Microsoft components are in Add/Remove programs: .NET Framework 1.1 .NET Framework 2.0 Service Pack 2 .NET Framework 3.0 Service Pack 2 .NET Framework 3.5 SP1 Microsoft Compression Client Pack 1.0 for Windows XP Microsoft Office Enterprise 2007 Microsoft Silverlight Microsoft USB Flash Driver Manager Micrsoft User-mode Driver Framework Feature Pack 1.0 Microsoft Visual C++ 2005 ATL Update KB 973923 x86 8.050727.4053 Microsoft Visual C++ 2005 Redistributable This is the installation log: Exists: evaluating... [10/21/2011, 22:17:14]MsiGetProductInfo with product code {3C3901C5-3455-3E0A-A214-0B093A5070A6} found no matches [10/21/2011, 22:17:14] Exists evaluated to false [10/21/2011, 22:15:50]calling PerformAction on an installing performer [10/21/2011, 22:15:50] Action: Performing actions on all Items... [10/21/2011, 22:15:50]Wait for Item (clr_optimization_v2.0.50727_32) to be available [10/21/2011, 22:15:50]clr_optimization_v2.0.50727_32 is now available to install [10/21/2011, 22:15:50]Creating new Performer for ServiceControl item [10/21/2011, 22:15:50] Action: ServiceControl - Stop clr_optimization_v2.0.50727_32... [10/21/2011, 22:15:50]ServiceControl operation succeeded! [10/21/2011, 22:15:50] Action complete [10/21/2011, 22:15:50]Error 0 is mapped to Custom Error: [10/21/2011, 22:15:50]Wait for Item (Windows6.0-KB956250-v6001-x86.msu) to be available [10/21/2011, 22:15:51]Windows6.0-KB956250-v6001-x86.msu is now available to install [10/21/2011, 22:15:51]Created new DoNothingPerformer for File item [10/21/2011, 22:15:51]No CustomError defined for this item. [10/21/2011, 22:15:51]Wait for Item (Windows6.1-KB958488-v6001-x86.msu) to be available [10/21/2011, 22:15:51]Windows6.1-KB958488-v6001-x86.msu is now available to install [10/21/2011, 22:15:51]Created new DoNothingPerformer for File item [10/21/2011, 22:15:51]No CustomError defined for this item. [10/21/2011, 22:15:51]Wait for Item (netfx_Core.mzz) to be available [10/21/2011, 22:15:52]netfx_Core.mzz is now available to install [10/21/2011, 22:15:52]Created new DoNothingPerformer for File item [10/21/2011, 22:15:52]No CustomError defined for this item. [10/21/2011, 22:15:52]Wait for Item (netfx_Core_x86.msi) to be available [10/21/2011, 22:15:52]netfx_Core_x86.msi is now available to install [10/21/2011, 22:15:52]Creating new Performer for MSI item [10/21/2011, 22:15:52] Action: Performing Action on MSI at F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_4.0.30319\netfx_Core_x86.msi... [10/21/2011, 22:15:52]Log File F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_20111021_221545515-MSI_netfx_Core_x86.msi.txt does not yet exist but may do at Watson upload time [10/21/2011, 22:15:52]Calling MsiInstallProduct(F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_4.0.30319\netfx_Core_x86.msi, EXTUI=1 [10/21/2011, 22:17:14]MSI (F:\DOCUME~1\Owner\LOCALS~1\Temp\Microsoft .NET Framework 4 Client Profile Setup_4.0.30319\netfx_Core_x86.msi) Installation failed. Msi Log: Microsoft .NET Framework 4 Client Profile Setup_20111021_221545515-MSI_netfx_Core_x86.msi.txt [10/21/2011, 22:17:14]PerformOperation returned 1603 (translates to HRESULT = 0x80070643) [10/21/2011, 22:17:14] Action complete [10/21/2011, 22:17:14]OnFailureBehavior for this item is to Rollback. [10/21/2011, 22:17:14] Action: Performing actions on all Items... [10/21/2011, 22:17:14] Action complete [10/21/2011, 22:17:14] Action complete [10/21/2011, 22:17:14]Final Result: Installation failed with error code: (0x80070643), "Fatal error during installation. " (Elapsed time: 0 00:01:29). [10/21/2011, 22:17:41]WM_ACTIVATEAPP: Focus stealer's windows WAS visible, NOT taking back focus SECOND LOG REQUESTED BELOW: MSI (s) (6C:EC) [22:17:13:828]: Invoking remote custom action. DLL: F:\WINDOWS\Installer\MSIBB4.tmp, Entrypoint: NgenUpdateHighestVersionRollback MSI (s) (6C:64) [22:17:13:984]: Executing op: ActionStart(Name=CA_NgenRemoveNicPFROs_I_DEF_x86.3643236F_FC70_11D3_A536_0090278A1BB8,,) MSI (s) (6C:64) [22:17:13:984]: Executing op: ActionStart(Name=CA_NgenRemoveNicPFROs_I_RB_x86.3643236F_FC70_11D3_A536_0090278A1BB8,,) MSI (s) (6C:64) [22:17:13:984]: Executing op: CustomActionRollback(Action=CA_NgenRemoveNicPFROs_I_RB_x86.3643236F_FC70_11D3_A536_0090278A1BB8,ActionType=17729,Source=BinaryData,Target=NgenRemoveNicPFROs,) MSI (s) (6C:AC) [22:17:13:984]: Invoking remote custom action. DLL: F:\WINDOWS\Installer\MSIBB5.tmp, Entrypoint: NgenRemoveNicPFROs MSI (s) (6C:64) [22:17:14:000]: Executing op: End(Checksum=0,ProgressTotalHDWord=0,ProgressTotalLDWord=0) MSI (s) (6C:64) [22:17:14:000]: Error in rollback skipped. Return: 5 MSI (s) (6C:64) [22:17:14:015]: No System Restore sequence number for this installation. MSI (s) (6C:64) [22:17:14:015]: Unlocking Server MSI (s) (6C:64) [22:17:14:015]: PROPERTY CHANGE: Deleting UpdateStarted property. Its current value is '1'. MSI (s) (6C:64) [22:17:14:031]: Note: 1: 1708 MSI (s) (6C:64) [22:17:14:031]: Product: Microsoft .NET Framework 4 Client Profile -- Installation failed. MSI (s) (6C:64) [22:17:14:078]: Cleaning up uninstalled install packages, if any exist MSI (s) (6C:64) [22:17:14:078]: MainEngineThread is returning 1603 MSI (s) (6C:EC) [22:17:14:171]: Destroying RemoteAPI object. MSI (s) (6C:9C) [22:17:14:171]: Custom Action Manager thread ending. MSI (c) (F4:C4) [22:17:14:203]: Decrementing counter to disable shutdown. If counter >= 0, shutdown will be denied. Counter after decrement: -1 MSI (c) (F4:C4) [22:17:14:203]: MainEngineThread is returning 1603 === Verbose logging stopped: 10/21/2011 22:17:14 ===

    Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >