Search Results

Search found 4060 results on 163 pages for '400 the cat'.

Page 70/163 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

• How to get an ARM CPU clock speed in Linux?

  - by MiKy

  I have an ARM-based embedded machine based on S3C2416 board. According to the specifications I have available there should be a 533 MHz ARM9 (ARM926EJ-S according to /proc/cpuinfo), however the software running on it "feels" slow, compared to the same software on my Android phone with a 528MHz ARM CPU. /proc/cpuinfo tells me that BogoMIPS is 266.24. I know that I should not trust BogoMIPS regarding performance ("Bogo" = bogus), however I would like to get a measurement on the actual CPU speed. On x86, I could use the rdtsc instruction to get the time stamp counter, wait a second (sleep(1)), read the counter again to get an approximation on the CPU speed, and according to my experience, this value was close enough to the real CPU speed. How can I find the actual CPU speed of given ARM processor? Update I found this simple Pi calculator, which I compiled both for my Android phone and the ARM board. The results are as follows: S3C2416 # cat /proc/cpuinfo Processor : ARM926EJ-S rev 5 (v5l) BogoMIPS : 266.24 Features : swp half fastmult edsp java ... #./pi_arm 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 8.50 sec. (real time) Android # cat /proc/cpuinfo Processor : ARMv6-compatible processor rev 2 (v6l) BogoMIPS : 527.56 Features : swp half thumb fastmult edsp java # ./pi_android 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 5.95 sec. (real time) So it seems that the ARM926EJ-S is slower than my Android phone, but not twice slower as I would expect by the BogoMIPS figures. I am still unsure about the clock speed of the ARM9 CPU.

  Read the article

• Basic multicast network performance problems

  - by davedavedave

  I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

  Read the article

• How to make gpg2 to flush the stream?

  - by Vi

  I want to get some slowly flowing data saved in encrypted form at the device which can be turned off abruptly. But gpg2 seems to not to flush it's output frequently and I get broken files when I try to read such truncated file. vi@vi-notebook:~$ cat asdkfgmafl asdkfgmafl ggggg ggggg 2342 2342 cat behaves normally. I see the output right after input. vi@vi-notebook:~$ gpg2 -er _Vi --batch ?pE??x...(more binary data here)....???-??.... asdfsadf 22223 sdfsdfasf Still no data... Still no output... ^C gpg: signal Interrupt caught ... exiting vi@vi-notebook:~$ gpg2 -er _Vi --batch /tmp/qqq skdmfasldf gkvmdfwwerwer zfzdfdsfl ^\ gpg: signal Quit caught ... exiting Quit vi@vi-notebook:~$ gpg2 < /tmp/qqq You need a passphrase to unlock the secret key for user: "Vitaly Shukela (_Vi) " 2048-bit ELG key, ID 78F446CA, created 2008-01-06 (main key ID 1735A052) gpg: [don't know]: 1st length byte missing vi@vi-notebook:~$ # Where is my "skdmfasldf" How to make gpg2 to handle such case? I want it to put enough output to reconstruct each incoming chunk of input. (Also fsyncing after each output can be benefitial as an additional option). Should I use other tool (I need pubkey encryption).

  Read the article

• CSS gradient not rendering in Windows Phone 8 WebBrowser Control

  - by SRSHawk

  I am facing an issue where, the CSS3 background is not rendered in WebBrowser control in Windows Phone 8. But same HTML when opened in WebBrowser in Windows Phone 8, it renders the gradient The HTML I am using is: <html> <head> <meta name="viewport" content="width=320, user-scalable=no, minimum-scale=1, maximum-scale=1"/> </head> <body style="margin:0px;overflow:hidden;"> <div id="im_c" style="height:48px;width:100%25; background: -ms-linear-gradient( bottom, #432100 30%, #00AAAA 70%);"> <div style="margin:0 auto;width:320px;"> Test </div> </div> <style> body {margin:0px} </style> </body> In Windows Phone 8, I use the HTML as below: WebBroswer WebView = new WebBrowser(); WebView.Height = 100; WebView.Width = 400; WebView.NavigateToString(@"<html><head><meta name=""viewport"" content=""width=320, user-scalable=no, minimum-scale=1, maximum-scale=1""/></head><body style=""margin:0px;overflow:hidden;""> <div id=""im_c"" style=""height:48px;width:100%25; background: -ms-linear-gradient( bottom, #432100 30%, #00AAAA 70%);""> <div style=""margin:0 auto;width:320px;"">Test</div></div> <style> body {margin:0px} </style> </body></html>"); In this case, the CSS gradient is not visible. Am I missing something?

  Read the article

• COMPAQ Tower No Signal to monitor

  - by Lancelot

  Hi there, I have had some troubles with this: I received a compaq tower: Compaq Presario SR1224NX Onboard VGA Windows XP SP2 from a friend. It was given to me on condition i give her the files back. My plan was to turn this into an Ubuntu Server. It booted up no problems even with the ubuntu live disc. After a normal shutdown(not unpluggin the power cord and not doing a hard shutdown with the power button), it would not restart even after SEVERAL attempts. I realized the light next to the power supply would flash very rapidly. I researched and found out it was one of two things: a dead power supply or the cables to the motherboard and to the disks etc. Thus i checked to ensure the cables were fine(and they were). I purchased a Power Supply (this one has 400 watts, the initial had 250) and installed it. The tower now boots. It booted into the live disk and everything. After a normal shutdown, it now restarts but is not sending signal to my monitor. I have tried several monitors in which i assure work perfectly but not with this tower(i recall it did show display after replacing the power supply). The monitors are ACER. This is different than most "no Signal" problems since i am not using an external Video Card, this is onboard VGA. Thanks!

  Read the article

• Midnight Commander Woes: Output while panels are active, and tab completion.

  - by Eddie Parker

  I'm trying out midnight commander (loved Norton back in the day!) and I'm finding two things hard to work out. I'm curious if there's ways around this or not however. 1) If the panels are active and I issue a command that has a lot of output, it appears to be lost forever. i.e., if the panels are visible and I cat something (i.e., cat /proc/cpuinfo), that info is gone forever once the panels get redrawn. Is there anyway to see the output? I've tried 'ctrl-o', but it appears to just give me a fresh sub-shell and wipes the previous output away. Pausing after every invocation is a bit irritating, so I'd rather not use that option. 2) Tab completion for commands When mc is running, it consumes the tab character for switching panels. Is there any way to get around this so I can still type in paths and what not on the command line? I'm running cygwin if that matters at all.

  Read the article

• Batch deletion of smaller files from group of files via unix command line

  - by artlung

  I have a large number (more than 400) of directories full of photos. What I want to do is to keep the larger sizes of these photos. Each directory has 31 to 66 files in it. Each directory has thumbnails, and larger versions, plus a file called example.jpg I dispatched the example.jpg file easily with: rm */example.jpg I initially thought that it would be easy to delete the thumbnails, but the problem is they are not consistently named. The typical pattern was photo1.jpg and photo1s.jpg. I did rm */photo*s.jpg but it ended up some of the files named photoXs.jpg were actually larger and not smaller. Argh. So what I want to do is scan each directory for filesize and delete (or move) the thumbnails. I initially thought I'd just ls -R every file and extract the size of each file and save those under a threshold. The problem? In one directory the large will be 1.1 MB and the thumb is 200k. In another the large is 200k and the small 30k. Even worse, the files really are mostly named photo1.jpg - so simply putting them all in the same folder, sorting by size, and deleting in groups would not work without renaming already, and if it's possible I'd prefer to keep them in their folders. I was almost resolved to just doing this all manually, but then thought I'd ask here. How would you do this task?

  Read the article

• Increasing Java's heapspace in Tomcat startup script

  - by Ankur

  I want to increase my heap size when using Tomcat. I was told to add this line export CATALINA_OPTS=-Xms16m -Xmx256m; In to the startup.sh script - I did so (at the beginning) but got the error export: 24: -Xmx256m: bad variable name Where am I supposed to add it, am I doing something else wrong? <b>export CATALINA_OPTS=-Xms16m -Xmx256m;</b> # Better OS/400 detection: see Bugzilla 31132 os400=false darwin=false case "`uname`" in CYGWIN*) cygwin=true;; OS400*) os400=true;; Darwin*) darwin=true;; esac # resolve links - $0 may be a softlink PRG="$0" while [ -h "$PRG" ] ; do ls=`ls -ld "$PRG"` link=`expr "$ls" : '.*-> \(.*\)$'` if expr "$link" : '/.*' > /dev/null; then PRG="$link" else PRG=`dirname "$PRG"`/"$link" fi done PRGDIR=`dirname "$PRG"` EXECUTABLE=catalina.sh # Check that target executable exists if $os400; then # -x will Only work on the os400 if the files are: # 1. owned by the user # 2. owned by the PRIMARY group of the user # this will not work if the user belongs in secondary groups eval else if [ ! -x "$PRGDIR"/"$EXECUTABLE" ]; then echo "Cannot find $PRGDIR/$EXECUTABLE" echo "This file is needed to run this program" exit 1 fi fi exec "$PRGDIR"/"$EXECUTABLE" start "$@"

  Read the article

• Invalid Parameter on node puppet

  - by chandank

  I am getting an error of err: Could not retrieve catalog from remote server: Error 400 on SERVER: Invalid parameter port at /etc/puppet/manifests/nodes/node.pp:652 on node test-puppet My puppet class: (The Line 652 at node.pp) node 'test-puppet' { class { 'syslog_ng': host => "newhost", ip => "192.168.1.10", port => "1999", logfile => "/var/log/test.log", } } On the module side class syslog_ng::config ( $host , $ip , $port, $logfile){ file {'/etc/syslog-ng/syslog-ng.conf': ensure => present, owner => 'root', group => 'root', content => template('syslog-ng/syslog-ng.conf.erb'), notify => Service['syslog-ng'], require => Class['syslog_ng::install'], } file {"/etc/syslog-ng/conf/${host}.conf": ensure => present, owner => 'root', group => 'root', notify => Service['syslog-ng'], content => template("syslog-ng/${host}.conf.erb"), require => Class['syslog_ng::install'], } } I think I am doing it as per the puppet documentation.

  Read the article

• Windows 7 network performance tuning for LAN

  - by Hubert Kario

  I want to tune Windows 7 TCP stack for speed in a LAN environment. Bit of background info: I've got a Citrix XenServer set up with Windows 2008R2, Windows 7 and Debian Lenny with Citrix kernel, Windows machines have Tools installed the iperf server process is running on different host, also Debian Lenny. The servers are otherwise idle, tests were repeated few times to confirm results. While testing with iperf 2008R2 can achieve around 600-700Mbps with no tuning what so ever but I can't find any guide or set of parameters that will make Windows 7 achieve anything over 150Mbps with no change in TCP window size using -w parameter to iperf. I tried using netsh autotuining to disabled, experimental, normal and highlyrestricted - no change. Changing congestionprovider doesn't do anything, just as rss and chimney. Setting all the available settings to same values as on Windows 2008R2 host doesn't help. To summarize: Windows 2008R2 default settings: 600-700Mbps Debian, default settings: 600Mbps Windows 7 default settings: 120Mbps Windows 7 default, iperf -w 65536: 400-500Mbps While the missing 400Mbps in performance I blame on crappy Realtek NIC in the XenServer host (I can do ~980Mbps from my laptop to the iperf server) it doesn't explain why Windows 7 can't achieve good performance without manually tuning window size at the application level. So, how to tune Windows 7?

  Read the article

• What's wrong with this HTTP POST request?

  - by bigboy

  I'm trying to fuzz a server using the Sulley fuzzing framework. I observe the following stream in Wireshark. The error talks about a problem with JSON parsing, however, when I try the same HTTP POST request using Google Chrome's Postman extension, it succeeds. Can anyone please explain what could be wrong about this HTTP POST request? The JSON seems valid. POST /restconf/config HTTP/1.1 Host: 127.0.0.1:8080 Accept: */* Content-Type: application/yang.data+json { "toaster:toaster" : { "toaster:toasterManufacturer" : "Geqq", "toaster:toasterModelNumber" : "asaxc", "toaster:toasterStatus" : "_." }} HTTP/1.1 400 Bad Request Server: Apache-Coyote/1.1 Content-Type: */* Transfer-Encoding: chunked Date: Sat, 07 Jun 2014 05:26:35 GMT Connection: close 152 <?xml version="1.0" encoding="UTF-8" standalone="no"?> <errors xmlns="urn:ietf:params:xml:ns:yang:ietf-restconf"> <error> <error-type>protocol</error-type> <error-tag>malformed-message</error-tag> <error-message>Error parsing input: Root element of Json has to be Object</error-message> </error> </errors> 0

  Read the article

• limits.conf to set memory limits

  - by Rupert Jipe

  I would like to limit any process from using more than 500 MB of RAM. AFAIK this is done using RSS in /etc/security/limits.conf but the process called gnome-panel apparently is using 618436 kB of VmRSS. How can this be ? /etc/security/limits.conf * hard rss 512000 username@debian:~$ cat /proc/3002/status Name: gnome-panel State: S (sleeping) Tgid: 3002 Pid: 3002 PPid: 2910 TracerPid: 0 Uid: 1000 1000 1000 1000 Gid: 1000 1000 1000 1000 FDSize: 64 Groups: 20 24 25 29 44 46 112 116 117 1000 1002 1003 VmPeak: 916636 kB VmSize: 916636 kB VmLck: 0 kB VmHWM: 618436 kB VmRSS: 618436 kB VmData: 601972 kB VmStk: 104 kB VmExe: 516 kB VmLib: 29232 kB VmPTE: 1760 kB Threads: 1 SigQ: 0/14001 SigPnd: 0000000000000000 ShdPnd: 0000000000000000 SigBlk: 0000000000000000 SigIgn: 0000000020001000 SigCgt: 0000000180000000 CapInh: 0000000000000000 CapPrm: 0000000000000000 CapEff: 0000000000000000 CapBnd: ffffffffffffffff Cpus_allowed: 3 Cpus_allowed_list: 0-1 Mems_allowed: 00000000,00000001 Mems_allowed_list: 0 voluntary_ctxt_switches: 871965 nonvoluntary_ctxt_switches: 47553 PaX: PeMRs username@debian:~$ cat /proc/3002/limits Limit Soft Limit Hard Limit Units Max cpu time unlimited unlimited seconds Max file size unlimited unlimited bytes Max data size unlimited unlimited bytes Max stack size 8388608 unlimited bytes Max core file size 0 0 bytes Max resident set 524288000 524288000 bytes Max processes 100 100 processes Max open files 1024 1024 files Max locked memory 65536 65536 bytes Max address space unlimited unlimited bytes Max file locks unlimited unlimited locks Max pending signals 14001 14001 signals Max msgqueue size 819200 819200 bytes Max nice priority 0 0 Max realtime priority 0 0 Max realtime timeout unlimited unlimited us

  Read the article

• How to populate RRD database with CPU and MEM usage data?

  - by Tomaszs

  I have a Lighttpd server (on Centos) and would like to display 4 graphs: lighttpd traffic, lighttpd requests per second, CPU usage and MEM usage. I've set place for rrd database for lighttpd config like this: rrdtool.binary = "/usr/bin/rrdtool" rrdtool.db-name = "/var/www/lighttpd.rrd" And put into my WWW cgi-bin sh file that gets data from lighttpd RRD file and creates graphs of traffic and requests per second like this: #!/bin/sh RRDTOOL=/usr/bin/rrdtool OUTDIR=//var/www/graphs INFILE=/var/www/lighttpd.rrd OUTPRE=lighttpd-traffic WIDTH=400 HEIGHT=100 DISP="-v bytes --title TrafficWebserver \ DEF:binraw=$INFILE:InOctets:AVERAGE \ DEF:binmaxraw=$INFILE:InOctets:MAX \ DEF:binminraw=$INFILE:InOctets:MIN \ DEF:bout=$INFILE:OutOctets:AVERAGE \ DEF:boutmax=$INFILE:OutOctets:MAX \ DEF:boutmin=$INFILE:OutOctets:MIN \ CDEF:bin=binraw,-1,* \ CDEF:binmax=binmaxraw,-1,* \ CDEF:binmin=binminraw,-1,* \ CDEF:binminmax=binmaxraw,binminraw,- \ CDEF:boutminmax=boutmax,boutmin,- \ AREA:binmin#ffffff: \ STACK:binmax#f00000: \ LINE1:binmin#a0a0a0: \ LINE1:binmax#a0a0a0: \ LINE2:bin#efb71d:incoming \ GPRINT:bin:MIN:%.2lf \ GPRINT:bin:AVERAGE:%.2lf \ GPRINT:bin:MAX:%.2lf \ AREA:boutmin#ffffff: \ STACK:boutminmax#00f000: \ LINE1:boutmin#a0a0a0: \ LINE1:boutmax#a0a0a0: \ LINE2:bout#a0a735:outgoing \ GPRINT:bout:MIN:%.2lf \ GPRINT:bout:AVERAGE:%.2lf \ GPRINT:bout:MAX:%.2lf \ " $RRDTOOL graph $OUTDIR/$OUTPRE-hour.png -a PNG --start -14400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-day.png -a PNG --start -86400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-month.png -a PNG --start -2592000 $DISP -w $WIDTH -h $HEIGHT OUTPRE=lighttpd-requests DISP="-v req --title RequestsperSecond -u 1 \ DEF:req=$INFILE:Requests:AVERAGE \ DEF:reqmax=$INFILE:Requests:MAX \ DEF:reqmin=$INFILE:Requests:MIN \ CDEF:reqminmax=reqmax,reqmin,- \ AREA:reqmin#ffffff: \ STACK:reqminmax#00f000: \ LINE1:reqmin#a0a0a0: \ LINE1:reqmax#a0a0a0: \ LINE2:req#00a735:requests" $RRDTOOL graph $OUTDIR/$OUTPRE-hour.png -a PNG --start -14400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-day.png -a PNG --start -86400 $DISP -w $WIDTH -h $HEIGHT $RRDTOOL graph $OUTDIR/$OUTPRE-month.png -a PNG --start -2592000 $DISP -w $WIDTH -h $HEIGHT Basically it's not my script, i get it from somewhere from the internet. Now i would like to do the same for CPU usage and MEM usage. I don't like to use any additional packages! As you can see lighttpd populates lighttpd.rrd file with traffic data and requests per second. Now i would like to the system to populate second rrd file with CPU and MEM usage, so i can add to sh file code to generate graphs for this data. How can I populate RRD file with CPU and MEM usage data? Please, NO THIRD-PARTY tools !

  Read the article

• Printing to a remote printer through the internet

  - by Lock

  I have a remote network (A) that is connected to a head office (B) through a private network. Network A only has 1 PC that requires the connection, and this is into a terminal server at network B. We want to save money by getting rid of the private network as only 1 PC now access it and it seems silly to pay ~$400 per month for something that is accessed by 1 PC. A VPN tunnel is out of the question as the provider wants to charge $600 a month for a VPN tunnel (more than a private network? I might get them to check these numbers). I was thinking of 2 options: 1) VPN client on the PC. This wouldn't cost a thing as we already have VPN users available. 2) Open up a port on the firewall of network B, forwarding to the terminal server. Now the problem is this: On the terminal server, the program that is accessed is for printing labels to the printer that is at network A. The program is setup to send all print jobs to a printer that is setup locally on the terminal server, which has its port mapped to the IP address of the printer that is at network A. If we got rid of the VPN tunnel and used clients/open up firewall port, the printer would no longer be able to find network A, and hence printing would not work. Any ideas to combat this issue? Can the printers at the remote network be setup as internet printers? I've never had any experience with internet printers. Can you open up ports and map to a public static IP address?

  Read the article

• Viability of Apache (MPM Worker), FastCGI PHP 4/5.2/5.3, and MySQL 5

  - by Adrian

  My server will be hosting numerous PHP web applications ranging from Joomla, Drupal, and some legacy (read: PHP4) and other custom-built code inherited from clients. This will be a development machine used by a dozen or so web developers and issues like fluctuating loads or particularly high load expectations are not important. Now, my question: are there any concerns I should know about when using Apache w/ MPM Worker, PHP 4/PHP 5.2/PHP 5.3 (all via FastCGI), and MySQL 5 (with a query cache of 64MB)? I have not tested the various applications extensively and I have only recently learned how to install PHP and utilize it via FastCGI (rather than mod_php, which in this case seemed impossible (considering the multiple versions of PHP and the desire to use MPM Worker over MPM Prefork)). I have come to understand that there could be concerns regarding XCache and APC, namely non-thread-safety issues where data becomes corrupted and the capability to use MPM Worker becomes null and void. Is this a valid concern? I have been using my personal testing server (running Ubuntu Server Edition 10.04 in VirtualBox) which has 2GB of RAM available to it. Here is the configuration used (the actual server will likely use a configuration more tailored to suit it's purposes): Apache: Server version: Apache/2.2.14 (Ubuntu) Server built: Apr 13 2010 20:22:19 Server's Module Magic Number: 20051115:23 Server loaded: APR 1.3.8, APR-Util 1.3.9 Compiled using: APR 1.3.8, APR-Util 1.3.9 Architecture: 64-bit Server MPM: Worker threaded: yes (fixed thread count) forked: yes (variable process count) Worker: <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 400 MaxRequestsPerChild 2000 </IfModule> PHP ./configure (PHP 4.4.9, PHP 5.2.13, PHP 5.3.2): --enable-bcmath \ --enable-calendar \ --enable-exif \ --enable-ftp \ --enable-mbstring \ --enable-pcntl \ --enable-soap \ --enable-sockets \ --enable-sqlite-utf8 \ --enable-wddx \ --enable-zip \ --enable-fastcgi \ --with-zlib \ --with-gettext \ Apache php-fastcgi-setup.conf FastCgiServer /var/www/cgi-bin/php-cgi-5.3.2 FastCgiServer /var/www/cgi-bin/php-cgi-5.2.13 FastCgiServer /var/www/cgi-bin/php-cgi-4.4.9 ScriptAlias /cgi-bin-php/ /var/www/cgi-bin/

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Access 2007: How can I make this EXPRESSION less complex?

  - by Mike

  Access is telling me that my new expression is to complex. It used to work when we had 10 service levels, but now we have 19! Great! My expression is checking the COST of our services in the [PriceCharged] field and then assigning the appropriate HOURS [Servicelevel] when I perform a calculation to work out how much REVENUE each colleague has made when working for a client. The [EstimatedTime] field stores the actual hours each colleague has worked. [EstimatedTime]/[ServiceLevel]*[PriceCharged] Great. Below is the breakdown of my COST to HOURS expression. I've put them on different lines to make it easier to read - please do not be put off by the length of this post, it's all the same info in the end. Many thanks,Mike ServiceLevel: IIf([pricecharged]=100(COST),6(HOURS), IIf([pricecharged]=200 Or [pricecharged]=210,12.5, IIf([pricecharged]=300,19, IIf([pricecharged]=400 Or [pricecharged]=410,25, IIf([pricecharged]=500,31, IIf([pricecharged]=600,37.5, IIf([pricecharged]=700,43, IIf([pricecharged]=800 Or [pricecharged]=810,50, IIf([pricecharged]=900,56, IIf([pricecharged]=1000,62.5, IIf([pricecharged]=1100,69, IIf([pricecharged]=1200 Or [pricecharged]=1210,75, IIf([pricecharged]=1300 Or [pricecharged]=1310,100, IIf([pricecharged]=1400,125, IIf([pricecharged]=1500,150, IIf([pricecharged]=1600,175, IIf([pricecharged]=1700,200, IIf([pricecharged]=1800,225, IIf([pricecharged]=1900,250,0)))))))))))))))))))

  Read the article

• Why can't I get rid of default index.html even if I disable the default virtual host in Apache2?

  - by Emre Sevinç

  I have created a virtual host settings file and I disabled the default settings by using a2dissite default (this is a pretty standard Ubuntu 10.04 installation). But no matter what I try my Apache2 server simply keeps on displaying the default index.html page instead of the index.php page that I set up in the virtual host file. Can someone help me what I'm missing. Details follow: No default settings: ls -l /etc/apache2/sites-enabled/ total 0 lrwxrwxrwx 1 root root 51 May 5 13:32 webmin.1273066327.conf -> /etc/apache2/sites-available/webmin.1273066327.conf lrwxrwxrwx 1 root root 34 May 30 11:03 www.accontax.be -> ../sites-available/www.accontax.be Contents of the relevant virtual host: cat /etc/apache2/sites-enabled/www.accontax.be <VirtualHost *> ServerName www.accontax.be ServerAlias accontax.be DirectoryIndex index.php DocumentRoot /var/www/drupal/ <Directory /var/www/drupal/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> Contents of httpd.conf: cat /etc/apache2/httpd.conf Listen 80 NameVirtualHost * I also have those relevant lines in my apache2.conf: # Include generic snippets of statements Include /etc/apache2/conf.d/ # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ When I visit http://www.accontax.be I expect apache2 server go to the /var/www/drupal subdirectory and start serving index.php but it simply keeps on serving index.html from /var/www directory. I have reloaded the configuration, restarted the server, deleted my browser cache. Nothing changed. Probably I'm missing a simple yet crucial step but I just could not find it.

  Read the article

• Is Subversion(SVN) supported on Ubuntu 10.04 LTS 32bit?

  - by Chad

  I've setup subversion on Ubuntu 10.04, but can't get authentication to work. I believe all my config files are setup correctly, However I keep getting prompted for credentials on a SVN CHECKOUT. Like there is an issue with apache2 talking to svnserve. If I allow anonymous access checkout works fine. Does anybody know if there is a known issue with subversion and 10.04 or see a error in my configuration? below is my configuration: # fresh install of Ubuntu 10.04 LTS 32bit sudo apt-get install apache2 apache2-utils -y sudo apt-get install subversion libapache2-svn subversion-tools -y sudo mkdir /svn sudo svnadmin create /svn/DataTeam sudo svnadmin create /svn/ReportingTeam #Setup the svn config file sudo vi /etc/apache2/mods-available/dav_svn.conf #replace file with the following. <Location /svn> DAV svn SVNParentPath /svn/ AuthType Basic AuthName "Subversion Server" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user AuthzSVNAccessFile /etc/apache2/svn_acl </Location> sudo touch /etc/apache2/svn_acl #replace file with the following. [groups] dba_group = tom, jerry report_group = tom [DataTeam:/] @dba_group = rw [ReportingTeam:/] @report_group = rw #Start/Stop subversion automatically sudo /etc/init.d/apache2 restart cd /etc/init.d/ sudo touch subversion sudo cat 'svnserve -d -r /svn' > svnserve sudo cat '/etc/init.d/apache2 restart' >> svnserve sudo chmod +x svnserve sudo update-rc.d svnserve defaults #Add svn users sudo htpasswd -cpb /etc/apache2/dav_svn.passwd tom tom sudo htpasswd -pb /etc/apache2/dav_svn.passwd jerry jerry #Test by performing a checkout sudo svnserve -d -r /svn sudo /etc/init.d/apache2 restart svn checkout http://127.0.0.1/svn/DataTeam /tmp/DataTeam

  Read the article

• Nginx with http/https - Http seemed redirected to https all the time

  - by dwarfy

  I've this really weird behaviour with my ubuntu 10.04 / nginx 1.2.3 server. Basically I changed the SSL certificates this morning. And ever since it has been behaving weirdly on all apps. Godaddy is reporting that HTTPS/SSL setup is correct. When I try a page it still works correctly when I'm using HTTPS. But when I try using HTTP nginx reports error : 400 Bad Request The plain HTTP request was sent to HTTPS port After looking around on google for hours, I've tried different setup (while originaly my setup was working correctly for longtime, I just renewed certificates) I kindof found a half solution by adding this to my config : error_page 497 $request_uri; The realllly weird thing is that when I use this setup : server { listen 80; server_name john.johnrocks.eu; access_log /home/john/envs/john_prod/nginx_access.log; error_log /home/john/envs/john_prod/nginx_error.log; location / { uwsgi_pass unix:///home/john/envs/john_prod/john.sock; include uwsgi_params; } location /media { alias /home/john/envs/john_prod/johntab/www; } location /adminmedia { alias /home/john/envs/john_prod/johntab/www/adminmedia; } } I still have the same error when using HTTP (while nothing is setup for HTTPS here)?? I'm getting crazy on this !

  Read the article

• pdftotext not outputting hebrew characters

  - by Ofri Raviv

  I'm using Xpdf's pdftotext to get the text out of some hebrew pdf files on Ubuntu. On my local machine this worked fine. I then tried to do it on another machine and the hebrew characters don't show up in the text file. I verified that I have the language package (see below why I think so). Where else can I look for the problem? >> tail -2 /etc/xpdf/xpdfrc include /etc/xpdf/includes >> cat /etc/xpdf/includes # This file was automatically generated by /usr/sbin/update-xpdfrc. # Instead, add or remove files in /etc/xpdf/ then run # /usr/sbin/update-xpdfrc to regenerate this file. include /etc/xpdf/xpdfrc-latin2 include /etc/xpdf/xpdfrc-thai include /etc/xpdf/xpdfrc-greek include /etc/xpdf/xpdfrc-turkish include /etc/xpdf/xpdfrc-arabic include /etc/xpdf/xpdfrc-hebrew include /etc/xpdf/xpdfrc-cyrillic >> cat /etc/xpdf/xpdfrc-hebrew #----- begin Hebrew support package (2003-feb-16) unicodeMap ISO-8859-8 /usr/share/xpdf/hebrew/ISO-8859-8.unicodeMap unicodeMap Windows-1255 /usr/share/xpdf/hebrew/Windows-1255.unicodeMap #----- end Hebrew support package >> ls /usr/share/xpdf/hebrew/ ISO-8859-8.unicodeMap Windows-1255.unicodeMap

  Read the article

• Reducing video mode switching during Linux boot

  - by Zack

  When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

  Read the article

• Wastage of resources in Virtualization

  - by Sabeen Malik

  I have asked this question on SO, but was suggested that i ask it here on SF, so here it goes. http://stackoverflow.com/questions/3010753/wastage-of-resources-in-virtualization I am not sure if this is the right place to ask the question. However i hope it is. When looking for a VPS earlier today, I was trying to understand how each container would work in the background. Keeping in mind the fact that the operating system uses most of the memory and power on a system, wouldn't having multiple operating systems in the same machine mean more wastage of resources. For instance if i was running centOS on a dedicated box and it was running lets say 20 background OS level processes. Then i go and install a virtualization platform and install 5 more centOS virtual machines in the same system which are exactly the same as the host operating system. Doesn't this mean duplication of those 20 processes 6 times? So internally the context switching is happening between 120 processes instead of 20? Further Notes: Here is an example of what i am thinking: I have a master-slave configuration for a long running, cpu + memory intensive process, which can be distributed to 4 machines. Lets say when the process runs on these 4 machines with lets say 1 Gh CPU and 1 Gig RAM, i get 400 results per hour from the cluster (assuming 100 results from one machine) . Now i get a bigger machine ( lets say 4Gh and 4 Gig RAM), have 4 virtual hosts on it with 1 Gz CPU and 1 Gig RAM. Will this configuration give me the same 4 results per hour from these 4 virtual hosts?

  Read the article

• HAproxy with MySQL Master-Master Replication incredibly slow

  - by Yayap

  I have two MySQL servers in multi-master mode, with an HAproxy machine for simple load balancing/redundancy. When I am connected to one of the servers directly and try to update about 100,000 entries, it is completed including replication in about half a minute. When connecting through the proxy it takes usually over three whole minutes. Is it normal to have that type of latency? Is something amiss with my proxy configuration (included below)? This is getting really frustrating as I assumed the proxy would do some sort of load balancing, or at least have little to no overhead. #--------------------------------------------------------------------- # Example configuration for a possible web application. See the # full configuration options online. # # http://haproxy.1wt.eu/download/1.4/doc/configuration.txt # #--------------------------------------------------------------------- #--------------------------------------------------------------------- # Global settings #--------------------------------------------------------------------- global # to have these messages end up in /var/log/haproxy.log you will # need to: # # 1) configure syslog to accept network log events. This is done # by adding the '-r' option to the SYSLOGD_OPTIONS in # /etc/sysconfig/syslog # # 2) configure local2 events to go to the /var/log/haproxy.log # file. A line like the following can be added to # /etc/sysconfig/syslog # # local2.* /var/log/haproxy.log # log 127.0.0.1 local2 # chroot /var/lib/haproxy # pidfile /var/run/haproxy.pid maxconn 4096 user haproxy group haproxy daemon #debug #quiet # turn on stats unix socket stats socket /var/lib/haproxy/stats #--------------------------------------------------------------------- # common defaults that all the 'listen' and 'backend' sections will # use if not designated in their block #--------------------------------------------------------------------- defaults mode tcp log global #option tcplog option dontlognull option tcp-smart-accept option tcp-smart-connect #option http-server-close #option forwardfor except 127.0.0.0/8 #option redispatch retries 3 #timeout http-request 10s #timeout queue 1m timeout connect 400 timeout client 500 timeout server 300 #timeout http-keep-alive 10s #timeout check 10s maxconn 2000 listen mysql-cluster 0.0.0.0:3306 mode tcp balance roundrobin option tcpka option httpchk server db01 192.168.15.118:3306 weight 1 inter 1s rise 1 fall 1 server db02 192.168.15.119:3306 weight 1 inter 1s rise 1 fall 1

  Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >