Search Results

Search found 9617 results on 385 pages for 'fresh dev'.

Page 70/385 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

• External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

  - by kimangroo

  I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

  Read the article

• New Slides - and a discussion about Dictionary Statistics

  - by Mike Dietrich

  First of all we have just upoaded a new version of the Upgrade and Migration Workshop slides with some added information. So please feel free to download them from here.The slides have one new interesting information which lead to a discussion I've had in the past days with a very large customer regarding their upgrades - and internally on the mailing list targeting an EBS database upgrade from Oracle 10.2 to Oracle 11.2. Why are we creating dictionary statistics during upgrade? I'd believe this forced dictionary statistics creation got introduced with the desupport of the Rule Based Optimizer in Oracle 10g. The goal: as RBO is not supported anymore we have to make sure that the data dictionary has fresh and non-stale statistics. Actually that would have led in Oracle 9i to strange behaviour in some databases - so in Oracle 9i this was strongly disrecommended. The upgrade scripts got hardcoded to create these stats. But during tests we had the following findings: It's important to create dictionary statistics the night before the upgrade. Not two weeks before, not 60 minutes before your downtime begins. But very close to the upgrade. From Oracle 10g onwards you'd just say: $ execute DBMS_STATS.GATHER_DICTIONARY_STATS; This is important to make sure you have fresh dictionary statistics during upgrade for performance reasons. Tests have shown that running an upgrade without valid dictionary statistics might slow down the whole upgrade by factors of 2x-3x. And it would be also a great idea post upgrade to create again fresh dictionary statistics when you've did suppress the stats creation during the upgrade process. Suppress? Yes, you could set this underscore parameter in the init.ora: _optim_dict_stats_at_db_cr_upg=FALSE to suppress the forced dictionary statistics collection during an upgrade. We believe strongly that (a) people using the default statistics creation process which will create dictionary statistics by default and (b) create fresh stats before upgrade on the dictionary. Therefore we find it save once you have followed our advice to use the underscore during upgrade. And we've taken out that forced statistics collection during upgrade in the next release of the database. Please note: If you are using the DBUA for the upgrade it will remove underscore parameters for the upgrade run to improve performance - which is generally a good idea. So you'll have to start the DBUA with that call: $ dbua -initParam "_optim_dict_stats_at_cb_cr_upg"=FALSE -Mike

  Read the article

• How migrate my keyring (containing ssh passprases, nautilus remote filesystem, pgp passwords) and network manager connections?

  - by con-f-use

  I changed the disk on my laptop and installed Ubuntu on the new disk. Old disk had 12.04 upgraded to 12.10 on it. Now I want to copy my old keyring with WiFi passwords, ftp passwords for nautilus and ssh key passphrases. I have the whole data from the old disk available (is now a USB disk and I did not delete the old data yet or do anything with it - I could still put it in the laptop and boot from it like nothing happened). On the new disc that is now in my laptop, I have installed 12.10 with the same password, user-id and username as on the old disk. Then I copied a few important config files from the old disk (e.g. ~/.firefox/, ~/.mozilla, ~/.skype and so on, which all worked fine... except for the key ring: The old methods of just copying ~/.gconf/... and ~/.gnome2/keyrings won't work. Did I miss something? 1. Edit: I figure one needs to copy files not located in the users home directory as well. I copied the whole old /home/confus (which is my home directory) to the fresh install to no effect. That whole copy is now reverted to the fresh install's home directory, so my /home/confus is as it was the after fresh install. 2. Edit: The folder /etc/NetworkManager/system-connections seems to be the place for WiFi passwords. Could be that /usr/share/keyrings is important as well for ssh keys - that's the only sensible thing that a search came up with: find /usr/ -name "*keyring* 3. Edit: Still no ssh and ftp passwords from the keyring. What I did: Convert old hard drive to usb drive Put new drive in the laptop and installed fresh version of 12.10 there (same uid, username and passwort) Booted from old hdd via USB and copied its /etc/NetwrokManager/system-connections, ~/.gconf/ and ~/.gnome2/keyrings, ~/.ssh over to the new disk. Confirmed that all keys on the old install work Booted from new disk Result: No passphrase for ssh keys, no ftp passwords in keyring. At least the WiFi passwords are migrated. 4. Edit: Boutny! Ending soon... 5. Edit: Keyring's now in ./local/share/keyrings/. Also interesting .gnupg

  Read the article

• Will default applications be automatically changed during release upgrade?

  - by Jasper Loy

  Suppose LibreOffice and Banshee are set to replace OpenOffice and Rhythmbox in Natty Narwhal. Of course doing a fresh install will give me these new applications to be the default ones. However if I choose to upgrade via the update manager, will the old applications be uninstalled and the new ones installed automatically, or do I have to do these manually so that I get the same experience as a fresh install?

  Read the article

• Why has hibernation stopped working after moving my 12.04 install to a different laptop?

  - by megabytephreak

  I recently got a new laptop (Thinkpad X230). I didn't really have time to do a fresh install so I copied my install (xubuntu 12.04) over from my old machine (Thinkpad X61). Now when I try to hibernate it seems to do the Hibernate step fine, but doesn't seem to try and resume when booting back up. It just does a fresh boot. Is there something I need to do so the system knows where to look for the hibernation data?

  Read the article

• Why does Ubuntu 12.04 dual boot fail?

  - by Tranas

  Fresh install of XP followed by a fresh install of Ubuntu 12.04 results in the following error: error: unknown filesystem. grub rescue and the machine will not boot. Prior to the 12.04 install, XP worked fine. During the 12.04 install, all partitions and free space was visible, and the install seemed to complete without issues until the error message. Although I can fix the MBR via recovery console in XP and allow the machine to boot to windows, why is GRUB/Ubuntu trashing the boot sequence?

  Read the article

• hyperv machine guest loads slow

  - by Dani Avni

  this is by far one of the strangest things I have seen. I have a win 2008R2 cluster with a CSV. the CSV itself is on an iSCSI storage (hitachi HUS 110) basic config of the two hosts in the cluster is Dell R610 Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI these machine work great and I can load a 2008R2 test guest machine on them in less than 90 seconds after the above config is running for over a year, I now need to add a new host. now the host is Dell R620 (Still intel but different CPU) Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI I added this new host to the domain and to the cluster, I gave it access to the CSV and I tried loading the same guest machine that loads in 90 seconds in the other hosts. the machine loads in about 6 minutes. no matter how many times I try this the old hosts load the machine in about 90 seconds and this new host in around 6 minutes to eliminate any problems with the iSCSI connection, I added a new LUN and directly accessed it from the new host and I was working at around 300MB/s so no problem there. I also tested the connection between the other hosts and the new one and network is working fine there too. to eliminate problems in HyperV, I copied the machine to the local disk of the new host and it loaded in less than 20 seconds. now is the point were things get a lot stranger: in my tests I tried installing a fresh windows guest machine to the CSV from the new host. I noticed that while the fresh windows was installing, my test guest was loading in less than 90 seconds even on the new host (I repeated this a few times). If I paused the fresh install guest and tried loading the test guest again it loaded in 6 minutes. and again after I resumed the guest installation the test guest loaded fast. after the fresh windows was also loaded, I ran tests loading the fresh window and my test machine. each one of them loaded in about 5 minutes when I tried loading them separately. however when I started both of them in the same time they both loaded in around 2.5 minutes it seems that the iSCSI disk access is only working if it is under some load (although I never got to above 10% utilization according to the task manager) does anyone have any idea what could be the problem?

  Read the article

• Make a Drive Image Using an Ubuntu Live CD

  - by Trevor Bekolay

  Cloning a hard drive is useful, but what if you have to make several copies, or you just want to make a complete backup of a hard drive? Drive images let you put everything, and we mean everything, from your hard drive in one big file. With an Ubuntu Live CD, this is a simple process – the versatile tool dd can do this for us right out of the box. We’ve used dd to clone a hard drive before. Making a drive image is very similar, except instead of copying data from one hard drive to another, we copy from a hard drive to a file. Drive images are more flexible, as you can do what you please with the data once you’ve pulled it off the source drive. Your drive image is going to be a big file, depending on the size of your source drive – dd will copy every bit of it, even if there’s only one tiny file stored on the whole hard drive. So, to start, make sure you have a device connected to your computer that will be large enough to hold the drive image. Some ideas for places to store the drive image, and how to connect to them in an Ubuntu Live CD, can be found at this previous Live CD article. In this article, we’re going to make an image of a 1GB drive, and store it on another hard drive in the same PC. Note: always be cautious when using dd, as it’s very easy to completely wipe out a drive, as we will show later in this article. Creating a Drive Image Boot up into the Ubuntu Live CD environment. Since we’re going to store the drive image on a local hard drive, we first have to mount it. Click on Places and then the location that you want to store the image on – in our case, a 136GB internal drive. Open a terminal window (Applications > Accessories > Terminal) and navigate to the newly mounted drive. All mounted drives should be in /media, so we’ll use the command cd /media and then type the first few letters of our difficult-to-type drive, press tab to auto-complete the name, and switch to that directory. If you wish to place the drive image in a specific folder, then navigate to it now. We’ll just place our drive image in the root of our mounted drive. The next step is to determine the identifier for the drive you want to make an image of. In the terminal window, type in the command sudo fdisk -l Our 1GB drive is /dev/sda, so we make a note of that. Now we’ll use dd to make the image. The invocation is sudo dd if=/dev/sda of=./OldHD.img This means that we want to copy from the input file (“if”) /dev/sda (our source drive) to the output file (“of”) OldHD.img, which is located in the current working directory (that’s the “.” portion of the “of” string). It takes some time, but our image has been created…Let’s test to make sure it works. Drive Image Testing: Wiping the Drive Another interesting thing that dd can do is totally wipe out the data on a drive (a process we’ve covered before). The command for that is sudo dd if=/dev/urandom of=/dev/sda This takes some random data as input, and outputs it to our drive, /dev/sda. If we examine the drive now using sudo fdisk –l, we can see that the drive is, indeed, wiped. Drive Image Testing: Restoring the Drive Image We can restore our drive image with a call to dd that’s very similar to how we created the image. The only difference is that the image is going to be out input file, and the drive now our output file. The exact invocation is sudo dd if=./OldHD.img of=/dev/sda It takes a while, but when it’s finished, we can confirm with sudo fdisk –l that our drive is back to the way it used to be! Conclusion There are a lots of reasons to create a drive image, with backup being the most obvious. Fortunately, with dd creating a drive image only takes one line in a terminal window – if you’ve got an Ubuntu Live CD handy! Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDCreate a Bootable Ubuntu USB Flash Drive the Easy WayHow to Browse Without a Trace with an Ubuntu Live CDWipe, Delete, and Securely Destroy Your Hard Drive’s Data the Easy WayClone a Hard Drive Using an Ubuntu Live CD TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Microsoft Office Web Apps Guide Know if Someone Accessed Your Facebook Account Shop for Music with Windows Media Player 12 Access Free Documentaries at BBC Documentaries Rent Cameras In Bulk At CameraRenter Download Songs From MySpace

  Read the article

• Delete merge history in a branch in TFS

  - by JMarsch

  Suppose I have a main branch and a dev branch. Suppose I merge some stuff from dev into main. I check in the merge Now I decide "whoops, the dev branch wasn't really ready for me to merge into main yet." I want to tell TFS: remove that change set from main and forget that the merge ever happened. Rolling back the changeset is easy enough -- I can use the TFS powertools ROLLBACK command. on the Main branch (with the /changeset /recursive flags) However, I will get a warning from the rollback that the merge history for the files has not been deleted. Effect: Later, when dev is ready to be merged into main, the changes in the files that were rolled back previously are NOT merged into Main (this is because TFS "thinks" that those merges are already done. My goal: When I rollback, make TFS remove the merge history so that when I merge dev into main later on, everything merges. How can I do that? BTW: I'm using TFS 2008 SP1

  Read the article

• Recovering from apt-get upgrade gone wrong due to a full disk

  - by Peter

  I was performing an apt-get upgrade on an Ubuntu 12.04.5 LTS box that hadn't been updated in a little while and the upgrade failed due to 'No space left on device'. After a little while I worked out space meant inodes and I have freed some up but unfortunately things have been left something askew. I have tried manually installing the old versions of packages mentioned using dpkg -i but that doesn't help. I have tried apt-get upgrade and apt-get -f install to no avail. Results are below. Any ideas how to fix things up? FIXED: Installing the earlier versions again manually via dpkg -i and then apt-get -f install has done the trick. Not sure why this didn't work the first time. The packages in question are listed below but they will presumably vary. libssl1.0.0_1.0.1-4ubuntu5.14_i386.deb linux-headers-3.2.0-64-generic-pae_3.2.0-64.97_i386.deb linux-image-generic-pae_3.2.0.64.76_i386.deb linux-headers-3.2.0-64_3.2.0-64.97_all.deb linux-headers-generic-pae_3.2.0.64.76_i386.deb root@unlinked:/tmp# apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done You might want to run ‘apt-get -f install’ to correct these. The following packages have unmet dependencies. libssl-dev : Depends: libssl1.0.0 (= 1.0.1-4ubuntu5.14) but 1.0.1-4ubuntu5.17 is installed linux-generic-pae : Depends: linux-image-generic-pae (= 3.2.0.64.76) but 3.2.0.67.79 is installed Depends: linux-headers-generic-pae (= 3.2.0.64.76) but 3.2.0.67.79 is installed E: Unmet dependencies. Try using -f. root@unlinked:/tmp# apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: linux-headers-3.2.0-43-generic-pae linux-headers-3.2.0-38-generic-pae linux-headers-3.2.0-41-generic-pae linux-headers-3.2.0-36-generic-pae linux-headers-3.2.0-63-generic-pae linux-headers-3.2.0-58-generic-pae linux-headers-3.2.0-60-generic-pae linux-headers-3.2.0-55-generic-pae linux-headers-3.2.0-40 linux-headers-3.2.0-41 linux-headers-3.2.0-36 linux-headers-3.2.0-37 linux-headers-3.2.0-43 linux-headers-3.2.0-38 linux-headers-3.2.0-44 linux-headers-3.2.0-39 linux-headers-3.2.0-45 linux-headers-3.2.0-51 linux-headers-3.2.0-52 linux-headers-3.2.0-53 linux-headers-3.2.0-48 linux-headers-3.2.0-54 linux-headers-3.2.0-60 linux-headers-3.2.0-55 linux-headers-3.2.0-61 linux-headers-3.2.0-56 linux-headers-3.2.0-57 linux-headers-3.2.0-63 linux-headers-3.2.0-58 linux-headers-3.2.0-59 linux-headers-3.2.0-52-generic-pae linux-headers-3.2.0-44-generic-pae linux-headers-3.2.0-39-generic-pae linux-headers-3.2.0-37-generic-pae linux-headers-3.2.0-59-generic-pae linux-headers-3.2.0-61-generic-pae linux-headers-3.2.0-56-generic-pae linux-headers-3.2.0-53-generic-pae linux-headers-3.2.0-48-generic-pae linux-headers-3.2.0-45-generic-pae linux-headers-3.2.0-40-generic-pae linux-headers-3.2.0-57-generic-pae linux-headers-3.2.0-54-generic-pae linux-headers-3.2.0-51-generic-pae Use 'apt-get autoremove' to remove them. The following extra packages will be installed: libssl-dev linux-generic-pae The following packages will be upgraded: libssl-dev linux-generic-pae 2 to upgrade, 0 to newly install, 0 to remove and 0 not to upgrade. 2 not fully installed or removed. Need to get 0 B/1,427 kB of archives. After this operation, 1,024 B of additional disk space will be used. Do you want to continue [Y/n]? y dpkg: dependency problems prevent configuration of libssl-dev: libssl-dev depends on libssl1.0.0 (= 1.0.1-4ubuntu5.14); however: Version of libssl1.0.0 on system is 1.0.1-4ubuntu5.17. dpkg: error processing libssl-dev (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates it's a follow-up error from a previous failure. dpkg: dependency problems prevent configuration of linux-generic-pae: linux-generic-pae depends on linux-image-generic-pae (= 3.2.0.64.76); however: Version of linux-image-generic-pae on system is 3.2.0.67.79. linux-generic-pae depends on linux-headers-generic-pae (= 3.2.0.64.76); however: Version of linux-headers-generic-pae on system is 3.2.0.67.79. dpkg: error processing linux-generic-pae (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates it's a follow-up error from a previous failure. Errors were encountered while processing: libssl-dev linux-generic-pae E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• DVD not detected?

  - by Benjamin

  As i insert a DVD in my drive (on a laptop) using Kubuntu 12.04, the DVD is not detected. The drive takes the DVD, I can hear it munching on it for a while, and then nothing. Even ejecting the DVD becomes a hassle, I need to do that at boot time otherwise the OS won't allow me to eject. Kubuntu 12.04 used to read and mount the same DVDs just fine a week ago. Edit: since I am able to boot from CD, can I safely assume the issue is not a hardware issue? How can I fix this? wodim --devices returns: wodim: Overview of accessible drives (1 found) : ------------------------------------------------------------------------- 0 dev='/dev/sg1' rwrw-- : 'Optiarc' 'DVD+-RW AD-7640A' ------------------------------------------------------------------------- sudo lshw -class disk returns: *-cdrom description: DVD-RAM writer product: DVD+-RW AD-7640A vendor: Optiarc physical id: 0.0.0 bus info: scsi@3:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/dvdrw2 logical name: /dev/sr0 version: JD06 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=open lspci returns: 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c) 00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3) 00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 03) 00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03) 06:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:05.0 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) 08:05.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02) 08:05.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) and lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0c45:63e0 Microdia Sonix Integrated Webcam Bus 003 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader The /etc/modprobe.d/blacklist.conf contains: # This file lists those modules which we don't want to be loaded by # alias expansion, usually so some other driver will be loaded for the # device instead. # evbug is a debug tool that should be loaded explicitly blacklist evbug # these drivers are very simple, the HID drivers are usually preferred blacklist usbmouse blacklist usbkbd # replaced by e100 blacklist eepro100 # replaced by tulip blacklist de4x5 # causes no end of confusion by creating unexpected network interfaces blacklist eth1394 # snd_intel8x0m can interfere with snd_intel8x0, doesn't seem to support much # hardware on its own (Ubuntu bug #2011, #6810) blacklist snd_intel8x0m # Conflicts with dvb driver (which is better for handling this device) blacklist snd_aw2 # causes failure to suspend on HP compaq nc6000 (Ubuntu: #10306) blacklist i2c_i801 # replaced by p54pci blacklist prism54 # replaced by b43 and ssb. blacklist bcm43xx # most apps now use garmin usb driver directly (Ubuntu: #114565) blacklist garmin_gps # replaced by asus-laptop (Ubuntu: #184721) blacklist asus_acpi # low-quality, just noise when being used for sound playback, causes # hangs at desktop session start (Ubuntu: #246969) blacklist snd_pcsp # ugly and loud noise, getting on everyone's nerves; this should be done by a # nice pulseaudio bing (Ubuntu: #77010) blacklist pcspkr # EDAC driver for amd76x clashes with the agp driver preventing the aperture # from being initialised (Ubuntu: #297750). Blacklist so that the driver # continues to build and is installable for the few cases where its # really needed. blacklist amd76x_edac

  Read the article

• Git exclude a commit in a branch

  - by becomingGuru

  I have a commit, I have stored in a branch, because this should go only to a specific box. I have merged it to the branch master, but not the branch dev, that I use locally. Now, by mistake I merged master to dev and that introduced this commit to dev. I know can git revert sha, to branch dev; but since this is going to introduce a commit that undoes that commit (I am guessing, I haven't exactly tried this), when I merge master, will this commit be undone too? If so, how do I undo this commit only from the branch dev. And oh, git reset HEAD^1 --hard is not an option because there are other commits on master, after the un-needed commit. If reset back again and apply is the only option, then how do I only merge those extra commits from master other than the un-needed commit. Thanks in advance!

  Read the article

• git strategy to have a set of commits limited to a particular branch

  - by becomingGuru

  I need to merge between dev and master frequently. I also have a commit that I need to apply to dev only, for things to work locally. Earlier I only merged from dev to master, so I had a branch production_changes that contained the "undo commit" of the dev special commit. and from the master, I merged this. Used to work fine. Now each time I merge from dev to master and vice versa, I am having to cherry-pick and apply the same commit again and again :(. Which is UGLY. What strategy can I adapt so that I can seamlessly merge between 2 branches, yet retain some of the changes only on one of those branches?

  Read the article

• ./configure : /bin/sh^M : bad interpreter

  - by Vineeth

  Hello there, I've been trying to install lpng142 on my fed 12 system. Seems like a problem to me. I get this error [root@localhost lpng142]# ./configure bash: ./configure: /bin/sh^M: bad interpreter: No such file or directory [root@localhost lpng142]# How do I fix this? and for more details, I shall include the /etc/fstub file details here # # /etc/fstab # Created by anaconda on Wed May 26 18:12:05 2010 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/VolGroup-lv_root / ext4 defaults 1 1 UUID=ce67cf79-22c3-45d4-8374-bd0075617cc8 /boot ext4 defaults 1 2 /dev/mapper/VolGroup-lv_swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 [root@localhost etc]# Help, please

  Read the article

• Migrating Virtual Iron guest to Oracle VM 3.x

  - by scoter

  As stated on the official site, Oracle in 2009, acquired a provider of server virtualization management software named Virtual Iron; you can find all the acquisition details at this link. Into the FAQ on the official site you can also view that, for the future, Oracle plans to fully integrate Virtual Iron technology into Oracle VM products, and any enhancements will be delivered as a part of the combined solution; this is what is going on with Oracle VM 3.x. So, customers started asking us to migrate Virtual Iron guests to Oracle VM. IMPORTANT: This procedure needs a dedicated OVM-Server with no-guests running on top; be careful while execute this procedure on production environments. In these little steps you will find how-to migrate, as fast as possible, your guests between VI ( Virtual Iron ) and Oracle VM; keep in mind that OracleVM has a built-in P2V utility ( Official Documentation )  that you can use to migrate guests between VI and Oracle VM. Concepts: VI repositories.  On VI we have the same "repository" concept as in Oracle VM; the difference between these two products is that VI use a raw-lun as repository ( instead of using ocfs2 and its capabilities, like ref-links ). The VI "raw-lun" repository, with a pure operating-system perspective, may be presented as in this picture: Infact on this "raw-lun" VI create an LVM2 volume-group. The VI "raw-lun" repository, with an hypervisor perspective, may be presented as in this picture: So, the relationships are: LVM2-Volume-Group <-> VI Repository LVM2-Logical-Volume <-> VI guest virtual-disk The first step is to present the VI repository ( raw-lun ) to your dedicated OVM-Server. Prepare dedicated OVM-Server On the OVM-Server ( OVS ) you need to discover new lun and, after that, discover volume-group and logical-volumes containted in VI repository; due to default OVS configuration you need to edit lvm2 configuration file: /etc/lvm/lvm.conf     # By default for OVS we restrict every block device:     # filter = [ "r/.*/" ] and comment the line starting with "filter" as above. Now you have to discover the raw-lun presented and, next, activate volume-group and logical-volumes: #!/bin/bash for HOST in `ls /sys/class/scsi_host`;do echo '- - -' > /sys/class/scsi_host/$HOST/scan; done CPATH=`pwd` cd /dev for DEVICE in `ls sd[a-z] sd?[a-z]`;do echo '1' > /sys/block/$DEVICE/device/rescan; done cd $CPATH cd /dev/mapper for PARTITION in `ls *[a-z] *?[a-z]`;do partprobe /dev/mapper/$PARTITION; done cd $CPATH vgchange -a yAfter that you will see a new device:[root@ovs01 ~]# cd /dev/6000F4B00000000000210135bef64994[root@ovs01 6000F4B00000000000210135bef64994]# ls -l 6000F4B0000000000061013* lrwxrwxrwx 1 root root 77 Oct 29 10:50 6000F4B00000000000610135c3a0b8cb -> /dev/mapper/6000F4B00000000000210135bef64994-6000F4B00000000000610135c3a0b8cb By your OVM-Manager create a guest server with the same definition as on VI:same core number as VI source guestsame memory as VI source guestsame number of disks as VI source guest ( you can create OVS virtual disk with a small size of 1GB because the "clone" will, eventually, extend the size of your new virtual disks )Summarizing:source-virtual-disk path ( VI ):/dev/mapper/6000F4B00000000000210135bef64994-6000F4B00000000000610135c3a0b8cbdest-virtual-disk path ( OVS ):/OVS/Repositories/0004fb00000300006cfeb81c12f12f00/VirtualDisks/0004fb000012000055e0fc4c5c8a35ee.img ** ** = to identify your virtual disk you have verify its name under the "vm.cfg" file of your new guest.Clone VI virtual-disk to OVS virtual-diskdd if=/dev/mapper/6000F4B00000000000210135bef64994-6000F4B00000000000610135c3a0b8cb of=/OVS/Repositories/0004fb00000300006cfeb81c12f12f00/VirtualDisks/0004fb000012000055e0fc4c5c8a35ee.img Clean unsupported parameters and changes on OVS.1. Restore original /etc/lvm/lvm.conf    # By default for OVS we restrict every block device:     filter = [ "r/.*/" ]    and uncomment the line starting with "filter" as above.2. Force-stop lvm2-monitor service  # service lvm2-monitor force-stop 3. Restore original /etc/lvm directories ( archive, backup and cache )  # cd /etc/lvm  # rm -fr archive backup cache; mkdir archive backup cache4. Reboot OVSRefresh OVS repository and start your guest.By OracleVM Manager refresh your repository:By OracleVM Manager start your "migrated" guest: Comments and corrections are welcome.  Simon COTER 

  Read the article

• Resize the /var directory in redhat enterprise edition 4

  - by Sri

  I am running NDB mysql. the log files fills up the /var directory. therefore i cant start the ndbd service now. as a temporary fix, i have deleted the log files and again working fine. but again the log files fill up the /var directory. i got plenty of space in other partition. therefore i would like to swap the partition from one directory to /var. here if my input from df -h Filesystem Type Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 ext3 54G 2.9G 49G 6% / /dev/cciss/c0d0p1 ext3 99M 14M 81M 14% /boot none tmpfs 1013M 0 1013M 0% /dev/shm /dev/cciss/c0d0p2 ext3 9.7G 9.7G 0 100% /var there are plenty of space in /dev/mapper/VolGroup00-LogVol00. Therefore i will like to swap 10 G space from this directory to /var. could you please help me out to solve this problem?

  Read the article

• install CakePHP on Mac osx: apache problems

  - by ed209

  First time cake user and I'm having real apache problems. For some reason the .htaccess is trying to find File does not exist: /Library/WebServer/Documents/Users but there is no such directory as Users. I have tried setting up the following also: /etc/apache2/extra/httpd-vhosts.conf <VirtualHost *:80 > DocumentRoot "/Users/username/Sites/mysite/app/webroot" ServerName mysite.dev ServerAlias www.mysite.dev mysite.dev *.mysite.dev <Directory "/Users/username/Sites/mysite/app/webroot"> Options Indexes FollowSymLinks AllowOverride All </Directory> </VirtualHost> /etc/hosts 127.0.0.1 mysite.dev /etc/apache2/users/username.conf <Directory "/Users/username/Sites/"> Options Indexes MultiViews FollowSymlinks AllowOverride All Order allow,deny Allow from all </Directory> That also hasn't worked, but with a different error Failed opening required 'cake/libs/cache/file.php' Although I'd rather not use virtual hosts, and just run it off localhost

  Read the article

• Need to know who is hogging my bandwidth?

  - by Dev

  I have an ethernet connection to my iMac and with Internet sharing I am broadcasting the wireless network from my mac rather than using a wireless router. I use it to connect other devices wirelessly to the internet. But this makes all the traffic flow through my iMac. I wanted a way to analyze the traffic so that I know what connected devices are hogging the bandwidth at a given time and from which websites? I installed wireshark for mac and played around a little but it seems like an overkill when you first look at it. Can someone please help with few instructions to get what I need or any other way other than using wireshark? Thanks Dev.

  Read the article

• Linux C: "Interactive session" with separate read and write named pipes?

  - by ~sd-imi

  Hi all, I am trying to work with "Introduction to Interprocess Communication Using Named Pipes - Full-Duplex Communication Using Named Pipes", http://developers.sun.com/solaris/articles/named_pipes.html#5 ; in particular fd_server.c (included below for reference) Here is my info and compile line: :~$ cat /etc/issue Ubuntu 10.04 LTS \n \l :~$ gcc --version gcc (Ubuntu 4.4.3-4ubuntu5) 4.4.3 :~$ gcc fd_server.c -o fd_server fd_server.c creates two named pipes, one for reading and one for writing. What one can do, is: in one terminal, run the server and read (through cat) its write pipe: :~$ ./fd_server & 2/dev/null [1] 11354 :~$ cat /tmp/np2 and in another, write (using echo) to server's read pipe: :~$ echo "heeellloooo" /tmp/np1 going back to first terminal, one can see: :~$ cat /tmp/np2 HEEELLLOOOO 0[1]+ Exit 13 ./fd_server 2 /dev/null What I would like to do, is make sort of a "interactive" (or "shell"-like) session; that is, the server is run as usual, but instead of running "cat" and "echo", I'd like to use something akin to screen. What I mean by that, is that screen can be called like screen /dev/ttyS0 38400, and then it makes a sort of a interactive session, where what is typed in terminal is passed to /dev/ttyS0, and its response is written to terminal. Now, of course, I cannot use screen, because in my case the program has two separate nodes, and as far as I can tell, screen can refer to only one. How would one go about to achieve this sort of "interactive" session in this context (with two separate read/write pipes)? Thanks, Cheers! Code below: #include <stdio.h> #include <errno.h> #include <ctype.h> #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> //#include <fullduplex.h> /* For name of the named-pipe */ #define NP1 "/tmp/np1" #define NP2 "/tmp/np2" #define MAX_BUF_SIZE 255 #include <stdlib.h> //exit #include <string.h> //strlen int main(int argc, char *argv[]) { int rdfd, wrfd, ret_val, count, numread; char buf[MAX_BUF_SIZE]; /* Create the first named - pipe */ ret_val = mkfifo(NP1, 0666); if ((ret_val == -1) && (errno != EEXIST)) { perror("Error creating the named pipe"); exit (1); } ret_val = mkfifo(NP2, 0666); if ((ret_val == -1) && (errno != EEXIST)) { perror("Error creating the named pipe"); exit (1); } /* Open the first named pipe for reading */ rdfd = open(NP1, O_RDONLY); /* Open the second named pipe for writing */ wrfd = open(NP2, O_WRONLY); /* Read from the first pipe */ numread = read(rdfd, buf, MAX_BUF_SIZE); buf[numread] = '0'; fprintf(stderr, "Full Duplex Server : Read From the pipe : %sn", buf); /* Convert to the string to upper case */ count = 0; while (count < numread) { buf[count] = toupper(buf[count]); count++; } /* * Write the converted string back to the second * pipe */ write(wrfd, buf, strlen(buf)); } Edit: Right, just to clarify - it seems I found a document discussing something very similar, it is http://en.wikibooks.org/wiki/Serial_Programming/Serial_Linux#Configuration_with_stty - a modification of the script there ("For example, the following script configures the device and starts a background process for copying all received data from the serial device to standard output...") for the above program is below: # stty raw # ( ./fd_server 2>/dev/null; )& bgPidS=$! ( cat < /tmp/np2 ; )& bgPid=$! # Read commands from user, send them to device echo $(kill -0 $bgPidS 2>/dev/null ; echo $?) while [ "$(kill -0 $bgPidS 2>/dev/null ; echo $?)" -eq "0" ] && read cmd; do # redirect debug msgs to stderr, as here we're redirected to /tmp/np1 echo "$? - $bgPidS - $bgPid" >&2 echo "$cmd" echo -e "\nproc: $(kill -0 $bgPidS 2>/dev/null ; echo $?)" >&2 done >/tmp/np1 echo OUT # Terminate background read process - if they still exist if [ "$(kill -0 $bgPid 2>/dev/null ; echo $?)" -eq "0" ] ; then kill $bgPid fi if [ "$(kill -0 $bgPidS 2>/dev/null ; echo $?)" -eq "0" ] ; then kill $bgPidS fi # stty cooked So, saving the script as say starter.sh and calling it, results with the following session: $ ./starter.sh 0 i'm typing here and pressing [enter] at end 0 - 13496 - 13497 I'M TYPING HERE AND PRESSING [ENTER] AT END 0~?.N=?(?~? ?????}????@??????~? [garble] proc: 0 OUT which is what I'd call for "interactive session" (ignoring the debug statements) - server waits for me to enter a command; it gives its output after it receives a command (and as in this case it exits after first command, so does the starter script as well). Except that, I'd like to not have buffered input, but sent character by character (meaning the above session should exit after first key press, and print out a single letter only - which is what I expected stty raw would help with, but it doesn't: it just kills reaction to both Enter and Ctrl-C :) ) I was just wandering if there already is an existing command (akin to screen in respect to serial devices, I guess) that would accept two such named pipes as arguments, and establish a "terminal" or "shell" like session through them; or would I have to use scripts as above and/or program own 'client' that will behave as a terminal..

  Read the article

• SOLVED - UBIFS partition mounting at startup [closed]

  - by Bartlomiej Grzeskowiak

  [SOLVED] - add ubi.mtd=volume_name to bootargs in uboot I want to mount UBIFS partition via /etc/fstab at startup. I created UBIFS and Volume: # ubiformat /dev/mtdX # ubiattach -p /dev/mtdX # ubimkvol /dev/ubi0 -N volume_name -s 64MiB # ubiupdatevol /dev/ubi0_0 /path/to/ubifs.img # mount -t ubifs ubi0:volume_name /mount/point but after reboot this line in etc/fstab doesn't work: ubi0:volume_name /mnt/user ubifs defaults 0 0 There is no fs mounted in /mnt/user. Also when I try to call mount -a: mount: mounting ubi0:volume_name on /mnt/user failed: No such device There are no ubi0,ubi0_0 in /dev. I also don't see any UBI calls in dmesg like here: UBIFS boot error

  Read the article

• Problems encountered in changing a CRichEditCtrl selection color.

  - by dev ray

  I have written the following code after creating the CRichEditCtrl // 06112010 : The following code was added to highlight the textselection in black color instead of the default blue color of CRichEditCtrl. - 1311 { m_EditControl.SetSel(0,100); CHARFORMAT2 cf1; cf1.cbSize = sizeof(CHARFORMAT2); m_EditControl.GetSelectionCharFormat(cf1); cf1.dwMask = CFM_BACKCOLOR ; cf1.dwEffects &= ~CFE_AUTOBACKCOLOR; cf1.crBackColor = RGB(0,0,0); m_EditControl.SetSelectionCharFormat(cf1); m_EditControl.Invalidate(); } After this I am adding text, but the selection still comes in blue color instead of Black. Could someone please tell me what I am doing wrong?? Thanks, DeV

  Read the article

• Git workflow idea to push an unfinished local branch to remote for backup purposes

  - by Zubin

  Say I'm currently working on a new feature which I've branched off of the 'dev' branch and I've been working for several days and it's not yet ready to be merged with 'dev' and pushed. Although I have made several commits and have been pulling changes to dev and then merging dev into my feature branch to keep myself updated. Here's my question. Is it a good idea to push my feature branch to a new branch (with the same name as my local branch) onto origin (say GitHub) just for back-up purposes and later on when it's merged into 'dev' and/or 'master' delete it from origin.

  Read the article

• .net (winforms, not asp) multi-server deployment

  - by poiuyttr

  I have a small .NET WinForms application, and couple of linux servers, DEV and CL1,CL2..CLN (DEV is development server and CL* are servers which belons to our clients, they are in private networks and it's a kind of production servers) I want an update mechanism so that (1) i develop a new version and publish it to a DEV (2) users of DEV-server install latest version from DEV (3) users of CL2 (employees of client2) install stable version from CL-2 directly (4) application checks for updates using server it was installed from (so, if it was installed from CL-2, it should check CL-2 for updates) (5) i should be able to propogate the update to a selected CL-server (using just file copy & maybe sed; not republishing), if i want that (and if i don't, that CL-server will have an old version until manually i update it) I tried to use clickonce, but looks like it meets only first two requirements. What should i do?

  Read the article

• CodeIgniter won't run in a subdirectory

  - by Tim Piele

  I have a CodeIgniter install running in our root web directory that I copied into a subdirectory called /dev... I edited the config/config.php file to reflect the change so it is now like this: $config['base_url'] = 'http://mysite.com/dev'; $config['sbase_url'] = 'https://mysite.com/dev'; $config['default_email'] = '[email protected]'; $config['site_url'] = 'http://mysite.com/dev'; This is my .htaccess file: <IfModule mod_rewrite.c> RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ index.php/$1 [L] </IfModule> When I hover over any links on the site they are correct, for example the contact us page link reads www.mysite.com/dev/contact but when I click any of the links I get a 404 error... Is there something common I am missing?

  Read the article

• Python Coding standards vs. productivity

  - by Shroatmeister

  I work for a large humanitarian organisation, on a project building software that could help save lives in emergencies by speeding up the distribution of food. Many NGOs desperately need our software and we are weeks behind schedule. One thing that worries me in this project is what I think is an excessive focus on coding standards. We write in python/django and use a version of PEP0008, with various modifications e.g. line lengths can go up to 160 chars and all lines should go that long if possible, no blank lines between imports, line wrapping rules that apply only to certain kinds of classes, lots of templates that we must use, even if they aren't the best way to solve a problem etc. etc. One core dev spent a week rewriting a major part of the system to meet the then new coding standards, throwing away several suites of tests in the process, as the rewrite meant they were 'invalid'. We spent two weeks rewriting all the functionality that was lost, and fixing bugs. He is the lead dev and his word carries weight, so he has convinced the project manager that these standards are necessary. The junior devs do as they are told. I sense that the project manager has a strong feeling of cognitive dissonance about all this but nevertheless agrees with it vehemently as he feels unsure what else to do. Today I got in serious trouble because I had forgotten to put some spaces after commas in a keyword argument. I was literally shouted at by two other devs and the project manager during a Skype call. Personally I think coding standards are important but also think that we are wasting a lot of time obsessing with them, and when I verbalized this it provoked rage. I'm seen as a troublemaker in the team, a team that is looking for scapegoats for its failings. Since the introduction of the coding standards, the team's productivity has measurably plummeted, however this only reinforces the obsession, i.e. the lead dev simply blames our non-adherence to standards for the lack of progress. He believes that we can't read each other's code if we don't adhere to the conventions. This is starting to turn sticky. Now I am trying to modify various scripts, autopep8, pep8ify and PythonTidy to try to match the conventions. We also run pep8 against source code but there are so many implicit amendments to our standard that it's hard to track them all. The lead dev simple picks faults that the pep8 script doesn't pick up and shouts at us in the next stand-up meeting. Every week there are new additions to the coding standards that force us to rewrite existing, working, tested code. Thank heavens we still have tests, (I reverted some commits and fixed a bunch of the ones he removed). All the while there is increasing pressure to meet the deadline. I believe a fundamental issue is that the lead dev and another core dev refuse to trust other developers to do their job. But how to deal with that? We can't do our job because we are too busy rewriting everything. I've never encountered this dynamic in a software engineering team. Am I wrong to question their adherence to coding standards? Has anyone else experienced a similar situation and how have they dealt with it successfully? (I'm not looking for a discussion just actual solutions people have found)

  Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >