Search Results

Search found 18775 results on 751 pages for 'old hardware'.

Page 70/751 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

  • Are there open source Linux drivers for the Panda Wifi USB adapter?

    - by Zifre
    I'm looking for a wireless adapter for my new PC. My requirements are: it supports 802.11n it is cheap (under 30 USD) it has good, open source Linux drivers (will work "out of the box") preferably USB, but PCI is okay too I found the Panda Wifi (b/g/n) 150Mbps Wireless-N (802.11n) USB Adapter. It says there is Linux support. However, I want to make sure there are open source drivers included with the Linux kernel. Does anyone know what the chipset for this adapter is? What driver it would use?

    Read the article

  • LSI MegaRAID LINUX got Optimal after degradation but strange POST message

    - by kesrut
    Linux server box with LSI MegaRAID controller got degraded. But after some time RAID status changed to Optimal. Adapter 0 -- Virtual Drive Information: Virtual Drive: 0 (Target Id: 0) Name : RAID Level : Primary-1, Secondary-0, RAID Level Qualifier-0 Size : 2.727 TB Mirror Data : 2.727 TB State : Optimal Strip Size : 256 KB Number Of Drives per span:2 Span Depth : 3 Default Cache Policy: WriteBack, ReadAdaptive, Cached, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Cached, No Write Cache if Bad BBU Default Access Policy: Read/Write Current Access Policy: Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Is VD Cached: No But now I'm getting RAID BIOS POST message: Your battery is either charging, bad or missing, and you have VDs configured for write-back mode. Because the battery is not currently usable, these VDs willl actually run in write-through mode until the battery is fully charged or replaced if it is bad or missing. (Image: http://cl.ly/image/1h1O093b1i2d) So may it be battery issue caused problem ? I get information about battery: BatteryType: iBBU Voltage: 4001 mV Current: 0 mA Temperature: 22 C Battery State : Operational BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : No Periodic Learn Required : No Transparent Learn : No No space to cache offload : No Pack is about to fail & should be replaced : No Cache Offload premium feature required : No Module microcode update required : No Where can be problem ? I'm disabled alarms, but get them if enabled. But don't know how find root of problem.

    Read the article

  • Zero-channel RAID for High Performance MySQL Server (IBM ServeRAID 8k) : Any Experience/Recommendati

    - by prs563
    We are getting this IBM rack mount server and it has this IBM ServeRAID8k storage controller with Zero-Channel RAID and 256MB battery backed cache. It can support RAID 10 which we need for our high performance MySQL server which will have 4 x 15000K RPM 300GB SAS HDD. This is mission-critical and we want as much bandwidth and performance. Is this a good card or should we replace with another IBM RAID card? IBM ServeRAID 8k SAS Controller option provides 256 MB of battery backed 533 MHz DDR2 standard power memory in a fixed mounting arrangement. The device attaches directly to IBM planar which can provide full RAID capability. Manufacturer IBM Manufacturer Part # 25R8064 Cost Central Item # 10025907 Product Description IBM ServeRAID 8k SAS - Storage controller (zero-channel RAID) - RAID 0, 1, 5, 6, 10, 1E Device Type Storage controller (zero-channel RAID) - plug-in module Buffer Size 256 MB Supported Devices Disk array (RAID) Max Storage Devices Qty 8 RAID Level RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 1E Manufacturer Warranty 1 year warranty

    Read the article

  • Computer has video artifacts after been exposed to rain

    - by Sadie
    My desktop now displays video artifacts after been exposed to rain. Only a very small amount of moisture went inside the case. The only place I noticed any water was on the CPU socket. I used a hair dryer and paper towels to wick any remaining moisture. When I boot the PC it loads it the OS, but there are large numbers of video artifacts. The artifacts appear symmetric if that helps. I am wondering what components I need to replace. I'd like to salvage what I can. My setup: AMD Athlon x3, Asus main board (AM2 socket), nVidia GT 430 PCIe, 8gb (4gb x2) DDR3

    Read the article

  • Intel D2500HN Atom D2500 Doesn't turn on

    - by David W
    I recently bought parts from Amazon to build an embedded PC, and have assembled everything. I have: Intel D2500HN Mini-ITX Motherboard Mini-Box Pico-PSU 80 M350 Universal Min-ITX Enclosure 2GB DDR3 Memory Kinamax AD-LCD12 LCD Monitors 12V 6A 72W AC Adapter Power Supply The motherboard gets a light (on the motherboard, not on the Pico-PSU) when I plug it into the power adapter. Furthermore, I see the power switch light come on when I press the power button. However, the display doesn't turn on, and it doesn't seem that the PC is actually turned on. Since I'm seeing these lights, I know that the motherboard is getting power. Furthermore, the display VGA port is embedded into the motherboard, so that's not the issue. I'm just trying to figure out what COULD be the issue aside from a faulty motherboard. I have a diagram of the D2500HN motherboard which labels everything, and have ensured that the power LED as well as the On/Off cables are plugged into the right spots, although to be sure I've tried flipping these two cables around, and also plugging 1 cable into the other cable's spot & vice-versa. Is there anything else you folks think I may be missing, or anything else I can do to try to troubleshoot this issue before sending the motherboard back?

    Read the article

  • Remap FN to another key

    - by MrValdez
    I got a keyboard (Logitech Wave, pictured below) which I'm very happy with. Unfortunately, the manufacturer has changed the button for right-click for a FN key. Is there any program to remap the FN key to something else?

    Read the article

  • Laptop screen brightness stuck

    - by Bart van Heukelom
    I can no longer adjust the brightness of my laptop screen, it's stuck at the lowest. In Linux, the brightness adjustment keys (Fn + F4/F5) still work, since a brightness popup shows and the meter bar changes, but it does this in a strange way. Starting at 100%, each successive press of the "lower brightness" button moves the bar to: 67% 50% 0% 26% 12% Or another random pattern like that. The problem is not Linux however, since I can't change the brightness from Windows (7) either. Where do I even begin to look? Since the problem does not seem be OS-specific, I've searched in the BIOS, but it has no option like that. How did this happen? I think it's been this way since when I lowered the brightness to 0%, then pressed the "lower brightness" key again. Not sure about that though.

    Read the article

  • Building a Media Center PC with Comcast Cable...?

    - by Rob
    Alright - so this might be a stupid question but I've never been all that much into TV. I currently have Comcast cable. I've just got the 'basic' 2-60 package or whatever; I've just always plugged the cable into the back of my TV. I've never had a cable box. Recently, Comcast has been pulling channels off of my line-up. Most recently, the stole the TV Guide channel from me. I'm told this is part of a push to get customers to switch to their digital line-up. But, I'm also told it requires some sort of digital receiver for each TV you've got. I don't want to buy a bunch of these digital receivers and I don't want to pay the monthly rental fee...but I have heard of how awesome media center PCs are and some really cool things they can do. And, I've got loads of PC parts sitting around. So, can someone guide me through this a bit? Are there computer video cards or TV tuners that are going to work with Comcast's digital cable? What kind of price range are we looking at?

    Read the article

  • Is the motherboard the cause of these errors?

    - by ianfuture
    Motherboard is : ASUS A7N8X-E Deluxe, Rev1.01, On start up get: "cmos checksum error - defaults loaded" error BIOS is reset everytime and can't boot to Windows off HDD. POST report is ok once I tell it there is no Floppy drive attached and not to seek it. The boot sequence starts then just as get to load windows safe mode options whole PC shuts down. BIOS is reset to defaults again. I've checked the battery and jumpers. Tried a known working battery. Changed Graphics card, changed memory, changed HD to one without an OS. Disconnected DVD drive. PSU is known to be ok. IN BIOS CPU is recognised correctly and memory is also recognised ok. So is it likely to be a bad motherboard or corrupted BIOS or something else? Thanks :)

    Read the article

  • Is my hard drive about to die?

    - by Hristo Deshev
    I have two hard drives set up as a RAID 1 array on my server (Linux, software RAID using mdadm) and one of them just got me this "present" in syslog: Nov 23 02:05:29 h2 kernel: [7305215.338153] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:29 h2 kernel: [7305215.338178] ata1.00: irq_stat 0x40000008 Nov 23 02:05:29 h2 kernel: [7305215.338197] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:29 h2 kernel: [7305215.338220] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:29 h2 kernel: [7305215.338221] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:29 h2 kernel: [7305215.338287] ata1.00: status: { DRDY ERR } Nov 23 02:05:29 h2 kernel: [7305215.338305] ata1.00: error: { UNC } Nov 23 02:05:29 h2 kernel: [7305215.358901] ata1.00: configured for UDMA/133 Nov 23 02:05:32 h2 kernel: [7305218.269054] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:32 h2 kernel: [7305218.269081] ata1.00: irq_stat 0x40000008 Nov 23 02:05:32 h2 kernel: [7305218.269101] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:32 h2 kernel: [7305218.269125] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:32 h2 kernel: [7305218.269126] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:32 h2 kernel: [7305218.269196] ata1.00: status: { DRDY ERR } Nov 23 02:05:32 h2 kernel: [7305218.269215] ata1.00: error: { UNC } Nov 23 02:05:32 h2 kernel: [7305218.341565] ata1.00: configured for UDMA/133 Nov 23 02:05:35 h2 kernel: [7305221.193342] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:35 h2 kernel: [7305221.193368] ata1.00: irq_stat 0x40000008 Nov 23 02:05:35 h2 kernel: [7305221.193386] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:35 h2 kernel: [7305221.193408] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:35 h2 kernel: [7305221.193409] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:35 h2 kernel: [7305221.193474] ata1.00: status: { DRDY ERR } Nov 23 02:05:35 h2 kernel: [7305221.193491] ata1.00: error: { UNC } Nov 23 02:05:35 h2 kernel: [7305221.388404] ata1.00: configured for UDMA/133 Nov 23 02:05:38 h2 kernel: [7305224.426316] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:38 h2 kernel: [7305224.426343] ata1.00: irq_stat 0x40000008 Nov 23 02:05:38 h2 kernel: [7305224.426363] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:38 h2 kernel: [7305224.426387] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:38 h2 kernel: [7305224.426388] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:38 h2 kernel: [7305224.426459] ata1.00: status: { DRDY ERR } Nov 23 02:05:38 h2 kernel: [7305224.426478] ata1.00: error: { UNC } Nov 23 02:05:38 h2 kernel: [7305224.498133] ata1.00: configured for UDMA/133 Nov 23 02:05:41 h2 kernel: [7305227.400583] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:41 h2 kernel: [7305227.400608] ata1.00: irq_stat 0x40000008 Nov 23 02:05:41 h2 kernel: [7305227.400627] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:41 h2 kernel: [7305227.400649] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:41 h2 kernel: [7305227.400650] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:41 h2 kernel: [7305227.400716] ata1.00: status: { DRDY ERR } Nov 23 02:05:41 h2 kernel: [7305227.400734] ata1.00: error: { UNC } Nov 23 02:05:41 h2 kernel: [7305227.472432] ata1.00: configured for UDMA/133 From what I read so far, I am not sure if read errors mean that a hard drive is dying on me (no write errors so far). I've had hard drive errors in the past and those always had errors about failing to write to specific sectors in the logs. Not this time. Should I be replacing the drive? Could something else be causing the problem? I've scheduled a smartctl -t long test that will finish in a couple of hours. I hope this will give me some more info.

    Read the article

  • How many users are "many users"?

    - by kemp
    I need to find a solution for a website which is struggling under load. The site gets ~500 simultaneous connections during peak time, and counts around 42k hits per day. It's a wordpress based site bridged with a vbulletin forum with a lot of contents and a fairly complex structure which makes intensive use of the database. I already implemented code level full page caching (without this the server just crashes), and configured all other caching directives as well as combining css files and the like to limit http requests as much as possible. I need to understand if there is more that can be done via software or if the load is just too much for the server to handle and it needs to be upgraded, because the server goes down occasionally during peak times. Can't access the server now, but it's a dedicated CentOS machine (I think 4GB ram, can't say what CPU) running apache/mysql. So back to the main question: how can I know when the users are just too many?

    Read the article

  • Bought a 1U server, now can't find rails

    - by Paul Tomblin
    I bought a 1U server used on eBay (a Supermicro motherboard, but branded "Asempra"), and I also bought a set of "Supermicro" rails, but unfortunately the rails didn't fit the server. The side of the server looks like: Can you tell me where I can find rails for this machine?

    Read the article

  • Thinkpad Motherboard Component List

    - by Nirmal
    I got an IBM Thinkpad R51 notebook and it's not working. When opened I found that an IC next to the battery has burnt. The worst part is that the IC number is no more present on it due to the burning. Where could I get the schematics of such motherboards? Will the schematics have the part number? Please help. Thank you.

    Read the article

  • Mutli-processor workstation as a workstation/server

    - by posdef
    I work in a research institute and a number of programs we use are computationally intensive (I actually wrote one of them). Right now we have one computer that is dedicated for one of these programs (with local accounts only, as in users physically sitting in front of that pc) and the other programs are run on individual workstations assigned to people. I have been looking around to common brands such as Dell and HP, for a some sort of a small/medium scale server, which can be used as a workhorse by sending tasks remotely. It appears as if there is nothing in between workstations with one 6-core processor and a bunch of extras (like fancy graphics etc) and rack mount servers with ridiculous amount of RAM and HDD expansion capabilities but still relatively little number of processors/cores. I wonder if what I am looking for is such a small niche product? Are there other solutions that I might not be aware of? Does anyone know of a multi proc- multi-core workstation/server that is still within the reasonable

    Read the article

  • Bare-metal virtualisation for the desktop

    - by Andrew Taylor
    Hi, Does anyone have any knowledge about bare-metal virtualisation products? I'm interested in building a new desktop machine for home, I've been looking at the Intel Quad Core processors and I'd like to put 8GB of RAM in there, but, it got me thinking about making the most out of the available resources. I thought if I could get a good 64bit machine, put some bare-metal virtualisation on, then have a primary system, I'd also be able to bring up some extra virtualised systems as and when I needed. I know most of the bare metal systems are designed for the server market, but, is there anything out there that works well for a desktop. What are the caveats? I presume I won't be able to make the most out of any video cards I could buy, what about just getting a decent screen resolution, will this be a problem? I run a single 24" screen. What about DVD/CD writing, is this possible? I'd like to re-rip my CD collection, I was hoping the quad 64Bit goodness would help me out with the encoding. I currently use a Mac and couldn't go back to windows so that leaves Linux, I was thinking a primary OS of ubuntu. Does this make a difference? Thanks Andrew

    Read the article

  • Performing mechanical movements using computer

    - by Vi
    How to make a computer (in particular, my laptop) to perform some mechanical movements without buying anything $5, soldering things inside computer or creating big sophisticated circuits? Traditionally CD-ROM tray is used to make computer do some movement IRL by, for example, SSH command, but in laptop tray is one-shot (unless manually reloaded) and also not very comfortable [mis]usage. Some assistance circuits can be in use too, but not complex. For example, there is a little motor that can work on USB power. Devices in my computer: DVD-ROM tray: one-time push. USB power: continuous power to the motor or LEDS or relay that turns on something powerful. Audio card. 3 outputs (modprobe alsa model=test can set Mic and Line-in as additional output). One controllable DC output (microphone) that can power up LED and some electronic (may be even mechanic?) relay. Also with sophisticated additional circuiting can control a lot of devices with a good precision. Both input and output support. Probably the most useful object in computer for radio ham. Modem. Don't know about this much, it doesn't work because of hsfmodem crashes kernel if memory is = 1GB. May be it's "pick up" and "hang up" can turn on and off power taken from USB port? Video card. VGA port? S-Video port? Will them be useful? Backlight. Tunable, but probably unuseful. CardBus (or some) slot. Nothing interesting for the task probably (is it?). AC adapter and battery. Probably nothing programmable here. /* My AC adapter already have additional jacks to connect extra devics */ Keyboard. No use. Touchpad. Good sensor (synclient -m 1), but no output. Various LEDs inside laptop. Probably too weak and requires soldering. Fans inside laptop. Poor control over them, requires soldering and dangerous to tinker. HDD (internal and external) that can be spin down and up (hdparm -Y, cat /dev/ubb). But connecting anything serially with it's power line makes HDD underpowered... And too complex. Is something are missed? Any ideas how to use described components? Any other ideas? May be there are easily available /* in developing countries */ cheap devices like "enhanced multimeters" that are controllable from computer and can provide configurable output and measure current and other things? Things to aid pushing many physical buttons with computer. Isn't this a simple idea and implementation and a lot of use in good hands?

    Read the article

  • Connect wired-only devices to a remote wireless access point?

    - by billpg
    Hi everyone. In building A, I have a Netgear wireless access point using WPA2. Works great, no problems. In building B, I have some devices that only have wired Ethernet ports. They can't see my access point. What I need is a gizmo that connects over-the-air to my access point in building A, talks WPA2, and converts the packets to and from a wired Ethernet port. Netgear-access-point in building A      (WPA2 WiFi) Wireless bridge device          <-- Looking for this.      (Cat5 ethernet) My devices in building B. I've looked for devices on Amazon, but the descriptions are infuriatingly unclear. It says it supports WPA2, but does it support it as a client? Grrr... Any recommendations please?

    Read the article

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • Max length of a USB Cable?

    - by Click Ok
    I want to use a very long USB cable to, for example, place a webcam in a different room. The max length that I found was 5 meters. What the max length of a USB cable and... What the max length that I can get using USB extension cables? Thanks in advance!

    Read the article

  • Computer wont POST after power outage

    - by aaron
    I had just turned my computer on and windows was loading when the power in my neighborhood went out. Normally, when I turn my computer on, the video card fan spins up, then slows down, POST and windows boots. Now, after the blackout, the video card fan spins fast and wont stop. Nothing is displayed on the monitor. The monitor does not detect that the video card is sending it signals, it just stays on standby. No POST or beep codes. This is what I have tried so far: My motherboard has 2 PCI express slots and I tried plugging the video card into both of them but that didn't fix anything. I have replaced the power supply, that didn't fix anything. I cleared the CMOS, that didn't fix anything. Does anyone have any idea of what could be wrong? Thanks!

    Read the article

  • Experience with AMCC 3ware 9650se raid cards? Ours seems dead

    - by antiduh
    We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated.

    Read the article

  • Scope of Mainframe Technologies Today?

    - by Vaibhav Bajpai
    I have been recently allocated to training in Mainframe Technologies at my company (where I am currently working as a Trainee). I am slated to learn DB2, JCL, CICS, and Cobol during the programme. I am from a C++ background, and curious how the community here feels of these technologies. I am also curious to know, how mainframe computers fit into today's computing scenario where distributed computing has taken over almost completely.

    Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >