Search Results

Search found 38282 results on 1532 pages for 'ubuntu 12 04'.

Page 70/1532 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

  • How can I upgrade to Lubuntu 14.04.1 withot a PAE kernel?

    - by Richard
    On my Dell Latitude D800 laptop, which has an old Pentium M without PAE support, I was able to successfully install Lubuntu 14.04 from the CD. When I try to upgrade, I get the error: PAE not enabled Your system uses a CPU that does not have PAE enabled. Ubuntu only supports non-PAE systems up to Ubuntu 12.04. To upgrade to a later version of Ubuntu, you must enable PAE (if this is possible) see: http://help.ubuntu.com/community/EnablingPAE I have seen the Communit Wiki page for PAE. The suggestion is to add forcepae to the command line options. When I do this, I get the same message. Moreover, dmesg does not indicate PAE was ever enabled. Is there anything else I can ry to get Lubuntu to upgrade correctly?

    Read the article

  • Fresh install on SSD with Ubuntu and Windows Vista, using whole disk encryption for Ubuntu

    - by nategator
    I would like to do a fresh install on a OCZ Vertex Plus R2 SSD 60GB drive I purchased on the cheap. Since the AES-encryption looks like it may not work optimally for this drive, I would like to set up a dual-boot to Windows Vista (the only Windows copy I have for clean install purposes) and Ubuntu 12.04 with the best encryption scheme possible. My plan is to have Windows around just in case I need to use a program that won't work with Wine and Ubuntu as my daily OS with all of my information secured in case the laptop is ever stolen or sold. Although this setup will not provide a lot of space, I think I can squeeze both OSes and have enough for second-computer office tasks. So, my questions are: Which OS should I install first, Ubuntu or Vista? Any special considerations when partitioning the drive? How should I install Ubuntu to ensure full disk encryption for the Linux partition(s) and or my daily computing? Is there a significant performance upgrade with doing a solo install of Ubuntu instead of a dual boot setup? Will TRIM, for example, work correctly? Are there any significant security concerns with going the route of a dual-boot, other than the fact that any activity on Windows may be fully recoverable if the drive is stolen or sold? Thanks in advance!

    Read the article

  • Why is Ubuntu One slow to sync in 11.10, either backup or any sub-folder contents?

    - by pst007x
    I have been trying to sync my documents folder of 1.4GB, it still hasn't worked and it has been syncing for a month. The top level syncs, files and folders in the Document folders, but contents of sub-folders just hang. (Gave up and stopped syncing this folder) However,I have tried using the backup facility in 11.10, to backup to Ubuntu One.... I upgraded my HDD space in Ubuntu One. It has been going now for 24hours-ish and only backed up what looks like a couple of percent. (By the way what an excellent idea to backup to Ubuntu One, if only we could get it to actually work! :-o) The odd thing is I can sync to drop box within hours, rather than months. This is bad, and has been an issue since Ubuntu One's release. I have reported this problem and there were promises in later releases this would be fixed, but it hasn't. Canonical cannot help either... I posted on several blogs, a lot of people have the same problem but no fixes. So do I use dropbox or another service, until it is sorted, as Ubuntu does not seem to see this as an issue, I think a fix will be a long time in coming. (However,I love the potential of Ubuntu One and the integration with the OS) Yes my internet speeds are fine, etc... :-) No firewall (sudo ufw status: STATUS: INACTIVE), No Proxy, etc NB: I have raised this as a separate question to others posted here, because my question relates to Ubuntu 11.10, though I have commented elsewhere for help. Plus my question also relates to deja-dup backup to Ubuntu One. Thanks

    Read the article

  • Ubuntu One, compressed files

    - by user8179
    I have uploaded some files to my Ubuntu One account and it seems to work great most of the time. I usually upload them directly from Nautilus by right clicking the folder, using the ”Synchronize this folder” option, and then I make sure that the file I want to upload is published. Then I usually test the whole thing by trying to download it. I right click the file again to get its URL and I paste it into my Web browser. This usually works fine. But yesterday I uploaded two compressed files – ”.tar.bz2”. When I tried to open them after downloading them with my Web browser (Opera), it failed. I found that the file was bigger than the original file (2358 B instead af 2335 B – 15 B added at the beginning of the file and 8 B added to the end), and someone at the Opera channel (IRC) at OperaNet (Europe) figured out that the reason for this is that the server compress the file again, ”without telling Opera”. So to be able to extract the file I need to add ”.gz” to the file name and then extract it twice. If I downloaded it with Firefox however, I didn't need to do that, so maybe Firefox figured this out somehow in a way that Opera does not. Someone also tried to download the file with wget and some other browser and he also got the same result as I did with Opera, that is the file is compressed a second time by the server. I guess ”the server” is the Ubuntu One server, right? So why is this? Could it be done better somehow? Or did I do something wrong when uploading the files? It also seems like this extra compressing thing does not always happen, because when I tried again a few minutes ago, the file came down with its right size (2335 B), without an extra compression. But the other file (114 MiB) was still compressed twice.

    Read the article

  • Instalar o Ubuntu / Install Ubuntu

    - by Joaquim Venâncio
    10:10 I installed Ubuntu alongside Windows 7, after the installation was able to upgrade to version 4.11. Now I'm trying to update to version 11.10 but I get an error message saying it is not possible to upgrade, I decided to install a partition that I created the part, but when I start the PC directly opens Windows 7 does not appear to me the option to choose which want to start the operating system. I formatted the partition where you had installed ubuntu, I've been looking for tutorials where you learn how to install ubuntu on a partition part to try to understand what my problem. I wonder if I can explain how to install ubuntu on a partition that part so that when I connect the PC to show me the option to choose which system I want to start.

    Read the article

  • Upgrade Ubuntu 10.04 to Ubuntu 10.10

    - by user8561
    Hi. I'm new to these forums so I'll be quick. When I try to upgrade to Ubuntu 10.10 from 10.04 I get this error, I have tried upgrading from Terminal and Update Manager as well. Could not determine the upgrade An unresolvable problem occurred while calculating the upgrade: E:Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. This can be caused by: * Upgrading to a pre-release version of Ubuntu * Running the current pre-release version of Ubuntu * Unofficial software packages not provided by Ubuntu If none of this applies, then please report this bug against the 'update-manager' package and include the files in /var/log/dist-upgrade/ in the bug report. Restoring original system state Thanks Aborting

    Read the article

  • Sporadic unspecific kernel panic

    - by koma
    I'm experiencing seldom (so far about once a month) hard crashes on our ubuntu server 10.04 LTS box. The box itself is quite old (Dell PowerEdge 750 from 2004, Pentium4 2.8 GHz). I set up netconsole after it crashed twice last thursday and was able to extract the following output: [ 9354.062473] invalid opcode: 0000 [#1] SMP [ 9354.062516] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/uevent [ 9354.062555] Modules linked in: ppdev adm1026 hwmon_vid i2c_i801 bridge stp dcdbas psmouse serio_raw netconsole configfs shpchp lp parport usbhid hid e1000 [ 9354.062685] [ 9354.062704] Pid: 3988, comm: rsync Not tainted 2.6.38-12-generic-pae #51~lucid1-Ubuntu Dell Computer Corporation PowerEdge 750 /0R1479 [ 9354.062773] EIP: 0060:[<c104fef1>] EFLAGS: 00010046 CPU: 1 [ 9354.062802] EIP is at check_preempt_wakeup+0x181/0x250 [ 9354.062826] EAX: 00000002 EBX: f2a10ccc ECX: 00000000 EDX: 00000002 [ 9354.062850] ESI: f1db71cc EDI: f1db71a0 EBP: f1dbdea8 ESP: f1dbde8c [ 9354.062875] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 9354.062900] Process rsync (pid: 3988, ti=f1dbc000 task=f1db71a0 task.ti=f1dbc000) [ 9354.062933] Stack: [ 9354.062951] 0053ea60 f7907680 f28da840 f2a10ca0 c153ea60 f7907680 c153ea60 f1dbdebc [ 9354.063019] c103f98a f2a10ca0 f7907680 00000001 f1dbdef8 c104f97f 00000000 f2f0bacc [ 9354.063088] f7904338 00000001 00000003 00000000 f2f0bacc 00000001 00000001 00000086 [ 9354.063157] Call Trace: [ 9354.063183] [<c103f98a>] check_preempt_curr+0x6a/0x80 [ 9354.063210] [<c104f97f>] try_to_wake_up+0x5f/0x3f0 [ 9354.063236] [<c1077a00>] ? hrtimer_wakeup+0x0/0x30 [ 9354.063261] [<c104fd64>] wake_up_process+0x14/0x20 [ 9354.063286] [<c1077a1d>] hrtimer_wakeup+0x1d/0x30 [ 9354.063310] [<c1077f4a>] __run_hrtimer+0x7a/0x1c0 [ 9354.063336] [<c107dbad>] ? ktime_get+0x6d/0x110 [ 9354.063360] [<c1078310>] hrtimer_interrupt+0x120/0x2b0 [ 9354.063390] [<c1535c36>] smp_apic_timer_interrupt+0x56/0x8a [ 9354.063418] [<c152f459>] apic_timer_interrupt+0x31/0x38 [ 9354.063446] [<c1520000>] ? mca_attach_bus+0x5/0xc0 [ 9354.063469] Code: 8b 9b 20 01 00 00 8b 86 24 01 00 00 3b 83 24 01 00 00 75 e6 85 db 0f 84 a3 00 00 00 89 da 89 f0 e8 75 f6 fe ff 83 f8 01 0f 85 00 <fe> ff ff 89 f8 e8 95 f9 fe ff 8b 5e 1c 85 db 0f 84 e4 fe ff ff [ 9354.063804] EIP: [<c104fef1>] check_preempt_wakeup+0x181/0x250 SS:ESP 0068:f1dbde8c [ 9354.064231] ---[ end trace 290689cea65aea7f ]--- [ 9354.064290] Kernel panic - not syncing: Fatal exception in interrupt [ 9354.064352] Pid: 3988, comm: rsync Tainted: G D 2.6.38-12-generic-pae #51~lucid1-Ubuntu [ 9354.064424] Call Trace: [ 9354.064481] [<c152c057>] ? panic+0x5c/0x15b [ 9354.064539] [<c15302bd>] ? oops_end+0xcd/0xd0 [ 9354.064539] [<c100d9e4>] ? die+0x54/0x80 [ 9354.064539] [<c152f926>] ? do_trap+0x96/0xc0 [ 9354.064539] [<c100ba00>] ? do_invalid_op+0x0/0xa0 [ 9354.064539] [<c100ba8b>] ? do_invalid_op+0x8b/0xa0 [ 9354.064539] [<c104fef1>] ? check_preempt_wakeup+0x181/0x250 [ 9354.064539] [<c144884d>] ? __kfree_skb+0x3d/0x90 [ 9354.064539] [<c1042ae7>] ? update_curr+0x247/0x2a0 [ 9354.064539] [<c10447bb>] ? update_cfs_load+0x11b/0x2d0 [ 9354.064539] [<c1042a25>] ? update_curr+0x185/0x2a0 [ 9354.064539] [<c152f6bf>] ? error_code+0x67/0x6c [ 9354.064539] [<c104fef1>] ? check_preempt_wakeup+0x181/0x250 [ 9354.064539] [<c103f98a>] ? check_preempt_curr+0x6a/0x80 [ 9354.064539] [<c104f97f>] ? try_to_wake_up+0x5f/0x3f0 [ 9354.064539] [<c1077a00>] ? hrtimer_wakeup+0x0/0x30 [ 9354.064539] [<c104fd64>] ? wake_up_process+0x14/0x20 [ 9354.064539] [<c1077a1d>] ? hrtimer_wakeup+0x1d/0x30 [ 9354.064539] [<c1077f4a>] ? __run_hrtimer+0x7a/0x1c0 [ 9354.064539] [<c107dbad>] ? ktime_get+0x6d/0x110 [ 9354.064539] [<c1078310>] ? hrtimer_interrupt+0x120/0x2b0 [ 9354.064539] [<c1535c36>] ? smp_apic_timer_interrupt+0x56/0x8a [ 9354.064539] [<c152f459>] ? apic_timer_interrupt+0x31/0x38 [ 9354.064539] [<c1520000>] ? mca_attach_bus+0x5/0xc0 Googling for this issue didn't really turn up anything useful (most stuff I found was related to btrfs, but I don't use that, although the module exists and is sometimes loaded). From experience it might have to do with relatively heavy I/O, as two of the panics happened during a backup procedure. Kernel is 2.6.38-12-generic-pae, but I'm pretty sure I also saw panics on 2.6.32. I meanwhile upgraded to 3.0.0-17-generic-pae and am waiting for the next crash ;-) I'm at a loss here, so any pointers where to look for the cause or what it could be would be great :-) Thanks !

    Read the article

  • strange bundler error: tar_input.rb:49:in `initialize': not in gzip format (Zlib::GzipFile::Error) o

    - by z3cko
    i am getting a strange bundler error when running bundle pack with bundler 0.9.12 any ideas? (see pastie for a better formatted code: http://pastie.org/881328 ) /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_input.rb:49:in `initialize': not in gzip format (Zlib::GzipFile::Error) from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_input.rb:49:in `new' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_input.rb:49:in `initialize' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_reader.rb:63:in `each' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_reader.rb:54:in `loop' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_reader.rb:54:in `each' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_input.rb:32:in `initialize' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_input.rb:17:in `new' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package/tar_input.rb:17:in `open' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/package.rb:55:in `open' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/format.rb:63:in `from_io' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/format.rb:51:in `from_file_by_path' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/format.rb:50:in `open' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/site_ruby/1.8/rubygems/format.rb:50:in `from_file_by_path' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/source.rb:115:in `specs' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/source.rb:114:in `each' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/source.rb:114:in `specs' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/index.rb:32:in `from_cached_specs' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/index.rb:23:in `application_cached_gems' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/index.rb:15:in `cached_gems' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/index.rb:5:in `build' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/index.rb:14:in `cached_gems' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/environment.rb:15:in `index' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/index.rb:5:in `build' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/environment.rb:13:in `index' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/runtime.rb:86:in `specs' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/runtime.rb:130:in `details' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/runtime.rb:119:in `write_yml_lock' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/runtime.rb:65:in `lock' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/cli.rb:89:in `lock' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/cli.rb:131:in `package' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor/task.rb:33:in `send' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor/task.rb:33:in `run' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor/invocation.rb:109 from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor/invocation.rb:116:in `call' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor/invocation.rb:116:in `invoke' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor.rb:137:in `start' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor/base.rb:378:in `start' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/lib/bundler/vendor/thor.rb:124:in `start' from /opt/ruby-enterprise-1.8.7-2010.01/lib/ruby/gems/1.8/gems/bundler-0.9.12/bin/bundle:11 from /opt/REE/bin/bundle:19:in `load' from /opt/REE/bin/bundle:19

    Read the article

  • Cherokee web server on Ubuntu Lucid

    - by Fazal
    I've been trying to find some decent tutorials on how to set up a recent release of Cherokee webserver on Ubuntu (or equivalent Linux distros) which outline how to setup the webserver, mysql, phpmyadmin and php. Some already exist, such as http://www.howtoforge.com/installing-cherokee-with-php5-and-mysql-support-on-ubuntu-10.04 however, I've found that the Cherokee version used in the tutorial is considerably out of date and the update process has been painful to say the least. Thanks.

    Read the article

  • Wireless not working - HP Probook 4540s

    - by Oguzhan
    I just installed Ubuntu 12.04 on 3 HP Probook 4540s's, and none of them seems to be able to connect to wireless networks. I have 1 Probook 4540s with Windows 7 installed and I can access wlan from it. I tried installing the necessary drivers from HP's website, but it still doesn't seem to be working. I've seen other people with different Probooks having similar problems, but their computers seem to be able to detect and even attempt to connect wlans, while mine doesn't even acknowledge that it has wireless. Any help would be appreciated. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Thames [Radeon 7500M/7600M Series] 03:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 30) 03:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 30) 03:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 30) 04:00.0 Network controller: Ralink corp. Device 3290 04:00.1 Bluetooth: Ralink corp. Device 3298 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07)

    Read the article

  • How do I free up more space in /boot?

    - by user6722
    My /boot partition is nearly full and I get a warning every time I reboot my system. I already deleted old kernel packages (linux-headers...), actually I did that to install a newer kernel version that came with the automatic updates. After installing that new version, the partition is nearly full again. So what else can I delete? Are there some other files associated to the old kernel images? Here is a list of files that are on my /boot partition: :~$ ls /boot/ abi-2.6.31-21-generic lost+found abi-2.6.32-25-generic memtest86+.bin abi-2.6.38-10-generic memtest86+_multiboot.bin abi-2.6.38-11-generic System.map-2.6.31-21-generic abi-2.6.38-12-generic System.map-2.6.32-25-generic abi-2.6.38-8-generic System.map-2.6.38-10-generic abi-3.0.0-12-generic System.map-2.6.38-11-generic abi-3.0.0-13-generic System.map-2.6.38-12-generic abi-3.0.0-14-generic System.map-2.6.38-8-generic boot System.map-3.0.0-12-generic config-2.6.31-21-generic System.map-3.0.0-13-generic config-2.6.32-25-generic System.map-3.0.0-14-generic config-2.6.38-10-generic vmcoreinfo-2.6.31-21-generic config-2.6.38-11-generic vmcoreinfo-2.6.32-25-generic config-2.6.38-12-generic vmcoreinfo-2.6.38-10-generic config-2.6.38-8-generic vmcoreinfo-2.6.38-11-generic config-3.0.0-12-generic vmcoreinfo-2.6.38-12-generic config-3.0.0-13-generic vmcoreinfo-2.6.38-8-generic config-3.0.0-14-generic vmcoreinfo-3.0.0-12-generic extlinux vmcoreinfo-3.0.0-13-generic grub vmcoreinfo-3.0.0-14-generic initrd.img-2.6.31-21-generic vmlinuz-2.6.31-21-generic initrd.img-2.6.32-25-generic vmlinuz-2.6.32-25-generic initrd.img-2.6.38-10-generic vmlinuz-2.6.38-10-generic initrd.img-2.6.38-11-generic vmlinuz-2.6.38-11-generic initrd.img-2.6.38-12-generic vmlinuz-2.6.38-12-generic initrd.img-2.6.38-8-generic vmlinuz-2.6.38-8-generic initrd.img-3.0.0-12-generic vmlinuz-3.0.0-12-generic initrd.img-3.0.0-13-generic vmlinuz-3.0.0-13-generic initrd.img-3.0.0-14-generic vmlinuz-3.0.0-14-generic Currently, I'm using the 3.0.0-14-generic kernel.

    Read the article

  • VGA monitor won't detect on NVIDIA Quadro NVS 4200M

    - by tanmayk
    I am on a Dell Latitude E6420 and just installed 12.04. When I plug in my external monitor's VGA cable, the laptop doesn't detect any new monitor. Here's the output of my lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [Quadro NVS 4200M] (rev a1) 01:00.1 Audio device: NVIDIA Corporation HDMI Audio stub (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 (rev 34) 0b:00.0 SD Host controller: O2 Micro, Inc. Device 8221 (rev 05) 0b:00.1 Mass storage controller: O2 Micro, Inc. Device 8231 (rev 03) I tried installing the Quadro NVS 4200M from the nvidia website but got stuck in TTY after the installation finished. Any ideas as to how I can get the external monitor to work? Thanks!

    Read the article

  • IntelliJ 12 - Grails Distribution in specified path is broken

    - by Prayag Upd
    I am struggling to configure grails 2.3.X in IntelliJ idea 12. Grails 2.2.X is configured successfully. Grails 2.3.2 is working properly from terminal. I can compile, test, run my application. But while trying to configure it in IntelliJ so that dependencies get resolved, I get the IntelliJ shouting straight to me(as pictured below). Looks like Grails Distribution in specified path is broken. Cannot determinate version. What I see is changes in grails-2.3.x/dist/ to earlier version's grails-2.2.x/dist/. Is this because there's no support for newer version(2.3.x) of grails in IntelliJ 12 or what ? I want nothing else but my application (jar) dependencies to be resolved in the IDE.

    Read the article

  • Is InstallShield 2010 really necessary to support Windows 7 (against using InstallShield 12)

    - by Steve
    I have received an e-mail from Flexera containing the following statement: "We understand that many of our customers still using InstallShield 12 maybe having difficulties sending installations to Windows 7 desktops, 64 Bit servers or R2 2008. Therefore we would like to provide this opportunity for you to erase these potential / current problems and upgrade despite InstallShield 12 being End of Life’d some time ago." We have not had any problems ourselves. I am interested to hear if anyone else has had any issues or whether this is a scare to get us to upgrade unnecessarily. I did examine in some detail the differences at the original end-of-life notice but could not see any issues that affected our installations. Interestingly they call this an 'amnesty' - almost implying we are criminals for not upgrading (cf OED).

    Read the article

  • Why No android.content.SyncAdapter meta-data registering sync-adapter?

    - by mobibob
    I am following the SampleSyncAdapter and upon startup, it appears that my SyncAdapter is not configured correctly. It reports an error trying to load its meta-data. How can I isolate the problem? You can see the other accounts in the system that register correctly. Logcat: 12-21 17:10:50.667 W/PackageManager( 121): Unable to load service info ResolveInfo{4605dcd0 com.myapp.syncadapter.MySyncAdapter p=0 o=0 m=0x108000} 12-21 17:10:50.667 W/PackageManager( 121): org.xmlpull.v1.XmlPullParserException: No android.content.SyncAdapter meta-data 12-21 17:10:50.667 W/PackageManager( 121): at android.content.pm.RegisteredServicesCache.parseServiceInfo(RegisteredServicesCache.java:391) 12-21 17:10:50.667 W/PackageManager( 121): at android.content.pm.RegisteredServicesCache.generateServicesMap(RegisteredServicesCache.java:260) 12-21 17:10:50.667 W/PackageManager( 121): at android.content.pm.RegisteredServicesCache$1.onReceive(RegisteredServicesCache.java:110) 12-21 17:10:50.667 W/PackageManager( 121): at android.app.ActivityThread$PackageInfo$ReceiverDispatcher$Args.run(ActivityThread.java:892) 12-21 17:10:50.667 W/PackageManager( 121): at android.os.Handler.handleCallback(Handler.java:587) 12-21 17:10:50.667 W/PackageManager( 121): at android.os.Handler.dispatchMessage(Handler.java:92) 12-21 17:10:50.667 W/PackageManager( 121): at android.os.Looper.loop(Looper.java:123) 12-21 17:10:50.667 W/PackageManager( 121): at com.android.server.ServerThread.run(SystemServer.java:570) 12-21 17:10:50.747 D/Sources ( 294): Creating external source for type=com.skype.contacts.sync, packageName=com.skype.raider 12-21 17:10:50.747 D/Sources ( 294): Creating external source for type=com.twitter.android.auth.login, packageName=com.twitter.android 12-21 17:10:50.747 D/Sources ( 294): Creating external source for type=com.example.android.samplesync, packageName=com.example.android.samplesync 12-21 17:10:50.747 W/PackageManager( 121): Unable to load service info ResolveInfo{460504b0 com.myapp.syncadapter.MySyncAdapter p=0 o=0 m=0x108000} 12-21 17:10:50.747 W/PackageManager( 121): org.xmlpull.v1.XmlPullParserException: No android.content.SyncAdapter meta-data 12-21 17:10:50.747 W/PackageManager( 121): at android.content.pm.RegisteredServicesCache.parseServiceInfo(RegisteredServicesCache.java:391) 12-21 17:10:50.747 W/PackageManager( 121): at android.content.pm.RegisteredServicesCache.generateServicesMap(RegisteredServicesCache.java:260) 12-21 17:10:50.747 W/PackageManager( 121): at android.content.pm.RegisteredServicesCache$1.onReceive(RegisteredServicesCache.java:110) 12-21 17:10:50.747 W/PackageManager( 121): at android.app.ActivityThread$PackageInfo$ReceiverDispatcher$Args.run(ActivityThread.java:892) 12-21 17:10:50.747 W/PackageManager( 121): at android.os.Handler.handleCallback(Handler.java:587) 12-21 17:10:50.747 W/PackageManager( 121): at android.os.Handler.dispatchMessage(Handler.java:92) 12-21 17:10:50.747 W/PackageManager( 121): at android.os.Looper.loop(Looper.java:123) 12-21 17:10:50.747 W/PackageManager( 121): at com.android.server.ServerThread.run(SystemServer.java:570)

    Read the article

  • Microsoft.ACE.OLEDB.12.0 has not been Registered" Error

    - by brohjoe
    I'm getting a "The OLE DB provider "Microsoft.ACE.OLEDB.12.0 has not been registered" error. I have the data objects library downloaded and I have "Microsoft Office 12.0 Access database engine Object Library" selected. I'm running the Windows Vista 32-bit operating system. Any ideas would be greatly appreciated.

    Read the article

  • What's the significance of Oct 12 1999?

    - by Portman
    In the SignOut method of System.Web.Security.FormsAuthentication, the ASP.NET team chose to expire the FormsAuth cookie by setting the expiration date to "Oct 12 1999". HttpCookie cookie = new HttpCookie(FormsCookieName, str); cookie.HttpOnly = true; cookie.Path = _FormsCookiePath; cookie.Expires = new DateTime(0x7cf, 10, 12); What's the significance of October 12th, 1999? Is it an inside joke, or is there some valid reason to set your cookie expiration to that particular date? Edit: The theories below are interesting, but they are just guesses. Since Phil, Scott, and other members of the ASP.NET team are on StackOverflow, I thought it would be fun to offer a bounty. Hopefully someone can track down the original developer and get an authoritative answer. Awarded: To Scott Hanselman for escalating this one all the way to ScottGu. I was really hoping for some sort of super-secret, Illuminati-esque meaning, but looks like it was just the old "one year ago" trick.

    Read the article

  • Ubuntu to Ubuntu VNC over SSH tunnel

    - by rxt
    I have a Linux Ubuntu desktop at home, ssh enabled, vnc server installed, router rule configured. It all works, and at home I can connect via the local network from my Mac. From the outside I can login via ssh. I've configured putty as follows: session: host name and port number connection ssh tunnel: forwarded ports: L5900|192.168.0.23 the local address is: 192.168.1.45 When I make the connection I can login to the remote machine. Then I open Remote Desktop Viewer. I click connect protocol: vnc host: ? use host as ssh tunnel: ? I don't know what to use for the last two options. Which ip-addresses should I use?

    Read the article

  • Getting Cabal to work with GHC 6.12.1

    - by Dan Dyer
    I've installed the latest GHC package (6.12.1) on OS X, but I can't get Cabal to work. I've removed the version I had previously that worked with GHC 6.10 and tried to re-install from scratch. The latest Cabal version available for download is 1.6.0.2. However, when I try to build this I get the following error: Configuring Cabal-1.6.0.2... Setup: failed to parse output of 'ghc-pkg dump' From what I've found searching, this seems to suggest that the version of Cabal is too old for the version of GHC. Is there any way to get Cabal to work with GHC 6.12.1 yet? EDIT: To be clear, I'm trying to set-up cabal-install.

    Read the article

  • ubuntu to ubuntu backup in internal network

    - by amirash
    hey, i got my development "home" server witch is ubuntu 10, i brought today a computer in order to make a backup to this computer (the development server does also to him self backups every day but im paranoaid so i want to have two backups just in case on diffrent computers) what is the best way to backup the system core of the development server (like norton ghost) & do a full & incrmnt backup of him to the new computer that ive brought? rsync? rdiff? scp? clonezilla?

    Read the article

  • ubuntu to ubuntu backup in internal network

    - by amirash
    hey, i got my development "home" server witch is ubuntu 10, i brought today a computer in order to make a backup to this computer (the development server does also to him self backups every day but im paranoaid so i want to have two backups just in case on diffrent computers) what is the best way to backup the system core of the development server (like norton ghost) & do a full & incrmnt backup of him to the new computer that ive brought? rsync? rdiff? scp? clonezilla?

    Read the article

  • It's like I'm in recovery mode after update, but I'm not

    - by mawburn
    I used the Ubuntu software updater and updated to the most recent packages. After the last update today, it's like I have gone into recovery mode, but I haven't. I am running UbuntuGNOME First, everything looks like this: Switching to dark mode does nothing. Also, default applications do not work. Such as Startup and the default screenshot application. Everything was working fine before the latest software update. System Info Ubuntu 14.04 LTS Gnome-Shell 3.10.4 Kernel 3.13.0-29 I can't figure out how to get an update history, but this is almost a fresh install. It's about a week old install and this is the 3rd time I've used the Ubuntu Software Update. I am running AMD ATI HD6700 with the proprietary Catalyst drivers. I tried to provide all information that I thought would be useful, if you need any more please let me know. Edit - I believe something went wrong within these updates: Update Log: Start-Date: 2014-06-09 19:07:07 Commandline: aptdaemon role='role-commit-packages' sender=':1.68' Install: libgnome-desktop-3-10:amd64 (3.12.0-0~eugenesan~trusty2) Upgrade: gnome-session-common:amd64 (3.9.90-0ubuntu12, 3.12.0-0~eugenesan~trusty10), gnome-session-bin:amd64 (3.9.90-0ubuntu12, 3.12.0-0~eugenesan~trusty10), gir1.2-gnomedesktop-3.0:amd64 (3.8.4-0ubuntu3, 3.12.0-0~eugenesan~trusty2), gnome-session:amd64 (3.9.90-0ubuntu12, 3.12.0-0~eugenesan~trusty10), python-libxml2:amd64 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), libspice-server1:amd64 (0.12.4-0nocelt2, 0.12.4-0nocelt2.02~eugenesan~trusty1), gir1.2-mutter-3.0:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1), xserver-xorg-video-qxl:amd64 (0.1.1-0ubuntu3, 0.1.1-0ubuntu3.01), libxml2:amd64 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), libxml2:i386 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), gnome-desktop3-data:amd64 (3.8.4-0ubuntu3, 3.12.0-0~eugenesan~trusty2), mutter:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1), mutter-common:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1), libxml2-utils:amd64 (2.9.1+dfsg1-3ubuntu4.1, 2.9.1+dfsg1-3ubuntu4.2), libmutter0c:amd64 (3.10.4-0ubuntu2, 3.10.4-0ubuntu2.1) End-Date: 2014-06-09 19:07:12 I also installed Citrix Receiver today, following the tutorial here: Citrix Receiver 12.1 on Ubuntu 14.04 64-bit Log Start-Date: 2014-06-09 18:59:06 Commandline: apt-get install libmotif4:i386 nspluginwrapper lib32z1 libc6-i386 libxp6:i386 libxpm4:i386 libasound2:i386 Install: libmotif-common:amd64 (2.3.4-5, automatic), libatk1.0-0:i386 (2.10.0-2ubuntu2, automatic), libxft2:i386 (2.3.1-2, automatic), libgraphite2-3:i386 (1.2.4-1ubuntu1, automatic), nspluginviewer:i386 (1.4.4-0ubuntu5, automatic), libpango-1.0-0:i386 (1.36.3-1ubuntu1, automatic), libxcursor1:i386 (1.1.14-1, automatic), libmotif4:i386 (2.3.4-5), libxm4:amd64 (2.3.4-5, automatic), libxm4:i386 (2.3.4-5, automatic), libxp6:i386 (1.0.2-1ubuntu1), libpangocairo-1.0-0:i386 (1.36.3-1ubuntu1, automatic), libxcb-render0:i386 (1.10-2ubuntu1, automatic), libthai0:i386 (0.1.20-3, automatic), libharfbuzz0b:i386 (0.9.27-1, automatic), libpixman-1-0:i386 (0.30.2-2ubuntu1, automatic), libpangoft2-1.0-0:i386 (1.36.3-1ubuntu1, automatic), libcairo2:i386 (1.13.0~20140204-0ubuntu1, automatic), lib32z1:amd64 (1.2.8.dfsg-1ubuntu1), libjasper1:i386 (1.900.1-14ubuntu3, automatic), libgtk2.0-0:i386 (2.24.23-0ubuntu1.1, automatic), nspluginwrapper:amd64 (1.4.4-0ubuntu5), libuil4:amd64 (2.3.4-5, automatic), libuil4:i386 (2.3.4-5, automatic), libxcb-shm0:i386 (1.10-2ubuntu1, automatic), libxmu6:i386 (1.1.1-1, automatic), libc6-i386:amd64 (2.19-0ubuntu6), libxinerama1:i386 (1.1.3-1, automatic), libgdk-pixbuf2.0-0:i386 (2.30.7-0ubuntu1, automatic), libxcomposite1:i386 (0.4.4-1, automatic), libmrm4:amd64 (2.3.4-5, automatic), libmrm4:i386 (2.3.4-5, automatic), libdatrie1:i386 (0.2.8-1, automatic), libxrandr2:i386 (1.4.2-1, automatic), libxpm4:i386 (3.5.10-1) End-Date: 2014-06-09 18:59:11

    Read the article

  • Windows XP Ubuntu Installer (version 11.10) error dialog - Permission Denied

    - by MacGyver
    When installing Ubuntu 11.10 on Windows XP (2nd option in installer), the install failed with popup. How can I fix this? Here is the contents of file "C:\Documents and Settings\Keith\Local Settings\Temp\wubi-11.10-rev241.log". I only pasted the last few lines because of the question size limit. \Temp\pyl1.tmp\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp is a valid Kubuntu CD 03-25 22:29 DEBUG Distro: does not contain C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp is a valid Kubuntu CD 03-25 22:29 DEBUG Distro: does not contain C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp is a valid Xubuntu CD 03-25 22:29 DEBUG Distro: does not contain C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp is a valid Xubuntu CD 03-25 22:29 DEBUG Distro: does not contain C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp is a valid Mythbuntu CD 03-25 22:29 DEBUG Distro: does not contain C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp is a valid Mythbuntu CD 03-25 22:29 DEBUG Distro: does not contain C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Ubuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Kubuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Xubuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether D:\ is a valid Mythbuntu CD 03-25 22:29 DEBUG Distro: does not contain D:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Ubuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Kubuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Xubuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether E:\ is a valid Mythbuntu CD 03-25 22:29 DEBUG Distro: does not contain E:\casper\filesystem.squashfs 03-25 22:29 DEBUG Distro: checking whether Y:\ is a valid Ubuntu CD 03-25 22:29 INFO Distro: Found a valid CD for Ubuntu: Y:\ 03-25 22:29 INFO root: Running the installer... 03-25 22:29 INFO WinuiPage: appname=wubi, localedir=C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\translations, languages=['en_US', 'en'] 03-25 22:29 INFO WinuiPage: appname=wubi, localedir=C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\translations, languages=['en_US', 'en'] 03-25 22:29 DEBUG WinuiInstallationPage: target_drive=C:, installation_size=18000MB, distro_name=Ubuntu, language=en_US, locale=en_US.UTF-8, username=keith 03-25 22:29 INFO root: Received settings 03-25 22:29 INFO WinuiPage: appname=wubi, localedir=C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\translations, languages=['en_US', 'en'] 03-25 22:29 DEBUG TaskList: # Running tasklist... 03-25 22:29 DEBUG TaskList: ## Running select_target_dir... 03-25 22:29 INFO WindowsBackend: Installing into C:\ubuntu 03-25 22:29 DEBUG TaskList: ## Finished select_target_dir 03-25 22:29 DEBUG TaskList: ## Running create_dir_structure... 03-25 22:29 DEBUG CommonBackend: Creating dir C:\ubuntu 03-25 22:29 DEBUG CommonBackend: Creating dir C:\ubuntu\disks 03-25 22:29 DEBUG CommonBackend: Creating dir C:\ubuntu\install 03-25 22:29 DEBUG CommonBackend: Creating dir C:\ubuntu\install\boot 03-25 22:29 DEBUG CommonBackend: Creating dir C:\ubuntu\disks\boot 03-25 22:29 DEBUG CommonBackend: Creating dir C:\ubuntu\disks\boot\grub 03-25 22:29 DEBUG CommonBackend: Creating dir C:\ubuntu\install\boot\grub 03-25 22:29 DEBUG TaskList: ## Finished create_dir_structure 03-25 22:29 DEBUG TaskList: ## Running uncompress_target_dir... 03-25 22:29 DEBUG TaskList: ## Finished uncompress_target_dir 03-25 22:29 DEBUG TaskList: ## Running create_uninstaller... 03-25 22:29 DEBUG WindowsBackend: Copying uninstaller Y:\wubi.exe -> C:\ubuntu\uninstall-wubi.exe 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi UninstallString C:\ubuntu\uninstall-wubi.exe 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi InstallationDir C:\ubuntu 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayName Ubuntu 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayIcon C:\ubuntu\Ubuntu.ico 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi DisplayVersion 11.10-rev241 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi Publisher Ubuntu 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi URLInfoAbout http://www.ubuntu.com 03-25 22:29 DEBUG registry: Setting registry key -2147483646 Software\Microsoft\Windows\CurrentVersion\Uninstall\Wubi HelpLink http://www.ubuntu.com/support 03-25 22:29 DEBUG TaskList: ## Finished create_uninstaller 03-25 22:29 DEBUG TaskList: ## Running copy_installation_files... 03-25 22:29 DEBUG WindowsBackend: Copying C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\data\custom-installation -> C:\ubuntu\install\custom-installation 03-25 22:29 DEBUG WindowsBackend: Copying C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\winboot -> C:\ubuntu\winboot 03-25 22:29 DEBUG WindowsBackend: Copying C:\DOCUME~1\Keith\LOCALS~1\Temp\pyl1.tmp\data\images\Ubuntu.ico -> C:\ubuntu\Ubuntu.ico 03-25 22:29 DEBUG TaskList: ## Finished copy_installation_files 03-25 22:29 DEBUG TaskList: ## Running get_iso... 03-25 22:29 DEBUG TaskList: New task copy_file 03-25 22:29 DEBUG TaskList: ### Running copy_file... 03-25 22:32 ERROR TaskList: [Errno 13] Permission denied Traceback (most recent call last): File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\common\utils.py", line 202, in copy_file IOError: [Errno 13] Permission denied 03-25 22:32 DEBUG TaskList: # Cancelling tasklist 03-25 22:32 DEBUG TaskList: New task check_iso 03-25 22:32 ERROR root: [Errno 13] Permission denied Traceback (most recent call last): File "\lib\wubi\application.py", line 58, in run File "\lib\wubi\application.py", line 130, in select_task File "\lib\wubi\application.py", line 205, in run_cd_menu File "\lib\wubi\application.py", line 120, in select_task File "\lib\wubi\application.py", line 158, in run_installer File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\common\utils.py", line 202, in copy_file IOError: [Errno 13] Permission denied 03-25 22:32 ERROR TaskList: 'WindowsBackend' object has no attribute 'iso_path' Traceback (most recent call last): File "\lib\wubi\backends\common\tasklist.py", line 197, in __call__ File "\lib\wubi\backends\common\backend.py", line 579, in get_iso File "\lib\wubi\backends\common\backend.py", line 565, in use_iso AttributeError: 'WindowsBackend' object has no attribute 'iso_path' 03-25 22:32 DEBUG TaskList: # Cancelling tasklist 03-25 22:32 DEBUG TaskList: # Finished tasklist

    Read the article

  • ubuntu one no inicia sesion desde windows 7

    - by Eder BOhorquez
    hola personal de ubuntu mi nombre es eder bohorquez y soy de colombia tengo problemas con el inicio de sesion desde windows 7 ya he probado en dos diferentes computadores y no me ha dejado iniciar sesion acudo a ustedes para que me ayuden a resolver este inconveniente. especificaciones pc ambos computadores tienen el mismo sistema operativo instalado, como se puede apreciar en la imagen son las especificaciones de mi pc. de antemano muchas gracias por su colaboracion.

    Read the article

  • Install Ubuntu or Kubuntu on a External USB Drive

    - by rihatum
    Hi All, I have a few external hard drives (SSDs and Platters (SATA), is this possible that I can install Kubuntu 10.10 x64 or Ubuntu 10.10 x64 onto one of these external hard drives? My System supports booting off a usb, it will just give me a learning playground without spoiling my existing operating environment. I know I can install as Virtual machines, but installing U/Kubuntu on a External HDD and booting off it would be easier. Will be grateful for your insights....and steps to do so. Thanks

    Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >