Search Results

Search found 20140 results on 806 pages for 'remote management'.

Page 700/806 | < Previous Page | 696 697 698 699 700 701 702 703 704 705 706 707  | Next Page >

• Unable to connect via NetBIOS Name

  - by grom

  I can't connect to machines/shares by NetBIOS names. Below is console output showing the problem. C:\>nbtstat -n Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Local Name Table Name Type Status --------------------------------------------- BEAST <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BEAST <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered WORKGROUP <1D> UNIQUE Registered ..__MSBROWSE__.<01> GROUP Registered C:\>nbtstat -A 192.168.1.3 Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- BRCLAPTOP <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BRCLAPTOP <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered MAC Address = 00-1C-BF-14-B8-6E C:\>ping beast Pinging beast [fe80::59b8:179f:b90b:a63f%11] with 32 bytes of data: Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Ping statistics for fe80::59b8:179f:b90b:a63f%11: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping brclaptop Ping request could not find host brclaptop. Please check the name and try again. C:\>nbtstat -a brclaptop Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] Host not found.

  Read the article

• Dropped WD External Harddisk, now it's shown as "Not initialized"

  - by Phelios

  So, the WD my passport external harddisk is dropped, and after that, the computer is unable to read it anymore. I was hopping if I can just find another case to try if the harddisk is still readable, but looks like the hard drive itself is not a normal SATA or PATA drive. I think it's modified. So, I can't find another case that I can try on. In the computer, I still can see the drive in the "Disk Management", but it's shown as Uninitialized, no size, and no drive letter. I've also tried a couple of recovery tools. Some can't detect at all, there is one (find and mount software) that can detect but shows 0 size. None of them can recover the data. WD is willing to replace it with a new one, but I still need to recover the data. Any way I can recover the data? UPDATE: I tried initialized it from the windows Disk Manager, but it give error "The request could not be performed because of an I/O device error."

  Read the article

• Creating a Jenkins build farm in a hands-off manner?

  - by user183394

  My colleague and I have set up and run Jenkins on a KVM guest running Ubuntu 12.04 with good results for a while now. We are thinking about deploying a cluster of Jenkins CI hosts in master/slave configuration, with the libvirt slave plugin to keep our hardware count low. Our environment is strictly Linux (CentOS, Scientific Linux, Fedora, and Ubuntu). Both of us are competent in setting up large clusters. We typically use tools like cobbler + a configuration management tool (Puppet, Chef, and alike) to set up a large number of machines (physical and/or virtual) hands off (hundreds of nodes in less than an hour typical). We would like to do the same for nodes running Jenkins. But the step by step guide doesn't give us any clues in this regard. I did see a Multi-slave config plugin. But, being used to dealing with hundreds or more machines completely hands-off, clicking the UI for many machines just doesn't feel right. Can someone point to us a reference that talks about how to set up large cluster of Jenkins CI hosts more in the hands-off way?

  Read the article

• Mac dev folder missing, SSH not working

  - by SamGoody

  A few days ago, SSH stopped working. When I try logging in a get the following message: PTY allocation request failed on channel 0 stdin: is not a tty fatal: unrecognized command '' Connection to 74.52.61.194 closed. Web searches have shown me that there might be something wrong with /dev/std. But my computer lacks a /dev/ drive. There is an Alias to /dev/ [hidden, but I've revealed hidden files to do this search], but when I try to open it I am told that it cannot find the folder it is aliasing. Now, many a web search tells me that without a dev folder, the computer doesn't work, but it does seem to work, except the SSH. Also, are there any tools that can save my SSH preferences so that I don't have to, each time, type out the username@adrees, password, path all of which are long and complex? Not looking for a Filezilla type client, there are many of those. Looking for a command line like putty, that lets me use bash on the remote client. Am on Macbook Pro, latest version of Tiger.

  Read the article

• Power Outage Interrupted Upgrade from Windows Vista Ultimate to 7 Ultimate, Reverted to Vista, Now Vista is failing... What Next?

  - by tednewk

  I was in the midst of what seemed to be a successful upgrade from Vista Ultimate to 7 Ultimate when there was a brief blackout. The upgrade failed and Windows reverted back to Vista. Now Vista is very slow to boot, has problems waking back-up from inactivity and quickly loses it's wireless connection. The wake-up problem manifests itself as the mouse is clearly shown on a black screen but I have no access to the Desktop or Taskbar or Explorer. Even Alt-Ctrl-Delete doesn't seem to work. No task menu, no reboot. Hitting the reset button reboots the machine with the usual Black Screen warnings offering Safe Mode. I tried to do a system restore to a point before the upgrade. That didn't seem to work. My guess is that my system is a mutant with parts of Vista and parts of 7 crashing each other. I would like avoid a clean install if at all possible to avoid reinstalling other software. What should I try now? My thoughts are: My a system back-up to lock the computer in place Trying a second 7 upgrade If that appears to be working make another back-up If not reload back-up and try a repairing Vista from DVD. If that appears to work make another back-up, let system stablize about a week then try 7 install again If that doesn't work are there any other options to try before settling for a clean install? Another complication, I am doing this by "remote control". I'm traveling with my job and I'll be talking my son through it over the phone. (Kind of like the landing the 747 cliche from all the 70's adventure shows!) So is there a way of simplifying the steps? Thanks Ted

  Read the article

• Users getting 'flooded' with not read notifications (NRNs) for old emails and meeting requests

  - by Exile

  I'm being placed under quite a lot of pressure from senior management over a relatively trivial issue. Basically the vast majority of users are complaining that they receive not read notifications (NRNs) for old emails and meeting requests in large numbers multiple times a day. I know something strange is happening because some are delivered at silly times in the morning (i.e 3AM or 4AM). The problem I have is that these some of these NRNs are from meeting requests and messages that are 120 days old, so some users have deleted the original message so I don’t actually know if the NRN is from an email or meeting request. This is typical of what users receive as a NRN: From: Sender Sent: 23 March 2012 04:16 To: Recepient Subject: Not read: Accepted: Status update Your message To: Sender Subject: Accepted: Status update Sent: Wednesday, November 23, 2011 8:59:00 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Friday, March 23, 2012 4:15:32 AM (UTC) Dublin, Edinburgh, Lisbon, London. ... From: Sender Sent: 18 March 2012 01:13 To: Recepient Subject: Not read: Gold delivery - Sourcing module Your message To: Sender Subject: Gold delivery - Sourcing module Sent: Friday, November 18, 2011 9:37:58 AM (UTC) Dublin, Edinburgh, Lisbon, London was deleted without being read on Sunday, March 18, 2012 1:12:37 AM (UTC) Dublin, Edinburgh, Lisbon, London. I have done a search and found the following: http://support.microsoft.com/kb/2544246 http://support.microsoft.com/kb/2471964 But we already installed 'Update Rollup 6 for Exchange Server 2010 Service Pack 1' back in December, so I am not sure what we can do to fix this?

  Read the article

• SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database

  - by eulerfx

  I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

  Read the article

• Doesn't VirtualBox 4.0 support drag-drop file copy yet?

  - by Benjamin

  Version 4.0.0 will be new major release. The following major new features were added: -New settings/disk file layout for VM portability; see the manual for more information. -Open Virtualization Format Archive (OVA) support; see the manual for more information. -VMM: support more than 1.5/2 GB guest RAM on 32-bit hosts -Language bindings: uniform Java bindings for both local (COM/XPCOM) and remote (SOAP) -invocation APIs -Chipset: added support for the Intel ICH9 chipset with 3 PCI buses, PCI express and -Message Signaled Interrupts (MSI) -Audio: Intel HD Audio is now available as guest hardware, for better support with modern -guest operating systems (e.g. 64-bit Windows; bug #2785). -GUI: redesigned user interface with guest window preview -GUI: new display mode with downscaled guest display -Resource control: added support for limiting a VM's CPU time and IO bandwidth. -Storage: support asynchronous I/O for iSCSI, VMDK, VHD and Parallels images -Storage: support for resizing VDI and VHD images -Windows Additions: support for automatically updating the Guest Additions (requires -installed Windows Guest Additions 4.0 or later) -Guest Additions: support for copying files into the guest file system What does the last line mean? I thought this is a drag-drop file copy feature like VMWare. I tried that. But I couldn't copy by drag-drop, ctrl-c ctrl-v either. Edit: I mean VBox 4.0 beta, not 3.x The release note is here. Download link is here.

  Read the article

• Tables in the SQL Server "master" database, will they cause problems?

  - by pepoluan

  Folks, please be kind on me... I'm just an 'accidental' DBA due to our DBA resigned, so I'm totally a newbie in DBA... You see, I have this application, "ESET Remote Administration Server" (ERAS) that stores its logs and analysis on (originally) a local Access database. The decision was to migrate its database to a SQL Server 2008 R2 machine. ESET (the maker of the software) helpfully provided tools to perform such migration; unfortunately, being the DBA neophyte that I am, I didn't realize that I have to first create my own database (on the SQL Server side) and assign that database as the 'default' database for ERAS' ODBC connection. Now, the migration tool had successfully created a whole bunch of tables inside the "master" database. My questions: Should I leave things be as it is, or should I re-migrate the ERAS database to a different database? If you suggest me perform a re-migration, my plan is to (1) create a new instance, (2) create a new database within the new instance, (3) create a new ODBC System DSN on the ERAS server pointing to the new DB in step 2, (4) use ESET's migration tool to migrate from the current DSN to the new DSN. Do you think I missed a step there? Thanks beforehand for any guidance.

  Read the article

• Exchange - inbound email only works from some servers

  - by Kryptonite

  I am having a problem where inbound mail from outside only works when sent from certain hosts. For example, when I send myself an email from my personal gmail account all is well, as the logs show: 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 EHLO 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 STARTTLS 220 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 STARTTLS 220 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 EHLO 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 MAIL 250 - - 2012-09-05 18:14:16 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 RCPT 250 - - 2012-09-05 18:14:48 209.85.223.175 mail-ie0-f175.google.com SMTPSVC1 MAILSVR 192.168.1.79 0 QUIT 240 - - However, if I sent from my personal Yahoo account, I get this response: Sorry, we were unable to deliver your message to the following address. <[email protected]>: Remote host said: 530 5.7.0 Must issue a STARTTLS command first [MAIL_FROM] (NB: Nothing appeared in the smtp log for this message.) Any suggestions where to start looking? EDIT ---- I don't know if it matters, but the certificate I am using for TLS is self signed.

  Read the article

• Windows network routing

  - by fabianvilers

  Hi! I'm working by my customer premises and they let me connect my private laptop on a dedicated Wi-Fi for internet access. It's nice for external consultants. The only issue is that we can't connect on a remote server on port 25. I suppose this policy is set up to avoid infected computers sending spam from their network. As you can have guessed, this is something weird that I can't send mail at all. Fortunately, I've a 3G cell phone that I can connect by Bluetooth on my laptop. So when I want to send an e-mail, I have to disconnect from Wi-Fi, connect my phone, send the e-mail, disconnect phone and reconnect Wi-Fi. Kinda overhead. My question is: how can I tell Windows 7 to use the Wi-Fi for every out connection, but if it's a connection on port 25, use the cell phone network? With this solution, I could let my phone connected all day without having to switch again and again. Thanks a lot for your anwwers. Fabian

  Read the article

• Mysql connections hanging in login state

  - by Mark Rose

  Suddenly today, I had an issue with connections to mysql hanging when connecting by IP address (e.g. mysql -h 10.1.248.20), but I could still connection using localhost fine, regardless the user. mysql> show processlist; +----+----------------------+------------------+------+---------+------+-----------------------------------------------------------------------+------------------+ | Id | User | Host | db | Command | Time | State | Info | +----+----------------------+------------------+------+---------+------+-----------------------------------------------------------------------+------------------+ | 1 | system user | | NULL | Connect | 10 | Connecting to master | NULL | | 2 | system user | | NULL | Connect | 10 | Has read all relay log; waiting for the slave I/O thread to update it | NULL | | 37 | unauthenticated user | 10.1.248.3:36694 | NULL | Connect | NULL | login | NULL | | 38 | unauthenticated user | 10.1.248.3:36695 | NULL | Connect | NULL | login | NULL | | 39 | unauthenticated user | 10.1.248.3:36696 | NULL | Connect | NULL | login | NULL | | 40 | root | localhost | NULL | Query | 0 | NULL | show processlist | +----+----------------------+------------------+------+---------+------+-----------------------------------------------------------------------+------------------+ 6 rows in set (0.00 sec) Yes, I realize replication was broken in that output above; that was after I tried restart MySQL (it was an emergency). And as suddenly as things stopped working, they started working again. DNS was working fine at the time. Replication was still working. MySQL was responsive. Does anyone have any idea what would cause MySQL logins from remote IPs to hang suddenly?

  Read the article

• Toshiba A205-5804 freezes when plugged in

  - by heron

  Well I have a Toshiba A205-5804 and the problem is that the screen freezes anytime I plug the pc into the external power supply, not as most of the computers having the same issue, my computer DOES freeze in safe mode, and I really can't bear this problem for much longer... It's not an overheating problem, the computer is not getting hot or anything related, I've already tried changing the AC adapter, booting only with AC and no battery, and also all of these suggestions: Try changing the following setting in the bios setup, under the 'Advanced' tab Dynamic CPU Frequency: Mode = Always Low (NOT DYNAMIC) My laptop has been running on AC power without a problem for 24hours, including many restarts, and when I went back to the original bios setting, the problem returned almost straight away. EDIT Other suggestions I found on the web from here and here: Set the power plan to high performance Set the power plan to "Minimal Power Management" (1 and 2 do conflict) Start - Control Panel - Device Manager -- Processor - disable one of two processors - reboot normally 4.Do this: Only plug battery into laptop Turn on the laptop and start Windows normally Plug AC adapter into laptop, the screen will freeze Leave the laptop the way it is for 12-24 hours After 12-24 hours, turn it off the hard way Once it is turned off, turn it back on. The laptop is working now. I have no idea of what can it be...

  Read the article

• do I need to create an AD site for VPN network

  - by ykyri

  I have Windows Domain level 2008 R2. There are four GC DC in four different physical locations. I have Kerio-based VPN network for replication and remote administration. Here is how network configured: dc1: local IP: 192.168.0.10 VPN IP: 192.168.1.10 dc2: local IP: 10.10.8.11 VPN IP: 192.168.1.11 dc3: local IP: 10.10.9.12 VPN IP: 192.168.1.12 dc4: local IP: 10.10.10.13 VPN IP: 192.168.1.13 That's simple, replication and all works fine but when running dcdiag on dc3 I have an error: A warning event occurred. EventID: 0x000016AF During the past 4.12 hours there have been 216 connections to this Domain Controller from client machines whose IP addresses don't map to any of the existing sites in the enterprise. <...> The log(s) may contain additional unrelated debugging information. To filter out the needed information, please search for lines which contain text 'NO_CLIENT_SITE:'. The first word after this string is the client name and the second word is the client IP address. Here is netlogon.log lines example: 05/30 12:07:39 DOMAIN.NAME: NO_CLIENT_SITE: dc2 192.168.1.11 05/31 09:52:11 DOMAIN.NAME: NO_CLIENT_SITE: dc4 192.168.1.13 05/31 19:49:31 DOMAIN.NAME: NO_CLIENT_SITE: adm-note 192.168.1.101 07/01 05:16:26 DOMAIN.NAME: NO_CLIENT_SITE: dc1 192.168.1.10 All VPN-joined computers are generates same log line as above. Computer amd-note is for example administrator's notebook, also have VPN. Question is should I add new AD site and bind VPN subnet 192.168.1.0/24 with that site?

  Read the article

• Hosting multiple websites from home

  - by dean nolan

  I have just been accepted for Microsofts Wevsite Spark program which I mainly got for the tools, Visual Studio, Blend. I also have a few of my own websites, personal and a couple of business ones. I also work freelance and sometimes I would like a place to just put a demo up of a clients project. The websites I currently have are all on differnet hosting provders and domain registrars. The WebsiteSpark comes with Windows Server 2008 and SQL Server 2008. It would be really advantagous of me to have all these in one place but also so I have complete control over the database and the environment. So I am thinking over the next 4-6 months of migrating all this to my own server that I will host from home, or maybe even setup at home and then store in a proper datacentre. I was wondering what steps I should take and what to be aware of, specifically: 1) having all these different websites on one computer and having the url got to the proper place. 2) Cost effectiveness? Having the server in home as apposed to datacentre. Most solutions I see charge over £1000 a month to have a machine in datacentre. This is mostly for my own ease of management and shared hosting which I currently have is very limited configuration wise. Would getting a server in house be beneficial for then upgrading to the cloud? What measures should I take with my ISP? I know this is a lot I've asked but just even links to good articles would be good. Thanks

  Read the article

• Strange ssh key issue

  - by user55714

  Scenario 1. I am doing this from /home/deploy directory I am trying to set up ssh with github for capistrano deployment. this has been an absolute nightmare. when I do ssh [email protected] as the deploy account I get Permission denied (publickey). so may be the key is not being found, so If I do a ssh-add /home/deploy/.ssh/id_rsa Could not open a connection to your authentication agent. (i did verify that the ssh-agent was running) If I do exec ssh-agent bash and then repeat the ssh-add then the key does get added and I can ssh into github. Now I exit from the ssh connection to my server and ssh back in and I can't ssh into github anymore! Scenario 2 if I login to my remote server and then cd into my .ssh directory and ssh into github then it all works fine I guess there is a problem with locating the key and for some reason the agent isn't funcitoning correctly. Any ideas? Her is a pastie with more details..my .bashrc, permissions etc. http://pastie.org/pastes/1190557/

  Read the article

• Installing sphinx on a web hosting server

  - by fiftyeight

  I want to install sphinx search on a web-hosting server. I'm on a Linux VPS with hostgator, but I never actually installed anything on a remote server so this will be a first time for me. If there's anyone here who installed sphinx it's really help me I had some problems when using sphinx on my PC with the permissions and the MySQL files, eventually I got it working on my PC. Anyway, I'd me really grateful if anyone can help me with some questions Do i need root access to install sphinx? I have root access to the server but I'd connect to it as a normal user since doing stuff as root is always less secure. can anyone tell me by what user I need to execute the indexer and the search daemon? Should I use root access in order to this? when I did it as a normal user on my PC it gave me some trouble with the PID file and the log files. last time I executed the search deamon I executed it as a normal user and it gave me some trouble, I created the folder /var/log/ for log files and did chmod 777 on it, but still when I executed the search daemon it created the PID file "searchd.pid" file but with no permissions for some reason, any idea why? Thanx in advance. fiftyeight

  Read the article

• Server not accepting uploads

  - by Tatu Ulmanen

  I'm having a strange problem with my VPS: I can download files from it, I can use PuTTy to connect to it and all behaves normally. But sometimes, when I try to upload a file to the server or save a file via SFTP, the connection inexplicably fails. I am using jEdit to edit files remotely via SFTP. When it works, it works fine. When it doesn't, I get an error message: Cannot save: java.io.IOException: inputstream is closed Cannot save: java.io.IOException: 4: I can see that a temporary save file (#file.php#save#) is created on the server with a filesize of 0. So the connection works, but when it comes to sending the actual data, something fails. The same thing with WinSCP, but the error is different: Copying file fatally failed. Copying files to remote side failed. And I can always browse the server with PuTTy without a problem. I see nothing abnormal in any log files. Auth.log shows this when I try to save: sshd[32638]: Accepted password for - from - port 62272 ssh2 sshd[32638]: pam_unix(sshd:session): session opened for user - by (uid=0) sshd[32640]: subsystem request for sftp sshd[32638]: pam_unix(sshd:session): session closed for user - When I wait for a while (say, an hour), everything works fine again. It can't be a temporary ban, as I am still allowed to connect to the server, right? I know this may not be enough info to solve the problem, but I am grateful for any clues or bits of information that might help me. What are the possible causes for this kind of behaviour, what log files can I check for clues etc.. I'm running out of ideas!

  Read the article

• PST backup with Volume Shadow Copy Service

  - by NoMadMan

  I was asked to implement the task of backing up 35 PST files ranging from 800Mb to 2000Mb. Windows XP and Windows 2000 workstations are assigned to the users and we have a Windows 2000 domain controller we use to back up files on 3x 500Gb external hard drives. I found several methods from applications to scripts. Local or remote applications would be my last resort. I came across this script based on Volume Shadow Copy Service. CopyWithVss I wanted to know if there would be a problem if the path had spaces. Would mounting the destination path of each PST folder with a drive letter be more practical? My concern with mounting option is that i would eventually run out of letters since I have 35 and possibly more workstations to back up. Lastly, can someone give me an example of CopyWithVss if it were run on a production network? The script is a bit cryptic even after reading several times. Where in the script do I enter the source and the destination? I'm a Mac user so please excuse my ignorance with Windows platform.

  Read the article

• Merely installing PHP5 causes my AWS Ubuntu server to die minutes later from a massive CPU spike

  - by Mark Amery

  I have an AWS server with Ubuntu 11.04 as the OS that is running an Apache2 webserver (incidentally Python-based and using Django). We recently needed to add support for php5 to let us use a third party PHP library (incidentally for serving minified versions of js and css files). However, for no reason any of us can discern, if we simply run sudo apt-get install php5 on the server, then the install appears to finish successfully but, without us taking any further action (including not yet running sudo apt-get install libapache2-mod-php5, which I think would be the next step for us if everything worked), or actually running any PHP scripts on the server, a few minutes later the server becomes impossible to connect to, and looking at the 'Monitoring' tab for the server in the EC2 Management Console reveals that a while after the installation, CPU usage spikes to 100% and stays there permanently (until we reboot the server from the AWS Console). After rebooting, the server also reliably dies within a few (between 0 and 10) minutes. We restored the server to a pre-PHP state from an AMI Image, observed that it was stable, and then tried installing PHP5 again and observed the server die in exactly the same way, so we're pretty much certain that installing PHP5 is what causes the symptoms. What on earth could be causing this behaviour, and how can we get PHP installed on the server without it dying?

  Read the article

• LXC, Port forwarding and iptables

  - by Roberto Aloi

  I have a LXC container (10.0.3.2) running on a host. A service is running inside the container on port 7000. From the host (10.0.3.1, lxcbr0), I can reach the service: $ telnet 10.0.3.2 7000 Trying 10.0.3.2... Connected to 10.0.3.2. Escape character is '^]'. I'd love to make the service running inside the container accessible to the outer world. Therefore, I want to forward port 7002 on the host to port 7000 on the container: iptables -t nat -A PREROUTING -p tcp --dport 7002 -j DNAT --to 10.0.3.2:7000 Which results in (iptables -t nat -L): DNAT tcp -- anywhere anywhere tcp dpt:afs3-prserver to:10.0.3.2:7000 Still, I cannot access the service from the host using the forwarded port: $ telnet 10.0.3.1 7002 Trying 10.0.3.1... telnet: Unable to connect to remote host: Connection refused I feel like I'm missing something stupid here. What things should I check? What's a good strategy to debug these situations? For completeness, here is how iptables are set on the host: iptables -F iptables -F -t nat iptables -F -t mangle iptables -X iptables -P INPUT DROP iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p icmp --icmp-type echo-request -j ACCEPT iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -t nat -A POSTROUTING -o lxcbr0 -j MASQUERADE iptables -t nat -A PREROUTING -p tcp --dport 7002 -j DNAT --to 10.0.3.2:7000

  Read the article

• IP addresses not listed for IIS website bindings

  - by Svinn

  Recently purchased a windows cloud server godaddy. Now i installed iis7 and all other required software. And i have 50.62.1.89 and 2 more public ips. Also i have a private ip 10.1.0.2. Now the problem is am unable to access any website through any public ip. All my public ips are opening default website only. also i cant see pubic ips for IIS website bindings. Only my private ip listed for IIS binding. And in my server also public opening only default website. But am able to open websites using private ip. But my public ip addresses pointed to my server correctly. am able to open my server using remote desktop using public ip. Also as i said already public ip opening default website from IIS without problem. Please help me. Am confused for last 2 days.

  Read the article

• Recommended drive encryption solution

  - by Chris Driver

  Hello, I will soon be purchasing a number of laptops running Windows 7 for our mobile staff. Due to the nature of our business I will need drive encryption. Windows BitLocker seems the obvious choice, but it looks like I need to purchase either Windows 7 Enterprise or Ultimate editions to get it. Can anyone offer suggestions on the best course of action: a) Use BitLocker, bite the bullet and pay to upgrade to Enterprise/Ultimate b) Pay for another 3rd party drive encryption product that is cheaper (suggestions appreciated) c) Use a free drive encryption product such as TrueCrypt Ideally I am also interested in 'real world' experience from people who are using drive encryption software and any pitfalls to look out for. Many thanks in advance... UPDATE Decided to go with TrueCrypt for the following reasons: a) The product has a good track record b) I am not managing a large quantity of laptops so integration with Active Directory, Management consoles etc is not a huge benefit c) Although eks did make a good point about Evil Maid (EM) attacks, our data is not that desirable to consider it a major factor d) The cost (free) is a big plus but not the primary motivator The next problem I face is imaging (Acronis/Ghost/..) encrypted drives will not work unless I perform sector-by-sector imaging. That means an 80Gb encrypted partition creates an 80Gb image file :(

  Read the article

• Industrial strength cloud file storage

  - by ArthurG

  I'm looking for an industrial strength cloud file storage system. It will be used by multiple people in a startup. Our requirements: Transparent file system access: files and folders in the file system must be able transparently access (read and write) files in the cloud; files must be synchronized whenever network access is available and buffered otherwise. The system must be usable by non-technical people. Access control: we need to control who can access which files, at least on a very coarse basis. e.g., the developers will be able to access the system design documents, only the corporate folks can access recruiting documents, and only management can access certain corporate documents. Dropbox provides this via Sharing folders, but that's not adequate, if I understand it correctly, because there's no authentication of the sharing user. so the cloud service should have a notion of an account (our startup) with multiple users with distinct credentials and rights for each user Clients: it must be accessible from Macs and PCs; I would hope that it supports Linux (e.g., Ubuntu) too Security: it must provide robust security Backup: the cloud service must reliably backup the files Versioning: change version history, is a big plus, but not required Not free: we're willing to pay for the service So far, we've reviewed the following, albeit not completely thoroughly: Dropbox: has all except 1) Access control, which is provided via Sharing folders, but that's not adequate, if I understand it correctly, because there's no authentication of the sharing user. and 2) Security, as discussed here http://www.economist.com/blogs/babbage/2011/05/internet_security and here http://blog.dropbox.com/?p=821. Windows Live Mesh, has all except 1) Clients, only supporting Windows 7 and OS X. SpiderOak has all, except 1) Transparent file system access, which is only available for 1 user. Amazon Cloud, doesn't offer 1) Transparent file system access Rackspace Cloud Drive has all except 1) Access control and 2) Versioning I'll gladly include any clarifications or additional systems the community provides. Arthur

  Read the article

• How do I repartition an SDHC card in Windows?

  - by Peter Mortensen

  How do I repartition an SDHC card (4 GB or more)? Do I need third-part tools or Linux (a live CD solution would be OK)? In Windows' Disk Management the option Delete Partition is dimmed out: I can reformat the card as FAT32, copy files to and from the card and even change the file system to NTFS using the command line command CONVERT, but not repartition it. The article How to Partition an SD Card in Windows XP talks about using "a Windows enabler program" which sound rather dubious to me. I have tried to change from “Optimize for quick removal” to “Optimize for performance”. The option to format as NTFS appeared, but the Delete Partition option is still dimmed out. Platform: Windows XP 64-bit SD card reader: USB 2.0 device, LogiLink® CR0005C Cardreader 3,5' USB 2.0 intern 54-in-1 mit USB Front Kingston 16 GB SDHC card, speed class 4. (It could be formatted as FAT32 and successfully used in a 4 GB ReadyBoost setup (Windows 7).) I have also tried on different versions of Windows and with different cards with the same result: Kingston 4 GB SDHC card, speed class 4 (the one shown in the screenshot) Transcend 2 GB (not marked as SDHC, but SD) Windows 7 32-bit (albeit with a somewhat an older card reader) and Windows XP 32-bit on an EliteBook 8730w

  Read the article

< Previous Page | 696 697 698 699 700 701 702 703 704 705 706 707  | Next Page >