Search Results

Search found 20816 results on 833 pages for 'vsphere client'.

Page 710/833 | < Previous Page | 706 707 708 709 710 711 712 713 714 715 716 717  | Next Page >

• IPv6 works only after ping to routing box

  - by Ficik

  Situation: There is ipv4 only router in network and every computer is connected to it (wifi or cable). Server with ipv4 and ipv6 is connected to this router as well. Server has configured tunnelbrokers 6to4 tunnel and radvd. Clients in network has right prefix and can ping each other. But they can't ping to internet until they ping Server (the one with tunnel). I found somewhere that it's icmp problem, but I couldn't find solution. Is it problem that there is ipv4 only router? server and client runs linux router runs dd-wrt without ipv6 support :( Ping try: standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes ^C --- ipv6.google.com ping statistics --- 29 packets transmitted, 0 received, 100% packet loss, time 28223ms standa@standa-laptop:~$ ping6 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 PING 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478(2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478) 56 data bytes 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=1 ttl=64 time=3.55 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=2 ttl=64 time=0.311 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=3 ttl=64 time=0.269 ms 64 bytes from 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478: icmp_seq=4 ttl=64 time=0.292 ms ^C --- 2001:470:XXXX:XXXX:21c:c0ff:fe2b:6478 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3000ms rtt min/avg/max/mdev = 0.269/1.107/3.559/1.415 ms standa@standa-laptop:~$ ping6 ipv6.google.com PING ipv6.google.com(2a00:1450:8007::69) 56 data bytes 64 bytes from 2a00:1450:8007::69: icmp_seq=1 ttl=57 time=20.7 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=2 ttl=57 time=20.2 ms 64 bytes from 2a00:1450:8007::69: icmp_seq=3 ttl=57 time=23.4 ms ^C --- ipv6.google.com ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2001ms rtt min/avg/max/mdev = 20.267/21.479/23.413/1.392 ms

  Read the article

• Open an X application going through many hoops (SSH, vpn etc)

  - by ??O?????

  The players: my home computer, running Linux with an X server running. (Call it HOME.) a remote site, to which I can connect over the internet using a VPN. (SITE) a Linux computer at the remote site, to which I can connect with ssh -X and nicely have X clients displaying on my local server. (MIDDLE) a very old Irix machine (an Onyx) at the remote site, which has no SSH server (therefore I can't ssh -X to it), only an ssh client. (ONYX) Purpose I need to run an X11 application on the ONYX machine, and see the GUI on HOME. I think I stumble upon xauth issues. So far The current situation is: ? HOME connects to SITE ? A vncserver starts on MIDDLE:7 ? vncviewer on HOME connects to vncserver on MIDDLE ? ONYX starts a forwarding ssh session to MIDDLE: ssh -TfN -L 6007:127.0.0.1:6007 MIDDLE ? DISPLAY=localhost:7 xclient on ONYX fails with Xlib: connection to "127.0.0.1:7.0" refused by server I do know that the forwarding (6007:127.0.0.1:6007) succeeds. A previous attempt was: ? HOME connects to SITE ? HOME connects to MIDDLE: ssh -X MIDDLE (xclock displays on HOME, DISPLAY is 127.0.0.1:10) ? ONYX starts an SSH tunnel to MIDDLE: ssh -TfN -L 6010:127.0.0.1:6010 MIDDLE ? DISPLAY=127.0.0.1:10 xclient fails with X connection to 127.0.0.1:10.0 broken (explicit kill or server shutdown). while an error pops up in the MIDDLE session: X11 connection rejected because of wrong authentication. Despair How can I achieve my purpose?

  Read the article

• Symantec Antivirus Corporate -- two problems

  - by Alex C.

  We have a Windows network with a domain and about 50 clients. A few months ago, we installed Symantec Antivirus, Corporate Edition ver. 10.1.8.8000. There are two problems. The larger problem is that the software isn't very good at stopping viruses. In the last month, four different machines have become infected with those viruses that masquerade as antivirus software. Two machines I was able to clean with MalWareBytes. The other two were hopeless, and I had to reinstall Windows. Is there something I can do to make the Symantec product more effective? As far as I can tell, it successfully updates definitions nightly and pushes the definitions to the clients. The smaller problem is that the Symantec client applications sometimes initiate scans at random (and inappropriate) times. One of my co-workers complained to me yesterday that her computer was running very slow. I looked at the scan history and found that Symantec had scanned the computer three times during the past two days, and each time during the workday. No threats were found. Not sure why it's doing this, but I'd like it to stop. Any help would be appreciated. Thanks.

  Read the article

• Unable to ssh in Beagle Bone Black

  - by SamuraiT

  I wanted to install pip onto beagle bone black,and I tried this: /usr/bin/ntpdate -b -s -u pool.ntp.org opkg update && opkg install python-pip python-setuptools then, it threw errors,but Unfortunately, I didn't log that errors. it was occurred a week ago and was't solved yet. I wanted to solve it now and I tried connect by ssh,but I failed. When I ping to beagle bone, it responds, and Cloud9 IDE is working too but not ssh. I don't think this is serious problem since I can connect to beagle bone by other methods: Cloud9 or so. However, to use python on beagle bone, I need to connect by ssh. Before trying to update and install python-pip, I could connect by ssh. Do you have any ideas to solve this connection problem? note I use default OS: Angstrom I don't use SD card. HOST PC is mac, OS.X 10.9 connect by USB serial I checked this but this wasn't helpful http://stackoverflow.com/questions/19233516/cannot-connect-to-beagle-bone-black I could connect by GateOne SSH client, but still unable to connect from terminal.

  Read the article

• Set primary group of file or directory on Samba share from Windows

  - by Hubert Kario

  Short version: I have such situation on a Samba share: $ ls -lha total 12K drwxr-xr-x 3 hka Domain Users 4.0K Jan 11 17:07 . drwxrwxrwt 19 root root 4.0K Jan 11 17:06 .. drwxr-xr-x 2 hka Domain Users 4.0K Jan 11 17:07 dir A -rw-r--r-- 1 hka Domain Users 0 Jan 11 17:07 file A How am I able to change this to following using only Windows SMB/CIFS client (using 3rd party applications is OK) $ ls -lha total 12K drwxr-xr-x 3 hka Domain Users 4.0K Jan 11 17:07 . drwxrwxrwt 19 root root 4.0K Jan 11 17:06 .. drwxr-xr-x 2 hka ntpoweruser 4.0K Jan 11 17:07 dir A -rw-r--r-- 1 hka ntpoweruser 0 Jan 11 17:07 file A Rationale and background info I'm using POSIX ACLs on Samba shares. Together with acl group control for Samba, it allows me to delegate management of permissions to different users based on group membership. Thing is, when I create a new file on a Samba share, I'm unable to set its primary group (the one that grants permission to change its permissions). It's being set to my primary group (Domain Users) or group set using force group option in smb.conf share definition. Removing all groups in windows except the one I want to become the new primary group doesn't work. I can change it using chgrp group folder/ as regular user though shell, but it's suboptimal (not all users are *nix users). Trying to set new owner to group from Windows file permission window makes the Samba to return permission denied with following log entry: [2012/01/05 21:13:03.349734, 3] smbd/nttrans.c:1899(call_nt_transact_set_security_desc) call_nt_transact_set_security_desc: file = projects/project A/New folder, sent 0x1 [2012/01/05 21:13:03.349774, 3] smbd/posix_acls.c:1208(unpack_nt_owners) unpack_nt_owners: unable to validate owner sid for S-1-5-21-4526631811-884521863-452487935-11025 [2012/01/05 21:13:03.349804, 3] smbd/error.c:80(error_packet_set) error packet at smbd/nttrans.c(1909) cmd=160 (SMBnttrans) NT_STATUS_INVALID_OWNER The SID is correct and belongs to group I specified in GUI.

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• "Dictionary problem." Error with VMPlayer

  - by George Mauer

  I'm pretty new to using vmware virtualization (been a virtualbox user) so I'm hoping you guys can help me out. I recently got an external usb disk containing a vm for a client, downloaded vmplayer, set it up with "Open a Virtual Machine", ran it, easy as pie. After working with it a bit this morning, I shut the VM down and now trying to start it back up again I get this: I tried removing the vm from my library, now it happens whenever I try to add it back in. In the meantime, I can still access other virtual machines so it seems like the problem might be with the virtual disk. So two questions: This is obviously not a very helpful error message. Where can I go to get more information? My Application EventLog doesn't contain anything from VMWare. What steps can I take to fix the problem? Edit: A couple more pieces of information. I did not take any snapshots. I don't think VM Player even has that ability. I have a zip file of (what I assume) is the state of the VM when it was sent to me. I cannot unzip it as it is huge and simply requires more HD space than I have available but I did extract the vmx file and examine it. Other than the UUIDs and the fact that mine reads cleanShutdown = "FALSE" they are identical. The log contains the following lines Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead: Unable to load dict from 'E:....\MachineName.vmsd'. Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead failed for file 'E:....\MachineName.vmx': Dictionary problem (6) Jun 23 10:11:18.082: vmx| SNAPSHOT: Snapshot_TimeStampTiers failed: Dictionary problem (6)

  Read the article

• ldap-authentication without sambaSamAccount on linux smb/cifs server (e.g. samba)

  - by umlaeute

  i'm currently running samba-3.5.6 on a debian/wheezy host to act as the fileserver for our department's w32-clients. authentication is done via OpenLDAP, where each user-dn has an objectclass:sambaSamAccount that holds the smb-credentials and an objectclass:shadowAccount/posixAccount for "ordinary" authentication (e.g. pam, apache,...) now we would like to dump our department's user-db, and instead use authenticate against the user-db of our upstream-organisation. these user-accounts are managed in a novell-edirectory, which i can already use to authenticate using pam (e.g. for ssh-logins; on another host). our upstream organisation provides smb/cifs based access (via some novell service) to some directories, which i can access from my linux client via smbclient. what i currently don't manage to do is to use the upstream-ldap (the eDirectory) to authenticate our institution's samba: i configured my samba-server to auth against the upstream ldap server: passdb backend = ldapsam:ldaps://ldap.example.com but when i try to authenticate a user, i get: $ smbclient -U USER \\\\SMBSERVER\\test Enter USER's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.6.6] tree connect failed: NT_STATUS_ACCESS_DENIED the logfiles show: [2012/10/02 09:53:47.692987, 0] passdb/secrets.c:350(fetch_ldap_pw) fetch_ldap_pw: neither ldap secret retrieved! [2012/10/02 09:53:47.693131, 0] lib/smbldap.c:1180(smbldap_connect_system) ldap_connect_system: Failed to retrieve password from secrets.tdb i see two problems i'm having: i don't have any administrator password for the upstream ldap (and most likely, they won't give me one). i only want to authenticate my users, write-access is not needed at all. can i go away with that? the upstream ldap does not have any samba-related attributes in the db. i was under the impression, that for samba to authenticate, those attributes are required, as smb/cifs uses some trivial hashing which is not compatible with the usual posixAccount hashes. is there a way for my department's samba server to authenticate against such an ldap server?

  Read the article

• Setting up apache vhost for Icinga

  - by DKNUCKLES

  It's been a while since I've worked with Apache so please be kind - I'm also aware of this question but it hasn't been much help to me. I'd like to set up a simple vHost w/ Apache for my Icinga instance. Icinga is up and running and I can access it from x.x.x.x/icinga, however would like to be able to access it externally as well as internally. I have set up the /etc/hosts file and the following is my barebones vhost statement in httpd.conf <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /usr/share/icinga ServerName icinga.domain.com ErrorLog logs/icinga.com-error_log CustomLog logs/dummy-host.example.com-access_log common </VirtualHost> I also have the following in my .htaccess file <Directory> Allow From All Satisfy Any </Directory> An entry has been made for the instance in the Windows DNS server on my network, however when I try to access the site by URL I am greeted with Internal Server Error. Reviewing the /var/log/icinga.com-error_log I see the following entry. [Thu Dec 13 16:04:39 2012] [alert] [client 10.0.0.1] /usr/share/icinga/.htaccess: <Directory not allowed here Can someone help me spot the error of my ways?

  Read the article

• How to setup ping between XP guest from Win8 Host using Hyper-V virtual swtich

  - by rism

  Hyper-V client is installed on a Win8 Pro 64 bit box and a VM running XP has been created within that with an internal virtual swtich. The VM can be booted and accessed and there is a default virtual NIC within it with dynamic IP of 169.254.x.x which i have changed to be a static IP of 192.168.0.12/255.255.255.0 confirmed via ipconfig on the XP guest. The Host has IP of 192.168.0.7/255.255.255.0. Both host and guest have their firewalls disabled for simplicity. I cant ping guest from host nor host from guest. TTL timeout. And with regard to Hyper-V and VMs I dont know what to do next. Both are in same workgroup (as per name) but since they cant ping I guess that means nothing. .... My objective is to share a folder on VM so I can install a 32bit accountancy app that wont run on Win8/7 so if there is a more simplistic way then Im all ears but typically a peer to peer is very simple.

  Read the article

• Cache Control Headers with IIS 7.5

  - by Brad

  I'm trying to wrap my head around client side (web browser) caching and how it works in relation to IIS 7.5 cache control headers. In particular: If we want to force clients to reload cached resources, how must IIS be configured? Do we need to set expire web content immediately if the resources on the server have a more recent Modified Date (or ETag value)? Right now we're not setting any cache headers. So if I set a cache header of no-cache (which I think is the equivalent of expire web content immediately) will that force the web browser to obtain a new version of a particular file. Or will the browser only request a new version after it deems its current copy to be stale and then from that point forward not cache it? Would a best practice be to set a cache control flag of 1 week, then 8 days before I know I am going to make a change set the cache control down to for instance 30 minutes? But if I do that and then need to immediately expire an item from users caches because there was an issue with it how do I do that?

  Read the article

• What may the reason of slowness be (see details in message body)?

  - by Ivan

  I've got a really weird situation I'm beating to solve. A performance problem which looks really like an empty waiting sequence set in code (while it probably isn't so). I've got a pretty powerful dedicated server (10 GB RAM, eight Xeon cores, etc) running Ubuntu 10.04 with all the functionality services (except OpenVPN server used to provide secure access to clients) deployed in separate VirtualBox (vboxheadless) machines (one for the company e-mail server, one for web server and one for accounting/crm server (Firebird + proprietary app server working with Delphi-made clients)). CPU load (as "top" says) is almost always near zero. Host system RAM is close to 100% usage but not overloaded (as very little swapping gets used, and freed (by stopping one of VMs) memory doesn't get reused any quickly). Approximately 50% of guests RAM is used. iostat usually shows near zero %util. Network bandwidth seems to be underused. But the accounting/crm client (a Win32 Delphi application run on WinXP machines) software works hell-slow with this server (and works much better using an inside-LAN Windows server). I just can't imagine what can make it be slow if there are so plenty of CPU, RAM, HDD and bandwidth resources available on clients and on the server even in their hardest moments. Saying bandwidth is underused I not only know that clients and the server are connected to the Internet with a bigger channels than really used (which leaves the a chance they may have a bottleneck of a sort on the route between them), I've tested bandwidth between clients and the server by copying files among them.

  Read the article

• iptables drops some packets on port 80 and i don't know the cause.

  - by Janning

  Hi, We are running a firewall with iptables on our Debian Lenny system. I show you only the relevant entries of our firewall. Chain INPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW Chain OUTPUT (policy DROP 0 packets, 0 bytes) target prot opt in out source destination ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOGDROP all -- * * 0.0.0.0/0 0.0.0.0/0 Some packets get dropped each day with log messages like this: Feb 5 15:11:02 host1 kernel: [104332.409003] dropped IN= OUT=eth0 SRC= DST= LEN=1420 TOS=0x00 PREC=0x00 TTL=64 ID=18576 DF PROTO=TCP SPT=80 DPT=59327 WINDOW=54 RES=0x00 ACK URGP=0 for privacy reasons I replaced IP Addresses with and This is no reason for any concern, but I just want to understand what's happening. The web server tries to send a packet to the client, but the firewall somehow came to the conclusion that this packet is "UNRELATED" to any prior traffic. I have set a kernel parameter ip_conntrack_ma to a high enough value to be sure to get all connections tracked by iptables state module: sysctl -w net.ipv4.netfilter.ip_conntrack_max=524288 What's funny about that is I get one connection drop every 20 minutes: 06:34:54 droppedIN= 06:52:10 droppedIN= 07:10:48 droppedIN= 07:30:55 droppedIN= 07:51:29 droppedIN= 08:10:47 droppedIN= 08:31:00 droppedIN= 08:50:52 droppedIN= 09:10:50 droppedIN= 09:30:52 droppedIN= 09:50:49 droppedIN= 10:11:00 droppedIN= 10:30:50 droppedIN= 10:50:56 droppedIN= 11:10:53 droppedIN= 11:31:00 droppedIN= 11:50:49 droppedIN= 12:10:49 droppedIN= 12:30:50 droppedIN= 12:50:51 droppedIN= 13:10:49 droppedIN= 13:30:57 droppedIN= 13:51:01 droppedIN= 14:11:12 droppedIN= 14:31:32 droppedIN= 14:50:59 droppedIN= 15:11:02 droppedIN= That's from today, but on other days it looks like this, too (sometimes the rate varies). What might be the reason? Any help is greatly appreciated. kind regards Janning

  Read the article

• Certain websites redirect to 127.0.0.1. How do I fix this?

  - by Dian

  Facebook and Youtube in particular. Tried nslookup the address shows as 127.0.0.1. Checked the HOSTS file, it's fine. Ran Malwarebytes' Anti-Malware (didn't find any problems) and SpyBot Search and Destroy (found 1 problem). (Not sure if the Spybot made this improvement) now pinging youtube shows the correct address (74.125.71.91) but the browser still says: Connection to 127.0.0.1 Failed The system returned: (111) Connection refused Tried ipconfig /flushdns but there are no changes. Switched to another user but the results are the same. hosts file: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost ipconfig all: Connection-specific DNS Suffix: DNS Servers: 10.1.1.30 208.67.220.220

  Read the article

• How to speed up request/response to django using apache or another solution?

  - by jbcurtin

  Hey all, I'm mainly a developer, but every now and again I jump into the sys-admin position. For the most part I've gotten away with deploying php and python apps using apache. I write today because I'm starting to research faster alternatives to apache, yet still have some of the core features I require like put and delete methods and the ability to connect to a socket via apache. ( This I have not tried, but might be a nice whistle if I ever employ comet on my apps. ) As you've probably guessed, I use javascript exclusively for all my websites utilizing deep linking for SEO support. The main areas that I'm looking to increase performance is the connection between the django apps and the web server to the client response. Every day I work my best to keep the smallest memory foot print as possible, however I am getting to the end of my rope when it comes to working with apache. In general, keep in mind that I'm just starting this research so I'm looking more for material to read then solutions at this moment. My main questions: Am I missing something about apache that makes it faster then everything else? What would be a good server environment to deploy just static files one? What are some of the leading open-source and paid alternatives?

  Read the article

• Tell if IIS is being asked to serve compressed pages?

  - by Graham

  Hi, I'm trying to find out if our IIS server is being asked to serve pages compressed. I'm a noob regarding a lot of this so am working my way through the issues. We're using IIS 6.0 and have correctly turned compression on. If I use Fiddler2 to analyse the HTTP requests via localhost, then Fiddler reports that the pages are compressed. If we then access the server over the network, either via its external URL or via the internal server name, Fiddler reports those pages as uncompressed. Therefore, it's logical to assume that something is getting in the way - presumably our ISA server. Our ISA administrator states that ISA is configured to allow compressed requests but what I want to do is to look at the requests coming through to IIS to see if IIS is being asked to serve pages compressed. I'm fairly convinced that our request is going to ISA, ISA is forwarding these, but not with the "compression" details - therefore IIS is not performing any compression. I've looked at the IIS logs but can't see anything obvious about the HTTP request. Is there any way I can check, on the web server itself, this sort of information? One thing that is confusing, but it may be normal, is that the Client IP making the request is not the orignal PC (i.e. mine) and not the ISA firewall, but the web server itself... Thanks

  Read the article

• Apache: Isn't chmod 755 enough to set up symlink or alias on Apache httpd on Mac OS 10.5?

  - by eed3si9n

  On my Mac OS 10.5 machine, I would like to set up a subfolder of ~/Documents like ~/Documents/foo/html to be http://localhost/foo. The first thing I thought of doing is using Alias as follows: Alias /foo /Users/someone/Documents/foo/html <Directory "/Users/someone/Documents/foo/html"> Options Indexes FollowSymLinks MultiViews Order allow,deny Allow from all </Directory> This got me 403 Forbidden. In the error_log I got: [error] [client ::1] (13)Permission denied: access to /foo denied The subfolder in question has chmod 755 access. I've tried specifying likes like http://localhost/foo/test.php, but that didn't work either. Next, I tried the symlink route. Went into /Library/WebServer/Documents and made a symlink to ~/Documents/foo/html. The document root has Options Indexes FollowSymLinks MultiViews This still got me 403 Forbidden: Symbolic link not allowed or link target not accessible: /Library/WebServer/Documents/foo What else do I need to set this up? Solution: $ chmod 755 ~/Documents In general, the folder to be shared and all of its ancestor folder needs to be viewable by the www service user.

  Read the article

• Configuration of Server root email - Change Address and Name on outgoing email

  - by JTWOOD

  As a newbie Postfix user, I've gotten so far and now I am stuck with a SMALL problem. I would like to configure my local network servers to send alerts and like using the following: 1) From address: [email protected] 2) From name: Hostname I can get #1 to work fine using smtp_generic_maps The problem is that on my email client, the name is listed as "root" - as in the header shows the following: Date: Sun, 29 Jul 2012 13:21:01 -0400 (EDT) From: [email protected] (root) To: undisclosed-recipients:; I'd like to change it to "From: [email protected] (Zeus)" I imagine that this can be done in the headers_check, but so far I haven't gotten anything to work and before I waste a ton of time trying to get this to work, I'd like to make sure I am on the right track. My aliasing and genericmaps are set up correctly (As far as I can see and know - the results are correct!). I just want to change that last bit in the From field to reflect the hostname. I would also like to add something in the subject of the outgoing messages for easy filtering - something like Subject: [Zeus.domain] - "Original Subject" Any suggestions are much appreciated. Thanks!

  Read the article

• How do I troubleshoot nginx not recognizing passenger?

  - by Jade

  Issue: nginx does not seem to recognize my rails application Symptoms: When the server starts up, it shows the "Welcome to nginx!" message instead of my Rails application. Nginx seems to be using the local nginx path instead of the Rails root I specified: 2010/04/18 06:29:06 [error] 783#0: *1 "/usr/local/nginx/html/blog/index.html" is not found (2: No such file or directory), client: 1.2.3.4, server: www.farmerjade.com, request: "GET /blog/ HTTP/1.1", host: "www.farmerjade.com" I used [RVM and Passenger Setup on NGINX][1] to install nginx and passenger on a virtual machine. Here is my nginx configuration: user farmerjade; worker_processes 1; ... http { include mime.types; default_type application/octet-stream; passenger_ruby /home/farmerjade/.rvm/bin/passenger_ruby; passenger_root /home/farmerjade/.rvm/gems/ree-1.8.7-head/gems/passenger-2.2.11; ... server { listen 80; server_name www.farmerjade.com; root /home/farmerjade/farmerjade/public; passenger_enabled on; rails_env development; ... I'd appreciate any help anyone has to offer -- I'm quite new to nginx.

  Read the article

• How do you apply proxy settings per computer instead of per user?

  - by Oliver Salzburg

  So far, I've used a user group policy object utilizing Internet Explorer maintenance to set a proxy for the user in IE. We have now deployed the Enterprise Client (EC) starter group policy to our domain and this policy affects this behavior. The EC group policy uses the policy Make proxy settings per-machine (rather than per-user). This policy describes itself as: This policy is intended to ensure that proxy settings apply uniformly to the same computer and do not vary from user to user. Great! This seems to be an improvement over my previous setup. If you enable this policy, users cannot set user-specific proxy settings. They must use the zones created for all users of the computer. What zones and where do I configure the proxy settings for them? I assumed the policy would simply take the user settings and apply them, but that's not what's happening. Now no proxy server is set at all. So my previous settings obviously no longer have any effect. So far, I've only come up with solutions that involved direct manipulation of the Windows registry. Which is fine, I guess, but the way the proxy is configured for users makes it appear as if there could be a higher level approach.

  Read the article

• How to access XAMPP virtual hosts from iPad on local network?

  - by martin's

  Using XAMPP on one machine. Multiple virtual hosts defined. One per project. Format is .local For example: apple.local microsoft.local client-site.local our-own-internal-site.local All works perfectly from that one machine. I now want to have other systems within the network access the various sites. The main reason for wanting to do this is to be able to test site functionality and layout from mobile devices without having to upload partial work to public servers. I can access the main XAMPP default site by simply entering the IP address of the XAMPP machine in, say, Safari on an iPad. However, there is no way to reach .local that I can see. Would this entail setting up a DNS server within the network? We have a mixture of Windows and Mac machines. No Linux. The XAMPP machine is Vista 64. I don't want real external internet access to be affected in any way, just ".local" pointed to the XAMPP machine if that makes sense.

  Read the article

• Have to run auto-negotiate between clients and switch - "old" switch works fine - "new" switch results in "port flapping"?

  - by ConfusedAboutSwitching

  I need some help understanding a problem we're having at work: We run Altiris/Deployment Solution and have to use auto-negotiate between client systems and our switches (Altiris apparently requires this for imaging, PXE boot and other functions). We have several areas with old wiring (Cat 3 & Cat 5) that have old 10/100 Cisco switches in them - and we can set these systems up to "auto/auto" (auto-negotiate on both the NIC and the switch port), and everything has been working fine. But - our networking crew changed out a couple of old switches for 10/100/1000 Cisco switches, and now - they are claiming that "auto/auto" won't work because the switches can't auto-negotiate the way the old 10/100 switches did - and that if we try to set the new gig switches to auto-negotiate, the switch port starts "port flapping", and shuts the port down. But - if we put the old switch back in - they work using "auto/auto" just fine - no port flapping. The networking crew is telling me that the problem is that we're putting "new switches" on "old wire", and that the old cabling can't/won't support the auto-negotiation with these new switches....??? There's something about this that doesn't make sense to me - can someone explain this to me? Or is our networking crew just doing something wrong in the configuration of these new switches? While will the old switches work "auto/auto", but the new switches won't?? HELP!!....and Thanks!! M

  Read the article

• Lotus Notes 8.0.2 - how to stop all mail showing in customized view

  - by mikolajek

  I am using Lotus Notes 8.0.2 at work and unfortunately the admin restricted changing default folders design. Only little changes are possible (e.g. change columns order) and even them are resetted each time I restart the client. I've created a new view with my desired column order, changed sorting etc. I have only one problem - even though I changed the "view" preference to show messages from the inbox folder only, I keep seeing all mail, regardless of the folder they are placed into. I'm not a Lotus expert and don't really know how to code. Yet, I am surprised as I see in a "simple view" this: uses '(ChangeMeetingType), ...' form AND In folder 'Inbox' And in Formula view only this: SELECT ((Form = "(ChangeMeetingType)") | (Form = "(Return Receipt)") | (Form = "Return Receipt") | (Form = "(ReturnNonReceipt)") | (Form = "ReturnNonReceipt") | (Form = "Memo") | (Form = "Memo") | (Form = "MemoEA") | (Form = "Reply") | (Form = "Reply") | (Form = "Reply With History") | (Form = "Reply With History") | (Form = "To Do") | (Form = "Task") | (Form = "_Document Memo") | (Form = "$DocMemo") | (Form = "Word. Document$Word Memo") | (Form = "WordPro. Document$Word Pro Memo") | (Form = "AlternateMemo")) Therefore, it looks like no folder has been really selected. How can I create a solution to see: Inbox contents only? Just messages, invitations and other "normal" stuff - without calendar entries and contacts?

  Read the article

• windows: force user to use specific network adapter

  - by Chad

  I'm looking for a configuration/hack to force a particular application or all traffic from a particular user to use a specific NIC. I have an legacy client/server app that has a "security feature" that limits connections based on IP address. I'm trying to find a way to migrate this app to a terminal server environment. The simple solution is for the development team to update the code in the application, however in this case that's not an option. I was thinking I might be able to install VMware NIC's installed for each user on the terminal server and do some type of scripting to force that user account to use a specific NIC. Anybody have any ideas on this? EDIT 1: I think I have a hack to work around my specific problem, however I'd love to hear of a more elegant solution. I got lucky in that the software reads the server IP address out of a config file. So I'm going to have to make a config file for each user and make a customer programs files for each user. Then add a VMware NIC for each user and make each server IP address reside on a different subnet. That will force the traffic for a particular user to a particular IP address, however its really messy and all the VM NIC's will slow down the terminal server. I'll setup a proof of concept Monday and let the group know how it affects performance.

  Read the article

• IIS6 site using integrated authentication (NTLM) fails when accessed with Win7 / IE8

  - by Ciove

  Hi, I'm having pretty similar problems as described in case 139099, but the fix there doesn't seem to work for me. Here's the details: Server: Win2003Srv R2 SP2 (stadalone, not a member of a domain). IIS6, TCP/443 (https). Anonymous access disabled. Integrated Windows authentication enabled. Local useraccouts Each useraccount has own virtual folder with change access and read access to site root. The 'adsutil NTAuthenticationProviders "NTLM"' -thing set to site root and useraccount's virtual folder. Client: Win7 Enterprise Member of a AD-Domain IE8 Allows three login attepts then fails. Using [webservername][username] in the logon window (Windows security) Logon using other browsers (Chrome and Firefox) works OK. The Web services log shows one 401.2 and two 401.1 events. The Security Event log shows two events, first is Fauilure Audit (680), The second event is Fauilure Audit (529) with these details: Logon Failure: Reason: Unknown user name or bad password User Name: [username] Domain: [webservername] Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: [MyWorkstation] Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: [999.999.999.999] Source Port: 20089 Any ideas appreciated.

  Read the article

< Previous Page | 706 707 708 709 710 711 712 713 714 715 716 717  | Next Page >