Search Results

Search found 55281 results on 2212 pages for 'get set'.

Page 712/2212 | < Previous Page | 708 709 710 711 712 713 714 715 716 717 718 719  | Next Page >

• Access to CD/DVD Drive is Denied through Windows 7 Explorer (Permission Problem)

  - by Synetech inc.

  A while ago I started having trouble with my optical drives. Both of them keep showing up in Explorer as CD/DVD drives on boot, but as soon as I put a disc in either one, it suddenly turns into a hard-drive—“local disk” is displayed in the Type column, though the File System column remains UDF/CDFS. (I though that maybe it was a permission issue on the registry key in HKLM\System\CurrentControlSet..., but I’m not so certain because of the next test.) When I try to open a disc (of any type), I get an access denied error message. If I open an elevated command-prompt, I am able to access the files. Also, if I kill Explorer and run it from an elevated command-prompt (thus giving Explorer elevated permissions), then I can access the files from Explorer. I’ve tried uninstalling and reinstalling the devices without success. The security dialog indicates that there are none set for the drives (no owner and no permissions). I tried setting the owner, but am only able to do so if there is a disc in it (it complains if it is empty), but the settings do not stick (if I immediately open the security dialog after setting it, it is empty again). I tried setting permissions, but that gives an error. I’ve included a screencap-flowchart of the security dialog of one of the drives below. (Yes, I made sure that there are no upper- or lower-filters, and yes, I ran sfc. I also made sure that in the policy editor, “devices: restrict CD-ROM...” is not set.) Does anyone know what the owner and permissions are supposed to be for optical drives and how to reset them?

  Read the article

• Setting up ssh config file with id_rsa through tunnel

  - by Rubens

  I've been struggling to set up a valid configuration to open a connection with a second machine, passing through another one, and using an id_rsa (which requests me a password) to connect to the third machine. I've asked this question in another forum, but I've received no answer that could be considered very helpful. The problem, better described, goes as follows: Local machine: user1@localhost Intermediary machine: user1@inter Remote target: user2@final I'm able to do the entire connection using pseudo-tty: ssh -t inter ssh user2@final (this will ask me the password for the id_rsa file I have in machine "inter") However, for speeding things up, I'd like to set my .ssh/config file, so that I can simply connect to machine "final" using: ssh final What I've got so far -- which does not work -- is, in my .ssh/config file: Host inter User user1 HostName inter.com IdentityFile ~/.ssh/id_rsa Host final User user2 HostName final.com IdentityFile ~/.ssh/id_rsa_2 ProxyCommand ssh inter nc %h %p The id_rsa file is used to connect to the middle machine (this requires me no password typing), and id_rsa_2 file is used to connect to machine "final" (this one requests a password). I've tried mixing up some LocalForward and/or RemoteForward fields, and putting the id_rsa files in both first and second machines, but I could not seem to succeed with no configuration whatsoever. Hope somebody can help me here! Regards! P.S.: the thread I've tried to get some help from: http://www.linuxquestions.org/questions/linux-general-1/proxycommand-on-ssh-config-file-4175433750/

  Read the article

• How to force the start and end date of a task in Microsoft Project to be on the same day?

  - by Hauke P.

  I have a task called "Interview person A about topic X". The task's duration is set to 2 hours. The start date of the task should automatically be calculated taking dependencies and resource availabilities into account. My question boils down to: How can I force this task to start and end on the same date? Background: In my case, Microsoft Project sets the start date to a Friday at 5pm. As my working hours are set to 8am to 12am and 1pm to 6pm (Mon-Fri), Microsoft Project "splits up" the task at 6pm on Friday and plans to continue it at 8am on the following Monday. However, it does not make any sense to stop the interview on a Friday and restart it on Monday. Therefore the automatic suggestion is not helpful in this case. That's why I'm looking for a way way to force the task to start and end on the very same day. (In my example, I'd like Microsoft Project to delay the start date of the task until Monday 8am as this is the first time slot in which the task "fits in completely".) By the way: I have lots of such cases... for that reason it would be really great if there was a solution that doesn't just deal with this single special case.

  Read the article

• How can I create a separate toolbar from the Task Bar?

  - by Iszi

  In Windows XP, you could separate toolbars from the Task Bar by dragging them to the desktop. They could then be left lying about anywhere on your screen or, my preferred option, docked to any side of the screen. I found this particularly useful to keep a handy list of common phone numbers quickly accessible. I'd create a new toolbar pointing to a custom folder, and put a bunch of dead shortcuts in the folder that had names and numbers as their file names. I'd then dock the toolbar to the left side, set it to auto-hide and always on top (options which could be set separate from the Task Bar as well) and it would be readily available no matter what else I was doing on my system. However, on my Windows 7 system, I seem unable to perform the crucial step of pulling the new toolbar off of the Task Bar. This is of course with the Task Bar "unlocked" so that I can move all my toolbars around. Is there something I'm missing here, or is this a feature that's been disabled in Windows 7? Is there any way to re-enable it, or otherwise achieve similar functionality? I'd rather be able to do this without additional software, if possible.

  Read the article

• Google Apps Domain Level Shared Contacts?

  - by dkirk

  My firm just switched to Google Apps Premiere addition 2 weeks ago and aside from the way Google handles shared contacts, things are going quite well. Previously, on our Exchange server we had numerous shared contact lists set up in the shared folders. We had a separate list for vendors, sales agents, etc.. Is there not a way to set up lists or groups such as this on the domain level in Google Apps? I have found a ton of forums with users asking the same question but no good answers unless you purchase some third party app in the marketplace. I have toyed around with the "google-shared-contacts-client" here: http://code.google.com/p/google-shared-contacts-client/ and this almost does it but it falls short when trying to group contacts on the domain level or when trying to search for a contact by company name. Are either of these things possible? I am now looking to create a Google Doc spreadsheet to share with the domain just to have a separated defined list of contacts that is search-able by various fields... Anyone who could shed some light on domain level contact sharing relating to the points above, I would be most grateful...

  Read the article

• Debian grub2 update removed Windows boot option.

  - by Wrikken

  Since I updated grub to grub 2 I no longer get the option to boot to Windows (which is unfortunately sometimes necessary for proprietary MSIE browser plugins I need to use for work). Relevant /boot/grub/menu.lst portion: ### END DEBIAN AUTOMAGIC KERNELS LIST # This is a divider, added to separate the menu items below from the Debian # ones. title Other operating systems: root # This entry automatically added by the Debian installer for a non-linux OS # on /dev/hda1 title Windows NT/2000/XP root (hd0,0) savedefault makeactive chainloader +1 This however does not appear anymore. I do have some entries in /boot/grub/grub.cfg with entries like these: menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os { insmod part_msdos insmod ext2 set root='(hd1,msdos1)' search --no-floppy --fs-uuid --set e638c434-4884-412f-a141-2c194f881fae echo 'Loading Linux 2.6.32-5-amd64 ...' linux /boot/vmlinuz-2.6.32-5-amd64 root=UUID=e638c434-4884-412f-a141-2c194f881fae ro quiet echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-5-amd64 } Do I have to alter that file? If so, what is the correct syntax for a Windows boot? If not, what could be the problem?

  Read the article

• How is the extra mSATA SSD disk used/configured in a Dell XPS laptop?

  - by Mark

  Some machines in the new XPS laptop range from Dell come with a regular, large (500GB+) HDD and an additional 32GB m-SATA SSD. The only detail I can find about this extra drive on the Dell site is this: Store your important files, multimedia and photos with XPS 15’s large hard drive options. To get instant access to your media, choose an optional mSATA solid-state drive (SSD) that can boot up to twice as fast as a regular hard drive and resumes in less than 1 second. I'd like to know more about how this extra drive is set up and used, specifically: Is anything installed on it (e.g. OS files or a boot loader) or is it just used as swap space? Is the m-SATA drive visible as a lettered drive in Windows? (I'd guess not if it's used for swap file only.) Is this unusual configuration likely to cause any problems later down the line - e.g. when upgrading to Windows 8? As usual, Dell's sales team haven't been able to help. If anyone's actually got a Dell machine with this or a similar hard drive set-up and can give a definitive answer rather than speculation I'll accept the answer.

  Read the article

• Apache Virtual Hosts behind Cisco Router

  - by Theo

  I'm setting up an Apache 2.2 Ubuntu web server for internal services that is also supposed to be accessed from outside our LAN. Our LAN has a single external IP that is the external IP of our RV042 Cisco router. We have set up several A records on our external DNS server that point to this IP. Our internal DNS server resolve the same records to the internal IP of our web server, so computers from inside the network can access them using the same address as if they were outside. We forwarded the router's external 80 port to our web server's 80 port. I have set up one Virtual Host for each domain name in our list, and my httpd.conf is something like this: ServerName web.domain.com NameVirtualHost *:80 <VirtualHost *:80> ServerName alfresco.domain.com <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass /alfresco http://localhost:8080/alfresco ProxyPassReverse /alfresco http://localhost:8080/alfresco ProxyPass /share http://localhost:8080/share ProxyPassReverse /share http://localhost:8080/share </VirtualHost> <VirtualHost *:80> ServerName crm.domain.com DocumentRoot /var/www/sugarcrm </VirtualHost> Now, this works if we are in our LAN. However, if we are outside of our LAN we reach our web server's default page saying: It Works! This is the default web page for this server. But we can't reach the virtual hosts, as if the domain name is not being preserved when the router forward the packets to the web server. Am I doing something wrong? How can I check what is going on? What should be the settings to make this work from outside?

  Read the article

• Vmware player change dhcp server settings

  - by Tathagata

  I have a Windows Server 2003 running from a Vmware player on Win 7 box. The idea is to test Windows Deployment service in the virtual network. Is it possible to configure the vmware dhcp server with WDS related stuff(option 66, 67)? I found a few references where people were using the vnetlib.exe to start, stop the dhcp serverchange the subnet mask etc - but there's no info on how to get set the dhcp server options. DHCP config from the virtual network editor I do have the Workstation, without the license for it. In the Virtual network Editor, the DHCP settings for the network I'm using, only allows me to set the subnetmask, IP ranges and stuff like that. But not the dhcp options. DHCP server on the WDS server Authorizing the DHCP server in the guest WDS server fails. The VMware player can run its own dhcp server fro the virtual network with out any authorization from the Active directory - can I do the same, with Win dhcp server in the guest Win Server? ~~~~~ Can I authorize W2K8 DHCP server for private network, even when prohibited in enterprise network? says we have to run a third party dhcp server... :/.

  Read the article

• HAProxy, health checking multiple servers with different host names

  - by Marco Bettiolo

  I need to load balance between multiple running servers with different host names. I cannot set-up the same virtual host on each one. Is it possible to have only one listen configuration with multiple server and make the Health Checks apply the http-send-name-header Host directive? I am using HAProxy 1.5. I came up with this working haproxy.cfg, as you can see, I had to set a different hostname for each health check as the health check ignores the http-send-name-header Host. I would have preferred to use variables or other methods and keep things more concise. global log 127.0.0.1 local0 notice maxconn 2000 user haproxy group haproxy defaults log global mode http option httplog option dontlognull retries 3 option redispatch timeout connect 5000 timeout client 10000 timeout server 10000 stats enable stats uri /haproxy?stats stats refresh 5s balance roundrobin option httpclose listen inbound :80 option httpchk HEAD / HTTP/1.1\r\n server instance1 127.0.0.101 check inter 3000 fall 1 rise 1 server instance2 127.0.0.102 check inter 3000 fall 1 rise 1 listen instance1 127.0.0.101:80 option forwardfor http-send-name-header Host option httpchk HEAD / HTTP/1.1\r\nHost:\ www.example.com server www.example.com www.example.com:80 check inter 5000 fall 3 rise 2 listen instance2 127.0.0.102:80 option forwardfor http-send-name-header Host option httpchk HEAD / HTTP/1.1\r\nHost:\ www.bing.com server www.bing.com www.bing.com:80 check inter 5000 fall 3 rise 2

  Read the article

• How can I automatically edit an email before auto-forwarding it?

  - by Miss Cellanie

  Is there a way to automatically edit emails before forwarding them? I'm getting email notifications from Foursquare that I want to send to my phone as text messages. I know how to send messages to my number using an email address (I'm in the US and use Verizon) but I don't know how to strip out any unnecessary formatting, like HTML, before the email gets sent. What I want: Ability to strip out HTML Ability to start forwarding at a specific part of the email based on a search (e.g., I might know that Foursquare starts their messages with "Hey hey!" and only want content after that phrase occurs) Ability to truncate at 160 characters Things I've tried: I'm not using Foursquare DM pings through Twitter because I have two Twitter accounts and Twitter only allows a phone to be linked to one account at a time. I'm not willing to change which account it's linked to. I tried to work around the Twitter limitation using Google Voice, but they don't support SMS short codes. I'll compromise on the features I want if I can find a free solution that doesn't require me to set up my own server. I do think this is computer related because it will happen on my computer, not on my phone. edit My current setup: Gmail in Firefox 3.0.15 on Windows XP. I use a netbook as my only personal computer. However, if the only way to accomplish this well is to set up my own mail server or something, I would still want to know that.

  Read the article

• What switch should we use for PCoIP?

  - by Jay R.

  We have a small lab space that seats 10 people and has 20 machines. Each machine is set to 1920x1200 resolution because the user apps are best used at that resolution. Currently the machines are all located close enough to montors that a DisplayPort cable will reach, but the pending lab remodel positions them around 80 feet or more away in racks. Our proposed solution is to use PCoIP. We purchased 10 PCoIP portals and 20 PCoIP host cards. We plan to set up a dedicated network to handle just the PCoIP traffic. After testing just one portal and one host card with a cheap 1G switch from a local office supply store, we were left with less than good impressions about the usefulness in our lab. The framerates were not spectacular and the mouse seemed jerky. Our concern is that we can't get away with the cheap 1G stuff from the store because adding more machines to the switch will just make the user experience worse. What switch would be recommended to best support our PCoIP situation? We will need to plug in at least 30 cables based on just those machines. Is there a particular feature to search for that makes a difference? Is there a switch that works best with PCoIP? Added Info: The reporting webapp for the host card shows maximum bandwidth usage to be 220000 kbps. The average appears to be around 180000 kbps. The reverse direction is much lower, like 15000 kbps.

  Read the article

• How to safely use grub rescue> in Fedora 16? System does not boot anymore

  - by YumYumYum

  When i boot my PC, i get this in my Fedora 16 distro. I have tried as following but none allowing me to boot anymore. Any help please? I am blocked completely. Grub loading. Welcome to GRUB! error: file not found. Entering rescue mode... grub rescue> grub rescue> ls (hd0) (hd0,gpt3) (hd0,gpt2) (hd0,gpt1) grub rescue> ls (hd0,gpt2)/ ./ ../ lost+found/ memtest86+-4.20 grub2/ System.map-3.1.0-0.rc3.git0.0.fc16.i686 config 3.1.0.0.rc3.git0.0.fc16.i686 grub/ vmlinuz-3.1.0.0.rc3.git0.0.fc16.i686 elf-memtest86+-4.20 initramfs-3.1.0.0.rc3.git0.0.fc16.i686.img initramfs-3.1.0.0.rc4.git0.0.fc16.i686.img System.mpa-3.1.0.0.rc3.git0.0.fc16.i686 config-3.1.0.0.rc3.git0.0.fc16.i686 vmlinuz-3.1.0.0.rc3.git0.0.fc16.i686 grub rescue> set prefix=(hd0,gpt2)/boot/grub grub rescue> set root=(hd0,gpt2) grub rescue>insmod normal error unknown filesystem. or sometimes "error: file not found." grub rescue>normal unknown command normal

  Read the article

• Sever 2008 R2 Powershell Script runs manually, but not as a scheduled task

  - by Aeisor

  I have a Powershell script that runs manually using the Powershell ISE; However, when run as a scheduled task using an administrator's credentials the task does not run with the expected results. The script: $request=new-object System.Net.WebClient $request.DownloadFile("...url...", "C:\path\to\file.csv") The administrator user has Full Control of both the script and the folder it is writing to. The url exists and responds in a reasonable time (<1s). If I run the task manually the status is 0x41301 ("Currently Running") until I eventually end it. I have set the task up using both of these methods: Start a Program: C:\path\to\PS.PS1 Start a Program: C:\windows\system32\WindowsPowerShell\v1.0\powershell.exe with additional options -noninteractive -command "C:\path\to\PS.PS1" Using option 1, the task history shows it has opened an instance of notepad.exe but never terminates it. Using option 2 it completes the task but doesn't download / create the file. I have used Set-ExecutionPolicy Unrestricted as this is not a signed script. Any ideas?

  Read the article

• How can I tell why I have access to a file share on Windows Server

  - by Joel

  I have a file share on a Windows 2008 R2 server in a AD domain (call it \SECURESERVER\STUFF) and I am not sure if I have the share and folder permissions set up right. I noticed the problem when I set up new server (WORKGROUP\FOREIGNSERVER) that was not joined to the domain and tried to copy some files off of \SECURESERVER\STUFF. I was surprised to find that when I tried to access the files, it did not prompt me for a username and password and proceeded to give me full access to the files. That worried me so I tried the same thing on some workstations that were not in the domain and they did NOT have the same behavior (they did prompt for a username/password as desired/expected). So, I think there is something peculiar about FOREIGNSERVER. I am logging into it with a local admin account, but my domain and SECURESERVER should know nothing of this server. I've carefully gone through the share and folder permissions on the share but I can't find the reason that FOREIGNSERVER has access. How can I find out why FOREIGNSERVER has access to SECURESERVER?

  Read the article

• Trying to communicate between virtual servers on the same host through ipv6

  - by Daniele Testa

  I am running KVM on a host with 2 virtual servers. Each virtual server has a own bridge interface on the host VPS1 has br1 VPS2 has br2 Each virtual server has a own ipv4 and a ipv6. The virtual servers has no problem communicating with internet or with eachother through ipv4. However, with ipv6, they can only communicate with internet and NOT with eachother. The host can ping the 2 virtual servers without any problems, but they cannot ping eachother. iptables has been set to ACCEPT on all chains, so it is not the problem. VPS1 has ipv6 = 2a01:4f8:xxx:xxx::10 VPS2 has ipv6 = 2a01:4f8:xxx:xxx::5 the host has the following routes set: ip route add 2a01:4f8:xxx:xxx::10 dev br1 ip route add 2a01:4f8:xxx:xxx::5 dev br2 When I do a ping from VPS2 to VPS1, I see the following on the host: tcpdump -i br1 15:32:27.704404 IP6 2a01:4f8:xxx:xxx::10 > ff02::1:ff00:5: ICMP6, neighbor solicitation, who has 2a01:4f8:xxx:xxx::5, length 32 So it seems like the host is seeing the request coming from VPS1 on br1. But for some reason, it does not forward it to br2. Instead it is asking where the destination IP is through ipv6 multicast. Anyone has a clue what is going on? I find this very strange, as it is working fine with ipv4 with the exact same settings and routes.

  Read the article

• allow spoofing when using tun

  - by Johnny

  I have a working openvpn setup with a server and a number of clients. How would i go around allowing IP spoofing through the openvpn server? (to demonstrate security concepts)? A normal ping from client to server goes through all right: root@client: hping3 10.8.0.1 HPING 10.8.0.1 (tun0 10.8.0.1): NO FLAGS are set, 40 headers + 0 data bytes len=40 ip=10.8.0.1 ttl=64 DF id=0 sport=0 flags=RA seq=0 win=0 rtt=124.7 ms root@server:/etc/openvpn# tcpdump -n -i tun0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tun0, link-type RAW (Raw IP), capture size 65535 bytes 10:17:51.734167 IP 10.8.0.6.2146 > 10.8.0.1.0: Flags [], win 512, length 0 But when spoofing a packet, it does not arrive at the openvpn server: root@client: hping3 -a 10.0.8.120 10.8.0.1 HPING 10.8.0.1 (tun0 10.8.0.1): NO FLAGS are set, 40 headers + 0 data bytes root@server:/etc/openvpn# tcpdump -n -i tun0 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on tun0, link-type RAW (Raw IP), capture size 65535 bytes My current config files server.conf local X.Y.Z.P port 80 proto tcp dev tun ca ca.crt cert server.crt key server.key # This file should be kept secret dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1 bypass-dhcp" keepalive 10 120 comp-lzo persist-key persist-tun persist-local-ip status openvpn-status.log verb 3 client.conf client dev tun proto tcp remote MYHOST..amazonaws.com 80 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3

  Read the article

• How to use LVM on Rackspace Cloud

  - by batrick

  Dear all, I am trying to set up a simple but effective solution to make a backup of my rackspace cloud servers. These servers each run subversion, trac, and some database-backed custom php applications. My idea is to set up a LVM and mount a volume under, say, /srv. In this volume, I keep the data from all applications. Instead of caring about how to back-up each app in a different way (svn hotcopy, trac-admin hotcopy, huge mess for mysql), I simply take an LVM snapshot and back this one up cloud files using the excellent cloudcity script (http://github.com/jspringman/cloudcity/blob/master/cloudcity). The advantage of this solution is that it is quick and easy, and LVM allows to make decent backups. As more apps are added, it should not be required to change the backup script much. The downside, and main point of my question here, is that I am not sure how to get LVM working on Rackspace cloud, because there is only one root volume and no service like Amazon's EBS. I was thinking it may be possible to create a large empty file and use this as a "physical volume". Has anybody done anything like this before? Or do you know why it can never work? It would be great to hear from you. Thanks, batrick

  Read the article

• Cloning a git repository from a machine running OS X

  - by Mike

  Hi folks, I'm trying to host a git repository from my home OS X machine, and I'm stuck on the last step of cloning the repository from a remote system. Here's what I've done so far: On the OS X (10.6.6) machine (heretofore dubbed the "server") I created a new admin user Logged into the new user's account Installed git Created an empty git repository via "git init" Turned on remote login Set port mapping on my router (airport extreme) to send ssh traffic to the server Added a ".ssh" directory to the user's home directory From the remote machine (also an OS X 10.6.6 machine), I sent that machine's public key to the server using scp and the login credentials of the user created in step 1 To test that the server would use the remote machine's public key, I ssh'd to the server using the username of the user created in step 1 and indeed was able to connect successfully without being asked for a password I installed git on the remote machine From the remote machine I attempted to "git clone ssh://[email protected]:myrepo" (where "user", "my.server.address", and "myrepo" are all replaced by the actual username, server address and repo folder name, respectively) However, every time I try the command in step 11, I get asked to confirm the server's RSA fingerprint, then I'm asked for a password, but the password for the user I set up for that machine never works. Any advice on how to make this work would be greatly appreciated!

  Read the article

• Why are SIP calls via my server silent?

  - by Archcode

  I have FreeSWITCH SIP server up and running. It has public IP and sits behind 1-to-1 NAT (it's Amazon EC2 instance actually). I can connect to it, make a call to other endpoint (namely, my android device to my pc and vice versa) and signals are send with no problems (call, answer, hangup, etc). Unfortunately, and what drives me crazy, that's all: no audio gets through, no video either. Server does not throw errors, it reports many retransmission though, looks like this: switch_rtp.c:915 [ zrtp engine]: WARNING! HELLO Max retransmissions count reached (20 retries). ID=15 Codecs are set up correctly (same config worked locally on my LAN). NAT/firewall on client side may be a problem, signals do get through (perhaps due to fixed port, data streaming runs on random one, that is currently my best bet). STUN/TURN/ICE setting on client seem to have no effect. Endpoints sit behind symmetric NAT. On server there are no iptables rules, security group is set as suggested there: http://wiki.freeswitch.org/wiki/Firewall Help, please. How to make it work or at least diagnose what's wrong?

  Read the article

• Coloring of collapsed threads in mutt

  - by Rich

  I'm trying to figure out the syntax of colouring collapsed threads in the mutt index. The documentation for mutt patterns doesn't seem to include a description of how this works, and so far I've been completely unable to figure it out by trial and error. What I'd like is for collapsed threads that contain any unread (new) messages to be always coloured green. If collapsed threads with no unread messages contain any flagged messages, then I'd like them to be red. So far, every set of patterns I've tried results in threads that contain both flagged and unread messages being coloured red (I want them green). These work: color index green default "~N" # unread messages color index green default "~N~F" # unread flagged messages color index red default "~F" # flagged messages color index green default "~v~(~N)" # collapsed thread with unread But these don't: color index green default "~v~(~N~F)" # attempt to keep threads with unread green color index red default "~v~(~F)" # colours collapsed threads with flagged and unread red color index red default "~v~(!~N~F)" # ditto color index red default "~v~(^!~N~F)" # ditto color index red default "~v~(~F)~(!~N)" # ditto color index red default "~v~(~F)~v~(!~N)" # ditto I've also tried switching the order of the "~v~(~F)" and "~v~(~N)" commands in the file, but the "flagged" rule always seems to take precedence over the "new" rule. Ideally I'd like to understand how the syntax for colouring collapsed threads works, but at this point I'd happily settle for a set of rules that achieves the colourscheme described above.

  Read the article

• server_name seems to be ignored in nginx

  - by user46171

  I have two domains set up in nginx.conf. Both are using SSL with their own certificates, and proxy to Apache. However the second domain is completely ignored, and nginx always resolves to the first domain. I can't see what in the issue is with this configuration, having set the server_name in each case correctly (as far as I can see): http { include mime.types; default_type application/octet-stream; keepalive_timeout 65; upstream site { # real IP addresses masked server xx.xxx.x.xxx; server xx.xxx.x.xxx; } server { # this domain always works listen 443; server_name *.first-site.com; ssl on; ssl_certificate /var/ssl/first-site.crt; ssl_certificate_key /var/ssl/first-site.key; location / { access_log off; proxy_connect_timeout 15; proxy_next_upstream error; proxy_pass http://site; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Protocol https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } server { # this domain is ignored, always resolves to first-site.com listen 443; server_name *.second-site.com; ssl on; ssl_certificate /var/ssl/second-site.crt; ssl_certificate_key /var/ssl/second-site.key; location / { access_log off; proxy_connect_timeout 15; proxy_next_upstream error; proxy_pass http://site; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Protocol https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } }

  Read the article

• LighTPD and PHP not working if outside of LightTPD folder

  - by Marco83

  I need to set up a simple web server with PHP on Windows XP that a number of different people will use for local testing. I'm using LightTPD 1.4.30-4-IPv6-Win32-SSL and PHP 5.2. So far I've created this folder structure: tools/ LightTPD/ htdocs/ PHP/ I set up PHP as CGI and the document root as server_root + "/htdocs". It works fine (well, it's slow but I don't want to bother with FastCGI for now :) ). My problem is when I try to put the htdocs outside of LightTPD folder, like this: htdocs/ tools/ LightTPD/ PHP/ I update the document root to server_root + "/../../htdocs" and while static HTML pages work fine, PHP pages stop working (they return a "No input file specified"). I literally just change the document root, I didn't change anything in the php.ini or anywhere else. Please also note that I left all doc_root, user_dir and cgi.force_redirect to the default values in php.ini, and it works when htdocs is inside LightTPD, but not when I move it ouside. Any idea of why it's breaking?? Here's my lightTPD.conf: server.modules = ( "mod_access", "mod_accesslog", "mod_alias", "mod_cgi", "mod_status", ) include "variables.conf" include "mimetype.conf" # THIS WORKS server.document-root = server_root + "/htdocs" # THIS DOESN'T #server.document-root = server_root + "/../../htdocs" server.upload-dirs = ( temp_dir ) index-file.names = ( "index.php", "index.pl", "index.cgi", "index.cml", "index.html", "index.htm", "default.htm" ) server.event-handler = "libev" url.access-deny = ( "~", ".inc" ) $HTTP["url"] =~ "\.pdf$" { server.range-requests = "disable" } static-file.exclude-extensions = ( ".php", ".pl", ".cgi" ) server.errorlog = server_root + "/logs/error.log" ######### Options that are good to be but not neccesary to be changed ####### dir-listing.activate = "enable" #### CGI module cgi.assign = ( ".php" => server_root + "/../PHP/php-cgi.exe" ) status.status-url = "/server-status" status.config-url = "/server-config"

  Read the article

• Windows 7 mouse multi selection on windows explorer with CTRL and point to select / single click to open

  - by bortao

  This is something that have annoyed me since i changed to Windows 7. I don't do double click for a long time now since windows introduced 1 click selection (Folder Options Click items as follows Single click to open an item). The problem is, when i click Control and hover over the items, they select/deselect automatically every small amount of mouse movement i make. What i want is to select/deselect the items only when i enter/exit them. So to deselect an item im hovering, i have to move the mouse out of it, and then back in. I'm using Intellimouse Explorer official drivers. (edit) Here's another related annoyance: When you are hovering something and move the mouse inside other item (Holding Ctrl) The new item may or may not be selected. If you continue moving the mouse it gets selected/deselected as you move. (more edit) I have found that the parameter HKCU\Control Panel\Mouse\MouseHoverHeight / MouseHoverWidth have some influence here. If it's set to 2, the item select/deselect really quickly as you move the mouse. When set to larger numbers, its slower. But setting to 20 or 200 don't seem to be much different.

  Read the article

• Is the Windows VPN secure?

  - by Tor Haugen

  I have used a few VPN solutions over the years. Most are hard to set up, slow to connect and/or rather ill-behaved (replacing system drivers, disrupting each other etc). One solution I have never used earlier is the one built into Windows. This is mostly because the infrastructure guys always refuse to use it because they claim it's 'not secure'. Now I have finally had the chance to use it (on Windows 7), and wow, it's a breeze! Easy to set up, well-behaved, it connects almost instantly, automatically authenticates with my logged-in credentials, and integrates excellently with the UI. I have to say, unless it really isn't secure, I'll be happy if I never have to use another VPN product ever again. I gather the Windows VPN used to rely on PPTP, which is not considered secure. But in Windows 7/2008, it supports L2TP/IPSec, SSTP and IKEv2, and authenticates with EAP or CHAP/CHAPv2. That seems pretty up-to-date to me. But I'm just a lowly developer. Can someone in the know give me the lowdown on this?

  Read the article

< Previous Page | 708 709 710 711 712 713 714 715 716 717 718 719  | Next Page >