sudden shutdown - Page 72

iSCSI, failover and XenServer

- by jemmille

I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid> is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

Read the article

Issues with doing a P2V on Exchange 2007

- by PokermUNKEE

I shutdown all Exchange services on the physical box and did a convert. Everything converted fine. Server booted up no issues and I could receive email from the outside world with no issues. But I am unable to send emails internally or externally. They just sit in the Outbox. I also disabled the DHCPClient service as I didn't want the server to get an IP address from DHCP when it first came online. It came online with no IP, then I used console to assign the correct static IP address (same one on the physical server) and rebooted. I ran the Exchange Troubleshooting Agent and it gave me the following errors: The value for the '\MSExchangeIS Mailbox\Messages Queued For Submission' counter on server exchange is greater than zero (average value is 8.8) and it appears that 'MSExchangeMailSubmission' is failing to submit messages to at least one computer with the Hub Transport server role installed over the last minute. Found 1 computers with the Hub Transport server role installed in the same Active Directory site as server exchange using local Active Directory site GUID 'ce8a4367-1bf6-4825-9cac-c4e2b115c450'. Check Local Active Directory Site Hub Transport Server Role Health (Mailflow_CheckLocalBhHealth1.1.1.1.1.1.1.1) I have one Exchange server with all the roles on it. Has anyone see this before when doing a convert? Please help :(

Read the article

Sending USR2 to mongrel_rails sometimes results in an “Address already in use” on the restart

- by Ben

We have a rolling-restart mode for our mongrel cluster that sends a USR2 signal to each running process. This works great, most of the time. But very occasionally the mongrel process will shutdown, and then fail to restart, with the following error: /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/tcphack.rb:12:in `initialize_without_backlog': Address already in use - bind(2) (Errno::EADDRINUSE) from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/tcphack.rb:12:in `initialize' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel.rb:93:in `new' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel.rb:93:in `initialize' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/configurator.rb:139:in `new' from /usr/local/lib/ruby/gems/1.8/gems/mongrel-1.1.5/bin/../lib/mongrel/configurator.rb:139:in `listener' Looking though the mongrel source, the USR2 handler calls a synchronous stop on the running server, so it ought to block until the socket has been released. Has anyone seen this error? Does anyone have any ideas what might cause it? (I asked this question over on StackOverflow initially, but thought it might be more appropriate here)

Read the article

How can I resolve Oracle 11g XE connection failure straight after installation?

- by d3vid

I have just installed Oracle 11g XE on a Windows 7 VirtualBox VM, using all the default options. "Getting Started" fails When I click on Getting Started I get taken to http://127.0.0.1:8080/apex/f?p=4950 which fails. After some browsing I came across a suggestion to confirm the HTTP port, but I can't get this far, because I can't connect. connect system fails If I select Run SQL command line I get taken to a SQL prompt. I enter connect system and get prompted for a password. I enter the password. I immediately get the following error: ERROR: ORA-01033: ORACLE initialization or shutdown in progress Process ID: 0 Session ID: 0 Serial number: 0 Info: Start database This happens whether or not I run Start database first. (Start database just opens a Windows command prompt window.) Info: Windows services My Oracle services start as follows: Starting the manual services doesn't resolve the problem. Enabling and starting the disabled service doesn't resolve the problem. Is there something I haven't done? How can I resolve this connection error?

Read the article

Mysql Algorithm for Determining Closest Colour Match

- by buggedcom

I'm attempting to create a true mosaic application. At the moment I have one mosaic image, ie the one the mosaic is based on and about 4000 images from my iPhoto library that act as the image library. I have already done my research and analysed the mosaic image. I've converted it into 64x64 slices each of 8 pixels. I've calculated the average colour for each slice and assertain the r, g, b and brightness (Luminance (perceived option 1) = (0.299*R + 0.587*G + 0.114*B)) value. I have done the same for each of the image library photos. The mosaic slices table looks like so. slice_id, slice_image_id, slice_slice_id, slice_image_column, slice_image_row, slice_colour_hex, slice_rgb_red, slice_rgb_blue, slice_rgb_green, slice_rgb_brightness The image library table looks like so. upload_id, upload_file, upload_colour_hex, upload_rgb_red, upload_rgb_green, upload_rgb_blue, upload_rgb_brightness So basically I'm reading the image slices from the slices table into PHP and then pulling out the appropriate images from the library table based on the colour hexs. My trouble is that I've been on this too long and probably had too many energy drinks so am not concentrating properly, I can't figure out the way to pick out the nearest colour neighbor if the appropriate hex code doesn't exist. Any ideas on the perfect query? NB: I know pulling out the slices one by one is not ideal however the mosaic is only rebuilt periodically so a sudden burst in the mysql load doesn't really bother me, however if there us a way to pull the images out all at once that would also be a massive bonus.

Read the article

Vagrant ssh fails with VirtualBox

- by lukewm

vagrant up fails when it gets to the ssh part: myterminal$ vagrant up [default] VM already created. Booting if its not already running... [default] Running any VM customizations... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- ssh: 22 => 2222 (adapter 1) [default] -- db2: 30003 => 30003 (adapter 1) [default] Cleaning previously set shared folders... [default] Creating shared folders metadata... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] Failed to connect to VM! Failed to connect to VM via SSH. Please verify the VM successfully booted by looking at the VirtualBox GUI. Then when I subsequently try and connect using vagrant ssh or vagrant reload or similar, I get this: myterminal$ vagrant reload [default] Attempting graceful shutdown of linux... SSH connection was refused! This usually happens if the VM failed to boot properly. Some steps to try to fix this: First, try reloading your VM with `vagrant reload`, since a simple restart sometimes fixes things. If that doesn't work, destroy your VM and recreate it with a `vagrant destroy` followed by a `vagrant up`. If that doesn't work, contact a Vagrant maintainer (support channels listed on the website) for more assistance. Please help! I'm really stumped. Kind regards, Luke

Read the article

Auto load balancing two node Cluster Hyper-v 2008 R2 enterprise?

- by Kristofer O

My setup is a 2 node cluster with 72GB ram each and a ~10TB MD3000i Iscsi SAN. I have about 30VMs running I keep about 15 on either server. I do a live migration to the other server if I need to run updates or whatever... Either one of the servers is able of running all VM if needed, but the cpu is pretty high. Here's my issues. I know Hyper-v has a limit of a single Live-migration at a time. But Why doesn't it queue them up to move one at a time? If I multi select I don't get the option to live migrate a one at a time. OR if I'm in the process of Migrating one it will give me an error that it's currently migrating a VM... Is there a button I missed that will tell a Node that it needs to migrate all the VMs elsewhere? Another question, does anyone know whats the best way to load balance VMs based on CPU and/or network utilzation. I have some VMs that don't do much. and some that trash the CPU or network. I'd like to balance it out on both servers if at all possible. and Is there any way to automate it? last question... If I overcommit my Cluster is there a way to tell the cluster that I want certian VMs the be running and to savestate other VMs based on availible system resources? Say when my one node blue screens and the other node begins starting the VMs up. I want the unimportant ones to shutdown or savestate so the important ones can stay running or come back online. Thanks just for reading all that. Any help would be great.

Read the article

Ubuntu 10.04 (Lucid) OpenLDAP invalid credentials issue

- by gmuller

This won't be a question, but a solution to an infuriating problem on Ubuntu 10.04. If you tried to deploy an LDAP server using this distro following the tutorials below, you'll be on serious trouble. Tutorials: https://help.ubuntu.com/9.10/serverguide/C/openldap-server.html https://help.ubuntu.com/9.10/serverguide/C/samba-ldap.html The error first appear, on the line: "ldapsearch -xLLL -b cn=config -D cn=admin,cn=config -W olcDatabase=hdb olcAccess" It simply won't allow admin to access the "cn=config", thus you won't be able to deploy the LDAP server correctly. After almost a week searching for a solution, I've found this page: https://bugs.launchpad.net/ubuntu-docs/+bug/333733 On comment #5, the solution is presented. Quoting the author: when you get to the setting up ACL part you all of a sudden need to use a cn=admin,cn=config, that doesn't exist creating a config.ldif with dn: olcDatabase={0}config,cn=config changetype: modify add: olcRootDN olcRootDN: cn=admin,cn=config dn: olcDatabase={0}config,cn=config changetype: modify add: olcRootPW olcRootPW: secret dn: olcDatabase={0}config,cn=config changetype: modify delete: olcAccess and adding it with ldapadd -Y EXTERNAL -H ldapi:/// -f config.ldif It's unacceptable that a Linux distribution, popular like Ubuntu, have such ridiculous bug. Hope it helps everyone!

Read the article

kvm works only when kvm-intel is unloaded

- by Sathya

I am new to kvm. I have this strange issue. But before explaining the issue, here is my set up. I try to install VM on my Host which is a Acer Laptop 5720 Has T7500 Intel processor. The cpu flags indicate that Virtualization is supported. I run Ubuntu 10.04 (lucid) on it. It comes with kvm. Now coming to the issue - I dont get any errors while executing "sudo modprobe kvm-intel". So I presume my processor does indeed support hardware virtualization. I use virt-manager and create a VM on which I install ubuntu from an *.iso file. When I start the VM it says it is running. No signs of any trouble. I can see the domain list in "virsh list". But when I try to connect to the VM thru VNC, all I get to see is a blank screen (no cursor). There is no response to any key press. I changed the video mode etc. Tried all different combinations but none work. But strangely, if I shutdown the vm an virt-manager and then unload the module by doing "sudo modprove -r kvm-intel", everything works fine. ie., I can see the screen via VNC. I am able to install the OS and so on. So what does this mean ? IS hardware virtualization not supported ? How come there is no error anywhere ? dmesg | grep kvm doesnt report anything. Can someone throw light on what excatly is happening ?

Read the article

Handling 2 buttons submit Actions in a single View/Form - ASP.NET MVC 2 RTM

- by Leniel Macaferi

I have a View in which the user is able to upload a file to the server. In this view I also have 2 buttons: one to Upload a file and other to Download the last file imported. In my Controller I created 2 action methods: Import and Export. How could I manage to redirect each button click to the proper action method in my Controller? I have tried Html.ActionLink: <%= Html.ActionLink("Upload", "Import", "OracleFile")%> <%= Html.ActionLink("Download", "Export", "OracleFile")%> Html.ActionLink didn't do the trick. The action links were taking me to the right Action methods but they were generating a GET request. This way Request.Files.Count = 0. I need a POST request. Note: the most intriguing part is that the upload was working and all of sudden it stopped working. I've seen that some people are having the same problem with FileUpload tasks in which the Request.Files is always Empty. I think it's empty because you need a post to the server. Isn't it?

Read the article

MDA BindingFailure detected

- by Vnuk

WebForms web site upon first launch from VS2008 throws this exception on my dev machine, after clicking continue everything works. Also, everything works on server when deployed. What is this VJSharpCodeProvider, why is it being loaded in vb.net project and why did it start happening all of a sudden? The assembly with display name 'VJSharpCodeProvider' failed to load in the 'LoadFrom' binding context of the AppDomain with ID 2. The cause of the failure was: System.IO.FileNotFoundException: Could not load file or assembly 'VJSharpCodeProvider, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' or one of its dependencies. The system cannot find the file specified. File name: 'VJSharpCodeProvider, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' === Pre-bind state information === LOG: User = quad7\devuser LOG: DisplayName = VJSharpCodeProvider, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a (Fully-specified) LOG: Appbase = file:///C:/dev/ins/ LOG: Initial PrivatePath = C:\dev\ins\bin Calling assembly : (Unknown). === LOG: This bind starts in default load context. LOG: Using application configuration file: C:\dev\ins\web.config LOG: Using machine configuration file from C:\Windows\Microsoft.NET\Framework\v2.0.50727\config\machine.config. LOG: Post-policy reference: VJSharpCodeProvider, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a LOG: Attempting download of new URL file:///C:/Windows/Microsoft.NET/Framework/v2.0.50727/Temporary ASP.NET Files/root/f645d80b/bb4d1cdf/VJSharpCodeProvider.DLL. LOG: Attempting download of new URL file:///C:/Windows/Microsoft.NET/Framework/v2.0.50727/Temporary ASP.NET Files/root/f645d80b/bb4d1cdf/VJSharpCodeProvider/VJSharpCodeProvider.DLL. LOG: Attempting download of new URL file:///C:/dev/ins/bin/VJSharpCodeProvider.DLL. LOG: Attempting download of new URL file:///C:/dev/ins/fakturaTest/bin/VJSharpCodeProvider/VJSharpCodeProvider.DLL. LOG: Attempting download of new URL file:///C:/Windows/Microsoft.NET/Framework/v2.0.50727/Temporary ASP.NET Files/root/f645d80b/bb4d1cdf/VJSharpCodeProvider.EXE. LOG: Attempting download of new URL file:///C:/Windows/Microsoft.NET/Framework/v2.0.50727/Temporary ASP.NET Files/root/f645d80b/bb4d1cdf/VJSharpCodeProvider/VJSharpCodeProvider.EXE. LOG: Attempting download of new URL file:///C:/dev/ins/bin/VJSharpCodeProvider.EXE. LOG: Attempting download of new URL file:///C:/dev/ins/bin/VJSharpCodeProvider/VJSharpCodeProvider.EXE.

Read the article

How to configure Hyper-V failover cluster to live migrate when dynamic memory runs out?

- by Matt Johnson

Appologies in advance that this is not a direct programming question, but I have a feeling that the solution involves custom powershell scripts (maybe), so this is as good a place to ask as any. I maintain a website that has a large Hyper-V cluster for SQL Servers. We are using Windows 2008 R2 SP1, and the new "dynamic memory" feature. I've already ready reviewed the Best Practices Guide, and implemented it's suggested configuration. Everything works well, except that when SQL demand increases memory pressure to expand to more memory than is available on the physical machine, the memory status goes into the "Warning" state and stays there. I assume the hypervisor is using a swapfile on the host to fulfill the memory requirement, thus slowing the virtual machine down. When this happens, there are plenty of other nodes in the cluster that have available resources. I can live-migrate the virtual server over there and everything works, and the warnings go away. Now how can I automate this? I see no menu options in either Hyper-V or the Failover Cluster Manager for performing a migration or shutdown when dynamic memory goes into the warning state. Any ideas about how to script this, or monitor it and invoke the action directly, would be helpful. If the solution involves coding, powershell would be ideal, but I could envison this as a .Net Service that monitors for this state and kicks off the migration request. I just don't know what objects are involved in doing the monitoring or kicking off the live migration. Thanks in advance.

Read the article

MySQL socket connections working, but not port connections

- by Neil

I installed MySQL community 5.1.45 on my Snow Leopard 10.6, using the pkg from their site. I had previously installed a MySQL binary from entropy.ch. In the previous installation, the connections were working fine before I upgrade to Snow Leopard. In Snow Leopard, both the installations are problematic. Using an app called Sequel Pro, if I connect with the socket operation, it connects properly. However, a standard connection with the same credentials doesn't work. From what I've understood, socket connections happen on the machine itself between processes, whereas normal connections occur over the network/ports, in this case a loopback to my machine, since the server and client are both on the same machine. My new CakePHP installation isn't being able to connect to the db with the root credentials I provided. Btw, I've been starting the MySQL server using the Preference Pane. When I tried running mysqld from terminal, it gave me: 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test mysqld: Can't change dir to '/usr/local/mysql-5.1.45-osx10.6-x86_64/data/' (Errcode: 13) 100323 1:54:37 [ERROR] Aborting 100323 1:54:37 [Note] mysqld: Shutdown complete mbp is the name of my machine. How do I fix this so that my webserver can connect to the mysql server?

Read the article

Experience with AMCC 3ware 9650se raid cards? Ours seems dead

- by antiduh

We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

Read the article

SQL Server instance shuts down

- by user42119

I'm currently developing a new ASP.NET project hosted on a Windows Server 2008 RC2 with an SQL Server 2008 Express database. I have three SQL Server instances (for different purposes) running which currently all contain a single database. For apparently no reason, these instances tend to shut down after some days. There might be low or no traffic to these instances, because there might be some days in a row, where I can't develop. It now occurred several times, that one or two of these three instances just shut down, so that I can't access the database, without manually starting the instance. I can't seem to find a event log entry for the shutdown, which is most likely because I just enabled logging (why is the default setting off?). So the questions are: * Why does an SQL Server instance shut down? (Is there such a thing as a "Shut down instance after 3 days of inactivity"? * How can I achieve that the instances are running 24/7? Edit: I solved this problem by writing my own application that checks for the status of the SQL Server services. My program will start via a batch file, that gets called by the Windows Task Scheduler every 5 minutes.

Read the article

During suite tests EasyMock says 0 matchers expected 1 recorded

- by holmes

So I've been using EasyMock's class extension for a while now. All of a sudden I'm getting this exception, but only when I run the entire test suite: java.lang.IllegalStateException: 0 matchers expected, 1 recorded. at org.easymock.internal.ExpectedInvocation.createMissingMatchers(ExpectedInvocation.java:42) at org.easymock.internal.ExpectedInvocation.<init>(ExpectedInvocation.java:34) at org.easymock.internal.ExpectedInvocation.<init>(ExpectedInvocation.java:26) at org.easymock.internal.RecordState.invoke(RecordState.java:64) at org.easymock.internal.MockInvocationHandler.invoke(MockInvocationHandler.java:24) at org.easymock.internal.ObjectMethodsFilter.invoke(ObjectMethodsFilter.java:56) at org.easymock.classextension.internal.ClassProxyFactory$1.intercept(ClassProxyFactory.java:74) at com.protrade.soccersim.data.emulator.matrix.PositionCategoryMatrix$$EnhancerByCGLIB$$c5298a7.getPossession(<generated>) at com.protrade.soccersim.data.emulator.stats.team.PossessionCalculatorUnitTest.testDeterminePossessionHomeWin(PossessionCalculatorUnitTest.java:45) The code involved is this little beauty (trimmed a bit): @Before public void setUp() throws Exception { homeTeam = createMock( PositionCategoryMatrix.class ); awayTeam = createMock( PositionCategoryMatrix.class ); ... } @Test public void testDeterminePossessionHomeWin() { expect(homeTeam.getPossession()).andReturn( 0.15151515 ); expect(awayTeam.getPossession()).andReturn( 0.01515152 ); replay( homeTeam, awayTeam ); ... } The exception is being thrown on the first expect. And it really doesn't make sense. It says it's getting a matcher, but the method doesn't even take an argument. And odd enough it's only during test suites! I'm creating a new mock in the @Before, so it shouldn't be inheriting anything from somewhere else (not that some other method would have a matcher on it) So, any ideas?

Read the article

Accidently overwrote system.dbf - What now?

- by Filip Ekberg

I accidentally overwrote system.dbf in /usr/lib/oracle/xe/oradata/XE/system.dbf Well I did not actually do it accidentally, however I overwrote it because of other failures in the database. And when I try running the following: SQL> shutdown ORA-01109: database not open Database dismounted. ORACLE instance shut down. SQL> startup ORACLE instance started. Total System Global Area 289406976 bytes Fixed Size 1258488 bytes Variable Size 92277768 bytes Database Buffers 192937984 bytes Redo Buffers 2932736 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open Now I want to try to Recover the database because starting it in mounted or standard surely doesn't work. SQL> recover database using backup controlfile; ORA-00283: recovery session canceled due to errors ORA-01110: data file 1: '/usr/lib/oracle/xe/oradata/XE/system.dbf' ORA-01122: database file 1 failed verification check ORA-01110: data file 1: '/usr/lib/oracle/xe/oradata/XE/system.dbf' ORA-01206: file is not part of this database - wrong database id How do I solve this? Is it even possible? My "real" problem was that I ran the /etc/init.d/oracle-xe configure and it overwrote my old configuration and probably removed passwords and such so my tables were gone, however I found the mytablespace.dbf so I hope that it is possible to recover? Please shed some light on this.

Read the article

port forwarding with VirtualBox

- by Argh

I have a virtualbox VM running ubuntu. The Ubuntu guest is running a web server which listens on port 3000 (http://127.0.0.1:3000) The host machine is windows vista. I have configured port forwarding using VBoxManage. If I query the config using VboxManage getextradata "MyMachine", I get Key: GUI/AutoresizeGuest, Value: on Key: GUI/Fullscreen, Value: off Key: GUI/LastCloseAction, Value: shutdown Key: GUI/LastWindowPostion, Value: 9,34,640,529,max Key: GUI/MiniToolBarAlignment, Value: bottom Key: GUI/MiniToolBarAutoHide, Value: off Key: GUI/SaveMountedAtRuntime, Value: yes Key: GUI/Seamless, Value: off Key: GUI/ShowMiniToolBar, Value: yes Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/GuestPort, Value: 3000 Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/HostPort, Value: 3000 Key: VBoxInternal/Devices/pcnet/0/LUN#0/Config/guesthttp/Protocol, Value: TCP This looks like it should work... However when I try to access the web server from the host machine (windows box) I dont get a response. I ran a netstat on the windows box and nothing appears to be listening on port 3000 which explains why forwrding isnt working. Note that I have already tested with my firewall switched off... The version of VirtualBox I am using is 3.1.4 Any ideas?

Read the article

What DBus signal is sent on system suspend?

- by Paul Robinson

Hello, I need to detect when a machine is going to sleep in Ubuntu 9.10 and Fedora 13. Both use UPower, so I've been looking on the "org.freedesktop.UPower" DBus bus for such signals. I've been listening for the "sleeping" signal on the UPower bus with the following command: dbus-monitor --system "type='signal',interface='org.freedesktop.UPower',member='Sleeping'" When I sleep the machine (either by closing the lid, selecting "shutdown - suspend" or sending a DBus message) I don't see a "sleeping" event. I notice that the "Sleeping" event is sent when the "org.freedesktop.UPower.AboutToSleep" method is invoked. I can do this manually by calling: dbus-send --print-reply --system --dest=org.freedesktop.UPower /org/freedesktop/UPower org.freedesktop.UPower.AboutToSleep And I notice the "sleeping" signal is fired. My understanding is that anything that sleeps the PC must send the "AboutToSleep" signal before hand. It doesn't seem like this is happening. I've tried these steps on both Fedora 13 and Ubuntu 9.10 and I see the same results. Can anyone explain what's happening or provide me with an alternative DBus signal to listen for? Many thanks, Paul

Read the article

Amazon EC2 RSA key stopped authenticating - Permission denied (publickey)

- by shedd

Authenticating to our Ubuntu EC2 instance worked fine until a little while ago. All of a sudden, the key is being rejected. When we create a new instance with the keypair, we're able to connect to the instance perfectly, so it appears to be an issue with the existing instance. Port 22 is open. Any suggestions on what to look at from a configuration standpoint so we can fix this? Any thoughts on how we can get into the box? Here is the SSH debug output. Is there anything obviously amiss? Thanks so much! $ ssh -v -i ~/zzz.pem ubuntu@###.###.###.### OpenSSH_5.2p1, OpenSSL 0.9.8l 5 Nov 2009 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to ###.###.###.### [###.###.###.###] port 22. debug1: Connection established. debug1: identity file zzz.pem type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-6ubuntu2 debug1: match: OpenSSH_5.1p1 Debian-6ubuntu2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '###.###.###.###' is known and matches the RSA host key. debug1: Found key in /zzz/.ssh/known_hosts:18 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering public key: /zzz/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Offering public key: zzz.txt debug1: Authentications that can continue: publickey debug1: Trying private key: zzz.pem debug1: read PEM private key done: type RSA debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey).

Read the article

ASUS P8B WS - Endless Reboots

- by tuxGurl

I am running a Intel XEON 1245 with 4GBx2 Kingston Memory ECC Unbuffered DDR3 on an ASUS P8B WS motherboard. BIOS Version 0904 x64. This system is a little over a month old. It is running Ubuntu 11.10. This evening I found the machine turned off. When I tried to restart it, it would POST and stop at the GRUB screen. When I selected Ubuntu and hit enter within 2-3 seconds the would shutdown and restart. If I stayed at the GRUB screen and did nothing the system would not cut out. I tried booting off a USB stick and again 2-3 seconds after selecting 'Try Ubuntu without Installing' the machine will cut power and reboot. Things I have tried so far: Resetting the BIOS using the on board jumper Resetting the BIOS settings to default Disconnecting all external hardware - except keyboard & monitor Booting with 1 stick of RAM - I tried different single sticks Ensured that onboard EPU and GPU boost switches are in the off position. I am running a Memtest86 right now and it has been running for 38+ minutes. This is not an OS problem or an overheating issue (I have a CoolerMaster HAF Case with 3 fans besides the CPU fan) I am at a loss as to what to try next. I think the BIOS is mis-configured somehow but I don't know what to look for.

Read the article

How can I get MySQL 5.5 to log warnings to one of the log files?

- by Wodin

Read the article

iSCSI, failover and XenServer

- by jemmille

I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid> is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

Read the article

upstart config to start sync daemon as non-root user

- by Rudiger Wolf

I am planning to use inosync to sync data from master server to several client servers. I have created a user called rsyncuser in both master and slaves with access permissions and passwordless ssh access from master to slave servers. Inosync is working when I use it from the command line as rsyncuser. Next I want this to start automatically when server is turned on. I figured upstart is the way to get this working. I am unable to find the right upstart command to get this working. Here is my upstart conf file. The problem seems to be around running "inosync -d -c /etc/inosync/inosync_rsyncuser.py" as a given user. As you can see I have tried a number of various options! description "start inosync to sync data to other CDN Servers as rsyncuser" console output #start on startup #stop on shutdown start on (net-device-up and local-filesystems) stop on runlevel [016] #start on runlevel [2345] #stop on runlevel [!2345] #kill timeout 30 env RUN_AS_USER=rsyncuser expect fork script echo "Inosync updtart job seems to have started" /tmp/upstart.log # exec sudo -u rsyncuser -c "ls -la" /tmp/upstart.log 2&1 # LOGFILE=/var/log/logfile.`date +%Y-%m-%d`.log # exec su - $RUN_AS_USER -c "inosync -d -c /etc/inosync/inosync_rsyncuser.py" $LOGFILE 2&1 # exec su -c "ls -la" /tmp/upstart.log 2&1 # emit inosync_running end script

Read the article

Resize Debian in VirtualBox

- by Poni

I have a VM with one HD of size 3GB and I'd like to enlarge its HD to 7GB. So I execute this command on the host (while guest is shutdown): VBoxManage modifyhd debian.vdi --resize 7168 Then I run the guest, Debian 6, and then: smith@debian6:~$ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda1 2.8G 2.6G 60M 98% / tmpfs 61M 0 61M 0% /lib/init/rw udev 57M 160K 57M 1% /dev tmpfs 61M 0 61M 0% /dev/shm smith@debian6:~$ sudo parted /dev/sda print Model: ATA VBOX HARDDISK (scsi) Disk /dev/sda: 3221MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 3035MB 3034MB primary ext3 boot 2 3036MB 3220MB 185MB extended 5 3036MB 3220MB 185MB logical linux-swap(v1) smith@debian6:~$ cat /proc/partitions major minor #blocks name 8 0 3145728 sda 8 1 2962432 sda1 8 2 1 sda2 8 5 180224 sda5 So, no automatic resizing (detection) of the HD/partition (while VirtualBox, in the host, shows it's 7GB now). Ok... Then I do: smith@debian6:~$ sudo resize2fs /dev/sda1 resize2fs 1.41.12 (17-May-2010) The filesystem is already 740608 blocks long. Nothing to do! smith@debian6:~$ sudo parted GNU Parted 2.3 Using /dev/sda Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) select /dev/sda1 Using /dev/sda1 (parted) resize WARNING: you are attempting to use parted to operate on (resize) a file system. parted's file system manipulation code is not as robust as what you'll find in dedicated, file-system-specific packages like e2fsprogs. We recommend you use parted only to manipulate partition tables, whenever possible. Support for performing most operations on most types of file systems will be removed in an upcoming release. Partition number? 1 Start? 0 End? [3034MB]? Here I'm stuck. At the above parted it asks me to resize to 3GB. No point in that, right.. What should I do in order to enlarge this partition?

Search Results

Search found 2329 results on 94 pages for 'sudden shutdown'.

Page 72/94 | < Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79 | Next Page >

- by jemmille

- by PokermUNKEE

- by Ben

- by d3vid

- by buggedcom

- by lukewm

- by Kristofer O

- by gmuller

- by Sathya

- by Leniel Macaferi

- by Vnuk

- by Matt Johnson

- by Neil

- by antiduh

- by user42119

- by holmes

- by Filip Ekberg

- by Argh

- by Paul Robinson

- by shedd

- by tuxGurl

- by Wodin

- by jemmille

- by Rudiger Wolf

- by Poni

< Previous Page | 68 69 70 71 72 73 74 75 76 77 78 79 | Next Page >