Search Results

Search found 22427 results on 898 pages for 'opn program'.

Page 722/898 | < Previous Page | 718 719 720 721 722 723 724 725 726 727 728 729  | Next Page >

  • debian VM refusing all traffic apart from http

    - by james lewis
    I've got a VM with a fresh install of Debian (wheezy) and I've installed node and mongo on it. The VM is using a bridged network connection so I was expecting to be able to point my host machines browser at the ip address of the Debian VM (port 1337 for my node example or port 28017 for my mongo status page) and see one of the two services (node or mongo). My requests are refused though. As far as I can tell Debian allows all traffic by default and you have to manually configure iptables to drop traffic. I've checked iptables and it says it's setup to allow anything through. It looks like this: root@devbox:/home/jlewis# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination As a test I setup nginx and I was able to get to the nginx landing page from my host no problems so obviously http traffic is allowed. I then set nginx up to forward all traffic upstream to mongo - no problems there, I was able to see the status page. I then did the same for my example node server and again, no problems. So http traffic is fine, but all other traffic is blocked. Anyone know why debian might be refusing all other traffic other than iptables being setup to drop it? EDIT - output from netstat -nltp: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:28017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:51028 0.0.0.0:* LISTEN 1541/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2462/sshd tcp 0 0 127.0.0.1:1337 0.0.0.0:* LISTEN 2794/node tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2274/exim4 tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1510/rpcbind tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2189/nginx tcp6 0 0 :::22 :::* LISTEN 2462/sshd tcp6 0 0 :::45335 :::* LISTEN 1541/rpc.statd tcp6 0 0 ::1:25 :::* LISTEN 2274/exim4 tcp6 0 0 :::111 :::* LISTEN 1510/rpcbind

    Read the article

  • CryptSvc not matched by Windows 7 Firewall rule

    - by theultramage
    I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

    Read the article

  • Looking for recommendations on OCR problem - tabular numeric data

    - by ldigas
    I have 20 pages of experiment measurement data which I need to digitalize. The results are in tabular form, scanned in 600 dpi resolution, and as far as scans go, they came up pretty clean and readable. For an example of how it looks see here (but beware: it is a rather big scan; about 5Mb; no problem for any broadband connection, but dialups should approach with caution!) ... and I need it finished by sunday afternoon (:-o) <-- smiley in a state of panic (then why did't you start sooner?)... yea, yeah ... I know ... but, it came up late, and I wasn't thinking I was gonna need this data also. So, I'm looking for recommendations. I haven't much experience with OCR programs, save scanning a page or two of pure text, but just to mention, I haven't the wish also to test out every OCR program out there. So this isn't a "name your OCR favourite". What I'm looking is advice from someone who's done something like that, and his/hers experience on what would be the best way to undertake. I need the data in txt form but since it will have to be checked (by drawing it, and just simply watching whether some points "jump out") I'll probably be entering it in Excel at first.

    Read the article

  • How to uninstall files and software from a Solid State Drive (SSD)

    - by jasondavis
    I am using a SSD drive just as a main Operation system and software drive. I have a regular spinning disk for data files. I have read that files are not REALLY deleted from a SSD drive when you "delete" them. So here is my situation and hopefully I can get some good advice. Let's say I have Windows 7 Pro x64bit installed on my 80gb Intel SSD. I then have Adobe Photoshop CS4 installed along with 50 other programs installed onto this SSD. I then decide I am done with Adobe Phjotoshop CS4 and want to remove it. I then decide I want to install another version of Adobe Photoshop and a few other software titles. Would I just do the usual, add/remove software from the windows control panel. Or if the software being removed has an "Uninstall" program to run, then run it and uninstall the software? I realize that all this WILL remove the software from Windows 7 but I am wanting to know if there is additional steps that should be taken since it is a solid state drive (SSD)?

    Read the article

  • 8007064c(2011) and 80280007(2009) persistant after all known repairs

    - by tiu44
    I'm on Windows 7 Home x64, and have ran into a major issue with Live Messenger(which I use daily). I have full offline installers for both 2011 and the last Wave 3 2009(14.0.8117.0416) Suites. Both give the following errors: Live Essentials 2011 Offline installer(official): An unknown error occured. Error:0x8007064c Source WLXSuite WL 2009 offline installer(official): You already have a more recent version of Windows Live. Error: OnCatalogResult:0x80280007 Next steps: If you want to install this older version, first uninstall any later versions that are on your computer. Get help with this error The 2011 installer also says it is updating messenger, I don't select anything else. Then last 2009 installer says their is a newer version that needs uninstalled even after the following procedures. MS Help pages provided all basically lead to using uninstall from control panel. Which I've uninstalled all Live components including watcom safety scanner and portable SQL from. I've followed online instructions for manually deleting folders from Program Files(x86), Appdata, and some others under \User\All Users and the one for the one account on the machine. I've used CCcleaner 3.01, ASC 3.7.3 and Beta 4 with deep scan along with deleting folders, and checked their uninstallers for Live components too, and none were there. wlmuninstaller.exe tool reports nothing, but after a failed install it finds something, but failes to clean it under all user admin privilege. The same errors still occur after all of that. Google searching I see people on forums suggesting reinstalling the OS cause MS doesn't even know how to fix this, but I'm hoping someone here can help. NOTE: I don't have System Restore or any other state freeze utilities going, and I don't have any real time AV going(I sometime scan with defender, anti rootkits, and online scanners). NOTE2:I posted this on windowslivehelp.com, before looking to see if the place was active or not, hoping I can get help here. Thanks

    Read the article

  • Users database empty after Samba3 to Samba4 migration on different servers

    - by ouzmoutous
    I have to migrate a Samba 3 to a new Samba 4 server. My problem is that the database on the samba 3 server seems a bit empty. The secrets.dtb file is only 20K whereas the “pbedit -L |wc -l”command give me 16970 lines. On my Samba3 /var/lib/samba is 1,5M After I had migrate the databse (following instructions on http://dev.tranquil.it/index.php/SAMBA_-_Migration_Samba3_Samba4), “pdbedit -L” command on the new server give me only : SAMBA4$, Administrator, dns-samba4, krbtgt and nobody. So I tried to create a VM with a Samba3. I added some users, done the same things I did for the migration and now I can see the users created on the VM. It’s like users on the Samba 3 server are in a sort of cache. I already migrate the /etc/{passwd,shadow,group} files and I can see users with the “getent passwd” command. Any ideas why my users are present when I use pdbedit but the database is so empty ? The global part of my smb.conf on the Samba 3 server : [global] workgroup = INTERNET netbios name = PDC-SMB3 server string = %h server interfaces = eth0 obey pam restrictions = Yes passdb backend = smbpasswd passwd program = /usr/bin/passwd %u passwd chat = *new* %n\n *Re* %n\n *pa* username map = /etc/samba/smbusers unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%U max log size = 1000 socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192 add user script = /usr/sbin/useradd -s /bin/false -m '%u' -g users delete user script = /usr/sbin/userdel -r '%u' add group script = /usr/sbin/groupadd '%g' delete group script = /usr/sbin/groupdel '%g' add user to group script = /usr/sbin/usermod -G '%g' '%u' add machine script = /usr/sbin/useradd -s /bin/false -d /dev/null '%u' -g machines logon script = logon.cmd logon home = \\$L\%U domain logons = Yes os level = 255 preferred master = Yes local master = Yes domain master = Yes dns proxy = No ldap ssl = no panic action = /usr/share/samba/panic-action %d invalid users = root admin users = admin, root, administrateur log level = 2

    Read the article

  • After update to Windows 8.1 brigthness isn't working (changing)

    - by Bibo
    I just update my Windows 8 to Windows 8.1 by Windows Store and I have some problems. My notebook is Acer Aspire Timelinex 3820TG and I know it's little old for Windows 8 but I install them and works fine (I updated my HDD to SSD). Now I just updated Windows and I have problem with changing brightness on my dedicated graphic card (Ati HD 5650). First I can changing brigthness with fn + keys but It just changing level in OS. No change in real. I tried reinstall drivers, install drivers for my card from Acer with compatibility to Windows 7 and without change. When I switch to integrated card changing brightness works. I think the problem is with drivers but I don't know how to get it working. Thanks for help Bonus question: I have another problem (but this one is not so important). Does anyone knows what msietxghh.exe is doing? Everytime when my system runs (after update) I get message that this program stops working but I just cancel and looks everything works fine.

    Read the article

  • How to create btrfs RAID-1 filesystem (assertion error in mkfs.btrfs)?

    - by amcnabb
    I tried to make a btrfs RAID-1 filesystem in "degraded mode" by following the btrfs UseCases instructions but hit a fatal assertion error. Why is this failing, and is there any workaround? The instructions I followed are at: https://btrfs.wiki.kernel.org/articles/u/s/e/UseCases_8bd8.html The output of the mkfs.btrfs and btrfs filesystem show commands is: # mkfs.btrfs -m raid1 -d raid1 /dev/sdd1 /dev/loop1 WARNING! - Btrfs Btrfs v0.19 IS EXPERIMENTAL WARNING! - see http://btrfs.wiki.kernel.org before using failed to read /dev/sr0 adding device /dev/loop1 id 2 mkfs.btrfs: volumes.c:802: btrfs_alloc_chunk: Assertion `!(ret)' failed. zsh: abort (core dumped) mkfs.btrfs -m raid1 -d raid1 /dev/sdd1 /dev/loop1 # btrfs filesystem show failed to read /dev/sr0 Label: none uuid: 773908b8-acca-4c30-85c5-6642b06de22b Total devices 1 FS bytes used 28.00KB devid 1 size 223.13GB used 2.04GB path /dev/sda5 Label: none uuid: 0f06f1a8-5f5f-4b92-a55c-b827bcbcc840 Total devices 2 FS bytes used 24.00KB devid 2 size 2.00GB used 0.00 path /dev/loop1 devid 1 size 1.36TB used 20.00MB path /dev/sdd1 Btrfs Btrfs v0.19 # EDIT: It turns out that the filesystem isn't mountable: # mount /dev/sdd1 /mnt/big2 mount: wrong fs type, bad option, bad superblock on /dev/sdd1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so # So, why did the mkfs fail, and is there any workaround?

    Read the article

  • Transparent proxying in MacOS X 10.6 Snow Leopard (and maybe FreeBSD)

    - by apenwarr
    I'm trying to create a transparent proxy on my MacOS machine in order to port the sshuttle ssh-based transproxy VPN from Linux. I think I almost have it working, but sadly, almost is not 100%. Short version is this. In one window, start something that listens on port 12300: $ while :; do nc -l 12300; done Now enable proxying: # sysctl -w net.inet.ip.forwarding=1 # sysctl -w net.inet.ip.fw.enable=1 # ipfw add 1000 fwd 127.0.0.1,12300 log tcp from any to any And now test it out: $ telnet localhost 9999 # any port number will do # this works; type stuff and you'll see it in the nc window $ telnet google.com 80 # any host/port will do # this *doesn't* work! After the latter experiment, I see lines like this in netstat: $ netstat -tn | grep ^tcp4 tcp4 0 0 66.249.91.104.80 192.168.1.130.61072 SYN_RCVD tcp4 0 0 192.168.1.130.61072 66.249.91.104.80 SYN_SENT The second socket belongs to my telnet program; the first is more suspicious. SYN_RCVD implies that my SYN packet was correctly captured by the firewall and taken in by the kernel, but apparently the SYNACK was never sent back to telnet, because it's still in SYN_SENT. On the other hand, if I kill the nc server, I get this: $ telnet google.com 80 Trying 66.249.81.104... telnet: connect to address 66.249.81.104: Connection refused telnet: Unable to connect to remote host ...which is as expected: my proxy server isn't running, so ipfw redirects my connection to port 12300, which has nobody listening on it, ie. connection refused. My uname says this: $ uname -a Darwin mean.local 10.2.0 Darwin Kernel Version 10.2.0: Tue Nov 3 10:37:10 PST 2009; root:xnu-1486.2.11~1/RELEASE_I386 i386 Does anybody see any different results? (I'm especially interested in Snow Leopard vs Leopard results, as there seem to be some internet rumours that transproxy is broken in Snow Leopard version) Any advice for how to fix?

    Read the article

  • Exchange DiskShadow/Robocopy backup does not purge log files

    - by Robert Allan Hennigan Leahy
    I have a series of scripts setup to backup my Exchange. The following command is executed to start the process: diskshadow /s C:\Backup_Scripts\exchangeserverbackupscript1.dsh This is exchangeserverbackupscript1.dsh: #DiskShadow script file set verbose on #delete shadows all set context persistent writer verify {76fe1ac4-15f7-4bcd-987e-8e1acb462fb7} set metadata C:\Backup_Scripts\shadowmetadata.cab begin backup add volume C: alias SH1 create expose %SH1% P: exec C:\Backup_Scripts\exchangeserverbackupscript1.cmd end backup delete shadows exposed P: exit #End of script And this is exchangeserverbackupscript1.cmd: robocopy "P:\Program Files\Microsoft\Exchange Server\Mailbox\First Storage Group" "\\leahyfs\J$\E-Mail Backups\Day 1" /MIR /R:0 /W:0 /COPY:DT /B This is not causing Exchange to purge its log files. The edb file is 4.7 gigabytes, but the First Storage Group folder itself is 50+ gigabytes due to many, many log files for each day going back to 2009. Is there any way -- I've Googled and haven't found anything -- to notify Exchange when I've completed a full backup, and have it purge its log files? According to this and this, end backup should cause Exchange to "flush the transaction logs for that storage group" but only "if a successful backup of a storage group occurred", which leaves my question as: What constitutes a "successful backup", and why is what I'm doing not it?

    Read the article

  • (13) Permission denied on Apache CGI attempt

    - by ncv
    I have recently upgraded my Apache2 server, and am now unable to run a CGI app. My logs are showing (13) Permission denied unable to connect to cgi deamon after multiple tries I understand that the error message means Apache is being denied some permission to some file, and I'm stumped as to how to track down and solve the problem. Is the file mentioned in the error message truly the blocked file? Or might the problem be caused by some other needed file? The .cgi file is right where it has always been, under /usr/share. The file ownership (root) and permissions (world readable/executable) are the same as they have always been for the file and its ancestors. The SELinux file labels are unchanged. The SELinux audit log shows no denial associated with Apache nor the CGI program. In case of a donotaudit condition, I enabled audit, but still saw nothing. I switched SELinux into permissive mode briefly, to no avail. I even tried restarting Apache while in permissive mode. This did not solve the problem. Any suggestions on how to solve this problem? I'm tempted to just revert to the older Apache.

    Read the article

  • unable to destroy windows 2008 r2 failover cluster after SAN rebuild

    - by Zack
    I created a windows 2008 r2 failover cluster for a sql 2008 active/passive cluster. This two node cluster was using a SAN device for a quorum disk resource as well as MSDTC resource. Well....I decided to reconfigure the SAN device, but I didn't destroy the cluster first. Now that the quorum disk and mstdc disk are completely gone, the cluster is obviously not working. But, I can't even destroy the cluster and start again. I've tried from the Windows Clustering tool, as well as the command line. I was able to get the cluster service to start using the "/fixquorum" parameter. After doing this I was able to remove the passive node from the cluster, but it wouldn't let me destroy the cluster because the default resource group and msdtc are still attached as resources. I tried to delete these resources from both the GUI tool, as well as command line. It will either freeze for several minutes and crash the program, or once it even BSOD'd the server. Can someone advise on how to destroy this cluster so I can start over?

    Read the article

  • Automated Scanning for Corrupted Archive Files

    - by Synetech inc.
    Hi, I have all kinds of files that I have downloaded from everywhere over the years scattered around my hard drives. I’m in the process of trying to organize them all and have run into a problem. Sometimes a file was not downloaded correctly (this was a big issue when Chromium first came out) and is thus corrupt. For media files, this is relatively simple to determine (it requires actually opening and examining the file). For executables or other binaries, it is relatively difficult (executables may or may not crash, other binaries could be completely unknown). Archive files (eg zip, rar, 7z, exe, ace, etc.) however should be pretty simple, they have a built-in corruption detection facility. My problem now is that I really don’t want to open and test each and every single archived file throughout my drive; that would be a nightmare. I’m looking for a utility that can automate the process. Is there a program that can scan archive files on a drive and list the ones that are corrupt? Thanks a lot.

    Read the article

  • Problems mounting HPUX LVM+VXFS filesystem on Linux

    - by golimar
    I have a physical disk from a HPUX system that I need to access from a Debian Linux for ia64 system. From the hpux-lvm-tools project I have the tools to access the HPUX LVMs (Linux LVM has a different format) and I also have the freevxfs driver. I know beforehand that the disk has three partitions, and that the biggest one contains LVM volumes, and some of those are VxFS filesystems. I can see the partitions: # cat /proc/partitions major minor #blocks name 8 32 143374744 sdc 8 33 512000 sdc1 8 34 142452736 sdc2 8 35 409600 sdc3 It finds a VG in one of the disk partitions: # ./vgscan_hpux On /dev/sdc2 - vg1328874723 # ./pvdisplay_hpux /dev/sdc2 PV General Information ---------------------- VG Creation Time Fri Feb 10 12:52:03 2012 Physical Volume ID 1766760336 1328874723 Volume Group ID 1766760336 1328874723 Physical Volumes in VG 1766760336 1328874723 VG Actication Mode 0 - LOCAL PE Size 64 MBs Lvol sizes ---------- lvol1 - 8 Extents - 512 MBs lvol2 - 192 Extents - 12288 MBs lvol3 - 16 Extents - 1024 MBs ... lvol21 - 13 Extents - 832 MBs lvol22 - 224 Extents - 14336 MBs lvol23 - 16 Extents - 1024 MBs Then I activate that VG and some new devices appear in my system: # ./pvactivate_hpux /dev/sdc2 VG vg1328874723 Activated succesfully with 23 lvols. # # ll /dev/mapper/ total 0 crw------- 1 root root 10, 59 Nov 26 16:08 control lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol1 -> ../dm-0 lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol10 -> ../dm-9 ... lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol8 -> ../dm-7 lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol9 -> ../dm-8 But: # mount /dev/mapper/vg1328874723-lvol18 /mnt/tmp mount: you must specify the filesystem type # mount -t vxfs /dev/mapper/vg1328874723-lvol18 /mnt/tmp mount: wrong fs type, bad option, bad superblock on /dev/mapper/vg1328874723-lvol18, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so # lsmod |grep vxfs freevxfs 23905 0 I also tried to identify the raw data with the file command and it just says 'data': # file -s /dev/mapper/vg1328874723-lvol18 /dev/mapper/vg1328874723-lvol18: symbolic link to `../dm-17' # file -s /dev/dm-17 /dev/dm-17: data # Any clues?

    Read the article

  • How do I configure custom URL handlers on OS X?

    - by cwd
    I've been reading a lot online about custom URL handlers / custom protocol handlers such as: Launching External Applications using Custom Protocols under OSX OS X URL handler to open links to local files I get that you can tell the system that a particular program is able to handle a certain scheme / protocol with the Info.plist file: <key>CFBundleURLTypes</key> <array> <dict> <key>CFBundleURLName</key> <string>Local File</string> <key>CFBundleURLSchemes</key> <array> <string>local</string> </array> </dict> </array> <key>NSUIElement</key> <true/> But if there are multiple applications that are capable of opening the same URL handler, such as mailto: how do you specify which one you want the system to use? There were some references to utilities like the More Internet preference pane which no longer seems to be available from the author's site. I did find it online by Googling but it seems a bit shaky - like it was written for an older OSX - perhaps Tiger. I haven't been able to find information on how to set the URL handler for protocols and custom protocols. I'm assuming there is a plist file somewhere that I can edit - or maybe there is a newer, better utility that works well with Mountain Lion?

    Read the article

  • SMTP error goes directly to Badmail directory after Queue

    - by Sergio López
    This is the error I got in the .BDR Unable to deliver this message because the follow error was encountered: "This message is a delivery status notification that cannot be delivered.". The specific error code was 0xC00402C7. The message sender was <. The message was intended for the following recipients. [email protected] This is the .bad file I got in the badmail error, Can anyone help me ? I´m getting this error from every mail I try to deliver from several php apps and other apps, the relay is only for 2 ip adresses 127.0.0.1 and the server ip, I telnet the smtp and it seems to work fine the mail go to the queue folder... Im stucked From: postmaster@ALRSERVER02 To: [email protected] Date: Mon, 22 Aug 2011 18:39:38 -0500 MIME-Version: 1.0 Content-Type: multipart/report; report-type=delivery-status; boundary="9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02" X-DSNContext: 7ce717b1 - 1378 - 00000002 - C00402CF Message-ID: Subject: Delivery Status Notification (Failure) This is a MIME-formatted message. Portions of this message may be unreadable without a MIME-capable mail program. --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: text/plain; charset=unicode-1-1-utf-7 This is an automatically generated Delivery Status Notification. Delivery to the following recipients failed. [email protected] --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: message/delivery-status Reporting-MTA: dns;ALRSERVER02 Received-From-MTA: dns;ALRSERVER02 Arrival-Date: Mon, 22 Aug 2011 18:39:38 -0500 Final-Recipient: rfc822;[email protected] Action: failed Status: 5.3.5 --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: message/rfc822 Received: from ALRSERVER02 ([74.3.161.94]) by ALRSERVER02 with Microsoft SMTPSVC(7.0.6002.18264); Mon, 22 Aug 2011 18:39:38 -0500 Subject: =?utf-8?Q?[MantisBT]_Reinicializaci=C3=B3n_de_Contrase=C3=B1a?= To: [email protected] X-PHP-Originating-Script: 0:class.phpmailer.php Date: Mon, 22 Aug 2011 17:39:38 -0600 Return-Path: [email protected] From: Alr Tracker Message-ID: X-Priority: 3 X-Mailer: PHPMailer 5.1 (phpmailer.sourceforge.net) MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Content-Type: text/plain; charset="utf-8" X-OriginalArrivalTime: 22 Aug 2011 23:39:38.0020 (UTC) FILETIME=[C182E640:01CC6124] Si solicitó este cambio, visite la siguiente URL para cambiar su contraseña: Usuario: slopez Dirección IP remota: 189.191.159.86 NO RESPONDA A ESTE MENSAJE --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02--

    Read the article

  • Need advice on a monitoring, reminder and warning application.

    - by cbmeeks
    I am a developer that also has to monitor several things on different servers. Such as: 1) Did all of the MS SQL databases backup last night? 2) Did all of the MySQL databases backup last night? 3) Were the database dumps actually copied to the right folder? 4) How much free space is left on each server's hard drives? 5) How big are folders "abc", "def", "etc" getting? 6) Send emails/alerts when thresholds are reached Etc. Just basically something to help me NOT forget such important things. I thought about writing something myself but didn't want to waste the effort if something is already out there. I would also prefer one application instead of many if I could. Thanks. EDIT Forgot to mention the operating system. These run on Windows Server 2003 and/or 2008. In fact, what would be cool is a program that supports multiple servers from one machine. Something that can log into those servers.

    Read the article

  • How to embed Arial in PDF when PDF has Helvetica?

    - by Brooks Moses
    So, I've got a PDF file that's generated by a program that uses the Base 14 fonts, so that it contains "Helvetica" and "Times Roman". When I look at that in my copy of Acrobat 7.0 on Windows (for example), it shows these with Arial and Times New Roman. I'm fine with that. The issue is that I'd like to publish this PDF file on lulu.com, and they want all fonts embedded. Including the Base 14. I don't have a copy of Helvetica, so what seems the natural thing to do is substitute Arial for Helvetica and embed Arial. How can I do that? I tried using the Print feature in Acrobat (note: this is the full version, not Reader) to print to a PDF file using Adobe's "Print to PDF" printer driver, and selected the "Embed All Fonts" option in the print settings. This worked for the fonts that I had actual copies of, but instead of "printing" Arial for Helvetica -- which it would do if printing to a real printer -- it leaves all the Helvetica as Helvetica and doesn't embed it. Any suggestions for alternate ways to do this? What I really want is just a copy of my PDF file with ALL fonts embedded, and I'm quite happy if doing that means making one of the usual substitutions for the "Helvetica" that's in it. I'd be happiest if I can do that within Acrobat or other software that I have (pdftex, maybe?), but I'm willing to install another free utility if I need to.

    Read the article

  • Shared printer hosted by Windows 7 to XP peers [closed]

    - by Alistair Knock
    Possible Duplicate: Add Network Printer drivers in Windows 7/Server 2008 R2? A Canon Pixma ip4600 installed all by itself when connected to a Windows 7-64 bit machine. I then updated it with the add-on Canon provide to give additional functionality. I then wish to share it with a box which is running Windows XP 32-bit. The XP box can see the printer but can't find a driver from the 7 machine, which is fine. I ask the 7 machine to get the x86 drivers, but it can't. I install the 32-bit XP drivers on the XP machine, but unlike previous Canon drivers (which unzip to give an .inf file), they assume a local printer and partially give up. I find the .inf file in the Program files\CanonBJ\... directory. Neither the XP machine, nor the 7 machine when the CanonBJ directory is shared to it, is happy with the .inf file. I attempt to install the 32-bit drivers on the 64-bit 7 machine, which, understandably, fail. Where do we go from here? (I apologise for posting in the first-person, I'm not sure why this was)

    Read the article

  • Scanning website for vulnerablities

    - by Kristen
    I have found that the local school's website installed a Perl Calendar - this was years ago, it has not been used for ages, but Google has it indexed (which is how I found it) and it full of Viagra links and the like ... program was by Matt Kruse, here is details of the exploit: http://www.securiteam.com/exploits/5IP040A1QI.html I've got the school to remove that, but I think they also have MySQL installed and I'm aware that out-of-the-box there have been some exploits of Admin Tools / Login in old versions. For all I know they also have PHPBB and the like installed ... The school is just using some cheap, shared hosting; the HTTP response header I get is: Apache/1.3.29 (Unix) (Red-Hat/Linux) Chili!Soft-ASP/3.6.2 mod_ssl/2.8.14 OpenSSL/0.9.6b PHP/4.4.9 FrontPage/5.0.2.2510 I'm looking for some means of checking if they have other junk installed (quite possibly from way back, and now unused) that might put the site at risk. I'm more interested in something that can scan for things like the MySQL Admin exploit rather than open ports etc. My guess is that they have little control over the hosting space that they have - but I'm a Windows DEV, so this *nix stuff is all Greek to me. I found http://www.beyondsecurity.com/ which looks like it might do what I want (within their evaluation :) ) but I have a worry about how to find out if they are well known / honest - otherwise I will be tipping them a wink with a Domain Name that may be at risk! Many thanks.

    Read the article

  • How to connect to Oracle DB via ODBC

    - by Mat
    I am attempting to connect to a remote Oracle DB via ODBC. I am totally inexperienced and fail to connect. What I have installed: Oracle 'ODBC Driver for RDB' A program I want to connect from (Altova Mapforce, an ETL) What I do: Under Administrative tools I open the Windows "ODBC Data Source Administrator I click 'Add..' and select the Oracle ODBC Driver The Window 'Oracle RDB Driver Setup' opens. I fill in: Data source name: free choice Description: I leave blank Transport: I choose TCP/IP Server: I input the IP address of the server Service: I leave 'generic' UserID: I enter the user name (that belongs to the password I have) Attach Statement: no idea what do do here?? Upon choosing 'OK', the 'Oracle RDB ODBC Driver Connect' opens and I am prompted the password. I enter the password and the connection fails. Questions Do I need further programs on my computer, e.g. the Oracle client of Instant client? I am never prompted the port of the server - isn't this relevant? I am never prompted SID - isn't this relevant? I connected from SQL developer easily - it prompted only server IP, port, username, password and SID.

    Read the article

  • Fresh Install of SQL Server 2008 doesn't install managment studio. Help!

    - by Jordan S
    Ok I am running Windows 7, 64 bit. I cleaned of SQL server 2005 completely off my system leaving only SQL Compact Edition. I went here http://www.microsoft.com/downloads/details.aspx?FamilyID=01af61e6-2f63-4291-bcad-fd500f6027ff&displaylang=en and installed SQL Server 2008 Express Edition Service Pack 1. After the install, under my start bar menu all i have for SQL configuration tools are the Configuration Manager, Error and Usage Reporting and the Install Center. I don't have the SQL Managment Studio. So I went here http://www.microsoft.com/downloads/details.aspx?FamilyID=08e52ac2-1d62-45f6-9a4a-4b76a8564a2b&displaylang=en and downloaded the SQL Server 2008 Management Studio Express but when I try to install it I get a warning says This program has known compatibility issues and that I need to Install SQL Server 2008 Service Pack 1. I thought that is what I installed. So, I tried to continue running the install but I then get an error message that says Invoke or BeginInvoke can not be called on a Form before it is opened... How can I check if Service pack 1 is installed or not? What should I do?

    Read the article

  • SQL 2008 SP1 crashing almost daily

    - by matijake
    Hey, almost every day our new DB crashes. It is virtual server residing on same hardware as 5 other servers, two of them beeing identical MS SQL2008sp1 and two Oracle 11g's so I can pretty much rule out hardware issues. Server has dedicated local LUN, 4vCPU and 8GB memory with 2GB windows swap file. It runs 4 instances. Primary instance is limited to 5GB memory and paralelism set to 4 running on MS SQL 2008 SP1 @ Windows Server 2008 Enterprise R2 x64. Only that primary instance is crashing. After it crashes nothing can connect to it, it's even impossible to shut it down through service manager. What I found in logs is: ***Stack Dump being sent to C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\LOG\SQLDump0081.txt SqlDumpExceptionHandler: Process 4788 generated fatal exception c0000005 EXCEPTION_ACCESS_VIOLATION. SQL Server i s terminating this process.     Whole log can be seen at: http://kabl.org/files/SQLDump0081.txt second crash log made second later at: http://kabl.org/files/SQLDump0082.txt I have analyzed mini crashdump with Microsoft tools, but no promising results. If it can help, here it is: http://kabl.org/files/SQLDump0081.mdmp Any ideas are greatly welcome, since it is becoming quite a pain in the ass to restart server almost every day :) Regrads, -Matija

    Read the article

  • Specific DNS sometimes resolves to wildcard, incorrectly

    - by Mojo
    I have an intermittent problem, and I'm not sure where to start trying to troubleshoot it. In our dev environment, we have two visible IP addresses on load balancers, one to the front-end, and one to a number of back-end service machines. The front-end is configured to take a wildcard DNS name to support generic "portals." dev.example.com A 10.1.1.1 *.dev.example.com CNAME dev.example.com The back-end servers are all specific names within the same space: core.dev.example.com A 10.1.1.2 cms.dev.example.com CNAME core.dev.example.com search.dev.example.com CNAME core.dev.example.com Here's the problem. Periodically a developer or a program trying to reach, say, cms.dev.example.com will get a result that points to the front-end, instead of the back-end load balancer: cms.dev.example.com is an alias to core.dev.example.com core.dev.example.com is an alias to dev.example.com (WRONG!) dev.example.com 10.1.1.1 The developers are all on Mac OS X machines, though I've seen the problem occur on an Ubuntu machine as well, using a local cloud host DNS resolver. Sometimes the developer is using a VPN, which directs the DNS to its own resolver, and sometimes he's on the local net using a DNS resolver assigned by the NAT router. Sometimes clearing the Mac OS X DNS cache, logging into the VPN, then logging out of the VPN, will make the problem go away. The origin authoritative server is on zerigo, and a dig directly to their name servers always seems to give the correct answer. The published DNS cache time for these records is 15 minutes, but the problem has been intermittent for about a week. Any troubleshooting suggestions?

    Read the article

  • IIS 7 + Tomcat 7 - how to reach http://localhost:8080/my_app under e.g. http://my_app.local

    - by Sk8erPeter
    In brief: IIS 7 + Apache Tomcat 7 + isapi_redirect.dll: I have a deployed and working Tomcat-application available under http://localhost:8080/my_app. I would like to see the same content under http://my_app.local (and NOT the default Tomcat-site [which you can see below]). How can I do that? Longer explained: I have IIS 7 (7.5.7600.16385) and Apache Tomcat/7.0.22 installed. I deployed an application (let's call it "my_app") in Tomcat, which now can be reached at http://localhost:8080/my_app, works fine. I added a new web site in IIS panel with the path of the Tomcat deployed my_app, which looks like this: "c:\Program Files\Apache Software Foundation\Tomcat 7.0\webapps\my_app" I binded the host name my_app.local. After that, I configured isapi_redirect.dll like this (or that). Now, when I open http://my_app.local, I can see the default Tomcat site (see below). BUT under http://my_app.local I would like to see the same content as under http://localhost:8080/my_app. How can I do that? Thank you very much in advance!! my config files: isapi_redirect.properties (I made a dir junction to c:\tomcat, so this also works :) ) workers.properties uriworkermap.properties rewrites.properties (empty)

    Read the article

< Previous Page | 718 719 720 721 722 723 724 725 726 727 728 729  | Next Page >