Search Results

Search found 4065 results on 163 pages for 'intel mkl'.

Page 73/163 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Ping: sendmsg: operation not permitted error after installing iptables on Arch GNU/Linux

  - by estol

  Yesterday I got a new computer as my homeserver, a HP Proliant Microserver. Installed Arch Linux on it, with kernel version 3.2.12. After installing iptables (1.4.12.2 - the current version afaik) and changing the net.ipv4.ip_forward key to 1, and enabling forwarding in the iptables configuration file (and rebooting), the system cannot use any of its network itnerfaces. Ping fails with Ping: sendmsg: operation not permitted If I remove iptables completely, networking is okay, but I need to share the Internet connection to the local network. eth0 - wan NIC integrated on the motherboard (no idea of vendor, probably HP). eth1 - lan NIC in a pci-express slot (Intel Gigabit CT Desktop http://www.intel.com/content/www/us/en/network-adapters/gigabit-network-adapters/gigabit-ct-desktop-adapter.html) Since it works without iptables(server can access the internet, and I can login with ssh from the internal network), I assume it has something to do with iptables. I do not have much experience with iptables, so I used these as reference (separate from each other of course...): wiki.archlinux.org/index.php/Simple_stateful_firewall#Setting_up_a_NAT_gateway revsys.com/writings/quicktips/nat.html howtoforge.com/nat_iptables On my previous server, I used the revsys guide to set up nat, worked like a charm. Anyone experienced anything like this before? What am I doing wrong? Thanks, estol

  Read the article

• How to use Windows mini-dump files?

  - by ekaj

  I have a Mini-ITX Intel DH61AG mobo w/ an Intel i3 processor and 8GB of 1600MHz DDR3 RAM. Anyways, this computer has been crashing kind of frequently. It is not an OS problem, as I have used Ubuntu (and had kernel panics), Windows 7, and Windows 8 (BSODs aren't going to keep me from tinkering =p) Anyways, each of these OSes have had problems, so I ran a HDD check, and I know it is not a heat issue because I tested the processor for a few days when I first put the computer together. When I ran memtest86+, however, I got an error - so I did individual testing, and both chips came back good, did a really intense test with both of them again (took half a day), and no errors. So, I still think the problem could be RAM, but I am not sure - I tested it pretty extensively (might let it run all night again tonight)... which brings me to my point. Could someone explain to me (in simple terms if possible) how to READ the minidump files of Windows computers? I've tried before with a guide I found online, but failed miserably (can't remember guide, either =/). I'm fine with installing the software, I will probably need it sometime in the future as well. I have seen a few other posts on SU that just ask people to post minidump logs, but I feel as if that is too localized. Would someone be able to explain this? Note: If someone knows how to do this, but doesn't want to explain and is still willing to help me, this is the link for the minidump file =p Make sure to click

  Read the article

• How to improve Windows Server 2008 R2 to handle many connections?

  - by invisal

  It has been a few days so far that I am trying to figure how to solve this problem. First of all, I am running a website with an average daily page view of 350,000. Previously, all ads management (tracking click and impression that each ads has served) and content were served in a single server with the following spec: Server 1 OS: Windows 2008 R2 64-Bit CPU: Intel® Core™ i5 - 4 cores RAM: 8 GB Storage: 2 x 1 TB hard drives Bandwidth: 10 TB per month To improve our website speed, I decided to separate the ads management script to another dedicated server because we have more than 15 advertisers to 30 advertisers per each page. Server 2 OS: Windows 2008 R2 64-Bit CPU: Intel® Core™ i5 - 4 cores RAM: 4 GB Storage: 2 x 300 GB hard drives Bandwidth: 10 TB per month The Problem The problem is that Server 1 can handle both content and ads system. Now, that I take away the ads system and put it at Server 2. Server 2 can barely serve only ads system. Test First of all, I moved 75% of the ads to Server 2. And then, perform a ping to server: ping -t xxxxx. [I did the ping for 10 minutes and its following similar pattern as below] Reply from xxxxx bytes=32 time=290ms TTL=116 Reply from xxxxx bytes=32 time=289ms TTL=116 Reply from xxxxx bytes=32 time=320ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Reply from xxxxx bytes=32 time=348ms TTL=116 Reply from xxxxx bytes=32 time=284ms TTL=116 Then, I moved 100% of the ads to Server 2. Then, perform a ping to server again. [I did the ping for 10 minutes and its following similar pattern as below] Reply from xxxxx bytes=32 time=290ms TTL=116 Request timed out Reply from xxxxx bytes=32 time=320ms TTL=116 Reply from xxxxx bytes=32 time=286ms TTL=116 Request timed out Request timed out Reply from xxxxx bytes=32 time=284ms TTL=116 Attempts Increase MaxUserPort and TcpNumConnection Restart the server Increase IIS Max Instances and Instance MaxRequests Server Resource Only 10%-15% of the network connection is used Only 10%-15% of the CPU is used Only 25% of the memory is used

  Read the article

• SQL Server Express backup/restore error: The Media Family on Device is Incorrectly Formed.

  - by Chris

  Basically, I'm having this issue: http://www.sqlcoffee.com/Troubleshooting047.htm What I'm doing is running a script I found online (http://pastebin.com/3n0ZfybL) to do a full backup, then rar'ing up the file and moving it to my computer. The CRC of the backup file inside the rar is correct on both computers, so there is no problem with data being corrupted when I transfer it. But then I go and try to restore the database on my dev computer here and I get the errors "sql server cannot process this media family" ... "msg 3013". Why is this happening? I'd test out the backup on the server I'm getting it from, but it's a production server. Edit: I was about to say how I wasn't doing anything stupid like trying to restore the database to an earlier version of SQL Server, but apparently I am: From: Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (Intel X86) Mar 29 2009 10:27:29 Copyright (c) 1988-2008 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6002: Service Pack 2) To: Microsoft SQL Server 2005 - 9.00.3042.00 (Intel X86) Feb 9 2007 22:47:07 Copyright (c) 1988-2005 Microsoft Corporation Express Edition on Windows NT 6.0 (Build 6001: Service Pack 1) Let me get back to this post after I reinstall this.

  Read the article

• Lag in Windows 7 with Zepto Znote 6224W

  - by Xink64

  Hi! Why does my Zepto Znote 6224W Laptop with Windows 7 make these small laggy moves whenever I use it? First I installed Windows 7 64 bit because of the memorycap in Windows 7 32 bit, but soon I realized that the system was lagging randomly. It was very annoying whenever I listened to music, because of the sudden lags. Then I tried everything with drivers; Chipset, Soundcard, Graphicscard, and so on. No luck. I then installed Windows 7 32 bit and this reduced the amount of lags but they are still here. I haven't tried bios upgrade since my bios should be newest according to now the now bankrupt Zepto company. My specifications: Zepto Znote 6224W Intel T8300 Intel Chipset PM965 PC-5300 4gb Nvidia 8600M GT Zepto's rebranded bios: Phoenix Technologies LTD Z14ND06 - Date: 12/20/2007 Harddrive: 320 GB 5400 RPM which I replaced with a Kingston SSDnow 40 GB. No luck either. I haven't tried Windows Vista on the machine though, but I would like to keep Windows 7.

  Read the article

• How to compare old CPU to new CPU?

  - by Lasse V. Karlsen

  I hope this question doesn't get closed at once :) I have an old laptop, a Compaq NC4200, which is going its final laps around the track these days. Battery is dead, and everything kinda runs slow. It also has only 1GB of memory, and even though I don't know if it can take more, I probably wouldn't be able to get hold of any that matches without having to special order it. The size, however, has been ideal for my usage pattern, so I'm looking to replace it with a similarly sized laptop, at least in the same size category. However, it's been a while since I tried keeping track of CPUs, so I have a question. The old laptop has a Intel Pentium M 760 1.86GHz processor. One laptop I found online has a Intel Pentium SU4100 1.3GHz dual-core. This type of processor seems to be quite common in the price and size-range I've been looking. What kind of relative performance boost could I expect from the old one to the new one? I am not expecting a "about 7.45x speed", but some indication would be nice. For instance, dual-core tells me it might be akin to 2.6GHz, but I assume I can't simply compare 1.86GHz to 2.6GHz and expect the new one to run about 1.4x as fast, I expect more these days. Or is that unrealistic for this kind of processor? Do I need to up my price range and go for a 2+ GHz processor?

  Read the article

• Fedora 9 not reconizing hard drive

  - by Andrew Jones

  I am installing Fedora 9 to a PC (specifications at the bottom) and have had a lot of trouble with it recognising the hard drive. To get the Fedora installer to recognize it in the first place I had to pass "ata_generic.all_generic_ide=1 pci=nomsi" to the kernel, after which it installed OK. However, now when I boot the installed OS, I get a "could not find filesystem '/dev/root'" error. I tried passing the same arguments to the kernel at boot as I did when installing but to no avail. I have tried using the default LVM layout and defining manual ones but it made no difference. There is no option in the BIOS to enable AHCI or anything like that, in fact the BIOS is very limited in most respects. I can get into the system by using the installation CD in rescue mode (with those extra kernal parameters) but I'm not sure what to do once in there... Unfortunately using a more recent version of Fedora or even another Linux distribution altogether isn't an option becuase of outside constraints - which is annoying since I know for a fact Ubuntu works fine on this setup. I have not been using Linux that long, so treat me like an idiot - I am one. Any help would be greatly appreciated, thanks! System spec: Intel Atom Z530 CPU @ 1.6 GHz Intel US15W chipset 1 GB DDR2 160 GB SATA harddisk (Samsung HM16HI) 1000 Mbit/s Ethernet port Phoenix BIOS

  Read the article

• Enabling AHCI in BIOS for SSD

  - by Robert

  I am trying to help a friend with a desktop upgrade. It is an old machine with an Intel DG31 main board. The board has 1 IDE port to which a DVD-ROM drive is connected, and 2 SATA ports. 1 SATA port had a hard drive with XP on it. I have made that the secondary drive now and wiped the OS as requested, so it is just for data. The new SSD has been installed but I read that for best results one must enable AHCI in the BIOS? So I checked and in the BIOS there is a SATA Mode setting with 2 options - Native and Legacy. I think Native means AHCI? After setting to Native, I installed Windows 7 Home Premium and all the latest drivers from Intel's website and all Windows Updates. Now when I check Device Manager I see this: Also Microsoft says HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci\Start and HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\IastorV\Start should have value 0 for AHCI but I see that the value is 3 for both. So does this mean that Native mode is not AHCI? Or Windows 7 ignored BIOS setting and installed in IDE mode, maybe because both cables are present? Please help me enable AHCI on this system. Thanks!

  Read the article

• New XPC: No video, no ethernet link, but drive spins

  - by Mike Pennington

  I bought a Shuttle XPC SH67H3 with integrated video. I installed: An Intel i5 2450P 16GB DDR3 RAM A SATA hard drive from my old linux server that still is bootable I have both power connectors plugged into the motherboard. I realize that the Intel i5-2450P doesn't have video capabilities; however, the drive spins like it's doing something useful. It seems like I should get an ethernet link light when I fire this up. I plan to run this headless anyway, so it would be really nice if I could figure out how to run this without a video card at all. I know the IP address and login info for the linux install on the disk. I plugged in speakers, but get no bios beeps when I power it up. Shuttle's bios manual has nothing in there that indicates I should have problems in this configuration. My questions: Is there a reason that the missing video card would block usage of the ethernet port? Are there settings on the motherboard / bios I can change to get this working?

  Read the article

• Huge or minimal performance hit running game servers on a Virtual Machine? [closed]

  - by Damainman

  I have a two dedicated servers to choose from depending on which one would do a better job. I plan on updating the Hard Drive space and RAM at a later date depending on how I move forward. Server 1: 500GB Hard Drive 8GB RAM 2x 64bit Intel Xeon L5420(Quad Core) @ 2.50Ghz Server2: 500GB Hard Drive 8GB RAM 2x 64bit Intel Xeon E5420(Quad Core) @ 2.50GHz I want to run a virtual machine that will host about 10 game servers, with about 16 active slots per server. It will be a mix and match from: Minecraft Counter Strike( 1.6, Source, Global Offensive) Battlefield Team Fortress I know the general consensus is virtualization is a horrible idea if you plan on running virtual servers on them. The issue is, the discussions I read do not really clearly state whether they are speaking about a virtual server running inside an OS(ie: VMware Player running on Windows with the game server in a VM) or a Hypervisor such as Xen Cloud Platform. I am trying to get a definite answer on how feasible the above would be and how much of a performance hit it might be if the VM running the game servers is on a hypervisor such as Xen Cloud Platform. My initial research lead me to believe that there wouldn't be a performance hit since the virtualization is different than running it via inside of a OS.

  Read the article

• Laptop will not boot

  - by WillumMaguire

  This is a dell studio 1558 laptop. Now, something is wrong with the charger that it won't charge the laptop, but the laptop can turn on and operate properly as long as it is attached. It has been like this for a while, but it's not the problem. My problem is that as of yesterday, It takes several minutes to get past the "dell" startup logo (where is says "f2 setup" and "f12 boot options"). After it gets past, it beeps as normal to tell me about the charger and gives me the f2/f12 options and f1 to continue as normal. I can press f12 to get into boot options and load into my live USB BackTrack 5 ISO, but after "startx" it just stays at a black screen. I can also access BIOS setup, but see nothing that would help the problem. When I boot to the HDD, it gives me this Intel UNDI, PXE-2.1 (build 083) Realktek PCIe GBE Family Controller Series V.2.29 (06/30/09) PXE-E61: Media test failure, check cable PXE-M0F: Exiting PXE ROM Operating System not found Also, pressing f8 gives me the same results as booting as normal. It is running Windows 7 Ultimate, dual-core Intel i3 @ 2.27ghz and 4gb RAM. I think there is an issue with the HDD, as the "Operating System not found" would lead me to believe. Is this a fixable problem?

  Read the article

• SQL Server Installation: Is it 32 or 64 bit?

  - by CapBBeard

  Recently I was performing an OS upgrade on one of our DB servers, moving from Server 2003 to Server 2008. The DBMS is SQL Server 2005. While reinstalling SQL on the new Windows installation, I went to another of our DB servers to verify a couple of settings. Now, I always thought this second server was Server 2003 x64 + SQL 2005 x64 (from what I'd been told), but I now have my doubts about this. I now suspect that it is in fact only 32 bit SQL, however I'd like to verify this. Here's some details: The OS is definitely 64 bit. xp_msver shows Platform as NT INTEL X86 SELECT @@VERSION shows Microsoft SQL Server 2005 - 9.00.4035.00 (Intel X86)... However sqlservr.exe is not shown with '* 32' in taskmgr, does anyone know why this is the case, if it is in fact 32 bit as claimed? Despite this, it does seem to be running out of the x86 program files folder. If I do the same checks on a confirmed 64 bit installation, it does give back the expected 64 bit readings, which can only prove that this server in question is only running in 32 bit. Now, that being the case, the question arises about how much memory this '32 bit' install can use. Task manager reports about 3.5GB memory usage for sqlservr.exe (The server has 16GB physical). I suspect that AWE has not been configured at all, and therefore the server will be significantly under-utilised (remembering that the OS is 64 bit) if SQL is simply using a 32bit address space. Is this assumption correct? I feel the server should have SQL reinstalled as 64 bit in order to fully utilise the hardware platform, however it is currently heavily in production; this will be no easy task. I suspect we may just have to configure AWE correctly and let it be for the time being (Unless this is a bad idea?). I apologise that this question is a little vague/lost; I'm no SQL expert, just trying to get a handle on what's going on here.

  Read the article

• Will just a couple of thermal "trip" shutdowns typically damage a CPU?

  - by T.J. Crowder

  The short version If a CPU gets so hot that the system turns itself off because of a thermal trip signal just a couple of times, is it likely that the CPU will be damaged? Or does the trip do its job, turning it off before the CPU gets damaged? (This is with all default settings in the BIOS; I haven't raised any temp thresholds or overclocked anything.) The longer version I just got this Intel Atom D510-based fanless system, installed a 2.5" mobile SATA drive and two 2GB PC2-6400s, closed it up, and having checked everything was recognized in the BIOS, set about installing Ubuntu. After a couple of false starts related, I think, to the external DVD drive I was using, I got the install happily running along. About three-fourths or so of the way through the install, having been running less than an hour, the machine turned itself off. I was actually out of the room at the time, but when I came back and turned it back on, it said it had shut down due to a thermal event. I went into the BIOS and saw that (at that point, having just been turned back on after a couple of minutes off), it was running 87C. As near as I can tell from Intel's docs (PDF here), the max "junction" temperature for the CPU is 100C and it will raise a THERMTRIP signal at 125C. Yowsa. Presumably there will be some back-and-forth with the vendor on this, I'm just wondering whether letting it get that hot a couple of times is likely to end up damaging it.

  Read the article

• Can I have damaged a CPU ?

  - by Pascal

  Hey guys, This is a question I asked on Anantech forums, but I just discovered this community and think this question would fit right in. Here goes: I built a PC around a Q9550 1 1/2 years ago (MoBo is an Asus P5Q deluxe). Specs give 2.83GHz, OC'ed it to 3.40 GHZ without any problem (or so I thought) till 2 months ago. Cooling is provided by stock Intel Fan... 2 Months ago, I began to see random crashes, bios saying CPU overheat error... PC would reboot at OC'ed speed without any problem. Since last saturday and a few more crashes, PC won't reboot at 3.40 GHz, and even at stock speed (2.83 GHz), I got core temperatures of (60 C idle, 95 C under load) on the first two cores. This is the 4 core temperatures I am talking about, not the T-CPU which obvioulsy is lower. Fan is running at a steady 2000 RPM. Questions for you : 1. Is 2000 RPM the normal speed of the Intel fan or is my fan somehow broken (which could explain the overheating). In this case, any recommendation for a good fan for OCing ? 2. Hypothesis I fear is the right one: can the CPU have been slowly damaged over time by this OCing, meaning there is nothing much to do except waiting for it to die ? (As a side note, I am surprised that the 9550 is still around 300 $CDN here... Thought it would have been cheaper with all those i3/i5/i7 around). Any help or advice would be more than welcome...

  Read the article

• AMD 700, 800 series chipset. I'm lost.

  - by Shiki

  I've been an Intel / NVidia user ever since I started using computers. Intel really gone up with the prices, and they won't get cheaper. So I decided to get an AMD. But WHICH one? I mean.. not shopping question but.. what are the differences? Like: 880GMA comes only with a single PCI ex and it looks like a chinese replica (no offense). While 890FX comes with 5PCI-ex for QuadCrossfire. Also.. what's the deal with 7xx series? I mean.. its the same price. Yet its older? Or why is it 7xx? Isn't there a single chipset between? Not chinese YET it's durable/fine for long-term usage? What it should know (desktop stuff): NVidia GPU (Zalman AMP2 GTX 260^2 (one card)) Phenom 1090T cpu A somewhat good audio. Any ideas which is the chipset I'm searching for? If this sounds too much of a shopping question, feel free to edit. I just want some clarification on these chipsets.

  Read the article

• SQL Server 2008 Web VS SQL Server 2008 Enterprise

  - by Jeremy

  I wrote an application a few months ago, and was hosting it out of our offices on a workstation with an Intel Core 2 Quad Q8200 @ 2.33GHz, 8 GB RAM, Windows Server 2008 Enterprise and SQL Server 2008 Enterprise. Both the webserver and database server were run on the same machine. We had a huge influx in traffic, and moved ClubUptime.com, and got 2 of their top teir windows VMs. The Database server runs Windows 2008 R2 Standard and SQL Server 2008 R2 Web on 8 GB ram and an Intel Xeon e5620 @ 2.40GHz. Ever since switching, the database which used to run at around 400MB in RAM now runs at around 4-7GB, and there haven't been any changes to it (other than a couple columns here and there). Our traffic has quadrupled, and our DB is 6 GB on disk, why would SQL server take up 7 GB if the DB is only 6. And why would it be storing the ENTIRE database in memory? Another thing is why growing 4 times in size did the database's memory footprint grow 12 times? Last question: Why does the CPU peg at 100% now where it didn't before? The design is simple, VERY few joins, NO subqueries. I am just at a loss, unless it is the SQL server edition, or the fact that I moved from real hardware to a VM.

  Read the article

• Reduce power consumption of gaming computer while idle

  - by White Phoenix

  This is my current build: EVGA X58 (first generation) motherboard Intel i7 965 clocked @ 3.3 Ghz 3x DDR3-1600 Corsair RAM at stock timings and voltages Corsair AX750 80 Plus Gold PSU 1 Optical Drive 1 Seagate 7200.10 500 GB drive 2x Western Digital Caviar Black 1 TB drives OCZ Vertex 1 60 GB EVGA GTX 460 oc'd at 800/1600/1850 Antec 1200 case HT-Omega Striker 7.1 Sound Card Windows 7 32-bit Professional (PAE Enabled) I've already seen this post Reduce power use on computer and this post How do I lower power consumption of my computer and while useful, I'm looking for answers specific to my build and OS. I'm pretty sure this build is a energy-intensive build by default, but I want to try to reduce the amount of energy my build uses when I leave it idle (when I go to bed or go out, etc). The first requirement for this machine is that I need to leave it on, so I cannot turn it off while it's being unused. I run it as a file server for personal reasons and I also leave it on in case people leave me messages on various IM services and chat clients (IRC, MSN, Steam, XFire, Pidgin, etc). I'm also unable to replace the parts in my computer with a cheaper "greener" part. What are some ways to minimize the amount of power the machine uses? I'm already using a high efficiency power supply (80 Plus Gold), but I imagine there's other things that can be done in the BIOS and Windows' power settings to reduce power usage while I'm not using the computer. From what I can tell, I can't use Sleep since that'll disable network access (whole reason why I leave the computer on in the first place). I already turn off my monitor when it's not in use. I enabled Intel SpeedStep within the BIOS (I know, I have a 965 and why am I enabling SpeedStep?) Should I bring the graphics card back to stock speeds and lower the clock on the processor even more? Main reason why I'm asking is I think this computer alone is the reason why my power bill is high, so I want to reduce its consumption to as low as possible without having to shut the thing down.

  Read the article

• Hosting websites in our Workplace custom-built datacentre

  - by i.h4d35

  I'm faced with unique learning opportunity at work at the moment. Due to the slowdown (amongst other reasons), the powers that be at my office have decided to abandon our shared hosting providers (both shared and dedicated hosting) and have decided to host the websites at our office's datacentre. We're running 7 websites, wherein the average unique hits per day at the moment is about 900. We have 2 servers set aside for this - one is a DELL POWER EDGE 1850 (Intel Xeon 3 GHZ*2, 4GB RAM, 73GB HDD and the other is an HP DL 380 G3 (Intel Xeon 2.8 GHz, 6 GB RAM, 73 GB HDD) a) I would like to know the pros and cons of going ahead with this project.All the sites will be hosted on a single IP. In all probability, the OS is going to be CentOS. b) Do you think I should consider Virtualization into this equation (KVM/Xen)? I was thinking in terms of separate instances of the DB server and the frontend though I do not know if this is the best way to go. c) Should I be trying to use cloud stacks like OpenStack and try to make it look like websites hosted on some sort of Public Cloud? (something that I checked out here). Here is something else I came across, which looks similar to what needs to be done at our office. About the websites - Of the 7 websites, 4 are basic static websites which basically gives a whole lot of information about a few local institutions. The remaining 3 are local product-based websites developed in PHP wherein end user can view products and order them online. I am trying to take this as a learning experience wherein I can learn to build something from scratch and save the company a little something in the process. The migration needs to be completed by Easter so I guess it gives us some time (or am I being overly optimistic??). I am confused here and would appreciate all the help I can get. Thanks in advance.

  Read the article

• What does "cpuid level" means ? Asking just for curiosity

  - by ogzylz

  For example, I put just 2 core info of a 16 core machine. What does "cpuid level : 6" line means? If u can provide info about lines "bogomips : 5992.10" and "clflush size : 64" I will be appreciated ------------- processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 6 model name : Intel(R) Xeon(TM) CPU 3.00GHz stepping : 8 cpu MHz : 2992.689 cache size : 4096 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 fpu : yes fpu_exception : yes cpuid level : 6 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl vmx cid cx16 xtpr lahf_lm bogomips : 5992.10 clflush size : 64 cache_alignment : 128 address sizes : 40 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 6 model name : Intel(R) Xeon(TM) CPU 3.00GHz stepping : 8 cpu MHz : 2992.689 cache size : 4096 KB physical id : 1 siblings : 4 core id : 0 cpu cores : 2 fpu : yes fpu_exception : yes cpuid level : 6 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl vmx cid cx16 xtpr lahf_lm bogomips : 5985.23 clflush size : 64 cache_alignment : 128 address sizes : 40 bits physical, 48 bits virtual power management:

  Read the article

• Windows 7 x64 wired connection problem. IP, gateway, dns assigned, can't ping. Network detected as "Network"

  - by Emil Lerch

  I am having a problem connecting to a specific wired network with my Latitude E6410 laptop. Other wired networks seem to work fine, but this one does not. I have a coworker with me with the same Intel 82577LM Gigabit Network card, and he can connect just fine. I've updated to the latest Intel drivers (11.8.75.0) and am not using Pro Set. I obtain all DHCP information just fine (IP, netmask, DNS server, default gateway). I cannot ping anything (internal or on the Internet - I tried pinging Google's public DNS servers by IP 8.8.8.8), nor can I get answers to any DNS queries through NS Lookup. Windows troubleshooting says everything is fine, but I can't get DNS responses. I've seen issues like this in the past that were related to link speed/duplex autonegotiaion failures, so I've tried manually setting link speed/duplex to all values one by one with no success. My coworker is using all default settings, so he is just using autonegotiate. Any ideas of other things to try?

  Read the article

• No headphone or speakers plugged in - Windows 7 issue

  - by Amit Ranjan

  I am facing a wierd issue between my sound card driver and Windows7(any edition). I have a sony vaio notebook (VPCEB24EN). Two days ago, on start I got diabled wifi, charging and speakers. Then I restart the PC and everthing worked fine. Later on I again restarted my machine, and then I found the my speakers were not working. I thought, restart will work. I restarted many more times but it did'nt work. I searched google and found that , it might be due to : 1. Hardware is not switched on from bios. 2. No hardware. 3. overriding 64-bit drivers with 32-bit drivers. To make it working, I restored my laptop from scratched, but while restoring pc, the realtek HD drivers, it gave me an error 505. I then formatted the drive and installed Win7 Ultimate 32bit (With PC was, Win7 64-bit Home Basic). I got lots of yellow exclamation in device manager, thinking now this will resolve my issue. But Even after the installing all drivers on a fresh installation, I was still with the same position. A red cross on speaker- No Speakers or Headphone plugged in. Please Note: My Laptop is Vaio , E Series, VPCEB24EN. Audio : Intel® High Definition Audio compatible but accepts Realted Audio. While using BIOS Agent, I got Intel Chipset 5 Series Audio Adapter and ATI RV370 Audio adapter found on my board. Installed is Win7 32bit Ultimate. factory default was Win7 64-bit Home Basic Memory: RAM 3GB/ 320GB HDD Display : ATI Mobility Radeon™ HD 5145 Graphics

  Read the article

• Why does my DSDT table is different from what I found online?

  - by Hao Shen

  I have found a field in DSDT table where I want to modify from here http://www.ztex.de/misc/c2ctl.e.html Generally, I want to modify the _PSS field about the processor so that I can have more frequency levels available in the CPUfreq driver interface. I try to use this command to dissemble the DSDT table from my Desktop(Linux2.6.29,Intel CORE 2): cat /proc/acpi/dsdt > dsdt.aml iasl -d dsdt.aml Then I have a file dsdt.dsl as following(very long, so I just show the beginning of the file): /* * Intel ACPI Component Architecture * AML Disassembler version 20090123 * * Disassembly of dsdt.aml, Mon May 6 20:41:40 2013 * * * Original Table Header: * Signature "DSDT" * Length 0x00003794 (14228) * Revision 0x01 **** ACPI 1.0, no 64-bit math support * Checksum 0x46 * OEM ID "DELL" * OEM Table ID "dt_ex" * OEM Revision 0x00001000 (4096) * Compiler ID "INTL" * Compiler Version 0x20050624 (537200164) */ DefinitionBlock ("dsdt.aml", "DSDT", 1, "DELL", "dt_ex", 0x00001000) { Method (DBIN, 0, NotSerialized) { Noop } Scope (\) { Device (_SB.VBTN) ................... But I can not find the _PSS field as shown in the website I have given above. I do not know why? I am sure the current cpufreq driver shows 4 frequency levels available. So at least there should be something in the table showing this..right? Has anybody here played with the DSDT table before? Thanks,

  Read the article

• Quad channel memory and compatibility

  - by balteo

  My motherboard has quad channel memory compatibility. There are 8 memory slots in all: 4 slots are black the other 4 slots are white. I currently have 4 memory modules of 1 GB each in the 4 white slots. That leaves me with 4 free memory slots. My question is: can I put 4 memory modules of 2 GB each in the 4 remaining slots or do I have to use modules of 1 GB all over? FYI here is the output of lshw: alpha description: Ordinateur Tour produit: Precision WorkStation 690 *-cpu:0 description: CPU produit: Intel(R) Xeon(R) CPU X5355 @ 2.66GHz *-memory description: Mémoire Système identifiant matériel: 1000 emplacement: Carte mère taille: 4GiB *-bank:0 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) produit: HYMP512F72CP8N3-Y5 fabriquant: Hynix Semiconductor (Hyundai Electronics) identifiant matériel: 0 numéro de série: 56737501 emplacement: DIMM 1 taille: 1GiB bits: 64 bits horloge: 667MHz (1.5ns) *-bank:1 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) produit: HYMP512F72CP8N3-Y5 fabriquant: Hynix Semiconductor (Hyundai Electronics) identifiant matériel: 1 numéro de série: 48115124 emplacement: DIMM 2 taille: 1GiB bits: 64 bits horloge: 667MHz (1.5ns) *-bank:2 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) produit: HYMP512F72CP8N3-Y5 fabriquant: Hynix Semiconductor (Hyundai Electronics) identifiant matériel: 2 numéro de série: 48115523 emplacement: DIMM 3 taille: 1GiB bits: 64 bits horloge: 667MHz (1.5ns) *-bank:3 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) produit: HYMP512F72CP8N3-Y5 fabriquant: Hynix Semiconductor (Hyundai Electronics) identifiant matériel: 3 numéro de série: 48115424 emplacement: DIMM 4 taille: 1GiB bits: 64 bits horloge: 667MHz (1.5ns) *-bank:4 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) [vide] fabriquant: FFFFFFFFFFFF identifiant matériel: 4 numéro de série: FFFFFFFF emplacement: DIMM 5 bits: 64 bits horloge: 667MHz (1.5ns) *-bank:5 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) [vide] fabriquant: FFFFFFFFFFFF identifiant matériel: 5 numéro de série: FFFFFFFF emplacement: DIMM 6 bits: 64 bits horloge: 667MHz (1.5ns) *-bank:6 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) [vide] fabriquant: FFFFFFFFFFFF identifiant matériel: 6 numéro de série: FFFFFFFF emplacement: DIMM 7 bits: 64 bits horloge: 667MHz (1.5ns) *-bank:7 description: FB-DIMM DDR2 FB-DIMM Synchrone 667 MHz (1,5 ns) [vide] fabriquant: FFFFFFFFFFFF identifiant matériel: 7 numéro de série: FFFFFFFF emplacement: DIMM 8 bits: 64 bits horloge: 667MHz (1.5ns) *-pci:0 description: Host bridge produit: 5000X Chipset Memory Controller Hub fabriquant: Intel Corporation identifiant matériel: 100 information bus: pci@0000:00:00.0 version: 12 bits: 32 bits horloge: 33MHz

  Read the article

• Desktop bigger than screen

  - by alex

  I am using MSI U115 11" netbook (OS: Windows XP Home, graphics card: Intel Graphics Media Accelerator 500) and today after I switched it on, desktop was bigger than screen. To be exact: screen resolution was set to the lowest possible and I could move mouse outside of screen (but only below - left, right and up worked normally, mouse could not exceed screen boundaries). I changed resolution back to normal, but the problem with desktop being bigger than screen remained (as before, only lower part - cannot see task bar, etc. When I hit windows button on keyboard, only upper part of menu start is visible). What I already tried was changing all kind of graphics and screen settings - none of them helped. I also tried to restore the system to few days before, but it didn't help neither. What can I do to make the desktop look "normally"? EDIT: Some additional info regarding screen: Sorry it's in polish - but let me explain. There are two screens I can choose (Monitor domyslny means default screen), but the second one (the default one) is not available. After I choose it and click apply number 1. is used (and as you can see it has only two resolutions available. There are more in the second one - but without 1024x600 though). The two ticked and grayed out options here are Use this screen as the main one and Enlarge Windows desktop to match this monitor's size. Too bad I cannot change them. When I choose the second screen, the first box is unchecked and grayed out. The second box is available to be changed but it doesn't matter anyway as after applying changes it reverts to the first screen anyway. EDIT: Intel Graphics Media Control Panel screenshot.

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >