Search Results

Search found 3790 results on 152 pages for 'jamie ide'.

Page 73/152 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• How to improve Samba performance on VirtualBox machine?

  - by ColinM

  I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

  Read the article

• Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

  - by Fazil

  I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

  Read the article

• KVM Virtual guest Paused on Reboot

  - by David Hamilton

  I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

  Read the article

• How to add addtional disks to a Windows 2008 KVM based Guest?

  - by taazaa

  I have a Win 2008 KVM based guest VM running on a Ubuntu 10 host. It is a raw image of 22G. I want to add a "data" drive which would show up as "D:\" drive on the guest. I first created a raw image using: qemu-img create -f raw ~/vmdisk2.img 50G Then, tried attaching it using virsh attach-disk. When that did not work, I tried editing the xml file of the VM directly. Both did not seem to work. I would greatly appreciate any help on how to do this and what the best practice is. I want to keep the base image small, so that I can clone it (hopefully) and then attach necessary storage based on the application at hand. Update: The xml of the vm before adding the second drive: <domain type='kvm'> <name>win08e-vm1</name> <uuid>183a4ba0-1c0b-0b04-ad01-aa7c3a4cb390</uuid> <memory>1048576</memory> <currentMemory>1048576</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='localtime'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/win08e-vm1.img'/> <target dev='hda' bus='ide'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/home/taazaa/iso/Win08ER264.iso'/> <target dev='hdc' bus='ide'/> <readonly/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:7f:a7:ae'/> <source bridge='br0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <input type='tablet' bus='usb'/> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' keymap='en-us'/> <video> <model type='vga' vram='9216' heads='1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </memballoon> </devices> </domain> Thanks!

  Read the article

• Visual Studio 2010 Extension Manager (and the new VS 2010 PowerCommands Extension)

  - by ScottGu

  This is the twenty-third in a series of blog posts I’m doing on the VS 2010 and .NET 4 release. Today’s blog post covers some of the extensibility improvements made in VS 2010 – as well as a cool new "PowerCommands for Visual Studio 2010” extension that Microsoft just released (and which can be downloaded and used for free). [In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu] Extensibility in VS 2010 VS 2010 provides a much richer extensibility model than previous releases.  Anyone can build extensions that add, customize, and light-up the Visual Studio 2010 IDE, Code Editors, Project System and associated Designers. VS 2010 Extensions can be created using the new MEF (Managed Extensibility Framework) which is built-into .NET 4.  You can learn more about how to create VS 2010 extensions from this this blog post from the Visual Studio Team Blog. VS 2010 Extension Manager Developers building extensions can distribute them on their own (via their own web-sites or by selling them).  Visual Studio 2010 also now includes a built-in “Extension Manager” within the IDE that makes it much easier for developers to find, download, and enable extensions online.  You can launch the “Extension Manager” by selecting the Tools->Extension Manager menu option: This loads an “Extension Manager” dialog which accesses an “online gallery” at Microsoft, and then populates a list of available extensions that you can optionally download and enable within your copy of Visual Studio: There are already hundreds of cool extensions populated within the online gallery.  You can browse them by category (use the tree-view on the top-left to filter them).  Clicking “download” on any of the extensions will download, install, and enable it. PowerCommands for Visual Studio 2010 This weekend Microsoft released the free PowerCommands for Visual Studio 2010 extension to the online gallery.  You can learn more about it here, and download and install it via the “Extension Manager” above (search for PowerCommands to find it). The PowerCommands download adds dozens of useful commands to Visual Studio 2010.  Below is a screen-shot of just a few of the useful commands that it adds to the Solution Explorer context menus: Below is a list of all the commands included with this weekend’s PowerCommands for Visual Studio 2010 release: Enable/Disable PowerCommands in Options dialog This feature allows you to select which commands to enable in the Visual Studio IDE. Point to the Tools menu, then click Options. Expand the PowerCommands options, then click Commands. Check the commands you would like to enable. Note: All power commands are initially defaulted Enabled. Format document on save / Remove and Sort Usings on save The Format document on save option formats the tabs, spaces, and so on of the document being saved. It is equivalent to pointing to the Edit menu, clicking Advanced, and then clicking Format Document. The Remove and sort usings option removes unused using statements and sorts the remaining using statements in the document being saved. Note: The Remove and sort usings option is only available for C# documents. Format document on save and Remove and sort usings both are initially defaulted OFF. Clear All Panes This command clears all output panes. It can be executed from the button on the toolbar of the Output window. Copy Path This command copies the full path of the currently selected item to the clipboard. It can be executed by right-clicking one of these nodes in the Solution Explorer: The solution node; A project node; Any project item node; Any folder. Email CodeSnippet To email the lines of text you select in the code editor, right-click anywhere in the editor and then click Email CodeSnippet. Insert Guid Attribute This command adds a Guid attribute to a selected class. From the code editor, right-click anywhere within the class definition, then click Insert Guid Attribute. Show All Files This command shows the hidden files in all projects displayed in the Solution Explorer when the solution node is selected. It enhances the Show All Files button, which normally shows only the hidden files in the selected project node. Undo Close This command reopens a closed document , returning the cursor to its last position. To reopen the most recently closed document, point to the Edit menu, then click Undo Close. Alternately, you can use the CtrlShiftZ shortcut. To reopen any other recently closed document, point to the View menu, click Other Windows, and then click Undo Close Window. The Undo Close window appears, typically next to the Output window. Double-click any document in the list to reopen it. Collapse Projects This command collapses a project or projects in the Solution Explorer starting from the root selected node. Collapsing a project can increase the readability of the solution. This command can be executed from three different places: solution, solution folders and project nodes respectively. Copy Class This command copies a selected class entire content to the clipboard, renaming the class. This command is normally followed by a Paste Class command, which renames the class to avoid a compilation error. It can be executed from a single project item or a project item with dependent sub items. Paste Class This command pastes a class entire content from the clipboard, renaming the class to avoid a compilation error. This command is normally preceded by a Copy Class command. It can be executed from a project or folder node. Copy References This command copies a reference or set of references to the clipboard. It can be executed from the references node, a single reference node or set of reference nodes. Paste References This command pastes a reference or set of references from the clipboard. It can be executed from different places depending on the type of project. For CSharp projects it can be executed from the references node. For Visual Basic and Website projects it can be executed from the project node. Copy As Project Reference This command copies a project as a project reference to the clipboard. It can be executed from a project node. Edit Project File This command opens the MSBuild project file for a selected project inside Visual Studio. It combines the existing Unload Project and Edit Project commands. Open Containing Folder This command opens a Windows Explorer window pointing to the physical path of a selected item. It can be executed from a project item node Open Command Prompt This command opens a Visual Studio command prompt pointing to the physical path of a selected item. It can be executed from four different places: solution, project, folder and project item nodes respectively. Unload Projects This command unloads all projects in a solution. This can be useful in MSBuild scenarios when multiple projects are being edited. This command can be executed from the solution node. Reload Projects This command reloads all unloaded projects in a solution. It can be executed from the solution node. Remove and Sort Usings This command removes and sort using statements for all classes given a project. It is useful, for example, in removing or organizing the using statements generated by a wizard. This command can be executed from a solution node or a single project node. Extract Constant This command creates a constant definition statement for a selected text. Extracting a constant effectively names a literal value, which can improve readability. This command can be executed from the code editor by right-clicking selected text. Clear Recent File List This command clears the Visual Studio recent file list. The Clear Recent File List command brings up a Clear File dialog which allows any or all recent files to be selected. Clear Recent Project List This command clears the Visual Studio recent project list. The Clear Recent Project List command brings up a Clear File dialog which allows any or all recent projects to be selected. Transform Templates This command executes a custom tool with associated text templates items. It can be executed from a DSL project node or a DSL folder node. Close All This command closes all documents. It can be executed from a document tab. How to temporarily disable extensions Extensions provide a great way to make Visual Studio even more powerful, and can help improve your overall productivity.  One thing to keep in mind, though, is that extensions run within the Visual Studio process (DevEnv.exe) and so a bug within an extension can impact both the stability and performance of Visual Studio.  If you ever run into a situation where things seem slower than they should, or if you crash repeatedly, please temporarily disable any installed extensions and see if that fixes the problem.  You can do this for extensions that were installed via the online gallery by re-running the extension manager (using the Tools->Extension Manager menu option) and by selecting the “Installed Extensions” node on the top-left of the dialog – and then by clicking “Disable” on any of the extensions within your installed list: Hope this helps, Scott

  Read the article

• Visual Studio 2010 Productivity Tips and Tricks-Part 2: Key Shortcuts

  - by ToStringTheory

  Ask anyone that knows me, and they will confirm that I hate the mouse.  This isn’t because I deny affection to objects that don’t look like their mammalian-named self, but rather for a much more simple and not-insane reason: I have terrible eyesight.  Introduction Thanks to a degenerative eye disease known as Choroideremia, I have learned to rely more on the keyboard which I can feel digital/static positions of keys relative to my fingers, than the much more analog/random position of the mouse.  Now, I would like to share some of the keyboard shortcuts with you now, as I believe that they not only increase my productivity, but yours as well once you know them (if you don’t already of course)...  I share one of my biggest tips for productivity in the conclusion at the end. Visual Studio Key Shortcuts Global Editor Shortcuts These are shortcuts that are available from almost any application running in Windows, however are many times forgotten. Shortcut Action Visual Studio 2010 Functionality Ctrl + X Cut This shortcut works without a selection. If nothing is selected, the entire line that the caret is on is cut from the editor. Ctrl + C Copy This shortcut works without a selection. If nothing is selected, the entire line that the caret is on is copied from the editor. Ctrl + V Paste If you copied an entire line by the method above, the data is pasted in the line above the current caret line. Ctrl + Shift + V Next Clipboard Element Cut/Copy multiple things, and then hit this combo repeatedly to switch to the next clipboard item when pasting. Ctrl + Backspace Delete Previous Will delete the previous word from the editor directly before the caret. If anything is selected, will just delete that. Ctrl + Del Delete Next Word Will delete the next word/space from the editor directly after the caret. If anything is selected, will just delete that. Shift + Del Delete Focused Line Will delete the line from the editor that the caret is on. If something is selected, will just delete that. Ctrl + ? or Ctrl + ? Left/Right by Word This will move the caret left or right by word or special character boundary. Holding Shift will also select the word. Ctrl + F Quick Find Either the Quick Find panel, or the search bar if you have the Productivity Power Tools installed. Ctrl + Shift + F Find in Solution Opens up the 'Find in Files' window, allowing you to search your solution, as well as using regex for pattern matching. F2 Rename File... While not debugging, selecting a file in the solution explorer\navigator and pressing F2 allows you to rename the selected file. Global Application Shortcuts These are shortcuts that are available from almost any application running in Windows, however are many times forgotten... Again... Shortcut Action Visual Studio 2010 Functionality Ctrl + N New File dialog Opens up the 'New File' dialog to add a new file to the current directory in the Solution\Project. Ctrl + O Open File dialog Opens up the 'Open File' dialog to open a file in the editor, not necessarily in the solution. Ctrl + S Save File dialog Saves the currently focused editor tab back to your HDD/SSD. Ctrl + Shift + S Save All... Quickly save all open/edited documents back to your disk. Ctrl + Tab Switch Panel\Tab Tapping this combo switches between tabs quickly. Holding down Ctrl when hitting tab will bring up a chooser window. Building Shortcuts These are shortcuts that are focused on building and running a solution. These are not usable when the IDE is in Debug mode, as the shortcut changes by context. Shortcut Action Visual Studio 2010 Functionality Ctrl + Shift + B Build Solution Starts a build process on the solution according to the current build configuration manager settings. Ctrl + Break Cancel a Building Solution Will cancel a build operation currently in progress. Good for long running builds when you think of one last change. F5 Start Debugging Will build the solution if needed and launch debugging according to the current configuration manager settings. Ctrl + F5 Start Without Debugger Will build the solution if needed and launch the startup project without attaching a debugger. Debugging Shortcuts These are shortcuts that are used when debugging a solution. Shortcut Action Visual Studio 2010 Functionality F5 Continue Execution Continues execution of code until the next breakpoint. Ctrl + Alt + Break Pause Execution Pauses the program execution. Shift + F5 Stop Debugging Stops the current debugging session. NOTE: Web apps will still continue processing after stopping the debugger. Keep this in mind if working on code such as credit card processing. Ctrl + Shift + F5 Restart Debugging Stops the current debugging session and restarts the debugging session from the beginning. F9 Place Breakpoint Toggles/Places a breakpoint in the editor on the current line. Set a breakpoint in condensed code by highlighting the statement first. F10 Step Over Statement When debugging, executes all code in methods/properties on the current line until the next line. F11 Step Into Statement When debugging, steps into a method call so you can walk through the code executed there (if available). Ctrl + Alt + I Immediate Window Open the Immediate Window to execute commands when execution is paused. Navigation Shortcuts These are shortcuts that are used for navigating in the IDE or editor panel. Shortcut Action Visual Studio 2010 Functionality F4 Properties Panel Opens the properties panel for the selected item in the editor/designer/solution navigator (context driven). F12 Go to Definition Press F12 with the caret on a member to navigate to its declaration. With the Productivity tools, Ctrl + Click works too. Ctrl + K Ctrl + T View Call Hierarchy View the call hierarchy of the member the caret is on. Great for going through n-tier solutions and interface implementations! Ctrl + Alt + B Breakpoint Window View the breakpoint window to manage breakpoints and their advanced options. Allows easy toggling of breakpoints. Ctrl + Alt + L Solution Navigator Open the solution explorer panel. Ctrl + Alt + O Output Window View the output window to see build\general output from Visual Studio. Ctrl + Alt + Enter Live Web Preview Only available with the Web Essential plugin. Launches the auto-updating Preview panel. Testing Shortcuts These are shortcuts that are used for running tests in the IDE. Please note, Visual Studio 2010 is all about context. If your caret is within a test method when you use one of these combinations, the combination will apply to that test. If your caret is within a test class, it will apply to that class. If the caret is outside of a test class, it will apply to all tests. Shortcut Action Visual Studio 2010 Functionality Ctrl + R T Run Test(s) Run all tests in the current context without a debugger attached. Breakpoints will not be stopped on. Ctrl + R Ctrl + T Run Test(s) (Debug) Run all tests in the current context with a debugger attached. This allows you to use breakpoints. Substitute A for T from the preceding combos to run/debug ALL tests in the current context. Substitute Y for T from the preceding combos to run/debug ALL impacted/covering tests for a method in the current context. Advanced Editor Shortcuts These are shortcuts that are used for more advanced editing in the editor window. Shortcut Action Visual Studio 2010 Functionality Shift + Alt + ? Shift + Alt + ? Multiline caret up/down Use this combo to edit multiple lines at once. Not too many uses for it, but once in a blue moon one comes along. Ctrl + Alt + Enter Insert Line Above Inserts a blank line above the line the caret is currently on. No need to be at end or start of line, so no cutting off words/code. Ctrl + K Ctrl + C Comment Selection Comments the current selection out of compilation. Ctrl + K Ctrl + U Uncomment Selection Uncomments the current selection into compilation. Ctrl + K Ctrl + D Format Document Automatically formats the document into a structured layout. Lines up nodes or code into columns intelligently. Alt + ? Alt + ? Code line up/down *Use this combo to move a line of code up or down quickly. Great for small rearrangements of code. *Requires the Productivity Power pack from Microsoft. Conclusion This list is by no means meant to be exhaustive, but these are the shortcuts I use regularly every hour/minute of the day. There are still 100s more in Visual Studio that you can discover through the configuration window, or by tooltips. Something that I started doing months ago seems to have interest in my office.. In my last post, I talked about how I hated a cluttered UI. One of the ways that I aimed to resolve that was by systematically cleaning up the toolbars week by week. First day, I removed ALL icons that I already knew shortcuts to, or would never use them (Undo in a toolbar?!). Then, every week from that point on, I make it a point to remove an icon/two from the toolbar and make an effort to remember its key combination. I gain extra space in the toolbar area, AND become more productive at the same time! I hope that you found this article interesting or at least somewhat informative.. Maybe a shortcut or two you didn't know. I know some of them seem trivial, but I often see people going to the edit menu for Copy/Paste... Thought a refresher might be helpful!

  Read the article

• WPA2 authentication fails on Ubuntu 12.04 using Rosewill RNX-N1

  - by user94156

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. RNX-X1 works on other systems (including TV); also have 2 of 'em and tried each. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• WPA2 authentication fails using USB network devices (Linksys and Rosewill)

  - by Greg Youtz

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. Tried the same with a Linksys USB network adapter. Both failed to authenticate. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no Would appreciate insight on how to chase this down.

  Read the article

• How is WPF Data Binding using Object Data Source in Visual Studio 2010 done?

  - by Rob Perkins

  This is probably mostly a question about how to use the VS 2010 IDE tools in a way the Microsofties didn't specifically intend. But since this is something I immediately tried without success. I have defined a .NET 4.0 WPF Application project with a simple class that looks like this: Public Class Class1 Public Property One As String = "OneString" Public Property Two As String = "TwoString" End Class I then defined it as an "Object Data Source" in VS2010, using the IDE's "Add New Data Source..." feature. This exposes the class members in a GUI element in the IDE as given in this image: Dragging "Class1" from that tool to the surface of "Window1.xaml" in a default "WPF Application" results in the design view looking like this: And generated XAML like this: <Window x:Class="Window1" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="Window1" Height="133" Width="170" xmlns:my="clr-namespace:WpfApplication1" mc:Ignorable="d" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" > <Window.Resources> <CollectionViewSource x:Key="Class1ViewSource" d:DesignSource="{d:DesignInstance my:Class1, CreateList=True}" /> </Window.Resources> <Grid DataContext="{StaticResource Class1ViewSource}" HorizontalAlignment="Left" Name="Grid1" VerticalAlignment="Top"> <Grid.ColumnDefinitions> <ColumnDefinition Width="Auto" /> <ColumnDefinition Width="Auto" /> </Grid.ColumnDefinitions> <Grid.RowDefinitions> <RowDefinition Height="Auto" /> <RowDefinition Height="Auto" /> </Grid.RowDefinitions> <Label Content="One:" Grid.Column="0" Grid.Row="0" HorizontalAlignment="Left" Margin="3" VerticalAlignment="Center" /> <TextBlock Grid.Column="1" Grid.Row="0" Height="23" HorizontalAlignment="Left" Margin="3" Name="OneTextBlock" Text="{Binding Path=One}" VerticalAlignment="Center" /> <Label Content="Two:" Grid.Column="0" Grid.Row="1" HorizontalAlignment="Left" Margin="3" VerticalAlignment="Center" /> <TextBlock Grid.Column="1" Grid.Row="1" Height="23" HorizontalAlignment="Left" Margin="3" Name="TwoTextBlock" Text="{Binding Path=Two}" VerticalAlignment="Center" /> </Grid> Note the data bindings Text="{Binding Path=One}" and Text="{Binding Path=Two}" in the TextBlock elements. Code-behind for Window1.xaml has this in Window_Loaded: Class Window1 Private m_c1 As New Class1 Private Sub Window1_Loaded(ByVal sender As Object, ByVal e As System.Windows.RoutedEventArgs) Handles Me.Loaded Dim Class1ViewSource As System.Windows.Data.CollectionViewSource = CType(Me.FindResource("Class1ViewSource"), System.Windows.Data.CollectionViewSource) 'Load data by setting the CollectionViewSource.Source property: 'Class1ViewSource.Source = [generic data source] Me.DataContext = m_c1 End Sub End Class Running the application produces this output: The expected result was that "OneString" would appear next to "One" and "TwoString" next to "Two" in the running window. The question is: Why didn't this work? What will work instead? If I put bindings in a DataTemplate, it works. Blend, with its sample data stuff, implied that this should work, but it doesn't. I know I'm missing something pretty fundamental here; what is it?

  Read the article

• Help to argue why to develop software on a physical computer rather than via a remote desktop

  - by s5804

  Remote desktops are great and many times a blessing and cost effective (instead of leasing expensive cables). I am not arguing against remote desktops, just if one have the alternative to use either remote desktop or physical computer, I would choose the later. Also note that I am not arguing for or against remote work practices. But in my case I am required to be physically present in the office when developing software. Background, I work in a company which main business is not to develop software. Therefore the company IT policies are mainly focused on security and to efficiently deploying/maintaing thousands of computer to users. Further, the typical employee runs typical Office applications, like a word processors. Because safety/stability is such a big priority, every non production system/application, shall be deployed into a physical different network, called the test network. Software development of course also belongs in the test network. To access the test network the company has created a standard policy, which dictates that access to the test network shall go only via a remote desktop client. Practically from ones production computer one would open up a remote desktop client to a virtual computer located in the test network. On the virtual computer's remote desktop one would be able to access/run/install all development tools, like Eclipse IDE. Another solution would be to have a dedicated physical computer, which is physically only connected to the test network. Both solutions are available in the company. I have tested both approaches and found running Eclipse IDE, SQL developer, in the remote desktop client to be sluggish (keyboard strokes are delayed), commands like alt-tab takes me out of the remote client, enjoying... Further, screen resolution and colors are different, just to mention a few. Therefore there is nothing technical wrong with the remote client, just not optimal and frankly de-motivating. Now with the new policies put in place, plans are to remove the physical computers connected to the test network. I am looking for help to argue for why software developers shall have a dedicated physical software development computer, to be productive and cost effective. Remember that we are physically in office. Further one can notice that we are talking about approx. 50 computers out of 2000 employees. Therefore the extra budget is relatively small. This is more about policy than cost. Please note that there are lots of similar setups in other companies that work great due to a perfectly tuned systems. However, in my case it is sluggish and it would cost more money to trouble shoot the performance and fine tune it rather than to have a few physical computers. As a business case we have argued that productivity will go down by 25%, however it's my feeling that the reality is probably closer to 50%. This business case isn't really accepted and I find it very difficult to defend it to managers that has never ever used a rich IDE in their life, never mind developed software. Further the test network and remote client has no guaranteed service level, therefore it is down for a few hours per month with the lowest priority on the fix list. Help is appreciated.

  Read the article

• Looking into Enum Support in Entity Framework 5.0 Code First

  - by nikolaosk

  In this post I will show you with a hands-on demo the enum support that is available in Visual Studio 2012, .Net Framework 4.5 and Entity Framework 5.0. You can have a look at this post to learn about the support of multilple diagrams per model that exists in Entity Framework 5.0. We will demonstrate this with a step by step example. I will use Visual Studio 2012 Ultimate. You can also use Visual Studio 2012 Express Edition. Before I move on to the actual demo I must say that in EF 5.0 an enumeration can have the following types. Byte Int16 Int32 Int64 Sbyte Obviously I cannot go into much detail on what EF is and what it does. I will give again a short introduction.The .Net framework provides support for Object Relational Mapping through EF. So EF is a an ORM tool and it is now the main data access technology that microsoft works on. I use it quite extensively in my projects. Through EF we have many things out of the box provided for us. We have the automatic generation of SQL code.It maps relational data to strongly types objects.All the changes made to the objects in the memory are persisted in a transactional way back to the data store. You can find in this post an example on how to use the Entity Framework to retrieve data from an SQL Server Database using the "Database/Schema First" approach. In this approach we make all the changes at the database level and then we update the model with those changes. In this post you can see an example on how to use the "Model First" approach when working with ASP.Net and the Entity Framework. This model was firstly introduced in EF version 4.0 and we could start with a blank model and then create a database from that model.When we made changes to the model , we could recreate the database from the new model. You can search in my blog, because I have posted many posts regarding ASP.Net and EF. I assume you have a working knowledge of C# and know a few things about EF. The Code First approach is the more code-centric than the other two. Basically we write POCO classes and then we persist to a database using something called DBContext. Code First relies on DbContext. We create 2,3 classes (e.g Person,Product) with properties and then these classes interact with the DbContext class. We can create a new database based upon our POCOS classes and have tables generated from those classes.We do not have an .edmx file in this approach.By using this approach we can write much easier unit tests. DbContext is a new context class and is smaller,lightweight wrapper for the main context class which is ObjectContext (Schema First and Model First). Let's begin building our sample application. 1) Launch Visual Studio. Create an ASP.Net Empty Web application. Choose an appropriate name for your application. 2) Add a web form, default.aspx page to the application. 3) Now we need to make sure the Entity Framework is included in our project. Go to Solution Explorer, right-click on the project name.Then select Manage NuGet Packages...In the Manage NuGet Packages dialog, select the Online tab and choose the EntityFramework package.Finally click Install. Have a look at the picture below   4) Create a new folder. Name it CodeFirst . 5) Add a new item in your application, a class file. Name it Footballer.cs. This is going to be a simple POCO class.Place it in the CodeFirst folder. The code follows public class Footballer { public int FootballerID { get; set; } public string FirstName { get; set; } public string LastName { get; set; } public double Weight { get; set; } public double Height { get; set; } public DateTime JoinedTheClub { get; set; } public int Age { get; set; } public List<Training> Trainings { get; set; } public FootballPositions Positions { get; set; } }    Now I am going to define my enum values in the same class file, Footballer.cs    public enum FootballPositions    {        Defender,        Midfielder,        Striker    } 6) Now we need to create the Training class. Add a new class to your application and place it in the CodeFirst folder.The code for the class follows.     public class Training     {         public int TrainingID { get; set; }         public int TrainingDuration { get; set; }         public string TrainingLocation { get; set; }     }   7) Then we need to create a context class that inherits from DbContext.Add a new class to the CodeFirst folder.Name it FootballerDBContext.Now that we have the entity classes created, we must let the model know.I will have to use the DbSet<T> property.The code for this class follows       public class FootballerDBContext:DbContext     {         public DbSet<Footballer> Footballers { get; set; }         public DbSet<Training> Trainings { get; set; }     } Do not forget to add  (using System.Data.Entity;) in the beginning of the class file 8) We must take care of the connection string. It is very easy to create one in the web.config.It does not matter that we do not have a database yet.When we run the DbContext and query against it,it will use a connection string in the web.config and will create the database based on the classes. In my case the connection string inside the web.config, looks like this      <connectionStrings>    <add name="CodeFirstDBContext"  connectionString="server=.\SqlExpress;integrated security=true;"  providerName="System.Data.SqlClient"/>                       </connectionStrings>   9) Now it is time to create Linq to Entities queries to retrieve data from the database . Add a new class to your application in the CodeFirst folder.Name the file DALfootballer.cs We will create a simple public method to retrieve the footballers. The code for the class follows public class DALfootballer     {         FootballerDBContext ctx = new FootballerDBContext();         public List<Footballer> GetFootballers()         {             var query = from player in ctx.Footballers where player.FirstName=="Jamie" select player;             return query.ToList();         }     }   10) Place a GridView control on the Default.aspx page and leave the default name.Add an ObjectDataSource control on the Default.aspx page and leave the default name. Set the DatasourceID property of the GridView control to the ID of the ObjectDataSource control.(DataSourceID="ObjectDataSource1" ). Let's configure the ObjectDataSource control. Click on the smart tag item of the ObjectDataSource control and select Configure Data Source. In the Wizzard that pops up select the DALFootballer class and then in the next step choose the GetFootballers() method.Click Finish to complete the steps of the wizzard. Build your application.  11)  Let's create an Insert method in order to insert data into the tables. I will create an Insert() method and for simplicity reasons I will place it in the Default.aspx.cs file. private void Insert()        {            var footballers = new List<Footballer>            {                new Footballer {                                 FirstName = "Steven",LastName="Gerrard", Height=1.85, Weight=85,Age=32, JoinedTheClub=DateTime.Parse("12/12/1999"),Positions=FootballPositions.Midfielder,                Trainings = new List<Training>                             {                                     new Training {TrainingDuration = 3, TrainingLocation="MelWood"},                    new Training {TrainingDuration = 2, TrainingLocation="Anfield"},                    new Training {TrainingDuration = 2, TrainingLocation="MelWood"},                }                            },                            new Footballer {                                  FirstName = "Jamie",LastName="Garragher", Height=1.89, Weight=89,Age=34, JoinedTheClub=DateTime.Parse("12/02/2000"),Positions=FootballPositions.Defender,                Trainings = new List<Training>                                             {                                 new Training {TrainingDuration = 3, TrainingLocation="MelWood"},                new Training {TrainingDuration = 5, TrainingLocation="Anfield"},                new Training {TrainingDuration = 6, TrainingLocation="Anfield"},                }                           }                    };            footballers.ForEach(foot => ctx.Footballers.Add(foot));            ctx.SaveChanges();        }   12) In the Page_Load() event handling routine I called the Insert() method.        protected void Page_Load(object sender, EventArgs e)        {                   Insert();                }  13) Run your application and you will see that the following result,hopefully. You can see clearly that the data is returned along with the enum value.  14) You must have also a look at the database.Launch SSMS and see the database and its objects (data) created from EF Code First.Have a look at the picture below. Hopefully now you have seen the support that exists in EF 5.0 for enums.Hope it helps !!!

  Read the article

• Any software transforming broken lines into curves?

  - by brilliant

  Hello, do you know of any software that would help me transform a broken line into a curved line? For example, I have an octagon or a heptagon and I want it to be transformed into something resembling a circle. if you know such software, please, let me know. Thank You! Update A: Here is an image from the tutorial given to me by Jamie Keeling (right now it's the first answer below). At least the picture there represents what I want. In that tutorial this process is called "flattening paths". I will try to put that image right here, but if it doesn't get displayed, you can find it here: http://msdn.microsoft.com/en-us/library/ms536364%28v=VS.85%29.aspx The red line in the picture is what I would want to submit, and the blue line is what I would want to get in the end:

  Read the article

• Get multiple records with one query

  - by Lewy

  User table: name lastname Bob Presley Jamie Cox Lucy Bush Find users q = Query.new("Bob Presley, Cox, Lucy") q.find_users => {0=>{:name=>"Bob", :lastname=>"Presley"}, 1=>{:lastname=>"Cox"}, 2=>{:name=>"Lucy"}} Question: I've got hash with few names and lastnames. I need to build Activerecord query to fetch all users from that hash. I can do object = [] hash = q.find_users hash.each do |data| #check if data[:lastname] and data[:name] exist # object << User.where(:name => ..., :lastname => ...) end But I think it is higly inefficient. How should I do this ?

  Read the article

• Releasing NSData causes exception...

  - by badmanj

  Hi, Can someone please explain why the following code causes my app to bomb? NSData *myImage = UIImagePNGRepresentation(imageView.image); : [myImage release]; If I comment out the 'release' line, the app runs... but a few times calling the function containing this code and I get a crash - I guess caused by a memory leak. Even if I comment EVERYTHING else in the function out and just leave those two lines, when the release executes, the app crashes. I'm sure this must be a newbie "you don't know how to clean up your mess properly" kind of thing ;-) Cheers, Jamie.

  Read the article

• Move a sequential set of commits from one (local) branch to another

  - by jpswain09

  Is there a way to move a sequential set of commits from one (local) branch to another? I have searched quite a bit and still haven't found a clear answer for what I want to do. For example, say I have this: master A---B---C \ feature-1 M---N---O---P---R---Q And I have decided that the last 3 commits would be better off like this: master A---B---C \ feature-1 M---N---O \ f1-crazy-idea P---R---Q I know I can do this, and it does work: $ git log --graph --pretty=oneline (copying down sha-1 ID's of P, R, Q) $ git checkout feature-1 $ git reset --hard HEAD^^^ $ git checkout -b f1-crazy-idea $ git cherry-pick <P sha1> $ git cherry-pick <R sha1> $ git cherry-pick <Q sha1> I was hoping that instead there would be a more concise way to do this, possibly with git rebase, although I haven't had much luck. Any insight would be greatly appreciated. Thanks, Jamie

  Read the article

• the creation date of a database

  - by Robert Merkwürdigeliebe

  This is a question that originated from this question by Jamie. I thought I'll check Dougman's answer. What's happening here? A restore? select created from dba_users where username = 'SYS'; select min(created) FROM dba_objects; select created from v$database; CREATED ------------------------- 10-SEP-08 11:24:44 MIN(CREATED) ------------------------- 10-SEP-08 11:24:28 CREATED ------------------------- 18-DEC-09 15:49:00 Created from v$database is more than one year later than creation date of user SYS and SYS' objects.

  Read the article

• Possible to sort via two time stamps and display same row twice.

  - by jamiethompson90

  I'm looking at creating a time table solution. I have a task sheet that looks like Area 1 item 1 startTime endTime Area 1 item1 startTime endTime I wish to create a display where I can view what even is happening next, either endTime or startTime i.e. Newcastle reel 16:45 18:45 Newcastle reel2 17:45 19:45 would output Newcastle reel 16:45 Newcastle reel 17:45 Newcastle reel 18:45 Newcastle reel 19:45 More so, I would like to detect if the time is a startTime or an endTime would I have to enter two rows for each activity (time,area,item, start|end). I can make the interface to the creation of two rows. I just wondered if there was a better solution. Any input is appreciated, Thanks, Jamie

  Read the article

• Visual Studio 2010 Beta 2 Startup Failures

  - by Rick Strahl

  I’ve been working with VS 2010 Beta 2 for a while now and while it works Ok most of the time it seems the environment is very, very fragile when it comes to crashes and installed packages. Specifically I’ve been working just fine for days, then when VS 2010 crashes it will not re-start. Instead I get the good old Application cannot start dialog: Other failures I’ve seen bring forth other just as useful dialogs with information overload like Operation cannot be performed which for me specifically happens when trying to compile any project. After a bit of digging around and a post to Microsoft Connect the solution boils down to resetting the VS.NET environment. The Application Cannot Start issue stems from a package load failure of some sort, so the work around for this is typically: c:\program files\Visual Studio 2010\Common7\IDE\devenv.exe /ResetSkipPkgs In most cases that should do the trick. If it doesn’t and the error doesn’t go away the more drastic: c:\program files\Visual Studio 2010\Common7\IDE\devenv.exe /ResetSettings is required which resets all settings in VS to its installation defaults. Between these two I’ve always been able to get VS to startup and run properly. BTW it’s handy to keep a list of command line options for Visual Studio around: http://msdn.microsoft.com/en-us/library/xee0c8y7%28VS.100%29.aspx Note that the /? option in VS 2010 doesn’t display all the options available but rather displays the ‘demo version’ message instead, so the above should be helpful. Also note that unless you install Visual C++ the Visual Studio Command Prompt icon is not automatically installed so you may have to navigate manually to the appropriate folder above. Cannot Build Failures If you get the Cannot compile error dialog, there is another thing that have worked for me: Change your project build target from Debug to Release (or whatever – just change it) and compile again. If that doesn’t work doing the reset steps above will do it for me. It appears this failure comes from some sort of interference of other versions of Visual Studio installed on the system and running another version first. Resetting the build target explicitly seems to reset the build providers to a normalized state so that things work in many cases. But not all. Worst case – resetting settings will do it. The bottom line for working in VS 2010 has been – don’t get too attached to your custom settings as they will get blown away quite a bit. I’ve probably been through 20 or more of these VS resets although I’ve been working with it quite a bit on an internal project. It’s kind of frustrating to see this kind of high level instability in a Beta 2 product which is supposedly the last public beta they will put out. On the other hand this beta has been otherwise rather stable and performance is roughly equivalent to VS 2008. Although I mention the crash above – crashes I’ve seen have been relatively rare and no more frequent than in VS 2008 it seems. Given the drastic UI changes in VS 2010 (using WPF for the shell and editor) I’m actually impressed that the product is as stable as it is at this point. Also I was seriously worried about text quality going to a WPF model, but thankfully WPF 4.0 addresses the blurry text issue with native font rendering to render text on non-cleartype enabled systems crisply. Anyway I hope that these notes are helpful to some of you playing around with the beta and running into problems. Hopefully you won’t need them :-}© Rick Strahl, West Wind Technologies, 2005-2010

  Read the article

• Converting an Oracle VM VirtualBox VM into an Oracle VM Server image

  - by wim.coekaerts

  As we are working on tighter seemless moving of VM's between the 2 products, here are a few simple steps to convert an existing Oracle VM VirtualBox image over. Steps involved to make it easy/straightforward : (1) When creating a VM in Virtualbox, using Oracle Linux as an example, make sure that /etc/fstab only uses labels. Do not use hardcoded device names. instead of an entry /dev/sda1 /u01 ext3 defaults 1 1 use LABEL=foo /u01 ext3 defaults 1 1 for more info on labels : man e2label or use a logical volume /dev/VolGroup00/LVfoo /u01 ext3 defaults 1 1 Doing so will make it easier to have an OS boot up on a different hypervisor with potentially different device names. For instance, the VirtualBox VM might expose a scsi driver while in Oracle VM Server you might end up with an ide disk, this then changes /dev/sda to /dev/hda. (2) If you have a VM created that you want to convert, then shut down the VM in VirtualBox and convert the image files : go the the directory that contains your HardDisk image files (.VirtualBox/HardDisks/* as an example) for each of the virtual disks run the following command : VBoxManage clonehd virtualdiskfilename.vdi system.img --format raw where virtualdiskfilename.vdi is the original VBox VM file (this can also be a vmdk file) and system.img is the name of the virtualdisk for Oracle VM. this can be any filename as well, I typically use system.img to specify the boot disk (as is common for Oracle VM template creation) (3) create a vm.cfg To run a VM converted from VirtualBox, you have to create a vm.cfg for Oracle VM server that creates an HVM guest. The easiest is to use a simple hvm vm.cfg and change it for your vm. I have an example here : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' disk = ['file:system.img,hda,w', 'file:oracle.img,hdb,w',',hdc:cdrom,r',] kernel = '/usr/lib/xen/boot/hvmloader' memory = '1024' name = 'vmname' on_crash = 'restart' on_reboot = 'restart' pae = 1 serial = 'pty' timer_mode = '0' usbdevice = 'tablet' vcpus = 1 vif = ['bridge=xenbr0,type=ioemu'] vif_other_config = [] vnc = 1 vncconsole = 1 vnclisten = '0.0.0.0' vncpasswd = '' vncunused = 1 If you take the above vm.cfg, all you need to do - modify disk = (add your virtual disks in there) - modify memory = (amount of memory your VM needs) - modify name = (enter a name for your VM here) - modify vif = (might want to replace bridge=xenbr0 to the bridge you want to use) if you want more than 1 vcpu or other changes of course you have to make those as well. (4) copy this set of files onto your Oracle VM server or onto a webserver in a subdirectory and import the template through Oracle VM Manager. You can also just start the vm using xm create vm.cfg if you like. And that's it. As I said, we are working on automation around all this but it is relatively trivial to convert VM's over as long as you take the basic issues into account. Primarily the set up of the filesystems and the use of labels in /etc/fstab. There are other potential things to look at, such as network config. If you want to make that part clean then prior to shutting down the VM change /etc/modprobe.conf and/or add the mac address of the VM into the vm.cfg in the vifs line. The good thing, at least with Linux, is that even tho the virtual hardware changes, Linux will deal with it just fine (e1000 vs 8139 realtek, ide vs scsi etc). hope this helps.

  Read the article

• NetBeans PHP Community Council

  - by Tomas Mysik

  Hi all, today we would like to inform all of you that now you have a chance to improve NetBeans via NetBeans PHP Community Council. The author of this activity is Timur Poperecinii and he would like to tell you a few words about it. Hello passionate technical people, First of all let me introduce myself: my name is Timur, I’m a developer from Moldova (that little country between Romania and Ukraine), I develop mostly in .NET and JQuery, but I love to learn more, not being an expert I am familiar with Java (Struts2, Play), PHP (Symfony2), Ruby (Rails), Sencha Touch 2 and other technologies. I was “introduced” in PHP recently by a client of mine who requested to make the work specifically in PHP. Let me tell you a little story about my experience with open source and IDEs: when I was studying in university in 2007 I think, I did a simple little application in PHP and thought “Damn, if only there was a good IDE for PHP so I could relax and no having to remember all the function names”, then when I searched on internet pretty much everyone was using Vim or Emacs on Linux, but it had no autocomplete anyway, just syntax highlighting. I remember using some tool like Notepad++ I think. Nowadays everything changed, we have highlighting and autocomplete for about all standard things in PHP in many IDEs. I use NetBeans for PHP, and I really am happy with the experience I have there with standard PHP code, but for frameworks I still think there is lots of room for improvements. For example we have some Symfony 2 and Twig support. But I’d love to see more of that coming, for example I’m a big fan of file templates, where the main goal is to not waste time on writing over and over again something that can be generated, and it counts even more when you don’t have a lot of autocomplete. So what I thought, “Hey I know Java a little, and NetBeans has plugins, so may be it worth trying to do a file templates plugin”, and so I did, you can find details about my Unified Udevi Symfony2 Plugin for NetBeans 7.2 on my blog. It wasn’t hard, and it even was fun! Give back to open source Now think a little, NetBeans is an open source project and PHP support is just a part of it, so the resources are pretty limited in this area. But we as a community that uses this product, want to have the best possible experience with PHP and frameworks(!!!). So why don’t we GIVE BACK TO OPENSOURCE ? Imagine an IDE that can do all the things you wanted + it is free. Now how far is NetBeans from that point? I guess not so far – you might miss a little niche thing that you use on a daily basis, but then the question appears why don’t you make it happen on your own? NetBeans PHP Community Council What I proposed is to create a NetBeans PHP Community Council that will be formed of people willing to change something, willing to create plugins for their own needs and for the needs of the community, test the plugins created by them too, and basically evolve NetBeans in direction they want to reach. I already talked with the NetBeans PHP team. They are only happy to help this Council, with technical advises, opening some APIs we might need to have access to, and other things. One important thing to mention is that this Council is a Community project, so though we’ll have direct discussions with NetBeans PHP Dev team, NetBeans is not the leading force here, it is the community. You can see more details about the goals and structure I proposed at NetBeans PHP Community Council wiki page. We use this mail list: [email protected] for discussions and topics related to the Council. How can I join To join the NetBeans PHP Community Council please send an email to [email protected] with the subject of the mail starting with [Council New Member]. You can subscribe to this mail list here:http://netbeans.org/projects/php/lists. in your mail please indicate your location, age and experience both in Java and PHP. I need these data to assign you to a team. A response will be send to you with your next assignment and some people to contact. I really hope that you’ll make a step forward and try to make your everyday use of NetBeans even more fun.

  Read the article

• Managing Scripts in Oracle SQL Developer

  - by thatjeffsmith

  You backup your databases, right? You backup you home computer – your media collection, tax documents, bank accounts, etc, right? You backup your handy-dandy SQL scripts, right? Ok, now that I’ve got your head nodding, I want to answer a question I get every so often: How can I manage my scripts in SQL Developer? This is an interesting question. First, it assumes that one SHOULD manage their scripts in their IDE. Now, what I think the question generally gets around to is, how can we: Navigate to our scripts Open them Execute them What a good IDE should have is an interface to your existing Version Control System (VCS.) SQL Developer supports out-of-the-box both Subversion and Git. You can also download an extension via check-for-updates to get support for CVS. Now, what I’m about to show you COULD be done without versioning and controlling your scripts – but I want to ask you why you wouldn’t want to do this? So, I’m going to proceed and assume that you do INDEED version your scripts already. Seeing what scripts you’ve already got in your repository This is very straightforward – just open the Team Versions panel. Then connect to your repository. Shows you the files in your source control system. Now, I could ‘preview’ said file right away. If I open the file from here, we get a temp file copy down from the server to the local machine. This is a local temp copy of the controlled script – I can read/execute, but not write to it. And that might be all you need. But, if your script calls other scripts, then you’re going to want to check out the server copy of your stuff down your local SVN working copy directory. That way when your script calls another script – you’re executing the PRODUCTION APPROVED copies of said scripts. And if you do SPOOL or other file I/O stuff, it will work as expected. To get to those said client copies of your scripts… Enter the Files Panel The Files panel is accessible from the View menu. You can get to your files, one of two ways. If you’ve touched the file recently, you can see it under the Recent tree. Otherwise, you can navigate to your local ‘checked out’ copies of your script(s). Open your local copies, see what’s changed, etc. And I can access the change history and see what’s been touched… What changes am I going to ‘push out’ if I commit this back to the server? Most of us work on teams, yes? This panel also gives me a heads up if someone else is making changes to the same file. I can see the ‘incoming’ changes as well. To Sum It Up… If I want to get a script to run: do a full get to your local directory open the script(s) The files panel will tell you if your local copy is out of date from the server and if you have made local changes you’ve forgotten to commit back up to the server and your fellow teammates. Now, if you’re the selfish type and don’t want to share, that’s fine. But you should still be backing up your scripts, and you can still use the Files panel to manage your scripts.

  Read the article

• Book Review: Oracle ADF 11gR2 Development Beginner's Guide

  - by Grant Ronald

  Packt Publishing asked me to review Oracle ADF 11gR2 Development Beginner's Guide by Vinod Krishnan, so on a couple of long flights I managed to get through the book in a couple of sittings. One point to make clear before I go into the review.  Having authored "The Quick Start Guide to Fusion Development: JDeveloper and Oracle ADF", I've written a book which covers the same topic/beginner level.  I also think that its worth stating up front that I applaud anyone who has gone  through the effort of writing a technical book. So well done Vinod.  But on to the review: The book itself is a good break down of topic areas.  Vinod starts with a quick tour around the IDE, which is an important step given all the work you do will be through the IDE.  The book then goes through the general path that I tend to always teach: a quick overview demo, ADF BC, validation, binding, UI, task flows and then the various "add on" topics like security, MDS and advanced topics.  So it covers the right topics in, IMO, the right order.  I also think the writing style flows nicely as well - Its a relatively easy book to read, it doesn't get too formal and the "Have a go hero" hands on sections will be useful for many. That said, I did pick out a number of styles/themes to the writing that I found went against the idea of a beginners guide.  For example, in writing my book, I tried to carefully avoid talking about topics not yet covered or not yet relevant at that point in someone's learning.  So, if I was a new ADF developer reading this book, did I really need to know about ADFBindingFilter and DataBindings.cpx file on page 58 - I've only just learned how to do a drag and drop simple application so showing me XML configuration files relevant to JSF/ADF lifecycle is probably going to scare me off! I found this in a couple of places, for example, the security chapter starts on page 219 but by page 222 (and most of the preceding pages are hands-on steps) we're diving into the web.xml, weblogic.xml, adf-config.xml, jsp-config.xml and jazn-data.xml.  Don't get me wrong, I'm not saying you shouldn't know this, but I feel you have to get people on a strong grounding of the concepts before showing them implementation files.  If having just learned what ADF Security is will "The initialization parameter remove.anonymous.role is set to false for the JpsFilter filter as this filter is the first filter defined in the file" really going to help me? The other theme I found which I felt didn't work was that a couple of the chapters descended into a reference guide.  For example page 159 onwards basically lists UI components and their properties.  And page 87 onwards list the attributes of ADF BC in pretty much the same way as the on line help or developer guide, and I've a personal aversion to any sort of help that says pretty much what the attribute name is e.g. "Precision Rule: this option is used to set a strict precision rule", or "Property Set: this is the property set that has to be applied to the attribute". Hmmm, I think I could have worked that out myself, what I would want to know in a beginners guide are what are these for, what might I use them for...and if I don't need to use them to create an emp/dept example them maybe it’s better to leave them out. All that said, would the book help me - yes it would.  It’s obvious that Vinod knows ADF and his style is relatively easy going and the book covers all that it has to, but I think the book could have done a better job in the educational side of guiding beginners.

  Read the article

• Is It Worth It To Learn Experimental Languages

  - by Xander Lamkins

  I'm a young programmer who desires to work in the field someday as a programmer. I know Java, VB.NET and C#. I want to learn a new language (as I programmer, I know that it is valuable to extend what I know - to learn languages that make you think differently). I took a look online to see what languages were common. Everybody knows C and C++ (even those muggles who know so little about computers in general), so I thought, maybe I should push for C. C and C++ are nice but they are old. Things like Haskell and Forth (etc. etc. etc.) are old and have lost their popularity. I'm scared of learning C (or even C++) for this same reason. Java is pretty old as well and is slow because it's run by the JVM and not compiled to native code. I've been a Windows developer for quite a while. I recently started using Java - but only because it was more versatile and spreadable to other places. The problem is that it doesn't look like a very usable language for these reasons: It's most used purpose is for web application and cellphone apps (specifically Android) As far as actual products made with it, the only things that come to mind are Netbeans, Eclipse (hurrah for making and IDE with the language the IDE is for - it's like making a webpage for writing HTML/CSS/Javascript), and Minecraft which happens to be fun but laggy and bipolar as far as computer spec. support. Other than that it's used for servers but heck - I don't only want to make/configure servers. The .NET languages are nice, however: People laugh if I even mention VB.NET or C# in a serious conversation. It isn't cross-platform unless you use MONO (which is still in development and has some improvements to be made). Lacks low level stuff because, like Java with the JVM, it is run/managed by the CLR. My first thought was learning something like C and then using it to springboard into C++ (just to make sure I would have a strong understanding/base), but like I said earlier, it's getting older and older by the minute. What I've Looked Into Fantom looks nice. It's like a nice middleman between my two favorite languages and even lets me publish between the two interchangeably, but, unlike what I want, it compiles to the CLR or JVM (depending on what you publish it to) instead of it being a complete compile. D also looks nice. It seems like a very usable language and from multiple sources it appears to actually be better than C/C++. I would jump right with it, but I'm still unsure of its success because it obviously isn't very mainstream at this point. There are a couple others that looked pretty nice that focused on other things such as Opa with web development and Go by GOOGLE. My Question Is it worth learning these "experimental" languages? I've read other questions that say that if you aren't constantly learning languages and open to all languages that you aren't in the right mindset for programming. I understand this and I still might not quite be getting it, but in truth, if a language isn't going to become mainstream, should I spend my time learning something else? I don't want to learn old (or any going to soon be old) programming languages. I know that many people see this as something important, *but would any of you ever actually consider (assuming you didn't already know) FORTRAN? My goal is to stay current to make sure I'm successful in the future. Disclaimer Yes, I am a young programmer, so I probably made a lot of naive statements in my question. Feel free to correct me on ANYTHING! I have to start learning somewhere so I'm sure a lot of my knowledge is sketchy enough to have caused to incorrect statements or flaws in my thinking. Please leave any feelings you have in the comments.

  Read the article

• Very slow KVM in Ubuntu 12.04

  - by Guy Fawkes

  I use Ubuntu 12.04 64-bit and KVM, my CPU is Core i5 3.3 GHz and I have 8 GB of DDR3 RAM. I run Windows 7 in KVM and it's extremely slow. My co-worker use Debian on the same PC configuration and can run Windows 7 extremely fast! Where can be my problem? sudo cat /etc/libvirt/qemu/windows.xml <!-- WARNING: THIS IS AN AUTO-GENERATED FILE. CHANGES TO IT ARE LIKELY TO BE OVERWRITTEN AND LOST. Changes to this xml configuration should be made using: virsh edit windows or other application using the libvirt API. --> <domain type='kvm'> <name>windows</name> <uuid>5c685175-baea-0ca6-591f-8269d923ffb8</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='localtime'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/windows.img'/> <target dev='hda' bus='ide'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <controller type='ide' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='network'> <mac address='52:54:00:94:63:91'/> <source network='default'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <input type='tablet' bus='usb'/> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='ich6'> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='vga' vram='262144' heads='1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> </domain>

  Read the article

• Additional new material WebLogic Community

  - by JuergenKress

  Virtual Developer Conference On Demand - Register Updated Book: WebLogic 12c: Distinctive Recipes - Architecture, Development, Administration by Oracle ACE Director Frank Munz - Blog | YouTube Webcast: Migrating from GlassFish to WebLogic - Replay Reliance Commercial Finance Accelerates Time-to-Market, Improves IT Staff Productivity by 70% - Blog | Oracle Magazine Retrieving WebLogic Server Name and Port in ADF Application by Andrejus Baranovskis, Oracle Ace Director - Blog Using Oracle WebLogic 12c with NetBeans IDEOracle ACE Director Markus Eisele walks you through installing and configuring all the necessary components, and helps you get started with a simple Hello World project. Read the article. Video: Oracle A-Team ADF Mobile Persistence SampleThis video by Oracle Fusion Middleware A-Team architect Steven Davelaar demonstrates how to use the ADF Mobile Persistence Sample JDeveloper extension to generate a fully functional ADF Mobile application that reads and writes data using an ADF BC SOAP web service. Watch the video. Java ME 8 ReleaseDownload Java ME today! This release is an implementation of the Java ME 8 standards JSR 360 (CLDC 8) and JSR 361 (MEEP 8), and includes support of alignment with Java SE 8 language features and APIs, an enhanced services-enabled application platform, the ability to "right-size" the platform to address a wide range of target devices, and more. Learn more Download Java ME SDK 8It includes application development support for Oracle Java ME Embedded 8 platforms and includes plugins for NetBeans 8. See the Java ME 8 Developer Tools Documentation to learn JavaOne 2014 Early Bird RateRegister early to save $400 off the onsite price. With the release of Java 8 this year, we have exciting new sessions and an interactive demo space! NetBeans IDE 8.0 Patch UpdateThe NetBeans Team has released a patch for NetBeans IDE 8.0. Download it today to get fixes that enhance stability and performance. Java 8 Questions ForumFor any questions about this new release, please join the conversation on the Java 8 Questions Forum. Java ME 8: Getting Started with Samples and Demo CodeLearn in few steps how to get started with Java ME 8! The New Java SE 8 FeaturesJava SE 8 introduces enhancements such as lambda expressions that enable you to write more concise yet readable code, better utilize multicore systems, and detect more errors at compile time. See What's New in JDK 8 and the new Java SE 8 documentation portal. Pay Less for Java-Related Books!Save 20% on all new Oracle Press books related to Java. Download the free preview sampler for the Java 8 book written by Herbert Schildt, Maurice Naftain, Henrik Ebbers and J.F. DiMarzio. New book: EJB 3 in Action, Second Edition WebLogic 12c Does WebSockets Getting Started by C2B2 Video: Building Robots with Java Embedded Video: Nighthacking TV Watch presentations by Stephen Chin and community members about Java SE, Java Embedded, Java EE, Hadoop, Robots and more. Migrating the Spring Pet Clinic to Java EE 7 Trip report : Jozi JUG Java Day in Johannesburg How to Build GlassFish 4 from Source 4,000 posts later : The Aquarium WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Wiki Technorati Tags: WebLogic,WebLogic Community,Oracle,OPN,Jürgen Kress

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >