Search Results

Search found 3500 results on 140 pages for 'plug ins'.

Page 73/140 | < Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >

• USB flash drive unreadable after a few minutes on Windows 8

  - by B Sharp

  I recently got a new computer with Windows 8. I a have a number of large backup files I am moving from my old PC to my new one. I was able to successfully copy the files to a couple 16 GB flash drives. When I try to copy the files to my new computer, the process starts just fine but after copying about 4 GB of files, the copy stops. If I look at the drive in explorer, the drive is there, but I just get a busy cursor that stays indefinitely if I click it. If I unplug the flash drive and plug it back in, everything is fine again... for a couple minutes. I've tried copying from both flash drives with the same result. I've also tested this on the USB 2.0 and 3.0 ports on my motherboard with the same result (the drives are USB 2.0) It's also puzzling that this is happening since I previously used one of the same flash drives to install Windows 8 on this computer in the first place without any difficulty.

  Read the article

• administraitor denies command prompt

  - by roxas383

  I looked at the command prompt faqs on this webiste and tried to get me to make a new profile but when i went to open it it said "The command prompt has been disabled by your administraitor-click any key to countinue" and when i do it closes which i knew that was going to happen. Is there someway i can stop the admin from blocking my command prompt? oh and i was at school too (Dont know if this helps but i am in the West Allis West Milwaukee school district). Also, is there a way i can hack into the blocking program for my school at all? I don't remember what the program is but it might have to do with vision? I'm not sure but it would be greatly appreciated if someone could help (could i download a program on a flash drive that denies any blocking and/or disabling SafeSearch and plug it in into a computer at my school and use it from the flash drive? Would the school blocking thingy deny it from working?) HELP ME PLEASE!!!!!!!!!

  Read the article

• Configuring a Unified Communications Certificate for many virtual hosts running in Jetty

  - by rrc7cz

  I have a single IP with Jetty serving up X sites on port 80. Basically you can sign up for our service, then point your domain www.mycompany.com to that IP, and Jetty will serve up your custom site. I would like to add SSL support for all sites. To simplify things, I've looked at getting a single Unified Communications Certificate to plug into Jetty and have it work for all sites. Is this possible? Has anyone done this before? Does Jetty only support traditional, single-domain certs? What issues might I run in to compared to a single-domain cert?

  Read the article

• Nagios Check_hpjd giving me problems!

  - by Mister IT Guru

  When I run the following [root@host plugins]# ./check_hpjd -H printer1.mydomain.com : Timeout from host printer1.mydomain.com I have Net-snmp installed on my system, I noted that i didn't have net-snmp-utils installed, and then I was able to run [root@host plugins]# snmpwalk -Os -c public -v 1 printer1.mydomain.com system sysDescr.0 = STRING: HP ETHERNET MULTI-ENVIRONMENT sysObjectID.0 = OID: enterprises.11.2.3.9.1 sysUpTimeInstance = Timeticks: (325408663) 37 days, 15:54:46.63 sysContact.0 = STRING: sysName.0 = STRING: printer1 sysLocation.0 = STRING: sysServices.0 = INTEGER: 72 So I know that the printer is working as expected, (as far as SNMP is concerned). But when I run [root@host plugins]# ./check_hpjd -H printer1.mydomain.com -C public Error in packet () I get this error - From what I've tried so far, I know my host can communicate via SNMP, I know the printer responds via SNMP, so I guess I'm left to look at the plug-in, which I will be checking up on. I'm new to SNMP, I am investigating this with my good friend Google search, but I am on a learning curve here, so please forgive my questions if they sound stupid,

  Read the article

• BSOD on windows 7 with SSD during boot after improper shutdown

  - by Bob

  I have a BSOD on windows 7 with SSD during boot after improper shutdown (while windows animation logo is moving). The computer restart imediatly after BSOD, and windows proposes to launch startup repair (if i do it, it takes +-5min and fixes the problem : computer starts normally). However, after any new improper shutdown, i got the same problem. Remarks: If i unplug, re-plug the SSD whyle system is shutdown, i have the same problem. If i reproduce the situation with old HDD, i havn't the problem Previously, i had a different problem: BSOD when waking up after sleep, which was fixed by installing drivers (ethernet, usb, graphic card) I have made ram chech and ssd check and found no problems Starting with safe mode after improper shutdown causes a BSOD at loading of classpnp.sys Configuration: System: HP compaq 8510p SSD: OCZ vertex-2 2.5 Boot options: SATA native mode - Enable, HDD transalation mode - LBA-assisted

  Read the article

• Format Factory not working for mov files

  - by LanguaFlash

  I have attempted multiple destination formats with no success. I am using Format Factor 2.30. I drag and drop a .mov file into FF, select all to mpg (or any format) then click Start. It thinks for a couple seconds and then jumps to 100%. When I open the file I get no sound or picture from the video. These mov files were created with a Canon SX10 camera. (It is my brother's camera so I'm not sure of the model.) Any suggestions? TMPGEnc is able to convert the files with the QTReader plug in so the video isn't corrupted or something. Thanks. Jeff

  Read the article

• Zero-channel RAID for High Performance MySQL Server (IBM ServeRAID 8k) : Any Experience/Recommendation?

  - by prs563

  We are getting this IBM rack mount server and it has this IBM ServeRAID8k storage controller with Zero-Channel RAID and 256MB battery backed cache. It can support RAID 10 which we need for our high performance MySQL server which will have 4 x 15000K RPM 300GB SAS HDD. This is mission-critical and we want as much bandwidth and performance. Is this a good card or should we replace with another IBM RAID card? IBM ServeRAID 8k SAS Controller option provides 256 MB of battery backed 533 MHz DDR2 standard power memory in a fixed mounting arrangement. The device attaches directly to IBM planar which can provide full RAID capability. Manufacturer IBM Manufacturer Part # 25R8064 Cost Central Item # 10025907 Product Description IBM ServeRAID 8k SAS - Storage controller (zero-channel RAID) - RAID 0, 1, 5, 6, 10, 1E Device Type Storage controller (zero-channel RAID) - plug-in module Buffer Size 256 MB Supported Devices Disk array (RAID) Max Storage Devices Qty 8 RAID Level RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 1E Manufacturer Warranty 1 year warranty

  Read the article

• How to find the /dev name of my USB device

  - by mustafa

  I am running Ubuntu 11 on VmWare on Windows XP. I want to format an SD card in Ubuntu. But, I can't figure out which /dev/xxx device the SD card is. I plug the card into the built-in socket of my laptop. I "safely remove" the device in Windows. Then, I "connect" the PCMCIA reader in VmWare. Now, I was supposing to see a new device like /dev/sdx. But, it doesn't appear :( How can I find what the name of my USB device's name and mount it? /var/log/message is empty. Here is the output of dmesg: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd And, here is the last lines of /var/log/syslog: Oct 31 18:51:21 ubuntu kernel: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd Oct 31 18:51:21 ubuntu mtp-probe: checking bus 2, device 12: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1" Oct 31 18:51:21 ubuntu mtp-probe: bus: 2, device: 12 was not an MTP device

  Read the article

• Can't initialize drive in Windows 7

  - by Abe

  I have a 2.5" laptop harddrive that I plugged into my laptop through a SATA to USB cable. It's powered by an adapter to a normal wall-plug. I want to use it as an external harddrive. It wouldn't initialize (Device is not ready), so as suggested in some instructions I found I uninstalled the drivers, unplugged it and plugged it back in. That worked, and I initialized the drive and formatted it. However I unplugged it after that and a few days later the same strategy does not work and I can't figure out how to use the drive. I can't initialize it and it doesn't show up in my computer.

  Read the article

• OpenWrt Backfire 10.03 Frequently Becoming Unresponsive (Bridged Client)

  - by Christopher Parker

  I have a Linksys WRT54G version 2 that I've flashed with OpenWrt Backfire 10.03. It's acting as a bridged client using the wl.o driver to give me network access in my home office, which is in a far corner of my house in a position that would make it exceedingly difficult to fish network cabling in through the walls. I have three network-ready devices attached to the device that don't currently support WiFi, including a networked printer. Ever since I migrated from WhiteRussian, which was also set up as a bridged client, to Backfire, the device has been becoming unresponsive, as though the OS itself has crashed or frozen. The WLAN light becomes completely solid and the LAN lights stay mostly solid, blipping off and then back on again maybe once a second or so. They all blink more or less in unison. Is there some way I can diagnose why this is happening so I can fix it? Right now, the only way to fix it is to unplug the device and plug it back in.

  Read the article

• VGA resolution with Sony Bravia TV

  - by prestomation

  I just bought Sony Bravia KDL40S5100 tv. The VGA input is acting weird. I have a Gateway desktop with Windows 7 and Intel 945 graphics. I also have a laptop running Ubuntu 9.04. The TV will not display the gateway when the resolution is over 1360x768, I have to wait for it to time out and bring me back. The Intel driver even urges me to switch to the "recommended" 1920x1080. I just installed Win7 using this tv as the monitor. When the orginial welcome screen started after setup, it started me at 1080. I had to start in safemode to set a res that would work! When I plug my laptop into the TV, 1920x1080 works just fine. Any ideas? This laptop also has Win7, which I am going to try, but I haven't gotten a chance yet.

  Read the article

• Why did my laptop turn off?

  - by darenw

  Normally I can slip my running laptop into a backpack, go somewhere, and if it's no more than about half an hour later, it'll still be running. At the destination I plug in the AC power unit and all is well. I run it off of the AC unit before and after the trip, have the screen at less than full backlight brightness, and don't have any peripherals that burn power. Sometimes the wireless switch accidentally slides in the backpack, and that causes extra power to be used and the laptop dies before I reach the destination. Sad, but so be it. But sometimes the wireless switch is off, I've reached the destination in less than 30 minutes (typically 10-20 min), and I know the battery was fully charged, yet the machine is off. Is there a way to determine, after the fact, why the machine shut itself off? I'm running Linux on a fairly powerful Gateway with 4GB RAM, fancy nvidia graphics, dual core cpu, chosen more for number crunching power than battery life, but should last easily for half an hour if not an hour.

  Read the article

• Can storage-spaces drives be moved to a replacement server when there is a failure

  - by Joe C

  I have tried to search here and Google, but cannot find a case explaining this. Storage spaces is similar to software raid. If the server fails due to motherboard or some other issue, can the drives that comprise that storage spaces config be moved to another win2k12 server without restoring from backup? This can be done in linux software raid. If so, does the storage space config have to be re-created prior to the move, or do the drives hold the config so they are essentially plug and play? Thanks.

  Read the article

• My control key doesn't work, how do I fix it??

  - by Blaine LaFreniere

  My control key on the right doesn't work how it should. E.g. Right ctrl + T won't open new tabs in firefox, right ctrl + w won't switch windows in vim, etc. I know the key isn't physically broken, because xev shows that the right ctrl key generates events, but it just isn't responding as I expect it to in applications. Screenshot: http://i46.tinypic.com/33w1h76.png I tried Kim's answer but it still doesn't work. blaine@blaine-laptop ~ $ xmodmap -pke | grep 105 keycode 105 = Control_R Control_R Control_R Control_R Control_R Tried to map as Control_L as well, didn't work. The computer is a laptop, I am unable to plug the keyboard in to another computer.

  Read the article

• Suggestion for boot manager in external hard disk

  - by Korrupzion

  Hi, I just bought an 1TB External Hard drive with eSATA, USB, FW400/800 (LaCie if you are interested). I already put the windows 7 installation in a FAT32 active partition so i can plug the HDD via USB, since my notebook or other computers doesn't support boot via eSATA commonly, and it works. Now i want to do more partitions so i'm looking for a way to have a boot manager as active partitions that allows me to boot from different partitions in my HDD (win7, ubuntu installations for example) I want to know if you know any software to do this or you already have this system. Thanks and sorry i have too many grammar errors because english is not my native language :)

  Read the article

• Wireless DHCP doesn't work until wired Ethernet plugged in

  - by MT_Head

  A client of mine has an Asus R1F tablet running Windows XP Tablet SP3. It has an Intel 3945ABG wireless card; wired Ethernet is a Realtek something-or-other. In the past few days, it's developed an odd problem: WiFi authenticates, but can't get an address via DHCP. plug in wired Ethernet - both interfaces get good addresses unplug cable, WiFi continues to work until shutdown. Next morning, repeat process. I've tried: turning WiFi off/on (there's a slider switch) disabling/re-enabling via Device Mangler uninstalling and reinstalling the driver for the 3945ABG... changing from Intel Pro/SET to Windows Wireless Zero Config (and back) restarting the router changing the static DHCP assignments at the router upgrading the router firmware, just on general principles The router/access point is pfSense 1.2.3RC1 (was 1.2.2); wireless card is Atheros-based. None of the 12 other users (5 with tablets) are having problems.

  Read the article

• ATI Radeon 5850 I cant seem to get 3 monitors up at the same time. 2 Monitors and a HDTV but still.

  - by Jan

  Ive just bought the top end ATI Radeon card with 2 normal monitor ports and a HDMI. The idea was to continue using my dual screen setup as always and to use the last plug, the HDMI on my TV. I got a new 52 inch HD TV with all the necessary bits. This should work fine. But.. in Display Properties I still get only my 2 monitors up as options. Not the Digital TV. When I unplug 1 monitor and restart the computer, I get the TV and the other monitor. But never all 3 at the same time. Why is this ? Where can I go to tell it that I need all 3 screens at the same time. Also I get a message saying my gfx card also gives sound through the HDMI cable.. But the TV tells me its recieving a sound format that it does not understand. Any ideas on that too while were at it ?

  Read the article

• Harddrive in the freezer ever work for you?

  - by Stefan Thyberg

  Once upon a time, my little 10 GB drive in my webserver failed and of course I had no backup, teaching me to immediately set up an automatic backup job afterwards. Anyhow, this drive refused to start and as a last-ditch effort I put it in a plastic bag and put it in the freezer overnight, since I had heard somewhere that it might work and I really didn't have any other options. The next day I take it out, immediately plug it in outside the case and lo and behold, the drive works long enough for me to copy my data off it. Have you ever had a similar experience with this method?

  Read the article

• SATA hard disk for laptop on Desktop PC

  - by Lawliet

  I know that this forum is for programming-related questions only, but I'm having this dilemma so here I go. Can I connect a laptop SATA hard disk to Desktop PC? Do I have to use some adapters or I can just plug in SATA power connector and SATA data cable like my Desktop hard disk is connected? I noticed that both laptop and desktop SATA disks use same connectors, but I'm afraid that I might fry my laptop hard disk because the SATA connector has both 12V and 5V voltage (given the fact that laptop hard disks has input voltage of 5V) Thanks in advance

  Read the article

• Digital audio does not work on MacBook Pro

  - by mathk

  I have a MacBook Pro (8,2). Using a TOSLINK cable I have no digital output. Oddly enough, sometime I can hear a glitch when I plug in the cable or when I give it a gentle wiggle. My guess is that the output is not correctly detecting that I have a digital link. So is there a way to force digital audio output on a MacBook Pro? Some say that in the Audio MIDI Setup there is an option but I can't find it. I am running OS X 10.7.5.

  Read the article

• Laptop stopped recognizing USB hard drive

  - by vahokif

  Hi, My Packard Bell EasyNote TX86 laptop stopped recognizing my 1 TB Toshiba Store Art hard drive. It worked fine until now, and it still works on other computers. Other USB devices (including storage) work, and I've tried plugging it in every port, to no avail. When I plug it in it spins up, but Windows doesn't react at all (it's not in disk management), Linux doesn't write anything in dmesg and I can't see it in BIOS setup. I didn't use it at all today, apart from plugging it into a freshly-installed Windows 7 machine once (where it worked). What can I do? Which device is to blame here? EDIT: One more thing. I unplugged the drive while the laptop was hibernated. Google says this might be the problem and it might have something to do with resetting the USB Host Controller.

  Read the article

• Start FF with plugins disabled.

  - by justSteve

  Strange problem. Opened FF 3.6.3 after a re-boot and my last opened tabs appeared but none of the page or menu elements would respond to a click. No error messages...just locked up. Started FF with a different profile and it works normally. Next i used FEBE to restore a backup of my working profile and, after the restore, it's doing the same thing - locked out. No newly installed plugins but since a brand new profile works while a restored one doesn't it kinda points to a problematic plug-in. Is there any way to start FF with all plugins disabled? thx

  Read the article

• usb device in dual mode on gentoo linux

  - by Idlecool

  i am having a flip flop usb modem which has two modes 1 usb mass storage mode: root@devbox:/media/F872F0FD72F0C184/Users/idlecool/Downloads# lsusb Bus 006 Device 003: ID 19d2:fff5 ONDA Communication S.p.A. 2 usbserial mode: root@devbox:/media/F872F0FD72F0C184/Users/idlecool/Downloads# lsusb Bus 006 Device 003: ID 19d2:fffe ONDA Communication S.p.A. by default whenever i plug the modem to the usb port.. the linux machine recognize it as a usb mass storage device.. how can i make it load as usbserial device i have been using a package usb_modeswitch in the past on ubuntu 10.04 but i cannt install the same package on gentoo live cd.. even udev is not installed on live cd.. how to change the product-id of the usb device on gentoo live disc without udev.

  Read the article

• Is there such a thing as an IP femtocell, and what does it do?

  - by The Journeyman geek

  My dad mentioned a co-worker suggested using a device, that might use CDMA to route calls through IP to save costs on a certain overseas project we're on- since our home base is quite far from there. I've never heard of such a device, so if it does exist, I'm wondering, if it's specific to particular ISPs, or if you can just pick one off the shelf, plug it into an arbitrary Internet connection, and make calls using it and a cellphone of some sort? As you can tell, details are sketchy, so... if such a device doesn't exist, saying so might be a right answer ;)

  Read the article

• Use wired LAN adapter by default

  - by Frantumn

  I am trying to find out if there's a way to set up network adapters so that if 2 are connected with network and internet access it will choose one over the other. Scenario: I have seen several computers running Windows 7 or Windows 8 where you are connected to a wireless network, working perfectly. Then when you plug in an Ethernet cable, it still shows the network icon in the taskbar as wireless. I would like to have my computer set up so that if there's an Ethernet cable plugged in, it uses that, and not the wireless adapter. 1) Is this possible / How? 2) Why does it stay on wireless over wired when given the option for both?

  Read the article

< Previous Page | 69 70 71 72 73 74 75 76 77 78 79 80  | Next Page >