Search Results

Search found 23949 results on 958 pages for 'test test'.

Page 737/958 | < Previous Page | 733 734 735 736 737 738 739 740 741 742 743 744  | Next Page >

• Some URLs fail to load on Windows web portal

  - by jpolache

  I’m working in a large data center and have been assigned to troubleshoot and issue with a windows (IIS) web server that acts as a portal for a customer of the data center. This portal server is on a DMZ at the local data center. I don’t have access to the portal desktop and am relying on an off-site administrator to work with me to do testing and report the condition of the portal. He tells me there are no software firewalls or other filtering configured. While most of the remote web pages work fine, several of the URSs the portal is suppose to serve up fail to load. I had wireshark installed on the portal system and had a capture taken of one of the failures. I used IE to access one of the remote web servers at issue. I could see the TCP SYN-ACK coming back from the remote server, but after several HTTP GETs fail to get a response the portal server sends a reset. The webmaster of the remote web server assures me that no sites are being blocked. I had a capture taken outside the local firewall, so there should be no issue there. Another tech set up a laptop and used the IP address of the portal (we took the portal off-line for the test). The laptop loads the URL as expected. I tried having Firefox loaded to make sure that the HTTP GET was not mal-formed. Same failure as with IE. So, it seems it is not the remote web server or the network, because there was no problem with the laptop. At this point, I’m not sure what other questions to ask or tests to do.

  Read the article

• Active directory Kerberos OSX problems

  - by Temotodochi

  I'll try to keep this short, but informative. I'm currently unable to bind OSX lion (10.7.4) machines to our AD. OSX kerberos (heimdal) is unable to locate the KDC service. However i can bind linux & windows machines to the AD without any problems in the same network AD controls the domain DNS and all the relevant _kerberos._tcp.x.domain.com and _kpasswd SRV DNS records are there and resolve fine when tried from OSX machines. Defined ports are open for service and manually accessible from OSX. When i try kinit in the OSX, i can get the first auth through (wrong passwords fail instantly), but when supplied with correct password, kinit fails after some waiting with "unable to reach KDC". All machines run NTP and have correct time. During testing, network is not firewalled between the machines Linux and windows machines have no problems whatsoever I have tried with and without /etc/krb5.conf - OSX by default does not need it in the krb5.conf i used a working config from one of our linux machines. dsconfigad fails with simple "connection failed to the directory server" I'm a bit baffled with this. OSX is like the KDC is nowhere to be found and at the same time my test machines with windows 7 and some linux (centos 6 & debian 6) machines have no problems whatsoever. Same network, same configurations. I'm missing some vital piece of configuration somewhere, and i can't find out what it is.

  Read the article

• Setting up Mako with Cherrypy on nginx through FastCGI

  - by xuniluser

  I'm trying to use TemplateLookup from Mako, but can't seem to get it to work. Layout of the test site is: /var/www main.py templates/ index.html Nginx's config is setup as: location / { fastcgi_pass 127.0.0.1:8080; fastcgi_param SERVER_NAME $server_name; fastcgi_param SERVER_PORT $server_port; fastcgi_param SERVER_PROTOCOL $server_protocol; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param QUERY_STRING $query_string; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_pass_header Authorization; fastcgi_intercept_errors off; } Cherrypy's config has: [global] server.socket_port = 8080 server.thread_pool = 10 engine.autoreload_on = False tools.sessions.on = True A simple cherrypy setup in main.py seems to work fine. import cherrypy class Main: @cherrypy.expose def index(self): return 'Hello' cherrypy.tree.mount(Main(), '/', config='config') Now, if I modify this to use Mako's template lookup, I get a 500 error. I know it has something to do with serving static files, but I've tried over a dozen different configurations accoring to the cherrypy wiki, but none of them work. Here's a bare setup I have for the templates: import cherrypy from mako.template import Template from mako.lookup import TemplateLookup templates = TemplateLookup(directories=['templates'], output_encoding='utf-8') class Main: @cherrypy.expose def index(self): return templates.get_template('index.html').render(msg='hello') cherrypy.tree.mount(Main(), '/', config='config') Does anyone know how I can get this to work ?

  Read the article

• SQL Server 2008 R2 - Cannot create database snapshot

  - by Chris Diver

  Server: Windows Server 2008 R2 X64 Enterprise SQL: SQL Server 2008 R2 Enterprise X64 I have a default SQL Server instance, the SQL Server service account is running as a domain user. I am trying to create a database snapshot in the directory where the mdf files are stored. The T-SQL syntax is correct. The file system is NTFS. The error message I get is: Msg 1823, Level 16, State 2, Line 1 A database snapshot cannot be created because it failed to start. Msg 5119, Level 16, State 1, Line 1 Cannot make the file "e:\MSSQL10_50.MSSQLSERVER\MSSQL\DATA\TestDB.ss" a sparse file. Make sure the file system supports sparse files. The local SQLServerMSSQLUser$db$MSSQLSERVER group has Full Control permission on the folder where I am trying to create the snapshot. I can fix the problem in two ways, neither of which are suitable. Add the SQL Server service (domain) account to the local Administrators group and restart the SQL service. Grant the local SQLServerMSSQLUser$db$MSSQLSERVER group Full control on E:\ I have tried to change the owner of the DATA directory to SQLServerMSSQLUser$db$MSSQLSERVER to no avail. I have no issue creating a new database Why can I not create a snapshot by giving permission only on the DATA folder? Update 23/09/2010: I have tried mrdenny's suggestion with no luck (but learned something new in the process), I suspect the problem may be due to the fact that the domain is a windows 2000 domain running in mixed mode. I had to install hotfix KB976494 for Server 2008 R2, as the SQL Server 2008 R2 installer would not verify the service account correctly with the domain. I noticed that Server 2000 isn't a supported operating system for SQL 2008 R2 but cannot find anything that would suggest it shouldn't work in a 2000 domain. I dis-joined the test server from the domain and changed the service accounts to the local service account and I still have the same issue. I will try to re-install the server without joining the domain and without the hotfix and see if the issue persists.

  Read the article

• Outlook 2007/2010 autodiscovering old Exchange info

  - by Dan

  I currently have an Exchange setup as follows: two Exchange 2003 servers clustered together set up as the current mailbox stores, one Exchange 2003 setup as a frontend, one Exchange 2007 set up as a frontend (was set up for testing by my predecessor, never really used intentionally), and now four Exchange 2010 servers - two mailboxes in a DAG and two with Hub/CAS. Everything seems to be working fine with one exception - Outlook 2007/2010 clients are still autodiscovering the test 2007 frontend and not the 2010 CAS array. I know this because there's an expired cert on the 2007 box so the client displays a cert error when you attempt to autocreate the outlook profile. From what I've read, there is an SCP (Service Connection Point) in AD that is pointing to the old server and it is getting returned first, causing Outlook to try it first. How can I prevent Outlook from even attempting to connect to this 2007 box from now on? http://www.msexchange.org/articles_tutorials/exchange-server-2010/management-administration/exchange-autodiscover.html When Outlook 2007 is installed on a domain joined workstation then the Outlook client will query Active Directory for the Autodiscover information. Active Directory will return a list of SCP’s and the Outlook client will automatically select the first SCP in this list. Using the information found in the SCP the Outlook client will contact the Client Access Server for its configuration information and the Outlook client will be configured automatically.

  Read the article

• Creating basic, redundant gigE or IB storage network for Xen?

  - by StaringSkyward

  With only a modest budget, I want to move my 4 xen servers over to network storage -either NFS or iSCSI which will be determined based on how well it performs when we test it (we need good throughput and it must continue to work through link and switch failure tests). We may add another couple of xen servers at some point when this is done. I don't know much about the design and operation of storage networks, so would really appreciate some hints from those with experience. The budget is around $3,800 excluding the storage appliance. I am currently thinking these are my options to remain on budget: 1) Go for used infiniband hardware and aim for 10gb performance. 2) Stick with gig ethernet and buy some new switches (cisco or procurve) to create a storage-only ethernet LAN. Upgrade to 10gigE later but try to use hardware capable of it where possible to reduce upgrade costs. I have seen used, warrantied infiniband switches at reasonable prices (presumably because big companies are converging on 10gbit ethernet?) and the promise of cheap 10gb is attractive. I know nothing about IB, so here come the questions: Can I buy 2 x switches and have multiple HBAs in my xen and storage nodes to get redundancy and increased performance without complexity or expensive management software costs? If so, can you point me to some examples? Do NFS and iSCSI work just the same regardless? Is IB a sensible choice or could/should I use ethernet or FC on the same budget - I'm keen not to get boxed into a corner for future upgrades, however. For the storage I am likely to build a storage server using nexentastor with the intention that I can later add more disks, SSDs and add another server to provide a failover option at the storage level. An HP LeftHand starter SAN is also under consideration, too. Thanks in advance.

  Read the article

• postfix says mail sent ok, message does not arrive in ISPs inbox? no reject in log?

  - by Nick

  When I send a test message from my mail server to my @bellsouth.net email, The postfix log shows it was sent OK, but the message never arrives in my bellsouth inbox. Shouldn't I get a failure notice or a bounce if At&T is blocking the messages? I'm trying to troubleshoot why some customers aren't getting emails, but if there's nothing in mail.log to say the message is rejected, how do I know which messages were delivered successfully? The log shows: Feb 27 09:02:36 MyHOSTNAME postfix/pickup[26175]: D53A72713E5: uid=0 from=<root> Feb 27 09:02:36 MyHOSTNAME postfix/cleanup[26487]: D53A72713E5: message-id=<[email protected]> Feb 27 09:02:36 MyHOSTNAME postfix/qmgr[5595]: D53A72713E5: from=<[email protected]>, size=878, nrcpt=1 (queue active) Feb 27 09:02:37 MyHOSTNAME postfix/smtp[26490]: D53A72713E5: to=<[email protected]>, relay=gateway-f1.isp.att.net[204.127.217.16]:25, delay=0.57, delays=0.11/0.03/0.23/0.19, dsn=2.0.0, status=sent (250 ok ; id=20120227140036M0700qer4ne) Feb 27 09:02:37 MyHOSTNAME postfix/qmgr[5595]: D53A72713E5: removed The AT&T server accepted the message, right? I happen to have an At&T/Bellsouth email, but I don't have an account with every ISP we send to. I need some way of knowing if a message is getting to its destination or not. Is there any setting in my main.cf file that would affect whether or not we get reject/bounce notices?

  Read the article

• How do I configure permissions for a cluster share using Powershell on 2008?

  - by Andrew J. Brehm

  I have a cluster resource of type "file share" but when I try to configure the "security" parameter I get the following error (excerpt): Set-ClusterParameter : Parameter 'security' does not exist on the cluster object Using cluster.exe I get a better result, namely the usual nothing when the command worked. But when I check in Failover Cluster Manager the permissions have not changed. In Server 2003 the cluster.exe method worked. Any ideas? Update: Entire command and error. PS C:\> $resource=get-clusterresource testshare PS C:\> $resource Name State Group ResourceType ---- ----- ----- ------------ testshare Offline Test File Share PS C:\> $resource|set-clusterparameter security "domain\account,grant,f" Set-ClusterParameter : Parameter 'security' does not exist on the cluster object 'testshare'. If you are trying to upda te an existing parameter, please make sure the parameter name is specified correctly. You can check for the current par ameters by passing the .NET object received from the appropriate Get-Cluster* cmdlet to "| Get-ClusterParameter". If yo u are trying to update a common property on the cluster object, you should set the property directly on the .NET object received by the appropriate Get-Cluster* cmdlet. You can check for the current common properties by passing the .NET o bject received from the appropriate Get-Cluster* cmdlet to "| fl *". If you are trying to create a new unknown paramete r, please use -Create with this Set-ClusterParameter cmdlet. At line:1 char:31 + $resource|set-clusterparameter <<<< security "domain\account,grant,f" + CategoryInfo : NotSpecified: (:) [Set-ClusterParameter], ClusterCmdletException + FullyQualifiedErrorId : Set-ClusterParameter,Microsoft.FailoverClusters.PowerShell.SetClusterParameterCommand

  Read the article

• IIS Windows Authentication not working in Internet Explorer via host name; works via IP

  - by jkohlhepp

  I'm trying to get a new Windows Server 2003 box working to host an ASP.NET application that uses Windows Authentication. Here's some info: IIS Anonymous Access is diabled IIS Integrated Windows Authentication is enabled I've tried it with and without Digest Authentication and it is the same result Both my machine and the server are in same active directory domain on the same intranet I'm using IE 6 My symptoms: In Firefox, via either IP or host name, a login box pops up, and if I enter my NT credentials, it works. In IE, via the server IP address, it works perfectly with no login box. In IE, via the server host name, it pops up a login box but even if I put in the correct credentials, it just pops up the box again. This is the problem. Why won't windows auth work in IE via host name but it will via IP address? Edit: Here's something else interesting. If I go into my Internet Explorer advanced settings and disable Windows Authentication, it seems to work just fine. And by work I mean that my test .NET app sees my NT ID as the current user.

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• Emails sent through SMTP on VPS are considered to be spam

  - by Ilya

  During our business we have to make regular mailing to our clients: invoices, information emails, etc. Previously we received and sent emails using mail server of our hosting provider. But as the number of clients increased, we have to order VPS and install our own SMTP server their for performing our mailings. So, now we have default provider mail server for receiving emails, let it be business.com. We have email accounts like [email protected], etc. We use this mail server to receive emails and manage our email accounts. And we have SMTP server which is running on VPS. We use this SMTP only for sending emails with From addresses like [email protected]. VPS has default DNS records created by provider, let it be IP.AD.RE.SS <- ip-ad-re-ss.provider.com. Mailings are made using either desktop email clients or custom Java-based application which uses JavaMail for sending emails. The problem is that most of emails sent by us are placed in spam folders in clients email accounts. Clients have their email in Gmail, Yahoo, Hotmail, etc. Could you please tell what is the most probable reason and solution of described problem? Are there any service in Intranet where we can send test email and get an answer with description why this email could be considered to be spam?

  Read the article

• Internet slowed down because of SQUID Server setup

  - by Ranjith Kumar

  Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

  Read the article

• Will adding a SSD cache device to my ZFS storage improve performance?

  - by Sysadminicus

  The server has 4GB of RAM and my zpool is made up of 15.5k SAS drives arranged like this: NAME STATE READ WRITE CKSUM tank ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c0t2d0 ONLINE 0 0 0 c0t3d0 ONLINE 0 0 0 c0t4d0 ONLINE 0 0 0 c0t5d0 ONLINE 0 0 0 c0t6d0 ONLINE 0 0 0 c0t7d0 ONLINE 0 0 0 c0t8d0 ONLINE 0 0 0 raidz1-1 ONLINE 0 0 0 c0t10d0 ONLINE 0 0 0 c0t11d0 ONLINE 0 0 0 c0t12d0 ONLINE 0 0 0 c0t13d0 ONLINE 0 0 0 c0t14d0 ONLINE 0 0 0 spares c0t9d0 AVAIL c0t1d0 AVAIL The primary use is as an NFS store for a couple VMWare ESXi servers. I can't do any "true" benchmarks because this is a production system (no budget for test systems), but using dd and bonnie++ I can't get more than ~40-50MB/s writes and ~70-90MB/s reads. It seems I should be able to do much better, but I'm not sure where to optimize. Based on what I've read, I think dropping in a OCZ Vertex 2 Pro SSD as my L2ARC is going to be the best bang-for-the-buck to improve througput. Is there something else I should be looking into to help performance? If not... How do I know how big a cache device I need? Am I safe with only a single SSD as my cache device?

  Read the article

• Can't make Dovecot communicate with Postfix using SASL (warning: SASL: Connect to private/auth failed: No such file or directory)

  - by Fred Rocha

  Solved. I will leave this as a reference to other people, as I have seen this error reported often enough on line. I had to change the path smtpd_sasl_path = private/auth in my /etc/postfix/main.cf to relative, instead of absolute. This is because in Debian Postfix runs chrooted (and how does this affect the path structure?! Anyone?) -- I am trying to get Dovecot to communicate with Postfix for SMTP support via SASL. the master plan is to be able to host multiple e-mail accounts on my (Debian Lenny 64 bits) server, using virtual users. Whenever I test my current configuration, by running telnet server-IP smtp I get the following error on mail.log warning: SASL: Connect to /var/spool/postfix/private/auth failed: No such file or directory Now, Dovecot is supposed to create the auth socket file, yet it doesn't. I have given the right privileges to the directory private, and even tried creating a auth file manually. The output of postconf -a is cyrus dovecot Am I correct in assuming from this that the package was compiled with SASL support? My dovecot.conf also holds client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } I have tried every solution out there, and am pretty much desperate after a full day of struggling with the issue. Can anybody help me, pretty please?

  Read the article

• Exchange 2007 relay from sendmail, message "Undelivered". Possible reasons?

  - by garlicman

  Note: This is my re-post from Stackoverflow. I've been messing with a test environment for security purposes where a DMZ RHEL5 sendmail server is used as a relay for an Exchange 2007 server. Exchange is working in the environment, I have Vista and XP VMs using Outlook on the Domain to send e-mail to each other. I've been trying to simulate an external internet VM sending an e-mail to the DMZ sendmail relay, which forwards to the Exchange server. Before everyone thinks this is too big a problem/question, I've followed the sendmail/Exchange guides and all I want to know is how I can determine why a relayed message/e-mail in Exchange is "Undelivered". Basically I send a SMTP message to the sendmail server, which relayed to my Exchange. The /var/log/maillog shows the e-mail being relayed to Exchange. Nov 17 13:41:22 externalmailserver sendmail[9017]: pAHIfMuW009017: from=<[email protected]>, size=1233, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA, relay=[10.50.50.1] Nov 17 13:42:17 externalmailserver sendmail[9050]: pAHIfMuW009017: to=<[email protected]>, delay=00:00:55, xdelay=00:00:36, mailer=relay, pri=121233, relay=mailserver.xyz.local. [192.168.1.20], dsn=2.0.0, stat=Sent (<[email protected]> Queued mail for delivery) This is good, but the To never receives the e-mail from Exchange. So I started poking around Exchange. In the "Message Tracking" Troubleshooting Assistant I queried the processed messages and found this: (I had to copy and paste the cells... sorry for the format) 2011/11/17 RECEIVE SMTP <[email protected]> "Undelivered Mail Returned to Sender" [email protected] [email protected] 192.168.100.10 MAILSERVER\DMZ Relay [email protected] I just want to know if anyone has any suggestions on why the DMZ Relay Connector I setup isn't relaying and is instead returning the forwarded e-mail to sender as Undelivered? My Exchange Relay Receive Connector is pretty simple. The Exchange server's FQDN is set as the HELO response, all available IP addresses can receive relayed e-mail, and the IP address of my sendmail server is specifically set as a remote server.

  Read the article

• Windows XP can use a wired network port, but MacBook (OS X) fails on the same port

  - by Dean Hill

  I wired the Cat5 in my house seven years ago. The wired ports have worked fine with both my Windows XP laptop and MacBook. My wireless network also works fine, but I like to use wired occasionally. One of the Cat5 runs wasn't terminated with a jack, so I recently terminated this wire with a port/jack on the wall end and a standard Cat5 plug on the end that plugs into my router. This is the same setup as my other runs. Unfortunately, the MacBook isn't working well with the new wired port. The OS X Network System Preferences show the IP, Subnet, Router, etc., and everything looks fine. A "netstat -ibd" shows no errors or dropped packets. However, when I open a page in Safari, the status says "Contacting 'www.google.com'" and appears to hang. If I wait for a couple minutes, part of the Google page starts to display, but it is still not the full page load. When I use a Windows XP laptop on the same wired port, everything works fine. An internet speed test shows good results and all web pages load fine. A "netstat -e" under Windows shows no errors. I've used a Cat5 tester, and the cable tests fine (wires 1-8 light up in sequence). I've replaced both the port/jack and the connector twice to make sure I wired things correctly. I'd really like this Cat5 to work with the MacBook (and I'm trying to avoid running a new length of cable). Any ideas what the problem could be?

  Read the article

• legit emails in junkbox

  - by acidzombie24

  Hey this is actually a reverse question. My personal email ([email protected]) is winding up in many peoples junkbox and I have no idea why. What may the cause be? Is it because it has the word Entrepreneur (and programmer) in my sig? is it because my first name is unique(european like)? Its driving me crazy. I sent out dozens of business emails a month to people I just meet so its actually hurting me much more then others :( -edit- I also want to mention this is non spam. Typically I email people I meet and say hi or to follow up. I was requested by someone to send him an email so I can test something, so I did and he replied to me 10 days later telling me he found it in his junk, like many others have said to me. -edit- bortzmeyer suggested emailing [email protected] I did and here are the results SPF check: pass DomainKeys check: pass DKIM check: pass Sender-ID check: pass SpamAssassin check: ham ---------------------------------------------------------- SpamAssassin check details: ---------------------------------------------------------- SpamAssassin v3.2.5 (2008-06-10) Result: ham (-2.6 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- -0.0 SPF_PASS SPF: sender matches SPF record -2.6 BAYES_00 BODY: Bayesian spam probability is 0 to 1% [score: 0.0000] 0.0 HTML_MESSAGE BODY: HTML included in message

  Read the article

• Throughput; capacity planning help for C10K like design

  - by z8000

  I am designing a network service in which clients connect and stay connected -- the model is not far off from IRC less the s2s connections. I could use some help understanding how to do capacity planning, in particular with the system resource costs associated with handling messages from/to clients. There's an article that tried to get 1 million clients connected to the same server [1]. Of course, most of these clients were completely idle in the test. If the clients sent a message every 5 seconds or so the system would surely be brought to its knees. But... How do you do less hand-waving and you know, measure such a breaking point? We're talking about messages being sent by a client over a TCP socket, into the kernel, and read by an application. The data is shuffled around in memory from one buffer to another. Do I need to consider memory throughput ("5 GT/s" [2], etc.)? I'm pretty sure I have the ability to measure the basic memory requirements due to TCP/IP buffers, expected bandwidth, and CPU resources required to process messages. I'm a little dim on what I'm calling "thoughput". Help! Also, does anyone really do this? Or, do most people sort of hand-wave and see what the real world offers, and then react appropriately? [1] http://www.metabrew.com/article/a-million-user-comet-application-with-mochiweb-part-3/ [2] http://en.wikipedia.org/wiki/GT/s

  Read the article

• iis 7.5 - WFF and ARR farm management

  - by smackaysmith

  We have two test web farms (IIS 7.5). The Florida web farm has two ARR servers and two content servers. The ARR servers have WFF and NLB installed. The ARR setup uses a shared config located on a file share. The content servers do not have WFF installed. There is one web farm, and it's managed on an ARR server. The Illinois web farm also has two ARR servers and two content servers. ARR servers have WFF and NLB installed, and they use a shared config located on a share. One of the content servers has WFF installed, which makes it the controller; it's also the primary content server. Apparently, Illinois isn't properly configured. From what we've pieced together from various IIS.net articles and this post (http://ruslany.net/2010/07/web-farm-framework-2-0-overview/), the controller should be one of the ARR servers (like our Florida setup). The thing is Florida's controller doesn't have a Primary server nor can you set one of the content servers as Primary. It doesn't have the management piece showing the Trace messages when you click the Servers node (from iis console, Server Farms/FLFarm/Servers http://ruslany.net/wp-content/uploads/2010/07/WebFarm8.png). That management piece does exist in the Illinois farm, but that's a bad configuration. What are we missing that our Florida configuration doesn't have the Primary and Secondary content servers, and the management piece? I have looked for IIS role differences, but there are none.

  Read the article

• Issues with creating a snapshot

  - by Andy Welcomer

  Hello everyone, We have a strange issue when attempting to create a snapshot in one of our regional environments. We have 4 VMs, 2 of them have mulitple VMDKs spread onto different datastores. When a snapshot is created, all the VMDKs (except for the first), seem to vanish. If you look at the properties of the VM, the path to the VMDKS points to the datastore where the primary VMDK is, and the file name is some random garbage. If the snapshot is deleted everything returns to normal. Has anyone ever seen this? I'm using ESX3.5 Thank you in advance. Andy ==============UPDATE============== Here is some more information. I just created a test machine with 7 VMDKs. 1 for the OS. and 6 others for data. All of the VMDKs are in seperate datastores. I take a snapshot of the machine, all of the 6 VMDKs loose their reference to the actual VMDK files. The all point to 64KB VMDK files in the datastore where the OS VMDK is located. These 64KB vmdks didn't exist until the snapshot was taken. When the snapshot is deleted, everything goes back to normal.

  Read the article

• VMware and Windows Activation

  - by Peter M

  Yesterday I installed Slysoft's Virtual CloneDrive in order to mount an iso for some software installation on my host system (XP Pro SP3) This morning I fired up VMware and made a linked clone of an existing XP vm in order to do some software testing. This is the sort of thing that I do all the time, and the base XP vm that I clone was activated a long long time ago. The surprise today was that the newly cloned vm was no longer activated and XP cited major changes in hardware as the reason. I repeated the test with a full clone of the base system and got the same message. I then started up my base vm and it seemed to be activated, yet another vm (which I fully cloned from the base vm a long time ago) now started reporting that XP was not activated. At this point I guessed that Virtual DriveClone might have been the source of my hardware differences so I uninstalled it and rebooted. After this I made a new linked clone and full clone of the base vm and XP did not complain about not being activated. So I seem to be back to where I was before installing Virtual DriveClone with the exception that that one particular XP vm continues to complain about activation (even though 4 or 5 other XP vm's are fat and happy) Now to my questions: Why would adding Virtual CloneDrive to the host system affect XP activation on the vm's? From their point of view I would have thought that the environment had not changed as I had not enabled any new hard drives in their systems. Or is adding a hard drive to the host system enough to upset XP activation? Since this event, one of my fully cloned vm's is still reporting that XP is not activated even though I have removed Virtual CloneDrive. Is there anyway to convince XP that it is on the same system as yesterday? Or are my only options to do an activation or restore the vm from a previous backup?

  Read the article

• OpenBSD logins via SSH seem to be ignoring my configured radius server

  - by Steve Kemp

  I've installed and configured a radius server upon my localhost - it is delegating auth to a remote LDAP server. Initially things look good: I can test via the console: # export user=skemp # export pass=xxx # radtest $user $pass localhost 1812 $secret Sending Access-Request of id 185 to 127.0.0.1 port 1812 User-Name = "skemp" User-Password = "xxx" NAS-IP-Address = 192.168.1.168 NAS-Port = 1812 rad_recv: Access-Accept packet from host 127.0.0.1 port 1812, id=185, Similarly I can use the login tool to do the same thing: bash-4.0# /usr/libexec/auth/login_radius -d -s login $user radius Password: $pass authorize However remote logins via SSH are failing, and so are invokations of "login" started by root. Looking at /var/log/radiusd.log I see no actual log of success/failure which I do see when using either of the previous tools. Instead sshd is just logging: sshd[23938]: Failed publickey for skemp from 192.168.1.9 sshd[23938]: Failed keyboard-interactive for skemp from 192.168.1.9 port 36259 ssh2 sshd[23938]: Failed password for skemp from 192.168.1.9 port 36259 ssh2 In /etc/login.conf I have this: # Default allowed authentication styles auth-defaults:auth=radius: ... radius:\ :auth=radius:\ :radius-server=localhost:\ :radius-port=1812:\ :radius-timeout=1:\ :radius-retries=5:

  Read the article

• debian VM refusing all traffic apart from http

  - by james lewis

  I've got a VM with a fresh install of Debian (wheezy) and I've installed node and mongo on it. The VM is using a bridged network connection so I was expecting to be able to point my host machines browser at the ip address of the Debian VM (port 1337 for my node example or port 28017 for my mongo status page) and see one of the two services (node or mongo). My requests are refused though. As far as I can tell Debian allows all traffic by default and you have to manually configure iptables to drop traffic. I've checked iptables and it says it's setup to allow anything through. It looks like this: root@devbox:/home/jlewis# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination As a test I setup nginx and I was able to get to the nginx landing page from my host no problems so obviously http traffic is allowed. I then set nginx up to forward all traffic upstream to mongo - no problems there, I was able to see the status page. I then did the same for my example node server and again, no problems. So http traffic is fine, but all other traffic is blocked. Anyone know why debian might be refusing all other traffic other than iptables being setup to drop it? EDIT - output from netstat -nltp: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:28017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:51028 0.0.0.0:* LISTEN 1541/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2462/sshd tcp 0 0 127.0.0.1:1337 0.0.0.0:* LISTEN 2794/node tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2274/exim4 tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1510/rpcbind tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2189/nginx tcp6 0 0 :::22 :::* LISTEN 2462/sshd tcp6 0 0 :::45335 :::* LISTEN 1541/rpc.statd tcp6 0 0 ::1:25 :::* LISTEN 2274/exim4 tcp6 0 0 :::111 :::* LISTEN 1510/rpcbind

  Read the article

• CNAME rule being ignored

  - by Ben

  On a server with Plesk installed I have added a CNAME rule pointing from one of the sites subdomains to an external website. I have checked the named configuration for that domain name and it shows the CNAME however the sub domain just points to the default server page and ignores the CNAME rule. Named has been restarted and I've also run the rvmng reconfigure-vhost command. I edited another server to test this, on cPanel, and it works fine. The conf file for the domain: ; *** Ts file is automatically generated by Plesk *** $TTL 86400 @ IN SOA ns.example.com. cf.example1.com. ( 1292946742 ; Serial 10800 ; Refresh 3600 ; Retry 604800 ; Expire 10800 ) ; Minimum example.com. IN NS ns.example.com. ns.example.com. IN A xx.xxx.xxx.xx example.com. IN A xx.xxx.xxx.xx webmail.example.com. IN A xx.xxx.xxx.xx mail.example.com. IN A xx.xxx.xxx.xx beta.example.com. IN A xx.xxx.xxx.xx ftp.example.com. IN CNAME example.com. www.example.com. IN CNAME example.com. login.example.com. IN CNAME socialize.gigya.com. example.com. IN MX 10 webmail.example.com. You can see the CNAME rule in the file but it just gets ignored? Thanks in advance for any help.

  Read the article

• Chrome caching 302 redirects

  - by Thermionix

  I have a php script with is used to rotate banner images on a site. Under Firefox/IE page refreshes will make another request and a different image will be returned. Under Chrome, the request seems to be cached and only opening the page in a new tab will cause it to actually query the script. I believe this used to work in older versions of chrome, I've tried a few different types of redirect codes all with the same result. Any tips? <img class="banner" src="/inc/banner.php" alt=""> ~$ cat /var/www/inc/banner.php <?php header("HTTP/1.1 302 Redirect"); header("Cache-Control: max-age=0, no-cache, no-store, must-revalidate"); //header('HTTP/1.1 307 Temporary Redirect'); //header("expires: none"); //header("expires: max"); //header("Cache-Control: public"); $folder = '../img/banner/'; $exts = 'jpg jpeg png gif'; $files = array(); $i = -1; if ('' == $folder) $folder = './'; $handle = opendir($folder); $exts = explode(' ', $exts); while (false !== ($file = readdir($handle))) { foreach($exts as $ext) { // for each extension check the extension if (preg_match('/\.'.$ext.'$/i', $file, $test)) { // faster than ereg, case insensitive $files[] = $file; // it's good ++$i; } } } closedir($handle); // We're not using it anymore mt_srand((double)microtime()*1000000); // seed for PHP < 4.2 $rand = mt_rand(0, $i); // $i was incremented as we went along header('Location: '.$folder.$files[$rand]); flush(); ?> curl output; ~$ curl -I -k https://example.net/inc/banner.php HTTP/1.1 302 Redirect Server: nginx/1.1.14 Date: Fri, 24 Feb 2012 03:23:46 GMT Content-Type: text/html Connection: keep-alive X-Powered-By: PHP/5.3.10-1ubuntu1 Cache-Control: max-age=0, no-cache, no-store, must-revalidate Location: ../img/banner/2.jpg

  Read the article

< Previous Page | 733 734 735 736 737 738 739 740 741 742 743 744  | Next Page >