Search Results

Search found 8193 results on 328 pages for 'dev ray'.

Page 74/328 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

  • Mounting an attached ebs volume in EC2

    - by David
    I've created an EC2 instance, created an EBS volume, attached it to the running instance, and successfully ssh'ed into my instance. The drive is attached as /dev/sdf Next, I tried mounting the drive by running: mkdir /testName mount -t ext3 /dev/sdf /testName But then I get the error message: mount: wrong fs type, bad option, bad superblock on /dev/sdf, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so What am I doing wrong? Thanks.

    Read the article

  • filesystem mounting problem

    - by user306988
    Hello, A DAS box is attached to my linux box using LSI SCSI HBA. Volume is properly detected on the linux box and filesystem is created using mkfs.ext2 /dev/sdc #No partition table I can not mount the volume using mount/dev/sdc /mnt/temp -t ext3 But I can mount it using mount /dev/sdc /mnt/temp -t ext3 -o loop Can anybody please tell me what "-o loop" option does internally? Has anybody faced this option before? Thanks in advance, prashant

    Read the article

  • Xen DomU on DRBD device: barrier errors

    - by Halfgaar
    I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

    Read the article

  • Nginx Not Passing URL Parameters

    - by jmccartie
    Messing around with Nginx ... for some reason, it looks like none of my URL parameters are being passed. My homepage loads fine, but a URL like "http://mysite.com/more.php?id=101" throws errors, saying that the ID is an undefined index. I'm assuming this is something basic I'm missing in a conf file. Some info: conf.d/virtual.conf server { listen 80; server_name dev.mysite.com; index index.php; root /var/www/dev.mysite.com_html; location / { root /var/www/dev.mysite.com_html; } location ~ \.php(.*)$ { fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME /var/www/wap/dev.mysite.com_html/$fastcgi_script_n ame; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } } Error log: 2009/06/22 11:44:21 [notice] 16319#0: start worker process 16322 2009/06/22 11:44:28 [error] 16320#0: *1 FastCGI sent in stderr: "PHP Notice: Undefined index: id in /var/www/dev.mysite.com_html/more.php on line 10 Thanks in advance.

    Read the article

  • My linux server takes more than an hour to boot. Suggestions?

    - by jamieb
    I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

    Read the article

  • How to restrict user to a particular folder in CentOS 6?

    - by Chris Demetriad
    I will need to create users so developers can log in and clone/pull/push changes/repositories from a github like platform. I've managed to add a user (using the root) to this CentOS machine; I now have this line in /etc/passwd: chris:x:32008:32010::/home/chris/public_html:/bin/bash ..and this in /etc/shadow: chris:$1$ruUeLtTu$onAY2hdu1J.UmHajEIlmR.:15385:0:99999:7::: I am able to SSH the server, I have permission to create a folder and I guess that should be enough. But I am able to see other files and folders outside public_html. How can I actually restrict the user to a particular directory so he can't "cd out" of his folder? Update: root@echo [~]# ls -ld /home/moove drwx--x--x 21 moove moove 4096 Mar 22 16:16 /home/moove/ root@echo [~]# ls -ld /home/moove/public_html drwxr-x--- 11 moove nobody 4096 Mar 27 11:29 /home/moove/public_html/ root@echo [~]# ls -ld /home/moove/public_html/dev drwxr-x--- 12 moove nobody 4096 Mar 27 14:47 /home/moove/public_html/dev/ root@echo [~]# ls -ld /home/moove/public_html/dev/arsenal drwxr-xr-x 3 arsenal moove 4096 Mar 27 14:53 /home/moove/public_html/dev/arsenal/

    Read the article

  • How to run Event Viewer as another user?

    - by Ray Cheng
    I want to create a shortcut to run Windows Event Viewer as another user, but the following doesn't seem to work. Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:\Windows\System32>C:\Windows\System32\runas.exe /noprofile /user:domain\username "C:\Windows\system32\eventvwr.msc /s" Enter the password for domain\username: Attempting to start C:\Windows\system32\eventvwr.msc /s as user "dnr\adm_rche490" ... RUNAS ERROR: Unable to run - C:\Windows\system32\eventvwr.msc /s 193: C:\Windows\system32\eventvwr.msc /s is not a valid Win32 application. But if I create the shortcut without the runas part, it works but with the current logon user. What am I doing wrong?

    Read the article

  • Building NanoBSD inside a jail

    - by ptomli
    I'm trying to setup a jail to enable building a NanoBSD image. It's actually a jail on top of a NanoBSD install. The problem I have is that I'm unable to mount the md device in order to do the 'build image' part. Is it simply not possible to mount an md device inside a jail, or is there some other knob I need to twiddle? On the host /etc/rc.conf.local jail_enable="YES" jail_mount_enable="YES" jail_list="build" jail_set_hostname_allow="NO" jail_build_hostname="build.vm" jail_build_ip="192.168.0.100" jail_build_rootdir="/mnt/zpool0/jails/build/home" jail_build_devfs_enable="YES" jail_build_devfs_ruleset="devfsrules_jail_build" /etc/devfs.rules [devfsrules_jail_build=5] # nothing Inside the jail [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# sysctl security.jail security.jail.param.cpuset.id: 0 security.jail.param.host.hostid: 0 security.jail.param.host.hostuuid: 64 security.jail.param.host.domainname: 256 security.jail.param.host.hostname: 256 security.jail.param.children.max: 0 security.jail.param.children.cur: 0 security.jail.param.enforce_statfs: 0 security.jail.param.securelevel: 0 security.jail.param.path: 1024 security.jail.param.name: 256 security.jail.param.parent: 0 security.jail.param.jid: 0 security.jail.enforce_statfs: 1 security.jail.mount_allowed: 1 security.jail.chflags_allowed: 1 security.jail.allow_raw_sockets: 0 security.jail.sysvipc_allowed: 0 security.jail.socket_unixiproute_only: 1 security.jail.set_hostname_allowed: 0 security.jail.jail_max_af_ips: 255 security.jail.jailed: 1 [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mdconfig -l md2 md0 md1 md0 and md1 are the ramdisks of the host. bsdlabel looks sensible [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# bsdlabel /dev/md2s1 # /dev/md2s1: 8 partitions: # size offset fstype [fsize bsize bps/cpg] a: 1012016 16 4.2BSD 0 0 0 c: 1012032 0 unused 0 0 # "raw" part, don't edit newfs runs ok [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# newfs -U /dev/md2s1a /dev/md2s1a: 494.1MB (1012016 sectors) block size 16384, fragment size 2048 using 4 cylinder groups of 123.55MB, 7907 blks, 15872 inodes. with soft updates super-block backups (for fsck -b #) at: 160, 253184, 506208, 759232 mount fails [root@build /usr/obj/nanobsd.PROLIANT_MICROSERVER]# mount /dev/md2s1a _.mnt/ mount: /dev/md2s1a : Operation not permitted UPDATE: One of my colleagues pointed out There are some file systems types that can't be securely mounted within a jail no matter what, like UFS, MSDOFS, EXTFS, XFS, REISERFS, NTFS, etc. because the user mounting it has access to raw storage and can corrupt it in a way that it will panic entire system. From http://www.mail-archive.com/[email protected]/msg160389.html So it seems that the standard nanobsd.sh won't run inside a jail while it uses the md device to build the image. One potential solution I'll try is to chroot from the host into the build jail, rather than jexec a shell.

    Read the article

  • How do I usb tether my Cyanogen modded G1's internet connection to my Toshiba Tecra 8000 running Xub

    - by atticus
    I have usb-tethering enabled in my phone. It works fine with Vista. When I plug my phone into my Tecra 8000 laptop running Xubuntu, dmesg shows: "usb 1-1: new full speed USB device using uhci_hcd and address 8". I see that the OS has detected it as a storage device, but I can't get it to function correctly as a network device. /dev/us* shows no usb0, but it does show /dev/usbdev1.1_ep00 /dev/usbdev1.1_ep81 /dev/usbdev1.8_ep00 ... usbdev1.8_ep83.

    Read the article

  • OpenVPN - Windows 8 to Windows 2008 Server, not connecting

    - by niico
    I have followed this tutorial about setting up an OpenVPN Server on Windows Server - and a client on Windows (in this case Windows 8). The server appears to be running fine - but it is not connecting with this error: Mon Jul 22 19:09:04 2013 Warning: cannot open --log file: C:\Program Files\OpenVPN\log\my-laptop.log: Access is denied. (errno=5) Mon Jul 22 19:09:04 2013 OpenVPN 2.3.2 x86_64-w64-mingw32 [SSL (OpenSSL)] [LZO] [PKCS11] [eurephia] [IPv6] built on Jun 3 2013 Mon Jul 22 19:09:04 2013 MANAGEMENT: TCP Socket listening on [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:04 2013 Need hold release from management interface, waiting... Mon Jul 22 19:09:05 2013 MANAGEMENT: Client connected from [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'state on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'log all on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold off' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold release' Mon Jul 22 19:09:05 2013 Socket Buffers: R=[65536->65536] S=[65536->65536] Mon Jul 22 19:09:05 2013 UDPv4 link local: [undef] Mon Jul 22 19:09:05 2013 UDPv4 link remote: [AF_INET]66.666.66.666:9999 Mon Jul 22 19:09:05 2013 MANAGEMENT: >STATE:1374494945,WAIT,,, Mon Jul 22 19:10:05 2013 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) Mon Jul 22 19:10:05 2013 TLS Error: TLS handshake failed Mon Jul 22 19:10:05 2013 SIGUSR1[soft,tls-error] received, process restarting Mon Jul 22 19:10:05 2013 MANAGEMENT: >STATE:1374495005,RECONNECTING,tls-error,, Mon Jul 22 19:10:05 2013 Restart pause, 2 second(s) Note I have changed the IP and port no (it uses a non-standard port for security reasons). That port is open on the hardware firewall. The server logs are showing a connection attempt from my client: TLS: Initial packet from [AF_INET]118.68.xx.xx:65011, sid=081af4ed xxxxxxxx Mon Jul 22 14:19:15 2013 118.68.xx.xx:65011 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) How can I problem solve this & find the problem? Thx Update - Client config file: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. ;proto tcp proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. remote 00.00.00.00 1194 ;remote 00.00.00.00 9999 ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. ;remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nobody # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\my-laptop.crt" key "C:\\Program Files\\OpenVPN\\config\\my-laptop.key" # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 Server config file: ################################################# # Sample OpenVPN 2.0 config file for # # multi-client server. # # # # This file is for the server side # # of a many-clients <-> one-server # # OpenVPN configuration. # # # # OpenVPN also supports # # single-machine <-> single-machine # # configurations (See the Examples page # # on the web site for more info). # # # # This config should work on Windows # # or Linux/BSD systems. Remember on # # Windows to quote pathnames and use # # double backslashes, e.g.: # # "C:\\Program Files\\OpenVPN\\config\\foo.key" # # # # Comments are preceded with '#' or ';' # ################################################# # Which local IP address should OpenVPN # listen on? (optional) ;local 00.00.00.00 # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. std 1194 port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\server.crt" key "C:\\Program Files\\OpenVPN\\config\\server.key" # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh "C:\\Program Files\\OpenVPN\\config\\dh2048.pem" # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). ;push "redirect-gateway def1 bypass-dhcp" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 208.67.222.222" ;push "dhcp-option DNS 208.67.220.220" # Uncomment this directive to allow differenta # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nobody # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I have changed IP's for security

    Read the article

  • How to maintain the log source host using logstash

    - by Ray Rodriguez
    I am following the steps in this blog to set up rsyslog + logstash + graylog2 and I can't figure out how to replace the @source_host attribute in logstash using the mutate - replace filter. In the exmaple the author replaces his @source_host with a string value but I'd like to use the actual value that is parsed from in this case a syslog. mutate { type => loc1 replace => ["@source_host", "loc1"] } mutate { type => loc2 replace => ["@source_host", "loc2"] } How do I actually maintain the original source host in my logs?

    Read the article

  • How to change the sender of admin mails on a Linux server

    - by Cédric Girard
    Hi, I am sure it is a dumb question, but I want to change the sender of mails sended by my Linux server (centos 5). All mails sent to user "dev" are forwarded via a /home/dev/.forward file, with this sender : [email protected]. host.mydomain.fr is the hostname of this server, but it's an internal server and it does not even have a public IP. How to have a sender like [email protected]? I try to change the "official domain name" (line begining by "Dj" but it change nothing). Regards Cédric

    Read the article

  • /var/lib/ureadahead/debugfs using up disk space

    - by Keyo
    Running Ubuntu 10.04 and nearly all my drive space is gone. # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 7.3G 6.6G 327M 96% / none 245M 240K 244M 1% /dev none 249M 0 249M 0% /dev/shm none 249M 340K 249M 1% /var/run none 249M 0 249M 0% /var/lock none 249M 0 249M 0% /lib/init/rw /dev/sda1 228M 34M 183M 16% /boot Of course it's not mounted. I read that chmod 0 /sbin/debugfs could fix the problem, but now it just won't mount despite changing the permission to 777. This is a VM running on VirtualBox. I have done a file system check which ran fine. What is this directory and how can I remove it from the system?

    Read the article

  • Help creating image from LVM

    - by jackhab
    I need to duplicate CentOS hard drive image for multiple stations. The HD has the following layout: Disk /dev/sdb: 250GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 107MB 107MB primary ext3 boot 2 107MB 250GB 250GB primary lvm I saved /dev/sdb1 to file with fsarchiver but for sdb2 I get: /fsarchiver savefs an2.fsa /dev/sdb2 oper_save.c#1006,filesystem_mount_partition(): can't detect and mount filesystem of partition [/dev/sdb2], cannot continue. removed an2.fsa Although fsarchiver probe simple correctly detects sdb2 as LVM2_member. Is fsarchiver correct tool for this job? What's wrong? I'm on Ubuntu 9.1 with fsarchiver 0.6.8 and lvm tools installed. Thanks.

    Read the article

  • Help creating image from LVM

    - by jackhab
    I need to duplicate CentOS hard drive image for multiple stations. The HD has the following layout: Disk /dev/sdb: 250GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 107MB 107MB primary ext3 boot 2 107MB 250GB 250GB primary lvm I saved /dev/sdb1 to file with fsarchiver but for sdb2 I get: /fsarchiver savefs an2.fsa /dev/sdb2 oper_save.c#1006,filesystem_mount_partition(): can't detect and mount filesystem of partition [/dev/sdb2], cannot continue. removed an2.fsa Although fsarchiver probe simple correctly detects sdb2 as LVM2_member. Is fsarchiver correct tool for this job? What's wrong? I'm on Ubuntu 9.1 with fsarchiver 0.6.8 and lvm tools installed. Thanks.

    Read the article

  • Add a small RAID card? Will it help overall stability and performance of my nine hard drives?

    - by Ray
    Hi, Will I get any extra genuine added performance and RAID stability if I insert a basic RAID card into a PCI-E x1 slot? I am considering the Adaptec 1220SA - 2 port SATA , pci-express (1x) , raid 0/1. Ok it only supports two SATA drives. Purpose is to help support the eight internal hard drives (1TB each), a DVD drive and an external e-SATA connected 2TB hard drive - by dealing with two of the internal hard drives. My current configuration of eight internal 1TB Barracuda (7200.12) SATA hard drives, one external 2TB SATA Western Digital Green Drive (e-SATA) and one DVD drive can already be supported by the Intel P55 & JMicron controllers on the ASUS motherboard : the Intel P55 (controls six HDD; configured as three x RAID 1), and the JMicron (controls two HDD as one RAID 1, as well as the DVD drive and the external SATA drive via the motherboard's e-SATA port (controlled by the JMicron)). Bigger picture details : I have an ASUS motherboard designed for the LGA1156 type processor and it includes the Intel P55 Express Chipset and JMicron. I am using the Intel Core i7-870 processor, and have 8GB DDR3 (1333) memory (four x 2GB Corsair DIMMs). Enough overall power. The power supply is more than sufficicient for the system. Corsair AX850. The system will never need the full 850 watts (future : second graphics card). The RAID card would provide hardware RAID 1 for two of the eight intrnal drives. It would either reduce the load on : the Intel P55 firmware RAID support, or replace the JMicron controller's RAID 1 set. I am busy installing the above configuration using Windows 7 Ultimate 64-bit as the OS. The RAID card is a last minute addition to the plan. Is it worth spending the extra R700 - R900 on the Adaptec 1220SA, or equivalent RAID card? I cannot afford to spend yet another R2000 - R3000 on a RAID card that would support many SATA2 hard drives, with a better RAID, example the RAID 5. My Issue & assumption : I am trusting that the Intel P55 chipset can properly handle six drives, configured as three * RAID 1. I am assuming that the JMicron can handle, using its RED SATA ports, one RAID-1 (two HDDs). The DVD drive connects to the JMicron optical SATA port 1 (white port 1). White port 2 is not used. The e-SATA connection is from the JMicron straight to, and through the motherboard - to an on-board (rear panel) e-SATA port. Am I being a little hopeful in only using the on-board Intel P55 and the JMicron? Is it a waste of money to install a RAID card that handles two SATA2 drives? OR Is it wisdom to take the pressure a little off the Intel P55? Obviously I am interested in data security, hence RAID 1, not RAID Zero. RAID 5 would be nice. The CPU, Intel Core i7-870 will provide the clout. Context to nine drives : I am using virtualisation with Windows 7 Ultimate. Bootable VMs. The operating system gets a mirror. Loaded apps gets a mirror. The current design data is kept in another mirror and Another mirror is back-up one and / or VM territory. Then the external 2TB drive (via e-SATA) is the next layer of data security and then finally, I use off-site data security. Thanks.

    Read the article

  • How do I mount a raid disk

    - by Devator
    So I screwed up my grub.conf file on a CentOS system and I'm in recovery right now (it's only a test dedicated server). My disks are /dev/sda1 and /dev/sdb1 (RAID 1). Now I need to mount /dev/sda1 and make changes to the grub file, however those changed need to be reflected on the second disk aswell. How do I mount these RAID disks? I can mount one using mount -t ext3however it will damage the RAID array.

    Read the article

  • Creating a USB stick for installing centos 6.x using DVD1 and DVD2 iso files

    - by user250563
    First, we create 2 partitions on the USB stick that is let's say 16GB. first partition is let's say only 1GB and the second partition is the rest of what is available. after we "w" write the changes, the USB now has 2 partitions. 1 is 1GB 1 is more than 14GB so , we have... sdb1 and sdb2 now. now we need to turn these partitions into filesystems some say i should run these commands after those procedures. mkfs.vfat -F 32 /dev/sdb1 mkfs.ext3 /dev/sdb2 but some web pages recommend using: mkfs.vfat -n BOOT /dev/sdb1 mkfs.ext2 -m 0 -b 4096 -L DATA /dev/sdb2 which is it? so let's say the DVDs are called: CentOS-6.4-x86_64-bin-DVD1.iso CentOS-6.4-x86_64-bin-DVD2.iso so we make a directory: mkdir -p /mnt/dvd1 and then mount it: mount -o loop CentOS-6.4-x86_64-bin-DVD1.iso /mnt/dvd1 and i suppose we don't make a directory for dvd2 and we don't have to mount it ? at this point i do not know what should be done. but i think this step might be next: we make the USB bootable by finding the file named mbr.bin and then moving it to there via these commnad. dd conv=notrunc bs=440 count=1 if=/usr/lib/syslinux/mbr.bin of=/dev/sdb parted /dev/sdb set 1 boot on in other words we are "dd-ing it to 'sdb' not sdb1' or 'sdb2'. and then we use parted to set the boot to on for sdb so far everything looks good? here is the confusing parts.. how exactly do i move these iso files to the usb drive? EVERYTHING BELOW IS A GUESS. so at this point i should copy the folder /mnt/dvd1/isolinux to usb's sdb1 or sdb2 ? rename it to syslinux ? and then inside this syslinux folder there will be a file called... isolinux.cfg ? which should be renamed to syslinux.cfg ? and then copy the contents of /mnt/dvd1/images/* to USB's sdb2 ? but i think i am also suppose to copy and paste the both CentOS-6.4-x86_64-bin-DVD1.iso CentOS-6.4-x86_64-bin-DVD2.iso somewhere into this USB's sdb2 partition, correct ? almost like a drag and drop kind of a thing? or do they go into any folders ? centos' own web site has some instructions but those instructions do not work. http://wiki.centos.org/HowTos/InstallFromUSBkey i once got this working but things got ruined, i have to do it again and this time take notes.

    Read the article

  • Resizing Partitions on Live RHEL/cPanel Server

    - by Timothy R. Butler
    I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

    Read the article

  • BTrFS crashhhh?

    - by bumbling fool
    I create a new BTrFS raid10 file system using two 250GB drives and the second partition on a third 80GB drive. I create a subvol and snapshot. I mount the snapshot and start copying 8GB of data to it. It gets to around 1GB and the Desktop disappears and what looks like a non interactive terminal comes up with dump/crash information. I don't have a camera handy or I'd take a picture and post it. It basically looks like stack trace info. CTRL-ALT F7 will eventually bring back the Desktop though but the entire BTrFS portion of the OS is hung and non responsive until I reboot. I've reformated and reproduced this problem 3 times now and I'm about to give up :( I realize it is possible this problem is not entirely BTrFS' fault because I'm on natty which is still alpha. More granular details in case I'm an idiot: 1) Create FS: sudo mkfs.btrfs -m raid10 -d raid10 /dev/sda2 /dev/sdb /dev/sdc 2) Initial temporary mount: mkdir /btrfs && sudo mount -t btrfs /dev/sda2 /btrfs 3) Create subvol btrfs s c /btrfs/vm 4) Create initial snapshot: (optional) btrfs s sn /btrfs/cantremember.snap.something 5)unmount /btrfs and mount /btrfs/vm sudo mount -t btrfs -o subvol=vm /dev/sda2 /btrfs/vm 6) Copy data to subvolume. 7) Balance data across drives: (optional) btrfs f bal <path> (never get to this step 7...) Am I doing something wrong?

    Read the article

  • Trouble with Debian Lenny and Sphinx

    - by Ando
    I've very basic understanding of linux systems, but I've a server which was setup a while ago to host some web apps. Recently I decided to test out and implement Sphinx but unfortunately I cant get the install to work. I'm running a Debian Lenny distro and when I try to install sphinx it says - checking MySQL include files... configure: error: missing include files. ****************************************************************************** ERROR: cannot find MySQL include files. Check that you do have MySQL include files installed. The package name is typically 'mysql-devel'. If include files are installed on your system, but you are still getting this message, you should do one of the following: 1) either specify includes location explicitly, using --with-mysql-includes; 2) or specify MySQL installation root location explicitly, using --with-mysql; 3) or make sure that the path to 'mysql_config' program is listed in your PATH environment variable. To disable MySQL support, use --without-mysql option. ****************************************************************************** I do have mysql 5.1 installed but I can't find the include files, AND one more thing.. I read around the net that I probably need libmysqlclient15-dev but when I try to install that using apt-get i receive the following error. The following packages were automatically installed and are no longer required: libxcb-aux0 libts-0.0-0 libxcb-atom1 ttf-dejavu-extra hunspell-en-us g++-4.3 libmysql++3 libnspr4-0d libdirectfb-1.0-0 libxcb-event1 libasound2 libstdc++6-4.3-dev libhunspell-1.2-0 ttf-dejavu libmozjs2d conkeror-spawn-process-helper libnss3-1d Use 'apt-get autoremove' to remove them. The following NEW packages will be installed: libmysqlclient15-dev 0 upgraded, 1 newly installed, 0 to remove and 276 not upgraded. Need to get 7590 kB of archives. After this operation, 26.3 MB of additional disk space will be used. WARNING: The following packages cannot be authenticated! libmysqlclient15-dev Install these packages without verification [y/N]? Y Err http://ftp.us.debian.org/debian/ lenny/main libmysqlclient15-dev amd64 5.0.51a-24+lenny5 404 Not Found [IP: 35.9.37.225 80] Err http://security.debian.org/ lenny/updates/main libmysqlclient15-dev amd64 5.0.51a-24+lenny5 404 Not Found [IP: 149.20.20.6 80] Failed to fetch http://security.debian.org/pool/updates/main/m/mysql-dfsg-5.0/libmysqlclient15-dev_5.0.51a-24+lenny5_amd64.deb 404 Not Found [IP: 149.20.20.6 80] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Can you help me out by suggesting how to install the required packages and run the Sphinx.

    Read the article

  • Accessing Virtual Host from outside LAN

    - by Ray
    I'm setting up a web development platform that makes things as easy as possible to write and test all code on my local machine, and sync this with my web server. I setup several virtual hosts so that I can access my projects by typing in "project" instead of "localhost/project" as the URL. I also want to set this up so that I can access my projects from any network. I signed up for a DYNDNS URL that points to my computer's IP address. This worked great from anywhere before I setup the virtual hosts. Now when I try to access my projects by typing in my DYNDNS URL, I get the 403 Forbidden Error message, "You don't have permission to access / on this server." To setup my virtual hosts, I edited two files - hosts in the system32/drivers/etc folder, and httpd-vhosts.conf in the Apache folder of my WAMP installation. In the hosts file, I simply added the server name to associate with 127.0.0.1. I added the following to the http-vhosts.conf file: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot "c:/wamp/www/ladybug" ServerName ladybug ErrorLog "logs/your_own-error.log" CustomLog "logs/your_own-access.log" common </VirtualHost> <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot "c:/wamp/www" ServerName localhost ErrorLog "logs/localhost-error.log" CustomLog "logs/localhost-access.log" common </VirtualHost> Any idea why I can't access my projects from typing in my DYNDNS URL? Also, is it possible to setup virtual hosts so that when I type in http://projects from a random computer outside of my network, I access url.dyndns.info/projects (a.k.a. my WAMP projects on my home computer)? Help is much appreciated, thanks!

    Read the article

  • Clonezilla is not able to clone a RAID 1 disk

    - by Adrian
    I have a HP Server DL320 G5. There are two SATA hard disks configured as RAID 1 through HP embedded RAID controller. Server OS is running GNU/Linux (Fedora) Server booted up with clonezilla live CD. The image will be stored on a NAS connected through NFS. Clonezilla could mount the NFS share and could see the two hard disks /dev/sda and /dev/sdb. I selected /dev/sda for disk cloning. However I could not see the cloning progress and got straight into a prompt for reboot, poweroff, command line I tried to select /dev/sdb but the same issue.

    Read the article

  • VLC Audio Problems in Windows 7

    - by Vijay Dev
    When using VLC in my Windows 7 (RC), the audio works only if my head phones are connected. Without the head phones, the audio is not heard at all. Other players deliver the audio perfectly. Is this caused by some incorrect preferences ?

    Read the article

  • I need a server or service that reroutes DNS requests

    - by Relentim
    We have two external servers, Dev and Prod. We are a software house and in the code we have a subdomain metrics.company.com that points to Prod. Development is continuous and our internal and external developers and testers will need to switch from Dev to Prod and back again. It is not an option to have a different sub domain in the code during development and change this for production. The way we wish to switch between Dev and Prod is to use DNS. We need a public DNS server that behaves normally apart from routing metrics.company.com to Dev. The users will be able to swap their DNS back and forward to hit the different servers. What is the easiest way to do this? Is there a company that hosts this service or am I going to have to rent a server and set it up myself? Any help would be much appreciated.

    Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >