Search Results

Search found 25098 results on 1004 pages for 'usb network adapter'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 74/1004 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

  • Network Sniffing and Hubs

    - by Chris_K
    This will likely seem naive to the experts... but it has been on my mind lately. For years I've been using ntop and a cheap 4 port hub to sniff client networks to determine who's doing what -- and how much. Great way to see what's going on when they call and say "Geeze, the network seems really slow today." No need to bring in a managed switch (or access the existing one) and no need to configure spanning or mirroring. I just drop in the hub inline where I want to measure. Lately I noticed it is just about impossible to buy a real honest-to-goodness hub anymore. While looking for a new one, I had someone tell me that I should be sure to get a full-duplex hub or I'd only be seeing half the traffic when I monitor. Really? I've been using a crusty old Netgear DS104 all this time. No clue if it is half or FD. Have I really been understating my measurements? I'm just not bright enough about the physical layer to really know... Side note: Just ordered a Dualcomm Ethernet Switch TAP as a hub replacement. Seems like a nifty gadget. Any notes or tips about it would be welcome in the comments :-)

    Read the article

  • How to stop my wireless adapter from received dhcp from router (windows)

    - by baobeiii
    Hi, I have a windows 7 computer which is connected via vpn to an OpenVpn server which happens to be in another country. I have all internet traffic being routed from my computer through the vpn to the server. However dns queries are not going through the vpn, but are instead going directly to my isp's dns via a route outside of the vpn tunnel. This is happening because my wireless adapter is configured to obtain DNS server address automatically. The router that stands between my computer and the internet happens to have a DCHP server running on it that is assinging my computer with the DNS addresses of the isp. The issue is, i haven't been able to stop my wireless adapter on my computer from receiving the dns settings from the router. I've tried selecting 'use the following dns server addresses' and then just leaving them blank, but ipconfig /all shows me that this hasn't worked and i'm still getting dns form the router. So is there any way to completely stop my windows wireless adapter from receiving these settings from the router? I have the OpenVpn server pushing to my computer's tun adapter the dns that it should be using. I'd rather solve this in a way that doesn't involve disabling the dhcp server on the router or fiddling with the router. The reason is i'm on a laptop and i want my vpn to not leak dns even when i'm out, for example in wireless hotspots. I know if i could just force the wireless adapter to ignore the router's dhcp server then my dns queries would go through the tunnel to the dns address pushed by the OpenVpn server. Sorry, i know thats long winded, if you have any idea's please do tell me. Thanks and merry xmas.

    Read the article

  • Designing a persistent asynchronous TCP protocol

    - by dogglebones
    I have got a collection of web sites that need to send time-sensitive messages to host machines all over my metro area, each on its own generally dynamic IP. Until now, I have been doing this the way of the script kiddie: Each host machine runs an (s)FTP server, or an HTTP(s) server, and correspondingly has a certain port opened up by its gateway. Each host machine runs a program that watches a certain folder and automatically opens or prints or exec()s when a new file of a given extension shows up. Dynamic IP addresses are accommodated using a dynamic DNS service. Each web site does cURL or fsockopen or whatever and communicates directly with its recipient as-needed. This approach has been suprisingly reliable, however obvious issues have come up and the situation needs to be addressed. As stated, these messages are time-sensitive and failures need to be detected within minutes of submission by end-users. What I'm doing is building a messaging protocol. It will run on a machine and connection in my control. As far as the service is concerned, there is no distinction between web site and host machine -- there is only one device sending a message to another device. So that's where I'm at right now. I've got a skeleton server and a skeleton client. They can negotiate high-quality authentication and encryption. The (TCP) connection is persistent and asynchronous, and can handle delimited (i.e., read until \r\n or whatever) as well as length-prefixed (i.e., read exactly n bytes) messages. Unless somebody gives me a better idea, I think I'll handle messages as byte arrays. So I'm looking for suggestions on how to model the protocol itself -- at the application level. I'll mostly be transferring XML and DLM type files, as well as control messages for things like "handshake" and "is so-and-so online?" and so forth. Is there anything really stupid in my train of thought? Or anything I should read about before I get started? Stuff like that -- please and thanks.

    Read the article

  • Intel Network Connection: This device cannot start. (Code 10)

    - by harryuser
    I have a Intel® Desktop Board DP55KG (see http://www.intel.com/products/desktop/motherboards/DP55KG/DP55KG-overview.htm), which has a Intel 82578DC Gigabit Network Connection on board. Additionally, I have a Intel PRO/1000 PT Dual Port Server Adapter in a PCI express slot and I am running Windows 7 Professional 32-bit. Also I am running with Intels latest network driver, in the 82578DC questions this means 11.6.92.0 with driver date 2010.04.12. The problem I am having is that the Intel 82578DC Gigabit Network Connection will not start on boot with the following message: "This device cannot start. (Code 10)". Disabling and then enabling the device after boot makes the network connection work again without any problems, but as soon as I reboot the problem occurs again. Any suggestion how to fix this? I have seen this problem on another Intel S3420GP board as well in Windows 7 that is.

    Read the article

  • USB Serial cable with CDC support

    - by Harsha
    Hi All, I bought a USB to Serial cable which claims to be CDC compliant. But the bInterfaceClass value in interface descriptor is 0xFF(which is vendor specific). I was expecting it to be 0x02 (Communications and CDC control). In the device manager, i found that the drivers being loaded are ser2pl.sys and serenum.sys. I had learnt usbser.sys is the windows CDC driver, but it was not loaded for my cable. I am pretty much new to this CDC, so i have following questions 1.Does this indicate that the cable is not CDC compliant 2.Can i make this cable CDC compliant (since CDC is a driver functionality), by loading usbser.sys. If yes how?

    Read the article

  • sql exception when transferring project from usb to c:\

    - by jello
    I'm working on a C# windows program with Visual Studio 2008. Usually, I work from school, directly on my usb drive. But when I copy the folder on my hard drive at home, an sql exception is unhandled whenever I try to write to the database. it is unhandled at the conn.Open(); line. here's the exception unhandled Database 'L:\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' already exists. Choose a different database name. Cannot attach the file 'C:\Documents and Settings\Administrator\My Documents\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' as database 'PatientMonitoringDatabase'. it's weird, because my connection string says |DataDirectory|, so it should work on any drive... here's my connection string: string connStr = "Data Source=.\\SQLEXPRESS;AttachDbFilename=|DataDirectory|\\PatientMonitoringDatabase.mdf; " + "Initial Catalog=PatientMonitoringDatabase; " + "Integrated Security=True"; what's going on here?

    Read the article

  • sql exception when transferring project from usb to c:\

    - by jello
    I'm working on a C# windows program with Visual Studio 2008. Usually, I work from school, directly on my usb drive. But when I copy the folder on my hard drive at home, an sql exception is unhandled whenever I try to write to the database. it is unhandled at the conn.Open(); line. here's the exception unhandled Database 'L:\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' already exists. Choose a different database name. Cannot attach the file 'C:\Documents and Settings\Administrator\My Documents\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' as database 'PatientMonitoringDatabase'. it's weird, because my connection string says |DataDirectory|, so it should work on any drive... here's my connection string: string connStr = "Data Source=.\\SQLEXPRESS;AttachDbFilename=|DataDirectory|\\PatientMonitoringDatabase.mdf; " + "Initial Catalog=PatientMonitoringDatabase; " + "Integrated Security=True";

    Read the article

  • Recover backup copy of a ubuntu linux installation on a usb stick using dd

    - by Werner
    Hi, I installed Ubuntu 10.04 on a usb stick in persistent install mode. So I could boot the laptop or my desktop computer with the stick, at boot time. Once I needed the 8GB stick for another purposes so I thought about coyping it to my desktop doing from mac os x: dd if=/dev/disks3s of=/Users/jack/Desktop/usb_copy Now I am trying to do the opposite, after having used the stick, which was formatted to NTFS, just doing dd if=/Users/jack/Desktop/usb_copy of=/dev/disks3s but although I can see that almost of the files are there, I can not boot again. IT is also strange the the file permissions are kind of strange, something like _user What can I do ? Thanks

    Read the article

  • Capturing USB Plug/Unplug events in Firemonkey

    - by radsdau
    [RAD Studio XE3 / C++] I have a FMX project running in Windows only at this stage, but I need to detect events when USB devices are connected and disconnected. I have a similar VCL app that can do this fine, but the Application-HookMainWindow is not exposed in FMX (only VCL). Is there an elegant way to handle this? Or do I have to hack some VCL stuff into my FMX app to make that work? I'd imagine I have to abstract it so I can support other platforms down the track. For the meantime though I need to get the Windows solution working. If the 'VCL hack' thing is required, how would I reference the vcl::Forms::Application from within my Fmx app? Cheers.

    Read the article

  • USB flash drive serial number specification

    - by clyfe
    I retrieve a USB flash drive serial number by means of ioctl HDIO_GET_IDENTITY as described here. Yet, for some flash drives there is no serial (for example my SanDisk Cruzer). Why some drives don not return a serial number? a) HDIO_GET_IDENTITY not implemented in driver ? b) They just don't have one ? c) Other ? (what?) Is there a specification (like IEEE) that describes where and how the serial number is stored inside the flash drive?

    Read the article

  • Specifying network settings during SLES 11 auto installation

    - by banjer
    I'm setting up an autoinst.xml file for auto-installing SLES 11. I get prompted for the various interface settings per below, but they don't seem to stick once the server reboots. I don't think I have the xml defined correctly. I'm hoping someone has experience with this. <ask-list> <ask> <path>networking,dns,hostname</path> <question>Enter Hostname (server name)</question> <stage>initial</stage> <default>merkin</default> </ask> <ask> <path>networking,interfaces,interface,0,device</path> <question>Enter the primary ethernet device:</question> <stage>initial</stage> <default>eth0</default> </ask> <ask> <path>networking,interfaces,interface,0,ipaddr</path> <question>Enter the primary IP Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,interfaces,interface,0,netmask</path> <question>Enter the Netmask Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,routing,routes,route,0,gateway</path> <question>Enter the primary Gateway Address:</question> <stage>initial</stage> </ask> </ask-list> The first one for hostname seems to be sticking just fine, but the rest do not. As an alternative, is there a way to stop the autoinstall at the section where you configure the network devices so that the user can take over? I was able to show the partition proposal, but not sure how to do the same with the networking setup.

    Read the article

  • How to program a neural network for chess?

    - by marco92w
    Hello! I want to program a chess engine which learns to make good moves and win against other players. I've already coded a representation of the chess board and a function which outputs all possible moves. So I only need an evaluation function which says how good a given situation of the board is. Therefore, I would like to use an artificial neural network which should then evaluate a given position. The output should be a numerical value. The higher the value is, the better is the position for the white player. My approach is to build a network of 385 neurons: There are six unique chess pieces and 64 fields on the board. So for every field we take 6 neurons (1 for every piece). If there is a white piece, the input value is 1. If there is a black piece, the value is -1. And if there is no piece of that sort on that field, the value is 0. In addition to that there should be 1 neuron for the player to move. If it is White's turn, the input value is 1 and if it's Black's turn, the value is -1. I think that configuration of the neural network is quite good. But the main part is missing: How can I implement this neural network into a coding language (e.g. Delphi)? I think the weights for each neuron should be the same in the beginning. Depending on the result of a match, the weights should then be adjusted. But how? I think I should let 2 computer players (both using my engine) play against each other. If White wins, Black gets the feedback that its weights aren't good. So it would be great if you could help me implementing the neural network into a coding language (best would be Delphi, otherwise pseudo-code). Thanks in advance!

    Read the article

  • Android AVD With GoogleApi, Not Getting Network Connection

    - by Chris
    I am working on a Windows XP Machine. When running AVDs out of Eclipse, I am getting "No Network Connection" when I am plugged into my company's network and using an AVD that was built with the "Google APIs by Google Inc., Android API 7, revision 1". If I use this same AVD (Google API) and connect to the internet through a Verizon Wireless card, the AVD gets an Internet Connection. If I use an AVD built with "SDK Platform Android 2.1, API 7, revision 1", and connect through my company's network, the AVD gets an Internet Connection. Any ideas what might be blocking this? I am guessing it is something in my company's network, but why only with the AVD created with the Google API?

    Read the article

  • How do I usb tether my Cyanogen modded G1's internet connection to my Toshiba Tecra 8000 running Xub

    - by atticus
    I have usb-tethering enabled in my phone. It works fine with Vista. When I plug my phone into my Tecra 8000 laptop running Xubuntu, dmesg shows: "usb 1-1: new full speed USB device using uhci_hcd and address 8". I see that the OS has detected it as a storage device, but I can't get it to function correctly as a network device. /dev/us* shows no usb0, but it does show /dev/usbdev1.1_ep00 /dev/usbdev1.1_ep81 /dev/usbdev1.8_ep00 ... usbdev1.8_ep83. I could just use the wireless tether app for android, but I can't get my Netgear wg511 v2 (made in China) wireless card to work in this laptop either. But that's another post for later.

    Read the article

  • Can you use a USB dongle inside a VMWare ESX Virual Machine?

    - by Keith Sirmons
    Howdy, I need to know if a USB dongle that is required as a license key for a piece of software will accessible from the physical host machine. This will be a small vSphere 4 installation targeting the quick backup and system restore capabilities of VMWare, not specifically HA, so I am not to worried about the virtual machine automatically failing over to another physical machine and the dongle not being accessible. Does ESX have the capability to map a physical USB port or device to a specific Virtual Machine? I believe this is the dongle: Sentinal Superpro USB Dongle by Rainbow Technologies Thank you, Keith

    Read the article

  • My C#.NET application is running slower when the exe is located on the network

    - by leo
    Hi, My C#.NET application is running much slower when the exe is located on the network. And I'm talking about everything, even the graphical dispay is slower. For example: when a form is already loaded, if I unplug my network cable and minimize and maximize the window, it takes a very long time to redraw itself. I'm using framework .NET 3.5 SP1. Any idea on the cause? My hypothesis so far: I'm missing some options when building the app? my corporate antivirus checks more stuff because the exe is on the network the cache of Windows XP SP3 doesn't work the same way when the exe is on the network the server is a Novell server: maybe this does change something ? Thanks for your help! Leo

    Read the article

  • How do I recover missing partition. Windows 8 with recovery USB?

    - by Akbar Ali
    i bought a Samsung laptop with Windows 8 preinstalled. After a year I removed Windows 8 and installed Windows 7. Before removing Windows 8, I made a Windows 8 recovery USB. Now I want to get back my original Windows 8. When I used the USB, it said missing recovery partition or partition has been deleted. Can I install Windows 8 from the internet, and if I use my recovery USB will it activate Windows or not? Or is there any other way to do this task?

    Read the article

  • How can I login to Ubuntu using a USB serial port?

    - by marc
    How can enable remote terminal login into Ubuntu 9.10 using a USB serial port? I created device /dev/ttyUSB0 and i want to allow logins using Hyper-Terminal. I found some resources but they are related to real hardware rs232 ports. I can't find any information about USB converter. So far I have established connection between that USB-serial port and my laptop. I can send text to the port (cp sometext.txt /dev/ttyUSB0) and read it using hyperterminal. What do I need to do to enable logins on this port?

    Read the article

  • How do I usb tether my Cyanogen modded G1's internet connection to my Toshiba Tecra 8000 running Xub

    - by atticus
    I have usb-tethering enabled in my phone. It works fine with Vista. When I plug my phone into my Tecra 8000 laptop running Xubuntu, dmesg shows: "usb 1-1: new full speed USB device using uhci_hcd and address 8". I see that the OS has detected it as a storage device, but I can't get it to function correctly as a network device. /dev/us* shows no usb0, but it does show /dev/usbdev1.1_ep00 /dev/usbdev1.1_ep81 /dev/usbdev1.8_ep00 ... usbdev1.8_ep83.

    Read the article

  • What is the best file system and allocation size for a USB flash drive?

    - by e-t172
    I'm considering using my 4 GB Kingston DataTraveler USB stick to store my Firefox and Thunderbird profiles for my laptop and desktop PCs. I want to maximize performance when using Firefox. The question is: what is the best file system and allocation size for the fastest Firefox profile operation on a USB flash drive? I'm using Windows 7 on both machines and I don't care about compatibility or the drive's lifetime. I just want to maximize performance. I could even use ext2 with the Ext2 IFS driver if that means it'll be faster. I'm assuming (perhaps I'm wrong) that putting a Firefox profile on a USB stick would be a "lots of small files" usage. In that case, it seems that NTFS would perform best, but I'm not sure. Besides I found nothing regarding the best allocation size to use. Considering that the default allocation size is designed for hard drives (which have different characteristics), I'm assuming that the default allocation size is not the best.

    Read the article

  • Fedora12 Slow USB 2.0 Write Speed, ehci_hcd module is missing.

    - by MA1
    I am using Fedora 12, the problem i am facing is USB 2.0 write speed. I have a dual boot system with Window XP and Fedora 12. USB 2.0 write speed in Windows XP is much faster then what i am getting in Fedora 12. After some googling i came to know that ehci_hcd module is missing/not present in my system. ehci_hcd module is neither loaded nor it is present in the available list of modules. Can someone guide me how to fix this issue? Is ehci_hcd have something to do with USB 2.0 write speed or? Should i have to recompile the kernel and add/enable he ehci_hcd module?

    Read the article

  • How can I guess if a USB cable will power my devices?

    - by rsanchez
    I've had problems with one long (4 meter) USB Mini-B to USB Type-A cable not being able to boot a 2.5'' external hard disc due to not supplying enough current. On top of that, the cable used a Type-A to Mini-B adapter for the Mini-B part, which probably made things worse. Three different shorter cables I got around made the hard disk work without extra current, so it was definitively the cable's fault. However, if I plugged the hard disk to the power, and used the long cable just for data it worked. Here is some related information on powering through USB cables: http://www.girr.org/mac_stuff/usb_stuff.html I have not any long cables that don't have an intermediary Type-A to Mini-B adapter to try them out. My question is: is there a way to guess if a cable will provide enough power for charge/disk drive power? Is it related to the length of the cable, to the build quality of the cable, or the fact that uses intermediary adapters?

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >