Search Results

Search found 27819 results on 1113 pages for 'linux intel'.

Page 75/1113 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

  • dynamic routing between openvpn tunnels

    - by pQd
    i'm thinking about using dynamic routing [ OSPF or RIP ] via OpenVPN tunnels. right now i have few offices connected in full mesh, but this is not scalable solution as we add more locations. i would like to avoid situation when plenty of internal traffic is affected if one of two vpn termination points that i plan to use is down. do you have similar configuration working in production? if so - what routing daemon did you use - quagga? something else? did you encounter any problems? thanks!

    Read the article

  • Understanding Linux SCSI queue depths

    - by Troels Arvin
    I'm experimenting with the effects of different SCSI queue depth values on a Dell server running CentOS Linux 5.4 (x86_64). The server has two QLogic QLE2560 FC HBAs connected via multipathing to a storage system. The storage system has allocated two LUNs to the server, each connected through four paths in an active-active-active-active round-robin configuration. All in all, the two LUNs exist as eight /dev/sdX devices, represented by two devices in /dev/mpath. I currently adjust the queue depth values in /etc/modprobe.conf and check the result (after rebooting) by looking in the seventh column of /proc/scsi/sg/devices. Two questions related to that: Is there a way to adjust queue depths without rebooting or unloading the qla2xxx kernel module? E.g., can I echo a new queue depth value into some /proc or /sys-like file to update the queue depth? If I set the queue depth to 128, is that 128 in total for all devices handled by the qla2xxx module?, or 128 for each HBA? (256 in total), or 128 for each of the eight /dev/sdX devices (1024 in toal)?, or 128 for each of the two /dev/mpath/... devices (256 in total)? This is important for me to know so that my server doesn't flood the storage system, affecting other servers connected to it.

    Read the article

  • How to roll-your-own live CD for safe home browsing

    - by user36533
    Hi, I'm interested in booting-off-flash (i.e. like livecd) for more secure online banking at home. -I like system rescue CD, but AFAIK it doesn't have the wifi drivers. (These are convenient) -ubuntu live cd has the wi-fi drivers, but also has a lot of stuff I don't need -I'd like a way to save some basic config settings (e.g. wifi SSID and passphrase), so that wifi works upon startup, i.e. without having to re-enter the settings. What's the best way to 'roll my own slightly-customized boot-from-flash live cd? thanks, bill

    Read the article

  • Attach radeon driver to specific PCI devices?

    - by genpfault
    I have two Radeon cards in this machine, a 6570 and a 6950: lspci | grep VGA: 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Turks [Radeon HD 6570] 02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Cayman PRO [Radeon HD 6950] I'm trying to get VGA passthrough to work with KVM on Debian Wheezy, passing through the 6950 as a secondary video card to a Windows 7 guest. This works fine if I blacklist the radeon kernel module via /etc/modprobe.d/. If I remove the blacklist to run X11 (or even just a KMS console) on the 6570 the radeon module seems to attach to both cards: dmesg | egrep "01:00.0|02:00.0|radeon": pci 0000:01:00.0: [1002:6759] type 0 class 0x000300 pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xefffffff 64bit pref] pci 0000:01:00.0: reg 18: [mem 0xf7e20000-0xf7e3ffff 64bit] pci 0000:01:00.0: reg 20: [io 0xe000-0xe0ff] pci 0000:01:00.0: reg 30: [mem 0xf7e00000-0xf7e1ffff pref] pci 0000:01:00.0: supports D1 D2 pci 0000:02:00.0: [1002:6719] type 0 class 0x000300 pci 0000:02:00.0: reg 10: [mem 0xd0000000-0xdfffffff 64bit pref] pci 0000:02:00.0: reg 18: [mem 0xf7d20000-0xf7d3ffff 64bit] pci 0000:02:00.0: reg 20: [io 0xd000-0xd0ff] pci 0000:02:00.0: reg 30: [mem 0xf7d00000-0xf7d1ffff pref] pci 0000:02:00.0: supports D1 D2 vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=none,locks=none vgaarb: bridge control possible 0000:02:00.0 vgaarb: bridge control possible 0000:01:00.0 pci 0000:01:00.0: Boot video device [drm] radeon kernel modesetting enabled. radeon 0000:01:00.0: setting latency timer to 64 radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used) radeon 0000:01:00.0: GTT: 512M 0x0000000040000000 - 0x000000005FFFFFFF [drm] radeon: 1024M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. radeon 0000:01:00.0: irq 46 for MSI/MSI-X radeon 0000:01:00.0: radeon: using MSI. [drm] radeon: irq initialized. radeon 0000:01:00.0: WB enabled [drm] radeon: ib pool ready. [drm] radeon: power management initialized fbcon: radeondrmfb (fb0) is primary device fb0: radeondrmfb frame buffer device [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on minor 0 radeon 0000:02:00.0: enabling device (0000 -> 0003) radeon 0000:02:00.0: setting latency timer to 64 radeon 0000:02:00.0: VRAM: 2048M 0x0000000000000000 - 0x000000007FFFFFFF (2048M used) radeon 0000:02:00.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF [drm] radeon: 2048M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. radeon 0000:02:00.0: irq 49 for MSI/MSI-X radeon 0000:02:00.0: radeon: using MSI. [drm] radeon: irq initialized. radeon 0000:02:00.0: WB enabled [drm] radeon: ib pool ready. [drm] radeon: power management initialized fb1: radeondrmfb frame buffer device [drm] Initialized radeon 2.12.0 20080528 for 0000:02:00.0 on minor 1 [drm] radeon: finishing device. radeon 0000:02:00.0: ffff88041a941800 unpin not necessary [drm] radeon: ttm finalized pci-stub 0000:02:00.0: claimed by stub pci-stub 0000:02:00.0: irq 49 for MSI/MSI-X This causes the Win7 VM to bluescreen on boot. How can I configure things so that the radeon module only attaches to the 6570 and not the 6950?

    Read the article

  • The People Who Support Linux

    <b>Linux.com: </b>"The Linux Foundation's individual members help to support the work of Linux creator Linus Torvalds and other important activities that advance Linux, while getting a variety of other fun and valuable benefits. The series begins with Matthew Fernandez, a senior application developer based in Sydney, Australia. Matthew has been using Linux since 2001 and just recently became a Linux Foundation member."

    Read the article

  • How to install Archlinux on a acer emachines em350 ?

    - by zillion
    Do a 64 bits version will work better if the cpu is 64 bits capable ? Can I remove all added stuffs on Archbang or CTKArchLive to return to plain Archlinux with openbox that I can configure myself easily, so I can install Archlinux faster ? I tried and installed Arch properly but I need to install the broadcom bcm 4727 driver (b43,wl,sta,open source), which driver do I need and how can I install it by my usb on Archlinux CLI made with base, sudo and wireless_tools only ?

    Read the article

  • SMB from fedora 12 to windows network

    - by Jean
    Hello, I got Fedora 12 samab and samba client and permitted the same via the iptables. For some reason, I cannot seem to browse my windows network. What did I do wrong, and how can I achieve this. Thanks Jean [edit] - I want to browse the windows workgroup [edit] - Set the workgroup name, restarted the smb in the services, can browse network, but only my fedora 12 system is being shown

    Read the article

  • SMB from fedora 12 to windows network

    - by Jean
    Hello, I got Fedora 12 samab and samba client and permitted the same via the iptables. For some reason, I cannot seem to browse my windows network. What did I do wrong, and how can I achieve this. Thanks Jean [edit] - I want to browse the windows workgroup [edit] - Set the workgroup name, restarted the smb in the services, can browse network, but only my fedora 12 system is being shown

    Read the article

  • Is it possible to be a Linux professional studying on your own?

    - by Marc Jr
    I read economics at university(nothing to see with linux, isn't it? :P). I have some basic knowledge about booting process, Linux Kernel compiling from source and stuff like that. But of course I have still much to learn sometimes some errors appears and "voila" I am lost. I had: Ubuntu, Fedora, OpenSuse, Arch.. using Gentoo now. I'd like to know what you linux users, professionals, administrators... would think it is the best way to learn linux in a professional way. Is it worth studying it and passing the LPIC test enough to work in the linux world? or do I need going to IT uni? I've heard LFS is a good way of learning about linux, is that real? I've been thinking about getting to LFS learn about more deeply about the linux process and learning scripts. It is possible to do this way? if anyone has a tip or a good way of doing, maybe someone did it. Any tip is very welcome. Words from a person in love with linux. :D The best, Marc

    Read the article

  • How to configure wpa_supplicant on RHEL6?

    - by Yang Jy
    I am running a version of RHCE6 on my laptop. I uninstalled the default NetworkManager in order that I could configure the network all in the command line. The Ethernet part is okay, but I have problem bringing up the wireless interface. What I got is: Bringing up interface wlan0: Determining IP information for wlan0... failed; no link present. Check cable? I did exactly what this article says. I am not sure if it is because the article is obsolete or something else. Please help.

    Read the article

  • Linux on Sony Vaio VPCEB1S1E

    - by Jaakko
    I bought Sony Vaio VPCEB1S1E and I was able to surf on net. Then I tried to install Ubuntu 9.04 and Linux Mint on it but neither allows me an access to the Internet. How can I configure Mint so that I can go to net and get updates via apt-get? jaakko@jaakko-laptop ~ $ ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 46:83:d4:f4:36:bc BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 78:dd:08:c5:61:88 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster0 Link encap:UNSPEC HWaddr 78-DD-08-C5-61-88-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) jaakko@jaakko-laptop ~ $ ping 8.8.8.8 connect: Network is unreachable

    Read the article

  • Ubuntu 12.04 KVM running Ubuntu 12.04 with linux-image-virtual crash on boot

    - by D.Mill
    One of my VMs is stuck on "pause" in virsh. If I destroy and restart it, it will go to pause after a bit of time as "running". I can at best enter my username at login if I'm quick but it'll then shutdown. I don't know where to start with this so any help would be great!! I can access the VMs files via guestfish. the kern.log and syslog don't populate new lines. This is the last input I get from kern.log: Dec 13 11:21:08 soft201 kernel: imklog 5.8.6, log source = /proc/kmsg started. Dec 13 11:21:08 soft201 kernel: [ 0.000000] Initializing cgroup subsys cpuset Dec 13 11:21:08 soft201 kernel: [ 0.000000] Initializing cgroup subsys cpu Dec 13 11:21:08 soft201 kernel: [ 0.000000] Linux version 3.2.0-34-virtual (buildd@allspice) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #53-Ubuntu SMP Thu Nov 15 11:08:40 UTC 2012 (Ubuntu 3.2.0-34.53-virtual 3.2.33) Dec 13 11:21:08 soft201 kernel: [ 0.000000] Command line: root=UUID=61d48b48-a06a-48fb-842e-b38014086a93 ro quiet splash Dec 13 11:21:08 soft201 kernel: [ 0.000000] KERNEL supported cpus: Dec 13 11:21:08 soft201 kernel: [ 0.000000] Intel GenuineIntel Dec 13 11:21:08 soft201 kernel: [ 0.000000] AMD AuthenticAMD Dec 13 11:21:08 soft201 kernel: [ 0.000000] Centaur CentaurHauls Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-provided physical RAM map: Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dfffc000 (usable) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000dfffc000 - 00000000e0000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000feffc000 - 00000000ff000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000a20000000 (usable) Dec 13 11:21:08 soft201 kernel: [ 0.000000] NX (Execute Disable) protection: active Dec 13 11:21:08 soft201 kernel: [ 0.000000] DMI 2.4 present. Dec 13 11:21:08 soft201 kernel: [ 0.000000] DMI: Bochs Bochs, BIOS Bochs 01/01/2007 Dec 13 11:21:08 soft201 kernel: [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) Dec 13 11:21:08 soft201 kernel: [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) Dec 13 As you can see the last line gets cut off. I don't even know if this is that relevant. dmesg logs are empty. The qemu log for the VM returns this: 2012-12-13 12:29:47.584+0000: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-1.0 -enable-kvm -m 40960 -smp 14,sockets=14,cores=1,threads=1 -name numerink201 -uuid f4a889ed-a089-05d0-cc9d-9825ab1faeba -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/numerink201.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -drive file=/var/lib/libvirt/images/client.soft.fr/tmpcZAD9U.qcow2,if=none,id=drive-ide0-0-0,format=qcow2 -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0,bootindex=1 -fsdev local,security_model=none,id=fsdev-fs0,path=/home/shared_folders/soft201 -device virtio-9p-pci,id=fs0,fsdev=fsdev-fs0,mount_tag=hostshare,bus=pci.0,addr=0x5 -netdev tap,fd=18,id=hostnet0 -device virtio-net-pci,netdev=hostnet0,id=net0,mac=02:00:00:1d:b9:e7,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:0 -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/3 qemu: terminating on signal 15 from pid 28248 2012-12-13 12:30:14.455+0000: shutting down I've added more logging, libvirt.log gives me this: 2012-12-13 13:24:38.525+0000: 27694: info : libvirt version: 0.9.8 2012-12-13 13:24:38.525+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:38.525+0000: 27694: warning : qemuCapsInit:856 : Failed to get host power management capabilities 2012-12-13 13:24:39.865+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:39.865+0000: 27694: warning : lxcCapsInit:77 : Failed to get host power management capabilities 2012-12-13 13:24:39.866+0000: 27694: error : virExecWithHook:328 : Cannot find 'pm-is-supported' in path: No such file or directory 2012-12-13 13:24:39.866+0000: 27694: warning : umlCapsInit:87 : Failed to get host power management capabilities I don't really know where to go from here. I'll post whatever info you require

    Read the article

  • SVN and WebSVN with different users access restriction on multiple repositories on linux

    - by user55658
    and first of all sorry for my english. I've installed an ubuntu server 10.04.1 with apache2, subversion, svn_dav and websvn. (and others services of course, like php5, mysql 5.1, etc). I've configured my svn with multiple repositories, and each one with differents groups and users, like: /var/myrepos/repo1 group: mygroup1 /var/myrepos/repo2 group: mygroup2 /var/myrepos/repo3 user: johndoe With an easy access on svn_dav, works perfectly, ie: http://myserver/svnrepo1 accesibly only for users on mygroup1 with theirs users of linux and passwords of svn. Also works for the other repos with their users and groups. But when i tried with websvn, shows all repos without take care than if user on mygroup1 can view repo2 (that's i dont want do). You can login as any user on mygroup1, mygroup2, or johndoe, and you login into all repositories. I'll try to find a solution and I'll post the news, if anyone can helpme with this I'll preciated so much!!! Thanks for all I show my files: /etc/apache2/mods-available/dav_svn.conf <Location /svnrepo1> DAV svn SVNPath /var/myrepos/repo1 AuthType Basic AuthName "Repositorio Subversion de MD" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user </Location> <Location /websvn/> Options FollowSymLinks order allow,deny allow from all AuthType Basic AuthName "Subversion Repository" AuthUserFile /etc/apache2/dav_svn.passwd Require valid-user </Location>

    Read the article

  • Deploying a Git server in a AWS linux instance

    - by Leroux
    I'm making a git server on my linux instance in AWS. I tried doing it using these instructions but in the end I always get stuck with a "Permission denied (publickey)" message. So here is my detailed steps, the client is my windows machine running mysysgit and the server is the AWS ubuntu instance : 1) I created user Git with a simple password. 2) Created the ssh directory in ~/.ssh 3) On the client I created ssh keys using ssh-keygen -t rsa -b 1024, they got dropped in my /Users/[Name]/.ssh directory, id_rsa and id_rsa.pub key pair was created. 4) Using notepad I copy pasted the text into newly created files on the server in the ~/.ssh directory of my Git user. ~/.ssh/id_rsa and **~/.ssh/id_rsa.pub** were copied. 5) On the server I made the authorized_hosts file using "cat id_rsa.pub authorized_hosts" (while inside the .ssh directory) 6) Now to test it, on my client machine I did ssh -v git@[ip.address] 7) Result : debug1: Host 'ip.address' is known and matches the RSA host key. debug1: Found key in /c/Users/[Name]/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /c/Users/[Name]/.ssh/identity debug1: Trying private key: /c/Users/[Name]/.ssh/id_rsa debug1: Offering public key: /c/Users/[Name]/.ssh/id_dsa debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). I would appreciate any insight anyone can give me.

    Read the article

  • Slow wifi on Ubuntu 12.04 wifi driver ath9k

    - by lunar
    For the last couple of days my wifi connection is extremely slow. I am pretty sure that it is caused by the driver. Can this be improved? lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"MyWiFi" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:68:FE:7B:C7 Bit Rate=58.5 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:6960 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 74:f0:6d:34:c2:4e width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d7400000-d740ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:4b:38:78:f6:ae capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128) lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd Bus 001 Device 004: ID 0b05:1788 ASUSTek Computer, Inc. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 425M] (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB controller: Fresco Logic Device 1400 (rev 01) 06:00.0 Ethernet controller: Atheros Communications Inc. AR8131 Gigabit Ethernet (rev c0) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) rfkill list all 0: hci0: Bluetooth Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no

    Read the article

  • Arch linux - strange behaviour after installing fglrx

    - by kosto
    I have a problem with drivers on arch linux. I installed catalyst through unnoficial catalyst repo as wiki says. pacman -S catalyst catalyst-utils aticonfig --initial After this operation i rebooted the system. KDM loaded succesfully, but when i tried to switch to console (ctrl+alt+1/2/3) i saw only some strange dots, like pixels from the text were splitted on the whole screen. I was able to go back to kdm and enter the account details tho. This gave me a hang just before kde loaded. Here's a video where i'm showing above actions. Anybody knows what caused the problem? I can still chroot to fix some issues. Thanks for interest. http://glothriel.org/arch/arch_problem.ogg same thing on gnome / gdm, that's my second try on installing catalyst on arch. Open drivers suck the battery 2x faster. ___________EDIT_____________ Ok, i found a sollution, so i'm posting if someone else shares my problem. Catalyst does not support KMS, so you need to disable it from grub. You must know where are your /etc and /boot paritions mounted. If you have only one partition for / it's even simplier. Mount / on /mnt mount /dev/sdaX /mnt where X is number of the partition where is your / installed arch-chroot /mnt nano /etc/default/grub and add line: GRUB_CMDLINE_LINUX="nomodeset" save and quit then run (this will delete your windows grub configuration) grub-mkconfig -o /boot/grub/grub.cfg exit umount /mnt reboot

    Read the article

  • Video card not detected on Lenovo T410 in Linux

    - by wich
    I have a T410 with an nVidia NVS 3100M, this is not a hybrid system, there is no Optimus. (No option in the BIOS for Optimus, lspci in linux as well as the Windows device manager only show the nVidia) Using lspci I see the GPU as a present device, however, I can not, for the life of me, get any video driver to work that will let me start an X session, every time X craps out with the error (EE) No devices detected. I have tried the nVidia binary blob, (with nvidia-config, made sure no nvidia support in the kernel), I have tried nouveau, I have tried nv, I have even tried generic vesa, nothing will work. When I compare the dmesg that I get when loading the nvidia kernel module, I see that it is missing some lines compared with another system that also has an nvidia card, specifically the line mentioning the GPU name (3100M) is not there. I have checked every option in the BIOS, there is nothing to control except for the BIOS video output port, which is set to the LCD panel. I have no idea anymore what the problem may be, or even how I can diagnose this problem further. Any help will be appreciated.

    Read the article

  • Rsync Push files from linux to windoes. ssh issue - connection refused

    - by piyush c
    For some reason I want to run a script to move files from Linux machine to Windows. I have installed cwRsync on my windows machine and able to connect to linux machine. When i execute following command: rsync -e "ssh -l "piyush"" -Wgovz --timeout 120 --delay-updates --remove-sent-files /usr/local/src/piyush/sync/* "[email protected]:/cygdrive/d/temp" Where 10.0.0.60 is my widows machine and I am running above command on Linux - CentOS 5.5. After running command I get following error message: ssh: connect to host 10.0.0.60 port 22: Connection refused rsync: connection unexpectedly closed (0 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(463) [sender=2.6.8] [root@localhost sync]# ssh [email protected] ssh: connect to host 10.0.0.60 port 22: Connection refused I have modified my firewall settings on widows to allow all ports. I think this issue is due to SSH Daemon not present on my windows machine. So I tried installing OpenSSH on my machine and running ssh-agent but didn't helped. I tried similar command to run on my widows machine to pull files from Linux and its working fine. For some reason I want command for Linux machine so that I can embed it in a shell script. Can you suggest me if I am missing anything. I am already having cwRsync installed on my widows and running it in daemon mode using --damemon option. And I am able to login using ssh from windows machine to linux machine. When I issue bellow command, it just blocks for 120 seconds (timeout I specified in command) and exits saying there is timeout. rsync -e "ssh -l piyush" -Wgovz --timeout 120 --delay-updates --remove-sent-files /usr/local/src/piyush/sync/* "[email protected]:/cygdrive/d/temp" After starting rsync on widows, I checked, rsyc is running. And widows firewall setting are set to minimal, and on Linux machine stopped iptables service so that port 873 (default rsync port) is not blocked. What can be the possible reason that Linux machine is not able to connect to rsync-daemon on windows machine?

    Read the article

  • Weird permission issue with POSIX ACLs, NFS v3 on Linux

    - by jon
    I have two Linux systems, both running Debian Squeeze. Versions of (I think) the stuff involved are: kernel: 2.6.32-5-xen-amd64 ii nfs-kernel-server 1:1.2.2-4squeeze2 support for NFS kernel server ii libnfsidmap2 0.23-2 An nfs idmapping library ii nfs-common 1:1.2.2-4squeeze2 NFS support files common to client and server ii portmap 6.0.0-2 RPC port mapper (The client doesn't have nfs-kernel-server involved.) I have a directory with ACLs: # file: dirname # owner: jon # group: foogroup # flags: -s- user::rwx user:www-data:rwx group::r-x group:foogroup:rwx mask::rwx other::r-x default:... There are two users, neither one of which owns the directory: uid=3001(jake) gid=3001(jake) groups=3001(jake),104(wheel),3999(foogroup) uid=3005(nic) gid=3005(nic) groups=3005(nic),3999(foogroup) The jake user can create files in the directory without issues. The nic user can't. All UIDs/GIDs are the same on the client and server. I've verified (packet sniffing) that the right uids/gids get sent via AUTH_UNIX are correct-- uid=gid=3005, auxiliary gids=3005,3999-- and that the server replies with NFS3ERR_ACCESS, which the kernel on the client maps to EACCES (Permission denied). Can anyone help me here?

    Read the article

  • Limiting bandwidth on internal interface on Linux gateway

    - by Jack Scott
    I am responsible for a Linux-based (it runs Debian) branch office router that takes a single high-speed Internet connection (eth2) and turns it into about 20 internal networks, each with a seperate subnet (192.168.1.0/24 to 192.168.20.0/24) and a seperate VLAN (eth0.101 to eth0.120). I am trying to restrict bandwidth on one of the internal subnets that is consistently chewing up more bandwidth than it should. What is the best way to do this? My first try at this was with wondershaper, which I heard about on SuperUser here. Unfortunately, this is useful for exactly the opposite situation that I have... it's useful on the client side, not on the Internet side. My second attempt was using the script found at http://www.topwebhosts.org/tools/traffic-control.php, which I modified so the active part is: tc qdisc add dev eth0.113 root handle 13: htb default 100 tc class add dev eth0.113 parent 13: classid 13:1 htb rate 3mbps tc class add dev eth0.113 parent 13: classid 13:2 htb rate 3mbps tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip dst 192.168.13.0/24 flowid 13:1 tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip src 192.168.13.0/24 flowid 13:2 What I want this to do is restrict the bandwidth on VLAN 113 (subnet 192.168.13.0/24) to 3mbit up and 3mbit down. Unfortunately, it seems to have no effect at all! I'm very inexperienced with the tc command, so any help getting this working would be appreciated.

    Read the article

  • Gentoo Linux useful utilities

    - by Alakdae
    I want to make a list of utilities that come in handy in Gentoo (general Linux tools available in all distributions also appreciated). What tools and commands do you use and consider helpful in administration of a Gentoo server? I will update the list with command from answers from time to time. eclean Utility for cleaning distfiles and binary packages. Usage example: eclean distfiles Usage example output: Cleans out the files in /usr/portage/distfiles. Pretty handy. Package: app-portage/gentoolkit eix Very useful tool for getting information about a package. Similar to "emerge -s" but much faster and more precise. Usage example: eix gentoolkit Usage example output: Show information about package such as: available versions, masked versions, installed versions and description. Package: app-portage/eix eix-test-obsolete Check system for obsolete, redundant, uninstalled entries in package.keywords, package.mask, package.unmask, package.use and package.cflags Usage example: eix-test-obsolete Usage example output: Shows non-matching entries, redundant entries, and uninstalled entries. Package: app-portage/eix equery Another very useful tool for getting information about packages (listing package files, checking which files belong to which package and much more) Usage example: equery b emerge Usage example output: Show which packages installed a file called emerge Package: app-portage/gentoolkit genlop Utility for extracting information about emerged ebuilds Usage example: genlop -l --date yesterday Usage example output: Show a list of packages that have been emerged yesterdayPackage: app-portage/genlop glsa-check Checks system if it's affected by GLSAs (security issues) Usage example: glsa-check -l affected Usage example output: List of GLSA that the system is affected by. Package: app-portage/gentoolkit rc-update Utility for managing (adding, deleting) runlevel scripts. Usage example: rc-update add syslog-ng default Usage example output: Adds syslog-ng to default runlevel. Package: sys-apps/baselayout revdep-rebuild Scans libraries and binaries for missing shared library dependencies Usage example: revdep-rebuild Usage example output: Gather binaries and libraries information, check for dependencies, rebuild packages with missing dependencies Package: app-portage/gentoolkit

    Read the article

  • How can I change the amount of video memory with a Mobile Intel 4 Series Express Chipset?

    - by user45924
    I have the chipset in the title. The Intel control panel says the following: Intel® Graphics Media Accelerator Driver for Mobile Report Report Date: 8/11/2010 Report Time[hr:mm:ss]: 20:2:54 Driver Version: 8.15.10.2182 Operating System: Windows 7 (6.1.7600) Default Language: English (Canada) DirectX* Version: 10.0 Physical Memory: 3963 MB Minimum Graphics Memory: 128 MB Maximum Graphics Memory: 1759 MB Graphics Memory in Use: 17 MB Processor: Intel64 Family 6 Model 23 Stepping 10 Processor Speed: 1995 MHz Vendor ID: 8086 Device ID: 2A42 Device Revision: 07 Even while playing games, the Graphics Memory in Use only ever goes up to 26 MB. I've looked in the BIOS; there's nothing there. Is there any way I can force it to go higher? Thanks :)

    Read the article

  • Limiting interface bandwidth with tc under Linux

    - by Matt
    I have a linux router which has a 10GBe interface on the outside and bonded Gigabit ethernet interfaces on the inside. We have currently budget for 2GBit/s. If we exceed that rate by more than 5% average for a month then we'll be charged for the whole 10Gbit/s capacity. Quite a step up in dollar terms. So, I want to limit this to 2GBit/s on 10GBe interface. TBF filter might be ideal, but this comment is of concern. On all platforms except for Alpha, it is able to shape up to 1mbit/s of normal traffic with ideal minimal burstiness, sending out data exactly at the configured rates. Should I be using TBF or some other filter to apply this rate to the interface and how would I do it. I don't understand the example given here: Traffic Control HOWTO In particular "Example 9. Creating a 256kbit/s TBF" tc qdisc add dev eth0 handle 1:0 root dsmark indices 1 default_index 0 tc qdisc add dev eth0 handle 2:0 parent 1:0 tbf burst 20480 limit 20480 mtu 1514 rate 32000bps How is the 256K bit/s rate calculated? In this example, 32000bps = 32k bytes per second. Since tc uses bps = bytes per second. I guess burst and limit come into play but how would you go about choosing sensible numbers to reach the desired rate? This is not a mistake. I tested this and it gave a rate close to 256K but not exactly that.

    Read the article

  • Hyperic HQ- Monitor process statistics for 50+ processes on Linux machine

    - by Chris
    Is there an easy way to get metrics on all processes that start with the letters XYZ? I have about 80 processes that I have to monitor individually that all start with the prefix XYZ. I have created a query using the sigar shell: ps State.Name.sw=XYZ, which will give me a list of the processes that I want. What I need to do is define this list of processes through said query and collect and track statistics from the Process service: http://support.hyperic.com/display/hypcomm/Process+service What I need is 3 or 4 key statistics for each of the XYZ processes defined by my query to show up as graphs in the web front end. Note: Hyperic HQ server is installed on a windows machine and I'm monitoring a Linux box via an agent. Thanks, Chris Edit: Here is my try at a plugin that may give me what I want, but it's not being inventoried/detected by the Hyperic web UI. Simply pointing me to one of Hyperic's tutorials won't do. Thanks. <!DOCTYPE plugin [ <!ENTITY process-metrics SYSTEM "/pdk/plugins/process-metrics.xml">]> <plugin> <server name="ABCStats"> <config> <option name="process.query" description="Process Query" default="State.Name.sw=XYZ"/> </config> <metric name="Availability" alias="Availability" template="sigar:Type=ProcState,Arg=%process.query%:State" category="AVAILABILITY" indicator="true" units="percentage" collectionType="dynamic"/> &process-metrics; <plugin type="autoinventory"/> <plugin type="measurement" class="org.hyperic.hq.product.MeasurementPlugin"/> </server> </plugin>

    Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >