Search Results

Search found 20116 results on 805 pages for 'network flow'.

Page 75/805 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• Routing traffic to another internal network

  - by Jason

  OK, so here is the scenario. I have 4 Locations connected with an MPLS. I have installed an ASA at the primary location which is 10.20.1.0. Traffic is fine internally and to the world, however... I can't route traffic over the MPLS to another network. It is being blocked by an implicit deny rule even though there is a rule to allow any to any less secure interface (it should be using the same interface in/out, right?). I have a static route for the network in and the ASA can ping it - Just not traffic on the internal network of the ASA. -Jason

  Read the article

• Mac Parallels - Bridged network

  - by Jack

  Hey All, I am new to Apple and my task is to install VMs on a Mac server. I am trying to install 4 VMs and I want them to have separate IPs and be visible on the network as separate machines. What are my options ? My research shows me that I can use bridged network, but I have to select an adapter. I have only two network adapters, does that mean I can only have 2 VMs ? And when I configure the 2 VMS, will my actual server have internet connection ? Or does it use the Mac address ?

  Read the article

• Local network cache of PHP and Apache2 on Win Server 2008 R2

  - by Ahmed Benlahsen

  Software configuration : I have a new server with Windows Server 2008 R2 installed via VMWare. I have installed Apache2.2, PHP5.2 and MySQL5.5 as separate packages. Issue : On my first installation of my application, all works great. When I updated some JS and CSS files and accessed my application again from a PC on local network, I got the old JS and CSS versions. When I access the same application on local server I got the latest versions of those files. Link of my application on local server is : http://localhost/BADIL Link of my application from local network is : http://LOCAL_SERVER_IP/BADIL I think that must be some cache but I don't know where. Maybe on Win Server 2008 R2 or on VMWare? The question is: Why, when I access my application on the server, everything works fine, but when I access the same application from a local network, I do not see the updated versions of JS and CSS files?

  Read the article

• Routing traffic to another internal network

  - by Jason

  OK, so here is the scenario. I have 4 Locations connected with an MPLS. I have installed an ASA at the primary location which is 10.20.1.0. Traffic is fine internally and to the world, however... I can't route traffic over the MPLS to another network. It is being blocked by an implicit deny rule even though there is a rule to allow any to any less secure interface (it should be using the same interface in/out, right?). I have a static route for the network in and the ASA can ping it - Just not traffic on the internal network of the ASA. -Jason

  Read the article

• Running .net application over a network

  - by Marlon

  Hello, I need some advice please. I need to enable a .Net application to run over a network share, the problem is that this will be on clients network shares and so the path will not be identical. I've had a quick look at ClickOnce and the publish options in VS2008 but it wants a specific network share location - and I'm assuming this location gets stored somewhere when it does its thing. At the moment the job is being done with a old VB6 application and so gets around all these security issues, but that application is poorly written and almost impossible to maintain so it really needs to go. Is it possible for the domain controller to be set up to allow this specific .Net application to execute? Any other options would be welcomed as I want to get this little application is very business critical. I aught to say that the client networks are schools, and thus are often quite locked down as are the client machines, so manually adding exceptions to each client machine is a big no no. Marlon

  Read the article

• Vista: "connect to a network" does not load (can't set up VPN)

  - by Arkaaito

  I'm trying to connect to my office VPN from home. One small problem: my home desktop uses Vista (64-bit, Ultimate edition). On Vista, you're supposed to set up a VPN like so: Open the control panel Click on Network Click on "Connect to a Network" Configure a new connection of type "Office" The problem is, when I click on the link for "Connect to a Network", nothing happens. Can anyone suggest how I should go about troubleshooting this? (Or am I better off just upgrading to Windows 7?)

  Read the article

• Copy Network Volume configuration among Linux systems

  - by David Yu

  I have several standalone Debian Linux (Lenny) systems. As it stands now, all of the systems are configured with a generic login account. This login account has a network volume that connects to a Windows share on a Windows server. I need to create a batch of user accounts on all of the systems (this part I figured out). After I create all of the user accounts, I need all of them to have the same network volume mapping as the current generic account. Is the network volume configuration saved somewhere, where I could copy that configuration across all of the user accounts?

  Read the article

• "Failed to delete the item from the trash" on network drive files

  - by bstpierre

  How does the Ubuntu trash work? It appears that one trash bin is used by many drives. I've noticed a folder called ".Trash-1000" on my network drive as well as "/home/user/.local/share/Trash". Currently I have a problem where a number of files I deleted from a network drive (which I no longer have full access to) appear in my trash but but cannot be deleted, I see the error "Failed to delete the item from the trash". If I look at the files in this network drive trash I notice that it contains all of these undeletable files. I am running Ubuntu 9.10 x64.

  Read the article

• How to automount SMB shared network drives in Mac OS X Lion

  - by cyppher

  In Mac OS X 10.7 (Lion) Apple has replaced good old SMB support. Now I can't auto connect to my shared (SMB) network drives. Workarounds? Or Impossible? In OS X Snow Leopard, I could automatically connect my Ubuntu (SMB) shared network drives with auto_smb / auto_master (autofs configuration in /private/etc/). I made three mount points (folders) directly in '/Volumes', I used /Volumes/Data and /Volumes/webroot (both SMB shared). Unfortunately Lion doesn't connect (automount) my network drives. I have to manually connect to the server (Ubuntu file server) in Finder, then open up Terminal to navigate to the mount points, and then it connects. This is not a workable solution. I've searched (Google/SO) but found no solutions apart from an unsupported hack. Isn't it possible any more to automatically connect to an SMB-shared drive during startup?

  Read the article

• Oracle 11g network configuration

  - by Kylo

  I installed Oracle 11g Enterprise Edition on my Windows 7 Pro. My problem is that I cannot log into database from other host (local network). When I connect to database using Oracle SQLdeveloper everything is ok as long as I specify 'localhost' in connection configuration. However, when I change it to '192.168.0.190' which is my host IP address I get 'The Network Adapter could not establish the connection'. I get the same error when logging in from other host in local network. What is the problem?

  Read the article

• Connection drops while transferring large files to one server on a network

  - by Charlotte

  My company has two sites, each with their own LAN, using site to site VPN tunnel to connect the two sites. When transferring files (especially larger files) from site1 to site2 server1, the file transfer fails. I don't think this can be a VPN issue because transferring the same files to site2 server2 which is on the same network as server1 works fine. Pings to server1 and server2 at site2 from site1 are about the same, mostly 19/20ms with the odd one up to 50ms. As server1 is DB server with a high load I thought the NIC maybe overloaded, but a transfer from site2 server1 to site2 server2 works fine, and that uses the same NIC on server1 as transfers from site1 to site2 server1. The servers are both Windows Server 2003 VMs with VMXNET 3 NICs. Site2 Server1 route print: IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 28 9b ...... vmxnet3 Ethernet Adapter #2 0x10004 ...00 50 56 99 18 97 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.18 10 10.10.10.0 255.255.255.0 10.10.10.70 10.10.10.70 10 10.10.10.70 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.18 172.20.10.18 10 172.20.10.18 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.18 172.20.10.18 10 224.0.0.0 240.0.0.0 10.10.10.70 10.10.10.70 10 224.0.0.0 240.0.0.0 172.20.10.18 172.20.10.18 10 255.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 1 255.255.255.255 255.255.255.255 172.20.10.18 172.20.10.18 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site2 Server2 route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 15 00 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.114 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.114 172.20.10.114 10 172.20.10.114 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.114 172.20.10.114 10 224.0.0.0 240.0.0.0 172.20.10.114 172.20.10.114 10 255.255.255.255 255.255.255.255 172.20.10.114 172.20.10.114 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site1 Server route print: =========================================================================== Interface List 14...00 50 56 93 00 0b ......vmxnet3 Ethernet Adapter #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.168.1 192.168.168.118 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.168.0 255.255.255.0 On-link 192.168.168.118 261 192.168.168.118 255.255.255.255 On-link 192.168.168.118 261 192.168.168.255 255.255.255.255 On-link 192.168.168.118 261 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.168.118 261 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.168.118 261 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.168.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 261 fe80::/64 On-link 14 261 fe80::3c6b:996f:ef36:ee76/128 On-link 1 306 ff00::/8 On-link 14 261 ff00::/8 On-link =========================================================================== Persistent Routes: None tracert from site1 to site2 server1: Tracing route to server1 [172.20.10.18] over a maximum of 30 hops: 1 19 ms 19 ms 19 ms server1 [172.20.10.18] Trace complete. tracert from site2 server1 to site1: When this was run it went to the external IP of site2, then to a couple of external ips of the isp, then times out. Can anyone suggest any troubleshooting steps? Thanks, Charlotte.

  Read the article

• Macbook cannot see specific wireless network after being connected to it for a while

  - by donut

  Okay, so there's a single wireless network that my laptop has troubles with. My Macbook Pro used to be fine with it until it changed to using channel 13 (or 11?). Since then, after being connected to it for a while it disappears from my laptop's view. Other networks are showing up fine and other computers (including several Macs) have no troubles connecting to this network. If I clear my system cache using Onyx and then restart (sometimes a couple times) my laptop can see and connect to it again. But it seems that if I disconnect and try reconnecting I have to clear my cache again. One thing to note is that if I put my computer to sleep while connected to this network it has no problems reconnecting on wake up. I've got a 15" Macbook Pro 2,2 with Leopard 10.5.8.

  Read the article

• Analyze a wireless network that constantly drops/has speed issues

  - by Eddie Parker

  Hello, I'm curious what the best tools are to use for analyzing problems with a WiFi network. Here's the scenario: I have a WiFi router (Belkin N+) that's setup in AP mode. I have three RT-N13U's that I've purchased to use as 'repeaters', but I've had so many problems when more than one of them is running (bad routes) that I've only got one active. Sometimes certain boxes on my network can't talk to others, and drops are quite frequent and quite aggravating. I'm running Mac, Windows, and Linux (Gentoo) boxes on this network, so any software, or steps I should take that work for any of those boxes should be sufficient. Apologies if this is answered somewhere else - I'll close it as a dupe if so.

  Read the article

• How can I view my IIS hosted sites on other machines on my network

  - by Truegilly

  Hello, at home i have a simple network setup conatining 2 machines and 1 belkin router. On one machine i have a site hosted with IIS7. Rather than the standard localhost/index.htm address i have added an entry in the HOSTS file pointing the local ip (127.0.0.1) to this domain - www.mysite.dev. i can access the site with www.mysite.dev with no problem. what i would like to do is be able to view this site from my other machine on the network. initially i assumed this could be done with a url like so MACHINE-NAME/www.mysite.dev, but the connection always times out. But I can ping MACHINE-NAME without problems. For testing purposes i have diabled the windows firewall on both machines but to no joy. Like a typical web developer, my techy/network skills are pretty poor. Can anyone see where im going wrong ?? thank you for your time Truegilly :)

  Read the article

• Mac claims to have connected to wireless network, but hasn't

  - by Mick

  I am attempting to connect a new mac OSX 10.6.5 laptop to a wireless network (I am a windows expert but a mac novice). It used to connect without problem to the network when I had the security set to "64 bit wep". Now I have changed the security on my belkin router to "WPA-PSK (no server)". I have two PC's and an old mac connecting via the new security setting without problem. Now I have the problem that on the new mac, the wireless icon is indicating a good connection (5 dark bars). Also the network name has a tick next to it on the wireless drop down menu. But I can not view any websites. I can not even connect to the router by typing 192.168.2.1 into a browser address bar. Any ideas where I went wrong?

  Read the article

• How to execute everything in the Local Area Network

  - by matnagel

  We have a very small LAN here, but some peolpe here think we need Active Directory, though nobody knows how to maintain it. I am not in the position to change this. How can I get full access (on Linux it would be "execute" rights) also for files on network drives (the files are just on another machine next room) My account is in the group Administrators on a windows 2003 server Domain Controller. I cannot open simple MS Access 2000 Databases or CHM Files from network drives in the lan How to do that? Some policy setting? I want to change that once. It is useless. We have no distinction between local or network files here. I would have to copy everything to a local drive and then do what I want.

  Read the article

• Mac Parallels - Bridged network

  - by Jack

  I am new to Apple and my task is to install VMs on a Mac server. I am trying to install 4 VMs and I want them to have separate IPs and be visible on the network as separate machines. What are my options? My research shows me that I can use a bridged network, but I have to select an adapter. I have only two network adapters, does that mean I can only have 2 VMs? And when I configure the 2 VMS, will my actual server have internet connection? Or does it use the Mac's address?

  Read the article

• Mixed network, Linux-to-Linux hostname resolution issues

  - by James

  At work we have an WinSBS domain at the heart of our network, which is all Windows PCs. The domain controller is acting as a DNS for these computers. I have recently added some personal use Linux machines to the network, without joining them to the domain. I have set up Samba with "wins server" pointing to the domain controller, which lets the Windows boxes resolve the Linux hostnames just fine. I also have resolvconf set up with the domain controller as a nameserver and the local domain as a searched domain, which lets the Linux boxes resolve the Windows hostnames just fine. However, the Linux boxes will not resolve other Linux hostnames at all. Given that I don't have control over the DNS server (I am not the network admin) and that at least one of the Linux boxes is not an always-on machine and is likely to change its LAN IP frequently (via DHCP), what service am I missing to make their hostnames visible to each other?

  Read the article

• OS X will not register newly installed network adapters

  - by Chris

  I have purchased an Edimax 7318USg and tested it on a Windows machine (works). The installation process for the software for this adapter runs smoothly. However, OS X simply does not recognize new network adapters. When you go to System Preferences/Network, a new network adapter should be present/there should be an alert. This is not the case. Why might this be? Is there a setting I may reset to force the operating system to recognize this? Thanks!

  Read the article

• Ubuntu Kernel Panic on Inserting Network Cable

  - by Skizz

  I've been having a recurring kernel panic with my Ubuntu 9.04 installation (see other posts by me). Today, I was fiddling around trying to get some cable attached when the system panicked. Looking at the layout, the only cable in the vicinity was the network cable. Upon further investigation, it seems that the system reliably panics whenever I insert a network cable. Removing the cable does not cause the panic. How do I stop the system panicking when I insert the network cable? If more information is needed, please add comments/answers and I'll post the required data.

  Read the article

• Planning home network

  - by gakhov

  I'm planning to setup my home network from scratch and want to ask professional opinions or tips. My home is connected to Internet with a cable connection (100 Mb/s). The devices I would like to connect are VoIP phone (RJ-45), TV (WiFi/LAN), 3 laptops (WiFi), 2 smartphones (WiFi), an iPad (WiFi), a Kindle (WiFi), a network printer and, probably, a home media storage (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, I need help to choose the best router (or combination of routers) to support stable connections for all these devices and minimize the total number of routers/adapters. I like how Cisco/Linksys devices were working for me in the past, so preferably (but not obligatorily) I want to setup network with their solutions. Any thoughts?

  Read the article

• Windows 7 freezes on connecting second time to same wifi network

  - by Rakesh Juyal

  I am using Lenovo - y470, which comes with windows 7 home premium. I can connect to my wifi network and there is no issue in that. But the problem comes if the network get disconnected and i again try to connect to same wifi network. As soon as i click on connect my system freezes, and i can not even press ctrl+ alt+ del . The only think i am allowed to do at that time is press and hold power button to shut down the system and restart it again. Please tell me how to resolve this issue. Please let me know if some more information is required. OS: Windows 7 Router: Netgear n-150

  Read the article

• Problems connecting Centos to the network when running in VMWare

  - by Sakin

  Hi, I installed CentOs on VMware running on windows XP. When trying to configure it to connect to the internet, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. I tried to configure VMWare to use a bridged connection as well as NAT connection. An image of Ubuntu runs fine on the same VMware. What am I missing here? Thanks.

  Read the article

• gigabit network with adsl modem

  - by user51006

  Hi, i would like to build a gigabit network to connect the different computers at my home. I already have an 100Mb adsl router/modem but i have an hard time to find a 1000Mb one, so i came up with the idea of using a normal 1000Mb router or switch to put between the adsl modem and the computers. So i only use the adsl modem to connect to the internet and the gigabit router as dhcp to connect the different computers. But to get to the question. Will the 100Mb adsl router slow down my network? Will data travel like pc gigabit router computer or pc gigabit router adsl router gigabit router pc. My gut says it will go like in the first option but i have seen network hardware do some weird stuff. What do you think?

  Read the article

• Why does WebDAV fail from inside home network

  - by Claus

  On my OSX server there is a folder that is configured in the Server App to be accessible via WebDAV. This folder is used to sync OmniFocus. On my router, I have set up a dynamic dns. When I am outside my home network (physically away or when connected via a vpn), I can connect and sync fine via: https://<server name from dyndns>/<username>/<path to WebDAV folder> However, when I am in my home network, the connection to WebDAV does not work (other connections, AFP, f.ex, do work). What could be some reasons why I can't connect to WebDAV from within my home network? What log files could give hints and where are they stored? I am running OSX server 10.9.3. and server.app. Thanks for your help.

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >