Search Results

Search found 22600 results on 904 pages for 'remote connection'.

Page 75/904 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

  • What ports should I open for listen and/or transmit in my firewall to keep internet ok?

    - by H_7
    What are the minimum ports and services that should I allow/open for listen and/or transmit in my firewall (I am using Firestarter) to keep my internet running ok? Some talk about what services, which port uses, and why it matters should be nice too. Thanks for any advice. I have some bet to the answer 80 http 443 https 53 dns EDIT: I will just browse some sites. I have a windows virtual machine, so I ll use it too, bu t just normal navigation too. No torrents, IRC's, FLASH, etc.. Thanks for attention. hmmm... lost! Linux Mint 9 here.

    Read the article

  • Issue with setting up multiple IP addresses on ubuntu server installation

    - by varunyellina
    I want to setup two ip addresses on my system for access through lan. This is my config on my other system. Desktop Installation My desktop installation runs with multiple IP's added through networkmanager both through lan and wifi. Server Installation On my server install I've edited /etc/network/interfaces to the following. auto eth0 auto eth0:1 # IP-1 iface eth0 inet static address 172.16.35.35 network 172.16.34.1 netmask 255.255.254.0 broadcast 172.166.35.255 dns-nameservers 172.16.100.221 8.8.8.8 # IP-2 iface eth0:1 inet static address 172.16.34.34 network 172.16.34.1 netmask 255.255.254.0 gateway 172.16.34.1 broadcast 172.16.35.255 After restarting through "/etc/init.d/networking restart" I recieve "Failed to bring up eth0:1" What am I doing wrong? Thankyou.

    Read the article

  • How to print over ssh?

    - by mit
    I have the following configuration: P == U ---------------- W P is a HP Laserjet, connected to U, which is an Ubuntu 10.04 desktop machine with a standard gnome setup from the live cd. I just selected the HP Laserjet in the gnome printer admin and it works, I can print locally. W is a remote windows machine, server 2003, and --- is an untrusted connection. I wonder if I can create an ssh tunnel between U and W, so W can print using U's printer service. Which ports will I need to forward and what kind of printer must I add then on the windows machine?

    Read the article

  • Desktop sharing options for Ubuntu 12.04 with Unity

    - by Stefan Buynov
    I would like to be able to access my office Ubuntu 12.04 machine from home, from a Mac Mini with Mac OSX. I have a VPN and I am able to access my office machine over SSH, so connectivity is not a problem. I browsed other questions, and it seems that there are several options: VNC XRDP FreeNX (haven't heard this one before) Are there any other? I have been using Remote Desktop on Windows before, and I actually like it. Not sure how well is XRDP implemented. I also used VNC several years back, and I didn't like its performance back then - not sure if things have changed since then. As I said above, the machine I want to access is running Ubuntu 12.04, with Unity. And I am using Unity by choice - I really like it and would like to continue using it :) The client computer is running Mac OSX (Snow Leopard). Based on your previous experience what is the best setup for this environment?

    Read the article

  • "The system is running in low graphics mode", unable to connect to the Internet

    - by Blah
    When I try to log onto Ubuntu, I get a notice that reads: The system is running in low graphics mode. I searched for a solution and there are a slew of answers. However, many of them seem to suggest reinstalling different things. After pressing Ctrl+Alt+F1 and getting to a terminal, I attempt commands like sudo apt-get install example. Upon doing so I get notices that say things such as could not resolve host which I am assuming means I'm not connected to the Internet. Since I can not connect to the Internet, none of these responses are helpful to me. What can I do?

    Read the article

  • Ubuntu Live USB: best practices for secure net traffic

    - by Och
    I want to to set up a live USB with Ubuntu, in the most secure way. So I want to have the persistent data on a second USB, something that its not that much problematic. How to configure a very safe Internet surfing (throughout a VPN?) Which are the best practices that could be implemented to have the Ubuntu live in a USB, the persistent data in other, and with the Internet access to a VPN (the Ubuntu privacy remix gives most of this, except the VPN config), Any ideas of how to combine the best of Ubuntu privacy remix, and Internet access to a VPN?

    Read the article

  • ubuntu 12.04 internet stopped working

    - by Daniel
    My laptop was running smoothly until yesterday. Today, I can't connect to the internet at home anymore. I am only able to access the router, but no internet access. A have a Dell Latitude E6320 with ubuntu 12.04. At my job, I don't have any problems connecting this laptop both via wireless and ethernet. At home, if I try connecting it through Windows it does work fine. I even checked the MAC addess and it's OK. My other laptop, which also runs ubuntu, is not facing this problem. I have already tried to restart and downgrade network-manager package and its dependecies. Anyone can help me please??? I am affraid I will have to reinstall everything...

    Read the article

  • Internet stopped working suddenly on 12.04

    - by Daniel
    My laptop was running smoothly until yesterday. Today, I can't connect to the Internet at home anymore. I am only able to access the router, but no Internet access. A have a Dell Latitude E6320 with Ubuntu 12.04. At my job, I don't have any problems connecting this laptop both via Wireless and Ethernet. At home, if I try connecting it through Windows, it does work fine. I even checked the MAC address and it's OK. My other laptop, which also runs Ubuntu, is not facing this problem. I have already tried to restart and downgrade network-manager package and its dependencies. Can anyone help me please? I am afraid, I will have to reinstall everything.

    Read the article

  • 12.04 - why does the network icon dissapear every time my machine is turned off

    - by Howard Walker
    After spending an hour or two working out how to find the network Icon, I find that when I reboot the machine, I have to go through the whole procedure again. 1. The network menu is not there - so first I have to find the terminal. This has no particular location that I can find but usually I have to type terminal in the dash. 2. Then I have to type nm-applet in terminal 3. The network manager icon then appears, but only works if the terminal window remains open. Shut down the terminal window and the network disappears. This is a pain - plus I have to type my password in every time, which is another waste of time, thought this has always been a problem. So can anyone tell me how to make the web automatically connect at startup without any intervention from me.

    Read the article

  • HP 530 Wireless problem. Bad communication with access point

    - by foxy
    I installed Ubuntu 11.10 on HP 530 and to make Wireless work installed STA driver from jockey (obviously proprietary) and, since it didn't work also installed their driver from HP website via ndiswrapper. After this (and a reboot) I see the WiFi indicator glowing, like it should be, and I am able to find local access points. But when I try to connect to mine personal one with WPA 2 security (with password) it hangs at authentification (I'm using wicd to manage wifi), and after a minute or so (I guess timeout of request happens) it says I have a wrong password (it is 100% correct). What might be the problem here? Yesterday I was able to connect to access point by changing type of encryption from passphrase to preshared key but didn't have internet access. Now, after reboot, I can't connect there again.

    Read the article

  • How do I get an Xstream mobile phone working as a modem?

    - by callmegus
    I bought a CDMA mobile phone that can use as modem, this http://smartfren.com/xstream/ and i wanna try it on my ubuntu plug usb , and run "lsusb" callmegus@Presario-CQ43-304AU:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 058f:a001 Alcor Micro Corp. Bus 003 Device 002: ID 1bbb:0106 T & A Mobile Phones Bus 003 Device 003: ID 15d9:0a4c Trust International B.V. USB+PS/2 Optical Mouse Bus 004 Device 002: ID 0a5c:21e3 Broadcom Corp. I successfully "modprobe" this device, and connect to internet, but it's disconnected somehow .. and i can recconect it. I try "lsusb" again .. and something went wrong, here Bus 003 Device 002: ID 1bbb:1000 T & A Mobile Phones I do "modprobe" again and again , but it still won't connect Please guide me

    Read the article

  • Cannot connect to Internet on 11.04 using BSNL EVDO Prithvi Card

    - by Joy
    I cannot connect to Internet using BSNL EVDO Prithvi data card. Went through some websites that offered help, installed wvdial package and tried again, but was unsuccessful. I have Read that, Ubuntu 11.04 automatically detects Data Card, You only need to configure "Network Manager" and it will work, I did exactly that, but the result is same. The OS detects the data card, and the presence of network , but it cannot login. I have read in some forums that Ubuntu 11.04 does not have support for BSNL EVDO Prithvi, is it true? I re-checked the "User ID" and "Password". Its working on Windows. Please help me fix this.

    Read the article

  • Does the Ubuntu One sync work?

    - by bisi
    I have been on this for several hours now, trying to get a simple second folder to sync with my (paid) account. I cannot tell you how many times I removed all devices, removed stored passwords, killed all processes of u1, logged out and back in online...and still, the tick in the file browser (Synchronize this folder) is loading and loading and loading. Also, I have logged out, rebooted countless times. And this is after me somehow managing to get the u1 preferences to finally "connect" again. I have also checked the status of your services, and none are close to what I am experiencing. And I have checked the suggested related questions above! So please, just confirm whether it is a problem on my side, or a problem on your side. EDIT: In the mean time, here is what has changed, on top of what is mentioned just above. • My files went from 0MB to 71.9MB, and is still rising. • My first folder of 400.2MB is being filled with the data as I write this. The second folder has the folder sub-structure in place. • Both folders now show in the File Browser that it will be synchronized. I believe that right now, it is all back to normal and working fine, and I guess that's what a good night's sleep can do ;). And we're now only back to the point where synchronizing is slow, but will pick up with the release of Natty (https://wiki.ubuntu.com/UbuntuOne/FAQ/WhyIsItTakingSoLongForMyFilesToSync). But to get to the questions: My about says I use 11.04, Natty Narwhal, but I am quite sure the last distribution I installed was 10.10. Folder A is 400.2MB, and Folder B is 29.5MB I am on a DSL line, behind a regular fritz.box setting. No proxy servers in use, and I did not install any particular firewall features. No physical firewall, just the router (on which I have a TV signal as well), and 2 switches to get to this floor. Status: inactive The ubuntuone-indicator runs the same window as when I click on my name on the top-right corner and select Ubuntu one, or in the Control Center choose Ubuntu one. It wasn't supposed to go further than this was it?

    Read the article

  • Unable to connect to internet

    - by Peter Schriver
    I just upgraded to 12.10. Everything appears to go well but I am unable to connect to the Internet. The LAN is fine and I can view my shared files but no e-mail or access to web pages. My other computer which is running 12.04 or older seems to connect fine. I only upgraded one to make sure things would be ok. I am currently connecting fine with a wireless Windows laptop. Output from cat /etc/resolv.conf # Generated by NetworkManager nameserver 127.0.0.1

    Read the article

  • Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

    - by user42424
    So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

    Read the article

  • Is it me, or is it you? Does the sync work?

    - by bisi
    I have been on this for several hours now, trying to get a simple second folder to sync with my (paid) account. I cannot tell you how many times I removed all devices, removed stored passwords, killed all processes of u1, logged out and back in online...and still, the tick in the file browser (Synchronize this folder) is loading and loading and loading. Also, I have logged out, rebooted countless times. And this is after me somehow managing to get the u1 preferences to finally "connect" again. I have also checked the status of your services, and none are close to what I am experiencing. And I have checked the suggested related questions above! So please, just confirm whether it is a problem on my side, or a problem on your side.

    Read the article

  • Ubuntu 12.10 not properply working on Asus u46E after Update

    - by John Oakland
    I recently installed the latest Ubuntu update on my laptop and since then, the alignment on the browser is messed up, the mouse is not working, and I can't connect to the internet. Before it was working perfectly. Any ideas on what to do? Thanks for any feedback FYI: I am right now using windows since I have both linux and windows on my laptop. Also, when booting I do have the option to boot previous ubuntu versions, when I boot the previous unbuntu version on my laptop, everything works accept except the internet. (the mouse works, alignment is proper)

    Read the article

  • WiFi can't connect after suspend

    - by CyberOPS
    I've had this problem since Ubuntu 11.10 (my first install) but I was able to get around this issue with this answer. After I installed Ubuntu 12.04.1 I tried to use the same fix as before but I couldn't get it to work. I've also tried a couple other different fixes I found around the web but they didn't work. Basically here's what happens: I can see all the networks in my area. When I try to connect to one of them it never connects, it keeps disconnecting. After a little bit it asks for the password again but its already filled in correctly. If I hit okay it will do the exact same thing again. So does anyone know how I can get this fixed? INFO: Computer: HP Pavilion dv6t-6b00 CTO Quad Edition Entertainment Notebook PC Network Card: Intel® Centrino® Wireless-N 1000 OS: Ubuntu 12.04.1 (x64) dual booting with Windows 7 (x64) (*Not using Wubi*) Wireless Card Driver: iwlwifi UPDATE: I was about to reinstall with the DVD I made with the ISO from the official source but discovered the same issue happens on the disc's Ubuntu preview feature. I still was unable to fix it as before. I also tried the Xubuntu demo, and the same. Re installing the driver hasn't worked either.

    Read the article

  • Computer becomes unreachable on lan after some time

    - by Ashfame
    I work on my laptop and ssh into my desktop. I use a lot of key based authentication for many servers for work but recently I couldn't login because ssh would pick up and try all the keys and it stops trying before ultimately falling back to password based login. So right now I am using this command: ssh -X -o PubkeyAuthentication=no [email protected] #deskto The issue is after sometime the desktop would just become unreachable from laptop. I won't be able to open its localhost through IP and today I tried ping'in it and found a weird thing. Instead of 192.168.1.4, it tries to ping 192.168.1.3 which I am sure is the root cause as it just can't reach 192.168.1.4 when its actually trying for 192.168.1.3 Ping command output: ashfame@ashfame-xps:~$ ping 192.168.1.4 PING 192.168.1.4 (192.168.1.4) 56(84) bytes of data. From 192.168.1.3 icmp_seq=1 Destination Host Unreachable From 192.168.1.3 icmp_seq=2 Destination Host Unreachable From 192.168.1.3 icmp_seq=3 Destination Host Unreachable From 192.168.1.3 icmp_seq=4 Destination Host Unreachable From 192.168.1.3 icmp_seq=5 Destination Host Unreachable From 192.168.1.3 icmp_seq=6 Destination Host Unreachable From 192.168.1.3 icmp_seq=7 Destination Host Unreachable From 192.168.1.3 icmp_seq=8 Destination Host Unreachable From 192.168.1.3 icmp_seq=9 Destination Host Unreachable ^C --- 192.168.1.4 ping statistics --- 10 packets transmitted, 0 received, +9 errors, 100% packet loss, time 9047ms pipe 3 Also the ping command message comes in multiple and not one by one. (izx answer's the weirdness I thought there was in ping command.) I did check for desktop, its local IP is still the same, so something is going on in my laptop. Any ideas? P.S. - Laptop runs Ubuntu 12.04 & Desktop runs Ubuntu 11.10 Laptop is connected through wifi to router and Desktop is connected through LAN to router. Update: Even after setting up static IP leases in router settings, I again ran into this issue.

    Read the article

  • Proxy authentication box not showing (sometimes)

    - by zerologiko
    I'm behind a proxy that require authentication by means of user/pass. I'm using Ubuntu 11.04, I think the proxy is "Squid". Usually everything works fine, that means that the browser shows me the window to insert proxy user/pass and I can navigate. The problem: Sometimes the browser refuse to show the authentication windows and if I wait enough it gives me an error like: Errore 130 (net::ERR_PROXY_CONNECTION_FAILED) Even if I restart, disconnect, the situation doesn't change. BUT on Windows the network (and the proxy) works.. So, bottomline what I know is: the network is working (though only on Windows) the Ubuntu configuration is ok (because i can navigate most days) The problems resolves itself in a few hours but I don't understand why. Some hints? Thanks in advance! Andrea

    Read the article

  • how to map a network drive [duplicate]

    - by acquacheta
    This question already has an answer here: Correct way of mounting a Windows share 1 answer I hope someone can help me.. I'm trying to connect with my university remote filestore, but I can't make it work.. Here is explained what to do on Windows or Mac, and here I found a guide about how to do it with ubuntu, but it's not working to me (at the end of all the steps, I can't access to the mounted folder). I can access to the storage through Konqueror (I'm using KDE), but I would like to access to it also without it. Any suggestion?

    Read the article

  • why does our network printer not show up on some of our macs, but does show up on others? [on hold]

    - by peter
    We lost power in our building and now cannot get our HP laser jet 5200 to be recognized by half of our computers. We are all Macs, some running OS 10.7.5 can see the printer, others running 10.7.5 cannot, and those running 10.8.5 and 10.9 cannot. We've re-booted the router, turned off and on printer and macs—no go. The printer displays an IP address (dynamically assigned) but we can't access it. Tried to see it using CUPS—same story, can see it on some systems, not on others. Any thoughts?

    Read the article

  • Unable to install openjdk7 from terminal [closed]

    - by Adil
    Possible Duplicate: How can I fix a 404 Error using a PPA? Update manager generates 404 error while attempting update. Will not update When i tried to install jdk from following command: sudo apt-get install openjdk-7-jdk Following error was displayed: Err http://us.archive.ubuntu.com/ubuntu/ precise-updates/universe openjdk-7-jre-lib all 7u7-2.3.2-1ubuntu0.12.04.1 404 Not Found [IP: 91.189.91.15 80] E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing?

    Read the article

  • WiFi on Ubuntu 12.04 custom: downloading unbearably slow

    - by Mark
    iwconfig reports 11 Mbps, yet I've seen as low as <1 KBps. This is the latest in my laundry list of Ubuntu problems in a dual-boot machine (cyberpowerpc custom, intel i7-3820, nvidia gtx 570). I received it two days ago, Windows 7 running fine, still having problems with Ubuntu. The browsing is intermittent but unacceptable. e.g. I could get to this site last night but I couldn't post this question. The downloading is unbearably slow, I can't download anything or install any packages because the speed is so slow. e.g. I am trying to install vim which is inexplicably missing from my 12.04 install (add another one to the problems list) and my download speed reported in the terminal was 241 B/s. Yes, bytes. iwconfig reports 11 Mbps, which further adds to the confusion. User@ubuntu:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:39:76:2C:A1 Bit Rate=11 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:54 Invalid misc:18 Missed beacon:0 eth0 no wireless extensions. Any ideas? I see this is a problem a lot of people, but none of the on line solutions have worked for me so far. e.g. one site recommends editing the ath9k.conf file in /etc/modprobe.d, yet this file isn't even in the folder: User@ubuntu:/$ cd etc/modprobe.d User@ubuntu:/etc/modprobe.d$ ls alsa-base.conf blacklist-oss.conf blacklist-ath_pci.conf blacklist-rare-network.conf blacklist.conf blacklist-watchdog.conf blacklist-firewire.conf dkms.conf blacklist-framebuffer.conf nvidia-current_hybrid.conf blacklist-modem.conf nvidia-graphics-drivers.conf I think the nvidia gpu might be mucking things up. I had the "blinking cursor" problem when installing in the first place, and then I had the monitor out of range problem as well. I have my faithful Asus laptop, which is running Ubuntu 12.04 just fine. The only difference is executing host -t SOA local in the terminal gives User@ubuntu:~$ host -t SOA local local has SOA record local. nobody.localhost. 42 86400 43200 604800 10800 in my new machine, and the command reports Host local. not found in the laptop. Help would be most welcome, as I am in danger of reverting back to Windows. I'm seriously considering it. Sorry for the length, trying to show my effort in resolving the issue and include terminal snippets that might be helpful.

    Read the article

  • How do I access an external drive mounted on a machine on my own network?

    - by avilella
    I've got one desktop computer Ubuntu 11.04 with an external USB drive mounted on it on the home WRT54L Linux network (192.168.0.2), and when I arrive at home with my laptop, I want to be able to mount the external USB drive from my Ubuntu 11.04 laptop (192.168.0.3) to the desktop, without having to unplug it from the desktop, that is accessing it. Is it possible to send a remote mount command to the desktop usb drive from my laptop? Ideally something that creates a local mountpoint I can just call locally from the programs installed in my laptop, like: username@laptop ~ ./myprograminlaptop /my/file/which/is/actually/on/the/desktop/file.txt

    Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >