Search Results

Search found 31311 results on 1253 pages for 'oracle product info'.

Page 753/1253 | < Previous Page | 749 750 751 752 753 754 755 756 757 758 759 760  | Next Page >

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• Mac Mavericks, ngircd localhost works, private IP doesn't

  - by user221945

  I have configured ngircd to listen on my private ip address. It doesn't. Localhost works fine. Configuration test: ngIRCd 21-IDENT+IPv6+IRCPLUS+SSL+SYSLOG+TCPWRAP+ZLIB-x86_64/apple/darwin13.2.0 Copyright (c)2001-2013 Alexander Barton () and Contributors. Homepage: http://ngircd.barton.de/ This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Reading configuration from "/opt/local/etc/ngircd.conf" ... OK, press enter to see a dump of your server configuration ... [GLOBAL] Name = irc.bellbookandpistol.com AdminInfo1 = Jaedreth AdminInfo2 = San Diego County CA, US AdminEMail = [email protected] HelpFile = /opt/local/share/doc/ngircd/Commands.txt Info = Server Info Text Listen = 10.0.1.5,127.0.0.1 MotdFile = MotdPhrase = "Welcome to irc.bellbookandpistol.com" Password = PidFile = Ports = 6667 ServerGID = wheel ServerUID = root [LIMITS] ConnectRetry = 60 IdleTimeout = 0 MaxConnections = 0 MaxConnectionsIP = 6 MaxJoins = -1 MaxNickLength = 9 MaxListSize = 0 PingTimeout = 120 PongTimeout = 20 [OPTIONS] AllowedChannelTypes = #&+ AllowRemoteOper = no ChrootDir = CloakHost = CloakHostModeX = CloakHostSalt = kBih5mu\kVI!DC6eifT(hd4m/0'zb/=: CloakUserToNick = no ConnectIPv4 = yes ConnectIPv6 = no DefaultUserModes = DNS = yes IncludeDir = /opt/local/etc/ngircd.conf.d MorePrivacy = no NoticeAuth = no OperCanUseMode = no OperChanPAutoOp = yes OperServerMode = no RequireAuthPing = no ScrubCTCP = no SyslogFacility = local5 WebircPassword = [SSL] CertFile = CipherList = HIGH:!aNULL:@STRENGTH DHFile = KeyFile = KeyFilePassword = Ports = [OPERATOR] Name = [REDACTED] Password = [REDACTED] Mask = [CHANNEL] Name = #BBP Modes = tnk Key = MaxUsers = 0 Topic = Welcome to the Bell, Book and Pistol IRC Server! KeyFile = As you can see, it should be listening on 10.0.1.5, but it isn't. After turning on Apache manually, port 80 works on 10.0.1.5, but port 6667 doesn't. It only works on localhost. Is there some terminal command I could use or some config file I could edit to get this to work?

  Read the article

• Http-Only cookies in WebLogic: what versions support them/how and why are they supported?

  - by John

  We want to make all cookies set by our webapp http-only. I only have a basic understanding of the benefits of doing this but I'm told by security people that it's a Good Thing (tm) Our app is running under JDK1.6.05 and WebLogic10.3.0 After way too much digging around Oracle's website for documentation, I've found good evidence that the first version of WebLogic to support http-only cookies is 10.3.1. By "support," I mean the cookie-http-only deployment-descriptor element. Before we go about upgrading, I'd be nice to have these questions answered: 1a) Is it accurate that WL10.3.1 is the first version to support http-only cookies and that we're out of luck with 10.3.0? 1b) If we do indeed need to upgrade, is there an easy to do so under Windows? I've heard people mention an "upgrade jar" that you just stick in the classpath but I can't find any mention of this by Oracle. Does an easy way exist, or do we need to do a full-install of the new version? 2) What does the cookie-http-only deployment-descriptor element do when enabled? Will it ensure all cookies set by the application have an http-only=true attribute? Will it do more or less? Is there anything I'll have to do programmatically? 3) Is there anything in general I should know about http-only cookies, getting my web app to take advantage of them, or other security concerns?

  Read the article

• SQuirreL Client: Opening up a table in a separate tab

  - by Dalin Seivewright

  I've switched to SQuirrel Client to view an Oracle database with a variety of tables. At any given time, I need to look at the contents of several related tables at the same time. The problem is that, at least by default, SQuirrel Client does not open up multiple tables at a time. When you click on a different Table object, the main view is refreshed with newly selected table data. Oracle's SQLDeveloper (which I am trying to move away from) did this by default if I recall, but there was an option to "freeze" panes. Does a similar option exist in SQuirrel Client? I do not require the ability to view the contents of two different tables on the same screen (i.e. a split view) but I would like the ability to have tabs for each table so I can quickly switch between each table view rather then having to find the table in the table list over and over again. Note: I am using this in a professional capacity but if it does not "belong" here then I suppose it could be moved to superuser.

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• Problems Installing slapd On Ubuntu Server 11.10

  - by Zach Dziura

  I know that there's a Ubuntu-specific StackExchange website, but I thought that I'd ask here because it's a server-specific question. If I'm wrong in my logic... Well, you people are better at this than I am! O=) On with the show! I'm in the process of installing Oracle Database 11g R2 Standard Edition onto Ubuntu Server 11.10. I found a guide on the Oracle Support Forums that walks you through the process fairly easily. Unfortunately, I'm running into issues installing one particular dependency: slapd. When I go to install it, I get this error message: (Reading database ... 64726 files and directories currently installed.) Unpacking slapd (from .../slapd_2.4.25-1.1ubuntu4.1_amd64.deb) ... Processing triggers for man-db ... Processing triggers for ufw ... Processing triggers for ureadahead ... Setting up slapd (2.4.25-1.1ubuntu4.1) ... Usage: slappasswd [options] -c format crypt(3) salt format -g generate random password -h hash password scheme -n omit trailing newline -s secret new password -u generate RFC2307 values (default) -v increase verbosity -T file read file for new password Creating initial configuration... Loading the initial configuration from the ldif file () failed with the following error while running slapadd: str2entry: invalid value for attributeType olcRootPW #0 (syntax 1.3.6.1.4.1.1466.115.121.1.15) slapadd: could not parse entry (line=1051) dpkg: error processing slapd (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: slapd E: Sub-process /usr/bin/dpkg returned an error code (1) After much Google searches and forum trolling, I have yet to find a definitive answer as to what's going wrong. The error messages seem straight forward enough, but I have no idea how to debug this. Can anyone offer some assistance? Again, if I'm asking in the wrong place, I apologize. If I'm indeed asking properly, then thank you for any and all help!

  Read the article

• Hadoop initscript askes password

  - by Ramesh

  I have installed hadoop on my ubuntu 12.04 single node .I am trying to execute an init script to make the hadoop run on start up but it asks password every time i execute. #!/bin/sh ### BEGIN INIT INFO # Provides: hadoop services # Required-Start: $network # Required-Stop: $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Description: Hadoop services # Short-Description: Enable Hadoop services including hdfs ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HADOOP_BIN=/home/naveen/softwares/hadoop-1.0.3/bin NAME=hadoop DESC=hadoop USER=naveen ROTATE_SUFFIX= test -x $HADOOP_BIN || exit 0 RETVAL=0 set -e cd / start_hadoop () { set +e su $USER -s /bin/sh -c $HADOOP_BIN/start-all.sh > /var/log/hadoop/startup_log case "$?" in 0) echo SUCCESS RETVAL=0 ;; 1) echo TIMEOUT - check /var/log/hadoop/startup_log RETVAL=1 ;; *) echo FAILED - check /var/log/hadoop/startup_log RETVAL=1 ;; esac set -e } stop_hadoop () { set +e if [ $RETVAL = 0 ] ; then su $USER -s /bin/sh -c $HADOOP_BIN/stop-all.sh > /var/log/hadoop/shutdown_log RETVAL=$? if [ $RETVAL != 0 ] ; then echo FAILED - check /var/log/hadoop/shutdown_log fi else echo No nodes running RETVAL=0 fi set -e } restart_hadoop() { stop_hadoop start_hadoop } case "$1" in start) echo -n "Starting $DESC: " start_hadoop echo "$NAME." ;; stop) echo -n "Stopping $DESC: " stop_hadoop echo "$NAME." ;; force-reload|restart) echo -n "Restarting $DESC: " restart_hadoop echo "$NAME." ;; *) echo "Usage: $0 {start|stop|restart|force-reload}" >&2 RETVAL=1 ;; esac exit $RETVAL Please tell me how to run hadoop without entering password.

  Read the article

• Graphite not running

  - by River

  I'm currently trying to install graphite 0.9.9 on a gentoo box using these instructions from the graphite wiki. Essentially, it fronts graphite using apache and mod_wsgi. Everything seems to have gone well, except that apache / the graphite webapp never seem to return a response to the web browser (the browser continuously waits to load the page). I've turned on the graphite debug info, but the only message in the log files is this, repeated over and over again in info.log (with the pid always changing): Thu Feb 23 01:59:38 2012 :: graphite.wsgi - pid 4810 - reloading search index These instructions have worked for me before to set up graphite on an Ubuntu machine. I suspect that mod_wsgi is dying, but I have confirmed that mod_wsgi works fine when not serving the graphite webapp. This is what my graphite.conf vhost file looks like: WSGISocketPrefix /etc/httpd/wsgi/ <VirtualHost *:80> ServerName # Server name DocumentRoot "/opt/graphite/webapp" ErrorLog /opt/graphite/storage/log/webapp/error.log CustomLog /opt/graphite/storage/log/webapp/access.log common # I've found that an equal number of processes & threads tends # to show the best performance for Graphite (ymmv). WSGIDaemonProcess graphite processes=5 threads=5 display-name='%{GROUP}' inactivity-timeout=120 WSGIProcessGroup graphite WSGIApplicationGroup %{GLOBAL} WSGIImportScript /opt/graphite/conf/graphite.wsgi process-group=graphite application-group=%{GLOBAL} WSGIScriptAlias / /opt/graphite/conf/graphite.wsgi Alias /content/ /opt/graphite/webapp/content/ <Location "/content/"> SetHandler None </Location> # XXX In order for the django admin site media to work you # must change @DJANGO_ROOT@ to be the path to your django # installation, which is probably something like: # /usr/lib/python2.6/site-packages/django Alias /media/ "/usr/lib64/python2.6/site-packages/django/contrib/admin/media/" <Location "/media/"> SetHandler None </Location> # The graphite.wsgi file has to be accessible by apache. It won't # be visible to clients because of the DocumentRoot though. <Directory /opt/graphite/conf/> Order deny,allow Allow from all </Directory> </VirtualHost>

  Read the article

• ubuntu VM not detecting CDdrives

  - by Mirage

  Ihave insatlled ubuntu 10.4 on my compuer with 6 cd drives. Now initiallyi had window server 2008 and i had to install marvel raid sata controller and then my window detected all 6 drives. Now ubuntu is detecting only 3 drives and i have not found marvell drivers for ubuntu bt i have drives for window 2008. Now my question is if i have vrtual machine inside ubuntu using vmware workstation and i install that driver. then can VM dtect thse 6 drives or host has to detect those drives first to make VMs use that Ubuntu shows this thing from terminal *-cdrom:0 description: DVD-RAM writer product: DVDRAM GSA-H10N vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/cdrom2 logical name: /dev/cdrw2 logical name: /dev/dvd2 logical name: /dev/dvdrw2 logical name: /dev/scd0 logical name: /dev/sr0 version: JL10 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD writer product: DVDRRW GWA-4164B vendor: HL-DT-ST physical id: 0.1.0 bus info: scsi@0:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: 1.01 serial: [HL-DT-STDVDRRW GWA-4164B1.0105/05/12 capabilities: removable audio cd-r cd-rw dvd dvd-r configuration: ansiversion=5 status=nodisc Is t detecting all drives or thise local names just same

  Read the article

• Shell wrong encoding

  - by csch

  Somehow I managed to screw up my shell-encoding. An example: root§server:ç£ cat --help Usage: cat ¡OPTION¿... ¡FILE¿... Concatenate FILE(s), or standard input, to standard output. -A, --show-all equivalent to -vET -b, --number-nonblank number nonempty output lines -e equivalent to -vE -E, --show-ends display $ at end of each line -n, --number number all output lines -s, --squeeze-blank suppress repeated empty output lines -t equivalent to -vT -T, --show-tabs display TAB characters as ^I -u (ignored) -v, --show-nonprinting use ^ and M- notation, except for LFD and TAB --help display this help and exit --version output version information and exit With no FILE, or when FILE is -, read standard input. Examples: cat f - g Output f's contents, then standard input, then g's contents. cat Copy standard input to standard output. Report cat bugs to bug-coreutils§gnu.org GNU coreutils home page: <http://www.gnu.org/software/coreutils/> General help using GNU software: <http://www.gnu.org/gethelp/> For complete documentation, run: info coreutils 'cat invocation' root§server:ç£ It should look like: root@server:~# cat --help Usage: cat [OPTION]... [FILE]... Concatenate FILE(s), or standard input, to standard output. -A, --show-all equivalent to -vET -b, --number-nonblank number nonempty output lines -e equivalent to -vE -E, --show-ends display $ at end of each line -n, --number number all output lines -s, --squeeze-blank suppress repeated empty output lines -t equivalent to -vT -T, --show-tabs display TAB characters as ^I -u (ignored) -v, --show-nonprinting use ^ and M- notation, except for LFD and TAB --help display this help and exit --version output version information and exit With no FILE, or when FILE is -, read standard input. Examples: cat f - g Output f's contents, then standard input, then g's contents. cat Copy standard input to standard output. Report cat bugs to [email protected] GNU coreutils home page: <http://www.gnu.org/software/coreutils/> General help using GNU software: <http://www.gnu.org/gethelp/> For complete documentation, run: info coreutils 'cat invocation' root@server:~# I have no clue what went wrong, do you have any ideas?

  Read the article

• Where do vendors publish internal transfer rates of HDDs?

  - by red888

  So I've started to dig into storage fundamentals and found that in order to calculate the IOPS of a HDD you need to know the internal transfer rate of the drive (time it takes data to move from the platters to internal disk's cache). I went on newegg and even a few vendor sites and could not find this info published for any HDDs. Is it sometimes called something else? Take this link to a seagate HDD for instance. Nowhere do I see "internal transfer rate", but I do see something called "Sustained Data Rate OD"- is that the same thing? Just so you know where I'm getting this info (Book: "Information Storage and Management Storing, Managing..."): Consider an example with the following specifications provided for a disk: The average seek time is 5 ms in a random I/O environment; therefore, T = 5 ms. Disk rotation speed of 15,000 revolutions per minute or 250 revolutions per second — from which rotational latency (L) can be determined, which is one-half of the time taken for a full rotation or L = (0.5/250 rps expressed in ms). 40 MB/s internal data transfer rate, from which the internal transfer time (X) is derived based on the block size of the I/O — for example, an I/O with a block size of 32 KB; therefore X = 32 KB/40 MB. Consequently, the time taken by the I/O controller to serve an I/O of block size 32 KB is (TS) = 5 ms + (0.5/250) + 32 KB/40 MB = 7.8 ms. Therefore, the maximum number of I/Os serviced per second or IOPS is (1/TS) = 1/(7.8 × 10^-3) = 128 IOPS.

  Read the article

• Master File Table Corrupt, any way to save data?

  - by domen

  hi. I've used search, but none of the results match my problem so I didn't have to ask separate question. I've Installed Windows 7 RTM recently and since then partitions located on one of my HDDs have gone "crazy". They used to "freeze" and didn't open in explorer for some time (minute or two, usually), sometimes all partitions of the drive wouldn't show until reboot and finally, one of those partitions started showing "disk structure is corrupted and unreadable" warning, it appeared in Disk Management window as RAW and chkdsk showed "mft corrupt". There were no important data on the partition and I didn't have enough time to analyze the problem at the moment, so I just reformatted it and ran antivirus scan on system. After that problem settled for some time, but yesterday the problematic HDD vanished again from the system. After reboot chkdsk identified mft of four partitions corrupt and now they are all in same conditions as the above mentioned one. But the difference is that the files stored in them are extremely important. and just for info: I upgraded from Win7 build 7077, but had some performance issues, so I reformatted system drive and installed fresh Win7 RTM on it. I've downloaded TestDisk and it shows all the partitions marked as NTFS (not RAW) and my knowledge of the program wasn't sufficient to obtain any other info from it :-) and the images that could help describe the problem (sorry, I'm not allowed to post images and more than one hyperlink): http:// img22.imageshack.us/img22/5909/chkdskz.jpg http:// img198.imageshack.us/img198/5576/computeray.jpg I'm interested, is there a way to let me restore the MFT or just access files so I can backup them before reformatting the drive. Thanks for your time. :) P.S. my reformatted drive is showing no problems, could there be a problem with windows 7 itself? I googled, but with no results.

  Read the article

• Windows XP Loading Problem

  - by Sadeq Dousti

  Sometimes, my Windows XP does not load correctly. It shows the login screen, and when I click my username, it load the desktop background, but the Explorer does not show up. So, I cannot see the icons on the desktop, the start menu, etc. If I press Ctrl+Alt+Del to show Task Manager, I can run programs (like media player or browser) from File--New Task (Run...). Also, in the Task Manager, I see Explorer.exe running. I tried to kill and re-run it, but nothing happens. I used Sysinternals Process Explorer to see if there were any odd process or odd behavior, but nothing was fishy. After several restarts, the system finally worked as expected. But this is not permanent: Sometimes, when I restart the system, it works just as described above (Explorer does not show up). But sometimes it works normally. I used Kaspersky to search for viruses, but nothing showed up. I think the info presented above is not enough to pinpoint the problem. Yet you might be able to tell me about a tool or something, which I can use to give you more info, or even solve the problem. PS: I can easily use the Safe Mode. It does not seem to suffer from this problem. Hence, I suspect there's some process (service) for which Explorer is waiting, but that process runs into trouble (say a race ondition, or an infinite loop) and so Explorer stalls as well.

  Read the article

• Are SATA II and SATA 3.0 Gbps compatible?

  - by Johnny Maelstrom

  I am trying to check that if I buy a new internal HDD it will work in the NAS I am buying. Currently I'm confused about naming schemes and once that is resolved whether there is compatibility. I will gladly author this question to be more general if there is not already an article helping with the confusion of SATA naming and standards. I see similar, but not identical questions and will accept this as a duplicate if thought as such. The specifications on the eCommerce site for the NAS says, "Controller Interface Type Serial ATA-150", the product home page for the manufacturer says, "Compatible with SATA and SATA II HDD". The specifications on the eCommerce site for the hard drives say, "Interface Type Serial ATA-300", the product home page for the manufacturer says, "Interface SATA 3.0 Gbps" Wikipedia says many things about different naming conventions, the closest being, "SATA II 3.0 Gbit/s, which was colloquially referred to as "SATA 3G" [bps] or "SATA 300" [MB/s] since 1.5 Gbit/s SATA I and 1.5 Gbit/s SATA II were referred to as both "SATA 1.5G" [b/s] or "SATA 150" [MB/s]). Therefore, they will operate with negligible differences between them." Are SATA II and SATA 3.0 Gbps the same? I feel I'm tantalisingly close to getting a definitive answer here before I purchase, but really want to clear up these naming schemes.

  Read the article

• Mac updated just now, postgres now broken

  - by user52224

  I run postgres 9.1 / ruby 1.9.2 / rails 3.1.0 on a maxbook air for local dev. It's all been running smoothly for months, (though this is the first time I've done development on a mac.) It's a macbook air from last year, and today I got the mac osx software update message as I have a few times before, and my system downloaded approx 450mb of updates and restarted. It now says it's on OSX 10.7.3. Point is, postgres has stopped working, when I start my thin server (mirror heroku cedar) as normal, and then browse to my rails app I get: PG::Error could not connect to server: Permission denied Is the server running locally and accepting connections on Unix domain socket "/var/pgsql_socket/.s.PGSQL.5432"? What happened? After browsing around a few questions I'm still confused, but here's some extra info: Running psql from command line gives same error I can run pgadmin 3 and connect via it and run SQL no problems Running which psql shows the version as /usr/bin/psql I created a PostgreSQL user back when I got the mac (it's always been on lion) I've no idea why, almost certainly I was following a tutorial which I neglected to store in my notes. Point is I am aware there is a _postgres user as well. I know it's rubbish, but apart from a note on passwords, I don't have any extra info on how I configured postgres - though the obvious implication is that I did not use the _postgres user. Anyone have suggestions or information on what might have changed / what I can try to debug and fix? Thanks. Edit: Playing around based on this question and answer: http://stackoverflow.com/questions/7975414/check-status-of-postgresql-server-mac-os-x, see this string of commands: $ sudo su postgreSQL bash-3.2$ /Library/PostgreSQL/9.1/bin/pg_ctl start -D /Library/PostgreSQL/9.1/data pg_ctl: another server might be running; trying to start server anyway server starting bash-3.2$ 2012-04-08 19:03:39 GMT FATAL: lock file "postmaster.pid" already exists 2012-04-08 19:03:39 GMT HINT: Is another postmaster (PID 68) running in data directory "/Library/PostgreSQL/9.1/data"? bash-3.2$ exit

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

• Can IP address transfer from person to another after he disconnects from ISP or any other way?

  - by learner

  I have been checking this website that sells a product (health related) and trying to find out if it is a scam site. The site is something.blogspot.in (and not something.blogspot.com, which happens to be a different site altogether). So is it an Indian site? It has a CBox chat box where the owner communicates with customers (or potential ones) for information. The owner shows that his product has worked for people by providing links from a forum (created by him at network54.com) where people have posted positively. One doesn't have to be registered to post on there, but the IP address of the poster gets shown along with the post. According to the owner, IP address is basis of authenticity. I found that many people had different IP addresses on their different posts. The owner has declared the nationalities of the people who posted. When I traced the IP addresses of them with this site, I found that the nationalities provided by the owner were wrong. Is it possible that when a person disconnects himself from an ISP, another person from another country gets his old IP address?

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• Can't mount Linux usb disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata). Added: I did try to mount /dev/sg3 but mount say that its not a block device. (File say Its a character special device). Added output from dmesg: [ 97.454073] usb 7-1: USB disconnect, address 2 [ 105.913055] hub 2-0:1.0: unable to enumerate USB device on port 3 [ 107.048054] usb 2-3: new high speed USB device using ehci_hcd and address 5 [ 107.162900] usb 2-3: New USB device found, idVendor=1b1c, idProduct=1ab8 [ 107.162903] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5 [ 107.162906] usb 2-3: Product: CSSD-R60GB2 [ 107.162908] usb 2-3: Manufacturer: Corsair [ 107.162910] usb 2-3: SerialNumber: 10111441000000990069 [ 107.167651] scsi7 : usb-storage 2-3:1.0 [ 108.195543] scsi 7:0:0:0: Direct-Access Corsair CSSD-R60GB2 PQ: 1 ANSI: 0 [ 108.197732] scsi 7:0:0:0: Attached scsi generic sg3 type 0

  Read the article

• Why am I not able to create a backup plan for TFS?

  - by noocyte

  I am trying to create a backup plan using the TFS Power Tools but I keep running into this error message: I have checked that the account has Full Control on the share, I can edit, create and delete files there. From the log: [Info @07:15:00.403] Starting creating backup test validation [Error @07:15:00.700] Microsoft.SqlServer.Management.Smo.FailedOperationException: Backup failed for Server 'WMSI003714N\SqlExpress'. ---> Microsoft.SqlServer.Management.Common.ExecutionFailureException: An exception occurred while executing a Transact-SQL statement or batch. ---> System.Data.SqlClient.SqlException: Cannot open backup device '\\wmsi003714n\sql dump\Tfs_Configuration_20100910091500.bak'. Operating system error 5(failed to retrieve text for this error. Reason: 1815). BACKUP DATABASE is terminating abnormally. at Microsoft.SqlServer.Management.Common.ConnectionManager.ExecuteTSql(ExecuteTSqlAction action, Object execObject, DataSet fillDataSet, Boolean catchException) at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) --- End of inner exception stack trace --- at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(String sqlCommand, ExecutionTypes executionType) at Microsoft.SqlServer.Management.Common.ServerConnection.ExecuteNonQuery(StringCollection sqlCommands, ExecutionTypes executionType) at Microsoft.SqlServer.Management.Smo.ExecutionManager.ExecuteNonQuery(StringCollection queries) at Microsoft.SqlServer.Management.Smo.BackupRestoreBase.ExecuteSql(Server server, StringCollection queries) at Microsoft.SqlServer.Management.Smo.Backup.SqlBackup(Server srv) --- End of inner exception stack trace --- at Microsoft.SqlServer.Management.Smo.Backup.SqlBackup(Server srv) at Microsoft.TeamFoundation.PowerTools.Admin.Helpers.BackupFactory.TestBackupCreation(String path) [Error @07:15:00.731] !Verify Error!: Account GROUPINFRA\SA-NO-TeamService failed to create backups using path \\wmsi003714n\sql dump [Info @07:15:00.731] "Verify: Grant Backup Plan Permissions\Root\VerifyDummyBackupCreation(VerifyTestBackupCreatedSuccessfully): Exiting Verification with state Completed and result Error" Any ideas?

  Read the article

• VCL - configuration for Magento and Varnish 3.0.2

  - by Tomas

  I would like to kindly ask if there's someone who can help me configure Varnish for Magento to reach far more hits. My current ratio from varnishstat is: cache_hit=271 cache_miss=926 I'm kindly asking this because I've googled almost every site related to this theme, but 99.9% of configurations don't work because of outdated code. Details of my set-up: I use Varnish on port 80, Apache on port 81, PageCache as Magento varnish module, APC for PHP speed and Memcached for dynamic caching. Load speed is about 1.5s on home-page (Pingdom.com average results) USA ping & 2.5s Europe. Servers are located in Toronto, Canada. EDIT: This is my full VCL configuration http://pastebin.com/885BzHCs (I just use xxx.xxx.xxx.xxx for my IPs) This is the info from the command (varnishtop -i TxHeader -I Cookie): TxHeader Cookie: frontend=965b5...(*lots of numbers); adminhtml=3ae65...(*lots of numbers); EXTERNAL_NO_CACHE=1 "(*lots of numbers)" is just my adding to the info Any idea how to avoid Varnish hitting this cookies? (If I got correctly the idea about avoiding Vanrish hitting the cookie and not caching the home page). Thank you for any help!

  Read the article

• external drive and CentOS - Reset high speed USB device number

  - by Phil

  I have 2 external drives (3TB) and both will not work with my centOS Box. Tested them in windows ( different machine ) No problems ( 2.6.32-279.9.1.el6.i686 ) dmesg reports: usb 2-2: new high speed USB device number 3 using ehci_hcd usb 2-2: New USB device found, idVendor=2109, idProduct=0700 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: USB 3.0 SATA Bridge usb 2-2: Manufacturer: VIA Labs, Inc. usb 2-2: SerialNumber: 0000000000006121 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access ST3000DM 001-9YN166 CC4B PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] 5860533165 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 06 00 00 sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Attached SCSI disk Tyring to use cfdisk / fdisk / gdisk or even fdisk -l results in the program hanging and dmesg reports: usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd I have the same 2 drives physically installed in the computer via SATA Any Ideas?

  Read the article

• How to remove Media Center from Windows 8

  - by Arabella

  I bought 2 Windows 8 upgrades, 1 for my PC and 1 for my notebook. I added Windows Media Center to my notebook using the free offer in November (side note: the key was emailed to me within 5 minutes, I see many people have been complaining that it takes a few days). Today I decided to add WMC to my PC as well, so I went onto the Microsoft website, same like last time, and I received the email within a few minutes. Once I added WMC, entered the key and the computer rebooted, my activation is now broken: This product key is already being used on another PC. Try a different key or buy a new one. After rereading the product key email, I realised that the WMC key was exactly the same as the one I had received in November for my notebook (I used the same email, i.e. my Microsoft account Outlook email, for both). I didn't think this would be a problem, as on Microsoft's feature pack page it states: ...is limited to five licenses per customer per promotion. So then I decided, I'll just remove WMC from my PC and go back to Windows 8 Pro. So I turned off the WMC feature, PC restarted, activation still broken because my key has been replaced. I then tried to activate it with my original Pro key. The error it gave was that this key cannot be used with this version of Windows, as it is now Windows 8 Pro with Media Center and not Windows 8 Pro anymore. I've searched a bit and it seems the only way to remove it is do a clean install. I tried the Windows 8 Downgrade Helper, which told me I was already running Win 8 Pro when I tried to downgrade, and that I was running Win 8 Pro with Media center when I tried the other option. To sum up: How do I remove Windows Media Center from Windows 8 Pro without having to do a clean install?

  Read the article

• Are there any viable DNS or LDAP alternatives for distributed key/value storage and retrieval?

  - by makerofthings7

  I'm working on a software app that needs distributed decentralized name resolution, and isn't bound to TCP/IP. Or more precisely, I need to store a "key" and look up it's value, and the key may be a string, a number, or any other realistic data type. Examples: With a phone number, look up a name. (or with an area code, redirect to the server that handles that exchange) With an IP Address get a DNS name, or a Whois contact (string value) With a string, get an IP, ( like a DNS TXT or SRV record). I'm thinking out of the box here and looking for any software that allows for this. (more info below) Are there any secure, scalable DNS alternatives that have gained notoriety? I could ask on StackOverflow, but think the infrastructure groups would have better insight on this. Edit More info: I'm looking at "Namecoin" the DNS version of Bitcoin, and since that project is faltering, I'm looking at alternative ways to store name-value pairs, with an optional qualifier. I think a name value pair is of global interest is useful, but on a limited scale. Namecoin tried to be too much, and ended up becoming nothing. I'm trying to solve that problem in researching alternatives and applying distributed technologies where applicable. Bitcoin/Namecoin offers a Distributed Hash Table, which has some positive aspects, but not useful for DNS, except for root servers.

  Read the article

• How can I install git on RHEL 6?

  - by JR.Xyza

  I'm trying to install Git on a RHEL6 development server, I have experience with Ubuntu but this is my first time working with RHEL (I'm a developer trying to fill in for a recently departed Linux Sysadmin). I've set up two additional repos (EPEL and IUS) for other packages needed for a Magento install. Output of yum repolist: [root@box]# yum repolist Loaded plugins: product-id, security, subscription-manager Updating certificate-based repositories. repo id repo name status epel Extra Packages for Enterprise Linux 6 - x86_64 7,841 ius IUS for RHEL 6Server - x86_64 135 Most of what I've read indicates a simple 'yum install git' should work with EPEL enabled, but I get the dreaded [root@box]# yum install git Loaded plugins: product-id, security, subscription-manager Updating certificate-based repositories. Setting up Install Process No package git available. Error: Nothing to do Same goes for git-daemon, etc. I've tracked down a number of git RPMs such as this one at repoforge but they require a train of dependencies that seems to never end. I've also toyed with compiling it manually but the rabbit hole to get make working seems to go even deeper. I'm convinced there's a simple oversight somewhere keeping me from being able to install from the EPEL repo, but I'm a rookie at all this. Thanks in advance for help/pointers/additional resources.

  Read the article

< Previous Page | 749 750 751 752 753 754 755 756 757 758 759 760  | Next Page >