Search Results

Search found 11466 results on 459 pages for 'geo ip'.

Page 76/459 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >

  • Switches with large MAC address table?

    - by user1290200
    Does anyone know which switches have a large MAC address table ? I see most switches having only 8K, but we need to store way, way more than that (hundreds of K). I know this may seem odd, but trust me, there's no other way we can make our setup work. The only thing we seem to be able to do is install Juniper routers that store up to 1M addresses, but that will get quite costly and we'd rather avoid doing that.

    Read the article

  • Possible to redirect from HTTPS to HTTP behind load-balancer?

    - by Derek Hunziker
    I have a basic ASP.NET application that sits behind an F5 load-balancer. Incoming SSL requests (over HTTPS) terminate at the load-balancer and all internal communication between the load-balancer and my application servers is unsecure (over HTTP). When a unsecure request comes in, my app is able to use Response.Redirect("https://...") to redirect a secure URL with no problems. However, the other direction appears to be impossible - I cannot redirect from HTTPS to HTTP using Response.Redirect() from my application. The URL remains HTTPS for the client and does not change. Could the F5 be preventing the redirect for ever reaching the client? Is there any special configuration necessary to let this happen?

    Read the article

  • forward same port but for two different IPs (cisco)

    - by Colin
    Hi! I have a cisco running IOS 12.0(25) responding to two different IPs addresses: IP_A and IP_B. Behind this router I also have two different servers: server_A and server_B. What I want is to forward port 22 to both servers, so: IP_A, port22 -> server_A, port22 IP_B, port22 -> server_B, port22 ATM this only works for one of them (server_A), this is my config: interface Ethernet0/0 description Internet ip address IP_A 255.255.255.0 ip address IP_B 255.255.255.0 secondary no ip directed-broadcast ip nat outside no ip mroute-cache no cdp enable ip nat pool pool_A IP_A IP_A netmask 255.255.255.0 ip nat pool pool_B IP_B IP_B netmask 255.255.255.0 ip nat inside source list A pool pool_A overload ip nat inside source list B pool pool_B overload ip nat inside source static tcp server_B 22 IP_B 22 extendable ip nat inside source static tcp server_A 22 IP_A 22 extendable access-list A permit server_A access-list B permit server_B

    Read the article

  • 2 Nics - Same Subnet..Route backup traffic through one of them

    - by Matthewhall58
    I have a windows server and a centos linux server. I want the nightly backup file (targz) that copies to the windows machine to use a different nic so that the main nic is not burdenend with moving the large file. Each server has 2 Nics in it. the network is 10.173.10.0 mask 255.255.255.192 Centos Linux Box: Eth0 is configured with 10.173.10.80 mask 255.255.255.192 gw 10.173.10.65 Eth 1 is configured with 10.173.10.71 mask 255.255.255.192 gw 10.173.10.65 Windows Box Eth 0 is 10.173.10.72 mask 255.255.255.192 gw 10.173.10.65 Eth 1 is 10.173.10.70 mask 255.255.255.192 gw 10.173.10.65 I can ping each machine from each machine. On the linux machine I use the command route add -host 10.173.10.70 dev eth1 but then when i ping 10.173.10.70 it is unreachable..... WHY?

    Read the article

  • How can I do a "Coming Soon" redirect on IIS6 for everyone except a couple specific IPs?

    - by colinodell
    We're about to do some major maintanence on an IIS 6 / ASP (Classic) website. We want all visitors to be redirected to a "Coming Soon" page (or something similar). This should NOT apply to our dev team (operating remotely), so we'd want to specify certain IPs that should have access to the under-construction site. How can this be accomplished in IIS 6? (Using classic ASP if needed)

    Read the article

  • how to fight back attacks on my web service

    - by user12145
    My apache webservice is getting a large quantity of requests over the days, each one with somewhat random login to gain access. I identified about 60 such ips(a few sample below), all belong to google. is there a way to find more information about the origin of the attacker? or should I just block these ips. secondly, should I attempt to block the identified ips subnets(74.125.46.*) as a preventive measure? 72.14.194.65 64.233.172.20 74.125.75.19 72.14.194.33 74.125.46.87 74.125.44.91 74.125.46.91

    Read the article

  • Why would one server be sending DUP ACK packets to one PC, which is responding with HTTP RST packets?

    - by IronicMuffin
    I'm not a network profressional, so please excuse any wrong language. I was debugging why my DNS traffic was a constant 160Kbps on our corporate network. I opened up a wireshark trace, and I see one PC of a coworker broadcasting HTTP [RST] packets to one of our DMZ servers at the rate of 1000 a second. He restarted his machine, and as soon as it went offline, the server started broadcasting [DUP] [ACK] packets, until he came back online. It then resumed the HTTP [RST] packets. Apparently this server has been doing this kind of behavior since it went live. I believe it did this with a printer and an access point as well. Can anyone explain why this behavior is occurring? Any solutions? The initial research was done because there have been "bandwidth issues" and I wonder if this is contributing.

    Read the article

  • How to route traffic via another machine before the default gateway

    - by Rich
    At the moment I have a router on 192.168.0.1, a Linux box on 192.168.0.2 and desktop clients from 192.168.0.3. Everything works with 192.168.0.1 as the default gateway. I'd like to send the traffic from the desktop clients via the Linux box before it goes out through the router so I can sniff the traffic (some of these are wireless connections). Can I set the default gateway to 192.168.0.2 on the desktop clients and then perhaps add some iptables rules to forward this traffic through 192.168.0.1? Quite happy to change the client desktops to another subnet if that makes it easier. Thanks in advance.

    Read the article

  • 1 Computer Pulls Wrong DNS Every Morning

    - by bradenkeith
    One of my users takes his laptop home, connects to his internal network fine. He brings it in every morning and since Monday - every morning it pulls the wrong DNS every time. It pulls 1 DNS: 192.168.1.1 which is the router. The DNS are external IPs. I have several users that take their laptops home and connect to other networks - what could cause this anomaly? He's booting up when he comes in the office and a simple ipconfig /release /renew fixes the issue.

    Read the article

  • Recommend a desktop app to monitor port 80 on servers

    - by busyone
    Hello, I did some googling but was unsuccessful, so I am posting here. I am looking to get an app (preferably free/open source) to monitor my servers on port 80 that would send me an email/text when some predefined timeout triggers. I could probably write something in VB to do this but i am burried with projects, why reinvent the wheel. I know there are services out there that want you to pay $5/month to do so, I was thinking about a Windows app that would sit on my computer and simply monitor predefined list of IPs on port 80. Thanks!

    Read the article

  • My visitors %20 percent can't reachable to my web site

    - by user39110
    Hi, i have dedicated web server and also i hosting www.btgmaslak.com web site. I'm facing a problem about 1 days. My visitors about 20 percent can't reach my web site. I thing this problem occurs because of dns settings. Can you analyze my dns settings and give me suggestions ? thanks http://www.intodns.com/btgmaslak.com

    Read the article

  • Redirect all access requests to a domain and subdomain(s) except from specific IP address? [closed]

    - by Christopher
    This is a self-answered question... After much wrangling I found the magic combination of mod_rewrite rules so I'm posting here. My scenario is that I have two domains - domain1.com and domain2.com - both of which are currently serving identical content (by way of a global 301 redirect from domain1 to domain2). Domain1 was then chosen to be repurposed to be a 'portal' domain - with a corporate CMS-based site leading off from the front page, and the existing 'retail' domain (domain2) left to serve the main web site. In addition, a staging subdomain was created on domain1 in order to prepare the new corporate site without impinging on the root domain's existing operation. I contemplated just rewriting all requests to domain2 and setting up the new corporate site 'behind the scenes' without using a staging domain, but I usually use subdomains when setting up new sites. Finally, I required access to the 'actual' contents of the domains and subdomains - i.e., to not be redirected like all other visitors - in order that I can develop the new site and test it in the staging environment on the live server, as I'm not using a separate development webserver in this case. I also have another test subdomain on domain1 which needed to be preserved. The way I eventually set it up was as follows: (10.2.2.1 would be my home WAN IP) .htaccess in root of domain1 RewriteEngine On RewriteCond %{REMOTE_ADDR} !^10\.2\.2\.1 RewriteCond %{HTTP_HOST} !^staging.domain1.com$ [NC] RewriteCond %{HTTP_HOST} !^staging2.domain1.com$ [NC] RewriteRule ^(.*)$ http://domain2.com/$1 [R=301] .htaccess in staging subdomain on domain1: RewriteEngine On RewriteCond %{REMOTE_ADDR} !^10\.2\.2\.1 RewriteCond %{HTTP_HOST} ^staging.revolver.coop$ [NC] RewriteRule ^(.*)$ http://domain2.com/$1 [R=301,L] The multiple .htaccess files and multiple rulesets require more processing overhead and longer iteration as the visitor is potentially redirected twice, however I find it to be a more granular method of control as I can selectively allow more than one IP address access to individual staging subdomain(s) without automatically granting them access to everything else. It also keeps the rulesets fairly simple and easy to read. (or re-interpret, because I'm always forgetting how I put rules together!) If anybody can suggest a more efficient way of merging all these rules and conditions into just one main ruleset in the root of domain1, please post! I'm always keen to learn, this post is more my attempt to preserve this information for those who are looking to redirect entire domains for all visitors except themselves (for design/testing purposes) and not just denying specific file access for maintenance mode (there are many good examples of simple mod_rewrite rules for 'maintenance mode' style operation easily findable via Google). You can also extend the IP address detection - firstly by using wildcards ^10\.2\.2\..*: the last octet's \..* denotes the usual "." and then "zero or more arbitrary characters", signified by the .* - so you can specify specific ranges of IPs in a subnet or entire subnets if you wish. You can also use square brackets: ^10\.2\.[1-255]\.[120-140]; ^10\.2\.[1-9]?[0-9]\.; ^10\.2\.1[0-1][0-9]\. etc. The third way, if you wish to specify multiple discrete IP addresses, is to bracket them in the style of ^(1.1.1.1|2.2.2.2|3.3.3.3)$, and you can of course use square brackets to substitute octets or single digits again. NB: if you're using individual RewriteCond lines to specify multiple IPs / ranges, make sure to put [OR] at the end of each one otherwise mod_rewrite will interpret as "if IP address matches 1.1.1.1 AND if IP address matches 2.2.2.2... which is of course impossible! However as far as I'm aware this isn't necessary if you're using the ! negator to specify "and is not...". Kudos also to SE: this older question also came in useful when I was verifying my own knowledge prior to my futzing around with code. This page was helpful, as were the various other links posted below (can't hyperlink them all due to spam protection... other regex checkers are available). The AddedBytes cheat sheet's useful to pin up on your wall. Other referenced URLs: internetofficer.com/seo-tool/regex-tester/ fantomaster.com/faarticles/rewritingurls.txt internetofficer.com/seo-tool/regex-tester/ addedbytes.com/cheat-sheets/mod_rewrite-cheat-sheet/

    Read the article

  • How to send email from home ip when the email server isn't a designated outbound mail server allocated to BT Retail customers [on hold]

    - by Mr Shoubs
    (I am sys admin!) I can receive email, but when I try to send an email from my home office via our work email server I get the following reply: Your message did not reach some or all of the intended recipients. Subject: Test Sent: 19/08/2014 17:02 The following recipient(s) cannot be reached: 'Joe Blogs' on 19/08/2014 17:02 Server error: '554 5.7.1 Service unavailable; Client host [my-ip-here] blocked using zen.spamhaus.org; http://www.spamhaus.org/query/bl?ip=my-ip-here' I went to that URL and it says the following: Ref: PBL231588 81.152.0.0/13 is listed on the Policy Block List (PBL) Outbound Email Policy of BT Retail for this IP range: It is the policy of BT Retail that unauthenticated email sent from this IP address should be sent out only via the designated outbound mail server allocated to BT Retail customers. Please consult the following URL for details on how to configure your email client appropriately. http://btybb.custhelp.com/cgi-bin/btybb.cfg/php/enduser/cci/bty_adp.php?p_sid=fPnV4zhj&p_faqid=6876 Removal Procedure Removal of IP addresses within this range from the PBL is not allowed by the netblock owner's policy. Going to this URL just says: This site has been disabled for the time being. Does anyone know what I should do to allow me to send emails from my home ip - the site suggests I can configure my email client? (note that I have configured the client to use smtp authentication)

    Read the article

  • What's the piece of hardware listening on Facebook's or Wikipedia's IP address?

    - by Igor Ostrovsky
    I am trying to understand how massive sites like Facebook or Wikipedia work, for my intellectual curiosity. I read about various techniques for building scalable sites, but I am still puzzled about one particular detail. The part that confuses me is that ultimately, the DNS will map the entire domain to a single IP address, or a handful of IP addresses in the case of round-robin DNS. For example, wikipedia.org has only one type-A DNS record. So, people from all over the world visiting Wikipedia have to send a request to the one IP address specified in DNS. What is the piece of hardware that listens on the IP address for a massive site, and how can it possibly handle all the load coming from the requests for users all over the world? Edit 1: Thanks for all the responses! Anycast seems like a feasible answer... Does anyone know of a way to check whether a particular IP address is anycast-routed, so that I could verify that this really is the trick used in practice by large sites? Edit 2: After more reading on the topic, it appears that anycast is not typically used for dynamic web content. Anycast is usually used for UDP (e.g., DNS lookups), or sometimes for static content. One interesting thing to note is that Facebook uses profile.ak.fbcdn.net to host static content like style sheets and javascript libraries. Each time I ping this name, I get a response from a different IP address. However, I can't tell whether this is anycast in action, or a completely different technique. Back to my original question: as far as I can tell, even a large site will have a single expensive piece of load-balancing hardware listening on its handful of public IP addresses.

    Read the article

  • MPLS basic configuration

    - by Vineet Menon
    I want to test out MPLS VPN in my lab. I have 3 routers. 2 PEs and 1P router, all cisco 2921. Something like this, ----- ---- ----- | PE1 |.1____192.168.1.0____.2| P |.2____192.168.2.0____.1| PE2 | | | | | | | ----- ---- ----- lo0:10.1.1.1 lo0:10.1.1.2 lo0:10.1.1.3 Here's the configuration file for each of them, PE1 router hostname PE1 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! interface Loopback0 ip address 10.1.1.1 255.255.255.255 ! interface GigabitEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.1.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.3 remote-as 100 neighbor 10.1.1.3 update-source Loopback0 neighbor 172.16.1.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.3 activate neighbor 10.1.1.3 send-community extended exit-address-family For P router: hostname P ! no ipv6 cef ip source-route ip cef ! interface Loopback0 ip address 10.1.1.2 255.255.255.255 ! interface GigabitEthernet0/1 ip address 192.168.1.2 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/2 ip address 192.168.2.2 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.2 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 ! For PE2 router: ! hostname PE2 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! ! interface Loopback0 ip address 10.1.1.3 255.255.255.0 ! interface GigabitEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.2.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.3 0.0.0.0 area 0 network 192.168.2.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.1 remote-as 100 neighbor 10.1.1.1 update-source Loopback0 neighbor 172.16.2.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.1 activate neighbor 10.1.1.1 send-community extended exit-address-family ! I am following this article form cisco. But things are not working properly. Any help would be appreciated.

    Read the article

  • remote_addr problem

    - by Andrew Kolvik
    I am using xampp on localhost and when I use _SERVER["REMOTE_ADDR"] it returns ::1 (also does this in phpinfo()). Why does it do this? I want it to return a normal ip address like 127.0.0.1. My operating system is windows vista.

    Read the article

  • SQLite3 Integer Max Value

    - by peterwkc
    Hello to all, what is the maximum value of data type INTEGER in sqlite3 ? How do you store ip address in database ? What is attached ? How to create table which belongs to a specific database using sql ddl? What is this error about ? error while the list of system catalogue : no such table: temp.sqlite_master Unable to execute statement Does sqlite3 text data type supoports unicode? Thanks.

    Read the article

  • how to configure IP cam to stream using right network card?

    - by robin hood
    I have IP cam that supports RTSP streaming. It's connected to router with 2 network cards with IP1 and IP2 addresses. I make 2 connections to IP cam by IP1 and IP2 addresses from the same IP and I need to receive corresponding streams thru correct network card, but both streams (RTP over UDP) go thru IP1. How this can be resolved? I don't know if RTSP server binds UDP sockets to corresponding IP and I don't know what IP stack is in IP cam (weak end system or strong end system). I haven't found anything interesting in router configuration. As I understand, routing table cannot help me cos I'm connected from the same IP, is it right? Also Sorry for incomplete info but it's all I have at the moment. Thanks for your time.

    Read the article

  • Howto check if two hosts are the same

    - by Michael Stoll
    Hi, I just came across an issue, where I had to check if a path points into a windows share. Part of this problem is to check if host A is the same as host B. Where host A and host B can be one of the following {IPv4-Address, IPv6-Address, Hostname, FQDN}. As I do not need to be exact it's enough to resolve and compare the IP-Addresses in my case. But is there, theoretically, a method to check if the hosts are the same?

    Read the article

  • If I'm running my App Engine app on localhost, will I not see a value for X-AppEngine-Country?

    - by Bartholomew
    According to the Release Notes: All user request have an X-AppEngine-Country header which contains the ISO-3166-1 alpha-2 country code for the user, based on the IP address of the client request. My app is running on localhost with the 1.5.1 Java release which contains the X-AppEngine-Country header but I don't seem to be receiving any value for this header in my requests. Do I have to deploy the app to a production instance to test this feature?

    Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >