Search Results

Search found 19382 results on 776 pages for 'multiple'.

Page 76/776 | < Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >

• Third monitor randomly defaults to 640 x 480 on startup

  - by andybaird

  I purchased a PowerColor HD 5770 video card so I could get a third monitor working. I have two widescreen monitors, one attached via HDMI and the other attached via DVI. My third monitor is attached from DisplayPort to VGA (using a passive connector like this one) The third monitor is a 19" Hyundai L90D. I was unable to find any Windows 7 (or Vista for that matter) drivers for the monitor, so it's stuck with "Generic Non-PNP Monitor". It's native resolution is 1280 x 1024. Randomly Windows will boot up in the correct native res, but sometimes it boots up in 640 x 480 res. When it does boot up into 640 x 480 res, the screen resolution slider is stuck and I cannot slide it back to 1280 x 1024. I cannot find a pattern for when or why it will do this, I've tried rebooting five or six times in a row at times to get it to boot into native res, but this doesn't always work.

  Read the article

• Intel motherboard drops HDMI output after Windows boots

  - by Nick

  I have an Intel motherboard (DH67CL) that uses Intel HD 3000 video. It has two video output ports: HDMI and DVI. Both my monitors are DVI, so I have two cables: a DVI-DVI and an HDMI-DVI. If I plug a monitor into just one of these ports, things work fine. But if I plug monitors into each of the ports, the system startup screens show on both monitors, along with the "Starting Windows..." screen, but as soon as the system boots into Windows, the HDMI-connected monitor goes to sleep. When I use the Intel video control panel, the HDMI-connected monitor is not detected. How do I get a dual-monitor setup to work?

  Read the article

• Strange scaling when duplicating monitors with another screen

  - by Aerione

  I can't get two monitors to scale application resolutions the same way. My main monitor works normally. My second monitor however, which is set to duplicate its image onto a TV I have in my room, renders the applications in a far lower resolution than the 1080p I've set it to. Also, the mouse pointer on the second monitor is enormous, it looks 2-3 times bigger than the one on the main monitor. I've checked the "Let me choose one scaling level for all my displays", to no avail. Here are some comparison pictures. Metro on the main monitor: Metro on monitor 2 (set to 1080p and to duplicate on a TV): This issue only seem to arise when I duplicate the monitor onto the TV. Does anyone have any idea of how to solve this?

  Read the article

• Radeon HD 5770 - DisplayPort Problem

  - by Nick Schmit

  I am trying to set up 3 monitors with the Radeon HD 5770 I recieved a few days ago. I have read that I can use 2 DVI ports and an active DisplayPort adapter for a third DVI monitor. I have purchased this adapter: http://www.accellcables.com/products/DisplayPort/DP/dp_dvid.htm I have the two normal DVI monitors working, but when I try to extend the display to the third, I get a message saying the system has detected a problem with the connection through the display port which may limit resolution/refresh rate. I know that all the cables are fine, I have replaced the adapter, the monitors all work, I have tried different monitors through the adapter, and even nothing but the adapter, but I cannot get any monitor to work using it. I am trying to use 2 Dell monitors and an Acer. Have I overlooked something? Is there a compatibiliy issue I missed? Any suggestions as to what I could try? Thanks in advance.

  Read the article

• How can I stop Flash from leaving full-screen mode when it loses focus due to a mouse-click in the o

  - by therefromhere

  On a multi-monitor system, if I'm viewing a full-screen video in Flash on one monitor, clicking the mouse on the other monitor causes Flash to leave full-screen mode and revert to normal size. What's the easiest way of preventing this that works on my version of Flash? My system is Flash 10 (10.0.12.36), in Firefox 3.5 on Windows Vista 64, but I think it affects all current versions. This is very annoying behaviour, but unfortunately, according to this bug report response it seem to be a security feature, rather than a bug: We understand that many users would like fullscreen on one monitor and to be able to interact with your OS on another monitor. However, due to security requirements, we require that Flash and Browser must be the current focus of your OS.

  Read the article

• LCD monitor reports incorrect maximum resolution

  - by SLaks

  I have four 20" Planar 2010M LCD monitors with a maximum resolution of 1600 x 1200 connected to two nVidia video cards (8600 GT and 7600 GS). I'm running Windows Server 2003 x86. Recently, two of the monitors have started mis-reporting their maximum resolution as 1280 x 1024. When this first happened, I used nVidia's Custom Resolutions feature to force the monitors back to 1600 x 1200. Yesterday, however, I upgraded nVidia's video card driver, and ever since, I cannot get the DVI one back to 1600 x 1200. When I add the custom resolution in nVidia's control panel, if I set either the width or the height to even a single pixel more than 1280 x 1024, nothing changes when I click Test (the monitor doesn't even flash black, although after 15 seconds, it flashes black and doesn't change). After adding Does anyone know what the problem is? Is there anything I can do about it?

  Read the article

• emulate fake monitor on windows 7?

  - by Claudiu

  Is there any way to emulate a monitor on Windows 7? I have one physical monitor, and I want Windows to think I have two. I actually don't care whether the second monitor is visible anywhere, or if I can see it - everything rendered there may as well go to the equivalent of /dev/null - but I need Windows to think there is one there. The reason is that I want to run a virtual machine with two monitors with VirtualBox in seamless mode, and it doesn't let me go to seamless mode if there are more virtual monitors than physical ones. I don't need to see the second virtual monitor, but VirtualBox won't just stop displaying it like it did in earlier versions.

  Read the article

• Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

  - by cpm

  I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

  Read the article

• Multi domain on my dedicated server with Apache2

  - by x4vier

  I setup a server with Ubuntu 10.04 server edition. It's works for a long time with a single domain name. Now i want to add another domain wich will pointed to a new directory. I tried to change my Apache2 configuration but it does not seems to work properly. Here is my /etc/apache2/sites-available/default <VirtualHost *:80> DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> <VirtualHost *:80> ServerName mydomain.com ServerAlias www.mydomain.com DocumentRoot /var/www/mydomain </VirtualHost> here is my /etc/hosts 127.0.0.1 localhost **.***.133.29 sd-***.****.fr sd-**** **.***.133.29 mediousgame.com # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback ****::0 ip6-localnet ****: :0 ip6-mcastprefix ****::1 ip6-allnodes ****::2 ip6-allrouters ****::3 ip6-allhosts With this configuration when i try to access to mydomain it redirect to the /var/www/ content. Do you have any idea to redirect to the right folder ?

  Read the article

• One Active Directory, Multiple Remote Desktop Services (Server 2012 solution)

  - by Trinitrotoluene

  What I am trying to do is quite complex, so I figured I'd throw it out to a wider audience to see if anyone can find a flaw. What I am trying to do (as an MSP/VAR) is design a solution that will give multiple companies a session based remote desktop (companies that need to be kept completely seperate), using only a handful of servers. This is how I imagine it at the moment: CORE SERVER - Server 2012 Datacentre (All below are HyperV servers) Server1: Cloud-DC01 (Active Directory Domain Services for mycloud.local) Server2: Cloud-EX01 (Exchange Server 2010 running multi tenant mode) Server3: Cloud-SG01 (Remote Desktop Gateway) CORE SERVER 2 - Server 2012 Datacentre (All below are HyperV servers) Server1: Cloud-DC02 (Active Directory Domain Services for mycloud.local) Server2: Cloud-TS01 (Remote Desktop Session Host for Company A) Server3: Cloud-TS02 (Remote Desktop Session Host for Company B) Server4: Cloud-TS03 (Remote Desktop Session Host for Company C) What I thought about doing was setting up each Organisation in their own OU (perhaps creating their OU structure based on the Excahnge 2010 tenant OU structure so the accounts are linked). Each company would get a Remote Desktop Session Host server that would also serve as a file server. This server would be seperated from the rest on its own range. The server Cloud-SG01 would have access to all these networks and route the traffic to the appropriate network when a client connects and authenticated so they are pushed onto the correct server (Based on session collections in 2012). I won't lie this is something I have come up with quite quickly so there may well be something gapingly obvious that I am missing. Any feedback would be appreciated.

  Read the article

• Linux Twinview : copy window application to both screens

  - by Dom

  I use the SUN Presenter Openoffice Extension with a twinview Ubuntu laptop. it works well : I have the video-projector with my presentation and my laptop screen with the slides (and time...). My problem is when I want to present a mono-screen application, like Firefox, gnome-terminal. It is displayed only on one monitor, which is not really efficient if you want to be interactive. Is there a way to display these types of application on both display and to interact with both ? Thanks

  Read the article

• Windows 7 resizes desktop when I switch of a monitor

  - by Stijn Sanders

  I have a workstation with two monitors and the desktop extended over them. I have a lot of applications open (generally maximized), and I have a personal preference which application is on which monitor (let's say editors on the right, data retrieval and display on the left). I have recently upgraded to a workstation with Windows 7 and when I power off a monitor (typically when going home at the end of the day), the desktop-expand-over-monitors disables and all applications are switched to the main monitor. (Also the taskbar I keep on the left resizes to about one icon's width.) This is highly annoying, since I now spend the first minutes of work each day switching the applications back that were on the monitor on the right. Is there a way to prevent this? (It says no here.) Is there software I could install that can prevent this?

  Read the article

• uname -a gives wrong version of kernel in gentoo?

  - by freedrull

  Hi I'm running gentoo and doing uname -a gives the wrong kernel version. tony@P_P-o ~ $ uname -a Linux P_P-o 2.6.27-gentoo-r8 #12 SMP PREEMPT Sun Nov 8 19:46:59 PST 2009 i686 Genuine Intel(R) CPU T2060 @ 1.60GHz GenuineIntel GNU/Linux Running eix gentoo-sources shows that I have a later version than that installed: tony@P_P-o ~ $ eix gentoo-sources [U] sys-kernel/gentoo-sources Available versions: (2.6.16-r13) 2.6.16-r13!b!s (2.6.25-r9) 2.6.25-r9!b!s (2.6.26-r4) 2.6.26-r4!b!s (2.6.27-r8) 2.6.27-r8!b!s (2.6.27-r10) 2.6.27-r10!b!s (2.6.28-r5) 2.6.28-r5!b!s (2.6.28-r6) 2.6.28-r6!b!s (2.6.29-r5) 2.6.29-r5!b!s (2.6.29-r6) 2.6.29-r6!b!s (2.6.30) ~2.6.30!b!s (2.6.30-r3) ~2.6.30-r3!b!s (2.6.30-r4) 2.6.30-r4!b!s (2.6.30-r5) 2.6.30-r5!b!s (2.6.30-r6) 2.6.30-r6!b!s (2.6.30-r7) 2.6.30-r7!b!s (2.6.30-r8) 2.6.30-r8!b!s (2.6.31) ~2.6.31!b!s (2.6.31-r1) ~2.6.31-r1!b!s (2.6.31-r2) ~2.6.31-r2!b!s (2.6.31-r3) ~2.6.31-r3!b!s (2.6.31-r4) ~2.6.31-r4!b!s {build symlink ultra1} Installed versions: 2.6.27-r8(2.6.27-r8)!b!s(07:48:25 PM 06/19/2009)(-build -symlink) 2.6.28-r5(2.6.28-r5)!b!s(12:35:17 PM 06/08/2009)(-build -symlink) 2.6.29-r5(2.6.29-r5)!b!s(07:44:33 PM 06/19/2009)(-build -symlink) 2.6.30-r6(2.6.30-r6)!b!s(11:14:45 PM 10/02/2009)(-build -symlink) Homepage: http://dev.gentoo.org/~dsd/genpatches Description: Full sources including the Gentoo patchset for the 2.6 kernel tree What gives?

  Read the article

• Different display arrangements for two identical displays

  - by Niels

  I have a MacBook Pro running OSX Lion and two workplaces with identical setups: at both places I have an 27" LED Cinema display. At one workplace my MacBook is on the left side of the external display, and at the other workplace it is on the right. I would like to have two different display arrangements for the two different setups, however, when I change the display arrangements in System Preferences when connected to one display, the arrangement is changed for the other display as well. I used to have a 27" and a 24" Cinema Display, and OSX used to remember the display arrangements for those different displays, but now the displays are identical, so they use the same arrangements setting. Is there any way to tell OSX to handle two identical displays as different ones so I can configure two different arrangements for the two setups?

  Read the article

• Webserver concurrent connections

  - by sri

  Where can I get statistics of concurrent connections that can be handled by Apache and IIS? Which one will serve more requests in peak times? Thank you, Sri

  Read the article

• Can two Identical devices be present on the same bus in any PCI Topology

  - by vaibbhav

  As per the PCI standard, devices are identified on the basis of Vendor Id, Device Id and the bus no. All devices of same type have identical vendor id and device id. If I put two such devices on the same bus say bus 0. How will the PCI Software Subsystem distinguish between the two? If such a case is not possible in PCI, then can such thing be possible through PCI Express Switch?

  Read the article

• I think installing PostFix solved my problem, but it seemed *too* easy

  - by Joel Marcey

  Hi, This is a followup to a serverfault post I made a while ago: http://serverfault.com/questions/21633/how-do-i-target-a-different-mail-server-depending-on-domain-with-exim (More context here too: http://forum.slicehost.com/comments.php?DiscussionID=3806 ) I have a slice/VPS at Slicehost. I basically decided to scrap exim (i.e., purge it), and start anew with my email infrastructure. In case you didn't read any of the above threads, basically my goal was to have a send only mail infrastructure that relays all outgoing email to Google Apps. I also wanted to where email from domain1 (a Wordpress installation) would show it coming from domain1.com and email from domain2 (a normal website) would show it coming from domain2.com. So I decided to give PostFix a try. I literally followed the surprisingly simple instructions here: http://sudhanshuraheja.com/2009/02/slicehost-setup-outgoing-mail-google-apps-postfix/ And voila, all seems to be working as I expected. My email tests show email coming from the proper locations (either domain1 or domain2 depending on where the emails were sent from). But this all seemed too simple to me. So simple, in fact, that I feel that something is amiss. When I installed PostFix according to the instructions in the post above and it worked, I was surprised that I didn't have to specify an SMTP server, a port number, any authentication credentials, etc. My slice is set up such that I have MX records for Google Apps (e.g., ASPMX.L.GOOGLE.COM.) in my DNS settings, but I am not sure if that is why it is working. My email infrastructure knowledge is admittedly limited, but with this am I suspect to: Spammers using my email infrastructure? My emails going to people as spam? Something else sinister? I have actually stopped running PostFix until I understand this better. Thanks!

  Read the article

• nVidia Driver - Laptop is forced as one of my monitors

  - by vaccano

  I am trying to get my nVidia Driver to correctly configure my multi-monitor setup. I have my laptop in a docking station and two monitors hooked up to it. I had an old driver that this worked correctly with. However, that driver was causing a lot of "Deferred Procedure Calls" so I upgraded to a newer driver. But now I am forced to use my Laptop monitor as one of my monitors. Here is the image in the nVida Control Panel: As you can see, both monitors are recognized, but the only options available are to use one of them with the Laptop Display. Any Ideas? I am running Windows XP (latest updates), I have an nVidia Quadro 1500M. I have tried several different driver versions and all the new ones have this issue.

  Read the article

• Second video card (PCI) under Windows 7

  - by dbkk101

  I'm trying to get an old PCI video card (Diamond Stealth 2500) along with a normal PCI-E video card. In BIOS, there is a setting to switch between PEG/PCI or PCI/PEG on startup (PEG is PCI-E Graphics). When I use PCI/PEG only the old PCI card works, when I use the other one, only the new PEG card works. In PEG/PCI mode, Windows 7 recognizes the card and shows it in Device Manager as Standard VGA adapter, but it shows a warning for the device ("This device cannot start. (Code 10)").

  Read the article

• Change Linux Console's Default Monitor

  - by Tim M

  Is there any way to specify which monitor the console is displayed on in Linux? Details: I have a 3 monitor setup with 2 video cards. When I boot the computer, the BIOS displays on the PCI graphics card (which has a small monitor). When starting Linux, the console is displayed on the same monitor. Is there a way to have the console output on a different monitor? I'm using the vesafb framebuffer. I don't see a way in my BIOS to change the default video card.

  Read the article

• ATI Radeon 5850 I cant seem to get 3 monitors up at the same time. 2 Monitors and a HDTV but still.

  - by Jan

  Ive just bought the top end ATI Radeon card with 2 normal monitor ports and a HDMI. The idea was to continue using my dual screen setup as always and to use the last plug, the HDMI on my TV. I got a new 52 inch HD TV with all the necessary bits. This should work fine. But.. in Display Properties I still get only my 2 monitors up as options. Not the Digital TV. When I unplug 1 monitor and restart the computer, I get the TV and the other monitor. But never all 3 at the same time. Why is this ? Where can I go to tell it that I need all 3 screens at the same time. Also I get a message saying my gfx card also gives sound through the HDMI cable.. But the TV tells me its recieving a sound format that it does not understand. Any ideas on that too while were at it ?

  Read the article

• How do I enable an extended desktop across two monitors in Knoppix 6?

  - by Janice

  I want to have an extended desktop that spans two screens, but Knoppix's monitor settings only allow me to mirror but not create an extended desktop. I'm not very good with the command-line but I know how to use apt-get. Is there some package I can download to do this?

  Read the article

• What video card will support 3 monitors with Win7 64 bit

  - by theMezz

  What video card will support 3 monitors with Win7 64 bit I am not a gamer, but do edit photos and would like to use all the Win7 video capabilities and effects. Suggestions for what ONE video card to buy? Thanks, Joe

  Read the article

• Monitor occasionally doesn't display properly

  - by homestead

  Hi, I am using dual monitors, and this behavior has occured on 2 different computers (using the same monitors). When I turn the monitors off, and then on again after a while, 1 monitor turns on, displays the Dell logo etc. but doesn't display the windows login. It is just a blank page, and then the green light turns orange. Turning it on/off many times or just waiting a while eventually results in it working again, but I am very confused why!

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

< Previous Page | 72 73 74 75 76 77 78 79 80 81 82 83  | Next Page >