Search Results

Search found 39497 results on 1580 pages for 'two shoes'.

Page 762/1580 | < Previous Page | 758 759 760 761 762 763 764 765 766 767 768 769  | Next Page >

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• Looking for a laptop with a removable hard drive

  - by anno

  At the moment, I possess a Dell Inspiron 6400. Just removing two screws, I've made the drive removable (look here) and I can pull it off in one second. The new Inspiron and Studio laptops don't support this anymore (the drive is no more on the side but on the back of the laptop). So I’m looking for a new laptop having this kind of feature, or one that can be modded easily. I also need a : Screen = 15" (if possible resolution 1366 x 768 resolution) Core i5-520M Midrange GPU (like an ATI Mobility Radeon HD 5650) Decent battery life minimum fan noise Thanks.

  Read the article

• In TCP/IP terms, how does a download speed limiter in an office work?

  - by TessellatingHeckler

  Assume an office of people, they want to limit HTTP downloads to a max of 40% bandwidth of their internet connection speed so that it doesn't block other traffic. We say "it's not supported in your firewall", and they say the inevitable line "we used to be able to do it with our Netgear/DLink/DrayTek". Thinking about it, a download is like this: HTTP GET request Server sends file data as TCP packets Client acknowledges receipt of TCP packets Repeat until download finished. The speed is determined by how fast the server sends data to you, and how fast you acknowledge it. So, to limit download speed, you have two choices: 1) Instruct the server to send data to you more slowly - and I don't think there's any protocol feature to request that in TCP or HTTP. 2) Acknowledge packets more slowly by limiting your upload speed, and also ruin your upload speed. How do devices do this limiting? Is there a standard way?

  Read the article

• Exchange 2013 - DNS Records for Accepting Multiple Domains

  - by William

  I have an Exchange 2013 server accepting two domains: domain1.com and domain2.com. All of the exchange services (OWA, ECP, POP3, SMTP, etc.) can be found via the address mail.domain1.com. So, in the DNS records for domain1, I have the following entries: MX Record mail.domain1.com A Record mail.domain1.com - (IP Address of Server) CNAME Record autodiscover.domain1.com - mail.domain1.com Now, for domain2.com, how would I set up the DNS records? Would I have the autodiscover just be a cname for autodiscover.domain1.com? Would this allow me to leverage the certificates that I have installed for domain1?

  Read the article

• gcc sandboxing tool - AppArmor / CHROOT jail on Ubuntu 12.04

  - by StuR

  We have a Node application as the front end to a C++ sandboxing tool, which compiles code using gcc and outputs the result to the browser. e.g. exec("gcc -o /tmp/test /tmp/test.cpp", function (error, stdout, stderr) { if(!stderr) { execFile('/tmp/test', function(error, stdout, stderr) {}); } }); This works fine. However, as you can imagine this is a security nightmare if it were to be made public - so I was thinking of two options to protect my stack: 1) A CHROOT jail - but this in itself wouldn't be enough to prevent directory traversal / file access. 2) AppArmor ? So my question is really, how could I protect my stack from any nasties that could come from: A) Compiling unknown code using gcc B) Executing the compiled code

  Read the article

• 2 GPUs (for multi-monitor setup)

  - by A Dwarf

  I have a machine to which I need to connect a second monitor. This machine currently hosts a ATI Radeon HD 4770 with two DVI adapters. The second monitor to be hooked to this machine is a VGA monitor. Until I find a DVI-VGA adpater, I'm thinking installing a second graphics card which does have a VGA adapter, an NVidia card. Can I successfully run both AMD and NVidia cards on this machine? Any specifics I must be aware of, like how to ensure the ATI card to be the main card? Operating system is Windows 7

  Read the article

• DNS protocol message example

  - by virtual-lab

  hello there, I am trying to figure out how to send out DNS messages from an application socket adapter to a DNSBL. I spent the last two days understanding the basics, including experimenting with WireShark to catch an example of message exchanged. Now I would like to query the DNS without using dig or host command (I'm using Ubuntu); how can I perform this action at low level, without the help of these tools in wrapping the request in a proper DNS message format? How the message should be post it? Hex or String? Thanks in advance for any help. Regards Alessandro Ilardo

  Read the article

• Duplicate xserver

  - by hariks0

  When I start my ubuntu pc, just before my login, I receive a message that says "An xserver is already started in display :0. Would you like to try starting xserver in another virtual workspace?". Now If I answer 'No' the message appears again and again. If I say 'Yes' It goes to gnome desktop in virtual desktop 9 [Ctrl+Alt+F9] It was previously available only in [Ctrl+Alt+F7] but now available in both F7 and F9. Now I assume that there are two instances of xserver both in [Ctrl+Alt+F7] and [Ctrl+Alt+F9]. I think by killing one instance of xserver manaually I can disable the message. How do I do this? Thanks in advance.

  Read the article

• Symantec CPS / Backup Exec 11D Service stuck in "Starting" Status

  - by user42289

  I have two Windows 2003 (one is SE, one is SBS) both SP2, both are Virtual Machines of Microsoft Virtual Server 2005 R2. All of a sudden about 2 weeks ago, the Symantec Backup Exec / CPS 11D stopped working on them. One is the Media server, one is our Exchange 2003 Server. There is another copy of CPS on our file server that the service is running fine on. However the one that is fine is not a VM. When I say stop working, the "backup exec continuous protection agent" service is stuck in "starting" status. On the non Exchange server I've tried uninstalling the last Windows Updates that were run some time around the time of failure. I've tried repairing the install of CPS. I've tried uninstalling it and reinstalling. Exact same problem in the end.

  Read the article

• hung up troubleshooting packet discards

  - by Chris Satola

  I realize my question is generic, but hopefully someone may have some guidance for me. My network consists of Cisco switches. I am seeing a significant amount (upwards of millions of packets per day) transmit drops between two switches. One being a 3750 and the other a 3560. The peak throughput of this link is only upper 400Mbps, so it shouldn't be a bandwidth issue. At this point, I am sort of clueless where to look or what tools I can use to determine what packets are dropping and why. I can setup a SPAN port on that link and wireshark it, but I don't know if that could tell me anything. Does anyone have any suggestions? Thanks in advance.

  Read the article

• Alias multiple DNS entries to one Amazon S3 Bucket

  - by Tristan

  I have a bucket on Amazon S3. Lets call it "webstatic.mydomain.com". I have a DNS alias setup for that bucket webstatic.mydomain.com CNAME - web-static.mydomain.com.s3.amazonaws.com. This all works great, however for some rather complicated reasons I now need: webstatic.myOtherDomain.com to point to that same amazon bucket so: webstatic.myOtherDomain.com CNAME - web-static.mydomain.com.s3.amazonaws.com. Fails, as the bucket is not called the same as the referring DNS. Can anyone tell me how to have two different DNS entries pointing to the same amazon bucket?

  Read the article

• Windows Server 2003 not automatically assigning drive letter to external drives

  - by Chris

  My newly rebuilt Windows Server 2003 doesn't automatically assign drive letters to external usb devices. I have to manually open the Disk Management Console and assign it a drive letter every time. It does this with two different drives in all USB ports. I have been doing some reading and I don't have any network drives, I have also already tried USBDLM and it doesn't seem to have made any difference. Specs: ProLiant ML150 G5 with Windows 2003 Enterprise and all updates installed. Any ideas on what I can try to resolve this problem would be greatly appreciated. Chris

  Read the article

• Help with Apache rewriteengine rules

  - by Vinay

  Hello - I am trying to write a simple rewrite rule using the rewriteengine in apache. I want to redirect all traffic destined to a website unless the traffic originates from a specific IP address and the URI contains two specific strings. RewriteEngine On RewriteLog /var/log/apache2/rewrite_kudithipudi.log RewriteLogLevel 1 RewriteCond %{REMOTE_ADDR} ^199\.27\.130\.105 RewriteCond %{REQUEST_URI} !/StringOne [NC, OR] RewriteCond %{REQUEST_URI} !/StringTwo [NC] RewriteRule ^/(.*) http://www.google.com [R=302,L] I put these statements in my virtual host configuration. But the rewriteengine seems to be redirect all requests, whether they match the condition or not. Am I missing something? Thank you. Vinay.

  Read the article

• Network trials and tribulations

  - by MauiWowie

  Hi, I am in the process of setting up a small (two PC's, both running Windows 7) network using a D-link DI-604 router (which acts only as hub, it's not set up in any way). In the Network and 'Sharing Center' in 'Control Panel' I clicked 'Set up a New (Connection or) Network'. All went well up until the moment I attempted to connect one PC with the other (in the 'Connect' dialog I entered the other PC's IP, no pwd). I can use both PC's to connect to and browse the net though, so the router/hub does not seem to be the problem. And I must have done something right, because the other computer shows up in the 'Network Map'. Any and all help is much appreciated!

  Read the article

• Is it possible to have nested libraries in Windows 7?

  - by dr_draik

  My goal is this: I have a library, say it's called Series. I store my series in two different places, one for watched episodes and one for unwatched episodes. Obviously I can simply add the root folder of each location to a series library. What I would prefer to do is have a sub-library within Series for each series, for example: Series \ Lost Lost (Unwatched series) Episode 3 Episode 4 Lost (Watched series) Episode 1 Episode 2 Is there a way to achieve this, or something approximating this (without having a full library for each series)? P.S. I've read the other topic, but I was wondering if there was a possible workaround for this specific need. More out of hope than anything else. ;)

  Read the article

• Why does DBAN crash on my HDDs?

  - by John Watson

  I am using DBAN to erase HDD. DBAN is loaded from a CD and BIOS Boot order has been set to favour CD drive. On starting laptop, system boots from CD and DBAN interface can be seen. DBAN detects two storage devices, HDD and the SD Card. My HDD IS 320GB but DBAN says 298GB. It erases the SD card but when i try to erase HDD, it gives following error. DBAN finished with non-fatal errors. *ERROR /dev/sdb (process crash) *ERROR /dev/sda (process crash)

  Read the article

• Good quality voice communication software over Internet for windows

  - by ORA600

  I regularly attend over-the-phone meetings, where is a polycom/polispan device on the other side. The quality of the sound is bad, even those whose English is a first language sometimes are struggling to realize what is being said on the other side. I understand this is because of too aggressive audio compression in the line. Does anyone know any good audio chat software which does not over-compress audio stream. The IP channel between two offices is wide enough. In other words, you should be able to listen to a music (not only a speech) from the remote side with good quality. So, Skype is too over-compressing as well. Does anyone know anything like that?

  Read the article

• One Way Sync of a Bucket With Local Directory

  - by user48651

  I have a local directory that I would like to synchronize with an S3 bucket. I have two specific requirements: If local file is the same as the remote, do not re-transfer it to the bucket. If some files or directories exist in the bucket but do not exist on local, delete them. Basically the bucket should mirror the local copy and not vice-versa. I looked into s3cmd sync command, but unfortunately requirement 2 is not fulfilled. If files exists in the bucket but not on local copy, they will be copied to the local instead of being deleted.

  Read the article

• Does dual-channel work only with an even number of RAM sticks?

  - by iconiK

  I have noticed that on the ASUS P5QL Pro motherboard the BIOS says "Dual Channel Asymmetric Mode" during POST. The motherboard has three 2GB Kingston ValueRAM 800 MHz DIMMs populated in the first 3 slots from the CPU socket. I have not run any benchmarks to verify that dual-channel is somehow being used, but I believed that dual-channel has to have an even number of sticks (and for triple channel, a multiple of 3). Another example is the Intel DX58SO motherboard; it has four DIMM slots, yet it's an LGA 1366 motherboard which does triple-channel. Apparently triple-channel still works with four DIMMs, instead of falling back to dual-channel. What does the BIOS' POST message mean in those case? Is dual-channel really used for the first two DIMMs, with the other one being an odd one in single-channel mode?

  Read the article

• usb device in dual mode on gentoo linux

  - by Idlecool

  i am having a flip flop usb modem which has two modes 1 usb mass storage mode: root@devbox:/media/F872F0FD72F0C184/Users/idlecool/Downloads# lsusb Bus 006 Device 003: ID 19d2:fff5 ONDA Communication S.p.A. 2 usbserial mode: root@devbox:/media/F872F0FD72F0C184/Users/idlecool/Downloads# lsusb Bus 006 Device 003: ID 19d2:fffe ONDA Communication S.p.A. by default whenever i plug the modem to the usb port.. the linux machine recognize it as a usb mass storage device.. how can i make it load as usbserial device i have been using a package usb_modeswitch in the past on ubuntu 10.04 but i cannt install the same package on gentoo live cd.. even udev is not installed on live cd.. how to change the product-id of the usb device on gentoo live disc without udev.

  Read the article

• Minimal Lunix distribution with sshd and apt

  - by Sergey Mikhanov

  When I signed up for my Debian Linux VPS hosting and first logged on and invoked ps, there was the only user process running: sshd. As I can see, this was minimal Linux with only two things installed and configured: sshd and apt (plus all dependencies, of course). I want to build (or use existing) similar Linux distro, any advice on how to build (or pick) one? Googling "minimum linux", or "linux with sshd only" usually brings up Debian's netinstall, which is not what I want. Thanks in advance.

  Read the article

• Linux says a kernel module has an unknown symbol, but another loaded module provides it.

  - by raldi

  I'm trying to install a driver for a USB DAQ box, which annoyingly, I have to compile myself. I believe I've succeeded -- I have two .ko files: -rw-r--r-- 1 root root 45271 2010-03-18 21:24 advdrv_core.ko -rw-r--r-- 1 root root 24312 2010-03-18 21:24 usb4761.ko I was able to run insmod on the first without incident, but when I try on the second, I get a flood of messages: kernel: [686782.106547] usb4761: no symbol version for adv_process_info_check_event kernel: [686782.106555] usb4761: Unknown symbol adv_process_info_check_event kernel: [686782.106691] usb4761: no symbol version for advdrv_unregister_driver kernel: [686782.106695] usb4761: Unknown symbol advdrv_unregister_driver However, advdrv_core.ko provides these symbols. My kernel sure seems to have them in memory: # cat /proc/kallsyms | grep advdrv_unregister_driver f8d88504 r __ksymtab_advdrv_unregister_driver [advdrv_core] f8d888d2 r __kstrtab_advdrv_unregister_driver [advdrv_core] f8d885a4 r __kcrctab_advdrv_unregister_driver [advdrv_core] 086eb8fb a __crc_advdrv_unregister_driver [advdrv_core] f8d86e90 t advdrv_unregister_driver [advdrv_core] Why does my insmod claim they're unknown symbols?

  Read the article

• HP DL380 G5 Predictive Drive Failure on a new drive

  - by CharlieJ

  Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

  Read the article

• how can I discover what keys are being sent when I press a mouse button?

  - by jcollum

  I'd like to map my Logitech MX Revolution keys in Visual Studio. More importantly, I'd like to do it without installing any software. Is this possible? I specifically want to map the two side buttons to View.NavigateBackward and View.NavigateForward. But I'm not sure what those keys are mapped to right now. I thought they were mapped to Ctrl-Tab and Shift-Ctrl-Tab, since they seem to behave that way in Notepad++, but that isn't working in VS. I'm on the work computer, which means 2 problems: I'm in Windows XP and installing software is frowned upon/monitored.

  Read the article

• Can I configure mod_proxy to use different parameters based on HTTP Method?

  - by Graham Lea

  I'm using mod_proxy as a failover proxy with two balance members. While mod_proxy marks dead nodes as dead, it still routes one request per minute to each dead node and, if it's still dead, will either return 503 to the client (if maxattempts=0) or retry on another node (if it's 0). The backends are serving a REST web service. Currently I have set maxattempts=0 because I don't want to retry POSTs and DELETEs. This means that when one node is dead, each minute a random client will receive a 503. Unfortunately, most of our clients are interpreting codes like 503 as "everything is dead" rather than "that didnt work but please try that again". In order to program some kind of automatic retry for safe requests at the proxy layer, I'd like to configure mod_proxy to use maxattempts=1 for GET and HEAD requests and maxattempts=0 for all other HTTP Methods. Is this possible? (And how? :)

  Read the article

< Previous Page | 758 759 760 761 762 763 764 765 766 767 768 769  | Next Page >