Search Results

Search found 5695 results on 228 pages for 'logoff scripts'.

Page 77/228 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

• NIC reordering on RHEL5/CentOS 5

  - by ewwhite

  I have an HP ProLiant DL360 G6 containing two onboard NICs as well as an HP NC375T (NetXen NX3031 chipset) 4-port PCIe card. The system was running with eth0 and eth1 belonging to the onboard NICs and eth2-eth5 on the NetXen card. I recently rebuilt the server and from the kickstart process onward, the NICs were reordered such that the onboard NICs became eth4 and eth5, while the NetXen card took over eth0-eth3. I've had some experiences in the past where I tied NICs to specific interfaces via changes in the ifcfg-ethX config files, but this is the first time I've ever seen an add-in card take over eth0 from the motherboard's interfaces. This impacted my kickstart scripts, so: 1). How can I ensure that the onboard NICs take precedence in the kickstart arrangement. 2). What is the most consistent way to maintain that ordering through repeated reboots, kernel changes (e.g. going from a RHEL mainline kernel to a RHEL MRG realtime kernel), etc. 3). What is the interaction between the /etc/modprobe.conf module/NIC definitions, the /etc/sysconfig/network-scripts/ifcfg-ethX and the /etc/modprobe.d/blacklist functions in this context?

  Read the article

• New tomcat install on OSX choking on startup.

  - by baudot

  I've completed a fresh install of Tomcat6 on an OS X box that didn't have it before. It's behaved a bit strangely in other ways, but the current hang-up is that it won't start at all. In response to running startup.sh, the catalina.out log collects this error: Exception in thread "main" java.lang.NoClassDefFoundError: org/apache/catalina/startup/Bootstrap Caused by: java.lang.ClassNotFoundException: org.apache.catalina.startup.Bootstrap at java.net.URLClassLoader$1.run(URLClassLoader.java:202) at java.security.AccessController.doPrivileged(Native Method) at java.net.URLClassLoader.findClass(URLClassLoader.java:190) at java.lang.ClassLoader.loadClass(ClassLoader.java:307) at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:301) at java.lang.ClassLoader.loadClass(ClassLoader.java:248) Other bits of strangeness noticed with this installation: the .sh scripts in the bin directory had no execute permission, and had to be manually chmodded. The log folder wasn't created, causing an earlier script crash. After I manually created the log folder, the startup script made it to this new error before failing. Running other scripts in the bin folder generates similar error messages involving NoClassDefFoundError. Bootstrap.java is indeed in the right place, though Bootstrap.class isn't in the same folder. For that matter, if any of the myriad class files for tomcat should have already been generated from their .java files, I haven't seen it.

  Read the article

• Security implications of adding www-data to /etc/sudoers to run php-cgi as a different user

  - by BMiner

  What I really want to do is allow the 'www-data' user to have the ability to launch php-cgi as another user. I just want to make sure that I fully understand the security implications. The server should support a shared hosting environment where various (possibly untrusted) users have chroot'ed FTP access to the server to store their HTML and PHP files. Then, since PHP scripts can be malicious and read/write others' files, I'd like to ensure that each users' PHP scripts run with the same user permissions for that user (instead of running as www-data). Long story short, I have added the following line to my /etc/sudoers file, and I wanted to run it past the community as a sanity check: www-data ALL = (%www-data) NOPASSWD: /usr/bin/php-cgi This line should only allow www-data to run a command like this (without a password prompt): sudo -u some_user /usr/bin/php-cgi ...where some_user is a user in the group www-data. What are the security implications of this? This should then allow me to modify my Lighttpd configuration like this: fastcgi.server += ( ".php" => (( "bin-path" => "sudo -u some_user /usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "4", "PHP_FCGI_MAX_REQUESTS" => "10000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) ) ...allowing me to spawn new FastCGI server instances for each user.

  Read the article

• Change the Powershell $profile directory

  - by Swoogan

  I would like to know how to change my the location my $profile variable points to. PS H:\> $profile H:\WindowsPowerShell\Microsoft.PowerShell_profile.ps1 H:\ is a network share, so when I create my profile file, and load powershell I get the following: Security Warning Run only scripts that you trust. While scripts from the Internet can be useful, this script can potentially harm your computer. Do you want to run H:\WindowsPowerShell\Microsoft.PowerShell_profile.ps1? [D] Do not run [R] Run once [S] Suspend [?] Help (default is "D"): According to Microsoft, the location of the $profile is determined by the %USERPROFILE% environment variable. This is not true: PS H:\> $env:userprofile C:\Users\username For example, I have an XP machine working how I want: PS H:\> $profile C:\Documents and Settings\username\My Documents\WindowsPowerShell\Microsoft.PowerShell_profile.ps1 PS H:\> $env:userprofile C:\Documents and Settings\username PS H:\> $env:homedrive H: PS H:\> $env:homepath \ Here's the same output from the Vista machine where the $profile points to the wrong place: PS H:\> $profile H:\WindowsPowerShell\Microsoft.PowerShell_profile.ps1 PS H:\> $env:userprofile C:\Users\username PS H:\> $env:homedrive H: PS H:\> $env:homepath \ Since $profile isn't actually determined by %USERPROFILE% how do I change it? Clearly anything that involves changing the homedrive or homepath is not the solution I'm looking for.

  Read the article

• Excel fails to open Python-generated CSV files

  - by johnjdc

  I have many Python scripts that output CSV files. It is occasionally convenient to open these files in Excel. After installing OS X Mavericks, Excel no longer opens these files properly: Excel doesn't parse the files and it duplicates the rows of the file until it runs out of memory. Specifically, when Excel attempts to open the file, a prompt appears that reads: "File not loaded completely." Example of code I'm using to generate the CSV files: import csv with open('csv_test.csv', 'wb') as f: writer = csv.writer(f) writer.writerow([1,2,3]) writer.writerow([4,5,6]) Even the simple file generated by the above code fails to load properly in Excel. However, if I open the CSV file in a text editor and copy/paste the text into Excel, parse it with text to columns, and then save as CSV from Excel, then I can reopen the CSV file in Excel without issue. Do I need to pass an additional parameter in my scripts to make Excel parse the CSV files the same way it used to? Or is there some setting I can change in OS X Mavericks or Excel? Thanks.

  Read the article

• How to encourage Windows administrators to pick up scripting?

  - by icelava

  When I worked as an administrator in my first job, I was frustrated that our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• Deploy our own software using Puppet?

  - by Ken

  (Apologies in advance for the stupidity in this question. I'm normally a programmer, not a sysadmin, but I've taken it upon myself to automate some things, and clean up some other things which are automated but not in the prettiest way. :-) I've been looking around at various tools for automation of software deployment to a bunch of servers, like cfengine, Puppet, and Chef. So far, Puppet looks the most appealing, but I've certainly not committed to anything yet. These tools all look like they can do a great job of keeping a bunch of servers up-to-date with prepackaged software. What I don't get is: how does one use a tool (like Puppet) to manage deployments of our own internal software? I think I'm at a loss because I've seen a thousand tutorials showing how to keep Apache ensure => latest (which is pretty cool), but nothing that quite corresponds to my use-case today, which is something more like: when a human being pushes The Button, pull branch A from the version-control repository B run command C to compile it copy the binaries D to servers E1 through E10 on each server, run command F to make all changes take effect Puppet sounds great, and I totally see the advantage of declarative, idempotent configuration over some shell scripts, but I've not seen any tutorials for "you want to update your shell scripts to Puppet (or Chef, or cfengine) so here's what you should do". Is there such a thing? Is it obvious to other people how to take the things provided in the Puppet docs and replicate the behavior I want? Am I just not getting it? What it's sounding like to me, so far, is that the human being (#1) would manually package the software (#2 and #3) external to Puppet, manually update the Puppet config, which would trigger Puppet to update the servers ... maybe? (I'm a little confused here, as I'm sure you can tell.) Thanks!

  Read the article

• How to encourage Windows administrators to pick up scripting

  - by icelava

  When i worked as an administrator in my first job, I was frustrated our administration processes with Windows servers were a series of point-and-clicks; we could never match the level of efficiency with the Unix servers which had a group of shell scripts to automate a lot of the work. I soon read about WSH and ADSI and wasted no time learning just how much automation I was able to achieve with scripting. There was a huge problem though - almost none of my Windows colleagues were really interested in learning scripting. They seemed happy with the manually mouse-clicking chores and were never excited at the prospect of using scripts to do the work on their behalf. I struggled to convince them to pick up scripting skills despite the evident increases in efficiency. I left that job in pursuit of a full-time software development career thereafter. Almost a decade on working in various environments and different customers, I still encounter Windows administrators mainly possessing this general "mood" where they would avoid scripting as much as possible. Despite the increasing level of accessibility Windows server technologies are opening up for scripting and automation. I am almost certain the majority of administrators are administrators precisely because they absolutely hate performing any kind of programming duties. What are some means to encourage and motivate administrators that scripting can really help them in the long run?

  Read the article

• mod_fcgi produces random 500 Errors

  - by DmitrySemenov

  php 5.4.7 via mod_fcgi when I run the site sometimes it works, sometimes it crashed with 500 Internal Error, this is what I see in error.log everytime I run the script [Mon Sep 24 18:50:43 2012] [warn] [client 68.231.194.198] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Mon Sep 24 18:50:43 2012] [error] [client 68.231.194.198] Premature end of script headers: api.php any ideas? vhost config: <VirtualHost :80> ServerAdmin [email protected] DocumentRoot "/home/www/sites/test.com/html/development" ServerName test.com ServerAlias www.test.com ErrorLog "/home/www/sites/test.com/logs/error_log" CustomLog "/home/www/sites/test.com/logs/access_log" common <IfModule mod_fcgid.c> <Directory /home/www/sites/test.com/html/development> Options +ExecCGI AllowOverride All AddHandler fcgid-script .php FCGIWrapper /home/www/php-fcgi-scripts/php-fcgi-starter .php Order allow,deny Allow from all </Directory> FcgidMaxRequestLen 1073741824 </VirtualHost> fcgi.d conf LoadModule fcgid_module modules/mod_fcgid.so # Use FastCGI to process .fcg .fcgi & .fpl scripts AddHandler fcgid-script fcg fcgi fpl # Sane place to put sockets and shared memory file FcgidIPCDir /var/run/mod_fcgid FcgidProcessTableFile /var/run/mod_fcgid/fcgid_shm IdleTimeout 300 BusyTimeout 300 ProcessLifeTime 7200 IPCConnectTimeout 300 IPCCommTimeout 7200 PHP_Fix_Pathinfo_Enable 1 php-fcgi-starter.php #!/bin/sh PHP_CGI=/usr/local/php547/bin/php-cgi PHP_INI=/etc/php547-fastcgi.ini export PHP_FCGI_TIMEOUT=1200 #export PHP_FCGI_CHILDREN=6 export PHP_FCGI_MAX_REQUESTS=1000 exec $PHP_CGI -c $PHP_INI

  Read the article

• How do I enable additional debugging output from Ansible and Vagrant?

  - by Brian Lyttle

  I'm investigating Ansible for server and application provisioning. My application is currently provisioned with shell scripts in Vagrant. Rather than rewrite my scripts I've taken a sample and attempted to deploy it. It appears to deploy fine, but I've seeing a failure message after what looks like a series of successful steps: » vagrant provision ~/vm/blvagrant 1 ? [default] Running provisioner: ansible... PLAY [web-servers] ************************************************************ GATHERING FACTS *************************************************************** ok: [192.168.9.149] TASK: [install python-software-properties] ************************************ ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [add nginx ppa if it ubuntu 10.04 and up] ******************************* ok: [192.168.9.149] => {"changed": false, "item": "", "repo": "ppa:nginx/stable", "state": "present"} TASK: [update apt repo] ******************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [install nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": ""} TASK: [copy fixed init for nginx] ********************************************* ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0755", "owner": "root", "path": "/etc/init.d/nginx", "size": 2321, "state": "file", "uid": 0} TASK: [service nginx] ********************************************************* ok: [192.168.9.149] => {"changed": false, "item": "", "name": "nginx", "state": "started"} TASK: [write nginx.conf] ****************************************************** ok: [192.168.9.149] => {"changed": false, "gid": 0, "group": "root", "item": "", "mode": "0644", "owner": "root", "path": "/etc/nginx/nginx.conf", "size": 1067, "state": "file", "uid": 0} PLAY RECAP ******************************************************************** 192.168.9.149 : ok=8 changed=0 unreachable=0 failed=0 Ansible failed to complete successfully. Any error output should be visible above. Please fix these errors and try again. How do I go about getting additional debug information? I've already added ansible.verbose = true to my vagrant config which results in the dictionaries being displayed within the output above.

  Read the article

• Changing a set-cookie header using mod_rewrite/mod_proxy

  - by olrehm

  I have a bunch of cgi scripts, which are served using HTTPS. They can only be reached on the intranet, not from the outside. They set a cookie with the attribute 'Secure', so that it can only be send via HTTPS. There is also a reverse proxy to one of these scripts, unfortunately using plain HTTP. When a response comes in from my cgi-script with a secure cookie, it is not being passed on via HTTP (after all, that is what that attribute is for). I need however, an exception to this rule. Is it possible to use mod_rewrite/mod_proxy or something similar, to change the set-cookie header in the response coming from my cgi script and remove the Secure, such that the cookie can be passed back to the user using the unsafe HTTP connection? I understand that this defeats the purpose of the Secure in the first place, but I need this as a temporary work around. I have searched the web and found how to add a set-cookie header using mod_rewrite, and I have also found how to retrieve the value of a cookie coming from the client in a cookie header. What I have not yet found is how to extract the set-cookie header received in the response of a script I am proxying for. Is that possible? How would I do that? Ole

  Read the article

• Patch management on multiple systems

  - by Pierre

  I'm in charge of auditing the security configuration of an important farm of Unix servers. So far, I came up with a way to assess the basic configuration but not the installed updates. The very problem here is that I just can't trust the package management tools on those machine. Indeed some of them did not sync with the repository for a long time (So I can't do a "yum check-updates" on Redhat for example). Some of those servers are not even connected to the internet and use an company repository. Another problem is that I have multiple target systems: AIX, Debian, Centos/Redhat, etc... So the version could be different (AIX) and the tools available will be different. And, last but not least, I can't install anything on the target system. So I need to use a script to retrieve the information and either: process it directly or save the information to be able to process it later on a server (Which may happen to run a different distribution than the one on which the information have been retrieved). The best ideas I could come up with were: either retrieve the list of installed packages on the machine (dpkg -l for example on debian) and process it on a dedicated server (Directly parsing the "Packages" file of debian repositories). Still, the problem remains the same for AIX and Redhat... or use Nessus' scripts to assess vulnerability on the installed packages, but I find this a bit dirty. Does anyone know any better/efficient way of doing this ? P.S: I already took time to review some answers to similar problems. Unfortunately Chef, puppet, ... don't meet the requirements I have to meet. Edit: Long story short. I need to have the list of missing updates on a Unix system just like MBSA on Windows. I'm not authorized to install anything on this system as it's not mine. All I have are scripts languages. Thanks.

  Read the article

• Is it possible to use rsync over sftp (without an ssh shell) ?

  - by Tom Feiner

  Rsync over ssh, works great every time. However, trying to rsync to a host which allows only sftp logins, but not ssh logins, provides the following error: rsync -av /source ssh user@remotehost:/target/ protocol version mismatch -- is your shell clean? (see the rsync man page for an explanation) rsync error: protocol incompatibility (code 2) at compat.c(171) [sender=3.0.6] Here's the relevant section from the rsync man page: This message is usually caused by your startup scripts or remote shell facility producing unwanted garbage on the stream that rsync is using for its transport. The way to diagnose this problem is to run your remote shell like this: ssh remotehost /bin/true > out.dat then look at out.dat. If everything is working correctly then out.dat should be a zero length file. If you are getting the above error from rsync then you will probably find that out.dat contains some text or data. Look at the contents and try to work out what is producing it. The most com- mon cause is incorrectly configured shell startup scripts (such as .cshrc or .profile) that contain output statements for non-interactive logins. Trying this on my system produced the following in out.dat: ssh-dummy-shell: Command not allowed. As I thought, the host is not allowing ssh logins. The following link shows that it is possible to accomplish this task using fuse with sshfs - however it is extremely slow, and not fit for production use. Is there any chance of getting rsync sftp to work?

  Read the article

• Reset rc.d so software starts at boot again

  - by natli

  I ran the following 2 commands on my VPS box and now it boots without starting any software at all. According to rcconf it's still supposed to start my chosen software (ssh etc.) but it doesn't. update-rc.d vz defaults update-rc.d vzeventd defaults I already tried removing them again with update-rc.d -f vz remove update-rc.d -f vzeventd remove But that didnt't change anything. /etc/rc.local also still correctly lists some scripts I want to run at start-up, but they don't seem to be called either. I expect the top 2 commands to be responsible, but here's everything I did: mkdir /var/openvz-dl cd /var/openvz-dl wget http://download.openvz.org/kernel/branches/rhel6-2.6.32/042stab062.2/vzkernel-2.6.32-042stab062.2.x86_64.rpm wget http://download.openvz.org/kernel/branches/rhel6-2.6.32/042stab062.2/vzkernel-devel-2.6.32-042stab062.2.x86_64.rpm wget http://download.openvz.org/utils/vzctl/4.0/vzctl-4.0-1.x86_64.rpm wget http://download.openvz.org/utils/vzctl/4.0/vzctl-core-4.0-1.x86_64.rpm wget http://download.openvz.org/utils/ploop/1.5/ploop-1.5-1.x86_64.rpm wget http://download.openvz.org/utils/ploop/1.5/ploop-lib-1.5-1.x86_64.rpm wget http://download.openvz.org/utils/vzquota/3.1/vzquota-3.1-1.x86_64.rpm apt-get install fakeroot alien fakeroot alien --to-deb --scripts --keep-version vz*.rpm ploop*.rpm dpkg -i vz*.deb ploop*.deb --force-overwrite update-rc.d vz defaults update-rc.d vzeventd defaults reboot A huge part of that failed because I was running it on an OpenVZ VPS which has a shared kernel that can't be altered, so I also had to fix the dpkg like so (it was moaning about wanting to install vzkernel with a package not being found); rm /var/lib/dpkg/info/vzkernel* dpkg-reconfigure vzkernel --force dpkg --purge --force-all vzkernel But that didn't fix the boot issue either. How do I make my software start at boot again?

  Read the article

• Apache using 100% CPU, once again

  - by CBenni

  Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

  Read the article

• Multiple copies off the same printer on Windows 7 from PrintUIEntry

  - by Kev

  I currently have a number of bat files which work perfectly fine on Windows XP which install the same printer multiple times with a number of finisher options set - e.g. after running the bat file below I would end up with four printers in the printer drop down called Sharp Kits Printer - A4 Single Sided Sharp Kits Printer - A4 Single Sided Stapled Sharp Kits Printer - A4 Duplex Stapled Sharp Kits Printer - A4 Duplex which all have there options configured in the relevant way. I have amended on Windows 7 to point to correct INF file and printer name in the INF files - a single printer installs fine. However when I run the complete batch file only the first printer in it is installed - occassionally the later ones flash up in the GUI but then vanish when you press F5 and are still missing after a reboot. SET QUEUENAME=http://192.168.7.123:631/printers/Sharp700 SET PPD=J:\DRIVERS\Printers\MX700-Win7-64\SJ1JWENG.INF SET PPDENTRYNAME=SHARP MX-M700U PPD J: cd "\DRIVERS\Printers\MX700-Win7-64" SET NICENAME="Sharp Kits Printer - A4 Single Sided" SET PREFS="J:\SCRIPTS\Printers-Win7-64bit\Sharp_SINGLE_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... SET NICENAME="Sharp Kits Printer - A4 Duplex" SET PREFS="J:\SCRIPTS\Printers\Sharp_DUPLEX_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... I have tried adding the "/u" paramater to the end, I have changed the "/n" paramater to be different (e.g. n1, n2,n3 etc) - both of these result in the same. I have also tried to change the port (/r) to have "_1" (etc) on the end like the GUI would but this errors as the port doesn't exist. Is it possible to do this on Windows 7, and if so how?

  Read the article

• Need help trying to allow my remote PowerShell script to run on my Windows 2008 r2 Server

  - by Pure.Krome

  I've got a Windows 2008 r2 server with Sql Server 2008 r2 installed. I've got a Sql Server Agent which tries to run a Powershell job, but fails :- Message Executed as user: FooServer\SqlServerUser. A job step received an error at line 1 in a PowerShell script. The corresponding line is '& '\\polanski\Backups\Database\7ZipFooDatabases.ps1'' Correct the script and reschedule the job. The error information returned by PowerShell is: 'File \\polanski\Backups\Database\7ZipFooDatabases.ps1 cannot be loaded. The file \\polanski\Backups\Database\7ZipFooDatabases.ps1 is not digitally signed. The script will not execute on the system. Please see "get-help about_signing" for more details.. '. Process Exit Code -1. The step failed. Ok. So i run Powershell on that server then set the execution policy to unrestricted. To check .. PS C:\Users\theUser> Get-ExecutionPolicy Unrestricted PS C:\Users\theUser> Kewl :) but it still doesn't work :( Ok ... what happens when i try to run the powershell from the command line.... PS C:\Users\justin.adler . '\polanski\Backups\Database\7ZipMotorshoutDatabases.ps1' Security Warning Run only scripts that you trust. While scripts from the Internet can be useful, this script can potentially harm your computer. Do you want to run \\polanski\Backups\Database\7ZipFooDatabases.ps1? [D] Do not run [R] Run once [S] Suspend [?] Help (default is "D"): er..... didn't I already tell the server that ANY file can be ran? Notice the file is located at... \\polanski\Backups\Database\ So can someone make any suggestions?

  Read the article

• What user information is exposed via a browser?

  - by ipso

  Is there a function or website that can collect and display ALL of the user information that can be obtained via a browser? Background: This of course does not account for the significant cross-reference abilities of large corporations to collate multiple sources and signals from users across various properties, but it's a first step. Ghostery is just a great idea; to show people all of the surreptitious scripts that run on any given website. But what information is available – what is the total set of values stored – that those scripts can collect from? If you login to a search engine and stay logged in but leave their tab, is that company still collecting your webpage viewing and activity from other tabs? Can past or future inputs to pages be captured – say comments on another website? What types of activities are stored as variables in the browser app that can be collected? This is surely a highly complex question, given to countless user scenarios – but my whole point is to be able to cut through all that – and just show the total set of data available at any given point in time. Then you can A/B test and see what is available with in a fresh session with one tab open vs. the same webpage but with 12 tabs open, and a full day of history to boot. (Latest Firefox & Chrome – on Win7, Win8 or Mint13 – although I'd like to think that won't make too much of a difference. Make assumptions. Simple is better.)

  Read the article

• powershell vs GPO for installation, configuration, maintenance

  - by user52874

  My question is about using powershell scripts to install, configure, update and maintain Windows 7 Pro/Ent workstations in a 2008R2 domain, versus using GPO/ADMX/msi. Here's the situation: Because of a comedy of cumulative corporate bumpfuggery we suddenly found ourselves having to design, configure and deploy a full Windows Server 2008R2 and Windows 7 Pro/Enterprise on very short notice and delivery schedule. Of course, I'm not a windows expert by any means, and we're so understaffed that our buzzword bingo includes 'automate' and 'one-button' and 'it needs to Just Work'. (FWIW, I started with DEC, then on to solaris and cisco, then linux of various flavors with a smattering of BSD nowadays. I use Windows for email and to fill out forms). So we decided to bring in a contractor to do this for us. and they met the deadline. The system is up and mostly usable, and this is good. We would not have been able to do this. But it's the 'mostly' part that is proving to be the PIMA now, and I'm having to learn Microsoft stuff anyway until/if we can get a new contract with these guys for ongoing operations. Here's my question. The contractor used powershell almost exclusively for deployment, configuration and updating. My intensive reading over the last week leads me to think that the generally accepted practices for deployment, configuration and updating microsoft stuff uses elements of GPOs and ADMX templates, along with maybe some third party stuff like PolicyPak. Are there solid reasons that I've not found yet that powershell scripts would be preferred over the GPO methods? I'm going to discuss this with the contractor lead when he gets back from his vacation, and he'll be straight with me (nor do I think they set us up). But I can also see this might be a religious issue, so I would still like some background on this. Thoughts? or weblinks? Thanks!

  Read the article

• Synchronizing the SamAccountName Property using Windows Azure Active Directory Sync Tool

  - by pk.

  Using this official documentation as a guide, I would expect the SamAccountName property to sync from my on-premise AD to Office 365. I think that it used to do exactly that, but now it seems that it doesn't so much sync the attribute as it does create an entirely new, unlinked value and store it in Office 365. This has caused some minor issues for me (broken scripts, annoying permissions management, etc.) and may be part of a more major issue regarding ADFS authentication. On-Premise PS C:\Windows\system32> Get-ADUser jdoe -Properties SamAccountName | fl SamAccountName SamAccountName : jdoe Office 365 Sync'ed Objects PS C:\Windows\system32> Get-Mailbox jdoe | fl SamAccountName SamAccountName : $1A7H20-K1LCOJFFBHGS I understand how to work around this issue in my scripts -- there exists the ImmutableId property which can be mapped back to the on-premise GUID. As far as the issue I'm having with ADFS, I'm less certain how to proceed and if this is causing my issues. At this point I really would just like some verification that I'm not crazy and that this used to be sync'ed at some point in the past and that Office 365 broke it relatively recently. I also think that MS documentation should perhaps be updated to exclude SamAccountName from the list of synchronized properties on the page I linked.

  Read the article

• Expire Files In A Folder: Delete Files After x Days

  - by Brett G

  I'm looking to make a "Drop Folder" in a windows shared drive that is accessible to everyone. I'd like files to be deleted automagically if they sit in the folder for more than X days. However, it seems like all methods I've found to do this, use the last modified date, last access time, or creation date of a file. I'm trying to make this a folder that a user can drop files in to share with somebody. If someone copies or moves files into here, I'd like the clock to start ticking at this point. However, the last modified date and creation date of a file will not be updated unless someone actually modifies the file. The last access time is updated too frequently... it seems that just opening a directory in windows explorer will update the last access time. Anyone know of a solution to this? I'm thinking that cataloging the hash of files on a daily basis and then expiring files based on hashes older than a certain date might be a solution.... but taking hashes of files can be time consuming. Any ideas would be greatly appreciated! Note: I've already looked at quite a lot of answers on here... looked into File Server Resource Monitor, powershell scripts, batch scripts, etc. They still use the last access time, last modified time or creation time... which, as described, do not fit the above needs.

  Read the article

• File upload folder permission fastCGI - How to make it writeable?

  - by user6595

  I am using centos 5.7 with cPanel WHM running fastcgi/suEXEC I am trying to make a particular folder writable to allow a script to upload files but seem to be having problems. The folder (and all recursive folders) I want to be writable is: /home/mydomain/public_html/uploads And I want only scripts run by the user "songbanc" to be able to write to this directory. I have tried the following: chown -R songbanc /home/mydomain/public_html/uploads chmod -R 755 /home/mydomain/public_html/uploads But it still doesn't seem to work. The script will only upload files if I set the permissions manually via FTP client to 777. I assume I am misunderstanding how to set permission for users with fastcgi and hopefully someone can help me. Thanks in advance EDIT: Running getfacl on one of the scripts or folders gives the following: # file: home/mydomain/public_html/ripples/1.jpg # owner: songbanc # group: songbanc So it appears that the owner is correct? I'm now totally confused! EDIT 2: The plot thickens... lsattr and chattr are returning Inappropriate ioctl for device While reading flags on...

  Read the article

• Grub Autostart with timeout

  - by BetaRide

  On Ubuntu 10.4 LTS I want Grub to start the default OS after 5 Seconds. I'd like to see the output of the startup scripts. Currently grub wait forever until I hit return and the output of the startup scripts isn't visible. Can someone tell me how I have to configure /etc/default/grub or any other setups? I tried to play with GRUB_TIMEOUT and GRUB_DEFAULT and did a sudo update-grub afterwards, but nothing changed. Any ideas? # If you change this file, run 'update-grub' afterwards to update # /boot/grub/grub.cfg. GRUB_DEFAULT=0 GRUB_HIDDEN_TIMEOUT=5 #GRUB_HIDDEN_TIMEOUT_QUIET=true GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" GRUB_CMDLINE_LINUX="" GRUB_SAVEDEFAULT=true # Uncomment to disable graphical terminal (grub-pc only) #GRUB_TERMINAL=console # The resolution used on graphical terminal # note that you can use only modes which your graphic card supports via VBE # you can see them in real GRUB with the command `vbeinfo' #GRUB_GFXMODE=640x480 # Uncomment if you don't want GRUB to pass "root=UUID=xxx" parameter to Linux # GRUB_DISABLE_LINUX_UUID=true # Uncomment to disable generation of recovery mode menu entries #GRUB_DISABLE_LINUX_RECOVERY="true" # Uncomment to get a beep at grub start #GRUB_INIT_TUNE="480 440 1"

  Read the article

• CentOS: AJAX/jQuery not working

  - by Australiya

  In a nutshell, I have an unmanaged VPS. At one time, it had Ubuntu 10.10 server on it, then I reinstalled it with CentOS 6 and updated it to CentOS 6.2. Now, the problem is, the AJAX/jQuery shoutbox has ceased working (I assume it uses one of the two to inject itself into a div and then refresh when new messages are posted, I'm not sure, I didn't write these), and the plug-board script now shows me a lime green blank page. No changes to the source codes have been made, and they are in the location they expect themselves to be. I have Apache2, MySQL 5, PHP 5, and I did install the php-xml libraries. What am I missing? It's gotta be server side because the scripts themselves are fine, if I move them to a different server they work just fine. I'm not getting any errors related to this in the error_log file. Thanks in advance! Edit: If you want, you can look at the plugboard at kazeshini.net/plugboard and there's an installation of the chatbox at silverlotus.kazeshini.net/yshout/example, I know nothing about scripts and debugging so better someone else looks at it than someone that doesn't know what they're looking for.

  Read the article

• How can I find which logon script is being run?

  - by user2517266

  I'm having an issue with network drives. Suddenly some computers and users aren't getting their mapped network drives from the logon script. I am NOT a domain admin, I don't have permission to login to the domain controller. And I know very little about Active Directory. The issue seems random, some users this day, different users tomorrow. Some computers run fine and some won't map no matter who logs in. They are mixed OS's XP (SP3), Vista, and 7. I was looking at the domain in windows explorer and I have found the batch file(s) that maps the drives in several locations, how do I know which one is actually being ran? The .bat file is located in \DOMAIN\NETLOGON\script.bat and \DOMAIN\SYSVOL\DOMAIN\scripts\script.bat and \DOMAIN\SYSVOL\DOMAIN\policies\GUID(Right? It's a crazy string)\User\Scripts\Logon\script.bat So, how can I figure out which one is actually being ran per computer or user? Cause they are all slightly different from each other and one of them doesn't map properly. Do all the files in NETLOGON get ran? Cause there are 15+ files in there. Or is it specified in Group Policy which one(s) get ran? EDIT: I am able to access a program called Active Directory Users and Computers, but the properties tab for any user is blank for the logon script.

  Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >