Search Results

Search found 2798 results on 112 pages for 'pull'.

Page 77/112 | < Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• Broad Band LAN connection through existing 6 wire phone line ( no phone connected )

  - by Paul Taylor

  I have an (up to but never achieved ) 10 mb broadband signal coming into my house along the telephone line. The modem then connects the broadband signal via a LAN connection and Wi-Fi signal to my computers and iPad. My workshop desk is 54 yards (approx. 50m) downhill from the modem (part of a separate building) – too far to give a good direct signal. The inside corner of the workshop (by a window) receives a weak signal. I have a disconnected telephone cable consisting of 6 wires going from the house to the workshop. The telephone is no longer used in the workshop - we use our mobile number for business calls. A broad band signal using the cable would not have to share with a phone. What would be the most economic price/efficient way to get the broadband signal to the workshop? I am writing in hope that since the telephone didn't need the six wires, an Ethernet connection might be similar and not need all the eight wires for a LAN connection. In theory could use the telephone wire to pull an Ethernet cable trough the underground pipe but I doubt if the cable would survive the strain. The broad band connection in the workshop does not have to have network facility. My skill level is high enough to do house wiring, plumbing and gas fitting; so given any sound advice and a wiring diagram or instructions I can probably work out the rest myself.

  Read the article

• Barriers to IPv6 deployment: addressing

  - by sysadmin1138

  There are several things that are keeping IPv6 deployment from being a topic of active discussion here at my work. There are the usual technical issues, but one non-technical one appears to be a major stumbling block on the path to actually getting a deployment project going. Addresses, memorizing of. Specifically, IPv4 addresses are comprehensible, and IPv6 addresses just look like a big long string of hex. The human mind has real trouble memorizing lists of more than 7-8 items, and an IPv4 address (192.168.231.148) has four items in it which makes it easy for us to memorize. A fully populated IPv6 address has not only 8 sections, but each section has 4 hex digits in it. IPv6 addresses were not designed for memorization. To the technician who knows that the DNS server is at 192.168.42.42 (or more likely "42.42", since the company prefix is likely memorized), the idea of memorizing an IPv6 address fills them with dread. Which in turn makes them much less enthusiastic about participating in an IPv6 deployment project. Because of how our network works we're not fully dynamic in terms of v4 addressing. We have several to many subnets that are entirely statically assigned for a variety of reasons, chief among them being that the overhead of static DHCP assignments is perceived as being too great. Also, some devices still aren't smart enough to pull DNS addresses out of DHCP while also having a static assignment, and therefore require manually configured DNS settings. Therefore, some v6 address memorization will have to be done. We're not under any mandate to get v6 out the door, so we don't have pressure from the top. However, it is time to start prepping our infrastructure to handle IPv6 even if we don't convert wholesale. For those of you who have been in IPv6-land for a while, what short-cut methods do you use to discuss or keep track of subnets and specific/critical IP addresses? If I can help reduce some of the dread surrounding IPv6 we might get the project going.

  Read the article

• Google bots are severely affecting site performance

  - by Lynn

  I have an aggregate site on a linux server that pulls in feeds from a universe of about 2,000 blogs. It's in Wordpress 3.4.2 and I have a cron job that is staggered to run five times an hour on another server to pull in the stories and then publish them to the front page of this site. This is so I didn't put too much pressure all on one server. However, the Google bots, which visit a few times every hour bring the server to its knees in the morning and evenings when there is an increase in traffic on the site. The bots have something like 30,000 links to follow at this point. How do I throttle the bots to simply grab the new stories off the front page and stop there? EDIT- Details of my server configuration: The way we have this set up is the server that handles all the publishing is an unmanaged instance via AWS. It mounts the NFS server and connects to the RDS to update content, etc. You get to this publishing instance via a plugin that detects the wp-admin link and then redirects you into there. The front end app server also mounts the NFS and requests data from the RDS. It is the only one that has the WP Super Cache on it.... The OS is Ubuntu on the App server and the NFS runs CentOs. The front end is Nginx and the publishing server is Apache.

  Read the article

• Clustered MSDTC

  - by niel

  Hi I'm setting up a SQL cluster (SQL 2008), Windows 2008 R2. I enable the network access on local dtc and then create a DTC resource in my cluster . the problem is that when i start up the resource it does nto pull through my settings to enable network access. the log shows this: MSDTC started with the following settings: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 0, Trasaction Manager Communication: Allow Inbound Transactions = 0, Allow Outbound Transactions = 0, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 0, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = Mutual Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 where when i restart the local dtc service it says this: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 1, Trasaction Manager Communication: Allow Inbound Transactions = 1, Allow Outbound Transactions = 1, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 1, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = No Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 settings on both nodes in teh cluster is the same. I have reinstalled and restarted to many times to mention. Any ideas ?

  Read the article

• Deploy our own software using Puppet?

  - by Ken

  (Apologies in advance for the stupidity in this question. I'm normally a programmer, not a sysadmin, but I've taken it upon myself to automate some things, and clean up some other things which are automated but not in the prettiest way. :-) I've been looking around at various tools for automation of software deployment to a bunch of servers, like cfengine, Puppet, and Chef. So far, Puppet looks the most appealing, but I've certainly not committed to anything yet. These tools all look like they can do a great job of keeping a bunch of servers up-to-date with prepackaged software. What I don't get is: how does one use a tool (like Puppet) to manage deployments of our own internal software? I think I'm at a loss because I've seen a thousand tutorials showing how to keep Apache ensure => latest (which is pretty cool), but nothing that quite corresponds to my use-case today, which is something more like: when a human being pushes The Button, pull branch A from the version-control repository B run command C to compile it copy the binaries D to servers E1 through E10 on each server, run command F to make all changes take effect Puppet sounds great, and I totally see the advantage of declarative, idempotent configuration over some shell scripts, but I've not seen any tutorials for "you want to update your shell scripts to Puppet (or Chef, or cfengine) so here's what you should do". Is there such a thing? Is it obvious to other people how to take the things provided in the Puppet docs and replicate the behavior I want? Am I just not getting it? What it's sounding like to me, so far, is that the human being (#1) would manually package the software (#2 and #3) external to Puppet, manually update the Puppet config, which would trigger Puppet to update the servers ... maybe? (I'm a little confused here, as I'm sure you can tell.) Thanks!

  Read the article

• Upgrade SQLServer 2008 hardware

  - by John

  Forgive me if I'm not able to be totally clear here. It is not intentional, I'm a senior level developer in a very small company having to act like a manager at the moment. Anyway, the story is that we have 2 older dell servers with SQL Server 2008 Standard in a "cluster". I put that in quotes because I'm still not 100% clear what that means. We have 2 brand new blade servers and want to move the existing databases to the new hardware. Ok, so here is the gotcha. We need to do this with little or no down time. I'm being told that we can evict the passive node, then pull in one of the new servers. But I'm also being told that this is a dangerous step because something could go wrong that would cause the cluster to fail and then we would be left with nothing because the active server would not be able to come back up. Does anyone have any thoughts on how to handle this? I'm being told that the only way to ensure success is to have at least a day of down time where we bring up a new cluster on the new hardware and then migrate the databases 1 by 1.

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• Windows 7 scheduled task returns 0x2

  - by demmith

  I have identical scheduled tasks running in Windows XP Pro and Windows 7. The XP Pro one runs fine, the Windows 7 one always returns 0x2 (which means, "The system cannot find the file specified"; however, executing from the command line is no problem) in the Last Run Result column of the Task Scheduler UI. The scheduled task executes a .bat file daily. The .bat file contains a call to execute a Perl script. As I stated in the previous paragraph, it executes under XP without any trouble but under Windows 7, no dice. The task under Windows 7 is set to "run whether the user is logged on or not." In this case it is me, I am the only user of the system. It is also set to "Run with highest privileges." And it is not hidden. The .bat file executes perfectly well from the command line - it calls the Perl script as expected and the Perl script does its thing. I have searched far and wide looking for an appropriate answer to this issue. So far I have found nothing. What the devil is going on with this Win7 scheduled task? I am ready to pull my hair out.

  Read the article

• College network - can I point non-domain student computers to our SUS server?

  - by Joel Coel

  Since I started here 3 months ago, one of the things that's really bothered me about the way this network is setup is something that shows up on the daily bandwidth consumption report. I get a list of top-visited sites by hits and by size, and invariably the top site (to the point that it's bigger than all the other top sites combined) is au.download.windowsupdate.com. We're pulling in ~30GB/day in windows updates. This is every day, not just after a patch Tuesday. After a patch day, it jumps closer to 40GB for a couple days. The key here is that almost none if it is by machines that I'm responsible for. My machines are for the most part fully patched, and when they're not they'll pull from a SUS server, so new updates are downloaded only once. It used to be closer to 50GB/day because most of the machines in our computer labs use DeepFreeze and weren't applying updates correctly, but that's fixed now. So the problem is definitely student-owned machines in the dorms, some of which are re-downloading the same updates in background each day, over and over. I'd love to have these machines start pulling from our SUS server. Then, if they don't ever actually install them at least they're not leeching bandwidth from our public internet connection. Any ideas on how to resolve the situation?

  Read the article

• TCPDump and IPTables DROP by string

  - by Tiffany Walker

  by using tcpdump -nlASX -s 0 -vvv port 80 I get something like: 14:58:55.121160 IP (tos 0x0, ttl 64, id 49764, offset 0, flags [DF], proto TCP (6), length 1480) 206.72.206.58.http > 2.187.196.7.4624: Flags [.], cksum 0x6900 (incorrect -> 0xcd18), seq 1672149449:1672150889, ack 4202197968, win 15340, length 1440 0x0000: 4500 05c8 c264 4000 4006 0f86 ce48 ce3a E....d@[email protected].: 0x0010: 02bb c407 0050 1210 63aa f9c9 fa78 73d0 .....P..c....xs. 0x0020: 5010 3bec 6900 0000 0f29 95cc fac4 2854 P.;.i....)....(T 0x0030: c0e7 3384 e89a 74fa 8d8c a069 f93f fc40 ..3...t....i.?.@ 0x0040: 1561 af61 1cf3 0d9c 3460 aa23 0b54 aac0 .a.a....4`.#.T.. 0x0050: 5090 ced1 b7bf 8857 c476 e1c0 8814 81ed P......W.v...... 0x0060: 9e85 87e8 d693 b637 bd3a 56ef c5fa 77e8 .......7.:V...w. 0x0070: 3035 743a 283e 89c7 ced8 c7c1 cff9 6ca3 05t:(>........l. 0x0080: 5f3f 0162 ebf1 419e c410 7180 7cd0 29e1 _?.b..A...q.|.). 0x0090: fec9 c708 0f01 9b2f a96b 20fe b95a 31cf ......./.k...Z1. 0x00a0: 8166 3612 bac9 4e8d 7087 4974 0063 1270 .f6...N.p.It.c.p What do I pull to use IPTables to block via string. Or is there a better way to block attacks that have something in common? Question is: Can I pick any piece from that IP packet and call it a string? iptables -A INPUT -m string --alog bm --string attack_string -j DROP In other words: In some cases I can ban with TTL=xxx and use that should an attack have the same TTL. Sure it will block some legit packets but if it means keeping the box up it works till the attack goes away but I would like to LEARN how to FIND other common things in a packet to block with IPTables

  Read the article

• IIS not responding with SSL Server Hello

  - by Damien_The_Unbeliever

  I'm having difficulty getting a particular IIS machine to "do" SSL. This is a test environment (one of many) which we've set up "the same" as we have many times previously, but it just doesn't seem to be working. The server is Windows Server 2003 (Version 5.2 (Build 3790.srv03_sp2_gdr.100216-1301 : Service Pack 2)) IIS is hosting 4 sites (including the default site), but only one site is configured for SSL. We're using the same SSL certificate we use on all of our other servers (it's a wildcard cert). (Don't think this is relevant, but including anyway) We've configured the site to require SSL, it has a subdirectory that doesn't require SSL but has an asp page that redirects into SSL. The 403;4 error page for the site is hooked up to this asp page (this is how we do our non-HTTPS into HTTPS transition). Using Microsoft Network Monitor (3.3), I've just run a session against a server where SSL is working. It can pull apart the SSL exchange as the following messages: SSL: Client Hello SSL: Server Hello. Certificate. Server Hello Done SSL: Client Key Exchange. Change Cipher Spec. Encrypted Handshake Message. SSL: Change Cipher Spec. Encrypted Handshake Message However, on our problem server, I only see: SSL: Client Hello. The next packet from the server (from port 443, so it's listening and responding there) contains only 60 bytes, and just seems to have the Tcp headers and not much else (but I'm by no means an expert at deciphering these things). So, where do I look next? Or what additional information do I need to add to this question, and where do I find it?

  Read the article

• Fast extraction of a time range from syslog logfile?

  - by mike

  I've got a logfile in the standard syslog format. It looks like this, except with hundreds of lines per second: Jan 11 07:48:46 blahblahblah... Jan 11 07:49:00 blahblahblah... Jan 11 07:50:13 blahblahblah... Jan 11 07:51:22 blahblahblah... Jan 11 07:58:04 blahblahblah... It doesn't roll at exactly midnight, but it'll never have more than two days in it. I often have to extract a timeslice from this file. I'd like to write a general-purpose script for this, that I can call like: $ timegrep 22:30-02:00 /logs/something.log ...and have it pull out the lines from 22:30, onward across the midnight boundary, until 2am the next day. There are a few caveats: I don't want to have to bother typing the date(s) on the command line, just the times. The program should be smart enough to figure them out. The log date format doesn't include the year, so it should guess based on the current year, but nonetheless do the right thing around New Year's Day. I want it to be fast -- it should use the fact that the lines are in order to seek around in the file and use a binary search. Before I spend a bunch of time writing this, does it already exist?

  Read the article

• What methods are available for updating a non-Internet-connected VMWare ESXi host?

  - by romandas

  I have a stand-alone installation of VMWare vSphere Essentials, with a vCenter Server and 3 ESXi 4.0 host servers. The environment is intended to remain as a stand-alone network, with the exception that I can "float" a workstation or server between the 'Net and the VMWare network for patches and maintenance. With other installations, where the Internet is available, I've used the vSphere Host Update utility to connect to VMWare and then apply the patches to the ESXi hosts. My problem is that this utility does not seem to function if it cannot connect to both VMWare and the ESXi host at the same time, as the scan for patches function will not scan the server without connecting to VMWare's site to sync its repository first. Even if I sync it, disconnect from the 'Net and connect to the VMWare network, it still won't scan hosts for required patches -- it will prompt for syncing with VMWare and if you click No to syncing, the scan does not occur. Does anyone know of other options for updating the ESXi hosts in some automated fashion? I believe I can manually pull down required patches and apply them, but this will not scale well, and in the future I'm sure I'll want something a bit more scalable.

  Read the article

• Any dangers in using DDR memory with a higher frequency than the FSB?

  - by raw_noob

  I'm looking to upgrade memory in an older motherboard. The processor is an AMD Sempron 2500+ with a maximum speed of 333/166MHz. The motherboard is an MSI MS-7061 (KV3M-V), which accepts up to 2Gb of DDR memory maximum PC2700 in 2 slots and has a maximum FSB of 333MHz. The board does not have dual-channel support. Existing memory includes a stick of 512Mb PC3200, which seems to be running OK (presumably at PC2700) but is rated 200MHz, which is below the FSB speed. The other stick is 256Mb PC2100/133MHz, again below the FSB speed. (All figures from CPU-Z.) I have a chance to acquire a single used stick of PC3200/400MHz memory very cheaply. Crucial's system scanner seems to suggest that this will be OK with my system, but other sites have suggested that running memory with a higher frequency than the FSB can cause instability. Is this true? Would I be better waiting until I can buy the correct PC2700/333MHz stick? I'm assuming that the mixed memory I have at present is running as 768Mb at 133MHz. Is this a reasonable assumption? If so, would you expect the performance differences between 768Mb/133MHz and 1Gb/333MHz to be very noticeable? If I install the new 1Gb/400 or 333MHz stick in slot 1, am I right in thinking that adding back the existing 512Mb/200MHz stick in slot 2 would pull the whole 1.5Gb system memory speed down to 200MHz? If so, which would be better - 1.5Gb/200MHz, or the single 1Gb stick at the full 333MHz that the FSB permits? Is more headroom more important than extra speed? Any help - or even opinions - gratefully received. I can't find reliable information, and I can't afford to make expensive mistakes.

  Read the article

• Privacy, VPN and routers

  - by user123189

  Ever since this ACTA push-up the things are starting to heat up around torrents and privacy. I am using Tribler now, but this is not secure enough for me. Not enough privacy. I've been using in the past a swedish VPN PPTP connection. What I observed is that, when the VPN connection was down, Internet traffic wasn't cut off, rather the downloads were continuing, this time with my real IP, wearing off my protection. 1st : How to enforce a VPN connection that will cut all traffic when down? That is, the moment the connection is down, all internet traffic should cease as if I'd pull the network plug out. 2nd: Is PPTP good enough or should I ask for SSTP or IKEV2 ? 3rd: Should I disable IPv6 ? Is VPN no longer private if I keep IPv6 active? I 'heard some stuff' about dual vpn routers to be able to improve privacy; but nothing more about how to configure one for such a task. 4th: Is there any kind of "black box" hardware equipment that can be used in hiding IP, encrypting traffic and so on ?

  Read the article

• How to organize deployment process in Chef-controlled environment?

  - by Alex

  I have a web Linux-based infrastructure which consists of 15 virtual machines and over 50 various services. It is fully controlled by Chef. Most of the services are developed internally. Basically the current deployment process is triggered by a shell script. A build system (a mix of Python and shell scripts) packages the services as .deb files and puts these packages into a repo. It runs apt-get update on all 15 nodes then because the standard Chef apt cookbook only runs apt-get once per day and we definitely do not want to run apt-get update unconditionally on each chef-client wake. The build system restarts chef-client daemons on all 15 nodes finally (we need this step because of pull Chef nature). The current process has a number of drawbacks we want to address. First off, it is asynchronous because the deployment script does not check chef-client logs after restart so we don't even know if the deployment was successful. It does not even wait for Chef clients to complete the cycle. Second, we definitely do not want to force chef-client restarts on all nodes because we usually deploy only a small number of packages. And third, I am not quite sure using chef-client for deployment is legitimate, probably we are just doing it wrong from the start. Please share your thoughts/experience.

  Read the article

• Automated Linux VMs on Hyper-V 2012

  - by Mick

  I have a requirement to create a ton of linux VMs for our customers (we run managed infrastructure) on Hyper-V 2012 in the coming months and I have an issue with automating it. Here is how I need it to work: User accesses their web page and creates a VM. VM is created with a unique IP and name User logs in over SSH I know Hyper-V quite well and can work with powershell and am a C# programmer so the development side of things is taken care of. I also know enough about Linux to be at least competent: I have used it on and off for a number of years but not done anything Enterprise-level with it. All this can be done easily by manual processes but I need to be able to script or program this to automate it as there could be hundreds of them being created but I don't know how. My first thought is to have a database with random-generated names and IPs already created but I don't know how to get a Linux VM to boot up and grab one from the database... I suppose a Kickstart script would take care of it but I don't know what to do from there. Here is what is bouncing around in my head: Create a std linux build. - Easy to do Someone clicks "Create VM" and I pull a name and IP from the database and write it to a kickstart script. - Easy to do I could then open the template VHDX file and copy in the script and then save it. - Not sure if possible User boots up new VM and the kickstart script gives it the name and IP I assigned it. My problem is that I don't know how to open a VHDX file and insert a kickstart script into it... can't figure it out. I am reaching here and this solution may be miles off... I am more used to creating Windows VMs with scripts and so on which i am more familiar with... any help would be appreciated. Thanks Mick

  Read the article

• DRBD stacked resources: recovering from failure

  - by Marcus Downing

  We're running a stacked four-node DRBD setup like this: A --> B | | v v C D This means three DRBD resources running across these four servers. Servers A and B are Xen hosts running VMs, while servers C and D are for backups. A is in the same datacentre as C. From server A to server C, in the first datacentre, using protocol B From server B to server D, in the second datacentre, using protocol B From server A to server B, different datacentres, stacked resource using protocol A First question: booting a stacked resource We haven't got any vital data running on this setup yet - we're still making sure it works first. This means simulating power cuts, network outages etc and seeing what steps we need to recover. When we pull the power out of server A, both resources go down; it attempts to bring them back up at next boot. However, it only succeeds at bringing up the lower-level resource, A-C. The stacked resource A-B doesn't even try to connect, presumably because it can't find the device until it's a connected primary on the lower level. So if anything goes wrong we need to manually log in and bring that resource up, then start the virtual machine on top of it. Second question: setting the primary of a stacked resource Our lower-level resources are configured so that the right one is considered primary: resource test-AC { on A { ... } on C { ... } startup { become-primary-on A; } } But I don't see any way to do the same with a stacked resource, as the following isn't a valid config: resource test-AB { stacked-on-top-of test-AC { ... } stacked-on-top-of test-BD { ... } startup { become-primary-on test-AC; } } This too means that recovering from a failure requires manual intervention. Is there no way to set the automatic primary for a stacked resource?

  Read the article

• Error compiling PHP 5.5.9 on CentOS 6.5 during make command

  - by Chris Mancini

  Here is the error message: cc: internal compiler error: Killed (program cc1) Please submit a full bug report, with preprocessed source if appropriate. See <file:///usr/share/doc/gcc-4.6/README.Bugs> for instructions. make: *** [ext/fileinfo/libmagic/apprentice.lo] Error 1 The very last thing make was processing is apprentice.lo which appears to be part of the image manipulation libraries (maybe?). I am using Ansible to provision my instance. It is a Digital Ocean single core 512MB VM. I have been using vagrant / ansible with the same config locally for dev and it has compiled fine, this is the first cloud VM I am attempting to provision. The only difference is the base image for my DO server is coming from DO and for my local dev, I built my own Vagrant box via VirtualBox from a stock CentOS basic server install. I pull it down from my DropBox. The problem has been experienced by others and reported as a php bug report My php ansible role up to the error: --- - name: Download php source get_url: url={{ php_source_url }} dest=/tmp register: get_url_result - name: untar the source package command: tar -xvf php-{{ php_version }}.tar.gz chdir=/tmp when: get_url_result.changed or php_reinstall - name: configure php 5.5 command: > ./configure --prefix={{ php_prefix }} --with-config-file-path={{ php_config_file_path }} --enable-fpm --enable-ftp --enable-mbstring --enable-pdo --enable-soap --enable-sockets=shared --enable-zip --with-curl --with-fpm-group={{ nginx_group }} --with-fpm-user={{ nginx_user }} --with-freetype-dir=/usr/lib64/ --with-gd --with-jpeg-dir=/usr/lib64/ --with-libdir=lib64 --with-mcrypt --with-openssl --with-pdo-mysql --with-pear --with-readline --with-tidy --with-xsl --with-zlib --without-pdo-sqlite --without-sqlite3 chdir=/tmp/php-{{ php_version }} when: get_url_result.changed or php_reinstall - name: make clean when reinstalling command: make clean chdir=/tmp/php-{{ php_version }} when: php_reinstall - name: make php command: make chdir=/tmp/php-{{ php_version }} when: get_url_result.changed or php_reinstall Thanks in advance for any help. :)

  Read the article

• How to import a text file into powershell and email it, formatted as HTML

  - by Don

  I'm trying to get a list of all Exchange accounts, format them in descending order from largest mailbox and put that data into an email in HTML format to email to myself. So far I can get the data, push it to a text file as well as create an email and send to myself. I just can't seem to get it all put together. I've been trying to use ConvertTo-Html but it just seems to return data via email like "pageFooterEntry" and "Microsoft.PowerShell.Commands.Internal.Format.AutosizeInfo" versus the actual data. I can get it to send me the right data if i don't tell it to ConvertTo-Html, just have it pipe the data to a text file and pull from it, but it's all ran together with no formatting. I don't need to save the file, i'd just like to run the command, get the data, put it in HTML and mail it to myself. Here's what I have currently: #Connects to Database and returns information on all users, organized by Total Item Size, User $body = Get-MailboxStatistics -database "Mailbox Database 0846468905" | where {$_.ObjectClass -eq “Mailbox”} | Sort-Object TotalItemSize -Descending | ft @{label=”User”;expression={$_.DisplayName}},@{label=”Total Size (MB)”;expression={$_.TotalItemSize.Value.ToMB()}} -auto | ConvertTo-Html #Pause for 5 seconds for Exchange write-host -foregroundcolor Green "Pausing for 5 seconds for Exchange" Start-Sleep -s 5 $toemail = "[email protected]" # Emails report to this address. $fromemail = "[email protected]" #Emails from this address. $server = "Exchange.company.com" #Exchange server - SMTP. #Email the report. $email = New-Object System.Net.Mail.MailMessage $email.IsBodyHtml = $True $email.To.Add($toemail) $email.From = $fromemail $email.Subject = "Exchange Mailbox Sizes" $email.Body = $body $client = New-Object System.Net.Mail.SmtpClient $server $client.UseDefaultCredentials = $true $client.Send($email) Any thoughts would be helpful, thanks!

  Read the article

• Backup files from Linux client to Windows Server

  - by Andrew

  I'm trying to backup my files from my Linux box to my Windows Server 2008 as a push, and when I delete them from my Linux box, they remain on my Windows Server. I've found lots of sources that are similar, but most results were from Windows to Linux. I managed to find slightly more similar cases like Using rsync and cygwin to Sync Files from a Linux Server to a Windows Notebook PC, and rsync from Windows PC to remote Linux server, with the most similar being a backup from Linux to Windows Server, but through a pull from the Windows Server. Initially, I used Unison because I thought having the 2-way capability would come in handy, and I would just have to set some configurations to make it 1-way. Unfortunately, I couldn't find the right configuration, and only managed to synchronize using the command unison "profile" -ui text -auto -silent. When I deleted the files on my Linux box, the files in the Server got deleted too, which of course, isn't what I want. When I tried to find any options for Unison, I only discovered the -force option, which didn't help, since what I wanted was an incremental update to the Server. I found out I could achieve this from using rsync and the -a option (archive), which would keep adding files even if I deleted them from my Linux box. I installed Cygwin on my Windows Server, configured an SSH daemon, but I can't seem to get it working. I've also already configured Windows Firewall to open port 22 (both inbound and outbound). I used the following command from my Linux box: rsync -avrzn /folder/to/be/backed/up/ [email protected]:/cygdrive/c/place/to/store/backed/up/files (a - archive, v - verbose, r - recurse into subdirectories, z - compress, n - dryrun) but it just won't work. Can anyone help me out? I don't mind using either Unison or rsync, as long as it achieves what I want.

  Read the article

• keyboard intermittently stops working, even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash a couple of the ctrl+alt+windows type keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu, but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) *Unplugging & reconnecting keyboard does NOT fix it. *Connecting a different keyboard does NOT fix it. That one won't work, either. *Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. *Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears, they keyboard won't work, and neither will the icon to pull up the on-screen keyboard. Otherwise my mouse can click around just fine. I can only log onto a non-password protected account. *Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. *Clearing my Chrome browsing data stopped the problem from recurring for a week or so. *I use Avira free antivirus software, and repeated scans turn up nothing fishy. *I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. The only thing I suspect is something in Google Chrome -- I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• central apache log analysis of many hosts

  - by Jason Antman

  We have 30+ apache httpd servers, and are looking to perform analysis on the logs both for historical trending and near "real time" monitoring/alerting. I'm mainly interested in things like error rates (4xx/5xx), response time, overall request rate, etc. but it would also be very useful to pull out more compute-intensive statistics like unique client IPs and user agents per unit of time. I'm leaning towards building this as a centralized collector/server/storage, and am also considering the possibility of storing non-apache logs (i.e. general syslog, firewall logs, etc.) in the same system. Obviously a large part of this will probably have to be custom (at least the connection between pieces and the parsing/analysis we do), but I haven't been able to find much information on people who have done stuff like this, at least at shops smaller than Google/Facebook/etc. who can throw their log data into a hundred-node compute cluster and run Map/Reduce on it. The main things I'm looking for are: - All open source - Some way of collecting logs from apache machines that isn't too resource-intensive, and transports them relatively quickly over the network - Some way of storing them (NoSQL? key-value store?) on the backend, for a given amount of time (and then rolling them up into historical averages) - In the middle of this, a way of graphing in near-real-time (probably also with some statistical analysis on it) and hopefully alerting off of those graphs. Any suggestions/pointers/ideas, to either "products"/projects or descriptions of how other people do this would be greatly helpful. Unfortunately, we're not exactly a new-age-y devops shop, lots of old stuff, homogeneous infrastructure, and strained boxes.

  Read the article

• Disk doesn't contain a valid partition table

  - by Jeevan Dongre

  I was running a m1.small instance ec2 ubuntu instance. I was running out of disk space, so I upgraded my instance to medium. When I upgraded I actually got 429.5 GB of space and after that I added 10 gb of volume too. When I run the "sudo fdisk -l" command I got this results. Disk /dev/sda1: 8589 MB, 8589934592 bytes 255 heads, 63 sectors/track, 1044 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda1 doesn't contain a valid partition table Disk /dev/sda2: 429.5 GB, 429461078016 bytes 255 heads, 63 sectors/track, 52212 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda2 doesn't contain a valid partition table Disk /dev/sdf: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 sda1 is the primary parition and sda2 is what I got added upgrading my system to medium. But the problem persists, I am not able to pull the code from git, it is giving me this error. remote: Counting objects: 409, done. remote: Compressing objects: 100% (236/236), done. fatal: write error: No space left on device fatal: index-pack failed

  Read the article

< Previous Page | 73 74 75 76 77 78 79 80 81 82 83 84  | Next Page >