Search Results

Search found 10207 results on 409 pages for 'ethernet switch'.

Page 78/409 | < Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85 | Next Page >

Vyatta masquerade out bridge interface

- by miquella

We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

Read the article
Slow tracepath on local LAN

- by Simone Falcini

I am on EXSi and I have 2 instances: Ubuntu and CentOS. These are the network configurations Ubuntu eth0 Link encap:Ethernet HWaddr 00:50:56:00:1f:68 inet addr:212.83.153.71 Bcast:212.83.153.71 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76059 errors:0 dropped:26 overruns:0 frame:0 TX packets:7224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6482760 (6.4 MB) TX bytes:2080684 (2.0 MB) eth1 Link encap:Ethernet HWaddr 00:0c:29:46:5a:f2 inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:252 errors:0 dropped:0 overruns:0 frame:0 TX packets:608 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:42460 (42.4 KB) TX bytes:82474 (82.4 KB) /etc/iptables.conf *nat :PREROUTING ACCEPT [142:12571] :INPUT ACCEPT [5:1076] :OUTPUT ACCEPT [8:496] :POSTROUTING ACCEPT [8:496] -A POSTROUTING -s 192.168.1.0/24 -o eth0 -j MASQUERADE COMMIT *filter :INPUT ACCEPT [2:72] :FORWARD ACCEPT [4:336] :OUTPUT ACCEPT [6:328] -A INPUT -i eth1 -p tcp -j ACCEPT -A INPUT -i eth1 -p udp -j ACCEPT -A INPUT -i eth0 -p tcp --dport ssh -j ACCEPT COMMIT CentOS eth0 Link encap:Ethernet HWaddr 00:0C:29:74:1C:55 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe74:1c55/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:499 errors:0 dropped:0 overruns:0 frame:0 TX packets:475 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68326 (66.7 KiB) TX bytes:82641 (80.7 KiB) The main problem is that if i execute this command from the CentOS instance ssh 192.168.1.2 it takes more than 20s to connect. It seems like it's routing the connection to the wrong network. What could it be? Thanks!

Read the article
Forward all traffic from one IP to another Ip on OS X

- by Josh

This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

Read the article
How to set static ip address on vmware for NAT guest vms from an ubuntu Host dhcp server?

- by javadba

I need to configure various linux flavor NAT'ed guest vm's to have static ip addresses provided by the Ubuntu host. The vmware documentation punts on this topic, deferring to "see the man pages for your linux distribution". But the generic pages for "my linux distro" do not know about the special stuff for vmware e.g. vmnet8. Pointers from someone who just knows how to do this would be much appreciated. Here is the /etc/vmware/vmnet8/dhcpd/dhcpd.conf: allow unknown-clients; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours subnet 192.168.238.0 netmask 255.255.255.0 { range 192.168.238.128 192.168.238.254; option broadcast-address 192.168.238.255; option domain-name-servers 192.168.238.2; option domain-name localdomain; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours option netbios-name-servers 192.168.238.2; option routers 192.168.238.2; } host vmnet8 { hardware ethernet 00:50:56:C0:00:08; fixed-address 192.168.238.1; option domain-name-servers 0.0.0.0; option domain-name ""; option routers 0.0.0.0; } Fromt the dhcpd.conf documentation, we are supposed to add an entry for static hosts similar to the following: host mystatichostonee { hardware ethernet 00:20:6B:C7:9B:E4; fixed-address 192.168.238.101; } host mystatichosttwo { hardware ethernet 00:23:7a:C7:9c:F2; fixed-address 192.168.238.102; } But notice that the vmnet8 entry in the vmware-generated dhcpd.conf already is set to fixed-address. I don't know how to add the specifics for my hosts to that vmnet8 entry: do they become nested?

Read the article
VMWare use of Gratuitous ARP REPLY

- by trs80

I have an ESXi cluster that hosts several Windows Server VMs and around 30 Windows workstation VMs. Packet captures show a high number of ARP replies of the form: -sender_ip: VM IP -sender_mac: VM virtual MAC -target_ip: 0.0.0.0 -target_mac: Switch interface MAC The specific addresses aren't really a concern -- they're all legitimate and we're not having any problems with communications (most of the questions surrounding GARP and VMWare have to do with ping issues, a problem we don't have). I'm looking for an explanation of the traffic pattern in an environment that functions as expected. So the question is why would I see a high number of unsolicited ARP replies? Is this a mechanism VMWare uses for some purpose? What is it? Is there an alternative? EDIT: Quick diagram: [esxi]--[switch vlan]--[inline IDS]--[fw]--(rest of network) The IDS is complaining about these unsolicited ARPs. Several IDS vendors trigger on ARP replies without a prior request, or for ARP replies that have a target IP of 0.0.0.0. The target MAC in these replies is the VLAN interface on the switch. Capture points: -The IDS grabs the offending packets -The FW can see the same ones -A VM on the ESXi host does not see these, although there is an ARP request for a specific IP on the ESXi host that has source_ip=0.0.0.0 and source_mac=[switch vlan interface]. I can't share the captures, unfortunately. Really I'm interested in finding out if this is normal for an ESXi deployment.

Read the article
bond0:0 + define virtual IP

- by yael

hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

Read the article
bond0:0 + define virtual IP

- by yael

hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

Read the article
How to connect computers to a network printer behind a router?

- by kokbira

General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

Read the article
SSH Connection Error : No route to host

- by dewbot

There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

Read the article
Virtual box host-only adapter configuration

- by Xoundboy

I have VirtualBox 4 running on Win 7 with a Centos 6 guest VM set up for hosting my dev server. When I'm connected to my home network the guest can be accessed via a static IP address that I configured (192.168.56.2), but not when I'm in the office. I'm guessing that the DHCP server in the office doesn't have a gateway configured for the 192.168.56.x IP range. I read something about the VB host-only adapter that should allow me to set this guest VM up in such a way that I don't need to be on any network to be able to access the guest from the host using a static IP. I've not been able to find out exactly how to configure this though. Can anyone give me an example configuration, thanks. UPDATE: Thanks for your responses. I've now set up a single virtual network adapter in VirtualBox and set it to host-only: C:\Users\Ben>vboxmanage list hostonlyifs Name: VirtualBox Host-Only Ethernet Adapter GUID: d419ef62-3c46-4525-ad2d-be506c90459a Dhcp: Disabled IPAddress: 192.168.56.2 NetworkMask: 255.255.255.0 IPV6Address: fe80:0000:0000:0000:78e3:b200:5af3:2a57 IPV6NetworkMaskPrefixLength: 64 HardwareAddress: 08:00:27:00:94:e8 MediumType: Ethernet Status: Up VBoxNetworkName: HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter On the guest I've set up eth0 to use the same IP address as the host-only adapter (192.168.56.2) but when I try to log in using Putty I still get "Network Error : connection refused". VirtualBox DHCP servier is enabled but I can't ping the gateway (192.168.56.1) from either host nor guest. There's no firewall running on either OS. What next?

Read the article
Libvirt/KVM in NAT: can't access from host (and can't forward)

- by SharkWipf

I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

Read the article
bond0:0 + define virtual IP

- by yael

in my Linux server I have the following: Linux Version - RedHat-Linux- 5.3.0.0 (this Linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it possible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

Read the article
Router intermittently failing

- by nomen

My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

Read the article
Centos VM serving multiple public IP: how to configure network interface?

- by Glasnhost

I have a Centos 5.6 VM (Vsphere client) already responding to two different public IPs on eth0 and eth0:1 and I'm trying to add eth0:2. I copied the eth0 config file and restarted the network service. I don't understand which other steps are needed... ifconfig eth0 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.10 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163371837 errors:77 dropped:0 overruns:0 frame:0 TX packets:168210961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1891221045 (1.7 GiB) TX bytes:855899500 (816.2 MiB) Interrupt:59 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.11 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 eth0:2 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.12 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:188976973 errors:0 dropped:0 overruns:0 frame:0 TX packets:188976973 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2015642664 (1.8 GiB) TX bytes:2015642664 (1.8 GiB) more /etc/resolv.conf nameserver 10.1.12.1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.12.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.1.12.1 0.0.0.0 UG 0 0 0 eth0

Read the article
Change "Show Desktop" to "Minimize All"

- by V0R73X

I'd like to use Alt-Tab a lot when I'm programming under Windows. It's the quickest method to switch between windows. However, there's one annoying thing about this, and that is when I switch over to "Desktop" using Alt-Tab, Windows uses the "Show Desktop" command instead of minimizing all Windows. I personally hate Show Desktop, since it creates a separate window on top of all the other windows which captures a live display of desktop, and this causes all the widgets I have on the desktop to be hidden under this live window, and I LOVE my widgets. An ideal behavior for when I switch tabs to Desktop using Alt-Tab would be the "Minimize All" behavior, which simply minimizes all windows, leaving me with my actual desktop, which sits behind everything. In order to achieve this, I have to move my fingers across the keyboard, and press Win+M. This decreases my efficiency by .5 seconds, which is a LOT of time. How can I tell windows to use "Minimize All" rather than "Show Desktop" when I use my good ol' Alt-Tab functionality to switch over to desktop and save .5 seconds in time?

Read the article
Sublime text 2 syntax highlighter?

- by BigSack

I have coded my first custom syntax highlighter for sublime text 2, but i don't know how to install it. It is based on notepad++ highlighter found here https://70995658-a-62cb3a1a-s-sites.googlegroups.com/site/lohanplus/files/smali_npp.xml?attachauth=ANoY7criVTO9bDmIGrXwhZLQ_oagJzKKJTlbNDGRzMDVpFkO5i0N6hk_rWptvoQC1tBlNqcqFDD5NutD_2vHZx1J7hcRLyg1jruSjebHIeKdS9x0JCNrsRivgs6DWNhDSXSohkP1ZApXw0iQ0MgqcXjdp7CkJJ6pY_k5Orny9TfK8UWn_HKFsmPcpp967NMPtUnd--ad-BImtkEi-fox2tjs7zc5LabkDQ%3D%3D&attredirects=0&d=1 <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>fileTypes</key> <array> <string>smali</string> </array> <dict> <key>Word1</key> <string>add-double add-double/2addr add-float add-float/2addr add-int add-int/2addr add-int/lit16 add-int/lit8 add-long add-long/2addr aget aget-boolean aget-byte aget-char aget-object aget-short aget-wide and-int and-int/2addr and-int/lit16 and-int/lit8 and-long and-long/2addr aput aput-boolean aput-byte aput-char aput-object aput-short aput-wide array-length check-cast cmp-long cmpg-double cmpg-float cmpl-double cmpl-float const const-class const-string const-string-jumbo const-wide const-wide/16 const-wide/32 const-wide/high16 const/16 const/4 const/high16 div-double div-double/2addr div-float div-float/2addr div-int div-int/2addr div-int/lit16 div-int/lit8 div-long div-long/2addr double-to-float double-to-int double-to-long execute-inline fill-array-data filled-new-array filled-new-array/range float-to-double float-to-int float-to-long goto goto/16 goto/32 if-eq if-eqz if-ge if-gez if-gt if-gtz if-le if-lez if-lt if-ltz if-ne if-nez iget iget-boolean iget-byte iget-char iget-object iget-object-quick iget-quick iget-short iget-wide iget-wide-quick instance-of int-to-byte int-to-char int-to-double int-to-float int-to-long int-to-short invoke-direct invoke-direct-empty invoke-direct/range invoke-interface invoke-interface/range invoke-static invoke-static/range invoke-super invoke-super-quick invoke-super-quick/range invoke-super/range invoke-virtual invoke-virtual-quick invoke-virtual-quick/range invoke-virtual/range iput iput-boolean iput-byte iput-char iput-object iput-object-quick iput-quick iput-short iput-wide iput-wide-quick long-to-double long-to-float long-to-int monitor-enter monitor-exit move move-exception move-object move-object/16 move-object/from16 move-result move-result-object move-result-wide move-wide move-wide/16 move-wide/from16 move/16 move/from16 mul-double mul-double/2addr mul-float mul-float/2addr mul-int mul-int/2addr mul-int/lit8 mul-int/lit16 mul-long mul-long/2addr neg-double neg-float neg-int neg-long new-array new-instance nop not-int not-long or-int or-int/2addr or-int/lit16 or-int/lit8 or-long or-long/2addr rem-double rem-double/2addr rem-float rem-float/2addr rem-int rem-int/2addr rem-int/lit16 rem-int/lit8 rem-long rem-long/2addr return return-object return-void return-wide rsub-int rsub-int/lit8 sget sget-boolean sget-byte sget-char sget-object sget-short sget-wide shl-int shl-int/2addr shl-int/lit8 shl-long shl-long/2addr shr-int shr-int/2addr shr-int/lit8 shr-long shr-long/2addr sparse-switch sput sput-boolean sput-byte sput-char sput-object sput-short sput-wide sub-double sub-double/2addr sub-float sub-float/2addr sub-int sub-int/2addr sub-int/lit16 sub-int/lit8 sub-long sub-long/2addr throw throw-verification-error ushr-int ushr-int/2addr ushr-int/lit8 ushr-long ushr-long/2addr xor-int xor-int/2addr xor-int/lit16 xor-int/lit8 xor-long xor-long/2addr</string> </dict> <dict> <key>Word2</key> <string>v0 v1 v2 v3 v4 v5 v6 v7 v8 v9 v10 v11 v12 v13 v14 v15 v16 v17 v18 v19 v20 v21 v22 v23 v24 v25 v26 v27 v28 v29 v30 v31 v32 v33 v34 v35 v36 v37 v38 v39 v40 v41 v42 v43 v44 v45 v46 v47 v48 v49 v50 p0 p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26 p27 p28 p29 p30</string> </dict> <dict> <key>Word3</key> <string>array-data .catch .catchall .class .end .end\ local .enum .epilogue .field .implements .line .local .locals .parameter .prologue .registers .restart .restart\ local .source .subannotation .super</string> </dict> <dict> <key>Word4</key> <string>abstract bridge constructor declared-synchronized enum final interface native private protected public static strictfp synchronized synthetic system transient varargs volatile</string> </dict> <dict> <key>Word4</key> <string>("0)"0</string> </dict> <dict> <key>Word5</key> <string>.method .annotation .sparse-switch .packed-switch</string> </dict> <dict> <key>word6</key> <string>.end\ method .end\ annotation .end\ sparse-switch .end\ packed-switch</string> </dict> <dict> <key>word7</key> <string>" ( ) , ; { } ></string> </dict> <key>uuid</key> <string>27798CC6-6B1D-11D9-B8FA-000D93589AF6</string> </dict> </plist>

Read the article
Media Disconnected Networking Issue

- by Chris

After rearranging my physical network in my apartment my Windows Vista machine can no longer connect to the network. I have tested all of the cabling by connecting other devices and everything is fine. I'm able to connect using other computers, I've even tested a brand new ethernet adapter and the network status still reads "media disconnected". I have no idea where to go from here. My setup is as follows: Cable modem - router - hardwired ethernet cable to computer.

Read the article
KVM + Cloudmin + IpTables

- by Alex

I have a KVM virtualization on a machine. I use Ubuntu Server + Cloudmin (in order to manage virtual machine instances). On a host system I have four network interfaces: ebadmin@saturn:/var/log$ ifconfig br0 Link encap:Ethernet HWaddr 10:78:d2:ec:16:38 inet addr:192.168.0.253 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::1278:d2ff:feec:1638/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:589337 errors:0 dropped:0 overruns:0 frame:0 TX packets:334357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:753652448 (753.6 MB) TX bytes:43385198 (43.3 MB) br1 Link encap:Ethernet HWaddr 6e:a4:06:39:26:60 inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::6ca4:6ff:fe39:2660/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16995 errors:0 dropped:0 overruns:0 frame:0 TX packets:13309 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2059264 (2.0 MB) TX bytes:1763980 (1.7 MB) eth0 Link encap:Ethernet HWaddr 10:78:d2:ec:16:38 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:610558 errors:0 dropped:0 overruns:0 frame:0 TX packets:332382 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:769477564 (769.4 MB) TX bytes:44360402 (44.3 MB) Interrupt:20 Memory:fe400000-fe420000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:239632 errors:0 dropped:0 overruns:0 frame:0 TX packets:239632 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50738052 (50.7 MB) TX bytes:50738052 (50.7 MB) tap0 Link encap:Ethernet HWaddr 6e:a4:06:39:26:60 inet6 addr: fe80::6ca4:6ff:fe39:2660/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17821 errors:0 dropped:0 overruns:0 frame:0 TX packets:13703 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:2370468 (2.3 MB) TX bytes:1782356 (1.7 MB) br0 is connected to a real network, br1 is used to create a private network shared between guest systems. Now I need to configure iptables for network access. First of all I allow ssh sessions on port 8022 on the host system, then I allow all connections in state RELATED, ESTABLISHED. This is working ok. I install another system as guest, it's IP address is 192.168.10.2, and now I have two problems: I want to allow the access from this host to the outside world, cannot accomplish this. I can ssh from the host. I want to be able to ssh to the guest from the outside world using 8023 port. Cannot accomplish this. Full iptables configuration is following: ebadmin@saturn:/var/log$ sudo iptables --list [sudo] password for ebadmin: Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere tcp dpt:8022 ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED LOG all -- anywhere anywhere LOG level warning Chain FORWARD (policy ACCEPT) target prot opt source destination LOG all -- anywhere anywhere LOG level warning Chain OUTPUT (policy ACCEPT) target prot opt source destination LOG all -- anywhere anywhere LOG level warning ebadmin@saturn:/var/log$ sudo iptables -t nat --list Chain PREROUTING (policy ACCEPT) target prot opt source destination DNAT tcp -- anywhere anywhere tcp spt:8023 to:192.168.10.2:22 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination The worst of all is that I don't know how to interpret iptables logs. I don't see the final decision of the firewall. Need help urgently.

Read the article
ovs-vsctl: "eth0" is not a valid UUID

- by Przemek Lach

I'm trying to setup an open v-switch inside my Ubuntu 12.04 Server VM. I have created three interfaces for this VM and I want to create a port mirror inside of the VM using these there interfaces and open v-switch. There are three Host-Only Adapters: eth0, eth1, eth2. The idea is that three other VM's will be connected to these adapters. One of these VM's will stream UDP video to eth0 and I want the vswitch'd VM to mirror those packets from eth0 onto eth1 and eth2. Each of the VM's connected to eth1 and eth2 will get the same video stream. I performed the following steps to install open v-switch: $ apt-get install python-simplejson python-qt4 python-twisted-conch automake autoconf gcc uml-utilities libtool build-essential $ apt-get install build-essential autoconf automake pkg-config $ wget http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ tar xf http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ cd http://openvswitch.org/releases/openvswitch-1.7.1.tar.gz $ apt-get install libssl-dev iproute tcpdump linux-headers-`uname -r` $ ./boot.sh $ ./configure - -with-linux=/lib/modules/`uname -r`/build $ make $ sudo make install After installation I configured as follows: $ insmod datapath/linux/openvswitch.ko $ sudo touch /usr/local/etc/ovs-vswitchd.conf $ mkdir -p /usr/local/etc/openvswitch $ ovsdb-tool create /usr/local/etc/openvswitch/conf.db Then I started the server: $ ovsdb-server /usr/local/etc/openvswitch/conf.db \ --remote=punix:/usr/local/var/run/openvswitch/db.sock \ --remote=db:Open_vSwitch,manager_options \ --private-key=db:SSL,private_key \ --certificate=db:SSL,certificate \ --bootstrap-ca-cert=db:SSL,ca_cert --pidfile --detach --log-file $ ovs-vsctl –no-wait init (run only once) $ ovs-vswitchd --pidfile --detach The above steps I got from this tutorial and it all worked fine. I then proceeded to add a port mirror based on the open v-switch documentation under Port Mirroring. I successfully completed the following commands: $ ovs-vsctl add-br br0 $ ovs-vsctl add-port br0 eth0 $ ovs-vsctl add-port br0 eth1 $ ovs-vsctl add-port br0 eth2 $ ifconfig eth0 promisc up $ ifconfig eth1 promisc up $ ifconfig eth2 promisc up At this point when I run ovs-vsctl show I get the following: 75bda8c2-b870-438b-9115-e36288ea1cd8 Bridge "br0" Port "br0" Interface "br0" type: internal Port "eth0" Interface "eth0" Port "eth2" Interface "eth2" Port "eth1" Interface "eth1" And when I run ifconfig I get the following: eth0 Link encap:Ethernet HWaddr 08:00:27:9f:51:ca inet6 addr: fe80::a00:27ff:fe9f:51ca/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth1 Link encap:Ethernet HWaddr 08:00:27:53:02:d4 inet6 addr: fe80::a00:27ff:fe53:2d4/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth2 Link encap:Ethernet HWaddr 08:00:27:cb:a5:93 inet6 addr: fe80::a00:27ff:fecb:a593/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:17 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1494 (1.4 KB) TX bytes:468 (468.0 B) eth3 Link encap:Ethernet HWaddr 08:00:27:df:bb:d8 inet addr:192.168.1.139 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fedf:bbd8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2211 errors:0 dropped:0 overruns:0 frame:0 TX packets:1196 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:182987 (182.9 KB) TX bytes:125441 (125.4 KB) NOTE: I use eth3 as a bridge adapter for SSH'ing into the VM. So now, I think I've done everything correctly but when I try to create the bridge using the following command: $ ovs-vsctl -- set Bridge br0 mirrors=@m -- --id=@eth0 get Port eth0 -- --id=@eth1 get Port eth1 -- --id=@m create Mirror name=app1Mirror select-dst-port=eth0 select-src-port=@eth0 output-port=@eth1,eth2 I get the following error: ovs-vsctl: "eth0" is not a valid UUID I don't understand why it's not able to find the interfaces?

Read the article
How do I connect my Windows XP laptop to the internet?

- by rubysiddhi

Hello fellow super users, The Past I have a Acer Travelmate 2300 laptop running Windows XP. 6 months ago I moved into a new apartment and got a new internet connection set up. After getting an internet connection installed in my apartment I reinstalled Windows XP and at the same time wiped my drive clean losing all the original Acer software and drivers. Once XP was reinstalled I had to find all the drivers again to get the Travelmate laptop connected to the internet. So, using my Vista laptop which was connected fine, I went to the Acer Travelmate Series drivers download page to download the necessary drivers. I transferred them to my Acer XP machine and installed them the best I could (there were no easy instructions so I just had to find all the executables and run them). I eventually got connected to the internet but not exactly in the way I had hoped for. The Present To be connected to the internet I need to have an Ethernet cord connecting my computer (via the Ethernet port) to my router. This is a problem since it defeats the purpose of having a Wireless LAN card in my Acer laptop. One of the programs I downloaded from the Acer Travelmate Series page was the Acer Wireless LAN Configuration Utility. This program allows me to see the current network I am connected to and all the available networks I could potentially connect to. It reminds me of XP's Wireless Network Connection window/utility where you can see all available wireless networks, refresh the network list and connect to one of the networks. I should mention that my ISP set up a security enabled wireless network with WPA. This network requires a network key if you want to connect to it. I guess my Vista computer has the network key entered into it already. The problem is that I do not know what the network key is. Now obviously you would say just contact my ISP to get the key. And I will but there is just one extra weird issue. I am able to connect to another unsecured wireless network in the Wireless Network Connection window/utility. I can be on it as long as my Ethernet cable is plugged in. So this is not really wireless is it? And this indicates that even if I do get that network key password from my ISP, I will only solve one of the two problems I have. I will only solve being able to get online as long as I am connected to my router via the Ethernet cable. The Main Questions So how do I enable my acer IPN2220 Wireless LAN Card so that I can use my Acer laptop from anywhere with in my apartment? Or should I first get the network key from my ISP to access my security enabled wireless network? And then deal with getting the acer IPN2220 Wireless LAN Card working? Hard & Learned VS Easy & Stupid Of course contacting the ISP would be easier. Have em just come in here and do there thing. The problem with that is that they do not speak English (yeah, im in Poland) and it'd be a hell of a time trying to understand what they are doing (uncomfortable looking over their shoulder). Also, I want to learn how to do this task myself so that I can fix the problem if it ever happens again. You know, be more self sufficient. I look forward to helpful replies. Thanks, Xaviour

Read the article
Wireless Connected But No Internet Connection (Ubuntu 12.04)

- by Zxy

I am using same network for 2 days and everything was normal. However, today even though it shows me as connected to the network, I do not have internet connection. If I use ethernet cable instead of wireless, I am still able to connect to the internet. Also my friends are able to connect to the wireless network and they can get internet connection. I did not update or install anything since yesterday. Therefore I do not have any idea why it is happening. Here is some information about my connection: I will be appreciate to any kind of help. root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 hid 77367 2 hid_logitech_dj,usbhid ideapad_laptop 17890 0 sparse_keymap 13658 2 acer_wmi,ideapad_laptop lib80211_crypt_tkip 17275 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event wl 2646601 0 wmi 18744 1 acer_wmi i915 414672 3 drm_kms_helper 45466 1 i915 snd_timer 28931 2 snd_pcm,snd_seq mac_hid 13077 0 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq lib80211 14040 2 lib80211_crypt_tkip,wl drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 snd 62064 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_se q,snd_timer,snd_seq_device video 19068 1 i915 mei 36570 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp atl1c 36718 0 root@ghostrider:/etc/resolvconf# nm-tool NetworkManager Tool State: connected (global) - Device: eth1 [PoliTekno] ---------------------------------------------------- Type: 802.11 WiFi Driver: wl State: connected Default: yes HW Address: AC:81:12:7F:6B:B2 Capabilities: Speed: 54 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) CnDStudios: Infra, 00:12:BF:3F:0A:8A, Freq 2412 MHz, Rate 54 Mb/s, Strength 85 WPA AIR_TIES: Infra, 00:1C:A8:6E:84:32, Freq 2462 MHz, Rate 54 Mb/s, Strength 72 WPA2 VKSS: Infra, 00:E0:4D:01:0D:47, Freq 2452 MHz, Rate 54 Mb/s, Strength 62 WPA2 PROGEDA: Infra, 00:1A:2A:60:BF:61, Freq 2462 MHz, Rate 54 Mb/s, Strength 47 WPA MobilAtolye: Infra, 72:2B:C1:65:75:3C, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 AIRTIES_WAR-141: Infra, 00:1C:A8:AB:AA:48, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 tilda_biri_yeni: Infra, 54:E6:FC:B0:3C:E9, Freq 2437 MHz, Rate 0 Mb/s, Strength 34 WEP *PoliTekno: Infra, 00:16:E3:40:C3:E4, Freq 2462 MHz, Rate 54 Mb/s, Strength 100 WPA2 AIRTIES_RJY: Infra, 00:1A:2A:BD:85:16, Freq 2462 MHz, Rate 54 Mb/s, Strength 55 WEP IPv4 Settings: Address: 0.0.0.0 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: F0:DE:F1:6C:90:65 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off root@ghostrider:/etc/resolvconf# sudo iwlist scan lo Interface doesn't support scanning. eth1 Scan completed : Cell 01 - Address: 00:16:E3:40:C3:E4 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-48 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: 00:E0:4D:01:0D:47 ESSID:"VKSS" Mode:Managed Frequency:2.452 GHz (Channel 9) Quality:4/5 Signal level:-64 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Cell 03 - Address: 00:1C:A8:AB:AA:48 ESSID:"AIRTIES_WAR-141" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-77 dBm Noise level:-95 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DDB20050F204104A0001101049001E007FC5100018DE7CF0D8B70223A62711C18926AC290E30303030303139631044000102103B0001031047001076B31BC241E953CB99C3872554425A28102100194169725469657320576972656C657373204E6574776F726B73102300074169723534343010240008312E322E302E31321042000F4154303939313131383030323832351054000800060050F20400011011000741697235343430100800020084103C000103 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 04 - Address: 72:2B:C1:65:75:3C ESSID:"MobilAtolye" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-78 dBm Noise level:-92 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: DDA20050F204104A0001101044000102103B00010310470010BC329E001DD811B28601722BC165753C1021001D48756177656920546563686E6F6C6F6769657320436F2E2C204C74642E1023001C48756177656920576972656C6573732041636365737320506F696E74102400065254323836301042000831323334353637381054000800060050F204000110110009487561776569415053100800020084103C000100 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s 24 Mb/s; 48 Mb/s Cell 05 - Address: 00:12:BF:3F:0A:8A ESSID:"CnDStudios" Mode:Managed Frequency:2.412 GHz (Channel 1) Quality:5/5 Signal level:-47 dBm Noise level:-95 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 06 - Address: 00:1C:A8:6E:84:32 ESSID:"AIR_TIES" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-56 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 07 - Address: 54:E6:FC:B0:3C:E9 ESSID:"tilda_biri_yeni" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-85 dBm Noise level:-99 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Cell 08 - Address: 18:28:61:16:57:C3 ESSID:"obilet" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-88 dBm Noise level:-99 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 09 - Address: 00:1A:2A:60:BF:61 ESSID:"PROGEDA" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-75 dBm Noise level:-98 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s eth0 Interface doesn't support scanning.

Read the article
DHCP Relay V DHCP Local Cisco v 3com

- by DefSol

Howdy, I have a client who has a WAN with 7 sites. At one site in particular, randomly about 4-5 clients do not get an IP address. The local gateway is a cisco 871 and relay's to a windows server in a Data Center running a valid scope for the subnet. If I put in a cisco 1800 and configure a dhcp scope (disabling the scope on the server) all clients get an ip address and everything is right with the world. The Wan providing keeps saying it's a local issue although we can work around with the 1800. The provider says a 3Com switch is at fault and the 1800 does not have a local switch, and because the 871 does, means the internal switching will receive a different uplink policy. The 3Com is the only managed switch in the subnet. Any ideas greatly appreciated. Reuben

Read the article
DHCP Relay V DHCP Local Cisoc v 3com

- by DefSol

Howdy, I have a client who has a WAN with 7 sites. At one site in particular, randomly about 4-5 clients do not get an IP address. The local gateway is a cisco 871 and relay's to a windows server in a Data Center running a valid scope for the subnet. If I put in a cisco 1800 and configure a dhcp scope (disabling the scope on the server) all clients get an ip address and everything is right with the world. The Wan providing keeps saying it's a local issue although we can work around with the 1800. The provider says a 3Com switch is at fault and the 1800 does not have a local switch, and because the 871 does, means the internal switching will receive a different uplink policy. The 3Com is the only managed switch in the subnet. Any ideas greatly appreciated. Reuben

Read the article
Microsoft Outlook hangs when switching input language

- by Hugo

Hello, I have two keyboard languages, Swedish and Amerikan English. Normally, I switch language by hitting [alt]+[shift] and it works like a charm. However, suddenly Microsoft Outlook has started to hang whenever I try to switch keyboard input language. Whenever i hit [alt]+[shift] or use the menu to switch language Outlook will hang indefinitely not responding. Why? and what can I do about it? I have English Windows 2000 and Outlook 2003 with the Google Search Desktop plugin.

Read the article
Locate rogue DHCP server

- by Farseeker

I know this is a serious long shot, but here we go. In the past week or so, for users connected to a particular switch in our network (there are four dumb switches all connected, and it only affects SOME, not all, users on the one switch) are getting DHCP addresses from a rogue DHCP server. I have physically checked every cable plugged into the switch in question to make sure that none of them have a router or wifi point attached to it. I know the IP of the DHCP server, but I cannot ping it, and it does not have a web interface. Does anyone have any suggestions on what I can do to locate it or shut it down? Unfortuantely all the switches are unmanaged, and as mentioned, there's no physical device (that I can find) plugged in to anything. It's getting critical, because it's screwing up the PXE boot of a whole bunch of thin clients.

Read the article

< Previous Page | 74 75 76 77 78 79 80 81 82 83 84 85 | Next Page >