Search Results

Search found 46813 results on 1873 pages for 'system shutdown'.

Page 792/1873 | < Previous Page | 788 789 790 791 792 793 794 795 796 797 798 799  | Next Page >

• How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

  - by Maharshi Raval

      I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

  Read the article

• How to organize deployment process in Chef-controlled environment?

  - by Alex

  I have a web Linux-based infrastructure which consists of 15 virtual machines and over 50 various services. It is fully controlled by Chef. Most of the services are developed internally. Basically the current deployment process is triggered by a shell script. A build system (a mix of Python and shell scripts) packages the services as .deb files and puts these packages into a repo. It runs apt-get update on all 15 nodes then because the standard Chef apt cookbook only runs apt-get once per day and we definitely do not want to run apt-get update unconditionally on each chef-client wake. The build system restarts chef-client daemons on all 15 nodes finally (we need this step because of pull Chef nature). The current process has a number of drawbacks we want to address. First off, it is asynchronous because the deployment script does not check chef-client logs after restart so we don't even know if the deployment was successful. It does not even wait for Chef clients to complete the cycle. Second, we definitely do not want to force chef-client restarts on all nodes because we usually deploy only a small number of packages. And third, I am not quite sure using chef-client for deployment is legitimate, probably we are just doing it wrong from the start. Please share your thoughts/experience.

  Read the article

• Generic/Text Printer on Windows 7 not prompting for file name

  - by Trevor Tippins

  Hope someone can shed some light on this. I am downloading reports from an AIX-based system by directing them to a TT printer which the terminal emulator (MultiView 2000) intercepts and directs to the default printer on the local system. This local printer is configured as a vanilla Generic/Text printer attached to a FILE port. When I print from AIX, the output is spooled down and the local printer prompts for a file name into which to save the file...but not under Windows 7. This has worked fine for many years, on both Win2K and WinXP. However, on Windows 7 the output gets spooled as a file into spool\PRINTERS (and looks as expected) but the print job then hangs with a status of "Error - Printing" and never prompts for a file name. I have to cancel the job. The Generic/Text printer works as expected with other applications. I have tried setting the printer to print directly rather than spooling but this only serves to hang the terminal session too. I've also tried to run the emulator in Windows 2000 Compatibility Mode and as Administrator in case it was something like that but with no luck. As you might expect, it does work fine in XP Mode (as long as I print to a printer defined therein and not the host's printer) but operationally this isn't going to be an option. Obviously this emulation software is a decade old (at least) and I could just cross/upgrade all the users (at a cost) but, before I do so, has anyone seen this sort of behaviour before and found some sort of fix? Remote OS: AIX 5 Client OS: Windows 7 Pro (32-bit) Printer: Generic/Text on a FILE port TE Software: MultiView 2000 (32-bit) Thanks in advance.

  Read the article

• Apache httpd: Send error logs to syslog and local disk? Without touching /etc/syslog.conf?

  - by Stefan Lasiewski

  I have an Apache httpd 2.2 server. I want to log all messages using syslog, so that the requests are sent to our central syslog server. I also want to ensure that all log messages are sent to local disk, so that a sysadmin can have easy access to the log files on the local system. It is easy to send HTTP access logs to both the local disk and to syslog. One common method is: LogFormat "%V %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined CustomLog logs/access_log combined CustomLog "|/usr/bin/logger -t httpd -i -p local4.info" combined But it is not easy to do this for error logs. The following configuration doesn't work, because the error logs only use the last ErrorLog stanza. The first ErrorLog stanza is ignored. ErrorLog logs/error_log ErrorLog syslog:local4.error How can I ensure that Apache errors logs are written to the local disk and are sent to syslog? Is it possible to do this without touching /etc/syslog.conf ? I am fine if my users want to manage their own Apache configuration files, but I do not want them touching system files such as /etc/syslog.conf

  Read the article

• Skip new Windows 7 user selection and go to login prompt

  - by Doltknuckle

  We've begun our migration to windows 7 and we ran into an interesting issue. When we hit "CTRL+ALT+DEL" we are brought to the "User selection Screen". Normally, this screen will have an icon for every local user for the machine. These machines are Domain members with "Fast User Switch" disabled so no user names are listed only the "Other User" option. If you click "Other User" or hit enter, the system moves on to the normal login screen where it prompts for user name and password. Here's the issue: We want to find a way to skip over the part where a user selects "Other User". We essentially want the system to always assume that we always want "Other User" and to go directly to the login screen when a user hits "CTRL+ALT+DEL". What I find odd is that the "Other User" doesn't show up until we've had more than one domain user log in. Right after we re-image the machine, the login process goes directly to the user credential prompt. Anyone have any ideas?

  Read the article

• Ubuntu network card problem.

  - by Steve Greene

  Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

  Read the article

• why does the partition start on sector 2048 instead of 63

  - by gcb

  I had two drives partitioned the same and running 2 raid partitions on each. One died and I replaced it under warranty for the same model. While trying to partition it, the first partition can only start on sector 2048, instead of 63 that was before. Driver have different geometry as previous and remaining ones. (Fewer heads/more cylinders) old drive: $ sudo fdisk -c -u -l /dev/sdb Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000aa189 Device Boot Start End Blocks Id System /dev/sdb1 * 63 174080339 87040138+ 83 Linux /dev/sdb2 174080340 182482334 4200997+ 82 Linux swap / Solaris /dev/sdb3 182482335 3907024064 1862270865 fd Linux raid autodetect remanufactured drive received from warranty: $ sudo fdisk -c -u -l /dev/sda Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 81 heads, 63 sectors/track, 765633 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d0b5d Device Boot Start End Blocks Id System /dev/sda1 2048 ... why is that?

  Read the article

• Windows XP Loading Problem

  - by Sadeq Dousti

  Sometimes, my Windows XP does not load correctly. It shows the login screen, and when I click my username, it load the desktop background, but the Explorer does not show up. So, I cannot see the icons on the desktop, the start menu, etc. If I press Ctrl+Alt+Del to show Task Manager, I can run programs (like media player or browser) from File--New Task (Run...). Also, in the Task Manager, I see Explorer.exe running. I tried to kill and re-run it, but nothing happens. I used Sysinternals Process Explorer to see if there were any odd process or odd behavior, but nothing was fishy. After several restarts, the system finally worked as expected. But this is not permanent: Sometimes, when I restart the system, it works just as described above (Explorer does not show up). But sometimes it works normally. I used Kaspersky to search for viruses, but nothing showed up. I think the info presented above is not enough to pinpoint the problem. Yet you might be able to tell me about a tool or something, which I can use to give you more info, or even solve the problem. PS: I can easily use the Safe Mode. It does not seem to suffer from this problem. Hence, I suspect there's some process (service) for which Explorer is waiting, but that process runs into trouble (say a race ondition, or an infinite loop) and so Explorer stalls as well.

  Read the article

• Exchange 2010 OWA- Open Other User Mailbox

  - by Benjamin Jones

  I just started working for this small firm (30 people) a little bit ago, replacing their System Admin. First thing I noticed was Exchange Server 2010 was WAY out of date. Believe it or not they did not have SP1 installed. So after I installed and configured Exchange 2010 SP3 and redirected OWA I noticed something in OWA. I could add ANYONE's User Mailbox WITHOUT giving mailbox premission. I created a couple test users, same thing. I even had another employee provide me access to their OWA and they could open anyone's Inbox without granting permission. I don't want to play the blame game, but I was SHOCKED that this was going on. Luckly being such a small company I'll be able to cover this mistake that I did not create, BUT HOW? My guess is that I need to find out where the past System Admin went wrong in providing Full Access Permission? Or could this be a Auto-Mapping issue? I found this article: http://technet.microsoft.com/en-us/library/hh529943.aspx This might work $FixAutoMapping = Get-MailboxPermission sharedmailbox |where {$_.AccessRights -eq "FullAccess" -and $_.IsInherited -eq $false} $FixAutoMapping | Remove-MailboxPermission $FixAutoMapping | ForEach {Add-MailboxPermission -Identity $_.Identity -User $_.User -AccessRights:FullAccess -AutoMapping $false} However how do I insert the above code into Powershell? Again I was thrown into this mess and I'm just trying to iron out this tangled mess.

  Read the article

• VirtualBox: using physical partition as virtual drive

  - by Hamman Samuel

  Background: I am using VirtualBox installed on Windows 7. From within VirtualBox I am using Xubuntu as a virtual OS. The reason I chose this approach is so that I don't have to keep turning off Windows and rebooting from Xubuntu every time I needed to switch OSes. And VirtualBox's seamless mode is pretty amazing to allow me see Xubuntu and Windows 7 all in one screen. Issue: Now I am thinking of a way to have Xubuntu more integrated into my system. By this I mean I want to have a physical partition for Xubuntu. But I want to still have the feeling of the seamless mode. Question: So finally, my question is: is it possible to load a partition in VirtualBox as a virtual OS? Case examples: Ideal scenario would be: I physically boot up and login to Windows 7. Now I want to access Xubuntu, so I load VirtualBox and access my Xubuntu partition without rebooting. And the other way around too, i.e. I boot up the system, login to Xubuntu, and can access the actual Windows 7 partition through VirtualBox. Other info: Please note that I am not talking about getting access to files, as I have a completely separate partition for my files, and am very familiar with VirtualBox's Shared Folders option.

  Read the article

• "iostat" command different in two equal machines

  - by Oz.

  We have several machines on Amazon (ec2) of the type c1.xlarge with 8 cpus, running the Amazon AMI. Details on the machine: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge One out of the several machines is showing a high load average, since we have run the last yum upgrade a couple of weeks a go. We did not yet update the other machines, and everything looks normal on them. The strange thing is that the top command not showing any hint for the cause of the load. CPUs are - 4.8%us, 1.1%sy, 0.0%ni, 94.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st. Mem is about 1.5GB free. Any idea what could it be, or where else can we check? iostat command on the proper machine: avg-cpu: %user %nice %system %iowait %steal %idle 8.97 0.03 4.46 0.19 0.14 86.23 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.60 0.69 55.38 587620 47254184 xvdfp2 2.64 1.10 61.04 934786 52091056 xvdfp4 0.86 0.19 41.72 163866 35601920 xvdfp1 4.37 36.59 73.89 31220810 63051504 xvdfp3 8.03 7.08 94.63 6045402 80749184 iostat command on problematic machine: avg-cpu: %user %nice %system %iowait %steal %idle 9.29 0.04 5.55 0.26 0.11 84.74 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.13 3.34 68.85 246244 5077888 xvdfp1 7.60 74.31 104.88 5480362 7734840 xvdfp3 13.22 73.67 125.00 5433386 9218600 xvdfp4 1.11 0.76 65.08 55762 4799248 xvdfp2 4.16 3.31 99.17 243818 7313264 Many thanks for the help.

  Read the article

• Best way to build / implement a corporate developer Linux distro with multiple kernels?

  - by Garen

  At work we have Linux users who understandably prefer using Ubuntu. Problem is, we also have developer tools that only work with 'officially' supported Linux distributions that use much older 2.6.18 based kernels. (And even if they worked with newer ones, the vendors could always say they won't "support" the software unless it's on one of their 'officially' supported platforms.) We could of course just tell them to use CentOS or something else 2.6.18-based, and I'm sure their response would be something like: "you can take Ubuntu from our cold, dead hands." :) Which brings to me some questions--is there any good/easy/recommended way to run something like Ubuntu as a host VM and Centos 5.x as a guest OS (with which system--Xen,KVM,VMWare, ...?), and then roll that into our own custom internal distribution that could be easily installed? KVM looks like a good high-performance option just recently included in RHEL 5.4, but if hardware support for virtualization like Intel-VT or AMD-V is necessary, then I'd guess only those folks with fairly new PCs will be able to do it. Would be very interested to hear how anyone else has addressed this kind issue. EDIT: The target audience / users of this kind of system would be developers, each one needs to run locally licensed commercial software, so building out some separate beefy central machines isn't an option unfortunately due to license restrictions. Even if that weren't the case, a couple developers could quickly eat up the resources with parallel builds. :) Ideally, I was hoping there was some step-by-step guide out there to build your own pre-built distribution that had e.g. CentOS 5.x and Ubuntu Desktop as a guest.

  Read the article

• Linux usd disk just create sg device

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata).

  Read the article

• Adding subnet to a vsphere with single vcenter and esxi host

  - by Ilya Rakhlin

  Let me start of by saying that I do not specialize in networking, I am in the process of adding additional VMs to a testing environment and wanted some recommendations. In this case I am running a single ESXI 5.1 host and a single Vcenter management server. The problem is, I need another range of IP addresses added to the existing setup; hopefully without reconfiguring everything. Currently the esxi host is configured to IP: 192.168.100.200, gateway: 192.168.100.1 and subnet: 255.255.255.0. All of the VMs are running some version of linux with hard coded IP addresses in that range, and using that subnet. The VMs I am about to deploy I want to be on the 192.168.101.X network. Is it possible to add an additional subnet to this existing system that will also communicate with the current subnet? The esxi host has 6 physical NICs but only one connected as it is only a testing system; not sure if that matters. Are there any other ways to accomplish this hopefully without restarting or at least reconfiguring the IP addresses for each VM? Reason: Due to the configuration of the VMs to run the applications that we need I am using a large amount of the current IPs in the potential range (mostly VIPs). I will be setting up a new version of this “environment” while keeping the old one, thus potentially running out of IP addresses.

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• How can I setup a Proxy I can sniff traffic from using an ESX vswitch in promiscuous mode?

  - by sandroid

  I have a pretty specific requirement, detailed below. Here's what I'm not looking for help for, to keep things tidy and on topic: How to configure a standard proxy Any ESX setup required to facilitate traffic sniffing How to sniff traffic Any changes in design (my scope limits me) I need to setup a test environment for a network-sniffing based HTTP app monitoring tool, and I need to troubleshoot a client issue but he only has a prod network, so making changes to the config on client's system "just to try" is costly. The goal here is to create a similar system in my lab, and hit the client's webapp and redirect my traffic - using a proxy - into the lab environment. The reason I want to use a proxy is so that only this specific traffic is redirected for all to see, and not all my web traffic (like my visits to serverfault :P). Everything will run inside an ESX 4.1 machine. In there, there is a traffic collection vswitch in promiscuous mode that is not on the local network for security reasons. The VM containing our listening agent is connected to this vswitch. On the same ESX host, I will setup a basic linux server and install a proxy (either apache + mod_proxy or squid, doesn't matter). I'm looking for ideas on how to deploy this for my needs so I can then figure out how to set it up accordingly. Some ideas I've had were to setup two proxies, and have them talk to eachother through this vswitch in promiscuous mode, but it seems like alot of work. Another idea is a dual-homed proxy, but I've never seen/done that before so I'm not sure how doable it is for what I'd like. I am OK with setting up a second vswitch in promiscuous mode to facilitate this if need be, but I cannot put the vswitch on the lan (which is used so my browser would communicate with the proxy) in promiscuous mode. Any ideas are welcome.

  Read the article

• certutil -ping fails with 30 seconds timeout - what to do?

  - by mark

  Dear ladies and sirs. The certificate store on my Win7 box is constantly hanging. Observe: C:\1.cmd C:\certutil -? | findstr /i ping -ping -- Ping Active Directory Certificate Services Request interface -pingadmin -- Ping Active Directory Certificate Services Admin interface C:\set PROMPT=$P($t)$G C:\(13:04:28.57)certutil -ping CertUtil: -ping command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. C:\(13:04:58.68)certutil -pingadmin CertUtil: -pingadmin command FAILED: 0x80070002 (WIN32: 2) CertUtil: The system cannot find the file specified. C:\(13:05:28.79)set PROMPT=$P$G C:\ Explanations: The first command shows you that there are –ping and –pingadmin parameters to certutil Trying any ping parameter fails with 30 seconds timeout (the current time is seen in the prompt) This is a serious problem. It screws all the secure communication in my app. If anyone knows how this can be fixed - please share. Thanks. P.S. 1.cmd is simply a batch of these commands: certutil -? | findstr /i ping set PROMPT=$P($t)$G certutil -ping certutil -pingadmin set PROMPT=$P$G

  Read the article

• How to import a text file into powershell and email it, formatted as HTML

  - by Don

  I'm trying to get a list of all Exchange accounts, format them in descending order from largest mailbox and put that data into an email in HTML format to email to myself. So far I can get the data, push it to a text file as well as create an email and send to myself. I just can't seem to get it all put together. I've been trying to use ConvertTo-Html but it just seems to return data via email like "pageFooterEntry" and "Microsoft.PowerShell.Commands.Internal.Format.AutosizeInfo" versus the actual data. I can get it to send me the right data if i don't tell it to ConvertTo-Html, just have it pipe the data to a text file and pull from it, but it's all ran together with no formatting. I don't need to save the file, i'd just like to run the command, get the data, put it in HTML and mail it to myself. Here's what I have currently: #Connects to Database and returns information on all users, organized by Total Item Size, User $body = Get-MailboxStatistics -database "Mailbox Database 0846468905" | where {$_.ObjectClass -eq “Mailbox”} | Sort-Object TotalItemSize -Descending | ft @{label=”User”;expression={$_.DisplayName}},@{label=”Total Size (MB)”;expression={$_.TotalItemSize.Value.ToMB()}} -auto | ConvertTo-Html #Pause for 5 seconds for Exchange write-host -foregroundcolor Green "Pausing for 5 seconds for Exchange" Start-Sleep -s 5 $toemail = "[email protected]" # Emails report to this address. $fromemail = "[email protected]" #Emails from this address. $server = "Exchange.company.com" #Exchange server - SMTP. #Email the report. $email = New-Object System.Net.Mail.MailMessage $email.IsBodyHtml = $True $email.To.Add($toemail) $email.From = $fromemail $email.Subject = "Exchange Mailbox Sizes" $email.Body = $body $client = New-Object System.Net.Mail.SmtpClient $server $client.UseDefaultCredentials = $true $client.Send($email) Any thoughts would be helpful, thanks!

  Read the article

• Why would e-mail from our own domain not be forwarded to gmail

  - by netboffin

  To solve a problem with spam on our server we tried to forward e-mail from our dedicated server's mailserver(matrix smtp service) to gmail, but while most e-mails got through e-mail from our own domain all went missing. They weren't in the inbox or spam or anywhere else. We've had to go back to using the old system, which means my boss gets a huge amount of spam. We have a windows 2003 server with iis 6 and the matrix smtp service installed. I've toyed with the idea of installing a mail proxy like ASSP but it looks pretty complicated. We're hosting 20 domains on the server as well as our own which has an online shop whose payment system depends on email. I can't start playing around with complicated solutions when it could have disastrous consequences and I don't know enough to implement them safely. So my question has two parts: Part One: Why can't we forward e-mails from people using the same domain. If our domain was foobar.com then [email protected] can't receive from [email protected], but he can receive from everyone else. Part Two: Is there a really simple server side solution to spam that would work with matrix? For instance popfile?

  Read the article

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• How can I change the binding order of network adapters in Windows 7?

  - by Chris Farmer

  The end goal here is that I am trying to install an Oracle 10g server on my Windows 7 x64 dev box. I use DHCP, and the Oracle installer is throwing up this warning: Checking Network Configuration requirements ... Check complete. The overall result of this check is: Failed <<<< Problem: The install has detected that the primary IP address of the system is DHCP-assigned. Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system. See the Installation Guide for more details on installing the software on systems configured with DHCP. I have installed the loopback adapter, but I am not sure how to make it the primary network adapter. I see this Microsoft KB article on the subject but it's Windows XP-oriented, and I can't seem to find a comparable one for Windows 7. Some of the options it talks about don't seem to be present in the views of the adapters that I see. So, how can I make the loopback adapter become the primary adapter?

  Read the article

• kde dropping keyboard

  - by shabbychef

  I am having problems with KDE 'dropping' my keyboard. It happens periodically when using my gentoo box directly, but has become much worse when accessing via NX (from a Mac laptop). Some possibly irrelevant clues: it appears to happen more often when the system is under higher CPU load the mouse continues to work, but no windows will accept any kind of keyboard focus. kwin will not accept tabbing between windows. when working on the machine directly, I can ctrl-alt-F1 to get to a shell (obviously this does nothing over NX). so I think it is KDE and not xorg. am running kwin-4.3.5-r1, and KDE-4.3.5 generally. this problem definitely appeared after upgrading to kde-4.x, but I do not remember if it appeared in kde-4.2. sometimes the keyboard will reappear, but sometimes I have to kill my kde session. playing with accessibility options or window-focus-stealing options in system-settings under kde will often make the keyboard responsive again, only to drop it perhaps minutes later. I had read online this might be an evdev problem under X (again, I think this is KDE, not X, but will try anything). as a result, I have fiddled with my xorg.conf endlessly. I even deleted it entirely and let nvidia-xconfig have a stab at it, with no luck I am tearing my hair out over this. I have done emerge -e xorg-server and am right now doing emerge -e kwin, to rebuild all packages that might be relevant. no luck with the xorg-server rebuild. any help appreciated. thanks,

  Read the article

• Graphics Artifacts/ Texture Flickering

  - by Cerin

  Hey I been having some problems with artifacts in games. Sometimes textures flicker. Artifacts of various shapes and sizes show up usually after a couple games of dota 2. I built my computer almost exactly one month ago and it has been doing this pretty much from the start except before the artifacts I believe just flashed on screen fast enough to where I couldn't tell what it was but I still noticed. In dota I've seen green triangular artifacts among other things. I've tried running Furmark for a while but even though it pushes the gpu much harder than dota 2, there are still no artifacts. It maxes in furmark at about 60C and running every game I've tried on it at 40C. CPU and system temp don't usually get higher than 40C either. These are my system specs: Gigabyte Z68 Intel Motherboard 16 GB Gskill Ripjaws SDRAM DDR3 Sapphire Radeon HD 7770 GHz edition Intel Core i5-2500k (with built in gpu) Corsair 750 Watt PSU windows 7-64 bit I have the latest drivers for everything. What should I do about this? Try to RMA my graphics card? Are there other things that could be causing this?

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  Hiya, I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Can't mount Linux usd disk. It just create /dev/sg device but no /dev/sd

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata).

  Read the article

< Previous Page | 788 789 790 791 792 793 794 795 796 797 798 799  | Next Page >