Search Results

Search found 501 results on 21 pages for 'alexander farber'.

Page 8/21 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15 | Next Page >

Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

- by Alexander

I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

Read the article
Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

- by Alexander

I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

Read the article
Cannot Send Item error in Outlook - permissions to registry?

- by Tim Alexander

The issue I am trying to solve is to do with users getting a Cannot Send Item error in Outlook 2007 connecting to Exchange 2007. Basically if there is an image in the email (either one they have pasted in or one from another email in the chain) they get a "Cannot Send Item" error. Initially thought it was a citrix issue but users get it when they RDP to a server as well. Changing the message to Rich Text works 80% of the time but I do not think this is a solution but more of a temporary workaround. After some troubleshooting we found that the error can be fixed by adding the user as a member of the local power users group. of course this is not really a fix. My thoughts were that the ability of a power user to add/remove software may give them more access to the registry which might allow them to get round a restriction that is in place for a normal user. I have tried going through a procmon but the wealth of information is confusing. It initially looked like it may be an Outlook 2007 email security setting but this does not change between power user and normal user (set to 1 in the registry, "Use the security setting from Outlook Security Settings Public Folders"). I am struggling to fine tune my troubleshooting to work out exactly what is blocking it. Has anyone had an experience with an error similar to this? Or are there any tips for trying to track down issues via procmon as I must admit my approach seems somewhat lacking :) EDIT: So I have trawled through the two logs we have from process monitor (one as a power user and one a normal user). annoyingly I can find no obvious difference where something is denied access. There are more access denied events in the normal user log but these are quickly followed by sucessful entries to the same path fractions of a second later. The only thing that does stand out is an access denied to HKCR.html. This does not even appear in the power user version of the log. From what I understand this helps determine the default browser which ties in nicely with the fact that 9 out of 10 times you can send the message as Rich Text. EDIT: Looks like KB2509470 was causing the issue. Not really sure why but when I can work out what it does and why it causes the problem will post here unless anyone beats me to it!

Read the article
Would NetBSD be a good choice for a web server?

- by Alexander

I've the choice of crafting a NetBSD image for a Xen VPS host, and was just wanting to play around as I like BSD and wished to use it for my general web hosting. I will be hosting a low-mid traffic website and maybe a few other simple services. Do you think NetBSD would be a sufficient choice, in terms of general performance of multiple system users and fair amount of traffic to Apache compared to what Linux could normally handle? I am concerned if I do start to really like it and keep it, I may be limiting myself if I am to move further with my web host and get more traffic (and maybe a lot of FTP access and user shell accounts) Ken

Read the article
Is ECC mandatory in SSD technology?

- by Alexander Shcheblikin

While shopping for an SSD I have noticed that some manufacturers promote their "Pro" models as the ones sporting ECC data protection. Those manufacturers do not mention ECC in their budget models descriptions. However, Wikipedia article on flash memory states that "NAND relies on ECC to compensate for bits that may spontaneously fail during normal device operation." So the question is does any SSD device use ECC behind the scenes for its normal operation and is that ECC "feature" just a marketing ploy?

Read the article
Creating a custom NAS compatible with the Mac Time machine and for media streaming

- by Bobby Alexander

I am planning to assemble a custom NAS machine using an Intel Atom processor. I need the NAS for the following purposes: It should be accessible from by Windows PC so that I can dump data on the NAS (installations, media etc) It should be accessible from my Macbook for the above use. I should be able to use it with the Mac time machine software for backup. The media should be available to my PS3 for streaming. I should be able to access it from my iphone. All the above features should be available over wireless. The time machine feature is very important. Is this even possible? Can someone provide resources on how I can assemble such a machine and setup the required software on it? Much appreciated.

Read the article
XP can't read data from transferred HD

- by Alexander Miller

Computer A, running XP, died. XP was installed on a fresh HD in computer B. Slaved data-backup HD from A was installed as slave on B. B will not read it; shows only 2 folders, Recycler and System Volume Info. All of these are older machines with IDE drives. What's going on & how can I read/transfer the data from the transferred drive? This was only a trial run. Actually I will need to transfer the master HD from A - which has XP on it - and read from its data partition because (blush) the backup drive was not up to date.

Read the article
Juniper router dropping pings to external interface

- by Alexander Garden

My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

Read the article
Disable "Send as XPS Attachment" Word 2007

- by Tim Alexander

Is there a way to disable this option either via Group Policy or via some form of registry hack? Normally I would go down the route of telling users not to send as XPS and send as something else but with our recent upgrade to 2007 lots of users are banding these files around. Unfortunately our version of Citrix does not play nicely with XPS documents and we end up having to log them out. Am told the fix for Citrix is not forthcoming so wondered if I could bury my head in the sand and disable the option all together. Regards Tim

Read the article
What version of Ubuntu to use for Desktop with 8Gb RAM?

- by Alexander

This may sound as a stupid question, but I am really interested whether Ubuntu Desktop i386 will be able to use all my available RAM. I want to use the latest, non-LTS version, 10.10. It says on the website that it's (i386) the Recommended version. I also recall that Flash Player had issues with 64 bit Linux. Also, the 64 bit version is listed in the Universal USB Installer as amd64. Does this mean that it's using instruction sets specific to AMD CPUs? (I have an Intel) Will it work fine with Intel? So which one to download and install? What to do to be able to use 8Gb of RAM?

Read the article
Make logwatch reports more interesting?

- by Alexander Shcheblikin

Is it possible to improve the quality of reports from logwatch? Like make it not just report disk usage which doesn't even change much in daily operation, but report significant changes in usage or approaching critical capacity levels? If I cannot do that with logwatch and instead have to write custom scripts to produce such reports, logwatch appears to be pretty useless, or even dangerous, as many users reportedly grow to ignore emails from it knowing they are so boring.

Read the article
Why am I seeing Zero errors in non-ECC RAM?

- by Alexander Shcheblikin

According to sources, memory errors are a very probable event: Some say the probability of a DRAM error is 95% in just 3 days of operation of a computer with just 4 GB of RAM, others say 32% of servers experience at least one error in a month with 8% of DIMMs being at fault. Contrary to those horrors, in my more than 10 years of personal computers use I have seen exactly none of the memory errors. I admit I never paid special attention to the subject. However, I have ventured multi-hour memtest86 runs couple of times and never seen an error either. Some of the factors that IMO should aggravate the memory problems: I build my computers out of the most "bulk commodity" parts: mainstream budget motherboards and the next to cheapest memory. also I usually max out the technology available, e.g. in the times of 32 bit OS'es I used 4 GB of RAM and with the current desktop CPUs and the newer 64 bit OS'es I use 32 GB of RAM. memory usage is moderately heavy with lots of virtual machines up running small and big tasks 24/7/365. But nevertheless, no memory-related problems ever found! How's that?

Read the article
linux migration/N high cpu consumption

- by Alexander

on my linux appliance based on 3.0.0-14 kernel I got: RPN:/tmp# ps axuf | grep migration root 6 92.9 0.0 0 0 ? S Apr23 2788:33 \_ [migration/0] root 7 99.7 0.0 0 0 ? S Apr23 2993:20 \_ [migration/1] my top is RPN:/tmp# top -b -n1 top - 12:03:41 up 2 days, 2:18, 5 users, load average: 25.76, 25.26, 24.73 Tasks: 171 total, 1 running, 168 sleeping, 0 stopped, 2 zombie Cpu(s): 14.0%us, 12.6%sy, 0.8%ni, 72.0%id, 0.3%wa, 0.0%hi, 0.3%si, 0.0%st Mem: 1543032k total, 1264728k used, 278304k free, 25308k buffers Swap: 0k total, 0k used, 0k free, 183168k cached My question: why processes "migration/N" take so much CPU?

Read the article
How to route packets from Wi-Fi to Ethernet on OSX?

- by Alexander Artemenko

I have a trouble, configuring a home network. Here is how my devices are connected together: Internet ? Wi-Fi Router ? MacBook ? iMac ?ethernet cable? Synology NAS I have no ability to plugin NAS right into the Wi-Fi router. The problem is that MacBook does not see NAS, because they are in different networks — I configured Wi-Fi Router to serve 192.168.10.0/24 addresses, and configured iMac's ethernet connection to use 192.168.20/24 network. Is there a way to setup route from MacBook to the NAS?

Read the article
How does Notepad++ know to recognize the HTML and CSS in PHP files? Can I do this with PSP files?

- by Andrew Alexander

I am trying to get Notepad++ to recognize PSP (Python Server Pages) files. I've got it to recognize Python (by adding PSP to the ext= section), however it doesn't seem to understand that Python is only within the <% %> and <%= %> sections. I want it to parse HTML, CSS, Javascript and possibly even PHP (though if I am using PSP, I'd probably stick with that) as well, showing all the colors, etc, that would normally be associated with it. How do I go about that?

Read the article
Video Chat going through a server

- by Alexander

I'm trying to build a simple video chat client on the mac as a little project and I want it to be able to go over my own little server and arrive at the other end (so going over the internet rather just locally). So my question is if there are any references I should look for online on how to handle something like this on the server side and such. Any links or pointers would be a great help, thanks!

Read the article
Extract first page from multiple pdfs

- by Tim Alexander

Have got about 500 PDFs to go through and extract the first page of. They then need to go through some time consuming conversion process so was hoping to try and save some time by have a batch process to extract just the first page from the 500 pdfs and place it in a new pdf. Have had a poke around Acrobat but can find no real method of doing this for multiple files. Does anyone know any other programs or methods that this could be achieved? Free and open source are obviously more favourable :) EDIT: Have actually had some success using GhostScript to extract just one page. Am now looking at how to batch that and take the list of files and use those.

Read the article
Finding default gateway in an openvpn environment in windows

- by Alexander Trümper

I need to find the default gateway in a openvpn scenario where the route output looks like that: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 0.0.0.0 128.0.0.0 10.8.0.1 10.8.0.2 30 So I googled around a bit and a found this script here: @For /f "tokens=3" %%* in ( 'route.exe print ^|findstr "\<0.0.0.0\>"' ) Do @Set "DefaultGateway=%%*" echo %DefaultGateway% This works, but matches both lines in the route output. But I need to find this line: 0.0.0.0 0.0.0.0 10.49.73.1 10.49.73.24 10 So I tried to modify the findstr parameter like this: findstr "\<0.0.0.0\>.\<0.0.0.0\>" in the expectation that '.' will match for the tab between the columns. But it doesn't. It will still set DefaultGateway to 10.8.0.1 I couldn't find a clue in MS documentation either. Maybe someone knows the right expression? Thanks a lot.

Read the article
Secure copy uucp style

- by Alexander Janssen

I often have the case that I have to make a lot of hops to the remote host, just because there is no direct routing between my client and the remote host. When I need to copy files from a remote host two or more hops away, I always have to: client$ ssh host1 host1$ ssh host2 host2$ scp host3:/myfile . host2$ exit host1$ scp host2:myfile . host1$ exit client$ scp host1:myfile . Back when uucp still was being used this would be as simple as a uucp host1!host2!host3 /myfile . I know that there's uucp over ssh, but unfortunately I don't have the proper privileges on those machines to set it up. Also, I'm not sure if I really want to fiddle around with customer's machines. Does anyone know of a method doing this tasks without the need to setup a lot of tunnels or deploying new software to remote hosts? Maybe some kind of recursive script which clones itself to all the remote hosts, doing the hard work for me? Assume that authentication takes place with public keys and that all hosts do SSH Agent Forwarding. Edit: I'm not looking for a way to automatically forwarding my interactive sesssion to the nexthop host. I want a solution to copy files bangpath-style using scp via multiple hops without the need to install uucp on any of those machines. I don't have the (legal) rights or the privileges to make permanent changes to the ssh-config. Also, I'm sharing this username and hosts with a lot of other people. I'm willing to hack up my own script, but I wanted to know if anyone knows something which already does it. Minimum-invasive changes to hosts on the bangpath, simple invocation from the client. Edit 2: To give you an impression of how it's properly been done in interactive sessions, have a look at the GXPC clustershell. This is basically a Python-script, which spwans itself over to all remote hosts which have connectivity and where your ssh-key is installed. The great thing about it is, that you can tell "I can reach HostC via HostB via HostA." It just works. I want to have this for scp.

Read the article
Crossplatform "jail" for an application

- by Alexander

We currently have a variety of systems (Linux, Solarix, *BSD, HP-UX ...) on which we are not allowed to install anything into / (but I have root access. That's strange, I know). But we'd like to run Puppet on all of them. So, the obvious idea is to install Puppet with all prebuilt dependencies into some isolated tree, something like "jail", which will allow to use dependences from some prefix and to access the host system. The big advatanges would be uniform deployment and updates. One solution that came to my mind is to deploy Gentoo Prefix, and install Puppet there with package manager. However, this requires a lot of extra space and some manual patching for each system. Maybe there are some more elegant and simple solutions?

Read the article
Update Windows XP to SP3 without internet

- by Alexander

I've been asked to update some computers running Windows XP (without any service packs) to Windows XP SP3. The computers don't have an internet connection (only a small intranet) and have never been updated since first install. Do I need to install SP1a first, then SP2, then SP3, or can I install SP3 immediately? And where do I find the right files, that don't require an internet connection during installation? All help is welcome. Thanks!

Read the article
Notify user of message arrival in another mailbox

- by Tim Alexander

This is very similar to this question but has a few differences. Basically we have a user dealing with a conflict of interest case. To separate the mail from prying eyes (and the draconian routing system we have in place) the user has been granted access to a second conflicts mailbox that is only accessible to him via OWA. This has worked fine for years but now the user would like a notification to be sent to him when a message arrives in his conflicts mailbox. Initially I thought an Outlook rule would work but of course the client is never logged in so the Outlook rules are never processed. This led me to think that an Exchange Transport rule might work but the only options I can see are to Forward or Copy the message to another user. this would bypass the conflicts setup. All I really need is a notification and not the actual message to be sent. Is this at all possible with Exchange 2007? Or if not is there any thirdparty addition or workaround that anyone has come across?

Read the article
Large scale file replication with an option to "unsubscribe" from a replicated file on a given machine

- by Alexander Gladysh

I have a 100+ GB files per day incoming on one machine. (File size is arbitrary and can be adjusted as needed.) I have several other machines that do some work on these files. I need to reliably deliver each incoming file to the worker machines. A worker machine should be able to free its HDD from a file once it is done working with it. It is preferable that a file would be uploaded to the worker only once and then processed in place, and then deleted, without copying somewhere else — to minimize already high HDD load. (Worker itself requires quite a bit of bandwidth.) Please advise a solution that is not based on Java. None of existing replication solutions that I've seen can do the "free HDD from the file once processed" stuff — but maybe I'm missing something... A preferable solution should work with files (from the POV of our business logic code), not require the business logic to connect to some queue or other. (Internally the solution may use whatever technology it needs to — except Java.)

Read the article
YUI Compressor java

- by Alexander

Hi I want to use Yahoo's compressor for compressing js and css files. Which can be found here: http://developer.yahoo.com/yui/compressor/ My only problem is that i have never used Java before. I have no idea how to execute or use this command line. I only have experience with js, jquery and php. It simply says: Usage: java -jar yuicompressor-x.y.z.jar [options] [input file] How should I proceed?

Read the article
Cannot connect Windows 7 PCs to a Windows 2011 SBS domain

- by Alexander Miles

I can connect XP machines just fine to our new domain, however, I get the following error when I try to bind any Windows 7 box on our network to the 2011 SBS domain: An attempt to resolve the DNS name of a DC in the domain being joined has failed. Please verify this client is configured to reach a DNS server that can resolve DNS names in the target domain. I am wondering if part of the problem might be related to the fact we still have our Win2k DC active (and running DNS) until this server is set up for good? Any help on this would be much appreciated.

Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15 | Next Page >