Search Results

Search found 1157 results on 47 pages for 'latency'.

Page 8/47 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• Intel PRO/1000 Server NIC on Windows latency. How to measure?

  - by Bobb

  Please note - this question is about latency of the card itself. Not latency of internet or anything else. Thank you for your attention on this matter. It is often said that good server NIC does make difference compared to low grade cards and on-board Ethernet chips. I understand that on-board chip will likely consume CPU time and stand-alone card would use its own chip. Also server card would be faster than low-grade card. Are these 2 facts explaining most of the server cards advantages over on-board and low-grade cards ethernet? How would you measure latency on the card itself? I saw some reports stating some microseconds figures of NIC latency but I dont see how to measure that... Any advise will be appreciated.

  Read the article

• Filemaker XSL 20sec Query Latency

  - by Ian Wetherbee

  I have an ASP frontend that loads data from a Filemaker database using XSL to perform simple queries. The problem is that the first page load takes 20 seconds +/- 200ms, then the next few page refreshes within a minute of the first request take <200ms, then the cycle starts over again. Each page load makes only 2 XSL queries, and they execute fast after the first page load, so what is causing the delay on the first page load? I have caching turned up with a 100% hit rate, and number of connections at 100. I've tried with XSL database sessions on and off, and session time anywhere from 1 to 60 minutes without any changes. The XSL loads from ASP use a GET request and add a Basic Authorization header to authenticate each time. During fast page requests, the fmserver.exe and fmswpc.exe processes don't even flinch, but during a 20 second holdup I see fmserver jump to 30% CPU and a 3mb I/O read a few seconds into the request, and occasionally fmswpc jump to 60% CPU.

  Read the article

• Gmail zend imap - latency when fetching messageids

  - by T.B Ygg

  i have this code to fetch emails from gmail using imap with the zend framework. i go back 2 days in my search (as i do not want all messages) all works well but it takes forever to load the messages and i need to do this for 5+ users, it seems like the search goes through the entire gmail message archive in getting the newest ones. my code looks like this: $dato = date('j-F-Y', strtotime($Date. ' - 2 days')); $dato = "SINCE ".$dato; $messageids = $imap->search(array($dato)); any ideas on how to make zend work faster?

  Read the article

• Gradient boosting predictions in low-latency production environments?

  - by lockedoff

  Can anyone recommend a strategy for making predictions using a gradient boosting model in the <10-15ms range (the faster the better)? I have been using R's gbm package, but the first prediction takes ~50ms (subsequent vectorized predictions average to 1ms, so there appears to be overhead, perhaps in the call to the C++ library). As a guideline, there will be ~10-50 inputs and ~50-500 trees. The task is classification and I need access to predicted probabilities. I know there are a lot of libraries out there, but I've had little luck finding information even on rough prediction times for them. The training will happen offline, so only predictions need to be fast -- also, predictions may come from a piece of code / library that is completely separate from whatever does the training (as long as there is a common format for representing the trees).

  Read the article

• How can i get latency when using Game Center?

  - by Freddy

  I'm pretty new to network programming. Basically I'm using game center for making a relatively simple iPhone game using Game-center p2p. However i'm now working on a algorithm to improve the multiplayer performance. But, I need to know how long it took for a package to travel from one device to the another device (latency) for the algorithm to work good. As for now, I have solved the problem by sending a double with time interval since 1970 in the package and then I compare it with the time at the other device. However I have heard that the NSDate methods is connected to the internet, which also will cause latency so the time interval would not be perfectly correct. What is the ideal way to check for how long it take for a package to be sent?

  Read the article

• How do i mount my SD Card? I am using ubuntu 10.04

  - by shobhit

  root@shobhit:/media# lsusb Bus 002 Device 017: ID 14cd:125c Super Top Bus 002 Device 003: ID 0c45:6421 Microdia Bus 002 Device 002: ID 8087:0020 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 011: ID 413c:8160 Dell Computer Corp. Bus 001 Device 006: ID 413c:8162 Dell Computer Corp. Bus 001 Device 005: ID 413c:8161 Dell Computer Corp. Bus 001 Device 004: ID 138a:0008 DigitalPersona, Inc Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) Bus 001 Device 002: ID 8087:0020 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lspci -v -nn 00:1a.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fbc08000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1d.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 06) (prog-if 20) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at fbc07000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCIe advanced features <?> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev a6) (prog-if 01) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=20, subordinate=20, sec-latency=32 Capabilities: [50] Subsystem: Dell Device [1028:0441] 00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller [8086:3b0b] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information <?> Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b2f] (rev 06) (prog-if 01) Subsystem: Dell Device [1028:0441] Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 29 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at fbc06000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+ Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA <?> Capabilities: [b0] PCIe advanced features <?> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 06) Subsystem: Dell Device [1028:0441] Flags: medium devsel, IRQ 3 Memory at fbc05000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 00:1f.6 Signal processing controller [1180]: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem [8086:3b32] (rev 06) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 3 Memory at fbc04000 (64-bit, non-prefetchable) [size=4K] Capabilities: [50] Power Management version 3 Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- 12:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:4727] (rev 01) Subsystem: Dell Device [1028:0010] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fbb00000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number cb-c0-8b-ff-ff-38-00-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl 13:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03) Subsystem: Dell Device [1028:0441] Flags: bus master, fast devsel, latency 0, IRQ 28 I/O ports at e000 [size=256] Memory at d0b04000 (64-bit, prefetchable) [size=4K] Memory at d0b00000 (64-bit, prefetchable) [size=16K] Expansion ROM at fba00000 [disabled] [size=128K] Capabilities: [40] Power Management version 3 Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4 Capabilities: [cc] Vital Product Data <?> Capabilities: [100] Advanced Error Reporting <?> Capabilities: [140] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-e0-4c-68-00-00-00-03 Kernel driver in use: r8169 Kernel modules: r8169 root@shobhit:/home/shobhit/scripts/internalUtilities# sudo lshw shobhit description: Portable Computer product: Vostro 3500 vendor: Dell Inc. version: A10 serial: FV1L3N1 width: 32 bits capabilities: smbios-2.6 dmi-2.6 smp-1.4 smp configuration: boot=normal chassis=portable cpus=2 uuid=44454C4C-5600-1031-804C-C6C04F334E31 *-core description: Motherboard product: 0G2R51 vendor: Dell Inc. physical id: 0 version: A10 serial: .FV1L3N1.CN7016612H00PW. slot: To Be Filled By O.E.M. *-cpu:0 description: CPU product: Intel(R) Core(TM) i5 CPU M 480 @ 2.67GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 slot: CPU 1 size: 1197MHz capacity: 2926MHz width: 64 bits clock: 533MHz capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx rdtscp x86-64 constant_tsc arch_perfmon pebs bts xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida arat tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: id=4 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: internal write-back unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 512KiB capacity: 512KiB capabilities: internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 3MiB capacity: 3MiB capabilities: internal varies unified *-logicalcpu:0 description: Logical CPU physical id: 4.1 width: 64 bits capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 width: 64 bits capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 width: 64 bits capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 width: 64 bits capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 width: 64 bits capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 width: 64 bits capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 width: 64 bits capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 width: 64 bits capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 width: 64 bits capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a width: 64 bits capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b width: 64 bits capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c width: 64 bits capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d width: 64 bits capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e width: 64 bits capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f width: 64 bits capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 width: 64 bits capabilities: logical *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 3GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT112S6TFR8C-H9 vendor: AD80 physical id: 0 serial: 5525C935 slot: DIMM_A size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: HMT125S6TFR8C-H9 vendor: AD80 physical id: 1 serial: 3441D6CA slot: DIMM_B size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A10 (10/25/2010) size: 64KiB capacity: 1984KiB capabilities: mca pci upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb zipboot biosbootspecification *-cpu:1 physical id: 1 bus info: cpu@1 version: 6.5.5 serial: 0002-0655-0000-0000-0000-0000 size: 1197MHz capacity: 1197MHz capabilities: vmx ht cpufreq configuration: id=4 *-logicalcpu:0 description: Logical CPU physical id: 4.1 capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 4.2 capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 4.3 capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 4.4 capabilities: logical *-logicalcpu:4 description: Logical CPU physical id: 4.5 capabilities: logical *-logicalcpu:5 description: Logical CPU physical id: 4.6 capabilities: logical *-logicalcpu:6 description: Logical CPU physical id: 4.7 capabilities: logical *-logicalcpu:7 description: Logical CPU physical id: 4.8 capabilities: logical *-logicalcpu:8 description: Logical CPU physical id: 4.9 capabilities: logical *-logicalcpu:9 description: Logical CPU physical id: 4.a capabilities: logical *-logicalcpu:10 description: Logical CPU physical id: 4.b capabilities: logical *-logicalcpu:11 description: Logical CPU physical id: 4.c capabilities: logical *-logicalcpu:12 description: Logical CPU physical id: 4.d capabilities: logical *-logicalcpu:13 description: Logical CPU physical id: 4.e capabilities: logical *-logicalcpu:14 description: Logical CPU physical id: 4.f capabilities: logical *-logicalcpu:15 description: Logical CPU physical id: 4.10 capabilities: logical *-pci description: Host bridge product: Core Processor DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 18 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-display description: VGA compatible controller product: Core Processor Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 18 width: 64 bits clock: 33MHz capabilities: msi pm bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:30 memory:fac00000-faffffff memory:c0000000-cfffffff(prefetchable) ioport:f080(size=8) *-communication UNCLAIMED description: Communication controller product: 5 Series/3400 Series Chipset HECI Controller vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc09000-fbc0900f *-usb:0 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:fbc08000-fbc083ff *-multimedia description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:22 memory:fbc00000-fbc03fff *-pci:0 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:24 ioport:2000(size=4096) memory:bc000000-bc1fffff memory:bc200000-bc3fffff(prefetchable) *-pci:1 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:25 ioport:3000(size=4096) memory:fbb00000-fbbfffff memory:bc400000-bc5fffff(prefetchable) *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:8b:aa:d8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=10.0.1.50 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbb00000-fbb03fff *-pci:2 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 3 vendor: Intel Corporation physical id: 1c.2 bus info: pci@0000:00:1c.2 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:26 ioport:e000(size=4096) memory:fba00000-fbafffff ioport:d0b00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 03 serial: 78:2b:cb:cc:0e:2a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:28 ioport:e000(size=256) memory:d0b04000-d0b04fff(prefetchable) memory:d0b00000-d0b03fff(prefetchable) memory:fba00000-fba1ffff(prefetchable) *-pci:3 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: 06 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm bus_master cap_list configuration: driver=pcieport resources: irq:27 ioport:d000(size=4096) memory:fb000000-fb9fffff ioport:d0000000(size=10485760) *-usb:1 description: USB Controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 06 width: 32 bits clock: 33MHz capabilities: pm debug bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:fbc07000-fbc073ff *-pci:4 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: a6 width: 32 bits clock: 33MHz capabilities: pci bus_master cap_list *-isa description: ISA bridge product: Mobile 5 Series Chipset LPC Interface Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 06 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 5 Series/3400 Series Chipset 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi1 version: 06 width: 32 bits clock: 66MHz capabilities: storage msi pm bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:29 ioport:f070(size=8) ioport:f060(size=4) ioport:f050(size=8) ioport:f040(size=4) ioport:f020(size=32) memory:fbc06000-fbc067ff *-disk description: ATA Disk product: WDC WD3200BEKT-7 vendor: Western Digital physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WX21AC0W1945 size: 298GiB (320GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=77e3ed41 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: aa69-51c0 size: 98MiB capacity: 100MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2012-04-03 02:00:15 filesystem=ntfs label=System Reserved state=clean *-volume:1 description: Windows NTFS volume physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 version: 3.1 serial: 9854ff5c-1dea-a147-84a6-624e758f44b8 size: 48GiB capacity: 48GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-10 13:55:31 filesystem=ntfs modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:2 description: Extended partition physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 size: 48GiB capacity: 48GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 1952MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 46GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,barrier=1,data=ordered state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/56AA8094AA807273 version: 3.1 serial: 22a29e8d-56c7-9a4a-adea-528103948f6d size: 200GiB capacity: 200GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2012-04-02 20:17:15 filesystem=ntfs modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-cdrom description: DVD-RAM writer product: DVD+-RW TS-L633J vendor: TSSTcorp physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 version: D200 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 5 Series/3400 Series Chipset SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 06 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:fbc05000-fbc050ff ioport:f000(size=32) *-generic UNCLAIMED description: Signal processing controller product: 5 Series/3400 Series Chipset Thermal Subsystem vendor: Intel Corporation physical id: 1f.6 bus info: pci@0000:00:1f.6 version: 06 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: latency=0 resources: memory:fbc04000-fbc04fff *-scsi physical id: 2 bus info: usb@2:1.1 logical name: scsi15 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk description: SCSI Disk physical id: 0.0.0 bus info: scsi@15:0.0.0 logical name: /dev/sdb I have tried all options like fdisk /dev/sdb , pmount /dev/sdb but nothing is working .Pls guide me

  Read the article

• NEC uPD720200 USB 3.0 not working on Ubuntu 12.04

  - by Jagged

  I've recently installed Ubuntu 12.04 64-bit on a HP Envy 15 1104tx. Most stuff appears to be working fine with the exception of the two USB3 ports (USB2 port works fine). I've read a lot of articles but so far have not been able to find a solution. I've tried adding 'pci=nomsi' to '/etc/default/grub' but this made no difference. Some articles suggest booting into Windows and upgrading the firmware on the uPD720200. Any body had any experience of this? Is there a way I can checked the firmware version of the NEC uPD720200 in Linux to see if there is an update available? Any help appreciated. uname -a: Linux HP-ENVY-15-1104tx 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lshw: hp-envy-15-1104tx description: Notebook product: HP ENVY 15 Notebook PC (WF591PA#ABG) vendor: Hewlett-Packard version: 0492110000241910001420000 serial: CNF0301C79 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=notebook family=103C_5335KV sku=WF591PA#ABG uuid=434E4630-3330-3143-3739-60EB6906688F *-core description: Motherboard product: 1522 vendor: Hewlett-Packard physical id: 0 version: 36.35 serial: CNF0301C79 slot: Base Board Chassis Location *-firmware description: BIOS vendor: Hewlett-Packard physical id: 0 version: F.2B date: 10/12/2010 size: 1MiB capacity: 1472KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppynec int13floppytoshiba int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int9keyboard int10video acpi usb biosbootspecification *-memory description: System Memory physical id: 13 slot: System board or motherboard size: 16GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 0 serial: E13C4316 slot: Bottom size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 1 serial: E03C3E16 slot: Bottom size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 2 serial: 672279CC slot: On Board size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 3 serial: 652286CC slot: On Board size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-cpu description: CPU product: Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz vendor: Intel Corp. physical id: 1d bus info: cpu@0 version: Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz slot: CPU size: 1199MHz capacity: 1199MHz width: 64 bits clock: 1066MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=4 threads=8 *-cache:0 description: L3 cache physical id: 1e slot: L3 Cache size: 8MiB capacity: 8MiB capabilities: synchronous internal write-through unified *-cache:1 description: L2 cache physical id: 20 slot: L2 Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through unified *-cache:2 description: L1 cache physical id: 21 slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through instruction *-cache description: L1 cache physical id: 1f slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through data *-pci:0 description: Host bridge product: Core Processor DMI vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 11 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Core Processor PCI Express Root Port 1 vendor: Intel Corporation physical id: 3 bus info: pci@0000:00:03.0 version: 11 width: 32 bits clock: 33MHz capabilities: pci msi pciexpress pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 ioport:4000(size=4096) memory:d4100000-d41fffff ioport:c0000000(size=268435456) *-display description: VGA compatible controller product: Broadway PRO [Mobility Radeon HD 5800 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:58 memory:c0000000-cfffffff memory:d4100000-d411ffff ioport:4000(size=256) memory:d4140000-d415ffff *-multimedia description: Audio device product: Juniper HDMI Audio [Radeon HD 5700 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:56 memory:d4120000-d4123fff *-pci:1 description: PCI bridge product: Core Processor PCI Express Root Port 3 vendor: Intel Corporation physical id: 5 bus info: pci@0000:00:05.0 version: 11 width: 32 bits clock: 33MHz capabilities: pci msi pciexpress pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:d4000000-d40fffff *-usb description: USB controller product: uPD720200 USB 3.0 Host Controller vendor: NEC Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:16 memory:d4000000-d4001fff *-generic:0 UNCLAIMED description: System peripheral product: Core Processor System Management Registers vendor: Intel Corporation physical id: 8 bus info: pci@0000:00:08.0 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:1 UNCLAIMED description: System peripheral product: Core Processor Semaphore and Scratchpad Registers vendor: Intel Corporation physical id: 8.1 bus info: pci@0000:00:08.1 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:2 UNCLAIMED description: System peripheral product: Core Processor System Control and Status Registers vendor: Intel Corporation physical id: 8.2 bus info: pci@0000:00:08.2 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:3 UNCLAIMED description: System peripheral product: Core Processor Miscellaneous Registers vendor: Intel Corporation physical id: 8.3 bus info: pci@0000:00:08.3 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-generic:4 UNCLAIMED description: System peripheral product: Core Processor QPI Link vendor: Intel Corporation physical id: 10 bus info: pci@0000:00:10.0 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-generic:5 UNCLAIMED description: System peripheral product: Core Processor QPI Routing and Protocol Registers vendor: Intel Corporation physical id: 10.1 bus info: pci@0000:00:10.1 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-multimedia description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:55 memory:d4200000-d4203fff *-pci:2 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 05 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 ioport:3000(size=4096) memory:d3000000-d3ffffff ioport:d0000000(size=16777216) *-network description: Wireless interface product: Centrino Advanced-N 6200 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 35 serial: 00:27:10:40:e4:68 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=9.221.4.1 build 25532 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:54 memory:d3000000-d3001fff *-pci:3 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 05 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 ioport:2000(size=4096) memory:d2000000-d2ffffff ioport:d1000000(size=16777216) *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 60:eb:69:06:68:8f size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=10.161.0.147 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:57 memory:d2000000-d203ffff ioport:2000(size=128) *-usb description: USB controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:20 memory:d4205800-d4205bff *-pci:4 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: a5 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list *-isa description: ISA bridge product: Mobile 5 Series Chipset LPC Interface Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: RAID bus controller product: 82801 Mobile SATA Controller [RAID mode] vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:45 ioport:5048(size=8) ioport:5054(size=4) ioport:5040(size=8) ioport:5050(size=4) ioport:5020(size=32) memory:d4205000-d42057ff *-disk description: ATA Disk product: OCZ-VERTEX3 physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 2.15 serial: OCZ-0350P6H316X5KUQE size: 223GiB (240GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000592dd *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: e741f18c-cfc5-4bce-b1e7-f80e517a3a22 size: 207GiB capacity: 207GiB capabilities: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-06-15 06:49:27 filesystem=ext4 lastmountpoint=/ modified=2012-06-14 21:23:42 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,barrier=1,data=ordered mounted=2012-07-10 16:18:20 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 15GiB capacity: 15GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 15GiB capabilities: nofs *-serial UNCLAIMED description: SMBus product: 5 Series/3400 Series Chipset SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:d4205c00-d4205cff ioport:5000(size=32) *-pci:1 description: Host bridge product: Core Processor QuickPath Architecture Generic Non-Core Registers vendor: Intel Corporation physical id: 101 bus info: pci@0000:ff:00.0 version: 04 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: Core Processor QuickPath Architecture System Address Decoder vendor: Intel Corporation physical id: 102 bus info: pci@0000:ff:00.1 version: 04 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: Core Processor QPI Link 0 vendor: Intel Corporation physical id: 103 bus info: pci@0000:ff:02.0 version: 04 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: Core Processor QPI Physical 0 vendor: Intel Corporation physical id: 104 bus info: pci@0000:ff:02.1 version: 04 width: 32 bits clock: 33MHz *-pci:5 description: Host bridge product: Core Processor Integrated Memory Controller vendor: Intel Corporation physical id: 105 bus info: pci@0000:ff:03.0 version: 04 width: 32 bits clock: 33MHz *-pci:6 description: Host bridge product: Core Processor Integrated Memory Controller Target Address Decoder vendor: Intel Corporation physical id: 106 bus info: pci@0000:ff:03.1 version: 04 width: 32 bits clock: 33MHz *-pci:7 description: Host bridge product: Core Processor Integrated Memory Controller Test Registers vendor: Intel Corporation physical id: 107 bus info: pci@0000:ff:03.4 version: 04 width: 32 bits clock: 33MHz *-pci:8 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Control Registers vendor: Intel Corporation physical id: 108 bus info: pci@0000:ff:04.0 version: 04 width: 32 bits clock: 33MHz *-pci:9 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Address Registers vendor: Intel Corporation physical id: 109 bus info: pci@0000:ff:04.1 version: 04 width: 32 bits clock: 33MHz *-pci:10 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Rank Registers vendor: Intel Corporation physical id: 10a bus info: pci@0000:ff:04.2 version: 04 width: 32 bits clock: 33MHz *-pci:11 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers vendor: Intel Corporation physical id: 10b bus info: pci@0000:ff:04.3 version: 04 width: 32 bits clock: 33MHz *-pci:12 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Control Registers vendor: Intel Corporation physical id: 10c bus info: pci@0000:ff:05.0 version: 04 width: 32 bits clock: 33MHz *-pci:13 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Address Registers vendor: Intel Corporation physical id: 10d bus info: pci@0000:ff:05.1 version: 04 width: 32 bits clock: 33MHz *-pci:14 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Rank Registers vendor: Intel Corporation physical id: 10e bus info: pci@0000:ff:05.2 version: 04 width: 32 bits clock: 33MHz *-pci:15 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers vendor: Intel Corporation physical id: 10f bus info: pci@0000:ff:05.3 version: 04 width: 32 bits clock: 33MHz *-battery description: Lithium Ion Battery product: NK06053 vendor: SMP-ATL24 physical id: 1 slot: Primary capacity: 4800mWh configuration: voltage=11.1V lspci: 02:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Hewlett-Packard Company Device 1522 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d4000000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd lsusb (with thumb drive plugged into USB3 port): Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 5986:01d0 Acer, Inc Bus 001 Device 004: ID 03f0:231d Hewlett-Packard

  Read the article

• SQL IO and SAN troubles

  - by James

  We are running two servers with identical software setup but different hardware. The first one is a VM on VMWare on a normal tower server with dual core xeons, 16 GB RAM and a 7200 RPM drive. The second one is a VM on XenServer on a powerful brand new rack server, with 4 core xeons and shared storage. We are running Dynamics AX 2012 and SQL Server 2008 R2. When I insert 15 000 records into a table on the slow tower server (as a test), it does so in 13 seconds. On the fast server it takes 33 seconds. I re-ran these tests several times with the same results. I have a feeling it is some sort of IO bottleneck, so I ran SQLIO on both. Here are the results for the slow tower server: C:\Program Files (x86)\SQLIO>test.bat C:\Program Files (x86)\SQLIO>sqlio -kW -t8 -s120 -o8 -frandom -b8 -BH -LS C:\Tes tFile.dat sqlio v1.5.SG using system counter for latency timings, 14318180 counts per second 8 threads writing for 120 secs to file C:\TestFile.dat using 8KB random IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: C:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 226.97 MBs/sec: 1.77 latency metrics: Min_Latency(ms): 0 Avg_Latency(ms): 281 Max_Latency(ms): 467 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 99 C:\Program Files (x86)\SQLIO>sqlio -kR -t8 -s120 -o8 -frandom -b8 -BH -LS C:\Tes tFile.dat sqlio v1.5.SG using system counter for latency timings, 14318180 counts per second 8 threads reading for 120 secs from file C:\TestFile.dat using 8KB random IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: C:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 91.34 MBs/sec: 0.71 latency metrics: Min_Latency(ms): 14 Avg_Latency(ms): 699 Max_Latency(ms): 1124 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 100 C:\Program Files (x86)\SQLIO>sqlio -kW -t8 -s120 -o8 -fsequential -b64 -BH -LS C :\TestFile.dat sqlio v1.5.SG using system counter for latency timings, 14318180 counts per second 8 threads writing for 120 secs to file C:\TestFile.dat using 64KB sequential IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: C:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 1094.50 MBs/sec: 68.40 latency metrics: Min_Latency(ms): 0 Avg_Latency(ms): 58 Max_Latency(ms): 467 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 100 C:\Program Files (x86)\SQLIO>sqlio -kR -t8 -s120 -o8 -fsequential -b64 -BH -LS C :\TestFile.dat sqlio v1.5.SG using system counter for latency timings, 14318180 counts per second 8 threads reading for 120 secs from file C:\TestFile.dat using 64KB sequential IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: C:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 1155.31 MBs/sec: 72.20 latency metrics: Min_Latency(ms): 17 Avg_Latency(ms): 55 Max_Latency(ms): 205 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 100 Here are the results of the fast rack server: C:\Program Files (x86)\SQLIO>test.bat C:\Program Files (x86)\SQLIO>sqlio -kW -t8 -s120 -o8 -frandom -b8 -BH -LS E:\Tes tFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads writing for 120 secs to file E:\TestFile.dat using 8KB random IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) open_file: CreateFile (E:\TestFile.dat for write): The system cannot find the pa th specified. exiting C:\Program Files (x86)\SQLIO>sqlio -kR -t8 -s120 -o8 -frandom -b8 -BH -LS E:\Tes tFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads reading for 120 secs from file E:\TestFile.dat using 8KB random IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) open_file: CreateFile (E:\TestFile.dat for read): The system cannot find the pat h specified. exiting C:\Program Files (x86)\SQLIO>sqlio -kW -t8 -s120 -o8 -fsequential -b64 -BH -LS E :\TestFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads writing for 120 secs to file E:\TestFile.dat using 64KB sequential IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) open_file: CreateFile (E:\TestFile.dat for write): The system cannot find the pa th specified. exiting C:\Program Files (x86)\SQLIO>sqlio -kR -t8 -s120 -o8 -fsequential -b64 -BH -LS E :\TestFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads reading for 120 secs from file E:\TestFile.dat using 64KB sequential IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) open_file: CreateFile (E:\TestFile.dat for read): The system cannot find the pat h specified. exiting C:\Program Files (x86)\SQLIO>test.bat C:\Program Files (x86)\SQLIO>sqlio -kW -t8 -s120 -o8 -frandom -b8 -BH -LS c:\Tes tFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads writing for 120 secs to file c:\TestFile.dat using 8KB random IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: c:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 2575.77 MBs/sec: 20.12 latency metrics: Min_Latency(ms): 1 Avg_Latency(ms): 24 Max_Latency(ms): 655 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 5 8 9 9 9 8 5 3 1 1 1 1 0 0 0 0 0 0 0 0 0 37 C:\Program Files (x86)\SQLIO>sqlio -kR -t8 -s120 -o8 -frandom -b8 -BH -LS c:\Tes tFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads reading for 120 secs from file c:\TestFile.dat using 8KB random IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: c:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 1141.39 MBs/sec: 8.91 latency metrics: Min_Latency(ms): 1 Avg_Latency(ms): 55 Max_Latency(ms): 652 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 91 C:\Program Files (x86)\SQLIO>sqlio -kW -t8 -s120 -o8 -fsequential -b64 -BH -LS c :\TestFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads writing for 120 secs to file c:\TestFile.dat using 64KB sequential IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: c:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 341.37 MBs/sec: 21.33 latency metrics: Min_Latency(ms): 5 Avg_Latency(ms): 186 Max_Latency(ms): 120037 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 100 C:\Program Files (x86)\SQLIO>sqlio -kR -t8 -s120 -o8 -fsequential -b64 -BH -LS c :\TestFile.dat sqlio v1.5.SG using system counter for latency timings, 62500000 counts per second 8 threads reading for 120 secs from file c:\TestFile.dat using 64KB sequential IOs enabling multiple I/Os per thread with 8 outstanding buffering set to use hardware disk cache (but not file cache) using current size: 5120 MB for file: c:\TestFile.dat initialization done CUMULATIVE DATA: throughput metrics: IOs/sec: 1024.07 MBs/sec: 64.00 latency metrics: Min_Latency(ms): 5 Avg_Latency(ms): 61 Max_Latency(ms): 81632 histogram: ms: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24+ %: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 100 Three of the four tests are, to my mind, within reasonable parameters for the rack server. However, the 64 write test is incredibly slow on the rack server. (68 mb/sec on the slow tower vs 21 mb/s on the rack). The read speed for 64k also seems slow. Is this enough to say there is some sort of bottleneck with the shared storage? I need to know if I can take this evidence and say we need to launch an investigation into this. Any help is appreciated.

  Read the article

• Log response-time in restlet-based webservice

  - by amarillion

  What is the simplest way to log the response-time for a restlet-based webservice? I want to make sure that our webservice has a reasonable response time. So I want to be able to keep an eye on response times, and do something about the requests that take too long. The closest thing I could find is this recipe: http://www.naviquan.com/blog/restlet-cookbook-log, it explains how to change the log format. But there doesn't seem to be a parameter for response times, so probably a completely different approach is needed.

  Read the article

• How do you determine an acceptable response time for DB requests?

  - by qiq

  According to this discussion of Google App Engine on Hacker News, A DB (read) request takes over 100ms on the datastore. That's insane and unusable for about 90% of applications. How do you determine what is an acceptable response time for a DB read request? I have been using App Engine without noticing any issues with DB responsiveness. But, on the other hand, I'm not sure I would even know what to look for in that regard :)

  Read the article

• data path (travel) of tcp data from "write" syscall downto I/O registers programming

  - by osgx

  Hello Is there a good overview of tcp data path in Linux (2.6, not 2.4 if the path actually differ)? Where is a packet on different stages of tcp/ip stack handling? How packet is packed to tcp segment, then ip packet. How it is transmitted to network card? (with series of I/O regs write and DMA?) Is it transmitted to network card in the "write" syscall handler (with some deep callstack) or is it transmitted at some other moment?

  Read the article

• 16 millisecond quantization when sending/receivingtcp packets

  - by MKZ

  Hi, I have a C++ application running on windows xp 32 system sending and receiving short tcp/ip packets. Measuring (accurately) the arrival time I see a quantization of the arrival time to 16 millisecond time units. (Meaning all packets arriving are at (16 )xN milliseconds separated from each other) To avoid packet aggregation I tried to disable the NAGLE algorithm by setting the IPPROTO_TCP option to TCP_NODELAY in the socket variables but it did not help I suspect that the problem is related to the windows schedular which also have a 16 millisecond clock.. Any idea of a solution to this problem ? Thanks

  Read the article

• Microphone not capturing sound on 12.04 Lenovo G580

  - by Yam Marcovic

  In both Skype and the Sound Recorder application, I am not capturing any audio from my built-in microphone. I'm not sure why. Otherwise, sound output is working well. I have tried running gstreamer-properties and setting the Default Input plugin to PulseAUdio as well (to match the output), and it didn't help. I have tried running alsamixer -V all and I only get 2 input-related entries: Capture(L R) which is on 100 and not muted (can't be either), and Analog Mic Boost which is on 20db. Extra info: Camera (video) is working well on Skype and Kamerka. Can you please help me get my microphone to work? lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 3000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) (prog-if 30 [XHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 41 Region 0: Memory at e0600000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 43 Region 0: Memory at e0614000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at e0619000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 44 Region 0: Memory at e0610000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: e0500000-e05fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Memory behind bridge: e0400000-e04fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Lenovo Device 3977 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at e0618000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 40 Region 0: I/O ports at 3088 [size=8] Region 1: I/O ports at 3094 [size=4] Region 2: I/O ports at 3080 [size=8] Region 3: I/O ports at 3090 [size=4] Region 4: I/O ports at 3060 [size=32] Region 5: Memory at e0617000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) Subsystem: Lenovo Device 3977 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 10 Region 0: Memory at e0615000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 3040 [size=32] Kernel modules: i2c-i801 01:00.0 Ethernet controller: Atheros Communications Inc. AR8162 Fast Ethernet (rev 08) Subsystem: Lenovo Device 3979 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0500000 (64-bit, non-prefetchable) [size=256K] Region 2: I/O ports at 2000 [size=128] Capabilities: <access denied> 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: Lenovo Device 31a1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at e0400000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath9k Kernel modules: ath9k aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: CONEXANT Analog [CONEXANT Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0

  Read the article

• Acer aspire 5735z wireless not working after upgrade to 11.10

  - by Jon

  I cant get my wifi card to work at all after upgrading to 11.10 Oneiric. I'm not sure where to start to fix this. Ive tried using the additional drivers tool but this shows that no additional drivers are needed. Before my upgrade I had a drivers working for the Rt2860 chipset. Any help on this would be much appreciated.... thanks Jon jon@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:72:ec:76:d5 inet addr:192.168.1.134 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:72ff:feec:76d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7846 errors:0 dropped:0 overruns:0 frame:0 TX packets:7213 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8046624 (8.0 MB) TX bytes:1329442 (1.3 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:91 errors:0 dropped:0 overruns:0 frame:0 TX packets:91 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34497 (34.4 KB) TX bytes:34497 (34.4 KB) Ive included by dmesg output below [ 0.428818] NET: Registered protocol family 2 [ 0.429003] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.430562] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.436614] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.437409] TCP: Hash tables configured (established 524288 bind 65536) [ 0.437412] TCP reno registered [ 0.437431] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437482] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437678] NET: Registered protocol family 1 [ 0.437705] pci 0000:00:02.0: Boot video device [ 0.437892] PCI: CLS 64 bytes, default 64 [ 0.437916] Simple Boot Flag at 0x57 set to 0x1 [ 0.438294] audit: initializing netlink socket (disabled) [ 0.438309] type=2000 audit(1319243447.432:1): initialized [ 0.440763] Freeing initrd memory: 13416k freed [ 0.468362] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.488192] VFS: Disk quotas dquot_6.5.2 [ 0.488254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.488888] fuse init (API version 7.16) [ 0.488985] msgmni has been set to 5890 [ 0.489381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.489413] io scheduler noop registered [ 0.489415] io scheduler deadline registered [ 0.489460] io scheduler cfq registered (default) [ 0.489583] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.489633] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 0.489699] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.489741] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 0.489800] pcieport 0000:00:1c.2: setting latency timer to 64 [ 0.489841] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X [ 0.489904] pcieport 0000:00:1c.3: setting latency timer to 64 [ 0.489944] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X [ 0.490006] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.490047] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X [ 0.490126] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.490149] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.490196] intel_idle: MWAIT substates: 0x1110 [ 0.490198] intel_idle: does not run on family 6 model 15 [ 0.491240] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.493473] ACPI: AC Adapter [ADP1] (on-line) [ 0.493590] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 0.496771] ACPI: Lid Switch [LID0] [ 0.496818] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 0.496823] ACPI: Sleep Button [SLPB] [ 0.496865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 0.496869] ACPI: Power Button [PWRF] [ 0.496900] ACPI: acpi_idle registered with cpuidle [ 0.498719] Monitor-Mwait will be used to enter C-1 state [ 0.498753] Monitor-Mwait will be used to enter C-2 state [ 0.498761] Marking TSC unstable due to TSC halts in idle [ 0.517627] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.517630] ACPI: Thermal Zone [TZS0] (67 C) [ 0.524796] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.524799] ACPI: Thermal Zone [TZS1] (67 C) [ 0.524823] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.524852] ERST: Table is not found! [ 0.524948] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.680991] ACPI: Battery Slot [BAT0] (battery present) [ 0.688567] Linux agpgart interface v0.103 [ 0.688672] agpgart-intel 0000:00:00.0: Intel GM45 Chipset [ 0.688865] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 0.689786] agpgart-intel 0000:00:00.0: detected 65536K stolen memory [ 0.689912] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.691006] brd: module loaded [ 0.691510] loop: module loaded [ 0.691967] Fixed MDIO Bus: probed [ 0.691990] PPP generic driver version 2.4.2 [ 0.692065] tun: Universal TUN/TAP device driver, 1.6 [ 0.692067] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.692146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.692181] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.692206] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.692210] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.692255] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.692289] ehci_hcd 0000:00:1a.7: debug port 1 [ 0.696181] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 0.696202] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf8904800 [ 0.712014] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.712131] hub 1-0:1.0: USB hub found [ 0.712136] hub 1-0:1.0: 6 ports detected [ 0.712230] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.712243] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.712247] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.712287] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.712315] ehci_hcd 0000:00:1d.7: debug port 1 [ 0.716201] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 0.716216] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8904c00 [ 0.732014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.732130] hub 2-0:1.0: USB hub found [ 0.732135] hub 2-0:1.0: 6 ports detected [ 0.732209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.732223] uhci_hcd: USB Universal Host Controller Interface driver [ 0.732254] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.732262] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.732265] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.732298] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.732325] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820 [ 0.732441] hub 3-0:1.0: USB hub found [ 0.732445] hub 3-0:1.0: 2 ports detected [ 0.732508] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 0.732514] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.732518] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.732553] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.732577] uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001840 [ 0.732696] hub 4-0:1.0: USB hub found [ 0.732700] hub 4-0:1.0: 2 ports detected [ 0.732762] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.732768] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.732772] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.732805] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.732829] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001860 [ 0.732942] hub 5-0:1.0: USB hub found [ 0.732946] hub 5-0:1.0: 2 ports detected [ 0.733007] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.733014] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.733017] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.733057] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.733082] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880 [ 0.733202] hub 6-0:1.0: USB hub found [ 0.733206] hub 6-0:1.0: 2 ports detected [ 0.733265] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.733273] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.733276] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.733313] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.733351] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018a0 [ 0.733466] hub 7-0:1.0: USB hub found [ 0.733470] hub 7-0:1.0: 2 ports detected [ 0.733532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.733539] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.733542] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.733578] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.733610] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0 [ 0.733730] hub 8-0:1.0: USB hub found [ 0.733736] hub 8-0:1.0: 2 ports detected [ 0.733843] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.751594] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.751605] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.751732] mousedev: PS/2 mouse device common for all mice [ 0.752670] rtc_cmos 00:08: RTC can wake from S4 [ 0.752770] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 0.752796] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 0.752907] device-mapper: uevent: version 1.0.3 [ 0.752976] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected] [ 0.753028] cpuidle: using governor ladder [ 0.753093] cpuidle: using governor menu [ 0.753096] EFI Variables Facility v0.08 2004-May-17 [ 0.753361] TCP cubic registered [ 0.753482] NET: Registered protocol family 10 [ 0.753966] NET: Registered protocol family 17 [ 0.753992] Registering the dns_resolver key type [ 0.754113] PM: Hibernation image not present or could not be loaded. [ 0.754131] registered taskstats version 1 [ 0.771553] Magic number: 15:152:507 [ 0.771667] rtc_cmos 00:08: setting system clock to 2011-10-22 00:30:48 UTC (1319243448) [ 0.772238] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.772240] EDD information not available. [ 0.774165] Freeing unused kernel memory: 984k freed [ 0.774504] Write protecting the kernel read-only data: 10240k [ 0.774755] Freeing unused kernel memory: 20k freed [ 0.775093] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 0.779727] Freeing unused kernel memory: 1400k freed [ 0.801946] udevd[84]: starting version 173 [ 0.880950] sky2: driver version 1.28 [ 0.881046] sky2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.881096] sky2 0000:02:00.0: setting latency timer to 64 [ 0.881197] sky2 0000:02:00.0: Yukon-2 Extreme chip revision 2 [ 0.881871] sky2 0000:02:00.0: irq 45 for MSI/MSI-X [ 0.896273] sky2 0000:02:00.0: eth0: addr 00:1d:72:ec:76:d5 [ 0.910630] ahci 0000:00:1f.2: version 3.0 [ 0.910647] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.910710] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X [ 0.910775] ahci: SSS flag set, parallel bus scan disabled [ 0.910812] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 0.910816] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs [ 0.910821] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.941773] scsi0 : ahci [ 0.941954] scsi1 : ahci [ 0.942038] scsi2 : ahci [ 0.942118] scsi3 : ahci [ 0.942196] scsi4 : ahci [ 0.942268] scsi5 : ahci [ 0.942332] ata1: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904100 irq 46 [ 0.942336] ata2: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904180 irq 46 [ 0.942339] ata3: DUMMY [ 0.942340] ata4: DUMMY [ 0.942344] ata5: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904300 irq 46 [ 0.942347] ata6: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904380 irq 46 [ 1.028061] usb 1-5: new high speed USB device number 2 using ehci_hcd [ 1.181775] usbcore: registered new interface driver uas [ 1.260062] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.261126] ata1.00: ATA-8: Hitachi HTS543225L9A300, FBEOC40C, max UDMA/133 [ 1.261129] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.262360] ata1.00: configured for UDMA/133 [ 1.262518] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54322 FBEO PQ: 0 ANSI: 5 [ 1.262716] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.262762] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 1.262824] sd 0:0:0:0: [sda] Write Protect is off [ 1.262827] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.262851] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.287277] sda: sda1 sda2 sda3 [ 1.287693] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.580059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.581188] ata2.00: ATAPI: HL-DT-STDVDRAM GT10N, 1.00, max UDMA/100 [ 1.582663] ata2.00: configured for UDMA/100 [ 1.584162] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT10N 1.00 PQ: 0 ANSI: 5 [ 1.585821] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.585824] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.585953] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.586038] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.632061] usb 6-1: new low speed USB device number 2 using uhci_hcd [ 1.908056] ata5: SATA link down (SStatus 0 SControl 300) [ 2.228065] ata6: SATA link down (SStatus 0 SControl 300) [ 2.228955] Initializing USB Mass Storage driver... [ 2.229052] usbcore: registered new interface driver usb-storage [ 2.229054] USB Mass Storage support registered. [ 2.235827] scsi6 : usb-storage 1-5:1.0 [ 2.235987] usbcore: registered new interface driver ums-realtek [ 2.244451] input: B16_b_02 USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input4 [ 2.244598] generic-usb 0003:046D:C025.0001: input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1/input0 [ 2.244620] usbcore: registered new interface driver usbhid [ 2.244622] usbhid: USB HID core driver [ 3.091083] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 3.238275] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS [ 3.348261] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.351897] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 47.138012] udevd[334]: starting version 173 [ 47.177678] lp: driver loaded but no devices found [ 47.197084] wmi: Mapper loaded [ 47.197526] acer_wmi: Acer Laptop ACPI-WMI Extras [ 47.210227] acer_wmi: Brightness must be controlled by generic video driver [ 47.566578] Disabling lock debugging due to kernel taint [ 47.584050] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 47.620666] type=1400 audit(1319239895.347:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=624 comm="apparmor_parser" [ 47.620934] type=1400 audit(1319239895.347:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=624 comm="apparmor_parser" [ 47.621108] type=1400 audit(1319239895.347:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=624 comm="apparmor_parser" [ 47.633056] [drm] Initialized drm 1.1.0 20060810 [ 47.722594] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 47.722602] i915 0000:00:02.0: setting latency timer to 64 [ 47.807152] ndiswrapper (check_nt_hdr:141): kernel is 64-bit, but Windows driver is not 64-bit;bad magic: 010B [ 47.807159] ndiswrapper (load_sys_files:206): couldn't prepare driver 'rt2860' [ 47.807930] ndiswrapper (load_wrap_driver:108): couldn't load driver rt2860; check system log for messages from 'loadndisdriver' [ 47.856250] usbcore: registered new interface driver ndiswrapper [ 47.861772] i915 0000:00:02.0: irq 47 for MSI/MSI-X [ 47.861781] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 47.861783] [drm] Driver supports precise vblank timestamp query. [ 47.861842] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 47.980620] fixme: max PWM is zero. [ 48.286153] fbcon: inteldrmfb (fb0) is primary device [ 48.287033] Console: switching to colour frame buffer device 170x48 [ 48.287062] fb0: inteldrmfb frame buffer device [ 48.287064] drm: registered panic notifier [ 48.333883] acpi device:02: registered as cooling_device2 [ 48.334053] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 48.334128] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 48.334203] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 48.334644] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334652] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334673] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 48.334737] HDA Intel 0000:00:1b.0: irq 48 for MSI/MSI-X [ 48.334772] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 48.356107] Adding 261116k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:261116k [ 48.380946] hda_codec: ALC268: BIOS auto-probing. [ 48.390242] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 48.390365] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 48.490870] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr [ 48.917990] ppdev: user-space parallel port driver [ 48.950729] type=1400 audit(1319239896.675:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=941 comm="apparmor_parser" [ 48.951114] type=1400 audit(1319239896.675:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=941 comm="apparmor_parser" [ 48.977706] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000 [ 49.048871] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 [ 49.078713] sky2 0000:02:00.0: eth0: enabling interface [ 49.079462] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 50.762266] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 50.762702] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.751478] type=1400 audit(1319239902.475:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=1039 comm="apparmor_parser" [ 54.755907] type=1400 audit(1319239902.479:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1040 comm="apparmor_parser" [ 54.756237] type=1400 audit(1319239902.483:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1040 comm="apparmor_parser" [ 54.756417] type=1400 audit(1319239902.483:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1040 comm="apparmor_parser" [ 54.764825] type=1400 audit(1319239902.491:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1041 comm="apparmor_parser" [ 54.768365] type=1400 audit(1319239902.495:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=1041 comm="apparmor_parser" [ 54.770601] type=1400 audit(1319239902.495:13): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=1041 comm="apparmor_parser" [ 54.770729] type=1400 audit(1319239902.495:14): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=1038 comm="apparmor_parser" [ 54.775181] type=1400 audit(1319239902.499:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1043 comm="apparmor_parser" [ 54.775533] type=1400 audit(1319239902.499:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1043 comm="apparmor_parser" [ 54.936691] init: failsafe main process (891) killed by TERM signal [ 54.944583] init: apport pre-start process (1096) terminated with status 1 [ 55.000373] init: apport post-stop process (1160) terminated with status 1 [ 55.005291] init: gdm main process (1159) killed by TERM signal [ 59.782579] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [ 60.992021] eth0: no IPv6 routers present [ 61.936072] device eth0 entered promiscuous mode [ 62.053949] Bluetooth: Core ver 2.16 [ 62.054005] NET: Registered protocol family 31 [ 62.054007] Bluetooth: HCI device and connection manager initialized [ 62.054010] Bluetooth: HCI socket layer initialized [ 62.054012] Bluetooth: L2CAP socket layer initialized [ 62.054993] Bluetooth: SCO socket layer initialized [ 62.058750] Bluetooth: RFCOMM TTY layer initialized [ 62.058758] Bluetooth: RFCOMM socket layer initialized [ 62.058760] Bluetooth: RFCOMM ver 1.11 [ 62.059428] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 62.059432] Bluetooth: BNEP filters: protocol multicast [ 62.460389] init: plymouth-stop pre-start process (1662) terminated with status 1 '

  Read the article

• ubuntu 10.04 logs itself out overnight

  - by Corey

  Every night when I leave work, I lock the screen via ubuntu's "power" button in the top right hand panel. When I come to work in the morning, I'm greeted with the log-in screen. This doesn't happen every night, but most. I'm running ubuntu 10.04 on a Dell inspiron. I've included some HW specs, and also dmesg output. Please let me know what other logs may be useful. thanks! Corey ~$ dmesg [20559.696062] type=1503 audit(1285957687.048:16): operation="open" pid=6212 parent=1 profile="/usr/bin/evince" requested_mask="::r" denied_mask="::r" fsuid=1000 ouid=0 name="/usr/local/lib/libltdl.so.7.2.2" [21127.951621] type=1503 audit(1285958255.300:17): operation="open" pid=6390 parent=1 profile="/usr/bin/evince" requested_mask="::r" denied_mask="::r" fsuid=1000 ouid=0 name="/usr/local/lib/libltdl.so.7.2.2" [291038.528014] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [291038.528025] render error detected, EIR: 0x00000000 [291038.528042] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 22973891 at 22973890) [291038.828014] [drm:i915_hangcheck_elapsed] *ERROR* Hangcheck timer elapsed... GPU hung [291038.828023] render error detected, EIR: 0x00000000 [291038.828042] [drm:i915_do_wait_request] *ERROR* i915_do_wait_request returns -5 (awaiting 22973894 at 22973890) ~$ lspci -vv 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 27 Region 0: Memory at fe400000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at dc00 [size=8] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at feaf8000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: 80000000-801fffff Prefetchable memory behind bridge: 0000000080200000-00000000803fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: feb00000-febfffff Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at d880 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at d800 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at d480 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d400 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) (prog-if 20) Subsystem: Dell Device 02e1 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at feaf7c00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt, intel-rng 00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at d080 [size=8] Region 1: I/O ports at d000 [size=4] Region 2: I/O ports at cc00 [size=8] Region 3: I/O ports at c880 [size=4] Region 4: I/O ports at c800 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01) Subsystem: Dell Device 02e1 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 4: I/O ports at 0400 [size=32] Kernel modules: i2c-i801 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Subsystem: Dell Device 02e1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: I/O ports at e800 [size=256] Region 2: Memory at fdfff000 (64-bit, prefetchable) [size=4K] Region 4: Memory at fdfe0000 (64-bit, prefetchable) [size=64K] Expansion ROM at febe0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 log$ tail -n 15 Xorg.0.log.old for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information. (II) Power Button: Close (II) UnloadModule: "evdev" (II) Power Button: Close (II) UnloadModule: "evdev" (II) USB Optical Mouse: Close (II) UnloadModule: "evdev" (II) Dell Dell USB Entry Keyboard: Close (II) UnloadModule: "evdev" (II) Macintosh mouse button emulation: Close (II) UnloadModule: "evdev" (II) AIGLX: Suspending AIGLX clients for VT switch ddxSigGiveUp: Closing log

  Read the article

• composite-video-to-usb adaptor

  - by sawa

  I bought a composite-video-to-usb adaptor. I want to stream video game in ubuntu. How can I do that? My environment: Monoprice USB Video and Audio Grabber Ubuntu 11.04 The relevant output of lsusb: Bus 001 Device 011: ID 0572:262a Conexant Systems (Rockwell), Inc. The relevant output of sudo lshw: *-usb:0 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #4 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:f0e0(size=32) *-usb:1 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #5 vendor: Intel Corporation physical id: 1a.1 bus info: pci@0000:00:1a.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:21 ioport:f0c0(size=32) *-usb:2 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #6 vendor: Intel Corporation physical id: 1a.2 bus info: pci@0000:00:1a.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f0a0(size=32) *-usb:3 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #2 vendor: Intel Corporation physical id: 1a.7 bus info: pci@0000:00:1a.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:18 memory:e0525c00-e0525fff *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:43 memory:e0520000-e0523fff *-usb:4 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:f080(size=32) *-usb:5 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:f060(size=32) *-usb:6 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f040(size=32) *-usb:7 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #1 vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:e0525800-e0525bff The relevant output of dmesg: [18953.220035] usb 1-1: new high speed USB device using ehci_hcd and address 6 [19964.761076] Linux video capture interface: v2.00 [19964.767112] usbcore: registered new interface driver uvcvideo [19964.767115] USB Video Class driver (v1.0.0)

  Read the article

• Garbled text in Screen [closed]

  - by Prabin Dahal

  The graphical Interface in my system is garbled with some text. At the beginning I thought it was due to java and tomcat that I installed. But after removing java and tomcat, it is still the same. I am using ubuntu server and i have installed xfce desktop environment with oboard softkey I have added my dmesg output to this message. What is the problem here. I am not able to figure it out. Thank you for your help. Prabin [ 0.390936] usbcore: registered new interface driver usbfs [ 0.391006] usbcore: registered new interface driver hub [ 0.391147] usbcore: registered new device driver usb [ 0.391580] PCI: Using ACPI for IRQ routing [ 0.400509] PCI: pci_cache_line_size set to 64 bytes [ 0.400669] reserve RAM buffer: 000000000009ec00 - 000000000009ffff [ 0.400681] reserve RAM buffer: 000000007f597000 - 000000007fffffff [ 0.400699] reserve RAM buffer: 000000007f6f0000 - 000000007fffffff [ 0.401135] NetLabel: Initializing [ 0.401155] NetLabel: domain hash size = 128 [ 0.401168] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.401212] NetLabel: unlabeled traffic allowed by default [ 0.401466] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.401494] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.401520] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.408228] Switching to clocksource hpet [ 0.434341] AppArmor: AppArmor Filesystem Enabled [ 0.434447] pnp: PnP ACPI init [ 0.434531] ACPI: bus type pnp registered [ 0.434784] pnp 00:00: [bus 00-ff] [ 0.434794] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.434804] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.434813] pnp 00:00: [io 0x0d00-0xffff window] [ 0.434822] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.434831] pnp 00:00: [mem 0x00000000 window] [ 0.434840] pnp 00:00: [mem 0x80000000-0xffffffff window] [ 0.435018] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.435526] pnp 00:01: [mem 0xe0000000-0xefffffff] [ 0.435537] pnp 00:01: [mem 0x7f700000-0x7f7fffff] [ 0.435545] pnp 00:01: [mem 0x7f800000-0x7fffffff] [ 0.435554] pnp 00:01: [mem 0xfee00000-0xfeefffff] [ 0.435727] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.435754] system 00:01: [mem 0x7f700000-0x7f7fffff] has been reserved [ 0.435775] system 00:01: [mem 0x7f800000-0x7fffffff] has been reserved [ 0.435796] system 00:01: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.435818] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.436233] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436245] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436414] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.436512] pnp 00:03: [io 0x0060] [ 0.436521] pnp 00:03: [io 0x0064] [ 0.436548] pnp 00:03: [irq 1] [ 0.436682] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.436825] pnp 00:04: [irq 12] [ 0.436958] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) [ 0.437835] pnp 00:05: [io 0x03f8-0x03ff] [ 0.437861] pnp 00:05: [irq 4] [ 0.437870] pnp 00:05: [dma 0 disabled] [ 0.438142] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439014] pnp 00:06: [io 0x02f8-0x02ff] [ 0.439036] pnp 00:06: [irq 3] [ 0.439045] pnp 00:06: [dma 0 disabled] [ 0.439297] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439346] pnp 00:07: [io 0x0000-0x000f] [ 0.439355] pnp 00:07: [io 0x0081-0x0083] [ 0.439363] pnp 00:07: [io 0x0087] [ 0.439371] pnp 00:07: [io 0x0089-0x008b] [ 0.439380] pnp 00:07: [io 0x008f] [ 0.439388] pnp 00:07: [io 0x00c0-0x00df] [ 0.439563] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.439617] pnp 00:08: [io 0x0070-0x0077] [ 0.439639] pnp 00:08: [irq 8] [ 0.439751] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.439788] pnp 00:09: [io 0x0061] [ 0.439893] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.439977] pnp 00:0a: [io 0x0010-0x001f] [ 0.439986] pnp 00:0a: [io 0x0022-0x003f] [ 0.439994] pnp 00:0a: [io 0x0044-0x005f] [ 0.440055] pnp 00:0a: [io 0x0063] [ 0.440063] pnp 00:0a: [io 0x0065] [ 0.440071] pnp 00:0a: [io 0x0067-0x006f] [ 0.440079] pnp 00:0a: [io 0x0072-0x007f] [ 0.440086] pnp 00:0a: [io 0x0080] [ 0.440094] pnp 00:0a: [io 0x0084-0x0086] [ 0.440102] pnp 00:0a: [io 0x0088] [ 0.440109] pnp 00:0a: [io 0x008c-0x008e] [ 0.440117] pnp 00:0a: [io 0x0090-0x009f] [ 0.440125] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.440133] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.440141] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.440150] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440160] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440168] pnp 00:0a: [io 0x03f4] [ 0.440175] pnp 00:0a: [io 0x03f5] [ 0.440183] pnp 00:0a: [io 0x0374] [ 0.440190] pnp 00:0a: [io 0x0375] [ 0.440405] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.440432] system 00:0a: [io 0x03f4] has been reserved [ 0.440451] system 00:0a: [io 0x03f5] has been reserved [ 0.440469] system 00:0a: [io 0x0374] has been reserved [ 0.440488] system 00:0a: [io 0x0375] has been reserved [ 0.440508] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.440550] pnp 00:0b: [io 0x00f0-0x00ff] [ 0.440572] pnp 00:0b: [irq 13] [ 0.440691] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.440770] pnp 00:0c: [io 0x0810] [ 0.440779] pnp 00:0c: [io 0x0800-0x080f] [ 0.440787] pnp 00:0c: [io 0xffff] [ 0.440947] system 00:0c: [io 0x0810] has been reserved [ 0.440970] system 00:0c: [io 0x0800-0x080f] has been reserved [ 0.440989] system 00:0c: [io 0xffff] has been reserved [ 0.441010] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.441620] pnp 00:0d: [io 0x0900-0x097f] [ 0.441630] pnp 00:0d: [io 0x09c0-0x09ff] [ 0.441639] pnp 00:0d: [io 0x0400-0x043f] [ 0.441647] pnp 00:0d: [io 0x0480-0x04bf] [ 0.441656] pnp 00:0d: [mem 0xfec00000-0xfec85fff] [ 0.441664] pnp 00:0d: [mem 0xfed1c000-0xfed1ffff] [ 0.441673] pnp 00:0d: [mem 0x000c0000-0x000dffff] [ 0.441689] pnp 00:0d: [mem 0x000e0000-0x000effff] [ 0.441697] pnp 00:0d: [mem 0x000f0000-0x000fffff] [ 0.441706] pnp 00:0d: [mem 0xff800000-0xffffffff] [ 0.441911] system 00:0d: [io 0x0900-0x097f] has been reserved [ 0.441935] system 00:0d: [io 0x09c0-0x09ff] has been reserved [ 0.441955] system 00:0d: [io 0x0400-0x043f] has been reserved [ 0.441975] system 00:0d: [io 0x0480-0x04bf] has been reserved [ 0.441997] system 00:0d: [mem 0xfec00000-0xfec85fff] could not be reserved [ 0.442019] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.442040] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved [ 0.442061] system 00:0d: [mem 0x000e0000-0x000effff] could not be reserved [ 0.442082] system 00:0d: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.442103] system 00:0d: [mem 0xff800000-0xffffffff] has been reserved [ 0.442126] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.442308] pnp 00:0e: [mem 0xfed00000-0xfed003ff] [ 0.442454] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.442569] pnp 00:0f: [mem 0x7f6f0000-0x7f6fffff] [ 0.442762] system 00:0f: [mem 0x7f6f0000-0x7f6fffff] has been reserved [ 0.442788] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.443360] pnp: PnP ACPI: found 16 devices [ 0.443378] ACPI: ACPI bus type pnp unregistered [ 0.443395] PnPBIOS: Disabled by ACPI PNP [ 0.486106] PCI: max bus depth: 3 pci_try_num: 4 [ 0.486189] pci 0000:00:1c.0: PCI bridge to [bus 01-01] [ 0.486217] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff] [ 0.486241] pci 0000:00:1c.0: bridge window [mem 0xd0100000-0xd01fffff] [ 0.486266] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff7fffff pref] [ 0.486298] pci 0000:03:01.0: PCI bridge to [bus 04-04] [ 0.486319] pci 0000:03:01.0: bridge window [io 0xd000-0xdfff] [ 0.486348] pci 0000:03:01.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486374] pci 0000:03:01.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486406] pci 0000:03:02.0: PCI bridge to [bus 05-05] [ 0.486444] pci 0000:03:03.0: PCI bridge to [bus 06-06] [ 0.486479] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.486499] pci 0000:02:00.0: bridge window [io 0xd000-0xdfff] [ 0.486522] pci 0000:02:00.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486545] pci 0000:02:00.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486575] pci 0000:00:1c.1: PCI bridge to [bus 02-06] [ 0.486593] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 0.486615] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486637] pci 0000:00:1c.1: bridge window [mem 0xff600000-0xff6fffff pref] [ 0.486710] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.486735] pci 0000:00:1c.0: setting latency timer to 64 [ 0.486774] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.486796] pci 0000:00:1c.1: setting latency timer to 64 [ 0.486817] pci 0000:02:00.0: setting latency timer to 64 [ 0.486836] pci 0000:03:01.0: setting latency timer to 64 [ 0.486858] pci 0000:03:02.0: setting latency timer to 64 [ 0.486880] pci 0000:03:03.0: setting latency timer to 64 [ 0.486893] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.486902] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.486912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.486922] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff] [ 0.486932] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.486941] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff] [ 0.486951] pci_bus 0000:01: resource 2 [mem 0xff700000-0xff7fffff pref] [ 0.486961] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.486970] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.486980] pci_bus 0000:02: resource 2 [mem 0xff600000-0xff6fffff pref] [ 0.486989] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.486998] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487008] pci_bus 0000:03: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487018] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.487028] pci_bus 0000:04: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487038] pci_bus 0000:04: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487177] NET: Registered protocol family 2 [ 0.487405] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.488397] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.489792] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.490493] TCP: Hash tables configured (established 131072 bind 65536) [ 0.490525] TCP reno registered [ 0.490551] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.490590] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.490898] NET: Registered protocol family 1 [ 0.490970] pci 0000:00:02.0: Boot video device [ 0.491052] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.491092] pci 0000:00:1d.0: PCI INT A disabled [ 0.491134] pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.491174] pci 0000:00:1d.1: PCI INT B disabled [ 0.491220] pci 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 0.491259] pci 0000:00:1d.2: PCI INT C disabled [ 0.491307] pci 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 0.864431] Freeing initrd memory: 13820k freed [ 2.088042] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.088207] pci 0000:00:1d.7: PCI INT D disabled [ 2.088267] PCI: CLS 64 bytes, default 64 [ 2.089248] audit: initializing netlink socket (disabled) [ 2.089287] type=2000 audit(1349363630.084:1): initialized [ 2.144783] highmem bounce pool size: 64 pages [ 2.144808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 2.160057] VFS: Disk quotas dquot_6.5.2 [ 2.160232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.161716] fuse init (API version 7.17) [ 2.161995] msgmni has been set to 1713 [ 2.162925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.163008] io scheduler noop registered [ 2.163023] io scheduler deadline registered [ 2.163048] io scheduler cfq registered (default) [ 2.163339] pcieport 0000:00:1c.0: setting latency timer to 64 [ 2.163530] pcieport 0000:00:1c.1: setting latency timer to 64 [ 2.163706] pcieport 0000:02:00.0: setting latency timer to 64 [ 2.163873] pcieport 0000:03:01.0: setting latency timer to 64 [ 2.163964] pcieport 0000:03:01.0: irq 40 for MSI/MSI-X [ 2.164193] pcieport 0000:03:02.0: setting latency timer to 64 [ 2.164272] pcieport 0000:03:02.0: irq 41 for MSI/MSI-X [ 2.164453] pcieport 0000:03:03.0: setting latency timer to 64 [ 2.164531] pcieport 0000:03:03.0: irq 42 for MSI/MSI-X [ 2.164783] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt [ 2.164801] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.164816] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded [ 2.164853] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt [ 2.164867] pcieport 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.164880] pcieport 0000:03:01.0: Signaling PME through PCIe PME interrupt [ 2.164892] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 2.164904] pcieport 0000:03:02.0: Signaling PME through PCIe PME interrupt [ 2.164917] pcieport 0000:03:03.0: Signaling PME through PCIe PME interrupt [ 2.164932] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded [ 2.164988] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.165115] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 8110 ss_vid 8086 ss_did 8119 [ 2.165177] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded [ 2.165199] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 8112 ss_vid 8086 ss_did 8119 [ 2.165260] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded [ 2.165290] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.165488] intel_idle: MWAIT substates: 0x3020220 [ 2.165508] intel_idle: v0.4 model 0x1C [ 2.165513] intel_idle: lapic_timer_reliable_states 0x2 [ 2.165519] Marking TSC unstable due to TSC halts in idle states deeper than C2 [ 2.165779] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 2.165855] ACPI: Lid Switch [LID] [ 2.165983] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 2.166005] ACPI: Power Button [PWRB] [ 2.173811] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.173829] ACPI: Thermal Zone [TZ00] (48 C) [ 2.174004] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.174018] ACPI: Thermal Zone [TZ01] (34 C) [ 2.174194] thermal LNXTHERM:02: registered as thermal_zone2 [ 2.174207] ACPI: Thermal Zone [TZ02] (34 C) [ 2.174378] thermal LNXTHERM:03: registered as thermal_zone3 [ 2.174392] ACPI: Thermal Zone [TZ03] (34 C) [ 2.174503] ERST: Table is not found! [ 2.174513] GHES: HEST is not enabled! [ 2.174601] isapnp: Scanning for PnP cards... [ 2.176175] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 2.196702] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.292409] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.528909] isapnp: No Plug & Play device found [ 2.588733] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.624523] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.640702] Linux agpgart interface v0.103 [ 2.645138] brd: module loaded [ 2.647452] loop: module loaded [ 2.648149] pata_acpi 0000:00:1f.1: setting latency timer to 64 [ 2.649238] Fixed MDIO Bus: probed [ 2.649315] tun: Universal TUN/TAP device driver, 1.6 [ 2.649327] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 2.649524] PPP generic driver version 2.4.2 [ 2.649824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.649884] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 2.649937] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.649946] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.650082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.650148] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.654045] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 2.654093] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd02c4000 [ 2.668035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.668392] hub 1-0:1.0: USB hub found [ 2.668413] hub 1-0:1.0: 8 ports detected [ 2.668618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.668666] uhci_hcd: USB Universal Host Controller Interface driver [ 2.668726] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 2.668751] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.668759] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.668910] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.668981] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000f040 [ 2.669335] hub 2-0:1.0: USB hub found [ 2.669355] hub 2-0:1.0: 2 ports detected [ 2.669508] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 2.669531] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.669538] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.669675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.669739] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f020 [ 2.670099] hub 3-0:1.0: USB hub found [ 2.670118] hub 3-0:1.0: 2 ports detected [ 2.670271] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 2.670295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.670302] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.670435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.670502] uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000f000 [ 2.670869] hub 4-0:1.0: USB hub found [ 2.670888] hub 4-0:1.0: 2 ports detected [ 2.671186] usbcore: registered new interface driver libusual [ 2.671332] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.673408] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.673437] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.673844] mousedev: PS/2 mouse device common for all mice [ 2.674272] rtc_cmos 00:08: RTC can wake from S4 [ 2.674482] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 2.674529] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 2.674691] device-mapper: uevent: version 1.0.3 [ 2.674903] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.675024] EISA: Probing bus 0 at eisa.0 [ 2.675037] EISA: Cannot allocate resource for mainboard [ 2.675050] Cannot allocate resource for EISA slot 1 [ 2.675061] Cannot allocate resource for EISA slot 2 [ 2.675072] Cannot allocate resource for EISA slot 3 [ 2.675083] Cannot allocate resource for EISA slot 4 [ 2.675094] Cannot allocate resource for EISA slot 5 [ 2.675105] Cannot allocate resource for EISA slot 6 [ 2.675116] Cannot allocate resource for EISA slot 7 [ 2.675127] Cannot allocate resource for EISA slot 8 [ 2.675137] EISA: Detected 0 cards. [ 2.675161] cpufreq-nforce2: No nForce2 chipset. [ 2.675401] cpuidle: using governor ladder [ 2.675786] cpuidle: using governor menu [ 2.675797] EFI Variables Facility v0.08 2004-May-17 [ 2.676429] TCP cubic registered [ 2.676751] NET: Registered protocol family 10 [ 2.678031] NET: Registered protocol family 17 [ 2.678052] Registering the dns_resolver key type [ 2.678107] Using IPI No-Shortcut mode [ 2.678515] PM: Hibernation image not present or could not be loaded. [ 2.678543] registered taskstats version 1 [ 2.701145] Magic number: 0:84:234 [ 2.701312] rtc_cmos 00:08: setting system clock to 2012-10-04 15:13:51 UTC (1349363631) [ 2.702280] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.702294] EDD information not available. [ 2.702858] Freeing unused kernel memory: 740k freed [ 2.703630] Write protecting the kernel text: 5816k [ 2.703692] Write protecting the kernel read-only data: 2376k [ 2.703706] NX-protecting the kernel data: 4424k [ 2.751226] udevd[84]: starting version 175 [ 2.980162] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 3.001394] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.001474] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.001554] r8169 0000:01:00.0: setting latency timer to 64 [ 3.001654] r8169 0000:01:00.0: irq 43 for MSI/MSI-X [ 3.004220] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8416000, 00:18:92:03:10:46, XID 1c4000c0 IRQ 43 [ 3.004254] r8169 0000:01:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.004347] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.005085] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 3.005182] r8169 0000:04:00.0: setting latency timer to 64 [ 3.005292] r8169 0000:04:00.0: irq 44 for MSI/MSI-X [ 3.007187] r8169 0000:04:00.0: eth1: RTL8168c/8111c at 0xf8418000, 00:18:92:03:10:47, XID 1c4000c0 IRQ 44 [ 3.007224] r8169 0000:04:00.0: eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.034417] pata_sch 0000:00:1f.1: version 0.2 [ 3.034518] pata_sch 0000:00:1f.1: setting latency timer to 64 [ 3.036698] scsi0 : pata_sch [ 3.039842] scsi1 : pata_sch [ 3.040913] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf060 irq 14 [ 3.040940] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf068 irq 15 [ 3.131850] Initializing USB Mass Storage driver... [ 3.136405] scsi2 : usb-storage 1-1:1.0 [ 3.136642] usbcore: registered new interface driver usb-storage [ 3.136656] USB Mass Storage support registered. [ 3.524465] usb 3-1: new low-speed USB device number 2 using uhci_hcd [ 3.968144] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 4.137903] scsi 2:0:0:0: Direct-Access TS TS4GUFM-H 1100 PQ: 0 ANSI: 0 CCS [ 4.140067] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.140590] sd 2:0:0:0: [sda] 8028160 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 4.141597] sd 2:0:0:0: [sda] Write Protect is off [ 4.141618] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.142974] sd 2:0:0:0: [sda] No Caching mode page present [ 4.143000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.145837] sd 2:0:0:0: [sda] No Caching mode page present [ 4.145858] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.147931] sda: sda1 sda2 < sda5 > [ 4.150972] sd 2:0:0:0: [sda] No Caching mode page present [ 4.151001] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.151023] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.249168] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2 [ 4.249579] generic-usb 0003:046A:004B.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:004b] on usb-0000:00:1d.1-1/input0 [ 4.287805] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3 [ 4.289235] generic-usb 0003:046A:004B.0002: input,hidraw1: USB HID v1.11 Mouse [HID 046a:004b] on usb-0000:00:1d.1-1/input1 [ 4.297604] input: EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input4 [ 4.298913] generic-usb 0003:04E7:0050.0003: input,hidraw2: USB HID v1.00 Pointer [EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface] on usb-0000:00:1d.1-2/input0 [ 4.299878] usbcore: registered new interface driver usbhid [ 4.299925] usbhid: USB HID core driver [ 4.352639] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 4.352661] EXT4-fs (sda1): write access will be enabled during recovery [ 8.519257] EXT4-fs (sda1): recovery complete [ 8.564389] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 14.280922] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.280944] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.310368] udevd[308]: starting version 175 [ 14.353873] Adding 1045500k swap on /dev/sda5. Priority:-1 extents:1 across:1045500k [ 14.428718] lp: driver loaded but no devices found [ 14.521667] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 15.073459] [drm] Initialized drm 1.1.0 20060810 [ 15.097073] psb_gfx: module is from the staging directory, the quality is unknown, you have been warned. [ 15.180630] gma500 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 15.180648] gma500 0000:00:02.0: setting latency timer to 64 [ 15.182117] Stolen memory information [ 15.182127] base in RAM: 0x7f800000 [ 15.182134] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong [ 15.182143] the correct size should be: 8M(dvmt mode=3) [ 15.234889] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K [ 15.235126] [drm] SGX core id = 0x01130000 [ 15.235135] [drm] SGX core rev major = 0x01, minor = 0x02 [ 15.235143] [drm] SGX core rev maintenance = 0x01, designer = 0x00 [ 15.268796] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 15.269888] acpi device:04: registered as cooling_device2 [ 15.270568] acpi device:05: registered as cooling_device3 [ 15.270947] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 15.271238] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 15.271424] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 15.271434] [drm] No driver support for vblank timestamp query. [ 15.374694] type=1400 audit(1349363644.167:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=435 comm="apparmor_parser" [ 15.385518] type=1400 audit(1349363644.179:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=435 comm="apparmor_parser" [ 15.386369] type=1400 audit(1349363644.179:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=435 comm="apparmor_parser" [ 15.677514] r8169 0000:01:00.0: eth0: link down [ 15.694828] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.537490] gma500 0000:00:02.0: allocated 800x480 fb [ 16.558066] fbcon: psbfb (fb0) is primary device [ 16.747122] gma500 0000:00:02.0: BL bug: Reg 00000000 save 00000000 [ 16.775550] Console: switching to colour frame buffer device 100x30 [ 16.781804] fb0: psbfb frame buffer device [ 16.781812] drm: registered panic notifier [ 16.870168] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0 [ 16.871166] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871186] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871207] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 16.871284] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 29.338953] r8169 0000:01:00.0: eth0: link up [ 29.339471] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.427223] init: failsafe main process (675) killed by TERM signal [ 31.522411] type=1400 audit(1349363660.316:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=889 comm="apparmor_parser" [ 31.523956] type=1400 audit(1349363660.316:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=889 comm="apparmor_parser" [ 31.524882] type=1400 audit(1349363660.320:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=889 comm="apparmor_parser" [ 31.525940] type=1400 audit(1349363660.320:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=891 comm="apparmor_parser" [ 34.526445] postgres (1003): /proc/1003/oom_adj is deprecated, please use /proc/1003/oom_score_adj instead. [ 40.144048] eth0: no IPv6 routers present

  Read the article

• How can I selectively increase latency? E.g. throttle games

  - by Arcymag

  Basically, I want networked games to run poorly on a network, but I want everything else to run smoothly. I would also appreciate advice on blocking games in general. As far as I can tell, there's a few ways to completely prevent an internet game from running: Blocking entirely via DNS configuration (e.g. hosts file), or router DNS configuration Blocking entirely via a separate DNS server Blocking the application, by uninstalling or some kind of access control Blocking the application by automatically killing the process every once in a while Blocking the application by corrupting files periodically However, I would like a more subtle way to block a program. Something that either: Increases latency (would this be doable through some kind of QoS like what DD-WRT offers?) Increases latency by using a special routing configuration for specific target IPs Throttle other systems resources, such as memory, IO, or CPU Screw around with keyboard configurations when a game is launched I would like this to work on MacOSX and Windows, but Linux would be great too. FYI I don't have a kid, but I was brainstorming with some friends and parents.

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• Drivers for NVIDIA 520M not working in Ubuntu 12.04

  - by Don

  I am aware that this is nominally a duplicate question, however I've read the other questions and haven't been able to resolve my problem after many hours and attempts, so please don't delete it. Additionally, it seems like many answers to the other questions are specifically dependent on certain situations. My situation being different from the others I found represented, here's my question. Until last night, I had Ubuntu 12.04 installed with Wubi, and it ran ok, though slowly and with occasional hangs. So I partitioned the drive and installed 12.04 in its own partition. Now when I start it, I am stuck using 2D. I believe this is an NVIDIA bug. My NVIDIA card is a GT 520M and my machine has Optimus. Additional Drivers only displays my wireless driver. Going to System Settings Details Graphics shows Driver:Unknown, Experience:Standard. I downloaded the driver from the NVIDIA website, and ran the installer with no errors, except that the "distribution-provided pre-install script failed". After rebooting, my screen was stuck at 640X480, which was fixed by editing /etc/X11/xorg.conf However, I still was stuck in 2D, and nothing else had changed either. A thread suggested something called Bumblebee. I tried that, and when I ran optirun firefoxI got a frozen blank screen. Following another suggestion, I checked the BIOS to try and disable Optimus. I found and ran myriad other commands to try and fix the problem and nothing changed. Now I have just done a clean re-install of Ubuntu. From there, I: Installed all the updates Downloaded the NVIDIA driver Installed it Got screen stuck at 640X480, fixed in xorg.conf. To recap the problem: I can't get the NVIDIA drivers working I am stuck using 2D I'm an idiot I think if the first one is solved, the solution to the second will naturally follow. If you need me to provide any other information, I'd be happy to. From what I've seen in other threads, I think this information may help: lsmod: dh@donsMachine:~$ lsmod Module Size Used by nvidia 12353161 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 223867 1 joydev 17693 0 parport_pc 32866 0 ppdev 17113 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event lib80211_crypt_tkip 17390 0 wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device psmouse 87692 0 serio_raw 13211 0 i915 468745 2 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm drm_kms_helper 46978 1 i915 drm 242038 3 i915,drm_kms_helper mei 41616 0 i2c_algo_bit 13423 1 i915 mxm_wmi 12979 0 acer_wmi 28418 0 sparse_keymap 13890 1 acer_wmi video 19596 1 i915 wmi 19256 2 mxm_wmi,acer_wmi mac_hid 13253 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp tg3 152032 0 sdhci_pci 18826 0 sdhci 33205 1 sdhci_pci lspci -nn | grep VGA dh@donsMachine:~$ lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation Device [10de:0df7] (rev a1) lshw dh@donsMachine:~$ sudo lshw [sudo] password for dh: donsmachine description: Notebook product: EasyNote TS44HR () vendor: Packard Bell version: V1.12 serial: LXBWZ02017134209D71601 width: 64 bits capabilities: smbios-2.7 dmi-2.7 vsyscall32 configuration: boot=normal chassis=notebook uuid=16FE576B-CA15-11E0-B096-B870F4E51243 *-core description: Motherboard product: SJV50_HR vendor: Packard Bell physical id: 0 version: Base Board Version serial: Base Board Serial Number slot: Base Board Chassis Location *-firmware description: BIOS vendor: Packard Bell physical id: 0 version: V1.12 date: 07/11/2011 size: 1MiB capacity: 2496KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppynec int13floppytoshiba int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int9keyboard int10video acpi usb biosbootspecification *-memory description: System Memory physical id: 1b slot: System board or motherboard size: 4GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NS-CG vendor: Nanya Technology physical id: 0 serial: 598E126E slot: ChannelA-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM [empty] physical id: 1 slot: ChannelA-DIMM1 *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: NT2GC64B88B0NS-CG vendor: Nanya Technology physical id: 2 serial: 159E126C slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: DIMM [empty] physical id: 3 slot: ChannelB-DIMM1 *-cpu description: CPU product: Intel(R) Core(TM) i3-2330M CPU @ 2.20GHz vendor: Intel Corp. physical id: 2e bus info: cpu@0 version: Intel(R) Core(TM) i3-2330M CPU @ 2.20GHz slot: CPU1 size: 2GHz capacity: 4GHz width: 64 bits clock: 1333MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer xsave avx lahf_lm arat epb xsaveopt pln pts tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=2 enabledcores=2 threads=4 *-cache:0 description: L1 cache physical id: 30 slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through instruction *-cache:1 description: L2 cache physical id: 31 slot: L2 Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through unified *-cache:2 description: L3 cache physical id: 32 slot: L3 Cache size: 3MiB capacity: 3MiB capabilities: synchronous internal write-through unified *-cache description: L1 cache physical id: 2f slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through data *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:2000(size=4096) memory:d0000000-d10fffff ioport:a0000000(size=301989888) *-display description: VGA compatible controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:16 memory:d0000000-d0ffffff memory:a0000000-afffffff memory:b0000000-b1ffffff ioport:2000(size=128) memory:d1000000-d107ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:43 memory:d1400000-d17fffff memory:c0000000-cfffffff ioport:3000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:42 memory:d1a04000-d1a0400f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 04 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:d1a0a000-d1a0a3ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:44 memory:d1a00000-d1a03fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b4 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 memory:9fb00000-9fbfffff ioport:d1800000(size=1048576) *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: b8:70:f4:e5:12:43 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 firmware=sb latency=0 link=no multicast=yes port=twisted pair resources: irq:16 memory:d1830000-d183ffff memory:d1840000-d184ffff memory:d1850000-d18507ff *-generic:0 description: SD Host controller product: NetXtreme BCM57765 Memory Card Reader vendor: Broadcom Corporation physical id: 0.1 bus info: pci@0000:02:00.1 version: 10 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=sdhci-pci latency=0 resources: irq:17 memory:d1800000-d180ffff *-generic:1 UNCLAIMED description: System peripheral product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0.2 bus info: pci@0000:02:00.2 version: 10 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1810000-d181ffff *-generic:2 UNCLAIMED description: System peripheral product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0.3 bus info: pci@0000:02:00.3 version: 10 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:d1820000-d182ffff *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b4 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:d1900000-d19fffff *-network description: Wireless interface product: BCM43225 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 68:a3:c4:44:81:96 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.0.12 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d1900000-d1903fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 04 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:d1a09000-d1a093ff *-isa description: ISA bridge product: HM65 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 04 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi1 version: 04 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:41 ioport:3098(size=8) ioport:30bc(size=4) ioport:3090(size=8) ioport:30b8(size=4) ioport:3060(size=32) memory:d1a08000-d1a087ff *-disk description: ATA Disk product: ST9500325AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 0001 serial: S2W1AMSX size: 465GiB (500GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=a45f21e9 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: 46aa-2a25 size: 19GiB capacity: 20GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2011-08-25 21:32:00 filesystem=ntfs label=PQSERVICE state=clean *-volume:1 description: Windows NTFS volume physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 version: 3.1 serial: 10aa-ad1a size: 98MiB capacity: 100MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2011-08-25 21:32:03 filesystem=ntfs label=SYSTEM RESERVED state=clean *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 668c5afc-182e-ff4b-b084-3cc09f54972d size: 395GiB capacity: 395GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2011-08-25 21:32:03 filesystem=ntfs label=Don's Machine state=clean *-volume:3 description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 size: 49GiB capacity: 49GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 3945MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 46GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,barrier=1,data=ordered state=mounted *-cdrom description: DVD-RAM writer product: DVD-RW DVRTD11RS vendor: PIONEER physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 1.01 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 04 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:d1a06000-d1a060ff ioport:3040(size=32) *-power UNCLAIMED description: OEM_Define1 product: OEM_Define5 vendor: OEM_Define2 physical id: 1 version: OEM_Define6 serial: OEM_Define3 capacity: 75mWh *-battery description: Lithium Ion Battery product: CRB Battery 0 vendor: -Virtual Battery 0- physical id: 2 version: 10/12/2007 serial: Battery 0 slot: Fake

  Read the article

• Is minimum latency fixed by the speed of light?

  - by JavaRocky

  Suppose i had a fiber optic link from one side of the planet to the other side of the planet. Is it safe to say, that with current technology, the latency of communication can never be reduced? Understand that a fiber optic cable is not a perfect medium thus data only travels close to the speed of light. Also lets consider that i will not be drilling a hole thru the center of the earth and it is just running along the ocean.

  Read the article

• Kubuntu 12.04 - Touchpad and keyboard stopped working at random

  - by StepTNT

  As in the title, I've got this problem with my Kubuntu 12.04. At first I've thought that the whole system was hung, but it happened again 5 minutes ago and, while the keyboard and the touchpad stopped working, the music was still playing, so I guess that's just an "input" problem, because the system was still working! Any solution? Is there some data that you need to know about my setup? EDIT: Added my lshw outout description: Notebook product: N53SV () vendor: ASUSTeK Computer Inc. version: 1.0 serial: B2N0AS17695408A width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=notebook family=N uuid=8083F2DA-A43E-E081-3F3F-BCAEC55F8AA1 *-core description: Motherboard product: N53SV vendor: ASUSTeK Computer Inc. physical id: 0 version: 1.0 serial: BSN12345678901234567 slot: MIDDLE *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: N53SV.214 date: 08/10/2011 size: 64KiB capacity: 2496KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer acpi usb smartbattery biosbootspecification *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: To Be Filled By O.E.M. slot: CPU 1 size: 800MHz capacity: 4GHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer xsave avx lahf_lm ida arat epb xsaveopt pln pts tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=1 threads=2 *-cache description: L1 cache physical id: 5 slot: L1-Cache size: 32KiB capacity: 32KiB capabilities: internal write-back instruction *-memory description: System Memory physical id: 40 slot: System board or motherboard size: 10GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: 99U5428-040.A00LF vendor: Kingston physical id: 0 serial: 103C28C3 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 58383D1F slot: ChannelA-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 2 serial: 58183D19 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0,8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 3 serial: 58183C8F slot: ChannelB-DIMM1 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz configuration: driver=agpgart-intel resources: irq:0 *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:d000(size=4096) memory:db000000-dc0fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:db000000-dbffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:d000(size=128) memory:dc000000-dc07ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:47 memory:dc400000-dc7fffff memory:b0000000-bfffffff ioport:e000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei latency=0 resources: irq:48 memory:df00b000-df00b00f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:16 memory:df008000-df0083ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:49 memory:df000000-df003fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:c000(size=4096) memory:de600000-deffffff ioport:d4200000(size=10485760) *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:b000(size=4096) memory:ddc00000-de5fffff ioport:d3700000(size=10485760) *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 48:5d:60:f2:2c:fd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-24-generic firmware=N/A ip=192.168.1.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:ddc00000-ddc0ffff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:a000(size=4096) memory:dd200000-ddbfffff ioport:d2c00000(size=10485760) *-usb description: USB controller product: FL1000G USB 3.0 Host Controller vendor: Fresco Logic physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:dd200000-dd20ffff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:44 ioport:9000(size=4096) memory:dc800000-dd1fffff ioport:d2100000(size=10485760) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 06 serial: bc:ae:c5:5f:8a:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168e-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:46 ioport:9000(size=256) memory:d2104000-d2104fff memory:d2100000-d2103fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:df007000-df0073ff *-isa description: ISA bridge product: HM65 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: SATA controller product: 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 logical name: scsi2 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:45 ioport:e0b0(size=8) ioport:e0a0(size=4) ioport:e090(size=8) ioport:e080(size=4) ioport:e060(size=32) memory:df006000-df0067ff *-disk description: ATA Disk product: ST9750420AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 0002 serial: 5WS0A7QR size: 698GiB (750GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=e0c5913d *-volume:0 description: Windows FAT volume vendor: MSDOS5.0 physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: FAT32 serial: 4ce5-3acb size: 3004MiB capacity: 3004MiB capabilities: primary fat initialized configuration: FATs=2 filesystem=fat *-volume:1 description: EXT4 volume vendor: Linux physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 logical name: / version: 1.0 serial: c198cc2a-d86a-4460-a4d5-3fc0b21e439c size: 28GiB capacity: 28GiB capabilities: primary journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-03-15 16:53:54 filesystem=ext4 lastmountpoint=/ modified=2012-05-02 18:52:04 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,acl,barrier=1,data=ordered mounted=2012-05-09 19:06:01 state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 version: 3.1 serial: 4c1cdebc-ec09-2947-a3b5-c1f9f1cddc1c size: 152GiB capacity: 152GiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2011-02-22 16:02:47 filesystem=ntfs label=OS state=clean *-volume:3 description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 size: 514GiB capacity: 514GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 10GiB capabilities: nofs *-logicalvolume:1 description: HPFS/NTFS partition physical id: 6 logical name: /dev/sda6 capacity: 504GiB *-cdrom description: DVD-RAM writer product: BD-MLT UJ240AS vendor: MATSHITA physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/sr0 version: 1.00 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:df005000-df0050ff ioport:e040(size=32)

  Read the article

• How can I fix latency problems for car game?

  - by Freddy

  Basically I'm trying to make a online car racing game for IOS using Game Center real time multiplayer. I have setup a timer that sends data every 0.02 seconds to the other player with the current position and current angle. However sometimes, it will take LONGER then these 0.02 seconds for the package to be sent and then received. In this case i have implemented a method that "calculate" what the next position should be if no position is received based on the last position and angle. However, when the data then receives for let say 0.04 seconds after, it will change back to the last position, which will result in the car "jumping" back and lag. And If i just keep ignoring the data it will never take any input from the other user. Is their any way to prevent this? I suppose this needs to be fixed with some client-sided algorithm.

  Read the article

• How much audio latency is noticeable by human brain?

  - by Borek

  I am choosing a wireless headset for my PC (I hate cables) and am looking at Sennheiser RS 170 / 180. They supposedly sound great, however, there is a 25ms audio latency. I've heard that this is OK when watching TV or listening musing but is bad for games. The question is - has there been any research / hard data that would show how much of a delay is noticeable by human brain? 25ms doesn't sound like a lot but I may be wrong.

  Read the article

• Unity not Working 14.04

  - by Back.Slash

  I am using Ubuntu 14.04 LTS x64. I did a sudo apt-get upgrade yesterday and restarted my PC. Now my taskbar and panel are missing. When I try to restart Unity using unity --replace Then I get error: unity-panel-service stop/waiting compiz (core) - Info: Loading plugin: core compiz (core) - Info: Starting plugin: core unity-panel-service start/running, process 3906 compiz (core) - Info: Loading plugin: ccp compiz (core) - Info: Starting plugin: ccp compizconfig - Info: Backend : gsettings compizconfig - Info: Integration : true compizconfig - Info: Profile : unity compiz (core) - Info: Loading plugin: composite compiz (core) - Info: Starting plugin: composite compiz (core) - Info: Loading plugin: opengl compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Unity is fully supported by your hardware. compiz (core) - Info: Starting plugin: opengl libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/i965_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/i965_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/i965_dri.so failed (${ORIGIN}/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/i965_dri.so failed (/usr/lib/dri/i965_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: i965_dri.so libGL error: driver pointer missing libGL error: failed to load driver: i965 libGL error: dlopen /usr/lib/x86_64-linux-gnu/dri/swrast_dri.so failed (/usr/lib/x86_64-linux-gnu/dri/swrast_dri.so: undefined symbol: _glapi_tls_Dispatch) libGL error: dlopen ${ORIGIN}/dri/swrast_dri.so failed (${ORIGIN}/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: dlopen /usr/lib/dri/swrast_dri.so failed (/usr/lib/dri/swrast_dri.so: cannot open shared object file: No such file or directory) libGL error: unable to load driver: swrast_dri.so libGL error: failed to load driver: swrast compiz (core) - Info: Loading plugin: compiztoolbox compiz (core) - Info: Starting plugin: compiztoolbox compiz (core) - Info: Loading plugin: decor compiz (core) - Info: Starting plugin: decor compiz (core) - Info: Loading plugin: vpswitch compiz (core) - Info: Starting plugin: vpswitch compiz (core) - Info: Loading plugin: snap compiz (core) - Info: Starting plugin: snap compiz (core) - Info: Loading plugin: mousepoll compiz (core) - Info: Starting plugin: mousepoll compiz (core) - Info: Loading plugin: resize compiz (core) - Info: Starting plugin: resize compiz (core) - Info: Loading plugin: place compiz (core) - Info: Starting plugin: place compiz (core) - Info: Loading plugin: move compiz (core) - Info: Starting plugin: move compiz (core) - Info: Loading plugin: wall compiz (core) - Info: Starting plugin: wall compiz (core) - Info: Loading plugin: grid compiz (core) - Info: Starting plugin: grid compiz (core) - Info: Loading plugin: regex compiz (core) - Info: Starting plugin: regex compiz (core) - Info: Loading plugin: imgpng compiz (core) - Info: Starting plugin: imgpng compiz (core) - Info: Loading plugin: session compiz (core) - Info: Starting plugin: session I/O warning : failed to load external entity "/home/sumeet/.compiz/session/10de541a813cc1a8fc140170575114755000000020350005" compiz (core) - Info: Loading plugin: gnomecompat compiz (core) - Info: Starting plugin: gnomecompat compiz (core) - Info: Loading plugin: animation compiz (core) - Info: Starting plugin: animation compiz (core) - Info: Loading plugin: fade compiz (core) - Info: Starting plugin: fade compiz (core) - Info: Loading plugin: unitymtgrabhandles compiz (core) - Info: Starting plugin: unitymtgrabhandles compiz (core) - Info: Loading plugin: workarounds compiz (core) - Info: Starting plugin: workarounds compiz (core) - Info: Loading plugin: scale compiz (core) - Info: Starting plugin: scale compiz (core) - Info: Loading plugin: expo compiz (core) - Info: Starting plugin: expo compiz (core) - Info: Loading plugin: ezoom compiz (core) - Info: Starting plugin: ezoom compiz (core) - Info: Loading plugin: unityshell compiz (core) - Info: Starting plugin: unityshell WARN 2014-06-02 18:46:23 unity.glib.dbus.server GLibDBusServer.cpp:579 Can't register object 'org.gnome.Shell' yet as we don't have a connection, waiting for it... ERROR 2014-06-02 18:46:23 unity.debug.interface DebugDBusInterface.cpp:216 Unable to load entry point in libxpathselect: libxpathselect.so.1.4: cannot open shared object file: No such file or directory compiz (unityshell) - Error: GL_ARB_vertex_buffer_object not supported ERROR 2014-06-02 18:46:23 unity.shell.compiz unityshell.cpp:3850 Impossible to delete the unity locked stamp file compiz (core) - Error: Plugin initScreen failed: unityshell compiz (core) - Error: Failed to start plugin: unityshell compiz (core) - Info: Unloading plugin: unityshell X Error of failed request: BadWindow (invalid Window parameter) Major opcode of failed request: 3 (X_GetWindowAttributes) Resource id in failed request: 0x3e000c9 Serial number of failed request: 10115 Current serial number in output stream: 10116 Any help would be highly appreciated. EDIT : My PC configuration description: Portable Computer product: Dell System XPS L502X (System SKUNumber) vendor: Dell Inc. version: 0.1 serial: 1006ZP1 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: administrator_password=unknown boot=normal chassis=portable family=HuronRiver System frontpanel_password=unknown keyboard_password=unknown power-on_password=unknown sku=System SKUNumber uuid=44454C4C-3000-1030-8036-B1C04F5A5031 *-core description: Motherboard product: 0YR8NN vendor: Dell Inc. physical id: 0 version: A00 serial: .1006ZP1.CN4864314C0560. slot: Part Component *-firmware description: BIOS vendor: Dell Inc. physical id: 0 version: A11 date: 05/29/2012 size: 128KiB capacity: 2496KiB capabilities: pci pnp upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot smartbattery biosbootspecification netboot *-cpu description: CPU product: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz vendor: Intel Corp. physical id: 19 bus info: cpu@0 version: Intel(R) Core(TM) i7-2630QM CPU @ 2.00GHz serial: Not Supported by CPU slot: CPU size: 800MHz capacity: 800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts nopl xtopology nonstop_tsc aperfmperf eagerfpu pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 x2apic popcnt tsc_deadline_timer aes xsave avx lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=4 threads=8 *-cache:0 description: L1 cache physical id: 1a slot: L1-Cache size: 64KiB capacity: 64KiB capabilities: synchronous internal write-through data *-cache:1 description: L2 cache physical id: 1b slot: L2-Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through data *-cache:2 description: L3 cache physical id: 1c slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: synchronous internal write-back unified *-memory description: System Memory physical id: 1d slot: System board or motherboard size: 6GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: M471B5273DH0-CH9 vendor: Samsung physical id: 0 serial: 450F1160 slot: ChannelA-DIMM0 size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: HMT325S6BFR8C-H9 vendor: Hynix/Hyundai physical id: 1 serial: 0CA0E8E2 slot: ChannelB-DIMM0 size: 2GiB width: 64 bits clock: 1333MHz (0.8ns) *-pci description: Host bridge product: 2nd Generation Core Processor Family DRAM Controller vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 09 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port vendor: Intel Corporation physical id: 1 bus info: pci@0000:00:01.0 version: 09 width: 32 bits clock: 33MHz capabilities: pci pm msi pciexpress normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:3000(size=4096) memory:f0000000-f10fffff ioport:c0000000(size=301989888) *-generic UNCLAIMED description: Unassigned class product: Illegal Vendor ID vendor: Illegal Vendor ID physical id: 0 bus info: pci@0000:01:00.0 version: ff width: 32 bits clock: 66MHz capabilities: bus_master vga_palette cap_list configuration: latency=255 maxlatency=255 mingnt=255 resources: memory:f0000000-f0ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:3000(size=128) memory:f1000000-f107ffff *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:52 memory:f1400000-f17fffff memory:e0000000-efffffff ioport:4000(size=64) *-communication description: Communication controller product: 6 Series/C200 Series Chipset Family MEI Controller #1 vendor: Intel Corporation physical id: 16 bus info: pci@0000:00:16.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi bus_master cap_list configuration: driver=mei_me latency=0 resources: irq:50 memory:f1c05000-f1c0500f *-usb:0 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:16 memory:f1c09000-f1c093ff *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:53 memory:f1c00000-f1c03fff *-pci:1 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode cap_list configuration: driver=pcieport resources: irq:16 *-pci:2 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 memory:f1b00000-f1bfffff *-network description: Wireless interface product: Centrino Wireless-N 1030 [Rainbow Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 34 serial: bc:77:37:14:47:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-27-generic firmware=18.168.6.1 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:f1b00000-f1b01fff *-pci:3 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 4 vendor: Intel Corporation physical id: 1c.3 bus info: pci@0000:00:1c.3 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:19 memory:f1a00000-f1afffff *-usb description: USB controller product: uPD720200 USB 3.0 Host Controller vendor: NEC Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 04 width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:19 memory:f1a00000-f1a01fff *-pci:4 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 5 vendor: Intel Corporation physical id: 1c.4 bus info: pci@0000:00:1c.4 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:f1900000-f19fffff *-pci:5 description: PCI bridge product: 6 Series/C200 Series Chipset Family PCI Express Root Port 6 vendor: Intel Corporation physical id: 1c.5 bus info: pci@0000:00:1c.5 version: b5 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 ioport:2000(size=4096) ioport:f1800000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: 06 serial: 14:fe:b5:a3:ac:40 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=172.19.167.151 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:49 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff *-usb:1 description: USB controller product: 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci-pci latency=0 resources: irq:23 memory:f1c08000-f1c083ff *-isa description: ISA bridge product: HM67 Express Chipset Family LPC Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: driver=lpc_ich latency=0 resources: irq:0 *-ide:0 description: IDE interface product: 6 Series/C200 Series Chipset Family 4 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40b8(size=8) ioport:40cc(size=4) ioport:40b0(size=8) ioport:40c8(size=4) ioport:4090(size=16) ioport:4080(size=16) *-serial UNCLAIMED description: SMBus product: 6 Series/C200 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:f1c04000-f1c040ff ioport:efa0(size=32) *-ide:1 description: IDE interface product: 6 Series/C200 Series Chipset Family 2 port SATA IDE Controller vendor: Intel Corporation physical id: 1f.5 bus info: pci@0000:00:1f.5 version: 05 width: 32 bits clock: 66MHz capabilities: ide pm bus_master cap_list configuration: driver=ata_piix latency=0 resources: irq:19 ioport:40a8(size=8) ioport:40c4(size=4) ioport:40a0(size=8) ioport:40c0(size=4) ioport:4070(size=16) ioport:4060(size=16) *-scsi:0 physical id: 1 logical name: scsi0 capabilities: emulated *-disk description: ATA Disk product: SAMSUNG HN-M640M physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 2AR1 serial: S2T3J1KBC00006 size: 596GiB (640GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sectorsize=512 signature=6b746d91 *-volume:0 description: Windows NTFS volume physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 version: 3.1 serial: 0272-3e7f size: 348MiB capacity: 350MiB capabilities: primary bootable ntfs initialized configuration: clustersize=4096 created=2013-09-18 12:20:45 filesystem=ntfs label=System Reserved modified_by_chkdsk=true mounted_on_nt4=true resize_log_file=true state=dirty upgrade_on_mount=true *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 116GiB capacity: 116GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume:0 description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 6037MiB capabilities: nofs *-logicalvolume:1 description: Linux filesystem partition physical id: 6 logical name: /dev/sda6 logical name: / capacity: 110GiB configuration: mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,data=ordered state=mounted *-volume:2 description: Windows NTFS volume physical id: 3 bus info: scsi@0:0.0.0,3 logical name: /dev/sda3 logical name: /media/os version: 3.1 serial: 4e7853ec-5555-a74d-82e0-9f49798d3772 size: 156GiB capacity: 156GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-19 09:19:00 filesystem=ntfs label=OS mount.fstype=fuseblk mount.options=ro,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 state=mounted *-volume:3 description: Windows NTFS volume physical id: 4 bus info: scsi@0:0.0.0,4 logical name: /dev/sda4 logical name: /media/data version: 3.1 serial: 7666d55f-e1bf-e645-9791-2a1a31b24b9a size: 322GiB capacity: 322GiB capabilities: primary ntfs initialized configuration: clustersize=4096 created=2013-09-17 23:27:01 filesystem=ntfs label=Data modified_by_chkdsk=true mount.fstype=fuseblk mount.options=rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096 mounted_on_nt4=true resize_log_file=true state=mounted upgrade_on_mount=true *-scsi:1 physical id: 2 logical name: scsi1 capabilities: emulated *-cdrom description: DVD-RAM writer product: DVD+-RW GT32N vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/sr0 version: A201 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-battery product: DELL vendor: SANYO physical id: 1 version: 2008 serial: 1.0 slot: Rear capacity: 57720mWh configuration: voltage=11.1V `

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >