Search Results

Search found 7654 results on 307 pages for 'module'.

Page 8/307 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

  • Programmatically check whether a linux kernel module exists or not at runtime

    - by dgraziotin
    I am writing a C daemon, which depends on the existence of two kernel modules in order to do its job. The program does not directly use these (or any other) modules. It only needs them to exist. Therefore, I would like to programmatically check whether these modules are already loaded or not, in order to warn the user at runtime. Before I start to do things like parsing /proc/modules or lsmod output, does a utility function already exist somewhere? Something like is_module_loaded(const char* name); I am pretty sure this has been asked before. However, I think I am missing the correct terms to search for this. Thanks!

    Read the article

  • USB drives not recognized all of a sudden (module usb_storage not loading)

    - by Siddharth
    I am very close to the solution, just need to know how to get usb-storage to load I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

    Read the article

  • Is ServerManager module available on Windows 7?

    - by ruslan
    Is ServerManager module available on Windows 7 Ultimate ? I think (but I'm not sure because I never looked at output before) the PS script that I have worked before but after some problems with IIS7 installation it stopped working. Following script import-module servermanager fails with error Import-Module : The specified module 'servermanager' was not loaded because no valid module file was found in any module directory. At line:1 char:14 + import-module <<<< servermanager + CategoryInfo : ResourceUnavailable: (servermanager:String) [Import-Module], FileNotFoundException + FullyQualifiedErrorId : Modules_ModuleNotFound,Microsoft.PowerShell.Commands.ImportModuleCommand I found recommendation to run Dism.exe /Online /Enable-Feature /FeatureName:ServerManager-PSH-Cmdlets on my machine but it also fails with error Feature name ServerManager-PSH-Cmdlets is unknown.

    Read the article

  • Single python file distribution: module or package?

    - by DanielSank
    Suppose I have a useful python function or class (or whatever) called useful_thing which exists in a single file. There are essentialy two ways to organize the source tree. The first way uses a single module: - setup.py - README.rst - ...etc... - foo.py where useful_thing is defined in foo.py. The second strategy is to make a package: - setup.py - README.rst - ...etc... - foo |-module.py |-__init__.py where useful_thing is defined in module.py. In the package case __init__.py would look like this from foo.module import useful_thing so that in both cases you can do from foo import useful_thing. Question: Which way is preferred, and why? EDIT: Since user gnat says this question is poorly formed, I'll add that the official python packaging tutorial does not seem to comment on which of the methods described above is the preferred one. I am explicitly not giving my personal list of pros and cons because I'm interested in whether there is a community preferred method, not generating a discussion of pros/cons :)

    Read the article

  • Incorporating libs into module pattern

    - by webnesto
    I have recently started using require.js (along with Backbone.js, jQuery, and a handful of other JavaScript libs) and I love the module pattern (here's a nice synopsis if you're unfamiliar: http://www.adequatelygood.com/2010/3/JavaScript-Module-Pattern-In-Depth). Something I'm running up against is best practices on incorporating libs that don't (out of the box) support the module pattern. For example, jQuery without modification is going to load into a global jQuery variable and that's that. Require.js recognizes this and provides an example project for download with a (slightly) modified version of jQuery to incorporate with a require.js project. This goes against everything I've ever learned about using external libs - never modify the source. I can list a ton of reasons. Regardless, this is not an approach I'm comfortable with. I have been using a mixed approach - wherein I build/load the "traditional" JS libraries in a "traditional" way (available in the global namespace) and then using the module pattern for all of my application code. This seems okay to me, but it bugs me because one of the real beauties of the module pattern (no globals) is getting perverted. Anyone else got a better solution to this problem?

    Read the article

  • 'module' object has no attribute 'element_make_factory'

    - by Ronan Dejhero
    i have this code : import pygst import st, pygtk player_name = gst.element_make_factory("playbin", "Multimedia Player") player_name.set_property("uri", "../media/alert.mp3") player_name.set_state(gst.PLAYING) it keeps throwing me the following error : player_name = gst.element_make_factory("playbin", "Multimedia Player") AttributeError: 'module' object has no attribute 'element_make_factory' nay way to solve this and why is this happening ? if i print gst i get the following : <module 'gst' from '/usr/lib/python2.7/dist-packages/gst-0.10/gst/__init__.pyc'> so it is a module !

    Read the article

  • The DotNetNuke Gallery Module - 7 Video Tutorials

    In this video tutorial we cover the Installation of the DotNetNuke Core Gallery Module and show you how to configure it correctly.We walk you through how to use all of the features in the Gallery module including creating albums, uploading files, bulk uploads, the slideshow, media files, watermarks, templates, and more.The videos contain:Video 1 - Introduction to the DNNGallery Module, Installation and Basic ConfigurationVideo 2 -How to Upload Images and Configure Their SettingsVideo 3 -Creating Gallery Albums and Bulk UploadingVideo 4 - How to Add Files and Albums Using FTP, Adding Music and Changing Permissible Upload TypesVideo 5 - How to Add Video Files, How to Rate Files,Gallery Look and FeelVideo 6 - Changing Feature Settings,Adding Watermarks, Gallery Security RolesVideo 7 - Working withPrivate Galleries and Security Roles, Gallery MaintenanceTotal Time Length: 57minsThe DotNetNuke Gallery Module - 7 Video Tutorials Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

    Read the article

  • @staticmethod vs module-level function

    - by darkfeline
    This is not about @staticmethod and @classmethod! I know how staticmethod works. What I want to know is the proper use cases for @staticmethod vs. a module-level function. I've googled this question, and it seems there's some general agreement that module-level functions are preferred over static methods because it's more pythonic. Static methods have the advantage of being bound to its class, which may make sense if only that class uses it. However, in Python functionality is usually organized by module not class, so usually making it a module function makes sense too. Static methods can also be overridden by subclasses, which is an advantage or disadvantage depending on how you look at it. Although, static methods are usually "functionally pure" so overriding it may not be smart, but it may be convenient sometimes (though this may be one of those "convenient, but NEVER DO IT" kind of things only experience can teach you). Are there any general rule-of-thumbs for using either staticmethod or module-level functions? What concrete advantages or disadvantages do they have (e.g. future extension, external extension, readability)? If possible, also provide a case example.

    Read the article

  • Javascript Module pattern with DOM ready

    - by dego89
    I am writing a JS Module pattern to test out code and help me understand the pattern, using a JS Fiddle. What I can't figure out is why my "private methods" on line 25 and 26, when referenced via DOM ready, have a value of undefined. JSFiddle Code Sample: var obj = { key: "value" }; var Module = (function () { var innerVar = "5"; console.log("obj var in Module:"); console.log(obj); function privateFunction() { console.log("privateFunction() called."); innerFunction(); function innerFunction() { console.log("inner function of (private function) called."); } } function _numTwo() { console.log("_numTwo() function called."); } return { test: privateFunction, numTwo: _numTwo } }(obj)); $(document).ready(function () { console.log("$ Dom Ready"); console.log("Module in Dom Ready: "); console.log(Module.test()); });

    Read the article

  • How to debug problems in Linux kernel module `init()`?

    - by Kimvais
    I am using remote (k)gdb to debug a problem in a module that causes a panic when loaded e.g. when init() is called. The stack trace just shows that do_one_initcall(mod->init) causes the crash. In order to get the symbol file loaded in the gdb, I need to get the address of the module text section, and to get that I need to get the module loaded. Because the insmod in busybox (1.16.1) doesn't support -m so I'm stuck to grep modulename /proc/modules + adding the offset from nm to figure out the address. So I'm facing a sort a of a chicken and an egg problem here - to be able to debug the module loading, I need to get the module loaded - but in order to get the module loaded, I need to debug the problem... So I am currently thinking about two options - is there a way to get the address information either: by printk() in the module init code by printk() somewhere in the kernel code all this prior to calling the mod->init() - so I could place a breakpoint there, load the symbol file, hit c and see it crash and burn...

    Read the article

  • How do I call setattr() on the current module?

    - by Matt Joiner
    What do I pass as the first parameter "object" to the function setattr(object, name, value), to set variables on the current module? For example: setattr(object, "SOME_CONSTANT", 42); giving the same effect as: SOME_CONSTANT = 42 within the module containing these lines (with the correct object). I'm generate several values at the module level dynamically, and as I can't define __getattr__ at the module level, this is my fallback.

    Read the article

  • Can't install Perl DBD module on Ubuntu (for Bugzilla)

    - by Mara
    Trying to install bugzilla-4.2.2 on Ubuntu 12.04. When I run checksetup.pl I get the following error: YOU MUST RUN ONE OF THE FOLLOWING COMMANDS (depending on which database you use): PostgreSQL: /usr/bin/perl install-module.pl DBD::Pg MySQL: /usr/bin/perl install-module.pl DBD::mysql SQLite: /usr/bin/perl install-module.pl DBD::SQLite Oracle: /usr/bin/perl install-module.pl DBD::Oracle To attempt an automatic install of every required and optional module with one command, do: /usr/bin/perl install-module.pl --all I have installed MySQL via XAMPP so I run: /urs/bin/perl install-module.pl DBD::mysql And get the following error: perl Makefile.PL --testuser=username Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Can't exec "mysql_config": No such file or directory at Makefile.PL line 479. Can't find mysql_config. Use --mysql_config option to specify where mysql_config is located Failed to determine directory of mysql.h. Use perl Makefile.PL --cflags=-I<dir> to set this directory. For details see the INSTALL.html file, section "C Compiler flags" or type perl Makefile.PL --help Warning: No success on command[/usr/bin/perl Makefile.PL LIB="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib" INSTALLMAN1DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man1" INSTALLMAN3DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man3" INSTALLBIN="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLSCRIPT="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLDIRS=perl] CAPTTOFU/DBD-mysql-4.021.tar.gz /usr/bin/perl Makefile.PL LIB="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib" INSTALLMAN1DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man1" INSTALLMAN3DIR="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/man/man3" INSTALLBIN="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLSCRIPT="/opt/lampp/htdocs/bugzilla/4.2.2/bugzilla-4.2.2/lib/bin" INSTALLDIRS=perl -- NOT OK Skipping test because of notest pragma Running make install Make had some problems, won't install Could not read metadata file. Falling back to other methods to determine prerequisites So then I tried checksetup.pl's suggestion and ran: /usr/bin/perl install-module.pl --all And it seems to have installed DBD::SQLite without any problems, but again I see a warning that says it's skipping tests because of notest pragma. When I re-run checksetup.pl It shows 3 of the 4 original DB drivers in the "not found" list: PostgreSQL: /usr/bin/perl install-module.pl DBD::Pg MySQL: /usr/bin/perl install-module.pl DBD::mysql Oracle: /usr/bin/perl install-module.pl DBD::Oracle So running it with --all seems to have installed the SQLite driver without any problems, but for some reason I can't seem to install the MySQL driver. Again I need MySQL because thats what XAMPP uses and because I prefer MySQL regardless. I have a feeling it has something to do with this notest pragma error. Any ideas? Thanks in advance!

    Read the article

  • How to restore a hidden loadable kernel module from /sys/module and dealing with restoring holders_dir?

    - by user1833005
    I'm playing with kernel module hiding on Linux Kernel 3.x. I try to hide and recover the module from /sys/module. Everything works fine on Kernel Version 3.0 and 3.2.6, I can load and unload the module and hide and unhide it. When I'm unloading the module on kernel 3.6.6 I get the following error: rmmod: ERROR: could not open '/sys/module/xxx/holders': No such file or directory rmmod: ERROR: Module xxx is in use Has anybody an idea how I could restore of the module so that I am able to unload it without errors? Here is my code: /* hide from /sys/module */ kobject_del(&__this_module.mkobj.kobj); list_del(&__this_module.mkobj.kobj.entry); /* add to /sys/module */ kobject_add(&__this_module.mkobj.kobj,__this_module.mkobj.kobj.parent,"xxx"); Thank you four help :)

    Read the article

  • vmware network installation problem

    - by shantanu
    After installation from vmware_bunddle it shows network device error during configuration(First run). Log File: 2012-04-03T20:01:24.881+06:00| vthread-3| I120: Log for VMware Workstation pid=5766 version=8.0.2 build=build-591240 option=Release 2012-04-03T20:01:24.881+06:00| vthread-3| I120: The process is 64-bit. 2012-04-03T20:01:24.881+06:00| vthread-3| I120: Host codepage=UTF-8 encoding=UTF-8 2012-04-03T20:01:24.881+06:00| vthread-3| I120: Host is Linux 3.2.0-19-generic Ubuntu precise (development branch) 2012-04-03T20:01:24.880+06:00| vthread-3| I120: Msg_Reset: 2012-04-03T20:01:24.880+06:00| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/usr/lib/vmware/settings": No such file or directory. 2012-04-03T20:01:24.880+06:00| vthread-3| I120: ---------------------------------------- 2012-04-03T20:01:24.880+06:00| vthread-3| I120: PREF Optional preferences file not found at /usr/lib/vmware/settings. Using default values. 2012-04-03T20:01:24.880+06:00| vthread-3| I120: Msg_Reset: 2012-04-03T20:01:24.880+06:00| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/root/.vmware/config": No such file or directory. 2012-04-03T20:01:24.880+06:00| vthread-3| I120: ---------------------------------------- 2012-04-03T20:01:24.880+06:00| vthread-3| I120: PREF Optional preferences file not found at /root/.vmware/config. Using default values. 2012-04-03T20:01:24.880+06:00| vthread-3| I120: Msg_Reset: 2012-04-03T20:01:24.880+06:00| vthread-3| I120: [msg.dictionary.load.openFailed] Cannot open file "/root/.vmware/preferences": No such file or directory. 2012-04-03T20:01:24.880+06:00| vthread-3| I120: ---------------------------------------- 2012-04-03T20:01:24.881+06:00| vthread-3| I120: PREF Failed to load user preferences. 2012-04-03T20:01:24.881+06:00| vthread-3| W110: Logging to /tmp/vmware-root/modconfig-5766.log 2012-04-03T20:01:25.200+06:00| vthread-3| I120: modconf query interface initialized 2012-04-03T20:01:25.201+06:00| vthread-3| I120: modconf library initialized 2012-04-03T20:01:25.269+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.278+06:00| vthread-3| I120: Validating path /lib/modules/preferred/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:25.278+06:00| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-04-03T20:01:25.278+06:00| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h not found. 2012-04-03T20:01:25.278+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:25.284+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.306+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.355+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:01:25.355+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:25.362+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.383+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.434+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:01:25.502+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.507+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.511+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.516+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.521+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.561+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.566+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.571+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.576+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.581+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.586+06:00| vthread-3| I120: Validating path /lib/modules/preferred/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:25.586+06:00| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-04-03T20:01:25.586+06:00| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h not found. 2012-04-03T20:01:25.586+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:25.593+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.614+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.663+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:01:25.740+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.747+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.752+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.757+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.762+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:25.767+06:00| vthread-3| I120: Validating path /lib/modules/preferred/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:25.767+06:00| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-04-03T20:01:25.767+06:00| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h not found. 2012-04-03T20:01:25.767+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:25.772+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.792+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:25.843+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:01:26.838+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:26.848+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:26.853+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:26.858+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:26.863+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:28.460+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:28.460+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:28.466+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:28.488+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:28.542+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:01:28.542+06:00| vthread-3| I120: Building module vmmon. 2012-04-03T20:01:28.553+06:00| vthread-3| I120: Extracting the sources of the vmmon module. 2012-04-03T20:01:28.615+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmmon-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:01:36.499+06:00| vthread-3| I120: Installing module vmmon from /tmp/vmware-root/modules/vmmon.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:01:36.507+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vmmon.ko 2012-04-03T20:01:58.314+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:01:58.315+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:01:58.336+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:58.379+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:01:58.431+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:01:58.431+06:00| vthread-3| I120: Building module vmnet. 2012-04-03T20:01:58.431+06:00| vthread-3| I120: Extracting the sources of the vmnet module. 2012-04-03T20:01:58.541+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmnet-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:02:05.973+06:00| vthread-3| I120: Failed to compile module vmnet! 2012-04-03T20:02:05.984+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:02:05.984+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:02:05.990+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:02:06.015+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:02:06.067+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:02:06.067+06:00| vthread-3| I120: Building module vmblock. 2012-04-03T20:02:06.067+06:00| vthread-3| I120: Extracting the sources of the vmblock module. 2012-04-03T20:02:06.141+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmblock-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:02:13.531+06:00| vthread-3| I120: Installing module vmblock from /tmp/vmware-root/modules/vmblock.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:02:13.532+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vmblock.ko 2012-04-03T20:02:19.090+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:02:19.090+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:02:19.097+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:02:19.117+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:02:19.173+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:02:19.173+06:00| vthread-3| I120: Building module vmci. 2012-04-03T20:02:19.174+06:00| vthread-3| I120: Extracting the sources of the vmci module. 2012-04-03T20:02:19.284+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmci-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:02:28.525+06:00| vthread-3| I120: Installing module vmci from /tmp/vmware-root/modules/vmci.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:02:28.526+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vmci.ko 2012-04-03T20:02:31.760+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:02:31.760+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:02:31.766+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:02:31.786+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:02:31.838+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:02:31.838+06:00| vthread-3| I120: Building module vmci. 2012-04-03T20:02:31.839+06:00| vthread-3| I120: Extracting the sources of the vmci module. 2012-04-03T20:02:31.864+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmci-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:02:33.684+06:00| vthread-3| I120: Building module vsock. 2012-04-03T20:02:33.685+06:00| vthread-3| I120: Extracting the sources of the vsock module. 2012-04-03T20:02:33.809+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vsock-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:02:41.050+06:00| vthread-3| I120: Installing module vsock from /tmp/vmware-root/modules/vsock.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:02:41.051+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vsock.ko 2012-04-03T20:03:02.757+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.762+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.767+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.771+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.776+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.782+06:00| vthread-3| I120: Validating path /lib/modules/preferred/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:03:02.782+06:00| vthread-3| I120: Failed to find /lib/modules/preferred/build/include/linux/version.h 2012-04-03T20:03:02.782+06:00| vthread-3| I120: Failed version test: /lib/modules/preferred/build/include/linux/version.h not found. 2012-04-03T20:03:02.782+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:03:02.790+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:02.814+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:02.865+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:03:02.958+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.968+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.973+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.978+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:02.983+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:04.372+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:04.372+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:03:04.378+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:04.399+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:04.452+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:03:04.452+06:00| vthread-3| I120: Building module vmmon. 2012-04-03T20:03:04.452+06:00| vthread-3| I120: Extracting the sources of the vmmon module. 2012-04-03T20:03:04.486+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmmon-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:03:05.976+06:00| vthread-3| I120: Installing module vmmon from /tmp/vmware-root/modules/vmmon.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:03:05.977+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vmmon.ko 2012-04-03T20:03:09.056+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:09.057+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:03:09.065+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:09.090+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:09.142+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:03:09.142+06:00| vthread-3| I120: Building module vmnet. 2012-04-03T20:03:09.142+06:00| vthread-3| I120: Extracting the sources of the vmnet module. 2012-04-03T20:03:09.169+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmnet-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:03:12.072+06:00| vthread-3| I120: Failed to compile module vmnet! 2012-04-03T20:03:12.090+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:12.090+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:03:12.098+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:12.121+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:12.179+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:03:12.179+06:00| vthread-3| I120: Building module vmblock. 2012-04-03T20:03:12.179+06:00| vthread-3| I120: Extracting the sources of the vmblock module. 2012-04-03T20:03:12.205+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmblock-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:03:15.340+06:00| vthread-3| I120: Installing module vmblock from /tmp/vmware-root/modules/vmblock.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:03:15.341+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vmblock.ko 2012-04-03T20:03:18.451+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:18.451+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:03:18.457+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:18.480+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:18.531+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:03:18.531+06:00| vthread-3| I120: Building module vmci. 2012-04-03T20:03:18.531+06:00| vthread-3| I120: Extracting the sources of the vmci module. 2012-04-03T20:03:18.569+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmci-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:03:19.787+06:00| vthread-3| I120: Installing module vmci from /tmp/vmware-root/modules/vmci.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:03:19.789+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vmci.ko 2012-04-03T20:03:22.933+06:00| vthread-3| I120: Trying to find a suitable PBM set for kernel 3.2.0-19-generic. 2012-04-03T20:03:22.933+06:00| vthread-3| I120: Validating path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic 2012-04-03T20:03:22.939+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:22.959+06:00| vthread-3| I120: Your GCC version: 4.6 2012-04-03T20:03:23.009+06:00| vthread-3| I120: Header path /lib/modules/3.2.0-19-generic/build/include for kernel release 3.2.0-19-generic is valid. 2012-04-03T20:03:23.009+06:00| vthread-3| I120: Building module vmci. 2012-04-03T20:03:23.009+06:00| vthread-3| I120: Extracting the sources of the vmci module. 2012-04-03T20:03:23.034+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vmci-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:03:24.227+06:00| vthread-3| I120: Building module vsock. 2012-04-03T20:03:24.227+06:00| vthread-3| I120: Extracting the sources of the vsock module. 2012-04-03T20:03:24.254+06:00| vthread-3| I120: Building module with command: /usr/bin/make -j -C /tmp/vmware-root/modules/vsock-only auto-build SUPPORT_SMP=1 HEADER_DIR=/lib/modules/3.2.0-19-generic/build/include CC=/usr/bin/gcc GREP=/usr/bin/make IS_GCC_3=no VMCCVER=4.6 2012-04-03T20:03:26.125+06:00| vthread-3| I120: Installing module vsock from /tmp/vmware-root/modules/vsock.o to /lib/modules/3.2.0-19-generic/misc. 2012-04-03T20:03:26.126+06:00| vthread-3| I120: Registering file: /usr/lib/vmware-installer/2.0/vmware-installer --register-file vmware-vmx regular /lib/modules/3.2.0-19-generic/misc/vsock.ko My System details: cpu : AMD APU dual core E450 ram: 2GB ubuntu: 12.04 (64 bit) I have downloaded Latest vmware version. Thanks in advance

    Read the article

  • Zenoss No space left on device Error

    - by Pastelinux
    Site Error An error was encountered while publishing this resource. Sorry, a site error occurred. Traceback (innermost last): Module ZPublisher.Publish, line 231, in publish_module_standard Module ZPublisher.Publish, line 165, in publish Module Zope2.App.startup, line 211, in __call__ Module Products.ZenUI3.browser, line 105, in __call__ Module Products.Five.browser.pagetemplatefile, line 60, in __call__ Module zope.pagetemplate.pagetemplate, line 115, in pt_render Module zope.tal.talinterpreter, line 271, in __call__ Module zope.tal.talinterpreter, line 343, in interpret Module zope.tal.talinterpreter, line 858, in do_defineMacro Module zope.tal.talinterpreter, line 343, in interpret Module zope.tal.talinterpreter, line 533, in do_optTag_tal Module zope.tal.talinterpreter, line 518, in do_optTag Module zope.tal.talinterpreter, line 513, in no_tag Module zope.tal.talinterpreter, line 343, in interpret Module zope.tal.talinterpreter, line 620, in do_insertText_tal Module Products.PageTemplates.Expressions, line 203, in evaluateText Module Products.PageTemplates.Expressions, line 222, in _handleText Module zope.component._api, line 174, in queryUtility Module zope.component.registry, line 165, in queryUtility Module ZODB.Connection, line 834, in setstate Module ZODB.Connection, line 884, in _setstate Module ZEO.ClientStorage, line 815, in load Module ZEO.cache, line 143, in call Module ZEO.cache, line 607, in store IOError: [Errno 28] No space left on device Went in to check my server through zenoss today and it looks like somehow my server is full. Which when i look at my server its only 85% full: unclebob:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/unclebob--vg0-unclebob--root 1.9G 1.5G 335M 82% / tmpfs 471M 0 471M 0% /lib/init/rw udev 10M 820K 9.2M 9% /dev tmpfs 471M 0 471M 0% /dev/shm overflow 1.0M 1.0M 0 100% /tmp /dev/hde1 942M 36M 859M 5% /boot unclebob:/tmp# df -i Filesystem Inodes IUsed IFree IUse% Mounted on /dev/mapper/unclebob--vg0-unclebob--root 121920 54844 67076 45% / tmpfs 120489 3 120486 1% /lib/init/rw udev 120489 1520 118969 2% /dev tmpfs 120489 1 120488 1% /dev/shm overflow 120489 14 120475 1% /tmp /dev/hde1 61312 33 61279 1% /boot It looks like theres these two files: .ICE-unix/ .X11-unix/ They had been hidden. I'll remove those. Any idea upon what they maybe? Any ideas on a fix? Probably has something to do with Zenoss

    Read the article

  • Problem with installing sqlite3 module for python 2.6 on an ubuntu system

    - by Hoang
    I need to run the sqlite3 module on python 2.6 in an ubuntu system. How do I install this module for Python 2.6? Somehow I don't have this module, it raises the error: >>> import sqlite3 Traceback (most recent call last): File "<stdin>", line 1, in <module> File "/usr/local/lib/python2.6/sqlite3/__init__.py", line 24, in <module> from dbapi2 import * File "/usr/local/lib/python2.6/sqlite3/dbapi2.py", line 27, in <module> from _sqlite3 import * ImportError: No module named _sqlite3

    Read the article

  • Unable to Install VirtualBox Due to Missing Kernel Module

    - by SoftTimur
    I am trying to install VirtualBox on my Ubuntu. I first tried to sudo apt-get install virtualbox-ose in a terminal, but after the configuration step, it fails with an error: No suitable module for running kernel found When proceeding with starting virtualbox, I get this error: WARNING: The character device /dev/vboxdrv does not exist. Please install the virtualbox-ose-dkms package and the appropriate headers, most likely linux-headers-generic. You will not be able to start VMs until this problem is fixed. So I tried the package from http://www.virtualbox.org/, but starting VirtualBox fails with: WARNING: The vboxdrv kernel module is not loaded. Either there is no module available for the current kernel (2.6.38-8-generic-pae) or it failed to load. Please recompile the kernel module and install it by sudo /etc/init.d/vboxdrv setup You will not be able to start VMs until this problem is fixed. So I ran sudo /etc/init.d/vboxdrv setup, but it fails too: * Stopping VirtualBox kernel modules [ OK ] * Uninstalling old VirtualBox DKMS kernel modules [ OK ] * Trying to register the VirtualBox kernel modules using DKMS Error! Your kernel headers for kernel 2.6.38-8-generic-pae cannot be found at /lib/modules/2.6.38-8-generic-pae/build or /lib/modules/2.6.38-8-generic-pae/source. * Failed, trying without DKMS * Recompiling VirtualBox kernel modules * Look at /var/log/vbox-install.log to find out what went wrong The contents of /var/log/vbox-install.log. As I am stuck, I also tried to install kernel-devel with yum, still fruitless: root@ubuntu# yum install kernel-devel Setting up Install Process No package kernel-devel available. Nothing to do Now I've no idea how to correct this. Any ideas?

    Read the article

  • VMware Kernel Module Updater hangs on Ubuntu 13.04

    VMware Player has a nice auto-detection of kernel changes, and requests the user to compile the required modules in order to load them. This happens from time to time after a regular update of your system. Usually, the dialog of VMware Kernel Module Updater pops up, asks for root access authentication, and completes the compilation. VMware Player or Workstation checks if modules for the active kernel are available. In theory this is supposed to work flawlessly but in reality there are pitfalls occassionally. With the recent upgrade to Ubuntu 13.04 Raring Ringtail and the latest kernel 3.8.0-21 the actual VMware Kernel Module Updater simply disappeared and the application wouldn't start as expected. When you launch VMware Player as super user (root) the dialog would stall like so: VMware Kernel Module Updater stalls while stopping the services Prior to version 5.x of VMware Player or version 7.x of VMware Workstation you would run a command like: $ sudo vmware-config.pl to resolve the module version conflict but this doesn't work anyway. Solution Instead, you have to execute the following line in a terminal or console window: $ sudo vmware-modconfig --console --install-all Those switches are (as of writing this article) not documented in the output of the --help switch. But VMware already documented this procedure in their knowledge base: VMware Workstation stops functioning after updating the kernel on a Linux host (1002411). Update As of today I had the first kernel upgrade to version 3.8.0-22 in Ubuntu 13.04. Don't even try it without vmware-modconfig...

    Read the article

  • Changing the Module title in DotNetNuke on the Fly

    - by grant.barrington
    This is an extremely short post, buy hopefully it will help others in the situation. (Also if I need to find it again I know where to look) We have recently completed a project using DotNetNuke as our base. The project was for a B2B portal using Microsoft Dynamics NAV as our back-end. We had a requirement where we wanted to change the title of a Module on the fly. This ended up being pretty easy from our module. In our Page_Load event all we had to do was the following. Control ctl = DotNetNuke.Common.Globals.FindControlRecursiveDown(this.ContainerControl, "lblTitle"); if ((ctl != null)) { ((Label)ctl).Text += "- Text Added"; } Thats it. All we do it go up 1 control (this.ContainerControl) and look for the Label called "lblTitle". We then append text to the existing Module title.

    Read the article

  • ImportError: No module named gtk

    - by Rick_2047
    after the debacle a few hours back I managed to get a working desktop after using an ethernet cable and sudo apt-get install ubuntu-desktop But now when I try to run ubuntu software center from CLI this is what I get rick@Abigail:~$ sudo software-center Traceback (most recent call last): File "/usr/bin/software-center", line 34, in <module> import gtk ImportError: No module named gtk Any guesses how to fix this. The search box on synaptic is also missing. It has something to do with module named axi. I think the both are related.

    Read the article

  • A bacon- (and module-) saving PowerShell incident

    - by AaronBertrand
    Earlier today I made a big goof. I opened a module in Notepad, intending to use it as the basis for a new module. I was in the process of using "File > Save As" when my phone rang just at the precise instant that, for some reason, made me click on "File > Save" by mistake. After hitting Ctrl+Z 30 times to try to get the old version of the module back, I remembered that Notepad has never had more than one level of Undo. Back when I was coding ASP by hand, I was very well aware of this, but I...(read more)

    Read the article

  • A bacon- (and module-) saving PowerShell incident

    - by AaronBertrand
    Earlier today I made a big goof. I opened a module in Notepad, intending to use it as the basis for a new module. I was in the process of using "File > Save As" when my phone rang just at the precise instant that, for some reason, made me click on "File > Save" by mistake. After hitting Ctrl+Z 30 times to try to get the old version of the module back, I remembered that Notepad has never had more than one level of Undo. Back when I was coding ASP by hand, I was very well aware of this, but I...(read more)

    Read the article

  • DotNetNuke Gallery Module - 7 Videos

    In this tutorial we cover the Installation of the DotNetNuke Core Gallery Module and show you how to configure it correctly. We walk you through how to use all of the features in the Gallery module including creating albums, uploading files, bulk uploads, the slideshow, media files, watermarks, templates, and more. The videos contain: Video 1 - Introduction to the DNN Gallery Module, Installation and Basic Configuration Video 2 - How to Upload Images and Configure Their Settings Video 3 - Creating Gallery Albums and Bulk Uploading Video 4 - How to Add Files and Albums Using FTP, Adding Music and Changing Permissible Upload Types Video 5 - How to Add Video Files, How to Rate Files, Gallery Look and Feel Video 6 - Changing Feature Settings, Adding Watermarks, Gallery Security Roles Video 7 - Working with Private Galleries and Security Roles, Gallery Maintenance Total Time Length: 57minsDid you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

    Read the article

  • Disabling eth0 Module on a Macbook Aluminum

    - by user115488
    The Ubuntu page for my device states the following at the bottom (Known Issues) PowerTOP reports that the module for the 10/100/1000 interface wakes the processor 100+x/sec, accounting for 50% of wakeups on an idle system. This dramatically shortens battery life. One potential solution is to unload this module if you only use wireless. I only use wireless, but I could not find instructions to "unload the module". I have a feeling if I try something related to this, but not the same, battery life will not improve and my eth0 won't work. Anyone have a good guide on this?

    Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >