Search Results

Search found 416 results on 17 pages for 'redundancy'.

Page 8/17 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• ML 350 additional SATA RAID controller (mirror only)

  - by Nicholas

  I have a Proliant ML350 G8 with two SAS raid arrays currently set up - thereby maxing the default P420i raid controller. I need to set up a large video dump space in addition to this existing set-up (for non backed up, non-critical, temporary storage). I had planned to just add a 2TB SATA disk and plug it into the motherboard. However I it occurred to me the motherboard might have built-in mirror RAID support? Therefore I could use two SATA disks and have some semblance of redundancy. Is this possible? Or would I need to get a cheap raid card? Any recommendations?

  Read the article

• All nework interfaces hang for seconds while one interface goes up/down

  - by user3698377

  I am building a client/server application that uses several network interfaces in parallel for redundancy, and I have noticed that while one network interface goes down or goes up, the communication on other interfaces hangs for several seconds. I could reproduce this behavior without my application in a simple way: there are 2 interfaces available on computer 1 ( Ethernet and WiFi ) ping from computer 2 the IP address of the Ethernet connection of computer 1 disconnect the WiFi of computer 1 ping hangs for seconds, and then the packets are traveling again between the 2 computers. The hanging happens as well if I turn back on the WiFi connection on computer 1. It happens as well if I ping the WiFi IP, and turn off/on the Ethernet connection ( or unplug/plug the cable). I am using Linux Ubuntu 12.04 on both computers. Any ideas why is this happening, and if / how can it be avoided?

  Read the article

• configure cisco catalyst 3560g with an egress uplink

  - by imaginative

  Currently my setup has our egress uplink connected directly to an external interface on a linux router/firewall/nat gateway. Since the linux box is a single point of failure, I've since setup two openbsd boxes using carp+pf+pfsync in order to gain some additional redundancy. the problem is, I only have one egress uplink (it's still a single point of failure) but need to get it to speak to the active carp node in my openbsd cluster which will server as my new router/firewall/nat cluster. Is there anything specific I need to do on a 3560G in order for me to be able to: 1) Drop the egress uplink into a port 2) Drop one link from the switch to a firewall 2) Drop a second link from a switch to the firewall This is so if one box dies, the other still has the egress link to the switch. Is putting them into one VLAN enough? Anything else that needs to go into the configuration for this setup to work?

  Read the article

• Using 2 Transparent HAProxy for load balancing

  - by Nyxynyx

  We can configure HAProxy to be a transparent proxy by using the guide here, where one of the steps says ...to put the backend servers in a different subnet to the front end clients and make sure that the default gateway points back at the HAProxy load balancer. However when we need to have 2 transparent HAProxy in front of our balanced servers (for redundancy), it seems like this wont work as we can only set one gateway for our balanced servers. What will be the correct way to setup the system such that we can have 2 transparent HAProxy infront of the balanced servers? The main reason for having transparent proxies is the need to find the client's IP addresses over TCP.

  Read the article

• Is span monitoring on Cisco ASA 5520 possible?

  - by Brent

  From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

  Read the article

• IOMEGA 500GB hard disk data reccovery

  - by Vineeth

  Last year by November I bought an IOMEGA 500GB Prestige hard disk. Yesterday, unfortunately the hard disk fell down from my table. After that incident, when I connect my disk, Windows asks me to format the disk to use, but I didn't format it yet. Actually, on that hard disk I have about 320GB of data. I tried all my possible ways to access my disk. I tried using DOS. It shows "data error (Cyclic redundancy check)". I have a 3 year warranty. Will I be covered under warranty if I report this issue to IOMEGA? Can I get my data back?

  Read the article

• Non-Apple RAID card for Mac PRO (TOWER)

  - by Arthor

  I have the following: MAC PRO (Model Number: A1186) (PCIe - SLOTS) At present I am using the software RAID however I wish to move to the hardware raid because of the following: Performance (4 x 300gb SATA II in RAID 5) Redundancy (Raid 5, 1 drive can fail and system will be online) I do not wish to use the Apple RAID card (very expensive), I would like to use an aftermarket one which is cheaper. Questions: Does anyone have a WORKING aftermarket RAID card working in their MAC PRO (TOWER)? -(Have done some research, ROCKETRAID, need confirmation) If so to the above, does it work from boot? Thanks

  Read the article

• Best way to grow Linux software RAID 1 to RAID 10

  - by Hans Malherbe

  mdadm does not seem to support growing an array from level 1 to level 10. I have two disks in RAID 1. I want to add two new disks and convert the array to a four disk RAID 10 array. My current strategy: Make good backup. Create a degraded 4 disk RAID 10 array with two missing disks. rsync the RAID 1 array with the RAID 10 array. fail and remove one disk from the RAID 1 array. Add the available disk to the RAID 10 array and wait for resynch to complete. Destroy the RAID 1 array and add the last disk to the RAID 10 array. The problem is the lack of redundancy at step 5. Is there a better way?

  Read the article

• NIC bonding with two uplinks

  - by Karolis T.

  Is bonding the preferred way of implementing ISP redundancy? In the texts I've seen, bond device has a netmask, gateway of it's own. How can this be obtained if there are two different gateways from two uplinks, which one to choose? Do I need any special routing rules to go with it or does simply configuring separate interfaces (using Debian, /etc/network/interfaces), i.e eth1, eth2 for their corresponding uplinks and bonding them to bond0 handle routing automatically? If I want to NAT client machines, do they use bond device's IP as a gateway? Does the bond0 device is the device that goes into iptables nat rules? Thanks

  Read the article

• Creating an office network and monitoring all activity without a proxy

  - by Robert

  We are setting up our office network and would like to track all the websites visited by our employees. However, we would not like to use any proxy based solutions. Our work is highly dependent on applications in which you cannot configure a proxy. Hence, the approach we would like to follow is setting up a router inside a computer (something like this : http://www.techrepublic.com/article/configure-windows-server-2003-to-act-as-a-router/5844624) This will also allow us to attach multiple ethernet cards and have redundancy in internet connectivity with complete abstraction from the user about which connection is being used. But most importantly, since all the traffic will be going through the computer (configured as a router) I assume there will be a way to run packet analysis on all the request / responses being made. For example, list all the FTP servers connected to (port 21), give a graph of all the URLs visited per day by frequency. Is there already a software which does this ? Or is it possible to build something like this ?

  Read the article

• Best way to grow Linux software RAID 1 to RAID 10

  - by Hans Malherbe

  mdadm does not seem to support growing an array from level 1 to level 10. I have two disks in RAID 1. I want to add two new disks and convert the array to a four disk RAID 10 array. My current strategy: Make good backup. Create a degraded 4 disk RAID 10 array with two missing disks. rsync the RAID 1 array with the RAID 10 array. fail and remove one disk from the RAID 1 array. Add the available disk to the RAID 10 array and wait for resynch to complete. Destroy the RAID 1 array and add the last disk to the RAID 10 array. The problem is the lack of redundancy at step 5. Is there a better way?

  Read the article

• What does this WinImage Error Mean?

  - by Kryten

  Hi, I am using WinImage (version 8.0) on Windows XP SP3 to create a VHD File from my Hard Drive, however, everytime I try to, everytime it says: "I/O error in reading data on position 000000007cd40000:00010000. Error 23: Data Error (cyclic redundancy check)." with the options "Abort", "Retry", "Skip" & "Skip All". Everytime I try "Retry" the message comes, if I click skip another message comes up (same as above, except the data position). I have run "CHKDSK /F /R" several times, but the error always appears. What is wrong? Can I safely skip the Errors? Is there anything I can do to fix the error?

  Read the article

• Win2008 DC in a Windows 2000 domain: can I keep the old DC?

  - by gravyface

  Will be putting a new Windows 2008 SE Server into a single domain network with two domain controllers, both running Windows 2000 Server. The functional level of the domain is mixed mode/2000. Until a second 2008 DC can be purchased, I'd like to leave the current Win2k operational master DC as a backup DC as the other member servers running 2003 have either accounting/SQL or Exchange on them. Eventually all the w2k servers will be decommissioned, but until then, I need another DC for redundancy. Following the standard process for adding a new DC, can I leave the old operational master DC (or the other backup DC) running after I transfer the FSMO roles to the new server? Will this cause any issues?

  Read the article

• A simple Volume Replication Tool for large data set?

  - by Jin

  I'm looking for a solution to the following: Server A (Site A) - Win 2008 R2 - approx 10TB (15TB max) of data - well over 8 million files Server B (Site B) - Win 2008 R2 I want to assynchronously replicate Server A's volume to a volume on Server B for data redundancy. Something that I can say to my users, "go here for data" when/if Server A goes belly up due to machine problems, disaster, etc. Windows 2008 R2 does have DFS, but microsoft does not apparently support this large of a dataset (or more accurately, more than 8 million files - according to the docs I could find). I also looked at Veritas Volume Replication, but this seems almost too much as I would also require Veritas Volume Manager. There are numerous "back-up" software which makes a 1-1 backup, which would be ok, but since it will be transfering over internet, I'd like something that has compression during transfer like DFS has. Does anyone have any suggestions regarding this?

  Read the article

• Distributed, Parallel, Fault-tolerant File System

  - by Eddified

  There are so many choices that it's hard to know where to start. My requirements are these: Runs on Linux Most of the files will be between 5-9 MB in size. There will also be a significant number of small-ish jpgs (100px x 100px). All of the files need to be available over http. Redundancy -- ideally it would provide the space efficiency similar to RAID 5 of 75% (in RAID 5 this would be calculated thus: with 4 identical disks, 25% of the space is used for parity = 75% efficent) Must support several petabytes of data scalable runs on commodity hardware In addition, I look for these qualities, though they are not "requirements": Stable, mature file system Lots of momentum and support etc I would like some input as to which file system works best for the given requirements. Some people at my organization are leaning towards MogileFS, but I'm not convinced of the stability and momentum of that project. GlusterFS and Lustre, based on my limited research, appear to be better supported... Thoughts?

  Read the article

• HP Smart Array; Is it possible to convert Raid1 to Raid0 by dropping a failed drive?

  - by Erik Heppler

  I have a server that was running two 60GB drives as a logical RAID1. At some point the second drive was physically removed and the logical drive has been in "Interim Recovery Mode" for several months now. There's no need for the redundancy of RAID1 on this machine, and I have no intention of replacing the missing drive. If possible I would like to convert the current RAID1 to a single-drive RAID0 by simply dropping the failed drive from the current configuration. I'm only interested in doing this if it can be done in-place. Otherwise I'm perfectly content to leave it in "Interim Recovery Mode" indefinitely.

  Read the article

• Need help. HDD Failed

  - by jiewmeng

  i have a seagate 3.5" 500GB SATA2 HDD that i put in a USB case (vantec) that failed recently. symptoms: at first, it started except that attempts made to browse certain folders resulted in "Data Error (Cyclic Redundancy Check)". then when i tried restarting the hdd, then i got a RAW partition, and windows 7 said i need to format it. i also tried using a desktop to connect to the HDD directly using SATA, windows 7 stuck at "starting windows" for abt half hour b4 i gave up on it. in the BIOS, it seems to detect the HDD model correctly, something like STA3500xxx something like that i also tried using TestDisk as suggested by jaclaz on MSFN and it did not find any partitions what could i do now?

  Read the article

• Too much free space on FreeNAS - ZFS

  - by Guillaume

  I have a FreeNAS server with 3 x 2 To disks in raidz1. I would expect to have about 4 To of space available. When I run zpool list I get: [root@freenas] ~# zpool list NAME SIZE USED AVAIL CAP HEALTH ALTROOT main_volume 5.44T 3.95T 1.49T 72% ONLINE /mnt I was expecting a size of 4 To. Also, used space as reported by zpool list does not match what's reported by du: [root@freenas] ~# du -sh /mnt/main_volume/ 2.6T /mnt/main_volume/ There are quite a few things that I dont yet completely understand about ZFS. But at the moment I am mostly worried that I misconfigured my system and that I dont have any storage redundancy. How can I make sure I did not do an horrible mistake ... For the sake of completeness, here is the output of zpool status: [root@freenas] ~# zpool status pool: main_volume state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM main_volume ONLINE 0 0 0 raidz1 ONLINE 0 0 0 gptid/d8584e45-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 gptid/d8f7df30-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 gptid/d9877cc3-5b8a-11d9-b9ea-5404a6630115 ONLINE 0 0 0 errors: No known data errors

  Read the article

• Plug and Go NAS Storage

  - by graham.reeds

  My wife and I are separating. One of the things we need to extricate is the media we have accumulated over the years. So I am looking for a NAS solution that is a) relatively low-cost, b) reliable and c) easy for a non-geek to use (I don't want to be tech support). All it needs to do is hold our iTunes library, photos, course work and maybe some movies and TV shows that I currently have. She will be connecting via her Netbook. I have seen this thread but the reviews on Amazon aren't particularly favourable. Due to the need for simplicity, WHS and FreeNAS are none-starters. I need redundancy as if a single drive system was to die then she would lose her course work and photos. Is the ReadyNAS the only real solution out there?

  Read the article

• Problem getting video from DVD

  - by mabwi

  I have a DVD that a customer needs me to pull ~5 minutes of video from, and convert it to FLV to play on their website. I downloaded AVS Video Converter and tried to use it to convert the VOB file to FLV, with the thought of editing after, and also tried MPEG. Both times it froze up. I then tried to just copy the file from the DVD to my hard drive, thinking that maybe the disc access was slowing things down too much. I got a "Cyclic redundancy" error from Windows while doing that, and it stopped copying. Is the file corrupted? Is there any better way to get it from the DVD player? I only need 5 minutes of 1.5 hours, so if I can avoid converting the entire thing then editing, that would be awesome Thanks for your help

  Read the article

• How to configure machines in a public subnet with two gateways?

  - by Shtééf

  We have a single public /24 subnet, with a BGP router as the primary gateway. Now I'm interested in configuring a second router for redundancy. How do I deal with multiple gateways on the servers in our public subnet? I found some other questions related to multiple gateways that seem to deal with NAT set-ups. In my situation, the servers all have public routed IP-addresses. So from what I can tell, it doesn't really matter which route incoming or outgoing packets take. But I figure the servers need some way of telling when one of the gateways is down, and route around it? Is this accomplished with protocols such as OSPF? And do I need to deploy this on all my servers?

  Read the article

• How realistic/easy is it to host our own web servers?

  - by morpheous

  It is increasingly looking like we will need to host our own servers, because we need modems physically attached to the server machines. I (think) we will need a T1 line to our office for starters. Dont know what else is involved other than the obvious redundancy and failover requirements. My questions are: Do we really have to do it our selves or can we find a service that allows the modems to be remote as well? If we have to host the servers ourselves, what are the steps (technical and operational) required?

  Read the article

• Windows Mobile deletes my Contacts when deleting a partnership

  - by bitbonk

  Sometimes when I reinstall my PC get a new Work PC or buy a new home PC ,ActiveSync, now the Device Center asks me to delete an existing partnership to setup a partnership with the new PC, since only two partnerships are allowed. When I delete that partnership all contacts that originally came from that partnership get deleted too. How can I prevent that from happening. Do I really always have to remember to frequently backup all my contacts in a safe place? How much redundancy is needed. I hat them on one of my PCs and on my phone.

  Read the article

• Redundant APC UPS units, single server set up

  - by Sholom

  Hi All We have a very simple set up, looking for a very simple (reliable) solution: Setup: One Dell box with redundant power supplies running Windows 2003, plugged into two separate APC SmartUPS 1500 units (USB, no smart cards) on two separate circuits. Solution required: IF (UPS1 = Low) AND (UPS2 = Low) THEN: Shutdown gracefully ELSE: DO NOTHING!! APCUPSD only allowes for one instance (and therefore one UPS) in a windows environment. PowerChute can't do this without using APC Smart Cards which means utilizing our switch, but the switch does not have redundant power supplies, so it will only live for as long as one of the two UPS units. And no, i don't have the budget to buy two smart cards pluse a switch with redundancy ;) Thanks

  Read the article

• RDS Replication across regions

  - by Bryan Migliorisi

  We are using Amazon AWS for our web services but given the recent instabilities in their infrastructure, we are trying to figure out how to run our application across multiple regions for additional redundancy. Ideally, we would run our entire app in a active-active configuration in multiple regions but our main concern is that we are using RDS, which I understand cannot replicate across regions. One possible solution (though we have not tried or proven it would work) would be to do mysqldump or EBS snapshots every hour or so but this would mean that we would be forced to run in an active-passive configuration. Our data would be at most an hour behind. This carries its own issues around data synchronization when we failover and the master comes back up, so its not the best solution. Are there any proven solutions for replicating RDS across regions?

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >