rts - Page 8 - Developer IT

Randomely loosing wireless connexion with Cubuntu 12.04

- by statquant

I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

Read the article

Need help with chronic slow wifi connections

- by mgeorge

I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

Read the article

No Wireless Networks, BCM4313 [duplicate]

- by TalonPlz

This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

Read the article

trying to setup wireless

- by JohnMerlino

I'm trying to set up wireless on vostro 1520 dell laptop, with latest Ubuntu install. Here's the output of some of the commands that I was told to run: lshw -C network viggy@ubuntu:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 03 serial: 00:24:e8:da:84:25 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.2.6 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:47 ioport:3000(size=256) memory:f6004000-f6004fff memory:f6000000-f6003fff memory:f6020000-f603ffff *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0e:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:fa000000-fa003fff *-network DISABLED description: Wireless interface physical id: 1 logical name: wlan0 serial: 0c:60:76:05:ee:74 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-29-generic firmware=N/A multicast=yes wireless=IEEE 802.11bg lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 0e:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) 1a:00.0 FireWire (IEEE 1394): O2 Micro, Inc. Device 10f7 (rev 01) 1a:00.1 SD Host controller: O2 Micro, Inc. Device 8120 (rev 01) 1a:00.2 Mass storage controller: O2 Micro, Inc. Device 8130 (rev 01) iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. At this point in time, I don't have wireless.

Read the article

A* algorithm very slow

- by Amaranth

I have an programming a RTS game (I use XNA with C#). The pathfinding is working fine, except that when it has a lot of node to search in, there is a lag period of one or two seconds, it happens mainly when there is no path to the target destination, since it that situation there is more nodes to explore. I have the same problem when the path is shorter but selected more than 3 units (can't take the same path since the selected units can be in different part of the map). private List<NodeInfo> FindPath(Unit u, NodeInfo start, NodeInfo end) { Map map = GameInfo.GetInstance().GameMap; _nearestToTarget = start; start.MoveCost = 0; Vector2 endPosition = map.getTileByPos(end.X, end.Y).Position; //getTileByPos simply gets the tile in a 2D array with the X and Y indexes start.EstimatedRemainingCost = (int)(endPosition - map.getTileByPos(start.X, start.Y).Position).Length(); start.Parent = null; List<NodeInfo> openedNodes = new List<NodeInfo>(); ; List<NodeInfo> closedNodes = new List<NodeInfo>(); Point[] movements = GetMovements(u.UnitType); openedNodes.Add(start); while (!closedNodes.Contains(end) && openedNodes.Count > 0) { //Loop in nodes to find lowest cost NodeInfo currentNode = FindLowestCostOpenedNode(openedNodes); openedNodes.Remove(currentNode); closedNodes.Add(currentNode); Vector2 previousMouvement; if (currentNode.Parent == null) { previousMouvement = ConvertRotationToDirectionVector(u.Rotation); } else { previousMouvement = map.getTileByPos(currentNode.X, currentNode.Y).Position - map.getTileByPos(currentNode.Parent.X, currentNode.Parent.Y).Position; previousMouvement.Normalize(); } //For each neighbor foreach (Point movement in movements) { Point exploredGridPos = new Point(currentNode.X + movement.X, currentNode.Y + movement.Y); //Checks if valid move and checks if not if closed nodes list if (ValidNavigableNode(u.UnitType, new Point(currentNode.X, currentNode.Y), exploredGridPos) && !closedNodes.Contains(_gridMap[exploredGridPos.Y, exploredGridPos.X])) { NodeInfo exploredNode = _gridMap[exploredGridPos.Y, exploredGridPos.X]; Tile.TileType exploredTerrain = map.getTileByPos(exploredGridPos.X, exploredGridPos.Y).TerrainType; if(openedNodes.Contains(exploredNode)) { int newCost = currentNode.MoveCost + GetMoveCost(previousMouvement, movement, exploredTerrain); if (newCost < exploredNode.MoveCost) { exploredNode.Parent = currentNode; exploredNode.MoveCost = newCost; //Find nearest tile to the target (in case doesn't find path to target) //Only compares the node to the current nearest FindNearest(exploredNode); } } else { exploredNode.Parent = currentNode; exploredNode.MoveCost = currentNode.MoveCost + GetMoveCost(previousMouvement, movement, exploredTerrain); Vector2 exploredNodeWorldPos = map.getTileByPos(exploredGridPos.X, exploredGridPos.Y).Position; exploredNode.EstimatedRemainingCost = (int)(endPosition - exploredNodeWorldPos).Length(); //Find nearest tile to the target (in case doesn't find path to target) //Only compares the node to the current nearest FindNearest(exploredNode); openedNodes.Add(exploredNode); } } } } return closedNodes; } After that, I simply check if the end node is contained in the returned nodes. If so, I add the end node and each parent until I reach the start. If not, I add the nearestToTarget and each parent until I reach the start. I added a condition before calling FindPath so that only one unit can call a find path each frame (60 frame per second), but it makes no difference. I thought maybe I could solve this by allowing the find path to run in background while the game continues to run correctly, even if it takes a few frame (it is currently sequential sonce it is called in the update() of the unit if there's a target location but no path), but I don't really know how... I also though about sorting my opened nodes list by cost so I don't have to loop them, but I don't know if that would have an effect on the performance... Would there be other solutions? P.S. In the code, when I get the Move Cost, I check if the unit has to turn to perform the move, and the terrain type, nothing hard to do.

Read the article

C# .Net Serial DataReceived Event response too slow for high-rate data.

- by Matthew

Hi, I have set up a SerialDataReceivedEventHandler, with a forms based program in VS2008 express. My serial port is set up as follows: 115200, 8N1 Dtr and Rts enabled ReceivedBytesThreshold = 1 I have a device I am interfacing with over a BlueTooth, USB to Serial. Hyper terminal receives the data just fine at any data rate. The data is sent regularly in 22 byte long packets. This device has an adjustable rate at which data is sent. At low data rates, 10-20Hz, the code below works great, no problems. However, when I increase the data rate past 25Hz, there starts to recieve mulitple packets on one call. What I mean by this is that there should be a event trigger for every incoming packet. With higher output rates, I have tested the buffer size (BytesToRead command) immediatly when the event is called and there are multiple packets in the buffer then. I think that the event fires slowly and by the time it reaches the code, more packes have hit the buffer. One test I do is see how many time the event is trigger per second. At 10Hz, I get 10 event triggers, awesome. At 100Hz, I get something like 40 event triggers, not good. My goal for data rate is 100HZ is acceptable, 200Hz preferred, and 300Hz optimum. This should work because even at 300Hz, that is only 52800bps, less than half of the set 115200 baud rate. Anything I am over looking? public Form1() { InitializeComponent(); serialPort1.DataReceived += new SerialDataReceivedEventHandler(serialPort1_DataReceived); } private void serialPort1_DataReceived(object sender, SerialDataReceivedEventArgs e) { this.Invoke(new EventHandler(Display_Results)); } private void Display_Results(object s, EventArgs e) { serialPort1.Read(IMU, 0, serial_Port1.BytesToRead); }

Read the article

Bubble sort algorithm implementations (Haskell vs. C)

- by kingping

Hello. I have written 2 implementation of bubble sort algorithm in C and Haskell. Haskell implementation: module Main where main = do contents <- readFile "./data" print "Data loaded. Sorting.." let newcontents = bubblesort contents writeFile "./data_new_ghc" newcontents print "Sorting done" bubblesort list = sort list [] False rev = reverse -- separated. To see rev2 = reverse -- who calls the routine sort (x1:x2:xs) acc _ | x1 > x2 = sort (x1:xs) (x2:acc) True sort (x1:xs) acc flag = sort xs (x1:acc) flag sort [] acc True = sort (rev acc) [] False sort _ acc _ = rev2 acc I've compared these two implementations having run both on file with size of 20 KiB. C implementation took about a second, Haskell — about 1 min 10 sec. I have also profiled the Haskell application: Compile for profiling: C:\Temp ghc -prof -auto-all -O --make Main Profile: C:\Temp Main.exe +RTS -p and got these results. This is a pseudocode of the algorithm: procedure bubbleSort( A : list of sortable items ) defined as: do swapped := false for each i in 0 to length(A) - 2 inclusive do: if A[i] > A[i+1] then swap( A[i], A[i+1] ) swapped := true end if end for while swapped end procedure I wonder if it's possible to make Haskell implementation work faster without changing the algorithm (there's are actually a few tricks to make it work faster, but neither implementations have these optimizations)

Read the article

Linux: How to find all serial devices (ttyS, ttyUSB and others)?

- by Thomas Tempelmann

What is the proper way to get a list of all available serial ports/devices on a Linux system? In other words, when I iterate over all devices in /dev/, how do I tell which ones are serial ports in the classic way, i.e. those usually supporting baud rates and RTS/CTS flow control? The solution would be coded in C. I ask because I am using a 3rd party library that does this clearly wrong: It appears to only iterate over /dev/ttyS*. The problem is that there are, for instance, serial ports over USB (provided by USB-RS232 adapters), and those are listed under /dev/ttyUSB*. And reading the Serial-HOWTO at Linux.org, I get the idea that there'll be other name spaces as well, as time comes. So I need to find the official way to detect serial devices. Problem is that there appears none documented, or I can't find it. I imagine one way would be to open all files from /dev/tty* and call a specific ioctl() on them that is only available on serial devices. Would that be a good solution, though?

Read the article

Demangling typeclass functions in GHC profiler output

- by Paul Kuliniewicz

When profiling a Haskell program written in GHC, the names of typeclass functions are mangled in the .prof file to distinguish one instance's implementations of them from another. How can I demangle these names to find out which type's instance it is? For example, suppose I have the following program, where types Fast and Slow both implement Show: import Data.List (foldl') sum' = foldl' (+) 0 data Fast = Fast instance Show Fast where show _ = show $ sum' [1 .. 10] data Slow = Slow instance Show Slow where show _ = show $ sum' [1 .. 100000000] main = putStrLn (show Fast ++ show Slow) I compile with -prof -auto-all -caf-all and run with +RTS -p. In the .prof file that gets generated, I see that the top cost centers are: COST CENTRE MODULE %time %alloc show_an9 Main 71.0 83.3 sum' Main 29.0 16.7 And in the tree, I likewise see (omitting irrelevant lines): individual inherited COST CENTRE MODULE no. entries %time %alloc %time %alloc main Main 232 1 0.0 0.0 100.0 100.0 show_an9 Main 235 1 71.0 83.3 100.0 100.0 sum' Main 236 0 29.0 16.7 29.0 16.7 show_anx Main 233 1 0.0 0.0 0.0 0.0 How do I figure out that show_an9 is Slow's implementation of show and not Fast's?

Read the article

Can't detect wireless networks, running ubuntu 9.10 on eeepc 1000he

- by David Brown

Hi, I am running Ubuntu 9.10 on an ASUS eeepc 1000HE, and my wireless card, RaLink RT 2860, is failing to recognize any wireless networks. It was working fine this morning, until I accidentally hit Fn F2, disabling the wireless card. I hit Fn F2 again to reenable it, but it no longer will detect any wireless networks (and other computers in the household do recognize them). Any help at all will be greatly appreciated! I googled quite a bit and talked to a human about this but could not fix it. We tried dhclient ra0, which returned There is already a pid file /var/run/dhclient.pid with pid 2438 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/ra0/00:25:d3:13:f4:20 Sending on LPF/ra0/00:25:d3:13:f4:20 Sending on Socket/fallback DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. No working leases in persistent database - sleeping. Other data: iwconfig returns (other stuff here...) ra0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA" Mode:Auto Frequency=2.412 GHz Bit Rate=1 Mb/s RTS thr:off Fragment thr:off Link Quality=10/100 Signal level:0 dBm Noise level:-87 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ifconfig returns (other stuff here...) ra0 Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet6 addr: fe80::225:d3ff:fe13:f420/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:583 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 ra0:avahi Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet addr:169.254.7.117 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:19

Read the article

Linksys WiFi usb dongle and linux woes

- by MrStatic

I have a Linksys WUSB54GC usb dongle and I have exhausted every thing I know about making this thing work in linux. I am using Fedora 13. Since it is not ready I can not view any networks. Any ideas would be great. tail of the system log Jun 2 20:14:35 localhost kernel: usb 1-7: new high speed USB device using ehci_hcd and address 8 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device found, idVendor=1737, idProduct=0077 Jun 2 20:14:35 localhost kernel: usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jun 2 20:14:35 localhost kernel: usb 1-7: Product: 802.11 g WLAN Jun 2 20:14:35 localhost kernel: usb 1-7: Manufacturer: Ralink Jun 2 20:14:35 localhost kernel: usb 1-7: SerialNumber: 1.0 Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::radio Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::assoc Jun 2 20:14:35 localhost kernel: Registered led device: rt2800usb-phy3::quality Jun 2 20:14:35 localhost NetworkManager[1367]: <info> found WiFi radio killswitch rfkill3 (at /sys/devices/pci0000:00/0000:00:1d.7/usb1/1-7/1-7:1.0/ieee80211/phy3/rfkill3) (driver <unknown>) Jun 2 20:14:35 localhost kernel: rt2800usb 1-7:1.0: firmware: requesting rt2870.bin Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): driver supports SSID scans (scan_capa 0x01). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): new 802.11 WiFi device (driver: 'rt2800usb' ifindex: 6) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/4 Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): now managed Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 1 -> 2 (reason 2) Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): bringing up device. Jun 2 20:14:35 localhost kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): preparing device. Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): deactivating device (reason: 2). Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): supplicant interface state: starting -> ready Jun 2 20:14:35 localhost NetworkManager[1367]: <info> (wlan0): device state change: 2 -> 3 (reason 42) [root@localhost log]# iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated Tx-Power=8 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on

Read the article

how to setup kismet.conf on Ubuntu

- by Registered User

I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

Read the article

Wifi network stopped being visible (and usable) (Linksys wag320n)

- by s427

Basically, my wifi network simply stopped working for no apparent reason. It doesn't appear in the list of the available networks anymore. I can see all my neighbors' networks, but not mine. It's as if it doesn't exist anymore. The internet connection (non-wifi), which goes through the same modem/router, is fine though. I already had a similar problem about one year ago (see here: Wifi network SSID not visible ), just after buying this very modem. I finally got it to work after performing two factory resets and getting rid of the Cisco "Magic" software; but this time it's not working. I use a linksys router-modem (WAG320N) which is directly connected (via network cable) to my desktop computer (Windows 7). I have (mainly) two devices that use the wifi network: my phone (Samsung Galaxy Nexus) and an Asus tablet (TF201, aka Transformer Prime). I also resurrected an old laptop computer (Dell, running Windows XP) to test that, and it doesn't see anything either (apart from the 20 other wifi networks, of course ^^). This wifi network was working just fine and has been for about a year. I haven't touched the modem settings so I have no idea what's causing the problem. I tried: making my phone "forget" about my network, hoping it would see it again after that: no luck. re-entering the network informations (SSID/password) manually on my phone: still no luck (says it's not in range) exporting the modem configuration, resetting the modem (factory reset, via modem admin), restarting it, importing the configuration: nope. factory reset, turning it off for 15 minutes, restarting, re-factory reset, and entering the configuration manually: still nothing. Has anybody experienced something similar before? Have you any suggestion to fix that? Thanks in advance. PS: to clear things up, here are the settings of my modem regarding wifi: Basic wireless settings: Configuration: manual Radio Band: 2.4GHz Wireless Network Mode: B/G/N-Mixed SSID: s427 Channel Bandwidth: Wide - 40 MHz Channel Wide Channel: 9 - 2.452GHz Standard Channel: 11 - 2.462GHz SSID Broadcast: Enable Advanced Wireless Settings AP Isolation: Disable Authentication Type: Auto Basic Rate: Default Transmission Rate: Auto N Transmission Rate: Auto CTS Protection Mode: Disable Beacon Interval: 100 DTIM Interval: 1 Fragmentation Threshold: 2346 RTS Threshold: 2346

Read the article

Cannot connect to secure wireless with Netgear wna3100 USB

- by Vince Radice

I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

Read the article

Wireless not working on Dell XPS 17 after installing 12.04

- by user60622

I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

Read the article

Repeated disconnects on WPA PEAP network

- by exasperated

My school has a WPA PEAP network with GTC inner authentication. I am able to connect to the network, but once I load a website or two, the network become unresponsive (i.e. in Chromium, it gets stuck at "Sending request"), and I'm eventually disconnected. Any help will be greatly appreciated. Here's some log output. I can provide more if needed: Ubuntu 13.04 3.8.0-32-generic x86_64 lsusb: 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24) lsmod: iwldvm 241872 0 mac80211 606457 1 iwldvm iwlwifi 173516 1 iwldvm cfg80211 511019 3 iwlwifi,mac80211,iwldvm dmesg: [ 3.501227] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [ 3.503541] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 [ 3.527153] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled [ 3.527162] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled [ 3.527170] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 3.527178] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 3.527186] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_P2P disabled [ 3.527192] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6235 AGN, REV=0xB0 [ 3.527240] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 3.551049] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 375.153065] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 375.159727] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 375.553201] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 375.559871] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 1892.110738] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 1892.117357] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5227.235372] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5227.242122] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5817.817954] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5817.824560] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5824.571917] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 5824.571929] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 5824.571935] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 6956.290061] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 6956.296671] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 6963.080560] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6963.080566] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 6963.080570] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 7613.469241] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 7613.475870] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 7620.201265] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 7620.201278] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 7620.201285] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 8232.762453] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 8232.769065] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 8239.581772] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 8239.581784] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 8239.581792] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [13763.634808] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [13763.641427] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [16955.598953] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [16955.605574] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 lshw: *-network description: Wireless interface product: Centrino Advanced-N 6235 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 24 serial: b4:b6:76:a0:4b:3c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-32-generic firmware=18.168.6.1 ip=10.250.169.96 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:46 memory:f7c00000-f7c01fff iwlist scan: Cell 02 - Address: 24:DE:C6:B0:C7:D9 Channel:36 Frequency:5.18 GHz (Channel 36) Quality=29/70 Signal level=-81 dBm Encryption key:on ESSID:"CatChat2x" Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=0000004ff3fe419b Extra: Last beacon: 27820ms ago IE: Unknown: 0009436174436861743278 IE: Unknown: 01088C129824B048606C IE: Unknown: 030124 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : 802.1x IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1624001B000000FF000000000000000000000000000000 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000 IE: Unknown: DD1A00904C3424001B000000FF000000000000000000000000000000 Cell 04 - Address: 24:DE:C6:B0:C3:E9 Channel:149 Frequency:5.745 GHz Quality=28/70 Signal level=-82 dBm Encryption key:on ESSID:"CatChat2x" Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000181f60e19c Extra: Last beacon: 28680ms ago IE: Unknown: 0009436174436861743278 IE: Unknown: 01088C129824B048606C IE: Unknown: 030195 IE: Unknown: 050400010000 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : 802.1x IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1695001B000000FF000000000000000000000000000000 IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000 IE: Unknown: DD1A00904C3495001B000000FF000000000000000000000000000000 IE: Unknown: DD07000B8601040817 IE: Unknown: DD0E000B860103006170313930333032 Cell 09 - Address: 24:DE:C6:B0:C0:29 Channel:149 Frequency:5.745 GHz Quality=39/70 Signal level=-71 dBm Encryption key:on ESSID:"CatChat2x" Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=00000112fb688ede Extra: Last beacon: 27716ms ago ifconfig (while connected): wlan0 Link encap:Ethernet HWaddr b4:b6:76:a0:4b:3c inet addr:10.250.16.220 Bcast:10.250.31.255 Mask:255.255.240.0 inet6 addr: fe80::b6b6:76ff:fea0:4b3c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:230023 errors:0 dropped:0 overruns:0 frame:0 TX packets:130970 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:255999759 (255.9 MB) TX bytes:16652605 (16.6 MB) iwconfig (while connected): wlan0 IEEE 802.11abgn ESSID:"CatChat2x" Mode:Managed Frequency:5.745 GHz Access Point: 24:DE:C6:B0:C0:29 Bit Rate=6 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:3 Missed beacon:0

Read the article

Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

- by vafa

First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

Read the article

Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

- by Paul H

I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

Read the article

Fixed point math in c#?

- by x4000

Hi there, I was wondering if anyone here knows of any good resources for fixed point math in c#? I've seen things like this (http://2ddev.72dpiarmy.com/viewtopic.php?id=156) and this (http://stackoverflow.com/questions/79677/whats-the-best-way-to-do-fixed-point-math), and a number of discussions about whether decimal is really fixed point or actually floating point (update: responders have confirmed that it's definitely floating point), but I haven't seen a solid C# library for things like calculating cosine and sine. My needs are simple -- I need the basic operators, plus cosine, sine, arctan2, PI... I think that's about it. Maybe sqrt. I'm programming a 2D RTS game, which I have largely working, but the unit movement when using floating-point math (doubles) has very small inaccuracies over time (10-30 minutes) across multiple machines, leading to desyncs. This is presently only between a 32 bit OS and a 64 bit OS, all the 32 bit machines seem to stay in sync without issue, which is what makes me think this is a floating point issue. I was aware from this as a possible issue from the outset, and so have limited my use of non-integer position math as much as possible, but for smooth diagonal movement at varying speeds I'm calculating the angle between points in radians, then getting the x and y components of movement with sin and cos. That's the main issue. I'm also doing some calculations for line segment intersections, line-circle intersections, circle-rect intersections, etc, that also probably need to move from floating-point to fixed-point to avoid cross-machine issues. If there's something open source in Java or VB or another comparable language, I could probably convert the code for my uses. The main priority for me is accuracy, although I'd like as little speed loss over present performance as possible. This whole fixed point math thing is very new to me, and I'm surprised by how little practical information on it there is on google -- most stuff seems to be either theory or dense C++ header files. Anything you could do to point me in the right direction is much appreciated; if I can get this working, I plan to open-source the math functions I put together so that there will be a resource for other C# programmers out there. UPDATE: I could definitely make a cosine/sine lookup table work for my purposes, but I don't think that would work for arctan2, since I'd need to generate a table with about 64,000x64,000 entries (yikes). If you know any programmatic explanations of efficient ways to calculate things like arctan2, that would be awesome. My math background is all right, but the advanced formulas and traditional math notation are very difficult for me to translate into code.

Read the article

Speed Problem with Wireless Connectivity on Cisco 877w

- by Carl Crawley

Having a bit of a weird one with my local LAN setup. I recently installed a Cisco 877W router on my DSL2+ connection and all is working really well.. Upgraded the IOS to 12.4 and my wired clients are streaming connectivity superfast at 1.3mb/s. However, there seems to be an issue with my wireless clients - I can't seem to stream any data across the local wireless connection (LAN) and using the Internet, whilst responsive enough isn't really comparable with the wired connection speed. For example, all devices are connected to an 8 Port Gb switch on FE0 from the Router with a NAS disk and on my wired clients, I can transfer/stream etc absolutely fine - however, transferring a local 700Mb file on my local LAN estimates 7-8 hours to transfer :( The Wireless config is as follows : interface Dot11Radio0 description WIRELESS INTERFACE no ip address ! encryption mode ciphers tkip ! ssid [MySSID] ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 channel 2462 station-role root rts threshold 2312 world-mode dot11d country GB indoor bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding All devices are connected to the Gb Switch which is connected to FE0 with the following: Hardware is Fast Ethernet, address is 0021.a03e.6519 (bia 0021.a03e.6519) Description: Uplink to Switch MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 14000 bits/sec, 19 packets/sec 5 minute output rate 167000 bits/sec, 23 packets/sec 177365 packets input, 52089562 bytes, 0 no buffer Received 919 broadcasts, 0 runts, 0 giants, 0 throttles 260 input errors, 260 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 156673 packets output, 106218222 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Not sure why I'm having problems on the wireless and I've reached the end of my Cisco knowledge... Thanks for any pointers! Carl

Read the article

Linux: How to find all serial devices (ttyS, ttyUSB, ..) without opening them?

- by Thomas Tempelmann

What is the proper way to get a list of all available serial ports/devices on a Linux system? In other words, when I iterate over all devices in /dev/, how do I tell which ones are serial ports in the classic way, i.e. those usually supporting baud rates and RTS/CTS flow control? The solution would be coded in C. I ask because I am using a 3rd party library that does this clearly wrong: It appears to only iterate over /dev/ttyS*. The problem is that there are, for instance, serial ports over USB (provided by USB-RS232 adapters), and those are listed under /dev/ttyUSB*. And reading the Serial-HOWTO at Linux.org, I get the idea that there'll be other name spaces as well, as time comes. So I need to find the official way to detect serial devices. Problem is that there appears none documented, or I can't find it. I imagine one way would be to open all files from /dev/tty* and call a specific ioctl() on them that is only available on serial devices. Would that be a good solution, though? Update hrickards suggested to look at the source for "setserial". Its code does exactly what I had in mind: First, it opens a device with: fd = open (path, O_RDWR | O_NONBLOCK) Then it invokes: ioctl (fd, TIOCGSERIAL, &serinfo) If that call returns no error, then it's a serial dev, apparently. I found similar code here, which suggested to also add the O_NOCTTY option. There is one problem with this approach, though: When I tested this code on BSD Unix (i.e. OSX), it worked as well, however serial devices that are provided thru Bluetooth cause the system (driver) to try to connect to the bluetooth device, which takes a while before it'll return with a timeout error. This is caused by just opening the device. And I can imagine that similar things can happen on Linux as well - ideally, I should not need to open the device to figure out its type. I wonder if there's also a way to invoke ioctl functions without an open, or open a device in a way that it does not cause connections to be made? Any ideas?

Read the article

Is do-notation specific to "base:GHC.Base.Monad"?

- by yairchu

The idea that the standard Monad class is flawed and that it should actually extend Functor or Pointed is floating around. I'm not necessarily claiming that it is the right thing to do, but suppose that one was trying to do it: import Prelude hiding (Monad(..)) class Functor m => Monad m where return :: a -> m a join :: m (m a) -> m a join = (>>= id) (>>=) :: m a -> (a -> m b) -> m b a >>= t = join (fmap t a) (>>) :: m a -> m b -> m b a >> b = a >>= const b So far so good, but then when trying to use do-notation: whileM :: Monad m => m Bool -> m () whileM iteration = do done <- iteration if done then return () else whileM iteration The compiler complains: Could not deduce (base:GHC.Base.Monad m) from the context (Monad m) Question: Does do-notation work only for base:GHC.Base.Monad? Is there a way to make it work with an alternative Monad class? Extra context: What I really want to do is replace base:Control.Arrow.Arrow with a "generalized" Arrow class: {-# LANGUAGE TypeFamilies #-} class Category a => Arrow a where type Pair a :: * -> * -> * arr :: (b -> c) -> a b c first :: a b c -> a (Pair a b d) (Pair a c d) second :: a b c -> a (Pair a d b) (Pair a d c) (***) :: a b c -> a b' c' -> a (Pair a b b') (Pair a c c') (&&&) :: a b c -> a b c' -> a b (Pair a c c') And then use the Arrow's proc-notation with my Arrow class, but that fails like in the example above of do-notation and Monad. I'll use mostly Either as my pair type constructor and not the (,) type constructor as with the current Arrow class. This might allow to make the code of my toy RTS game (cabal install DefendTheKind) much prettier.

Read the article

Linux bcm43224 wifi adapter slows down a couple minutes after boot

- by Blubber

I just installed Ubuntu on my mid 2012 MacBook Air. Everything worked out of the box, but the wifi is showing some weird behavior. When I first login it's really fast, loading google.com is near instant, and browsing in general feels at least as smooth as it did on Mac OS. However, after a couple minutes the connection slows down dramatically, sometimes it takes over 5s to load google.com, a simple reboot fixes the problem for another couple minutes. Specs: Wifi: 02:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) Driver: open-source brcmsmac driver Kernel: Linux wega 3.8.0-21-generic #32-Ubuntu SMP Tue May 14 22:16:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Distro: Ubuntu 13.04 (uptodate) I tried a number of things, none of which actually helped Use proprietary sta driver from broadcom Installed firmware into /lib/firmware/brcms (which, as far as I can tell from logs, does not get loaded at all) Switch router to only use 2.4 OR 5 GHz Set router to only use a OR g OR n Set router to use AES encryption only Turned off power management on the adapter Set regulatory region to the correct value (NL) on both router and laptop Disable ipv6 Nothing seems to help, the slowdown always occurs. I did notice that the latency (ping google.com) stays roughly the same (around 9ms). Below is some more information that might be of use. $ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) Subsystem: Apple Inc. Device [106b:00e9] Kernel driver in use: bcma-pci-bridge $ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lsmod Module Size Used by dm_crypt 22820 1 arc4 12615 2 brcmsmac 550698 0 coretemp 13355 0 kvm_intel 132891 0 parport_pc 28152 0 kvm 443165 1 kvm_intel ppdev 17073 0 cordic 12574 1 brcmsmac brcmutil 14755 1 brcmsmac mac80211 606457 1 brcmsmac cfg80211 510937 2 brcmsmac,mac80211 bnep 18036 2 rfcomm 42641 12 joydev 17377 0 applesmc 19353 0 input_polldev 13896 1 applesmc snd_hda_codec_hdmi 36913 1 microcode 22881 0 snd_hda_codec_cirrus 23829 1 nls_iso8859_1 12713 1 uvcvideo 80847 0 btusb 22474 0 snd_hda_intel 39619 3 videobuf2_vmalloc 13056 1 uvcvideo snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_cirrus bcm5974 17347 0 bluetooth 228619 22 bnep,btusb,rfcomm snd_hwdep 13602 1 snd_hda_codec lpc_ich 17061 0 videobuf2_memops 13202 1 videobuf2_vmalloc videobuf2_core 40513 1 uvcvideo videodev 129260 2 uvcvideo,videobuf2_core bcma 41051 1 brcmsmac snd_pcm 97451 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 16 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_cirrus mei 41158 0 soundcore 12680 1 snd apple_bl 13673 0 mac_hid 13205 0 lp 17759 0 parport 46345 3 lp,ppdev,parport_pc usb_storage 57204 0 hid_apple 13237 0 hid_generic 12540 0 ghash_clmulni_intel 13259 0 aesni_intel 55399 399 aes_x86_64 17255 1 aesni_intel xts 12885 1 aesni_intel lrw 13257 1 aesni_intel gf128mul 14951 2 lrw,xts ablk_helper 13597 1 aesni_intel cryptd 20373 4 ghash_clmulni_intel,aesni_intel,ablk_helper i915 600351 3 ahci 25731 3 libahci 31364 1 ahci video 19390 1 i915 i2c_algo_bit 13413 1 i915 drm_kms_helper 49394 1 i915 usbhid 47074 0 drm 286313 4 i915,drm_kms_helper hid 101002 3 hid_generic,usbhid,hid_apple $ dmesg | egrep 'b43|bcma|brcm|[F]irm' [ 0.055025] [Firmware Bug]: ioapic 2 has no mapping iommu, interrupt remapping will be disabled [ 0.152336] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 2.187681] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-99] only partially covers this bridge [ 12.553600] bcma-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002) [ 12.553657] bcma: bus0: Found chip with id 0xA8D8, rev 0x01 and package 0x08 [ 12.553688] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 12.553715] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 12.553764] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 12.605777] bcma: bus0: Bus registered [ 12.852925] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 17 [ 13.085176] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: false (implement) [ 13.085186] brcmsmac bcma0:0: brcms_ops_config: change power-save mode: false (implement) [ 20.862617] brcmsmac bcma0:0: brcmsmac: brcms_ops_bss_info_changed: associated [ 20.862622] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 20.862625] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 20.897957] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"wlan" Mode:Managed Frequency:5.22 GHz Access Point: E0:46:9A:4E:63:9A Bit Rate=65 Mb/s Tx-Power=17 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=63/70 Signal level=-47 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:13 Invalid misc:56 Missed beacon:0

Read the article

Can't configure frame relay T1 on Cisco 1760

- by sonar

For the past few days I've been trying to configure a data T1 via a Frame Relay. Now I've been pretty unsuccessful at it, and it's been a while, since I've done this so please bare with me. The ISP provided me the following information: 1. IP address 2. Gateway address 3. Encapsulation Frame Relay 4. DLCI 100 5. BZ8 ESF (I think the bz8 was supposed to be b8zs) 6. Time Slot (1 al 24). And what I have configured up until now is the following: interface Serial0/0 ip address <ip address> 255.255.255.252 encapsulation frame-relay service-module t1 timeslots 1-24 frame-relay interface-dlci 100 sh service-module s0/0 (outputs): Module type is T1/fractional Hardware revision is 0.128, Software revision is 0.2, Image checksum is 0x73D70058, Protocol revision is 0.1 Receiver has no alarms. Framing is **ESF**, Line Code is **B8ZS**, Current clock source is line, Fraction has **24 timeslots** (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec. Last module self-test (done at startup): Passed Last clearing of alarm counters 00:17:17 loss of signal : 0, loss of frame : 0, AIS alarm : 0, Remote alarm : 2, last occurred 00:10:10 Module access errors : 0, Total Data (last 1 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Data in current interval (138 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs sh int: FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 000d.6516.e5aa (bia 000d.6516.e5aa) Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:20:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 191 packets output, 20676 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 157, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 23, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 0 Last input 00:24:51, output 00:00:05, output hang never Last clearing of "show interface" counters 00:27:20 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1152 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 23 packets input, 302 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 1725 input errors, 595 CRC, 1099 frame, 0 overrun, 0 ignored, 30 abort 246 packets output, 3974 bytes, 0 underruns 0 output errors, 0 collisions, 48 interface resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Serial0/0.1 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never Serial0/0.100 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU Internet address is <ip address>/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never And everything seems to be accounted for to me, but apparently I'm missing something. My issue is that I'm stuck on interface up, line protocol down, so the T1 doesn't go up. Any ideas? Thank you,

Read the article

Enable wireless on Dell Inspiron 1300

- by Simon

As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

Search Results

Search found 213 results on 9 pages for 'rts'.

Page 8/9 | < Previous Page | 4 5 6 7 8 9 | Next Page >

- by statquant

- by mgeorge

- by TalonPlz

- by JohnMerlino

- by Amaranth

- by Matthew

- by kingping

- by Thomas Tempelmann

- by Paul Kuliniewicz

- by David Brown

- by MrStatic

- by Registered User

- by s427

- by Vince Radice

- by user60622

- by exasperated

- by vafa

- by Paul H

- by x4000

- by Carl Crawley

- by Thomas Tempelmann

- by yairchu

- by Blubber

- by sonar

- by Simon

< Previous Page | 4 5 6 7 8 9 | Next Page >